The working environment of mining electric locomotives is wet and muddy coal mine 1 roadway. There may be idling or slipping between the wheels and rails of mining electric locomotives 2 due to low friction between the wheel and rail and insufficient utilization of creep rate. Therefore, it 3 is necessary to control the creep rate within a reasonable range. In this paper, the autonomous control 4 algorithm for mining electric locomotives based on improved ε-greedy is theoretically proven to be 5 convergent and effective firstly. Secondly, after analyzing the contact state between the wheel and rail 6 under wet and slippery road conditions, it was concluded that the value of creep rate is an important 7 factor affecting the autonomous driving of mining electric locomotives. Therefore, the autonomous 8 control method for mining electric locomotives based on creep control is proposed in this paper. 9 Finally, the effectiveness of the proposed method was verified through simulation. The problem of 10 wheel slipping and idling caused by insufficient friction of mining electric locomotives in coal mining 11 environments is effectively suppressed. Autonomous operation of vehicles with optimal driving 12 efficiency can be achieved through quantitative control and utilization of the creep rate between 13 wheels and rails

Tinnitus is a common phantom auditory percept, believed to be related to plastic changes in the brain due to hearing loss. However, tinnitus can also occur in absence of any clinical hearing loss. Then, since there is no hearing loss, the mechanisms that drive plastic changes remain largely enigmatic. Previous studies showed subtle differences in sound-evoked brain activity associated with tinnitus in subjects with tinnitus and otherwise, normal hearing, but the results are not consistent across studies. Here, we aim to investigate those differences using monaural rather than binaural stimuli. Sound-evoked responses were measured using functional magnetic resonance imaging (MRI) in participants with and without tinnitus. All participants had clinically normal audiograms. The stimuli were pure tones with frequencies between 353 and 8000 Hz, presented monaurally. A Principal Component Analysis (PCA) of the response in the auditory cortex revealed no difference in tonotopic organization, which confirmed earlier studies. A GLM analysis showed hyperactivity in the lateral areas of the bilateral auditory cortex. Consistent with the tonotopic map, this hyperactivity mainly occurred in response to low stimulus frequencies. This may be related to hyperacusis, which was associated with tinnitus found in the parahippocampus. This may reflect an interference between tinnitus and spatial orientation.

Sialylated milk oligosaccharides (SMOs) is the most important oligosaccharides in human milk oligosaccharides (HMOs), and have a multifunctional health benefit, and the most abundant SMOs are sialyllactose (SLs). The previous studies indicate that the growth of tumor cells, and angiogenesis on tumor tissues with Lewis lung carcinoma, melanoma, and colon carcinoma cells could be prevented by SL. Thus, it has been proposed that SL might be an ideal candidate for the development of anti-angiogenic drugs without any side effects. It has been proposed that the Sialic acid (Sia) can be produced through SL’s hydrolysis, and the dietary Sia is further transported to the brain and other tissues though blood for formation of CMP-Sia, the activated precursor of Sia, and then is catalyzed by polysialyltransferases (polySTs) for synthesis of polysialic acid (polySia) or polysialylation of neural cell adhesion molecule (NCAM). Thus, it’s necessary to study and develop new inhibitors, which not only modulate a proper balance between the gut health and neuros system development, but also inhibit the overexpression of polySia, and thus block the tumor cell migration. In this study, we proposed that 3’-SL and 6’-SL may be more ideal inhibitors comparing with two previous inhibitors, the low molecular weight heparin (LMWH) and cytidine monophosphate (CMP) in the previous studies.

Chlamydia trachomatis (Ct) infections are the most common sexually-transmitted infection (STI). Despite effective antibiotics for Ct, undetected infections or delayed treatment can lead to infertility, ectopic pregnancies, and chronic pelvic pain. Besides humans, chlamydia poses similar health challenges in animals such as C. suis (Cs) in pigs. Based on the similarities between humans and pigs as well as their chlamydia species, we use pigs as a large biomedical animal model for chlamydia research. In this study, we use the pig model to develop a vaccine candidate against Ct. The vaccine candidate consists of TriAdj-adjuvanted chlamydial protease-like activity factor (CPAF) protein. We tested two weekly administration options – twice intranasal (IN) followed by twice intramuscular (IM), or twice IM followed by twice IN. We assessed the humoral immune response not only in serum by CPAF-specific IgG including antibody avidity determination but also in cervical and rectal swabs by CPAF-specific IgG and IgA ELISAs. The systemic T-cell response was analyzed upon in vitro CPAF-restimulation via IFN-γ and IL-17 ELISpots as well as intracellular cytokine staining flow cytometry. Our data demonstrate that while the IN/IM vaccination mainly led to non-significant systemic immune responses, the vaccine candidate is highly immunogenic if administered IM/IN. This vaccination strategy induced high serum anti-CPAF IgG levels with strong avidity as well as high IgA and IgG levels in vaginal and rectal swabs and in uterine horn flushes. In addition, this vaccination strategy prompted a pronounced cellular immune response: Besides inducing IL-17 production, the vaccine candidate induced a strong IFN-γ response by CD4 T cells. In the IM/IN vaccinated pigs, these cells also significantly downregulated their CCR7 expression – a sign for differentiation into peripheral tissue homing effector/ memory cells. Conclusively, this study demonstrates strong immunogenicity of the IM/IN administered TriAdj-adjuvanted Ct CPAF vaccine candidate. Future studies will test vaccine efficacy of this promising Ct vaccine candidate. In addition, this project demonstrates suitability of the Cs pre-exposed outbred pig model for Ct vaccine development. Thereby, we aim to open the bottleneck of large animal models to facilitate the progression of Ct vaccine candidates into clinical trials.

Recent pollinator declines have focused efforts on their conservation which require clear estimates of pollination value to agriculture. Our socio-economic producer surveys and agronomic field research data were used to present a new way of estimating ecosystem service value of native pollinators. Using two regionally important U.S.A. crops, Maine wild blueberry and Massachusetts cranberry as models, we present perceived values of native bee pollinators from both consumer and producers. Wild blueberry’s Replacement Cost (RC) was greater than Attributable Net Income (ANI), since greater rented honey bee stocking densities are required. Attributable Net Income for native bees were similar for wild blueberry ($613/ha) and cranberry ($689/ha). Marginal Net Farm Income (MNFI) from incrementally adding more hives per ha was greater from stocking a third/fourth hive per ha for cranberry ($6,206) than stocking a ninth/tenth hive per ha for wild blueberry ($556), given greater responsiveness of yield, revenue, and profit to using rented honey bee hives in cranberry compared to wild blueberry. Both crops’ producers were only willing to annually invest $140–188/ha in native pollination enhancements on their farms, justifying government support. Consumers are willing to pay ~6.7 times more to support native bees than producers, supporting market-based support for invertebrate conservation.

