Boiler efficiency is called to some extent of total thermal energy which can be recovered from the fuel. Boiler efficiency losses are due to four major factors: the dry gas flux, the latent heat of steam in the flue gas, the combustion loss or the loss of unburned fuel, radiation and convection losses. In this research, the thermal behavior of boilers in gas refinery facilities is studied and their efficiency and their losses are calculated. The main part of this research is comprised of analyzing the effect of various parameters on efficiency such as excess air, fuel moisture, air humidity, fuel and air temperature, the temperature of combustion gases, and thermal value of the fuel. Based on the obtained results, it is possible to analyze and make recommendations for optimizing boilers in the gas refinery complex using response-surface method (RSM).

This study provides a methodology for optimizing oil production and CO2 sequestration using an integrated asset model of the Farnsworth Unit field, incorporating extensive geological, geophysical, and engineering data. Sensitivity analysis identified critical parameters impacting oil recovery and CO2 storage, leading to the construction of a proxy model using polynomial regression and radial basis function neural networks, with the latter proving more effective for "What-if" analysis. The sensitivity analysis indicated that the Corey parameters impact cumulative oil produced the most. Comprehensive history matching validated the model against historical production data, ensuring reliability for forecasting and optimization. Two scenarios, "Do-Nothing" and development strategy, were forecasted over 15 years (2020-2035). The "Do-Nothing" scenario resulted in 9.57 MMSTB of oil recovery and 2,822.70 MMlbs of CO2 storage. The development strategy case improved outcomes with 13.95 MMSTB of oil recovery and 5,061.68 MMlbs of CO2 stored, and was selected for optimization using particle swarm optimization. The optimized strategy achieved 14,043,372 STB of cumulative oil and 4,832.18 MMlbs of CO2 stored, and increased the field NPV by 25.84% to $114,871,730. This study underscores the significance of integrated asset modeling in enhancing oil recovery and optimizing CO2-EOR processes, providing valuable insights into operational conditions and constraints.

Multiphase systems are important in minerals processing, and usually include solid-solid and solid-fluid systems. Examples of operations in multiphase systems include flotation, dewatering, and magnetic separation, among several other unit operations. In this paper, the current trends in the process system engineering tasks of modeling, design, and optimization, in multiphase systems, are analyzed. Different scales of size and time are included, and therefore the analysis includes modeling at the molecular level and unit operation level, and the application of optimization for the design of a plant. New strategies for the modeling and optimization of multiphase systems are also included, with a strong focus on the application of artificial intelligence (AI) and the combination of experimentation and modeling with response surface methodology (RSM). The paper finishes with tools to study the uncertainty, both epistemic and stochastic, which is present in all mineral processing operations. It is shown that all these areas are very active and can help to understand, operate, design, and optimize mineral processing that involves multiphase systems.

In power systems there are complex transformer structures, whose accurate analysis is not possible using the techniques available today. This paper presents a systematic data driven analysis method for coupled inductors of arbitrary complexity. The method first establishes a winding matrix N mapping the windings to the limbs of the transformer. A permeance matrix P is created from the reluctance network of the magnetic core. A generalized inductance matrix L mapping currents in the transformer windings to the induced voltages is generated based on the winding (N) and permeance (P) matrices. The inductance matrix representation of a coupled inductor is then transformed to an admittance matrix, which can be integrated to the nodal analysis of the electrical circuit surrounding the coupled inductor. The method presented is validated by simulations with real transformer structures using electromagnetic transient program (EMTP/ATP).

Green synthesis of silver nanoparticles (AgNPs) using raw Whey has never been reported. Silver nanoparticle formation involves a reduction reaction of silver salt solution with Whey extract. Extract and metal salt concentrations, and temperature can control this reaction. In this work, incubation period, extract, AgNO3, and NaOH concentrations were used as the independent factors using central composite design under response surface methodology. The aim was to elucidate the influence these factors have on the measured UV-Vis absorption spectra fitted with a Voigt function, and to optimize the conditions for nanoparticle formation. The fitting parameters, peak wavelength (λ0), peak area (A), and Full Width at Half Maximum (FWHM), were the responses. Silver nanoparticle formation was only possible in an alkaline environment (pH 10). The peak wavelength and the FWHM are influenced mainly by extract and AgNO3 concentrations. In contrast, the peak area is influenced by a total of 33.54 % from the interaction terms of AgNO3 and extract concentrations with NaOH. Metallic AgNPs were formed for the following parameter ranges: a) Whey (0.4 – 1.6 % v/v), b) AgNO3 (0.15 – 0.6 mM), c) NaOH (10 – 50 mM), and d) Time (20 – 60 min). Silver oxide nanoparticles were also observed.

Surface–subsurface soil-rock modeling is crucial for infrastructure design and groundwater yield optimization, especially in the complex crystalline basement terrains of Penang Island, Malaysia. This study conducted large-scale characterization of soil-rock profiles using ERT, SRT, rock quality designation, and soil penetration test (SPT N-values) data, optimized through regression modeling. The approach effectively identified soil-rock structures and their suitability to prevent structural failures and enhance groundwater productivity. Correlations between borehole lithologic logs and velocity–resistivity models revealed distinct soil compositions across the study area. The results highlighted thick, saturated, and loose silty to sandy bodies in the eastern to northern sections, contrasting with sandy compositions and penetrative fractures in the southern part. The study also found good correlations between rock mass quality and N-values for different soil types. Depths of intra-bedrock weathered/fractured units varied between 12 and >35 m. This has significant implications for determining optimal foundation depths in the study area. Groundwater productivity was associated with intra-bedrock planes of weakness at depths exceeding 40 m. Overall, this study developed empirical relations between geophysical and geotechnical parameters for wet tropical granitic terrains, filling critical gaps in understanding subsurface characteristics.

Chemical vapor deposition (CVD) is a vital process for depositing thin films of various materials with precise control over thickness, composition, and properties. Understanding the heat and mass transfer mechanisms during CVD is essential for optimizing process parameters and ensuring high-quality film deposition. This review provides an overview of recent advancements in the heat and mass transfer modeling for chemical vapor deposition processes. It explores innovative modeling techniques, recent research findings, emerging applications, and challenges in the field. Additionally, it discusses future directions and potential areas for further advancement in CVD modeling.

In the process of sewage coagulation treatment, quartz sand is often used as a heavy medium to accelerate the settling rate of flocs, but it will adversely affect the removal efficiency of pollutants. The factors that affect the coagulation effect and can be controlled manually include the quartz sand dosage, coagulant dosage, sewage pH, stirring time, settling time, etc, their reasonable setting is critical to. This paper was to study the optimal conditions of quartz sand enhanced coagulation(QSEC), first, single-factor tests were conducted to preliminarily explore the optimal range of influencing factors, and then response surface methodology（RSM）tests were performed to accurately determine the optimums of significant factors. The results showed that the addition of quartz sand can’t improve the water quality of coagulation treatment, but it can significantly accelerate the coagulation settlement process, the quartz sand dosage, the coagulant dosage and sewage pH all impacted significantly on its coagulation effect, and existed inflection points. A model that could guide QSEC was obtained by RSM tests. The model optimization and experimental validation showed that the optimal QSEC conditions for treating domestic sewage were as follows: the polyaluminum chloride(PAC) dosage, cationic polyacrylamide(CPAM) dosage, the sewage pH, quartz sand dosage, stirring time and settling time were 0.97 g·L-1, 2.25 mg·L-1, 7.22, 2 g·L-1, 5 minutes and 30 minutes, respectively, and the turbidity of treated sewage was reduced to 1.15 NTU.

Lactoperoxidase (LP), which is a high-value minor whey protein, has recently drawn extensive attention from research scientists and industry due to its multi-function and potential therapeutic applications. In this study, the separation and optimization of two similar-sized proteins, LP and lactoferrin (LF) were investigated using strong cation exchange column chromatography. Optimization was started with central composite design based experiments to characterize the importance of different decision variables. The three variables used in the optimization were flow rate, length of gradient and final salt concentration in the linear elution gradient step. The obtained empiric functional model represented the effect of the significant factors on the yield as the objective function. Afterwards, the calibrated mechanistic model was employed to predict accurate optimal set of variables. The optimal operating points were found and the results were compared with validation experiments. Predictions respecting yield confirmed a very good agreement with experimental results while keeping purity, a product quality characteristic, equal or above to a predefined value.

For marine vessels, a propeller shaft system, also known as a propulsion shaft system, is an essential changer in engine torque and propeller thrust. The propeller shaft system is subjected to transverse, longitudinal, and torsional excitations during operation. These sources of excitations originate from alternating thrust generated by the propeller, operation of a propeller in a stern flow field which is non-uniform in time and space, misalignment of components such as shafts, bearings, and keyholes in the assembly, excitations in the form of rotational motion, and the whirling motion of the shafts. These dynamic excitations posed a challenging issue for the integrity and reliability of a marine vehicle. Thus, it is crucial to analyze the dynamic response of the propulsion shaft system. The dynamic analysis of the propulsion shaft system is typically conducted using numerical /analytical models. At present, Finite Element Model (FEM) as a numerical model plays a vital role in analyzing the dynamic response of the structure. The computed response and the modal parameters from the FE model are reliable only if accurate boundary conditions, such as stiffness, can be imposed on the model. However, the numerical FE model deviates from the experimental results because of uncertainties in the stiffness values of the bearings and other connectors. This paper uses the Response Surface Optimization (RSO) technique to estimate the unknown stiffness of the bearings used in the propulsion shaft system. The experimental model of the propeller shaft system is constructed from the steady-state response of the system using the step sine excitation. The natural frequencies and the amplitude of vibrations in the FE model are updated using the parametric RSO technique. The updated model shows that the difference in natural frequencies and vibration amplitude is less than 10% between the optimized and experimental models. Propeller Shaft, Vibrations, Optimization, Response Surface

This study was designed for the first time to improve phenolic yield and antioxidant activity of ultrasonic-assisted extraction from Acer truncatum leaves (ATL) using response surface methodology, and phenolic composition in ATL extracted under the optimized condition were characterized by UPLC-QTOF-MS/MS. Solvent and extraction time were selected based on preliminary experiments, and a four-factors-three-levels central composite design was conducted to optimize solvent concentration (X₁), material-to-liquid ratio (X₂), ultrasonic temperature (X₃) and power (X₄) for an optimal total phenol yield (Y₁) and DPPH• antioxidant activity (Y₂). The results showed that the optimal combination was ethanol: water (v:v) 66.21%, material-to-liquid ratio 1:15.31 g/mL, ultrasonic temperature 60 °C, power 267.30 W, and time 30 min with three extractions, giving a maximal total phenol yield of 7593.62 mg gallic acid equivalent /100 g d.w. and a maximal DPPH• antioxidant activity of 74241.61 μmol Trolox equivalent/100 g d.w.. Furthermore, 22 phenolics were first identified in ATL extract obtained under the optimized conditions, indicating that gallates, gallotannins, quercetin, myricetin and chlorogenic acid derivatives were the main phenolic composition in ATL. What’s more, a gallotannins pathway existing in ATL from gallic acid to penta-O-galloyl-glucoside was interpreted. All these results provided practical information aiming at full utilization of phenolics in ATL, together with fundamental knowledge for further research.

In numerical simulations, achieving high accuracy without significantly increasing computational costs is often challenging. To address this, this paper presents an improved finite volume weighted essentially non-oscillatory (WENO) scheme tailored for applicability in computational fluid dynamics (CFD) and implemented in the flow solver NUAA-Turbo for simulating turbomachinery flows using both RANS and RANS/LES coupling. Firstly, the new WENO scheme is validated against classic numerical test cases to assess its stability and reliability in handling discontinuities, the Double problem, and Raleigh-Taylor (RT) instability issues. Compared to the original format, this enhanced finite volume WENO scheme demonstrates superior stability near discontinuities and resolves flow features with the same grid resolution more effectively. Next, for engineering applications related to turbomachinery, such as compressor and turbine characteristics, computations are performed using RANS, and the results obtained using WENO-ZQ3 and WENO-JS3 are compared. Finally, the new fifth-order WENO scheme is applied to RANS/LES coupled simulations of turbine wakes and film cooling. The results show that the enhanced finite volume WENO scheme offers improved stability and accuracy in engineering applications, allowing for high-precision calculations with fewer grid points to capture more detailed flow physics, thereby reducing computational costs in aerodynamic applications.

Practical entanglement distillation is a critical component in quantum information theory. Entanglement distillation is often utilized for designing quantum computer networks and quantum repeaters. The practical entanglement distillation problem is formulated as a bilevel optimization problem. A fuzzy formulation is introduced to estimate the quantum state (density matrix) from pseudo-likelihood functions (i.e., quantum state tomography). A scale-independent relationship between fuzzy relations in terms of the pseudo-likelihood functions is obtained. The entanglement distillation optimization problem was solved using the combined coupled map lattice and dual annealing approach. Comparative analysis of the results is then conducted against a standard dual annealing algorithmic implementation.

Nano surface finishing can be achieved from the recently developed electrophoretic deposition-assisted polishing (EPDAP) process. This state-of-art work presents a comparison of the effect of surface roughness and material removal rate on the grit size, axial load, rotational speed, polishing time, etc. for SS304, SS316L and alumina ceramics. The EPDAP process can assess the surface's characteristics' quantity, and quality on different materials which have been tried on SS316L, SS304, inner bore of SS304, and Al2O3 in our laboratory. Uniform dispersion of homogeneous micro-sized abrasive grains was accomplished by electrophoretic deposition (EPD) to create the polishing tool employed in this process. Polishing time, axial loading, grit size, and speed of rotation of the polishing tool was selected as the control parameters. The polishing tool undergoes erosion of blunt-edged-abrasive grains due to abrasion during the EPDAP process. Therefore, the polishing tool was continuously revitalized by adding fresh abrasives. The analysis of the experiments is conducted using ANOVA and the evolutionary algorithm teaching-learning method. EPDAP process revealed improved surface reflection as well as improvement in surface finish. Thus, optimization of the polishing parameters was conducted for the experiments. The surface roughness achieved from the experiments is 0.04557 microns for SS316L, 0.038 microns for SS304, and 0.404 microns for Al2O3. Therefore, 93.92%, 97.64 %, and 73.75 % of improvement in the surface finish were achieved in SS316L, SS304, and Al2O3, respectively.

During the last decade, Bangladesh has been experienced a significant climatic anomalies which lead to an increase in magnitude and frequency of various climate relate extreme events. Climate scientists substantiate that global temperature and precipitation pattern is expected to change, which may result in consequential impact on agriculture, livelihood, and ecosystem. Bangladesh is therefore likely to face substantial challenges in the coming decades. In order to adequately understand this complex, dynamic phenomena, Analyzing historical Climate change scenarios as well as projecting its future trends is a great concern for researcher. This study aims to analyzes/ historical climatic data from (1901-2020), and predict future temperature and precipitation patterns in Bangladesh using CMIP6 data. Data used in this study (Observed data is from CRU TS 4.05 and future data is from CMIP6) have been acquired from WorldClim v2.1. Various methods including correlation, regression, standard deviation, correlation matrix, percentiles, cell statistics, and IDW interpolation were performed to analyze the trends, variability and spatial patterns of temperature and rainfall. This study revealed that Over the historical study period (1901-2020) Bangladesh has been experienced a significant warming trend with an average increase in temperature 2°C and with annual decline of the total precipitation 607.26 mm along with a shift towards drier conditions despite weak correlation with hotter years. Projected climate models represents that Bangladesh minimum temperature is expected to increase from 1°C to 4.4°C as well as maximum temperatures from 1°C to 4.1°C by 2100. Moreover, projected precipitation is expected to increase by 480.38 mm, with the biggest rises during monsoon months. Regional variations in temperature and precipitation are again expected, with the Southeast (SE) likely experiencing the most significant warming and the Northeast (NE) seeing the most substantial increase in precipitation.

This paper proposes the use of non-uniform extended surfaces installed externally to the tubes of the radiation section of fired heaters, in order to obtain a better heat flux distribution to the coils. To this end, the heat transfer mechanisms present in such equipment were studied through computational fluid dynamics (CFD), using simplified geometries that represent typical sizes of fired heaters. Also, a simplified model for the combustion was considered. Although this model oversimplifies the physics of the problem, it was able to give satisfactory results for the parameters being optimized, considering the main objective of this paper, that is to minimize the non-uniformity of heat flux in the tubes of the radiant section of fired heaters. It was possible to obtain optimized geometric parameters for different types of extended surfaces evaluated, coupling the results of these models with the Particle Swarm optimization method through the use of a response surface technique,. The results indicate a significant improvement in the uniformity of the heat flux distribution to the tubes through the use of the proposed extended surfaces. Thus, this solution reveals to be an interesting alternative to reduce the risks of fluid degradation and coking formation. Future studies must investigate the non-uniformity of the heat flux due to the presence of the flame and consider the interaction between the reactive flow and the participating medium. Nevertheless, this paper presents some results that justify the optimization of such extended surfaces taking into consideration thermal radiation.

A coupled stratospheric chemistry-meteorology model was developed by combining the Canadian operational weather prediction model Global Environmental Multiscale (GEM) with a comprehensive stratospheric photochemistry model from the Belgian Assimilation System for Chemical ObsErvations (BASCOE). The coupled model was called GEM-BACH for GEM-Belgian Atmospheric CHemistry. The coupling was made across a chemical interface that preserves time splitting while being modular, allowing GEM to run with or without chemistry. An evaluation of the coupling was performed by comparing the coupled model, refreshed by meteorological analyses every 6 hours, against the standard offline chemical transport model (CTM) approach. Results show that the dynamical meteorological consistency between meteorological analysis times far outweighs the error created by the jump resulting from the meteorological analysis increments at regular time intervals, irrespective whether a 3D-Var or 4D-Var meteorological analysis is used. GEM-BACH forecast refreshed by meteorological analyses every 6 hours were compared against independent measurements of temperature, long-lived species, ozone and water vapor. The comparison showed a relatively good agreement throughout the stratosphere except for an upper-level warm temperature bias and an ozone deficit of nearly 15%. Arguments in favor of using the same horizontal resolution for chemistry, meteorology, and meteorological analysis increments are also presented. In particular, the coupled model simulation during an ozone hole event gives better ozone concentrations than a 4D-Var chemical assimilation at a lower resolution.

Buckling defect will appear on the outer surface of the deformed ring during constrained ring rolling (CRR) of aluminum alloy thin wall conical ring with inner high ribs (AATWCRIHR), if the geometrical dimension of the ribs doesn't match the wall thickness. To avoid the buckling defect, a quantitative method for characterizing the degree of the buckling defect is proposed using the area of buckling profile. Then an orthogonal experimental scheme was designed taking the width of the middle rib, thickness of wall, and height of the middle rib as design variables and defining the area of buckling profile as optimization objective. Subsequently, a quadratic polynomial response surface model was established by combining the optimization algorithm with the finite element method (FEM), and the geometrical dimension of the middle ribs of the deformed AATWCRIHR is optimized. Also the optimal parameter combination to minimize the area of buckling profile is obtained and verified using FE simulation. Results show that the AATWCRIHR after optimization doesn’t generate the buckling defect during constrained ring rolling, and it is proved that the quantitative buckling defect representation method and the optimization design method based on the response surface model and the finite element simulation results are feasible for the constrained ring rolling process of the AATWCRIHR.

The present work aims at the comprehensive application of stochastic and optimization tools with the support of Information and Communication Technologies (ICT) through a case study in a logistics process for electronic goods; simulation and Response Surface Methodology (RSM) are applied for this purpose. The problem to be evaluated is to define an optimal distribution cost for products shipped to wholesale customers located in different cities in Mexico from a manufacturing plant in Tijuana, Mexico. The factors under study are the product allocation for each distribution center, finished good inventory level and on time deliveries, which are supposed to be significant to get the objective. The methodology applied for this problem considers the design of a discrete event simulation model to represent virtually the real life of logistics process, which is considered a complex system due to different activities are interrelated to carry it out. This model is used to execute the different experiments proposed by the RSM. The results obtained from simulation model were analyzed with the RSM to define the mathematical model that allows identifying the parameters of the factors in order to optimize the process. The findings prove how the ICT facilitate the application of stochastic tools with the purpose of process optimization.

Daily maximum surface air temperature (Tamax) is a crucial factor for understanding complex land surface processes under rapid climate change. Remote detection of Tamax has widely relied on the empirical relationship between air temperature and land surface temperature (LST), a product derived from remote sensing. However, little is known about how such a relationship is affected by the high heterogeneity in landscapes and dynamics in seasonality. This study aims to advance our understanding of the roles of land cover and seasonal variation in the estimation of Tamax using the MODIS (Moderate Resolution Imaging Spectroradiometer) LST product. We developed statistical models to link Tamax and LST in the middle and lower reaches of the Yangtze River in China for five major land-cover types (i.e., forest, shrub, water, impervious surface, cropland, and grassland) and two seasons (i.e., growing season and non-growing season). Results show that the performance of modeling the Tamax-LST relationship was highly dependent on land cover and seasonal variation. Estimating Tamax over grasslands and water bodies achieved superior performance; while uncertainties were high over forested lands that contained extensive heterogeneity in species types, plant structure, and topography. We further found that all the land-cover specific models developed for the plant non-growing season outperformed the corresponding models developed for the growing season. Discrepancies in model performance mainly occurred in the vegetated areas (forest, cropland, and shrub), suggesting an important role of plant phenology in defining the statistical relationship between Tamax and LST. For impervious surfaces, the challenge of capturing the high spatial heterogeneity in urban settings using the low-resolution MODIS data made Tamax estimation a difficult task, which was especially true in the growing season.

Sustainable development advocates for an environmentally friendly and resource-saving approach, fostering a new quality of productivity that is green and sustainable, and achieving a sustainable development where the economy and the environment are in harmony. The paper is based on clarifying the effects of coordinated development between the economy and the environment, and by establishing an indicator system, applying a remote sensing ecological index, entropy weight method, gray relational degree model, and a coupling coordination model, the relationship of coordinated development of Ordos in 2016-2022 is analyzed from a spatial-temporal perspective. The results are as follows: ① The years of coordinated development between the ecological environment and the economy are in the majority, while the uncoordinated years are fewer. ② The level of coordinated development between the ecological environment and the economy in the various regions of Ordos has been increasing year by year, but it still remains at the barely coordinated and primary coordinated levels. ③ The types of coordinated development between the ecological environment and the economy in Ordos exhibit significant spatial differentiation in terms of spatial distribution and clustering.Therefore, it is necessary to formulate coordinated development policies and measures according to the constraining factors of different regions.

Objective: To determine the effect of sandblasting before and after sintering on the surface roughness of zirconia and the micro-tensile bond strength of a pressable veneering ceramic to zirconia. Methods: Pre-sintered zirconia blocks (IPS e.max ZirCAD, Ivoclar Vivadent) were divided into a control group (CTR, no surface treatment) and four test groups of three specimens each: Pre-S-30, Pre-S-50, Pre-S-110 were sandblasted with 30µm SiO2, 50µm Al2O3 and 110µm Al2O3 particles respectively, before sintering, Post-S-30 was sandblasted with 30µm SiO2 after sintering. For each treatment, the surface roughness was measured (Ra, Perthometer M4P, Mahr Perthen). After sintering the zirconia blocks, a liner and a pressable ceramic (IPS e.max ZirPress, Ivoclar Vivadent) were fired. Sixteen micro-bars were obtained from each block and submitted to the micro-tensile bond strength (µTBS) test. Data were analyzed with one-way ANOVA. Any correlation between Ra and µTBS was evaluated (Sperman test). Results: Sandblasting before sintering with 110µm Al2O3 (Ra=3.44±0.44µm), 50µm Al2O3 (Ra=2.32±0.46µm), and 30µm SiO2 (Ra=1.22±0.22µm) resulted in significantly higher roughness than sandblasting after sintering with 30µm SiO2 (Ra=0.46±0.11µm). The highest µTBS was measured when the sintered zirconia was sandblasted with 30μm SiO2 (26.79±14.80 MPa), which was significantly different from that of specimens that were sandblasted before sintering (Pre-S-30=20.90±11.70; Pre-S-50=21.27±15.19; Pre-S-110=23.99±16.83) or were not treated (CTR=17.44±14.03). Conclusions: Sandblasting zirconia before sintering enhances the surface roughness proportionally to the particle size of the sand used. Sandblasting with 30µm SiO2 after sintering appeared to improve bonding between the veneering ceramic and zirconia. Clinical Significance: Sandblasting with 30µm SiO2 after sintering may improve bonding between veneering ceramics and zirconia, thus reducing ceramic fractures/chippings.

Citrus peels are considered as a rich source of valuable biomolecules like pectin as polymer of polysaccharide acid. In this study, response surface methodology was used to optimize pectin extraction from Citrus clementina peels using citric acid as extraction solvent. The effect of parameters conditioning the extraction process and pectin yield (pH, temperature, extraction time, solid/liquid ratio, and raw material particle size) was investigated using a Box-Behnken design. The quality of the extracted pectin was assessed both chemically (moisture, ash, protein, and sugar content) and functionally (gelling power and emulsifying activity). According to the screening experiment, the factors pH, temperature, and particle size were the main factors influencing the pectin yield. The adjusted mathematical model enabled us to plot response surfaces in order to determine optimal extraction conditions. The highest production yield of pectin (26.6%) was obtained at the optimal conditions of: pH = 1.5; temperature 100 °C and particle size = 0.1 mm for an extraction time of 30min. Compared to the predicted value of 26.6%, the experimental extraction yield was about 21.4% of pectin. Concerning the functional properties, the extracted pectin has a high gelling power of 164°SAG and an emulsifying activity of 38.5%.

The fast decoding of low-density parity-check (LDPC) is crucial for its future applications. In this paper, we propose to use Early Termination (ET) and Force Convergence (FC) techniques to accelerate the decoding of two new local/global two-phases decoding algorithms to reduce the Globally Coupled (GC) LDPC codes. Specifically, ET is applied in the local decoding phase of two- phases decoding of GC-LDPC codes to skip the local decoding which is highly likely to fail and avoid the unnecessary iterations. FC is applied in global decoding phase where converged variable nodes are identified and removed from Tanner graph and the decoding can be speed up shrinking parity check matrices. Two variants are proposed for the ET operation in local decoding phase. ET-1 merely stops iteration if it meets the stopping criterion while in ET-1, the iteration number saved in local decoding is added up in global decoding to improve the decoding performance. The simulation results show that the ET-1-FC scheme can save up to 42% decoding time complexity in the low SNR region while keeping the error rate performance nearly unchanged, the ET-2-FC can improve the error rate performance by 0.18dB at bit error rate 0.001 or 0.23dB at frame error rate 0.1. In the waterfalling region of BER/FER curves, both schemes can save about 25% decoding time complexity.

Sea surface wind forecasts in the Adriatic Sea often suffer for unadequate modelling, especially for the wind speed. This has detrimental effects on the accuracy of sea level and storm surge predictions. We present a numerical method to reduce the bias between the sea surface wind observed by the scatterometers and that supplied by the European Centre for Medium-Range Weather Forecasts (ECMWF) global atmospheric model, for storm surge forecasting applications. The method, called “wind bias mitigation”, relies on scatterometer observations to determine a multiplicative factor ∆ws which modulates the standard model wind in order to decrease the bias between scatterometer and model. We compare four different mathematical approaches to this method, for a total of eight different formulations of the multiplicative factor ∆ws. Four datasets are used for the assessment of the eight different bias mitigation methods: a collection of 29 Storm Surge Events (SEVs) cases in the years 2004-2014, a collection of 48 SEVs in the years 2013-2016, a collection of 364 cases of random sea level conditions in the same period, and a collection of the seven SEVs in 2012-2016 that were worst predicted by the Centro Previsioni e Segnalazioni Maree, Comune di Venezia (Tide Forecast and Early Warning Centre of the Venice Municipality - CPSM). The statistical analysis shows that the bias mitigation procedures supplies a mean wind speed more accurate than the standard forecast, when compared with scatterometer observations, in more than 70% of the analyzed cases.