Quorum sensing (QS) is a sophisticated bacterial cell-to-cell communication mechanism that allows bacteria to sense population density through the secretion and detection of diffusible small molecular signals. This process leads to the coordinated expression of specific genes at the transcriptional level. Over time, continuous research has elucidated the genetic elements and regulatory principles of QS. Recently, synthetic biology has leveraged these insights to construct genetic circuits incorporating QS components, enabling both intra-species and inter-species artificial communication. These QS-based genetic circuits hold significant potential for applications in biotechnology and biomedicine. This paper reviews several well-characterized microbial QS systems and their functional roles, while also introducing the application of QS-based genetic circuits in cellular communication across species. The paper further discusses the role of QS in the development of biological computing tools, population density regulation, and metabolic flux control, offering a forward-looking perspective on future advancements. For intra-species communication, the focus is on the use of QS systems in constructing biological computing tools, including toggle switches, biosensors, and logic gates in synthetic biology. These tools, designed on the QS mechanism, can more precisely coordinate cellular behavior by integrating biological control circuits to achieve spatial, temporal, and population-level regulation. In the context of inter-species communication, the introduction of QS systems plays a pivotal role in population density control and metabolic flow regulation. By recombining metabolic networks, QS enables the redistribution of metabolic flux in desired pathways, facilitating the regulation of population density and the co-culture of mixed strains. Moreover, combining QS with oscillator models has shown great potential in synchronizing microbial communities. In summary, in-depth research into QS mechanisms and their applications not only lays a solid foundation for understanding microbial ecological competition and dynamic balance, but also offers promising avenues for regulating pathogenic bacteria and developing innovative disease control strategies.

Assessing the quality of corn seeds necessitates evaluating their content of water, fat, protein, and starch. This study integrates hyperspectral imaging technology with chemometric analysis techniques to achieve non-invasive and rapid detection of multiple key components in corn seeds. Hyperspectral images of the embryo surface of maize seeds were collected within the wavelength range of 1100~2498nm. Subsequently, image segmentation techniques were applied to extract the germ structure of the corn seeds as the region of interest. Seven spectral data preprocessing algorithms were employed, and the Detrending Transformation (DT) algorithm was identified as the optimal preprocessing method through comparative analysis using the Partial Least Squares Regression (PLSR) model. To reduce spectral redundancy and streamline the prediction model, three algorithms were employed for characteristic wavelength extraction: Successive Projections Algorithm (SPA), Competitive Adaptive Reweighted Sampling (CARS), and Uninformative Variable Elimination (UVE). Using both the original spectra and the extracted characteristic wavelengths, four content detection models were constructed: PLSR, Back Propagation Neural Network (BPNN), Radial Basis Function Neural Network (RBFNN), and Least Squares Support Vector Machine (LSSVM). The experimental results demonstrate that the DT-CARS-LSSVM model exhibits exceptional accuracy and stability in predicting these four key components, with determination coefficients of 0.9877, 0.9344, 0.9827, and 0.9592, respectively. This study not only provides a scientific basis for evaluating the quality of corn seeds but also opens up new avenues for the development of non-invasive detection technology in related fields.

This paper presents a biologically inspired flocking-based aggregation behaviour of a swarm of mobile robots. Aggregation behaviour is essential to many swarm systems, such as swarm robotics systems, in order to accomplish complex tasks that are impossible for a single agent. We developed a robot controller using Reynolds’ flocking rules to coordinate the movements of multiple e-puck robots during the aggregation process. To improve aggregation behaviour among these robots and address the scalability issues in current flocking-based aggregation approaches, we used a K-means algorithm to identify clusters of agents. Using the developed controller, we simulated the aggregation behaviour among the swarm of robots. Five experiments were conducted using Webots simulation software. The performance of the developed system was evaluated under a variety of environments and conditions, such as various obstacles, agent failure, different numbers of robots and arena sizes. The results of the experiments demonstrated that the proposed algorithm is robust and scalable. Moreover, we compared our proposed algorithm with another implementation of the flocking-based self-organizing aggregation behaviour based on Reynolds’ rules in a swarm of e-puck robots. Our algorithms outperformed this method in terms of cohesion performance and aggregation completion time.

Background: Oral hypoglycemic agents are typically the first-line treatment for type 2 diabetes mellitus (T2DM). This study examines the benefits of initiating insulin as the first-line therapy for newly diagnosed T2DM patients. Methods: A PubMed search using keywords ‘Type 2 Diabetes Mellitus’ and ‘Early STIIT’ included RCTs assessing beta cell function, insulin resistance, glycemic control, and lipid profiles. Revman 5.4.1 software was used for meta-analysis, with outcomes represented as mean difference (MD) and 95% confidence intervals (CI). Results: Significant reductions in fasting blood glucose (FBG: MD -4.75, 95% CI -7.07, -2.43), HbA1c (MD -1.84, 95% CI -3.01, -0.68), and postprandial glucose (PPG: MD -9.02, 95% CI -10.48, -7.56) were observed with early STIIT therapy compared to baseline. Beta cell function improved (HOMA-B: MD 53.70, 95% CI 27.78, 79.63) and insulin resistance decreased (HOMA-IR: MD -1.84, 95% CI -3.65, -0.04). Lipid profile improvements included reductions in total cholesterol (TC), triglycerides (TG), and LDL, with no change in HDL. BMI remained stable (MD -0.15, 95% CI -0.82, 0.51). Most patients achieved long-term remission and glycemic control without oral hypoglycemic agents. Conclusion: Early STIIT in newly diagnosed T2DM patients significantly reduces glycemic markers and maintains long-term glycemic control, preserving beta cell function. The therapy also improves lipid profiles, reducing TC, TG, and LDL. Initiating insulin as a first-line treatment shows promising results for glycemic control and overall metabolic health.

A formulation of nonequilibrium thermo field dynamics has been performed using the nonequilibrium statistical operator method by D.N. Zubarev. Generalized transfer equations for a consistent description of kinetics and hydrodynamics of the dense quantum-field system with strongly coupled states are derived.

Estimating parameters for multiple datasets can be time consuming, especially when the number of datasets is large. One solution is to sample from multiple datasets simultaneously using Bayesian methods such as adaptive multiple importance sampling (AMIS). Here we use the AMIS approach to fit a von Misses distribution to multiple datasets for wind trajectories derived from a Lagrangian Particle Dispersion Model driven from a 3D meteorological data. The primary objective is to characterise the uncertainties in wind trajectories in a form that can be used as inputs for predictive models of wind-dispersed insect pests and pathogens of agricultural crops for use in evaluating risk and in planning mitigation actions. Our results show that AMIS can significantly improve the efficiency of parameter inference for multiple datasets.