Using the example of a generator model with dedicated inertia, a theoretical study of two coupled self-oscillators with capacitive coupling, their sequential single-frequency synchronization, chaos and two-frequency synchronization with an adiabatic change in the magnitude of the coupling between partial self-oscillators was carried out. The parameters of self-oscillators and the values of the coupling coefficient at which the specified operating modes of coupled self-oscillators exist are determined. The results of numerical studies, illustrating the conditions for excitation of single-frequency, chaotic and dual-frequency oscillations in a system of coupled self-oscillators are presented.

Due to the non-degradability of petroleum-based packaging materials, serious environmental pollution and the depletion of non-renewable resources have become pressing issues. In order to actively promote green production and address these concerns, there is an urgent need for new packaging materials to replace traditional plastic products. Starch-based packaging materials, composed of starch, fiber, and plasticizers, offer a degradable and environmentally friendly alternative. Starch alone cannot undergo thermoplastic processing due to its inherent structural characteristics. Therefore, researchers have explored modifications by incorporating plasticizers to create processable thermoplastic starch (TPS). However, there are challenges related to the high crystallinity and poor compatibility between TPS and fibers, resulting in decreased mechanical properties. To address these challenges, a novel approach combining plasticizer optimization and response surface method (RSM) optimization has been proposed to enhance the mechanical properties of starch-based packaging materials. This method leverages the advantages of composite plasticizers and process parameters. The findings demonstrate that the composite plasticizer effectively disrupt the hydrogen bonding and granule morphology of starch, leading to a significant reduction in crystallinity. Based on these findings, the optimal process parameters are determined using the RSM, resulting in a forming temperature of 198 °C, forming time of 5.4 minutes, and AC content of 0.84 grams. Compared with the non-optimized values, the tensile strength increases by 12.2% and the rebound rate increases by 8.1%.

Silicon carbide single crystal (SiC) has been widely used in the field of power devices, while it is difficult to fabricate ultra-flat surface by traditional manufacturing technologies due to its difficult-to-machine property. This paper investigates the interaction process during femtosecond laser ablation of crystalline silicon carbide based on the two-temperature model simulation and experimental study. The findings reveal that parameters such as laser pulse energy, scanning interval, and defocus amount exert significant influence on ablation depth, roughness, and surface morphology. The femtosecond laser proves effective in removing surface defects from cut SiC substrates, albeit resulting in increased surface roughness. However, subsequent polishing treatment of the laser-ablated silicon carbide surface can mitigate this roughness, underscoring the feasibility of laser surface ablation for silicon carbide single crystals.

The digital model of airborne frequency selective surface radomes (AFSSRs) is the basis of design, simulation analysis, manufacturing, and other related research of AFSSRs. This paper proposes a rapid modeling method of AFSSRs based on dynamic customizable primitives. Firstly, a layered digital model construction scheme of AFSSR is presented based on the typical radome wall structure. Then, according to the characteristics of various surface configurations and complex wireframe information of AFSSRs, the dynamic primitives are raised to express the boundary and contour information of all kinds of radomes. Focusing on the undevelopable characteristics of the aero-dynamic shape surface of the AFSSR, the arrangement solution and mapping method for frequency selective elements on undevelopable surfaces are proposed. Furthermore, the imple-mentation logic of this method on the creation of each layer model and the assembly of the whole machine model is introduced. Finally, according to this method, a rapid modeling system (RMS) is established, and the modeling effect and efficiency of the RMS are demonstrated and compared, which verifies the feasibility and effectiveness of this method.

Using the above results from RMS analysis the optimum values were predicted for the independent significant variables (Figure 3) the optimized levels of these variables in combination with other media variables the maximum production was predicted to be 199.90 U/mL. The predicted data were validated through confirmatory experiments performed in triplicates. A 1.29-fold increase in amylase activity against un-optimized (OVAT) medium was achieved in the present study authenticating the efficacy of RSM in process optimization (Figure 4). 2.6 Model validation and scale-up at laboratory scale (5L) bioreactor Once the parameters were standardized in the shake-flasks culture, the experiment was scaled-up to a laboratory-scale bioreactor (5 L). The yield of amylase increased by 1.01 fold (205.69 U/mL), it could be possible because the enzyme production in a bioreactor is higher than in shake-flasks culture as the various critical variable factors such as the dissolved oxygen (DO) and the pH can be optimally controlled at the desired levels [22].

Nickel based superalloys finds extensive usage in manufacturing of intricate part shapes in gas turbine, aircraft, submarine, and chemical industries owing their excellent mechanical property and heat resistant abilities. However, machining of such difficult-to-machine alloys up to the desired accuracy and preciseness is a complex task owing to a rapid tool wear and failure. In view of this, present work proposes an experimental investigation and optimization of process parameters of the cryogenic assisted turning process during machining of Nimonic C-263 super alloy with a multilayer CVD insert. Taguchi’s L-27 orthogonal array is used plan the experiments. Effect of input parameters viz. cutting speed (N), cutting feed (f), depth of cut (d) are studied on responses viz. surface roughness (SR), nose wear (NW) and cutting forces (F) under hybrid cryogenic (direct+indirect) machining environment. A scanning electron microscope (SEM) analysis is carried out to explore the post-machining outcomes on the performance measures. The multiple responses are converted in to single response and ranked according to Taguchi based gray relational grade (TGRG). Feed rate (f) is found to be the most influential parameter from the analysis of variance of GRG. The means of GRG for each level of process parameters are used to improve the optimal process parameters further. Finally, the confirmative experiment is performed with these optimal set of process parameters which showed an improvement of 9.34% in the value of GRG. The proposed work can be beneficial to choose ideal process conditions to enhance the performance of turning operation.

Researchers have explored primary colour-geometric shape associations since Kandinsky's correspondence theory. However, there is a gap in the literature regarding interior colour applications on surface shapes. To address this gap, an online study was employed to gather data with one hundred participants who were asked to choose their preferred colours for shapes on bedroom walls with follow-up questions on the colour-shape semantic associations, their preference of colours and shapes on bedroom walls independently in addition to their favourite colour, their favourite shape, and colour-shape pairs without interior context. The results revealed that colour-shape preferences in interiors differ from those found in psychology studies, other colour applications on bedroom walls, and other preferences, indicating that colour preference is context-dependent. Interestingly, the most popular colour for surface shapes on bedroom walls is purple, followed by brown and blue. The study contributes to the existing literature by providing colour charts for bedroom applications for professionals in the industry, their clients/users, and future studies.

Three-Dimensional mesoporous TiO2 scaffolds of anatase phase possess inherent eximious optical behavior that are beneficial in designing photoelectrodes for solar energy conversion applications. However, substantial efforts have been devoted in maximizing the UV and/or visible light absorption efficiency, and suppressing the annihilation of photogenerated charged species in pristine mesoporous TiO2 structure for improved solar illumination conversion efficiencies. This study provides the fundamental insights into Mxene functionalized mesoporous TiO2 as photoelectrode for the first time. This novel combination of Mxene functionalized TiO2 electrodes with and without TiCl4 treatments have been successfully optimized to intensify the process of photon absorption, charge segregation and photocurrent, resulting in superior photoelectrode performance. The photocurrent measurements of prepared photoelectrodes are significantly enhanced upon increased contents of Mxene due to improved absorption efficiency within the visible region as verified by UV–Vis absorption spectroscopy. Moreover, as evident through structural analysis, the anatase phase of TiO2 is well grown due to increased contents of Mxene and post-deposition heat treatments. Consequently, an appreciable coverage of well-developed grains on FTO surface observed in SEM images. Thereby, the newly fabricated conductive mesoporous TiO2 photoelectrodes are potential candidates for photoinduced energy conversion and storage purposes.

A Invasive emerging pollutants from wastewater effluent discharge, such as dyes, pesticides, etc., pose a serious threat to the ecosystem. Advanced oxidation processes (AOPs) under visible light irradiation have emerged as a promising technology to overcome toxic and recalcitrant organic compounds. In this work, the impact of operational factors, including the concentration of Fe3+ or Fe2+, [H2O2], the molar ratio (Oxalate/ Fe3+ or Fe2+), and the initial pH, was studied to obtain high efficiency in the degradation and mineralization of such a food dye to reduce their pollution. The study deals with the comparison of the efficiency of UV, LED, and sunlight irradiation on the photocatalytic degradation of the dye using Fe3+/Lig and Fe2+/Lig complexes. The results showed that sunlight irradiation gave a very rapid kinetic and higher degradation efficiency of over 70%. The optimized conditions for the maximum elimination of the dye with a photocatalytic degradation efficiency (98%) and a mineralization rate of 96% were obtained with the Fe3+/Lig complex, based on the Box Benhken surface design analysis. In the presence of H2O2, the degradation reached an equilibrium stage after 15 min (97.57%) for the Fe(III)/Lig system. Moreover, the inhibition effect of inorganic ions on the photo-Fenton performance of Fe3+/Lig and Fe2+/Lig was studied. The study suggests that the use of nanocrystals of hematite as a Fenton reagent for treating textile effluents needs further investigation. The results showed that the proposed models were well-suited to batch treatment under sunlight. This study not only proposes a Fe3+/Lig and Fe2+/Lig system for the elimination of a food dye without adjusting the pH of the medium, but it also provides insight into the best source of light irradiation for the photocatalytic degradation process.

Face milling is a well known commercial process highly used in heavy industries that consumes high amount of power. Besides power issue, modern manufacturing industries are aiming for per part cost reduction keeping the product quality unimpaired. Unexpectedly if the part is rejected in any stage of manufacturing, the cost of manufacturing dramatically increases. Major cause of part rejection is excessive tool wear that imparts poor surface profile or catastrophic tool failure that causes adherence of broken tool debris onto machined surface. Furthermore, the tool wear is associated with sliding distance (frictional distance) and the tool life quantifies the cost of tools. As such, from the perspective of manufacturing industries it is imperative to optimize the surface quality parameter, cost of part, power consumption, and material removal – this is exactly what is accomplished here. By this work, it is possible to conserve power consumption, produce parts with lower cost, manufacture with uncompromising surface quality and enhanced material removal rate. Moreover, as intermediate factors of interest, the influences of sliding distance, tool life and tool flank wear on the overall machining performance are evaluated. The multi-objective optimization by Grey Relational Analysis (GRA) revealed that for improved product performance and fast manufacturing (case 1) optimum results are: feed per tooth fz = 0.25 mm/tooth, cutting speed vc = 392.6 m/min and cutting length l = 0.5 mm; for resource conservation (case 2) the optimum results are: feed per tooth fz = 0.125 mm/tooth, cutting speed vc = 392.6 m/min, cutting length l = 0.5 mm.

This paper studies the optimization method of pump hydraulic performance based on the response surface method. A parametric model of impeller and diffuser is established. Three-dimensional optimization is carried out on the basis of the initial model obtained by one-dimensional design method. We select the pump hydraulic efficiency and the head as objective function and constraint function. Response surface models are constructed to analyze the relationship between the objectives and the design variables, and the global optimization of hydraulic performance is realized. According to the internal flow characteristics of pump, this paper proposes the strategy of two steps optimization, which aims at meridional plane and blade shape, respectively, to solve the problem of large numbers of design parameters and computational cost. The optimization results show that the hydraulic efficiency of pump increased by 3.7%, and the head is nearly the same.

Hydraulic fracturing has enabled production from unconventional reservoirs in the U.S., but production rates often decline sharply, limiting recovery factors to under 10%. This study optimizes the CO2 huff-n-puff process for multistage-fractured horizontal wells in Wolfcamp A formation in the Delaware Basin. The potential for enhanced oil recovery and CO2 sequestration simultaneously was addressed using a coupled geomechanics-reservoir simulation. Geomechanical properties were derived from a 1D mechanical earth model and integrated into reservoir simulation to replicate hydraulic fracture geometries. The fracture model was validated using a robust production history matching. Fluid phase behavior analysis refined the equation of state, and 1D slim tube simulations determined a minimum miscibility pressure of 4300 psi for CO2 injection. After the primary production phase, various CO2 injection rates were tested from 1 to 25 MMSCFD/well, resulting in incremental oil recovery ranging from 6.3% to 69.3%. Different injection, soaking, and production cycles were analyzed to determine the ideal operating condition. The optimal scenario improved cumulative oil recovery by 68.8% while keeping the highest CO2 storage efficiency. The simulation approach proposed by this study provides a systematic workflow for evaluating and optimizing CO2 huff-n-puff in hydraulically fractured wells, enhancing the recovery factor of unconventional reservoirs.

Although the concept of additive manufacturing has been proposed for several decades, momentum of selective laser melting (SLM) is finally starting to build. In SLM, density and surface roughness, as the important quality indexes of SLMed parts, are dependent on the processing parameters. However, there are few studies on their collaborative optimization in SLM to obtain high relative density and low surface roughness simultaneously in the previous literature. In this work, the response surface method was adopted to study the influences of different processing parameters (laser power, scanning speed and hatch space) on density and surface roughness of 316L stainless steel parts fabricated by SLM. The statistical relationship model between processing parameters and manufacturing quality is established. A multi-objective collaborative optimization strategy considering both density and surface roughness is proposed. The experimental results show that the main effects of processing parameters on the density and surface roughness are similar. It is noted that the effects of the laser power and scanning speed on the above objective quality show highly significant, while hatch space behaves an insignificant impact. Based on the above optimization, 316L stainless steel parts with excellent surface roughness and relative density can be obtained by SLM with optimized processing parameters.