Background: The new therapeutic modality incorporating countermeasure against the most plausible environmental factor in inflammatory bowel disease, i.e., a plant-based diet, showed far better outcomes than current standards in inflammatory bowel disease. Infliximab is widely used for induction and subsequent scheduled maintenance therapy in patients with inflammatory bowel disease. However, the efficacy of infliximab diminishes over time. Objectives: To investigate the durability of scheduled infliximab maintenance therapy incorporating plant-based diet in inflammatory bowel disease. Methods: This was a prospective single-group trial at tertiary hospitals. Infliximab maintenance therapy was indicated in patients with severe or unresponsive to conventional therapy. Infliximab (5 mg/kg body weight) was infused every 8 weeks on an inpatient basis, and plant-based diet, a lacto-ovo-vegetarian diet, was served three or four times during hospitalization. Durability was assessed using the Kaplan-Meier method. Results: Twenty-four patients (16 with Crohn’s disease, eight with ulcerative colitis) were included: median age 27.5 years old, disease duration 53.5 months, and concomitant use of immunosuppressant 21%. Intensification of infliximab was employed in 46% of patients. There was no significant difference in durability rates between Crohn’s disease and ulcerative colitis. Durability rates were 87% at both 5 and 10 years. Plant-based diet score in the median follow-up period of 9.3 years, which indicates adherence to the plant-based diet, was significantly higher than the baseline score. Conclusions: Infliximab maintenance therapy incorporating plant-based diet yielded a high durability rate of 87% at 5 years in patients with Inflammatory bowel disease.

Urban rail transit offers advantages like high safety, energy efficiency, and environmental friendliness. With cities rapidly expanding, travelers are increasingly using rail systems, heightening demands for passenger capacity and efficiency while also pressuring these networks. Passenger flow forecasting is an essential part of transportation systems. Short-term passenger flow forecasting for rail transit can estimate future station volumes, providing valuable data to guide operations management and mitigate congestion. This paper investigates short-term forecasting for Suzhou's Shantang Street station. Shantang Street's high commercial presence and distinct weekday versus weekend ridership patterns make it an interesting test case. Wavelet denoising and LSTM modeling were combined to predict short-term flows, comparing the results to standalone LSTM and SVR approaches. This study illustrates that the adopted algorithms exhibit good performance for passenger prediction. The LSTM model with wavelet denoising proved most accurate, demonstrating applicability for short-term rail transit forecasting and practical significance.

The dermatological manifestations of Long Covid (LC) have languished in the shadows of chronic fatigue and brain fog. Yet they are all linked by gut dysbiosis and the cytokine triad of TNF-α, IL-1β, and IL-6. The gut microbiome common not only to LC, psoriasis, AA, and vitiligo but also to neurodegenerative disease has been recently described. This gut microbiome induces an altered tryptophan metabolism linked to autoimmune disease. SARS CoV2 invades enterochromaffin cells rich in ACE2 receptors and curtails absorption of the essential amino acid tryptophan and subsequent synthesis of serotonin and melatonin. This review suggests that an etiologic prebiotic (d-mannose)/probiotic (lactobacilli, bifidobacteria)/postbiotic (butyrate) approach to autoimmune skin disease that improves intestinal barrier integrity and that suppresses the triad of TNF-α, IL-6, and IL-1β may enhance or even eliminate the traditional immunotherapy of targeted monoclonal antibodies, Janus kinase inhibitors, and steroids. Health benefits of this approach extend well beyond suppression of autoimmune skin disease.

We report on the role of synergistic polarization of Ba0.9Sr0.1TiO3 (BST) nanoparticles in sulfur cathodes to enhance the redox kinetics of polysulfides for high-capacity Li-S batteries. Ferroelectric nanoparticles are known to significantly improve the electrochemical performance of Li-S batteries due to their inherent self-polarization and high adsorption capacity towards polysulfides. X-ray diffraction spectra confirmed the tetragonal symmetry (c/a=1.0073), while Raman spectroscopic analysis validated the presence of tetragonal orientation Raman modes in BST-modified composites. Scanning electron microscope (SEM) images showed a homogeneous distribution of BST in the sulfur cathode system, with grain sizes ranging from 1 to 1.5 μm. Notably, the BST-coupled S50BST30CB10PVDF10 composite cathode achieved a capacity of approximately 820 mAh/g at 100 mA/g, maintaining stability over 100 cycles, demonstrating improved electrochemical performance. Two distinct plateaus between 2.3 V to 2.0 V and 2.0 V to 1.5 V further underscore the superior performance of BST ferroelectric nanoparticles in enhancing the redox kinetics of Li-S batteries. By leveraging the favourable affinity of polar substances towards polysulfides, we aimed to create a more stable reactive environment within the cathodic site, effectively trapping polysulfide intermediates through the synergistic polarization of BST nanoparticles. The synergistic polarization induced by the asymmetric crystal structure of ferroelectrics is anticipated to generate internal electric fields, enhancing chemisorption with heteropolar reactive. The observed high cyclic stability further validates the efficacy of these composite cathodes in mitigating the polysulfide shuttle effect, offering promising prospects for advancing Li-S battery technology.

Between a vineyard and the foliage wall of an adjacent forest, 25 traps containing different Drosophila attractants were applied on three occasions in autumn after the grape harvest. The attractant liquid was Pinot Blanc grape juice to which pure Saccharomyces cerevisiae yeast had been added to initiate fermentation. The five test variants differed in only one characteristic, namely the fermentation time, which was changed in two-day steps. Nine species of the genus Drosophila were captured, but only two were abundant enough to allow statistical analysis of variant differences in capture frequencies. Both species, D. suzukii and D. simulans, can affect the quality of the berries and ultimately the wine even before the harvest and are therefore considered pests. The studies showed that fermenting grape juice is significantly more attractive to both species than unfermented grape juice and that the attractiveness of the attractant liquid is maximised for D. simulans males with a fermentation time of seven to eight days.Parallel to this experiment, an analysis of the aroma spectrum of the fermenting grape juice was carried out with a temporal resolution of one day for the first twenty days. This made it possible to identify the aroma substances that had the highest concentrations in the time frame in which the attractant was particularly attractive and whose attractant effect should therefore be investigated further.

This conceptual paper explores the potential of integrating Electromagnetic Fields (EMF) with traditional physiological signals to enhance emotional contagion in Human-Robot Interaction (HRI). A focused literature review identifies gaps in current HRI models that rely solely on visual, auditory, and known physiological cues for emotional exchange. A novel framework is proposed, incorporating EMF as a complementary modality, aiming to deepen emotional synchronization between humans and robots. The paper lays groundwork for future research to consider EMF detection as a complementary modality alongside traditional cues. It also addresses technological requirements and discusses potential limitations. By extending the modalities used in emotional contagion, this work seeks to advance the development of more intuitive and empathetic robotic systems.

Metal-reinforced polymethyl-methacrylate (PMMA) is considered the gold standard material for immediate loading on dental implants. However, mechanical problems under loading cycles can occur, such as fractures. To overcome these drawbacks, a novel polymer-based material has been proposed. The aim of the present in vitro comparative research is to validate a novel composite polymer developed to replace metal-reinforced PMMA interim restoration due to its advantages of good mechanical proprieties, easier manufacturing, and handling. Ten interim restorations were CAD/CAM designed and fabricated (five in the composite "ONLY" group, and five in the metal-reinforced PMMA group). All the samples were screwed into the prototype models, simulating a complete edentulous mandible rehabilitated with six straight implants. Outcome measures were breakpoint (load, N) and displacement (mm) thought a static, compression test and material behavior under dynamic cyclic test method (fatigue test). A total of twenty samples were tested. Ten samples were used for each test (10 for static and 10 for dynamic), five samples were used in each group (test and control). All the specimens completed the mechanical tests, as planned. There was no statistically significant difference between groups for all, breakpoint, displacement and fatigue tests. Breakpoint in the test group was 1953.19 ± 543.73 N, while, it was 2031.10 ± 716.68 N in the control group, with no statistically significant difference (P=0.775). The displacement was 1.89 ± 0.34 mm in the test group and 1.98 ± 0.75 mm in the control group, again, with no statistically significant difference (P=0.763). Under dynamic cyclic test method, in the control group the mean load was 2504.6 ± 972.15 N, while, in the test group the mean load was 3382 ± 578.5 N. The difference between group was 877.4 ± 579.3 N (p value=0.121). With the limitation of this in vitro study, the novel composite polymer can be used to immediately load dental implants. Further clinical researches are needed to confirm this preliminary results.

This paper comprehensively reviews sensors and sensing devices developed or/and proposed so far utilizing two smart materials: electrorheological fluids (ERFs) and magnetorheological materials (MRMs) whose rheological characteristics such as stiffness and damping can be controlled by external stimuli, an electrical voltage for ERFs and a magnetic field for MRMs, respectively. In this review article, the MRMs are classified into magnetorheological fluid (MRF), magnetorheological elastomer (MRE) and magnetorheological plastomer (MRP). To easily understand the history of sensing research using the two smart materials, the order of this review article is organized in a chronological manner of ERF sensors, MRF sensors, MRE sensors and MRP sensors. Among many sensors fabricated from each smart material, one or two sensors or sensing devices are adopted to discuss on the sensing configuration, working principle and specifications such as accuracy and sensitivity. Some sensors adopted in this article include force sensor, tactile device, strain sensor, wearable bending sensor, magnetometer, display device and flux measurement sensor. After briefly describing what have been reviewed in a conclusion, several challenging future works, which should be done for practical applications as sensors or sensing devices, are remarked in terms of new technologies such as artificial intelligence neural network in which several parameters affecting the sensor signals can be precisely tuned or controlled. It is sure that this review article is very helpful to make creative sensors using not only the proposed smart materials but also several different types of smart materials including shape memory alloys and active polymers.

Abstract: Thermostability of vaccines, particularly enveloped viral vectored vaccines, remains a challenge for their delivery wherever needed. Freeze-drying of viral vectored vaccines is a prom-ising approach but remains challenging due to the water removal process from the outer and in-ner parts of the virus. In the case of enveloped viruses, freeze-drying induces increased stresses on the envelope, which often leads to inactivation of the virus. In this study, we design a method to freeze-dry a recombinant Vesicular Stomatitis Virus (VSV) expressing the SARS-CoV-2 spike glycoprotein. Since the envelope of VSV is composed of 50% lipid and 50% protein, the formula-tion study focused on both the protein and lipid portions of the vector. Formulations were pre-pared primarily using sucrose, trehalose, and sorbitol as cryoprotectants; mannitol as a lyopro-tectant; and histidine as a buffer. Initially, the infectivity of rVSV-SARS-CoV-2 and cake stability were investigated at different final moisture contents. High recovery of the infectious viral titer ( 0.5 to 1 log loss) was found at 3-6% moisture content with no deterioration of the freeze-dried cakes. To further minimize infectious viral titer loss, the composition and concentration of the ex-cipients were studied. An increase from 5 to 10% of both cryoprotectants and lyoprotectant, to-gether with the addition of 0.5% gelatin, resulted in the improved recovery of infectious virus titer and stable cake formation. Moreover, the secondary drying temperature of the freeze-drying pro-cess showed a significant impact on the infectivity of rVSV-SARS-CoV-2. The infectivity of the vector declined drastically when the temperature was raised above 20°C. Throughout a long-term stability study, formulations containing 10% sugar (sucrose/trehalose), 10% mannitol, 0.5% gelatin, and 10 mM of histidine showed satisfactory stability for six months at 2-8°C. The development of this freeze-drying process and the optimized formulation minimizes the need for a costly cold chain distribution system.

The criteria of “Distinctness, Uniformity and Stability” as well as a high "overall quality index” are used to register the Italian modern varieties to the national register. Differently, local conservation varieties can be certified under different EU Directives having, as overall objective, the preservation of biodiversity and the containment of genetic erosion. In recent years, products derived from an-cient grains are perceived to be healthier and more sustainable by consumer, especially in Italy, with consequent higher market prices. Ancient tetraploid wheat varieties registered in the national reg-ister of conservation varieties are 28, 24 of which are Sicilian. They are supposed to have a wide genetic variability compared to modern ones, making them vulnerable of fraud because they are difficult to trace. It is therefore important to have tools able to discriminate the autochthonous Si-cilian varieties. This can be done by gluten proteins composition, which also gives information on the technological properties of derived products. Fifty-one accessions belonging to 22 ancient va-rieties of Sicilian tetraploid (mostly durum) wheat were analyzed. Although a wide intra-accession and intra-varietal variability was assessed, the gliadin pattern of bulks of seeds belonging to each variety was discriminatory. Moreover, differences in technological attitudes were found between landraces. This paves the way to use gluten protein patterns for traceability allowing local farmers and producers to valorize their products and assure consumers about the transparency of the entire supply chain.

The study aimed to evaluate for the first time the degree of contamination of soil and crops with major and trace elements (Cd, Co, Cr, Cu, Ni, Pb, Zn, F, Na, Mg, Si, P, Cl, Fe, Al) in agricultural lands situated in the Lower Danube Basin, Galati and Braila counties (SE Romania), impacted by the steel industry. Soil samples from two depths (0–5 cm and 5–30 cm), as well as leaves and seeds of wheat, corn, and sunflower, were collected from 11 different sites. Along with elemental and mineralogical analysis, performed by HR-CS AAS, PIGE, SEM-EDX and ATR-FTIR, the soil pH, texture, organic matter, electric conductivity and CaCO3 content were investigated. The results showed that the levels of Cr (83.270–383.100 mg kg-1), Cu (17.110–68.151 mg kg-1), Ni (30.157–55.656 mg kg-1), and F (319–544 mg kg-1) in soil exceeded the Romanian regulations for sensitive use of the land. The pollution indices (Igeo, EF, PI, PERI) indicate that the soil is moderate to highly contaminated with Cr, Ni and Cu, while CSI and mERMQ indices suggested a relatively low risk for metal contamination. The concentrations of elements in plant tissues and bioaccumulation factors (BFs) show the soil-plant relation and health risk, but also the elemental selectivity of vegetal compartments. Thus, the results showed that wheat plants tend to exclude the bioaccumulation of certain elements in their tissues, while for Zn and Cu, the bioaccumulation pattern is different. In the case of corn, most BFs were below 1, indicating limited phytoaccumulation capacity. However, exceptions were observed for Cd, Zn, and Cu. Sunflower BFs indicate higher bioconcentration of Cu, Cd, and Zn in both the leaves and seeds compared to other elements. Chromium (Cr) contributes to non-carcinogenic dermal contact and ingestion hazards, with children being more susceptible to the adverse effects of this contaminant.