Silicon anodes have been considered one of the most promising anode candidates for the next generation of high-energy density lithium-ion batteries due to the high theoretical specific capacity (4200 mAh g-1) of Si. However, high lithiation capacity endows silicon anodes with severe volume expansion effects during the charge/discharge cycling. The repeated volume expansions not only lead to the pulverization of silicon particles and the separation of electrode materials from the current collector, but also brings rupture/formation of solid electrolyte interface (SEI) and also continuous electrolyte consumption, which seriously hinders the commercial application of silicon anodes. Structural design and optimization is the key to improving the electrochemical performances of silicon anodes, which has attracted wide attention and research in recent years. This paper mainly summarizes and compares the latest research progress for the structural design and optimization of silicon anodes.

Abstract: High step-up voltage gain nonisolated DC-DC converter have attracted much attention in photovoltaic, fuel cells and other renewable energy system applications. In this paper, by combining input current ripple-free boost cell with coupled-inductor voltage-doubler cell, an input current ripple-free high voltage gain nonisolated converter is proposed. In addition, passive lossless clamp circuit is adopted to recycle the leakage inductor energy and to reduce the voltage spike across the power switch. By utilizing voltage-doubler cell consisting of diode and capacitor, the voltage stress of switch is further reduced and the resonance between the leakage inductor and the stray capacitor of the output diode is eliminated. A low switch-on-resistance low-voltage-rated MOSFET can therefore be employed to reduce the conduction loss and cost. The reverse recovery loss of output diode is reduced, and the efficiency of converter can be improved. Furthermore, the proposed converter can achieve nearly zero input current-ripple and make the design of electromagnetic interference (EMI) filter easy. Steady state analysis and operation mode of the converter is performed. Finally, experimental results are presented to verify the analysis results of the proposed converter.

The stability of the filling roof as an important bearing unit in the stope of the access stope in the filling mining method is of great significance to guarantee the safe and efficient production of the mine. Arrangement of mining approach in downward cemented filling stope is the key factor af-fecting stability of filling body roof. Based on combination of laboratory test, theoretical analysis and numerical simulation, the influence of different mining approach arrangement on stability of filling body roof is analyzed. The weak filling surface is formed between adjacent mining paths. The mechanical strength of the weak filling surface is significantly reduced by laboratory experiments. The relationship between distribution of the weak filling surface, azimuth angle and stability of filling roof is further studied by numerical simulation. The results show that the stability of the filler roof is the best when the upper and lower stratified mining approach is arranged vertically.

The overall cost of a hydropower plant is mainly due to the expenses for civil works, mechanical equipment (turbine and control units) and electrical components. The goal of a new draft tube design is to obtain a geometry that reduces investment costs, especially the excavation ones, but the primary driver is to increase the overall machine efficiency allowing for reduced payback time. In the present study, an optimization study of the elbow-draft tube assembly of a Kaplan turbine was conducted. A CFD model for the complete turbine has been developed and validated; next, an optimization of the draft tube alone was performed using a Design of Experiments technique; finally, several optimum solutions for the draft tube were obtained using a Response Surface technique aiming at maximizing pressure recovery and minimizing flow losses. A selection of optimized geometries was subsequently post-checked using the validated model of the entire turbine and a detailed flow analysis on the obtained results could make it possible to provide insight into the improved designs. It was observed that efficiency could be improved by 1% (in relative terms), and the mechanical power increased by 1,8% (in relative terms) with respect to the baseline turbine.

During 2021 and 2022 summers, we measured the total and dissolved (< 0.45 mm) concentration of 25 elements in Utah Lake using Inductively Coupled Plasma Optical Emission Spectrometry (ICP-OES). Utah regulates twelve of these elements. ICP-OES sensitivity is at the ppb-level but is not the approved regulatory method. All regulations are for dissolved concentrations; except aluminum (Al) and phosphorus (P) which are for total recovery. We found total Al concentrations above allowable, but dissolved concentrations were well below allowable concentrations. We attribute high total concentrations to suspended clays. Dissolved copper (Cu) concentrations were below regulatory levels in 2021, but some samples were above regulatory levels in 2022. This could be related to the use of Cu-based algaecide treatments, or from other sources. Lead (Pb) data were inconclusive; dissolved Pb concentrations were well below the acute (1-hour average) limit, but the chronic concentration limit (4-hour average) is below the ICP-OES minimal detection limit. Arsenic (As) concentrations exhibit a seasonal trend that we attribute to groundwater inflows. This ppb-level study provides insight into regulated elements in Utah Lake previously not available due to the high sensitivity of the method and measurements of both total and dissolved concentrations.

The present study propose an innovative turn-boring operation method and focuses on finding optimal turn-boring process parameters for 15-5PH Stainless steel by considering multiple performance characteristics using Taguchi orthogonal array with the grey relational analysis, the effect of machining variables such as concentration of cutting fluid , temperature of cutting fluid , feed rate, depth of cut and cutting speed are optimized with considerations of multiple performance characteristics namely surface roughness, roundness error and material removal rate, the optimal values were found out from the Grey relational grade. The result of the Analysis of Variances (ANOVA) is shown that the most significant factor is cutting speed, followed by feed rate, concentration of cutting fluid, radial depth of cut and temperature of cutting fluid. Finally, confirmation tests were carried out to make a comparison between the experimental results and developed model. Experimental results have shown that machining performance in the turn-boring process can be improved effectively through this approach.

The grinding process by friction at the micro-scale in a mill with stones is considered a variable combination of contacts: with two-body (the asperities of lower millstone in direct contact with the asperities of upper millstone) and the three-body (micro-particles of ground seeds trapped between the asperities of lower and the upper stones of the mill). Three elements are described: (1) the mechanic contact of the asperities of the lower and upper millstone, to predict pressures on asperities, by modeling; (2) tests on a millstone sample covered with grinding particles, and (3) tests on a wafer sample formed by the millstones with the grinding particles between them. The paper highlights the combined effects of the micro-scale friction by individual measurements and to sum these effects an analytical model was used, and to validate the model, several experiments were performed. A suitable grind by friction assumes the grain’s movement and the interaction between the seeds and solid surfaces and is highlighted through theoretical and experimental studies. Topography analysis of the surface of the millstones revealed the model of microscopic frictional force. Endpoint measurements (the traces of the surface topography evolution), enable model verification in the grinding process.

The object of study is a transversely bent triangular plate made of orthotropic material fixed along the edges of the plate under the action of a uniformly distributed load. Fourth-order differential equilibrium equations with variable orthotropy parameters were used. The equations were approximated by finite differences for a grid of scalene triangles. This type of mesh accurately describes the boundary contour of the triangular-shaped plates. The boundary conditions for the mesh consider the orthotropy of the plate material. Seven standard finite-difference equations have been developed considering the boundary conditions along the three edges of the plate and the presence of three angles of an irregularly shaped triangle. A finite difference matrix is obtained. The matrix structure makes calculating a triangular plate at different base angles possible. The boundary conditions were varied in the form of rigid or hinged support of triangular plates. The calculation method considers the orthotropic parameters of the material in two mutually perpendicular planes. The adaptation of the numerical method to the calculation of orthotropic plates of arbitrary shape is described. Relationships are given for determining the rigidity characteristics of orthotropic materials. An algorithm for simple engineering calculation of triangular orthotropic plates is proposed, which makes it possible to perform accurate calculations in variant design.

In this study, AlSi12 alloy was fabricated using the selective laser melting (SLM) technique to produce high density components with complex and customized parts for railway applications. Nonetheless, the production of dense samples necessitates the optimization of production process parameters. As a statistical design of experimental technique, the response surface methodology was used to optimise different combination of SLM parameters. The results were analysed using analyse of variance (ANOVA) and the signal-to-noise(S/N) ratios. The relationship between the hardness response to the process parameters (scanning speed and lase power) for determining the optimal processing conditions were examined. A hardness value of 133 HV was obtained. The process parameters were successfully optimized and the relationship between the parameters and the structures of the fabricated samples were reported.

Geopolymer cement has been popularly studied nowadays compared to ordinary Portland cement because it demonstrated superior environmental advantages due to its lower carbon emissions and waste material utilization. This paper focuses on the formulation of geopolymer cement from nickel-laterite mine waste (NMW) and coal fly ash (CFA) as geopolymer precursors, and sodium hydroxide (SH) and sodium silicate (SS) as alkali activators. Different mix formulations of raw materials are synthesized to produce a geopolymer based from an I-optimal design and obtained different compressive strengths. A mixed formulation of 50% NMW and 50% CFA, SH-to-SS ratio of 0.5, and an activator-to-precursor ratio of 0.429 yielded the highest 28-day unconfined compressive strength (UCS) of 22.10 ± 5.40 MPa. Furthermore, using an optimized formulation of 50.12% NMW, SH-to-SS ratio of 0.516, and an activator-to-precursor ratio of 0.428, a UCS value of 36.30 ± 3.60 MPa was obtained. The result implies that the synthesized geopolymer material can be potentially used for concrete structures and pavers, pedestrian pavers, light traffic pavers, and plain concrete.

An increasing number of aircraft is equipped with wing tip devices, which either are installed by the aircraft manufacturer at the production line or are retrofitted after the delivery of the aircraft to its operator. Installation of wing tip devices has not been a popular choice for regional turboprop aircraft and the novelty of the current study is to investigate the feasibility of retrofitting the British Aerospace (BAe) Jetstream 31 with an appropriate wing tip device (or winglet) to increase its cruise range performance, taking also into account the aerodynamic and structural impact of the implementation. To the best of the knowledge of the authors, no previous study exists which has attempted to assess the winglet retrofit of an existing aircraft type of similar size and operating profile. The optimal winglet design achieved a 2.38% increase of the maximum range by reducing the total drag by 1.19% at a mass penalty of 3.25%, as compared with the baseline aircraft configuration. Other designs were found to be more effective in reducing the total drag, but the structural reinforcement required for their implementation outweighed the achieved performance improvements. Since successful winglet retrofit programs for typical short to medium range narrow body aircraft report even more than 3% of block fuel improvements, undertaking the project of installing an optimal winglet design to the BAe Jetstream 31, should also consider a Direct Operating Cost (DOC) assessment on top of the aerodynamic and structural aspects of the retrofit.

Machining titanium alloy (Ti6Al4V) used in orthopedic implants by conventional metal cutting processes is challenging due to excessive cutting forces, low surface integrity and tool wear. To overcome these difficulties and for ensuring high-quality products, various industries employ wire electrical discharge machining (WEDM) for precise machining of intricate shapes in titanium alloy. The objective is to make WEDM machining parameters as efficient as possible for machining the bio-compatible alloy Ti6Al4V using box-behnken design (BBD) and Non-dominated Sorting Genetic Algorithm II (NSGA II). A quadratic mathematical model is created to represent the productivity and the quality factor (MRR and surface roughness) in terms of varying input parameters, such as pulse active (Ton) time, pulse inactive (Toff) time, peak amplitude (A) current and applied servo (V) voltage. The established regression models and related prediction plots provide a reliable approach for predicting how the process variables affect the two responses viz MRR and SR. The effects of four process variables on both the responses were examined, and the findings revealed that the pulse duration and voltage has a major influence on the rate at which material is removed (MRR) whereas pulse duration influence quality (SR).  The trade-off between MRR and SR, when significant process factors are included emphasizes the need for a reliable multi-objective optimization method. The intelligent metaheuristic optimization method named non-dominated sorting genetic algorithm II (NSGA II) is utilized to provide pareto optimum solutions in order to achieve high material removal rate (MRR) and low surface roughness (SR).

Surface acoustic wave (SAW) is effective for the manipulation of fluids and particles in microscale. The current approach of integrating interdigitated transducers (IDTs) for SAW generation into microfluidic channels involves complex and laborious microfabrication steps. These steps often require the full access to clean room facilities and hours to align the transducers to the precise location. This work presents an affordable and innovative method for fabricating SAW-based microfluidic devices without the need of clean room facilities and alignment. The IDTs and microfluidic channels are fabricated in the same process and thus precisely self-aligned in accordance with the device design. With the use of the developed fabrication approach, a few types of different SAW-based microfluidic devices have been fabricated and demonstrated for particle separation and active droplet generation.

Solar energy is one of the most important renewable energy sources for many settings, such as households, solar-powered vehicles, power grid support, etc. However, the amount of solar energy produced is directly proportional to the surface area of the solar panel exposed to the sun rays, and so the challenges arise for the space required to install solar panels in order to get maximum area coverage of sun radiation energy absorption in constricted spaces such as vehicles powered by solar, small residential apartments, etc. The challenge with solar energy is that once a plate is installed, the space under it or above it cannot be used for another solar panel installation. This is due to the fact that the shadow cast by the above solar panel or structure prevents sun rays from reaching the below solar panel. The introduction of flexible solar panels that can take on any shape has given us the opportunity to explore the possibility of maximising solar plate surface area using surface manifold techniques. In this optimisation study, the constraint is that we have a space with fixed dimensions of length, width, and height, and the objective is to maximise the surface area of the panel within the given space dimensions to maximise solar energy absorption. Thus, this paper then proposes curving the panel surface and/or protruding the surfaces of the panel using the concept of a topology surface manifold to maximise the surface area: Protruding panel surface with shapes such as pyramidal, cone, hemisphere, sinusoidal wavy curve, etc. are analysed to check if the panel surface increases at all. The geometrical design result shows that the panel surface can increase by more than 20%. Although this paper only presents concept work and details of experimental design are yet to be performed, it should also be noted that curving surfaces have drawbacks, such as some protruding parts of solar panels when the plate is tilted, not facing the sun directly, which may cast shadows on parts of the solar panel, causing hindrance.

Surface Plasmon Resonance (SPR) based sensors have the advantage of being label-free, enzyme-free and real-time. However, their spreading in multidisciplinary research is still limited and almost confined to prism-coupled devices. Plasmonic gratings, combined with a simple and cost-effective instrumentation, have been poorly developed compared to prism-coupled system mainly due to their lower sensitivity. Here we describe the optimization and signal enhancement of a sensing platform based on phase-interrogation method, which entails the exploitation of a nanostructured sensor. This technique is particularly suitable for integration of the plasmonic sensor in a lab-on-a-chip platform and can be used in a microfluidic circuit to ease the sensing procedures and limit the injected volume. The careful optimization of most suitable experimental parameters by numerical simulations leads to a 30 to 50% enhancement of SPR response, opening new possibilities for applications in the biomedical research field while maintaining the ease and versatility of the configuration.

With increasing air and sea temperatures, the thermodynamic environments over the oceans become more favourable for the development of intense tropical cyclones (TCs) with rapid intensification (RI). In fact, the number of TCs undergoing RI is rising (Zhao, et al., 2018; Bhatia, et al., 2019; Song, et al., 2020; Hong & Wu, 2021; Liu, et al., 2022). RI over coastal sea areas before landfalling is particularly impactful and threatening to coastal lives and properties. There have been studies showing that offshore areas within 400 km of the coastline have experienced a significant increase in RI events with the count tripling from 1980 to 2020 (Li et al., 2023). The south China coastal region consists of highly densely populated cities especially the Pearl River Delta (PRD) region. Intense TCs maintaining its strength or RI of TCs close to the coastal region presents substantial forecasting challenges. This study investigates the effect of sea surface and subsurface temperature and salinity on the intensification of five TCs, namely Super Typhoons Hato in 2017 and Mangkhut in 2018, Typhoon Talim, Super Typhoon Saola and Severe Typhoon Koinu in 2023, which significantly affected the south China coastal region and triggered high TC warning signals in Hong Kong. The analysis utilized the Hong Kong Observatory (HKO) TC track and intensity data, along with the sea temperature and salinity profiles generated using the China Ocean ReAnalysis version 2 (CORA2) of the National Marine Data and Information Service (NMDIS) of China. While high sea surface temperature (SST) of 30°C or above, low surface sea surface salinity (SSS) of 34 psu or below, and strong salinity stratification of at least 0.8 psu per 100 m depth may offer useful hints for predicting RI, they are part of a broader set of contributing factors. This study represents the initial documentation of sub-surface salinity's impact on intense TCs over the South China Sea (SCS) in recent years and will encourage further research to refine forecasting RI of TCs before making landfall near PRD taking into account the effect of freshwater from the Pearl River.

In this study, the coating order of two monomers in the shell polymerization process of core–shell nanoparticles was altered to facilitate easy coating and optimize the properties of the coated surface to simplify the additional coating formulation process. To obtain a glass transition temperature suitable for coating, a core was synthesized by the copolymerization of an acryl monomer. A perfluoro monomer and silane monomer were additionally added to synthesize nanoparticles exhibiting both water–oil repellency and anchoring properties. In order to realize various surface properties, the nanoparticles underwent surface modification and cellulose fiber was introduced. Through the various data described in this text, the surface properties improved with the order of introduction of the two monomers.

To study the fermentation process of biocatalyzing decanoic acid to synthesize trans-2-decenoic acid, this study was based on the engineering E.coli constructed in the laboratory in the early stage and studied the effect of seed liquid culture time, culture temperature, inoculum amount, induction temperature, dissolution effects of substrate solvent, metal ions, and substrate loading on the yield of trans-2-decenoic acid. Based on single-factor experimental optimization, the Box–Behnken design was used to conduct response surface testing using the substrate feeding concentration, inducer concentration, and MnCl2 concentration as response variables and trans-2-decenoic acid production as the response value. The optimal fermentation process was determined through experiments: seed culture time 20 h, culture temperature 37°C, inoculation amount 1%, induction temperature 30°C, substrate flow amount 0.15 g/L, inducer concentration 5.60 g/L, MnCl2 concentration was 0.10 mM. Under these conditions, the average production of trans-2-decenoic acid was 1.982 ± 0.110 g/L. Compared with the basic LB medium, the production of trans-2-decenoic acid increased by 1.042 g/L; compared with the previous period, the yield of trans-2-decenoic acid studied increased by 1.501 ± 0.110 g/L, which provides a reliable basis for further research on the fermentation process of biocatalytic decanoic acid synthesis of trans-2-decenoic acid.

Automated controlling the harvesting systems can significantly increase the efficiency of the agricultural practices and prevent food wastes. Modeling and improvement of the combine harvester can increase the overall performance. Machine learning methods provide the opportunity of advanced modeling for accurate prediction of the highest performance of the machine. In this study, the modeling of combine harvesting id performed using radial basis function (RBF) and the hybrid machine learning method of adaptive neuro-fuzzy inference system (ANFIS) to predict various variables of the combine harvester for the optimal performance. Response surface methodology (RSM) is also used to optimize the models. The comparative study shows that the ANFIS method outperforms the RBF method.

In the case of a Cu-Mo-W polymetallic ore, the wastewater from the scheelite cleaning flowsheet contains large amounts of residual flocculants and metal ions, and the separation of chalcopyrite and molybdenite require a large number of environmentally harmful depressants. Therefore, it is necessary to find new methods to reduce the environmental and cost pressures of wastewater treatment and the use of depressants. In this work, the flotation wastewater from scheelite cleaning flowsheet for the separation of chalcopyrite and molybdenite by selective surface passivation was investigated for the first time. Flotations of single minerals and artificially mixed minerals with or without immersion pretreatment in the presence and absence of aeration were performed. The results showed that pulp pH had no effect on the flotation of either mineral, and a molybdenite recovery of 93.22% with chalcopyrite recovery of 10.77% was achieved under the conditions of 10 days of immersion pretreatment with aeration, 350 mg/L of kerosene, and 100 mg/L of MIBC. By combining the electrochemical cyclic voltammetry analysis and characterization by XRD and SEM, the selective surface passivation mechanism of chalcopyrite was discussed, which could be due to the coverage of the insoluble oxidation products, especially jarosite. This work has simultaneously achieved the depressant-free flotation separation of molybdenite and chalcopyrite and the reuse of scheelite flotation wastewater, which is of great significance for environmental protection and cost saving.

Strip steel surface defect recognition research has important research significance in industrial production. Aiming at the problems of defect feature extraction difficulty, slow detection speed and insufficient dataset, YOLOv5 is improved on the basis of YOLOv5, and YOLO-LFPD (Lightweight fine particle detection) model is proposed. By introducing the RepVGG (Re-param VGG) module, the robustness of the model to the surface defect features of strip steel is enhanced, and the expressive ability of the model is improved. FasterNet is used to replace the backbone network, which ensures the accuracy and accelerates the inference speed, making the model more suitable for real-time monitoring. The use of pruning, GA genetic algorithm with OTA loss function method further reduces the model size while better learning the strip steel defect feature information, thus improving the generalisation ability and accuracy of the model. The experimental results show that the introduction of the RepVGG module and the use of FasterNet can well improve the model performance, with a reduction of 48% in the number of parameters, a reduction of 13% in the number of GFLOPs, an inference time of 77% of the original, and an optimal accuracy compared with the network models in recent years. The experimental results on the NEU-DET dataset show that the accuracy of YOLO-LFPD is improved by 3% to 81.2%, which is better than other models, and provides new ideas and references for the lightweight strip steel surface defect detection scenarios and application deployment.

In response to the structural optimization problem of PCB stator coreless disc motors, the orthogonal response surface method was used to optimize the motor structure, determine the basic parameters of the motor preliminarily, and conduct orthogonal experiments on the motor parameters based on the optimization design objectives, The optimization factors were the quantity of magnetic pole of the motor rotor, the ratio of main/auxiliary pole size, the thicknessof the permanent magnet, and the air gap length.The motor torque，the amplitude of magnetic density of the air gap and waveform distortion rateare used as optimization objectives. The motor parameters that make the motor torque reach the maximum, the air gap magnetic density maximum, and the waveform distortion rate minimum. Due to the use of PCB plates instead of motor stator cores in PCB coreless disc motors,The service life of the PCB board during motor operation will be reduced with the temperature rise generated by the stator winding To solve this problem, the response surface analysis of the motor is carried out to reduce the temperature rise of the stator windings during the operation of the motor. PCB board and stator winding are the main factors affecting the temperature rise of the motor.Taking the thickness of the PCB board, the hole diameter on the board, and the uneven width of the stator winding as optimization factors, the motor parameters with the lowest temperature rise of the motor winding are obtained. Simulation analysis is conducted using Ansys/Maxwell software, and the results prove the feasibility of optimization.

Part II, like Part I, discusses geometry, kinematics and statics in detail without taking into account power losses in meshing. The main goal of Part II, however, is to prove that there are complex and structurally coupled planetary gear systems, i.e. containing a closed circuit in which no circulation of power flow is generated. The power flow analysis is also carried out using the direct method, with a slight modification in the way of writing the equations identifying active and passive gears, i.e. at the same time the directions of power flow on all transmission paths. The analysed planetary gear system (PGS) is characterised by mobility equal to 1, i.e. single degree of freedom (DoF). It consists of three subsystems in the form of the 2KH type planetary units connected in series-parallel, specially selected to demonstrate the thesis of this paper. It consists of three subsystems in the form of single planetary subsystems of the 2KH type connected series-parallel, specially chosen to illustrate the thesis of this paper.

Inverse gas chromatography at infinite dilution was used to determine the surface thermodynamic properties of silica particles and PMMA adsorbed on silica, and more particularly, to quantify the London dispersive energy γsd, the Lewis acid γs+ and base γs- polar surface energies of PMMA/silica composites as a function of the temperature and the recovery fraction θ of PMMA. The polar acid–base surface energy γsAB and the total surface energy of the different composites were then deduced as a function of the temperature. In this paper, the Hamieh thermal model was used to quantify the surface thermodynamic energy of poly methyl methacrylate (PMMA) adsorbed on silica particles at different recovery fractions. A comparison of the new results was carried out with those obtained by applying other molecular models of the surface areas of organic molecules adsorbed on the different solid substrates. An important deviation of these molecular models from the thermal model was proved. The determination of γsd, γs+, γs-, and γsAB of PMMA in both bulk and adsorbed phases showed an important non-linearity variation of these surface parameters as a function of the temperature. The presence of maxima in the curves of γsd(T) highlighted the second order transition temperatures in PMMA showing beta-relaxation, glass transition and liquid-liquid temperatures. These three transition temperatures depended on the adsorption rate of PMMA on silica. The proposed method gave a new relation between the recovery fraction of PMMA and its London dispersive energy showing an important effect of the temperature on the surface energy parameters of adsorption of PMMA on silica. A universal equation relating γsd(T,θ) of the systems PMMA/silica to the recovery fraction and the temperature was proposed.

With continuous increase in integration of the semiconductor devices, the requirements on size accuracy and surface quality of the etched lead frame are higher. The etchant is a key factor on etching process and etched surface quality, while effects of the difference in etchants on microscopic etched surface morphology of the Cu alloy have not been directly studied. In this study, the aqua regia, acidic FeCl3 and CuCl2 solutions were used as etchants, and the CuCrSn alloy specimens with different microstructure were etched and characterized. The results show that the etching rate in aqua regia is high, and the grain orientation, grain boundary (GB) and dislocation have significant influence on the local etching rate. The preferential etching of some atomic planes forms steps between grains with different orientations, and the preferential etching around the GB and dislocation group forms grooves, resulting in high surface roughness. For etching of the FeCl3 and CuCl2 etchants, the steps and grooves become blurred, and almost invisible on the surface etched by the CuCl2 etchant, thus the surface roughness is much lower. The CuCrSn alloy surface etched by the aqua regia is clean, with little Cr-rich particles, while high density Cr-rich particles are remained on the surfaces etched with the FeCl3 and CuCl2 etchants. For the same kind of etchant, the ion concentration can affect the etching mechanism and etching surface morphology.

The present study employed a modifed QuEChERS method to systematically analyze the presence of fifteen Quinolones and seven Tetracyclines antibiotic residues in local animal food. Additionally, a multi-level-four-factor Box-Behnken design (BBD) within the framework of Response surface methodology (RSM) was utilized to evaluate the various factors affecting the detection efficiency of the sample pretreament procedure. The optimization was performed by Design Expert®, the factors including volume of the acetonitrle, the addition of formic acid, the duration of extract and the addition of EDTA were combined to experiment design until reach an optimal solution. Finally, the sample test was conducted by ultra-high performance liquid chromatography-quadrupole-linear ion trap mass spectrometry in both multiple reaction monitoring (MRM) and enhanced product ion (EPI) scan modes on a QTRAP® 5500 instrument. The overall average recoveries from actual samples fortified with 22 antibiotics at three levels ranged from 74.7 to 122.6% based on the use of matrix-fortified calibration with the variation ranging from 2.1 to 18.2% (n=6). The limits of detection and quantification were 0.3 μg kg-1 and 1.0 μg kg-1, respectively.

The infrared (IR) satellite remote sensing of sea surface skin temperature (SSTskin) is challenging in the northern high latitude region, especially in the Arctic because of its extreme environmental conditions, and thus the accuracy of SSTskin retrievals is questionable. Several Saildrone uncrewed surface vehicles were deployed at the Pacific side of the Arctic in 2019, and two of them, SD-1036 and SD-1037, were equipped with a pair of IR pyrometers on the deck whose measurements have been shown to be useful in the derivation of SSTskin with sufficient accuracy for scientific applications, providing an opportunity to validate satellite SSTskin retrievals. This study aims to assess the accuracy of MODIS-retrieved SSTskin from both Aqua and Terra satellites by comparisons with collocated Saildrone-derived SSTskin data. The mean differences in SSTskin from the SD-1036 and SD-1037 measurements are different by ~0.4 K, largely resulting from differences in the atmospheric conditions experienced by the two Saildrones. The performance of MODIS on Aqua and Terra in retrieving SSTskin is comparable. Negative brightness temperature (BT) differences between 11 μm and 12 μm channels are identified as being physically based, but are removed from the analyses as they present anomalous conditions for which the atmospheric correction algorithm is not suited. Overall, the MODIS SSTskin retrievals show negative mean biases, -0.234 K for Aqua and -0.295 K for Terra. The variations in the retrieval inaccuracies show an association with diurnal warming events in the upper ocean from long periods of sunlight in the Arctic. Also contributing to inaccuracies in the retrieval is the surface emissivity effect in BT differences characterized by the Emissivity-introduced BT difference (EΔBT) index. This study demonstrates the characteristics of MODIS-retrieved SSTskin in the Arctic, at least at the Pacific side, and underscores that more in situ SSTskin data at high latitudes are needed for further error identification and algorithm development of IR SSTskin.