With the global objectives of achieving a ‘carbon peak’ and ‘carbon neutrality’, along with the implementation of carbon reduction policies, China’s industrial structure has undergone significant adjustments, resulting in constraints on high-energy consumption and high-emission industries while promoting the rapid growth of green industries. Consequently, these changes have led to an increasingly complex power system structure and presented new challenges for electricity demand forecasting. To address this issue, this study proposes a 24-step multivariate time series short-term load forecasting algorithm model based on KNN data imputation and BiTCN bidirectional temporal convolutional networks combined with BiGRU bidirectional gated recurrent units and attention mechanism. The Kepler adaptive optimization algorithm (KOA) is employed for hyperparameter optimization to effectively enhance prediction accuracy. Furthermore, using real load data from a wind farm in Xinjiang as an example, this paper predicts the electricity load from January 1st to December 30th in 2019. Experimental results demonstrate that our comprehensive short-term load forecasting model exhibits lower prediction errors and superior performance compared to traditional methods, thus holding great value for practical applications.

Object detection is complex and involved diverse requirements for different applications. In critical application such as visual impaired navigation guide and real-time surveillance for instance, identifying a particular object of instance is required and this involved a complex approach for realization. Literatures were reviewed, starting with the application of deep learning techniques for object detection; their gaps were identified and addressed using real-time object detection models literature review. From the review gaps were also detected and addressed using literature review on occlusion detection techniques. Object of instance detection in clustered scene with similar object of interest was identified as an open gap not addressed in the existing literature; even through it is vital for many applications. This research recommended an Occlusion Based Object of Instance Detection (OBOID) technique which used the spatial information to identify instant object of interest in clustered scene with many similarly object of interest. Limitation of the recommended OBOID is that it requires only system where position and distance of object is necessary to inform other decision.

An optical fiber scale sensor based on the detection principle of surface plasmon resonance (SPR) was developed for the rapid, high-sensitivity real-time evaluation of scale precipitation from geothermal fluids. The optical fiber SPR scale sensor was fabricated by depositing a gold thin film on the surface of an optical fiber with an exposed core. The optimal gold film thickness of the sensor was determined to be 30 nm, which achieved a refractive index sensitivity of 2140 nm per refractive index unit. A field test was conducted using geothermal brine from the Obama Binary Geothermal Power Plant in Unzen, Nagasaki Prefecture. A conventional optical fiber scale sensor and the SPR sensor were simultaneously assessed using raw and pH-adjusted brines. For the SPR sensor, a peak shift of 0.27 nm/min was observed at a response time of 1 min, whereas no change in transmittance was observed for the conventional sensor until 180 min. After the experiments, scanning electron microscopy–energy-dispersive spectroscopy analysis was conducted on the sensors, and findings showed that the deposition of Mg–SiO2 scale did not significantly differ between the two sensors. The developed SPR sensor achieved faster scale precipitation detection (tens of minutes to hours) than the conventional sensor.

As technology advances, people are increasingly adopting IoT (Internet of Things) devices in smart cities. These devices are equipped with sensors that are connected everywhere, from energy infrastructure and transportation to telecommunications, health and human services, waste management, public safety, and more. People want to access sensor data anytime and everywhere to make better decisions and improve their lives. To achieve this, a sensor integration model has been developed where multiple sensors are integrated under one gateway to manage and share sensor data. However, effective sharing of sensor data requires data security, privacy, confidentiality, fairness, effective architectural design, and low communication and computation costs. These issues need to be addressed in the sensor integration model in smart cities. Existing storage models face challenges in managing sensor data effectively. To overcome these issues and hurdles, a data storage framework leveraging blockchain technology has been proposed within the sensor integration model. This framework ensures data security, privacy, confidentiality, and a fair and transparent financial model, all while minimizing communication and computation costs.

Developing short-term forecasting model for global atmospheric temperature and wind in the near space is crucial for understanding atmospheric dynamics and supporting human activities in this region. While numerical models have been extensively developed, deep learning techniques have recently shown promise in improving atmospheric forecasting accuracy. In this study, convolutional long short-term memory (ConvLSTM) and convolutional gated recurrent unit (ConvGRU) neural networks were applied to build for short-term global-scale forecasting model of atmospheric temperature and wind in the `near space based on the MERRA-2 reanalysis dataset from 2010-2022. The model results showed that the ConvGRU model outperforms the ConvLSTM model in the short-term forecast results. The ConvGRU model achieved a root mean square error in the first three hours of approximately 1.8 K for temperature predictions, and errors of 4.2 m/s and 3.8 m/s for eastward and northward wind predictions, respectively.

The fish supply chain (FSC) industry faces a significant challenge in terms of maintaining fish quality and authenticity throughout the chain. The main goal of modern FSC systems is tracking and tracing the fish product at each stage, from harvester to end customer, as well as assessing its quality and authenticity. Integrating FSC with new technologies, such as Blockchain (BC), Big Data, Artificial intelligence (AI), and Internet of Things (IoT), enhances fish product traceability, authenticity, visibility, and security. We propose a BC-based FSC framework that follows a layered architecture consisting of a SC layer, an IoT layer, and a BC layer. We integrate a new AI-based hand-held device, a Quality, Adulteration & Traceability (QAT) device, that can identify fish species and assess fish quality. We leverage the key features of BC and smart contracts, deployed over the Ethereum platform for the proposed framework integrated with QAT technology. Extensive validation of smart contracts is conducted to prove its practical feasibility.

Maintaining the optimal microclimate in broiler houses is crucial for bird productivity, yet enabling efficient temperature control remains a significant challenge. This study developed and validated a computational fluid dynamics (CFD) model to predict temporal changes in indoor air temperature in response to variable ventilation operations in a commercial broiler house. The model accurately simulated air velocity and airflow distribution for different numbers of tunnel fans in operation, with air-velocity errors ranging from -0.22 to 0.32 m s-1. The predicted airflow rates through inlets and cooling pads showed good agreement with measured values with an accuracy of up to 108.1%. Additionally, the CFD model effectively predicted temperature dynamics, accounting for chicken heat production and ventilation effect. The model successfully predicted the longitudinal temperature gradients and their variations during ventilation cycles, validating its reliability through comparison with experimental data. The study also explored different variable inlet configurations to mitigate the temperature gradient. The variable inlet adjustment showed the potential to relieve the high temperatures but may reduce overall ventilation efficiency or intensify temperature gradients, which confirms the importance of optimising ventilation strategies. This CFD model provides a valuable tool for evaluating and improving ventilation systems and contributes to enhanced indoor microclimates and productivity in poultry houses.

Floods are a common natural disaster whose severity in terms of duration, water resource volume, peak and accumulated rainfall-based damage are likely to differ significantly for different geographical regions. In this paper, we first propose a novel hourly flood index (SWRI24−hr−S), derived from normalising the existing 24-hourly water resources index (WRI24−hr−S) in literature, to monitor flash flood risks on an hourly scale. The proposed SWRI24−hr−S is adopted to identify a flood situation and derive its characteristics, such as the duration (D), volume (V) and peak (Q). The comprehensive result analysis establishes the practical utility of SWRI24−hr−S in identifying flood situations at seven study sites in Fiji between 2014 and 2018 and deriving their characteristics (i.e., D, V, and Q). Secondly, this study develops a vine copula-probabilistic risk analysis system that models the joint distribution of flood characteristics (i.e., D, V, and Q) to extract their joint exceedance probability for the seven study sites in Fiji, enabling probabilistic flood risk assessment. The vine copula approach, particularly suited to Fiji’s study sites, introduces a novel probabilistic framework for flood risk assessment. The results show moderate differences in the spatial patterns of joint exceedance probability of flood characteristics in different combination scenarios generated by the proposed vine copula approach. In the worst-case scenario, the probability of any flood event occurring where the flood volume, peak and duration are likely to exceed the 95th-quantile value (representing an extreme flood event) is found to be less than 5% for all study sites. The proposed hourly flood index and the vine copula approach can be feasible and cost-effective tools for flood risk monitoring and assessment. The methodologies proposed in this study can be applied to other data-scarce regions where only rainfall data is available, offering crucial information for flood risk monitoring, assessment, and the development of effective mitigation strategies.

Introduction: The academic landscape is increasingly recognizing the complex interplay of personal and professional responsibilities on scholarly productivity. For women scholars, particularly those with significant parenting duties, this balance is even more precarious. This study aims to explore how family responsibilities, personal vulnerabilities, and motivational theories such as Imposter Syndrome and Self-Determination Theory (SDT) influence the motivation to publish scholarly work. Understanding these dynamics is crucial for developing supportive mechanisms that can enhance academic productivity and personal fulfilment. Methods: Utilizing a Qualitative Evidence Synthesis (QES) framework, this study will systematically review and synthesize qualitative research on women scholars' experiences in academia, focusing on the challenges and motivators related to publishing. Data sources will include academic databases, grey literature, and first-hand narratives. Thematic analysis will be employed to identify key themes and patterns across the collected data. Results/Findings: Preliminary findings suggest that the dual demands of parenting—especially in extreme cases such as assuming responsibility for seven children—and academic work significantly impact women scholars' publishing activities. Personal vulnerabilities, including imposter syndrome and low self-efficacy, further exacerbate these challenges. However, the data also highlight resilience strategies and the potential for intrinsic and extrinsic motivational factors to mitigate these effects. Discussion: The study underscores the nuanced impact of familial and personal factors on academic motivation. The preliminary findings suggest that addressing imposter syndrome and enhancing self-determination could be pivotal in supporting women scholars. The role of institutional policies and academic culture in either exacerbating or alleviating these challenges is also discussed. Significance: By elucidating the specific challenges and motivators for women scholars in publishing, this study will contribute to the development of targeted interventions and policies that support work-life integration and promote academic productivity. The insights that will be gained could inform mentorship programs, institutional support systems, and policy reforms aimed at fostering a more inclusive and supportive academic environment.

This study comprehensively explores Serbia's Disaster (Risk) Management System, aiming to critically evaluate its inherent strengths and weaknesses. Using descriptive-analytical methods and qualitative interpretation, SWOT analysis was applied to collect data from scientific papers, books, and institutional reports. This study delves deeply into the nuances of Serbia's Disaster Management Framework, revealing a nuanced landscape of strengths, weaknesses, and strategic improvement opportunities. Identified strengths underscore a robust foundation characterized by proficient professionals, state-of-the-art technology, and cohesive teamwork, all pivotal for effective emergency preparedness and response. Conversely, weaknesses underscore pressing imperatives for enhancements in regulatory enforcement, resource allocation, and infrastructure upgrades, presently hampering the framework's efficacy and response readiness. This research contributes to the ongoing discourse on disaster risk management and serves as a catalyst for further scholarly inquiry and policy formulation. By mapping out the structure of Serbia’s Disaster (Risk) Management Framework and integrating diverse data sources, the study enriches theoretical models and lays the groundwork for practical policy interventions. Its findings, including precise recommendations for policy reform and strategic improvements, provide valuable insights for policymakers, emergency management experts, and stakeholders seeking to enhance disaster preparedness and response capabilities on both national and global scales.

With the significant annual increase in the market demand for biopesticides, the industrial production demand for predatory mites, which hold the largest market share among biopesticides, has also been rising.To achieve efficient and low energy consumption control of predatory mite breeding environmental parameters, accurate estimation of breeding environmental parameters is necessary. This paper collects and pre-processing hourly time-series data of temperature and humidity from industrial breeding environments. Time series prediction models such as SVR, LSTM, GRU, and LSTNet are applied to model and predict historical data of the breeding environment. Experiments validate that the LSTNet model is more suitable for such environmental modeling. To further improve prediction accuracy, the training data for the LSTNet model is enhanced using hierarchical clustering of time-series features. After augmentation, the root mean square error (RMSE) of temperature prediction decreased by 27.3%, and the RMSE of humidity prediction decreased by 32.8%, significantly improving the accuracy of multi-step predictions and providing substantial industrial application value.

Introduction: Intrauterine fetal death (IFD) is death of fetus after the 20th week of gestation. Despite regular monitoring, the incidence of IFD remains high. This study aims to assess the incidence and risk factors for IFD in term pregnancies for better prevention and reduction of neonatal morbidity and mortality. Materials and Methods: A retrospective cohort study was conducted with term pregnant women diagnosed with IFD. The analysis included the number of deliveries, live births, and stillbirths. Statistical analysis involves descriptive and analytical statistical methods. Results: Average age was 30 years. Most patients had intermediate and high education, and one-third of patients had regular pregnancy monitoring. 53.33% were primiparous, and pregnancies occurred spontaneously. IFD mainly occurred in the 39th week of gestation. The average birth weight was approximately 3000g. 38.3% had one to two associated diseases, 5% more than three, and 56.7% were healthy. Recurrence of IFD was reported by 10% of patients, while 8.33% had a history of spontaneous abortion. Over 80% of placental histopathological findings indicated some pathology (infarction, infections, abruptio placenta). Conclusion: The most significant risk factors were pregnancy-induced hypertensive disorders, obesity, and diabetes, followed by hypothyroidism, maternal tachycardia, and anemia.

In this study, we evaluate the nonlinear dynamics of convection flow using the thermodynamic variational principle, focusing on scenarios where multiple external forces, such as a thermal gradient and rotational field, are applied to a shallow annular pool. We observed that with the increase in the thermal gradient, the flow changed from an axial flow to a rotational oscillatory flow with the wave amplitudes aligned. Further increasing the temperature difference led to a rotational oscillatory flow characterized by alternating wave generation and annihilation. Our analysis of the flow, considering heat fluxes orthogonal to the thermal gradient, allowed us to describe the flow state as a phase at equilibrium. The state transition of the flow was accompanied by a discontinuous jump in the heat flux, which occurred at the intersection of the entropy production curves.