The movement of liquid droplets on the energy gradient surface has attracted extensive attention. Inspired by biological features in nature, such as the periodic spindle-shaped nodes in spider silks and conical-like barbs of cacti, the structure-property-function relationship of multifunctional gradient surfaces. In this study, a series of specific patterns are fabricated by 3D printing technology, followed by modification via the atmospheric pressure plasma treatment and liquid phase chemical deposition, resulting in enhancing the ability of water droplets of 5μL to travel 18.47mm on a horizontal plane and 22.75mm against gravity up to 20° tilting angle. Additionally, analysis techniques have been employed including contact angle analyzer, ESCA and laser confocal microscope to evaluate the sample performance. This work could further be applied to many applications related to microfluidic devices, drug delivery and water/fog collection.

Friction stir welding (FSW) is a solid state welding process for joining metallic alloys and dissimilar metals. It has emerged as an alternative technology for welding high strength alloys that are difficult to join with conventional techniques. FSW is used to produce products with better mechanical properties. Now a days aluminum alloys have been widely used in several industrial applications such as aerospace, marine, automobile and commercial applications due to their light weight structure, better mechanical properties and high corrosion resistance.In this work, three welding parameters such as spindle speed, welding speed and plunge depth were considered for friction stir welding. FSW was carried out between dissimilar aluminum alloy plates (AA6061 and AA 8011) to produce butt joint.A Box-Behnken design with three factors and three levels was chosen to minimize the number of experimental conditions .The tensile strength and hardness of the welded regions were evaluated. The optimum level settings and the major parameters that influence the joint strength were obtained by Box-Behnken design.

In order to improve the yield of the therapeutic agent N-methylsansalvamide (SA), optimization of stationary liquid fermentation conditions was carried out on an endophytic strain, Fusarium sp. R1, at flask level. Using a One-Factor-At-a-Time approach, the fermentation conditions for SA production were determined as follows: fermentation time of 13 d, 24 oC, initial pH of 6.5, seed age of 24 h, inoculum size of 5.0% (v/v), loading volume of 50% (v/v), 20.0 g/L salinity, and sucrose, tryptone, and yeast extract were found to be the best sources of carbon and nitrogen. Using response surface methodology, the optimal medium compositions consist of 22.5 g/L sucrose, 16.5 g/L tryptone, and 0.024 g/L yeast extract. Verification tests suggested that the SA yield under these optimal conditions reached up to 536.77 ± 2.67 mg/L, which was increased by almost ten times the initial yield (54.05 ± 3.45 mg/L). The findings indicate that a high SA production yield can be achieved by static culture of strain R1 under the proper fermentation conditions using a low-cost medium. This study paves the way towards industrial-scale SA production by strain R1 for new drug development.

Slot-die coatings are advantageous when used for coating large-area flexible devices; in particular, the coating width can be controlled, and simultaneous multi-layer coatings can be processed. Till date, the effects of ink widening and coating gap on the coating thickness have only been considered in a few studies. To this end, we developed two mathematical models to accurately estimate the coating width and thickness considering these two effects. We used root mean square deviation (RMSD) to experimentally verify the developed method. The coating width was seen to increase and the coating thickness was seen to decrease when the coating gap was increased. Experimental results showed that the estimation performances of the coating width and thickness models were as high as 98.46 % and 95.8 %, respectively. We believe that the developed models can be useful for determining the coating conditions according to the ink properties to coat a functional layer with user-defined widths and thicknesses in both lab- and industrial-scale roll-to-roll slot-die coating processes.

We investigate molecular beam epitaxy growth conditions of micrometers-thick In0.52Al0.48As designed for waveguide of InGaAs/InAlAs/InP quantum cascade lasers. Effect of growth temperature and V/III ratio on the surface morphology and defect structure were studied. The growth conditions which were developed for the growth of cascaded In0.53Ga0.47As/In0.52Al0.48As active region, e.g. growth temperature of TG=520°C and V/III ratio of 12, turned out to be not optimum for the growth of thick In0.52Al0.48As waveguide layers. It has been observed that after exceeding ~1µm thickness the quality of In0.52Al0.48As layers deteriorates. The in-situ optical reflectometry showed increasing surface roughness caused by defect forming, which was further confirmed by High Resolution X-Ray reciprocal space mapping, optical microscopy and atomic force microscopy. The presented optimization of growth conditions of In0.52Al0.48As waveguide layer led to the growth of defect free material, with good optical quality. This has been achieved by decreasing the growth temperature to TG=480 °C with appropriate increasing V/III ratio. At the same time the growth conditions of the cascade active region of the laser were left unchanged. The lasers grown using new recipe have shown lower threshold currents and improved slope efficiency. We relate this performance improvement to reduction of the electron scattering on the interface roughness and decreased waveguide absorption losses.

The process of preparing anti-glare thin films by spray-coating silica sol-gel to soda-lime glass was exclusively and statistically studied in this paper. The effects of sol-gel deliver pressure, air transport pressure, and spray gun displacement speed on the gloss, haze, arithmetic mean surface roughness, and total transmittance light were analyzed. The experimental results indicate that the factors of sol-gel deliver pressure, air transport pressure, and displacement speed exhibit significant effect on the haze, gloss, and Ra. In contrast, the variation of total transmittance light with these three factors are insignificant. Because the anti-glare property is predominantly determined by low gloss and high haze, therefore, we aim to minimize gloss and maximize haze to achieve high anti-glare. Central composite design and response rurface methodology are employed to analyze the main and interaction effects of the three factors through quadratic polynomial equations, which are confirmed by the analysis of variance and R². The response surface methodology predict the lowest gloss and highest haze are 9.2 GU and 57.0%, corresponding to the sol-gel deliver pressure, air-transport pressure, and displacement speed of 250 kPa, 560 kPa, and 140 mm/s, and 340 kPa, 620 kPa, and 20 mm/s, respectively. Comparing the predicted optimal data with the real experimental results validates the applicability of the mathematical model. This study provides an important basis for the subsequent production of anti-glare glass with different specifications to satisfy the market demand.

In this paper, we present an experimental procedure to enhance the dimensional accuracy of fabrication via Stereolithography (SLA) of features at the micro-scale. Using a custom benchmark part, deviations in feature dimensions (micro-pores diameters and depths) were detected and measured by confocal microscopy. Samples characterization and experimental observations allowed the identification of inaccuracy sources, mainly due to the laser beam scanning strategy and to the incomplete removal of uncured liquid resin in post-processing (i.e., IPA washing). As a technology baseline, the measured dimensional errors on pores diameters were up to -46%. A compensation method of the nominal laser spot diameter (85m) was defined and implemented resulting in relevant improvements in dimensional accuracy of 9.8% and 11.3% on full-open pores diameter and depth, respectively. Further investigation was performed on a customized test part to adjust the calibration procedure. The measurements revealed that the estimate of the laser beam spot size is 968m. Measurements on micro-pores having different sizes revealed that a constant compensation parameter (i.e., C=85, 96, 120m) is not fully effective at the micro-scale, where average errors still remain at -24%, -18.8%, and -16% for compensations equals to 85, 96 and 120m, respectively. A further experimental campaign allowed the identification of an effective nonlinear compensation law where the compensation parameter depends on the micro-feature size C= f (D). Results show a sharp improvement in dimensional accuracy on micro-pore fabrication, with errors consistently below +8.2%. The proposed compensation method can be extended for the fabrication of any micro-features without restrictions on the specific technology implementation. Concerning the inaccuracy introduced by the laser path, experimentation with a customized part allowed the optimization of the part orientation to reduce the errors and their differences along the X and Y machine axes.

Due to its potential harm to space payload, microwave corona breakdown of microstrip circuits has attracted much attention. This work describes an efficient way to suppress corona breakdown. Since corona breakdown threshold is determined by the highest electric field intensity at the surface of microstrip circuits, lacquer coating with thickness of tens of microns is sprayed on the top of microstrip circuits. The applied dielectric coating is used to move the discharge location away from circuit’s surface which is equivalent to reduce the highest electric field intensity on the in-terface of solid/air of the circuit and thus results into higher breakdown threshold. Two designs of classic coupled-line band-pass filter were used for verification. Corona experimental results at 2.5 GHz show that, in the interested low pressure range (100 to 4500 Pa), 5.3 dB improvement of mi-crowave corona breakdown threshold can be achieved for a filter with narrowest gap of 0.2 mm while its electrical performances like insertion loss, Q-factor are still acceptable. A threshold improvement prediction method is also presented and validated.

A detailed review of the scientific literature was undertaken to examine the most recent developments in plasma processing in the field of medicine. The first part of the review includes a detailed breakdown of the different types of coatings that can be applied onto medical devices using plasma, with a specific focus on antimicrobial surfaces. The developments during 2023 in plasma deposited biocompatible, drug delivery and adhesive coatings are described and specific applications in additive manufacturing are highlighted. The use of plasma and plasma activated liquids as standalone therapeutics continues to evolve and pertinent advances in this field are described. In addition, the combination of plasma medicine with conventional pharmaceutical interventions was reviewed and key emerging trends were highlighted, including the use of plasma to enhance drug delivery directly into tissue. The potential synergies between plasma medicine and chemotherapeutics for oncology and infection treatment is a growing area and recent advancements are noted. Finally, the use of plasma to control excess antibiotics and to intentionally degrade such materials in waste streams is described.

Nowadays, Multi-needle electrospinning has used to be an efficient method for producing nanofiber membranes. But in the process, the fluctuation errors in electrospinning fluid flow rate have directly influence the membrane quality, which bringing instability and still have not been solved yet. For finding out the solution to the inaccurate flow control in multi-needle, it is necessary to develop a multi-stage flow runner spinneret for large-scale production of nanofiber membrane. At first, the paper uses the finite element software COMSOL to numerically simulate the polymer flow in the runner of spinneret. Based on it, the velocity field distribution curve was draw and the velocity instability coefficient of the polymer flow was attained, which are providing theoretical guidance for the optimal design of spinneret. Next, the response surface analysis method (RSM) was used to establish a regression model between the average diameter of the nanofiber membrane and the process parameters. Then, above regression model used to perform variance data processing between the average diameter and the process parameter configuration. After that, the 2D and 3D response surface profiles and the significance analysis were completed. Finally, the stability of the nanofibers production was improved, which attained the optimal adjustment of process configuration in multi-needle electrospinning.

The present study propose an innovative turn-boring operation method and focuses on finding optimal turn-boring process parameters for Ti-6Al-4V by considering multiple performance characteristics using Taguchi orthogonal array with the grey relational analysis, the effect of machining variables such as, feed rate, depth of cut and cutting speed are optimized with considerations of multiple performance characteristics namely surface roughness, roundness error, material removal rate and power consumption the optimal values were found out from the Grey relational grade. The result of the Analysis of Variances (ANOVA) is shown that the most significant factor is cutting speed, followed by feed rate, radial depth of cut. Finally, confirmation tests were carried out to make a comparison between the experimental results. Experimental results have shown that machining performance in the turn-boring process can be improved effectively through this approach.

Ice accumulation poses considerable challenges in transportation, notably in the domain of general aviation. The present study combines the strengths and limitations of conventional aircraft de-icing techniques with the emerging trend toward all-electric aircraft. The study aims to utilize laser-induced graphene (LIG) technology to create a multifunctional surface, seamlessly integrating hydrophobic properties with efficient electrical heating to mitigate surface icing effectively. We investigated the utilization of a 10.6 μm CO2 laser for direct writing on polyimide (PI), a widely-used insulating encapsulation material. From the thermomechanical perspective, our initial analysis using COMSOL Multiphysics software revealed that when the laser power P exceeds 5 W, the PI substrate experience ablative damage. The experimental results show that when P ≤ 5W, an increase in power has a positive impact on the quality, surface porosity, roughness reduction, line-spacing reduction, and water contact-angle enhancement of the graphene. Conversely, when P > 5 W, higher power negatively affects both the substrate and the graphene structure by inducing excessive ablation. However, it influences the graphene line height positively and is consistent with overall experimental-simulation congruence. Furthermore, the incorporation of high-quality graphene resulted in a surface that exhibited higher contact angles (CA > 120°), lower energy consumption, and higher heating efficiency compared to the use of traditional electrically heated materials for anti-icing applications. The potential applications of this one-step fabrication method extend across various industries, particularly aviation, marine engineering, and other ice-prone domains. Moreover, the method has extensive prospects for addressing pivotal challenges associated with ice formation and serves an innovative and efficient anti-icing technology.