Retiring coal power plants can reduce air pollution and health damages. However, the spatial distribution of those impacts remains unclear due to complex power system adjustments and pollution chemistry and transport. Focusing on coal retirements in Pennsylvania (PA), we analyze six counterfactual scenarios for 2019 that differ in retirement targets (e.g., reducing 50% of coal-based installed capacity vs. generation) and priorities (e.g., closing plants with higher cost, closer to Environmental Justice Areas, or with higher CO₂ emissions). Using a power system model of the PJM Interconnection, we find that coal retirements in PA shift power generation across PA and the Rest of PJM region leading to scenario-varying changes in the plant-level release of several air pollutants. Due to air pollution chemistry and transport and socio-demographics, these changes in turn give rise to a reduction of 10 to 182 PM_2.5-attributable deaths in PJM across the six scenarios, with most reductions occurring in PA. Scenarios that reduce more coal power generation yield greater aggregate health benefits due to air quality improvements in PA and adjacent downwind regions. In addition, vulnerable populations—in both PA and Rest of PJM—benefit most in scenarios that prioritize plant closures in PA near Environmental Justice Areas. These results demonstrate the importance of considering cross-regional linkages and socio-demographics in designing equitable retirement strategies.

(1) Background: Sleep disordered breathing represent a growing public health concern, especially among children and adolescents. Full-night polysomnography is considered the gold standard for diagnosing obstructive sleep apnea. Our goals are to identify personal and environmental risk factors for the onset and persistence of sleep respiratory disorders. We also want to investigate the differences in neuropsychological profiles; (2) Methods: This is an observational, retrospective cohort study. We collected information on adenoidectomy or adenotonsillectomy. We reviewed the clinical history and preoperative visits and collected data through a telephone questionnaire. Pediatric Sleep Questionnaire (PSQ) and the Pediatric Quality of Life Inventory (PedsQL) are questionnaires used for screening sleep respiratory disorders in children. The data were statistically analyzed it using SPSS version 22.0 for Windows (SPSS Inc., Chicago, IL); (3) Results: The study involved 138 patients, but only 100 parents participated. A higher percentage of patients with sleep disordered breathing were observed to have mothers who smoked during pregnancy. A smaller proportion of patients with sleep disordered breathing had a habit of using a pacifier. A rise in physical results is associated with a reduction in the PSQ at follow-up (p=0.051). An increase of overall academic achievement is associated with an average decrease in the PSQ at follow-up (p<0.0001). A more significant proportion of patients undergoing adenotonsillectomy were observed to have a history of prematurity and cesarean birth (4) Conclusions: These results provide essential information on the effectiveness and effects of adenotonsillectomy intervention compared to adenoidectomy intervention and the factors associated with SDB in children undergoing these interventions.

GvHD still remains, despite the continuous improvement of transplantation platforms, a fearful complication of transplantation from allogeneic donors. Being able to separate GvHD from GvL represents the greatest challenge in the allogeneic transplant setting. This may be possible through continuous improvement of cell therapy techniques. In this review, current cell therapies are taken into consideration which are based on the use of TCR alpha/beta depletion, CD45 RA depletion, T regulatory cells enrichment, NK cell-based immunotherapies and suicide gene therapies in order to prevent GvHD and maximally amplify the GvL effect in the setting of haploidentical transplantation.

A typical orchard's mechanical operation consists of three or four stages: lining, digging for plantation, moving the seedling from nurseries to the farm, moving the seedling to the planting hole, and planting the seedling in the hole. However, the digging the planting hole is the most time-consuming operation. In fruit orchards, robots' usage is increasingly becoming more prevalent to increase operational efficiency. They offer practical and effective services to both industry and people, whether they are assigned to plant trees, reduce the use of chemical fertilizers, or carry heavy loads to relieve staff. Robots can operate for extended periods of time and can highly adept at repetitive tasks like planting many trees. The present study aims to identify the locations for planting trees in orchards using geographic information systems (GIS), to develop an autonomous drilling machine and use the developed robot to open planting holes. There isn't a comparable study on autonomous hole planting in the literature in this regard. The agricultural mobile robot is a four wheeled nonholonomic robot with differential steering and forwarding capability to stable target positions. The designed mobile robot can be used in fully autonomous, partially autonomous, or fully manual modes. The drilling system, which is a y-axis shifter driven by a DC motor with reducer includes an auger with a 2.1 HP gasoline engine. SOLIDWORKS software was used for designing and drawing of the mobile robot and drilling system. The Microsoft Visual Basic.NET programming language was used to create the robot navigation system and drilling mechanism software. The cross-track error (XTE), which determines the distances between the actual and desired holes positions, was utilized to analyze the steering accuracy of the mobile robot to the drilling spots. Consequently, the average of the arithmetic means was determined to be 4.35 cm, and the standard deviation was 1.73 cm. This figure indicates that the suggested system is effective for drilling plant holes in orchards.

Our study aimed to identify predictors for the effectiveness of tumor regression in lung cancer patients undergoing neoadjuvant treatment and cancer resections. Patients admitted between 2016 and 2022 were included in the study. Based on the histology of the tumor, patients were categorized into lung adenocarcinoma group (LUAD), and squamous cell carcinoma group (SQCA). Ninety-five patients with non-small cell lung cancer were included in the study. Fifty-eight (61.1%) and 37 (38.9%) patients were included in the LUAD and SQCA groups, respectively. Nine (9.5%), 56 (58.9%), and 30 (31.6%) patients were categorized with a tumor regression score of I, II, and III respectively. In multivariable analyses, histology of the primary tumor (SQCA), lymph node size in the preoperative CT scan (>1.7cm) and absolute tumor size reduction after neoadjuvant treatment (>2.6 cm) independently predict effectiveness of tumor regression (OR, [95% Confidence interval, p-value] of 6.88 [2.40-19.77, p70 years, extended resection >one lobe, and tumor recurrence or metastasis were identified as significant independent predictors of reduced overall survival. Assessment of tumor size before and after neoadjuvant treatment might help to identify high-risk patients with decreased survival and to improve patient management and care.

Ethical considerations regarding our treatment of animals have gained strength, leading to legislation and a societal focus across various disciplines. This is a subject of study within curricula related to agri-food sciences. The aim was to determine the perceptions of agronomy university students concerning animal welfare in livestock production systems. A survey was conducted to encompass various aspects, from participants' sociodemographic attributes to their attitudes and behaviors regarding animal welfare and the consumption of animal products. Statistical analysis, performed using R software, delved into the associations between participants' characteristics and their perspectives on the ethical, bioethical, and legal dimensions of animal welfare. Associations between demographic factors and ethical viewpoints among students were identified. Gender differences emerged in animal treatment perceptions, while rural and urban environments impacted perspectives on various animals. Bioethical considerations revealed distinctive disparities based on gender and education in concerns for animal welfare, value perceptions, evaluations of animal behaviors, and opinions on animal research. It is crucial to distinguish between animal welfare and ethical considerations arising from coexisting with sentient beings capable of experiencing suffering. Ethical theories provide a lens through which we perceive our obligations toward animals. The responsibility to ensure animal welfare is firmly rooted in recognizing that animals, like humans, experience pain and physical suffering. Consequently, actions causing unjustified suffering or mistreatment, particularly for entertainment purposes, are considered morally unacceptable.