This study explores the near-surface dispersion mechanisms of contaminants in coastal waters, leveraging a comprehensive method that includes using dye and drifters as tracers, coupled with diverse observational platforms like drones, satellites, in-situ sampling, and HF radar. The aim is to deepen our understanding of surface currents' impact on contaminant dispersion, thereby improving predictive models for environmental incident management, including pollutant releases. Rhodamine WT dye, chosen for its significant fluorescent properties and detectability, along with drifter data, allowed us to investigate the dynamics of near-surface physical phenomena such as the Ekman current, Stokes drift, and wind-driven currents. Our research emphasizes the importance of integrating scalar tracers and Lagrangian markers in experimental designs, revealing differential dispersion behaviors due to near-surface vertical shear caused by the Ekman current and Stokes drift. The elongation direction of the dye patch aligns with the Ekman current direction during slow current conditions. Analytical calculations of vertical shear, based on the Ekman current and Stokes drift, closely matched those derived from tracer observations. Over a 7-hour experiment, the vertical diffusivity of near-surface water was observed at 2×10-4 m2/s, and the horizontal eddy diffusivity of the dye patch and drifters reached the order of 1 m2/s and at a 1000m length scale. Particle tracking models demonstrate that while HF radar currents can effectively predict the trajectories of tracers near the surface, incorporating near-surface currents, including Ekman current, Stokes drift, and windage, is essential for a more accurate prediction of the fate of surface floats.

The surface velocity of the Amery Ice Shelf (AIS) is vital to assessing its stability and mass balance. Previous studies have shown that the AIS basin has a stable multi-year average surface velocity. However, spatiotemporal variations in the surface velocity of the AIS and the underlying physical mechanism remain poorly understood. This study combined offset tracking and DInSAR methods to extract the monthly average surface velocity of the AIS and obtained the inter-annual surface velocity from the ITS_LIVE product. An uneven spatial distribution in inter-annual variation of the surface velocity was observed between 2000–2022, although the magnitude of variation was small at less than 20.5 m/yr. The increase and decrease in surface velocity on the eastern and western-central sides of the AIS, respectively, could be attributed to the change in the thickness of the AIS. There was clear seasonal variation in monthly average surface velocity at the eastern side of the AIS between 2017–2021, which could be attributed to variations in the area and thickness of fast-ice and also to variations in ocean temperature. This study suggested that changes in fast-ice and ocean temperature are the main factors driving spatiotemporal variation in the surface velocity of the AIS.

In light of the critical and emerging global challenge posed by the increasing frequency and severity of heatwaves in recent decades, this study demonstrates a practical and robust workflow that bridges the gap in understanding how the effective integration of remote sensing data with ground-based observations can facilitate a comprehensive assessment of spatiotemporal heatwave patterns and trends in the central region of Thailand. This research transcends traditional methods, utilizing air temperature (Tair) and satellite-derived land surface temperature (LST) data from 1981 to 2019. Results exhibit that an analysis of Tair indicates increasing daytime heatwaves in peri-urban areas, with significant trends in heatwave number (HWN), heatwave frequency (HWF), and heatwave duration (HWD), heatwave amplitude (HWA) rises in urban settings while nighttime heatwaves significantly intensify in rural locales. Notably, LST trends reveal varied patterns, with peri-urban areas showing marked daytime increases in heatwave magnitude (HWM), HWA, and HWF. Correlation analysis (p=0.05) highlights strong daytime associations between Tair and LST in rural (HWN, HWF, HWD, r>0.90) and peri-urban (HWM, HWA, r>0.65) regions. Overall, this study advances approaches to the adaptable measurement and spatial-temporal pattern of heatwave-related risk areas, providing insights for decision-makers to develop sustainable practices and strategies for climate change adaptation.

In this study a material based on Polyethylene (PE) and Microcrystalline Cellulose (MC) was developed as a breathable packaging film. Surface functionalization of MC with 3 aminopropyltriethoxysilane (APTES) shows to be an efficient alternative to tailor their properties and increase opportunities for the application of MC on the reinforcement of polymers such polyethylene (PE). Functionalization of MC with mentioned silane derivative was achieved using a green method and later used on the development of composites with PE in three percentages (1, 3 and 5%). All the materials were prepared by melt blending and characterized, in terms of structural properties (ATR-FTIR and FTIR in transmittance, EDX, SEM), thermal properties (DSC and TGA), thermomechanical properties (DMA), contact angle measurements and permeability to oxygen and water vapor. The materials demonstrated to have potential to be used as breathable film packaging of fresh products.

To facilitate the computation of the uniaxial compressive strength value of the cemented paste backfill under the condition of high sand-cement ratio, and to analyze the size effect of the cemented paste backfill with high sand-cement ratio under varied aspect ratios, the cemented paste backfill specimens with sand-cement ratios of 8:1-24:1 and aspect ratios of 0.5, 1, and 2 were prepared. Through response surface experiments and finite element analysis, the influence of three aspect ratios on the cemented paste backfill strength was explored, and the failure characteristics and size effect mechanisms of cemented paste backfill with various aspect ratios were analyzed. The model of strength conversion between cemented paste backfill with different aspect ratios was established. The results show that the compressive strength of the cemented paste backfill decreases with the increase of the aspect ratio under the same mass concentration and sand-cement ratio. When the aspect ratio is 0.5 and 1, the splitting failure is the main factor; when the aspect ratio is 2, the shearing failure is the main factor. The three-dimensional stress caused by the end effect of the cemented paste backfill is the main reason for the high strength when the aspect ratio is 0.5. Due to the one-dimensional stress zone generated in the middle of the cemented paste backfill with an aspect ratio of 2 in the laboratory, its strength value is closer to the actual uniaxial compressive strength value of the cemented paste backfill. The strength values of the cemented paste backfill with aspect ratios of 0.5 and 1 were higher than the actual uniaxial compressive strength values in the laboratory. The rationality of the theoretical analysis was verified by the ABAQUS analysis results. According to the experimental results, a strength conversion model between different aspect ratios is established, which can provide a reference for the design of the uniaxial compressive strength of the cemented paste backfill.

This research investigates precision enhancement in regional quasi-geoid refinement through ADS80 tri-linear array scanning stereoscopic imagery for aerial triangulation, coupled with GNSS gravity-potential modeling. Acquiring stereoscopic imagery and analyzing triangulation accuracy with the ADS80 camera, we performed this study over the Qinghai-Tibet Plateau's elevated, desolate terrain, collecting 593 GNSS points following high-precision stereoscopic imagery model. Utilizing 12 gravity satellite models, we computed geoid heights and China 1985 Yellow Sea elevations for 28 benchmarks and GNSS points, thereby refining the Qinghai Province Quasi-Geoid Model (QPQM) using geometric techniques. The findings reveal that POS-assisted ADS80 stereoscopic imagery yields high-precision triangulation with maximal horizontal and elevation accuracies of 0.083/0.116 cm and 0.053/0.09 cm, respectively, across five control point arrangements. The RMSE of normal heights for 1985, processed via these GNSS points, achieved decimeter precision. By applying error corrections from benchmarks to the 1985 elevation data from gravity satellites and performing weighted averaging, the precision of EGM2008, SGG-UGM-2, and SGG-UGM-1 models improved to 8.61 cm, 9.09 cm, and 9.38 cm, respectively, surpassing the QPQM by 9.22 cm to 9.99 cm. This research demonstrates that the proposed methods can significantly enhance the precision of regional quasi-geoid surfaces. Additionally, these methods offer a novel approach for rapidly establishing regional quasi-geoid models in the uninhabited areas of the Qinghai-Tibet Plateau.

The erosion of surface pipelines induced by proppant flowback during shale gas production is significant. The surface pipelines in a shale gas field in the Sichuan Basin experienced perforation failures after only five months of service. To investigate the erosion features of L360N, coatings, and ceramics and optimize the selection of two protective materials, a gas-solid two-phase flow jet erosion experimental device was used to explore the erosion resistance of L360N, coating, and ceramic under different impact velocities (15 m/s, 20 m/s, and 30 m/s). An energy dispersive spectroscope, a scanning electron microscope, and a laser confocal microscope were employed to analyze erosion morphologies. With the increase in flow velocity, erosion depth and erosion rate of L360N, coating, and ceramic increased and peaked under an impact velocity of 30 m/s. Maximum erosion rate and maximum erosion depth of L360N were respectively 0.0350 mg/g and 37.5365 µm. Its primary material removal mechanism was plowing of solid particles and microcracks were distributed on the material surface under high flow velocities. Maximum erosion rate and maximum erosion depth of coating were respectively 0.0217 mg/g and 18.9964 µm. Its primary material removal mechanism was the detachment of the binder phase Co caused by plowing. Maximum erosion rate and maximum erosion depth of ceramics were respectively 0.0108 mg/g and 12.4856 µm. The erosion mechanisms were micro-cutting and plowing. Under different particle impact velocity, different erosion morphologies were observed, but the primary erosion mechanism was the same. The erosion resistance of ceramics was higher than that of coating. Therefore, ceramic lining materials could be used to protect the easily eroded parts, such as pipeline bends and tees, and reduce the failure rate by more than 93%. The study provided the data and theoretical basis for the theoretical study on oil and gas pipeline erosion and pipeline material selection.

Heterogeneous distribution of delivery or treatment modalities within the tumor mass is a crucial limiting factor for a vast range of theranostic applications. Understanding the interactions between a nanomaterial and the tumor microenvironment will help to overcome challenges associated with tumor heterogeneity as well as the clinical translation of nanotheranostic materials. This study aims to evaluate the influence of protein surface adsorption on gold nanoparticle (GNP) biodistribution using high resolution Computed Tomography (CT) preclinical imaging in C57BL/6 mice harboring Lewis Lung Carcinoma (LLC) tumors. LLC provides a valuable model for study due to its highly heterogenous nature which makes drug delivery to the tumor challenging. By controlling the adsorption of proteins on the GNP surface, we hypothesize that we can influence the intratumoral distribution pattern and particle retention. We performed an in vitro study to evaluate the uptake of GNPs by LLC cells and an in vivo study to assess and quantify the GNP biodistribution by injecting concentrated GNPs citrate stabilized or passivated with Bovine Serum Albumin (BSA) intratumorally into LLC solid tumors. Quantitative CT and Inductively Coupled Plasma Optical Emission Spectrometry (ICP-OES) results both confirm the presence of particles in the tumor 9 days post-injection (n=8 mice/group). Significant difference is highlighted between citrate-GNP and BSA-GNP groups (**p < 0.005, Tukey’s multiple comparisons test), confirming the protein corona of GNPs modifies intratumoral distribution and retention of the particles. In conclusion, our investigations show that the surface passivation of GNPs influences the mechanism of cellular uptake and intratumoral distribution in vivo highlighting the spatial heterogeneity of the solid tumor.

Based on the panel data from 31 provinces in China from 2012 to 2020, this paper uses the TOPSIS method to measure the development level of the digital economy and environmental quality. Then, a coupled coordination degree model is used to analyse the relationship between the digital economy and environmental quality. Kernel density estimation and the Dagum Gini coefficient method were used to reveal the dynamic evolution trend of the coupled coordination level between the digital economy and environmental quality and the regional trends of coupled indicators. Finally, the dynamics of the above relations were explored with an econometric model. The results show that the coupled coordination degree of the digital economy and environmental quality displays obvious regional heterogeneity, and the national coordination level exhibits dynamic convergence characteristics. The heterogeneity of the coupled coordination degree of the two systems in the eastern region has decreased year by year, except in the western region, the central region and the northeast region, where an upwards trend is observed. Overall, the Gini coefficient of the coupled coordination degree between the digital economy and environmental quality displays a certain downwards trend. The level of economic development, technological innovation level, industrial structure, degree of opening to the outside world, degree of environmental regulation, marketization index and financial development level have a positive influence on the coupled coordination of the digital economy and environmental quality. Environmental regulation is the core driver of the coupling of the two systems, and the economic development level, technological innovation level, industrial structure and degree of openness are the other major drivers. Therefore, in the processes of digital economy transformation and environmental governance, all regions should focus on balanced development between regions to optimize the overall efficiency of the two systems, consider external influence, enhance internal capabilities, and promote the coordination and co-development of the two systems.

In this research paper, a novel high step up dc-dc converter with a coupled inductor and voltage doubler circuits is proposed. The converter achieves a high step up voltage gain with an appropriate duty ratio and low voltage stress on the power switches. Also, the energy which is stored in the leakage inductor of the coupled inductor can be recycled to the output. The operating principles and the steady state analysis of the proposed converter are discussed in detail. Finally, a prototype circuit of the proposed converter is implemented in the laboratory in order to verify the performance of the proposed converter.

In this article, a novel hybrid welding process called plasma-TIG coupled arc welding was proposed to improve the efficiency and quality of welding by utilizing the full advantage of plasma and TIG welding processes. The two arcs of plasma and TIG were pulled into each other into one coupled arc under the effect of Lorentz force and plasma flow force during welding experiments. The arc behavior of coupled arc was studied by means of it’s arc profile, arc pressure and arc force conditions. The coupled arc pressure distribution measurements were performed. The effects of welding conditions on coupled arc pressure were evaluated and the maximum coupled arc pressure was improved compared with single-plasma arc and single-TIG arc. It was found that the maximum arc pressure was mainly determined by plasma arc current and plasma gas flow. According to the results, the proposed coupled arc welding process have both advantages of plasma arc and TIG method, and it has a broad application prospect.

The results of numerical experiments with the chemistry-climate model of the Institute of Numerical Mathematics of the Russian Academy of Sciences - Russian State Hydro-Meteorological University (INM-RSHU CCM) in comparison with the MERRA2 reanalysis data are presented. To assess the impact of sea surface temperature (SST) on stratospheric processes and the ozone layer, numerical experiments were carried out for scenarios corresponding to the El Niño and La Niña Southern Oscillation phases. It is shown that the El Niño phase contributes to the enhancement of heat and mass transfer to the polar stratosphere, which strengthen the Brewer-Dobson circulation and the flux of wave activity that affect the zonal wind. As a result, during El Niño, the probability of sudden stratospheric warming increases and the stratospheric polar vortex (SPV) weakens, re-sulting in an increase in total polar stratospheric ozone. The La Niña phase, on the contrary, is accompanied by a weakening of heat and mass transfer from the troposphere to the stratosphere, as a result of which the stratospheric polar vortex strengthens and the total column ozone decreases. It is shown that the effect associated with the Southern Oscillation is more pronounced in the Northern Hemisphere than in the Southern Hemisphere. Numerical experiments were also carried out for scenarios in which the sea surface temperature was set corresponding to the early 1980s, and the results were compared with calculations in which the SST was set corresponding to the late 2010s. This allowed us to assess the influence of the multiyear trend in the SST increase on stra-tospheric processes and the ozone layer. It was shown that the SST increase is most pronounced in the Arctic, which corresponds to the phenomenon of "Arctic amplification", and therefore, the heat and mass transfer to the stratosphere increases in the Northern Hemisphere, which contributes to some weakening of the SPV and increase of the total column ozone. But, compared to the Southern Oscillation, the influence of the SST trend on the SPV and total column ozone is much weaker and is observed mainly in the Northern Hemisphere.

Brushless Direct Current Motors are significantly improved for using many electrical applications. The design investigation is increased year by year and most of the motor design researchers find out the superior efficiency of the BLDC motor. The traditional motor consumed more electrical power than BLDC motor. The design of BLDC motors that are compact, small, easy to control, save energy and light weight. Due to this fact, the design of BLDC motor should be analyzed to improve the motor characteristics performance. The research focuses on the design of BLDC motor performance using Taguchi Method and Response Surface Methodology (RSM) for Finite Element Method (FEM). Firstly, the Taguchi Method is applied to identify the optimization point of design parameters and consider using the reference model of actual BLDC electric fan motor with a rated power of 26Watts design. Based on the Taguchi Method to create the RSM is used to two-step optimization design performance using in FEM analysis. The performances of motor design proposed approach to provide the effeteness for motor design investigator. In this investigation aims the better structural performances in output power, torque, efficiency and torque ripple. The final design of proposed model achieved an energy efficiency is 10% higher than the reference design of prototype modes, the output power result is 10W higher this reference design. We can reduce the loss of the proposed motor design. Furthermore, the maximum torque can also increase the 0.032Nm of that design. The design simulation results were produced and studied by the FEM analysis of JMAG software. From the evaluation results, the configurations of reference model design are compared with the proposed design by using the three methods of motor design optimization showed the best characteristics for performance of motor investigation design.

The present study propose an innovative turn-boring operation method and focuses on finding optimal turn-boring process parameters for AA7050-T7451 by considering multiple performance characteristics using Taguchi orthogonal array with the grey relational analysis, the effect of cutting variables such as, feed rate, depth of cut and cutting speed are optimized with considerations of multiple performance characteristics namely surface roughness, roundness error, material removal rate and power consumption the optimal values were found out from the Grey relational grade. The result of the Analysis of Variances (ANOVA) is proved that the most significant factor is cutting speed, followed by feed rate, radial depth of cut. Finally, confirmation tests were performed to make a comparison between the experimental results. Experimental results have shown that machining performance in precision turn-boring process can be improved effectively through this approach

Following legalization, cannabis has quickly become an important horticultural crop in Canada and increasingly so in other parts of the world. However, due to previous legal restrictions on cannabis research there are limited scientific data on the relationship between nitrogen (N), phosphorus (P), and potassium (K) supply (collectively: NPK) and the crop yield and quality. This study examined the response of a high delta-9-tetrahydrocannabinol (THC) Cannabis sativa cultivar grown in deep-water culture with different nutrient solution treatments varying in their concentrations (mg L^-1) of N (70, 120, 180, 250, 290), P (20, 40, 60, 80, 100) and K (60, 120, 200, 280, 340) according to a central composite design. Results demonstrated that inflorescence yield responded quadratically to N and P, with the optimal concentrations predicted to be 194 and 59 mg L^-1, respectively. Inflorescence yield did not respond to K in the tested range. These results can provide guidance to cultivators when formulating nutrient solutions for soilless cannabis production and demonstrates the utility of surface response design for efficient multi-nutrient optimization.

In this article, we describe a simple procedure for evaluating the sterility of nutrient media using a shear-horizontal surface acoustic wave (SH-SAW) biosensor. We used the SH-SAW biosensor platform to monitor the time-dependent phase responses of the material for the media that binds to a monolayer of 3-mercaptopropanyl-N-hydroxy succinimide on the biosensor surface. Increases in the phase shift less than 50% of the starting phase shift recorded 180 minutes after the sterilization indicate a successful sterility test of the media. Our devices were then applied to sterility testing using a viable Escherichia coli (E. coli) K-12 solution to confirm our hypothesis. Filtered LB Broth was the negative control, and a 24-hour culture of E. coli was the positive control. Before testing, the cell solution was pelleted, the media decanted, and then replaced with a 1x phosphate-buffered saline solution (1x PBS). Since we know that the N-hydroxysuccinimide residues will bind to amine groups, only in cases where microbial species are present will the surface binding increase greater than 50%. We confirmed our hypothesis using SH-SAW biosensors and overnight E. coli cultures. The sensitivity for our 250 MHz quartz SH-SAW sensors was calculated based on the response from the E. coli K-12 solution over the linear dynamic range, which appears to be 2x10^4 – 2x10^7 CFU per ml and has a sensitivity of S = 1.655x10^5 o m2 Kg-1. The limit of detection (LOD) for these sensors was calculated to be approximately 2x10^-9 grams (g), which is estimated to be approximately 2,000 Escherichia coli (E. coli) K-12 cells. However, the sensitivity and insertion loss remained approximately unchanged before and after coating the sensor with 3,3'-Dithiobis(succinimidyl) Propionate (DSP).

The main purpose of this work was to tests of form and size of fatigue wear of the top layer of oil gear pump wheel (3PW-BPF-24). The object of tests was operated during a determined number of hours at strictly controlled operational and environmental parameters. A microscope of focal differentiation by Alicona InfiniteFocus G4 (with Focus-Variation optical measuring technology) was used for an identification, measurement and description of noticed superficial defects, which resulted from the fatigue process of the top layer and an earlier thermochemical treatment. The work was finished with an analysis of obtained results (based on the analysis of 3D scans) and conclusions concerning about optimization of the thermal treatment. Taking into consideration the presented results (suggestions) in the technology of improving strength properties of gear wheels (of this type oil pumps) may render it possible to obtain an appropriate fatigue endurance of the top layer, i.e. a minimization of observed superficial defects.

We discuss in detail a well known method for obtaining the frequencies of the normal modes of coupled harmonic oscillators that is based on the simultaneous diagonalization of two symmetric matrices. We apply it to some simple illustrative examples recently chosen for the presentation of an alternative approach based on a set of constants of the motion. We show that the traditional method is simpler, even in the case of equal frequencies. We also discuss a problem that commonly appears in elementary courses on quantum mechanics that also requires the diagonalization of two symmetric matrices.

The variation of aerosols, especially dust aerosol, in time and space plays an important role in climate forcing studies. Aerosols can effectively reduce land surface longwave emission and re-emit energy at a colder temperature, making estimation of downwelling surface longwave radiation (DSLR) with satellite data difficult. Using the latest atmospheric radiative transfer code (MODTRAN 5.0), we simulate the outgoing longwave radiation (OLR) and DSLR under different land surface and atmospheric profile conditions. The results show that dust aerosol has an obvious “warming” effect to longwave radiation compared with other aerosols, that aerosol longwave radiative forcing (ALRF) increased with increasing aerosol optical depth (AOD), and that the atmospheric water vapor content (WVC) is critical to the understanding of ALRF. A method is proposed to improve the accuracy of DSLR estimation from satellite data for the skies under heavy dust aerosols. The AOD and atmospheric WVC under cloud-free conditions with a relatively simple satellite-based radiation model that yields the high accurate DSLR under heavy dust aerosol are used explicitly as model input to reduce the effects of dust aerosol on the estimation of DSLR. Validations of the proposed model with satellites data and field measurements show that it estimates the DSLR accurately under heavy dust aerosol skies. The root mean square errors (RMSEs) are 20.4 W/M² and 24.2 W/M² for Terra and Aqua satellites, respectively, at the Yingke site, and the biases are 2.7 W/M² and 9.6 W/M², respectively. For the Arvaikheer site, the RMSEs are 23.2 W/M² and 19.8 W/M² for Terra and Aqua, respectively, and the biases are 7.8 W/M² and 10.5 W/M², respectively. The proposed method is especially applicable to acquire relatively high accurate DSLR under heavy dust aerosol using MODIS data with available WVC and AOD data.

In this study, the efficiency of an anaerobic treatment system for wastewater from a South African poultry slaughterhouse was evaluated using a lab-scale static granular bed reactor (SGBR). The down-flow SGBR (2 L) was operated continuously for 138 days under mesophilic conditions (35-37 ˚C), at hydraulic retention times (HRTs) ranging from 24 to 96 h and average organic loading rates (OLRs) of 0.78 to 5.74 g COD/L.day. The SGBR achieved an average chemical oxygen demand (COD) removal efficiency of 80% and the maximum COD removal achieved was 95%, at an HRT of 24 h and average OLR of 5.74 g COD/L.day. The optimization of the SGBR, with regard to a suitable HRT and OLR, was determined using response surface methodology (RSM). The optimal SGBR performance with regard to the maximum COD removal efficiency was predicted for an OLR of 12.49 g COD/L.day and a HRT of 24 h, resulting in a 95.5% COD removal efficiency. The model R2 of 0.9638 indicated that the model is a good fit and is suitable to predict the COD removal efficiency for the SGBR.

Emergence of multi drug resistant (MDR) and extensively drug resistant (XDR) Mycobacterium tuberculosis poses a serious threat to TB control as the available treatment options are less effective in these cases. Therefore, new strategies are required for identification of new drugs and drug targets. The M. tuberculosis dihydrodipicolinate synthase is a putative drug target with no potent inhibitor. Here in this study, we have used a comprehensive computational approach to identify small molecule inhibitors and validated them in vitro. As similar structures tend to have similar functions, therefore 3 approaches, namely, (a) known inhibitor-based approach, (b) substrate analogues, (c) product analogues were used for compound screening from various chemical libraries. The fourth approach we have taken is fragment library screening.In vitro studies revealed that β-hydroxypyruvic acid tartronic acid are inhibitors of Mtb-rDapA with maximum inhibition 48% and 51% at 500µM concentrations respectively. We have also observed that β-hydroxypyruvic acid is a time dependent inhibitor of Mtb-rDapA. Further, thermal shift assays showed that β-hydroxypyruvic acid interacts with Mtb-rDapA and the thermal stability of Mtb-rDapA shifted by 3˚C. Among the product analogues of Mtb-DapA, dipicolinic acid showed to bind to Mtb-rDapB shifting thermal stability of Mtb-rDapB by 0.5˚C in binding. Additionally, we have designed a new approach by combining substrate and product analogues to achieve better inhibitions. In vitro assays validated that this combination approach increased maximum inhibition up to 100%. We envision that these compounds would serve as potent leads for tuberculosis drug discovery.

This research was devoted to study the effect of the tacticity of PMMA on the surface physicochemical properties such as the London dispersive component of the surface energy of the polymer, the polar and dispersive free energies, the Lewis’s acid-base surface parameters, and the Lewis acid and base surface energies of atactic, isotactic and syndiotactic PMMAs as a function of the temperature. Inverse gas chromatography (IGC) at infinite dilution was used to determine the surface thermodynamic properties of PMMA at different tacticities. The experimental values of the net retention time and volume of model organic molecules adsorbed on the atactic, isotactic and syndiotactic PMMAs, were obtained by IGC technique at infinite dilution. The London dispersion interaction energy was used for the separation of the polar and dispersive energy of the different n-alkanes and polar solvents adsorbed on the different PMMA surfaces. The London dispersive surface energy γ_s^d (T) of PMMAs was determined by applying the Hamieh thermal model that took into account the effect of the temperature on the surface area of adsorbed molecules. The obtained results showed non-linear variations of γ_s^d (T) of atactic, isotactic, and syndiotactic PMMAs with three maxima characterizing the three transition temperatures of PMMAs, T_g, T_g and T_(liq-liq) with a shift of these temperatures with the isotactic and syndiotactic PMMAs. It was showed that the polar interaction free energy ∆G_a^p (T) also showed the presence of the three above transition temperatures of the polymers. The study showed an important non-linearity variation of the different acid-base parameters in the various polymer surfaces proving the highest effect of the temperature and the tacticity on these parameters. The determination of the enthalpic and entropic Lewis’s acid-base parameters showed an amphoteric character for the different PMMAs. The basicity of the atactic PMMA was about four times larger than its acidity outside the neighborhood of the transition temperatures of the polymer. Whereas, the isotactic PMMA was about 2 to 2.5 times more basic than acid, while the syndiotactic PMMA exhibited the highest basicity by showing a surface 5 to 8 times more basic than acid. However, the Lewis acid-base parameters strongly depended on the temperature and sudden variations of these surface parameters were observed around the transition temperatures largely depending on the PMMA tacticity. The determination of the polar acid and base surface energies of the three PMMAs led to the same previous transition temperatures with an important effect of the tacticity of PMMA on the values of these acid-base surface energies.

This paper presents the results of investigations into the pyrolysis of waste polypropylene in a laboratory fixed-bed batch reactor. The experiments were designed and verified in such a way as to allow the application of the Response Surface Methodology (RSM) in the development of an empirical mathematical model that quantifies the impacts mentioned above. The influence of the mass of the raw material (50, 100 and 150 g), together with the reactor temperature (450, 475 and 500 °C) and the reaction time (45, 50 and 75 min) was examined. It has been shown that the mass of the raw material, i.e. the filling volume of the reactor, has a significant influence on the pyrolysis oil yield. This influence exceeds the influence of reactor temperature and reaction time. This was explained by observing the temperature change inside the reactor at three different spots at the bottom, middle and top of the reactor. Recorded temperature diagrams show that with greater masses of feedstock, local overheating occurs in the middle part of the reactor, which leads to overcracking of vapor products, and from there to an increased formation of non-condensable gases, i.e. reduced yield of pyrolytic oil.