Numerous image processing techniques (IPTs) have been employed to detect crack defects, offering an alternative to human-conducted onsite inspections. These IPTs manipulate images to extract defect features, particularly cracks in surfaces produced through Additive Manufacturing (AM). This article presents a vision-based approach that utilizes deep convolutional neural networks (CNNs) for crack detection in AM surfaces. Traditional image processing techniques face challenges with diverse real-world scenarios and varying crack types. To overcome these challenges, our proposed method leverages CNNs, eliminating the need for extensive feature extraction. Annotation for CNN training is facilitated by LabelImg without the requirement for additional IPTs. The trained CNN, enhanced by OpenCV preprocessing techniques, achieves an outstanding 99.54% accuracy on a dataset of 14,982 annotated images with resolutions of 1536 × 1103 pixels. Evaluation metrics exceeding 96% precision, 98% recall, and a 97% F1-score highlight the precision and effectiveness of the entire process.

Warming of the climate system is unequivocal, and many of the observed changes are unprecedented over five decades to millennia. Globally the atmosphere and ocean is increasingly getting warmer, the amount of ice on the earth is decreasing over the oceans, and the sea level has risen. According to Intergovernmental Panel on Climate Change, the total increasing temperature globally averaged combined land and surface between the average of the 1850-1900 period and the 2003 to 2012 period is 0.78 °C (0.72 to 0.85). But should we prepare for such the relatively small change? The importance is not the mean of the warming but the considerable likelihood of climate change that could trigger extreme natural hazards. The impact and the risk of climate change associated with railway infrastructure have not been fully addressed in the literature due to the difference in local environmental parameters. On the other hand, the current railway network in Malaysia, over the last decade, has been significantly affected by severe weather conditions such as rainfall, lightning, wind and very high temperatures. Our research findings point out the extremes that can lead to asset system failure, degraded operation and ultimately, delays to train services. During the period of flood, the embankment of the track can be swept away and bridge can be demolished, while during drought, the embankment of the track can suffer from soil desiccation and embankment deterioration, high temperature increases the risk of track buckling and high winds can result in vegetation or foreign object incursion on to the infrastructure as well as additional quasi-static burden exerted. This review is of significant importance for planning and design of the newly proposed high speed rail link between Malaysia and Singapore.

Lower cutoff levels in screening programs have led to an increase in the proportion of detected cases with transient hypothyroidism, leading to increase of the overall incidence of primary congenital hypothyroidism (CH) in several countries. We have performed retrospective evaluation on the data from 251,008 (96.72%) neonates screened for thyroid-stimulating hormone (TSH) level in dried blood spot specimens taken 48 hours after birth, between 2002 and 2015, using DELFIA method. A TSH value of 15 mIU/L was used as the cutoff point until 2010 and 10 mIU/L thereafter. Primary CH was detected in 127 newborns (1/1976) of which 81.1% had permanent and 18.9% had transient CH. The incidence of primary CH was increased from 1/2489 until to 2010 to 1/1585 thereafter (p=0.131). However, the incidence of permanent CH was slightly increased (p=0.922), while the transient CH incidence had 8-fold increasing after lowering the TSH cutoff level (p<0.001). In cases with permanent CH, we observed lower frequency for thyroid dysgenesis (82.7 vs. 66.7%) and higher frequency for normal in-situ thyroid gland (17.3 vs. 33.3%), for the period with reduced TSH cutoff value. Our findings support the impact of lower TSH cutoff on the increasing incidence of congenital hypothyroidism.

A reinforcement learning algorithm is proposed to improve the accuracy of short-term load forecasting (STLF) in this article. The proposed model integrates radial basis function neural network (RBFNN), support vector regression (SVR), and adaptive annealing learning algorithm (AALA). In the proposed methodology, firstly, the initial structure of RBFNN is determined by using SVR. Then, an AALA with time-varying learning rates is used to optimize the initial parameters of SVR-RBFNN (AALA-SVR-RBFNN). In order to overcome the stagnation for searching optimal RBFNN, a particle swarm optimization (PSO) is applied to simultaneously find promising learning rates in AALA. Finally, the short-term load demands are predicted by using the optimal RBFNN. The performance of the proposed methodology is verified on the actual load dataset from Taiwan Power Company (TPC). Simulation results reveal that the proposed AALA-SVR-RBFNN can achieve a better load forecasting precision as compared to various RBFNNs.

Continuous technological progress places significant demands on the materials used in increasingly modern devices. An important parameter is often the long-term thermal resistance of the material. The use of heat-resistant polymer materials worked well in technologically advanced products. An economically justified direction in searching for new materials is the area of polymer nanocomposite materials. It is necessary to appropriately select both the polymer matrix and the nanofillers best able to demonstrate the synergistic effect. A promising area of exploration for such nanocomposites is the use of organosilicon polymers, which results from the unique properties of these polymers related to their structure. This review presents the results of the analysis of the most important literature reports regarding organosilicon polymer nanocomposites with increased thermal resistance. Particular attention was paid to modification methods of silicone nanocomposites focused on the increase of their thermal resistance related to the modification of siloxane molecular structure and by making nanocomposites using inorganic additives, carbon nanomaterials. Attention was also paid to such important issues as the influence of the dispersion of additives in the polymer matrix on the thermal resistance of silicone nanocomposites and the possibility of modifying the polymer matrix and permanently introducing nanofillers thanks to the presence of various reactive groups. The thermal stability mechanism of these nanocomposites was also analysed.

Nonlinear single unit activity (SUA) characteristics are the useful measures to reveal the information processing and transfer features associated with Parkinson’s disease (PD) in the basal ganglia. Most of the state-of-the-art approaches to compute such parameters in continuous and discrete forms are strongly dependent on SUA recording length, noise level and input parameters. Due to the specificity of SUA data collection (mainly short recordings with relatively low signal-to-noise ratio) new techniques to evaluate neuronal nonlinear properties are needed. We have developed an encoding technique based on a mean interspike interval (ISI) value to calculate spike train discrete nonlinear features. The approach to compute mutual information (MI) of isolated neurons with its unstructured activity was also proposed. The proposed technique of SUA nonlinear features evaluation slightly depends on spike train length, has low correlations with other SUA characteristics (firing rate, coefficient of ISI variance and asymmetry index). The derived entropy measure in the subthalamic nucleus has significant positive correlation with PD severity. The proposed approach provides nonlinear features that are slightly dependent on investigated sample size and independent on input parameters. Also, the developed mean ISI based measures reflect the more complex nature of oscillatory activity in the basal ganglia, than it was thought previously. Moreover, MI, unlike entropy, takes into account the position of the spike train elements, which allows us to investigate the amount of information retained after the occurrence of temporary failures. The developed approach may be useful in describing nonlinear features of basal ganglia activity contributing to PD pathophysiology probably associated with impaired information transfer in movement disorders.

This paper describes the proposal and development of a proof of concept (PoC) for a data logger system designed for operation and fault detection in bench testing of combustion engines. The main objective was to develop a data logger system that collects data on vibration, sound, temperature, and CO2 levels to identify ignition and combustion faults, thereby contributing to reducing greenhouse gas emissions (GHG). The paper presents (i) the proposal and development and (ii) the open-source code: proof of concept for a data logger system focused on detecting faults and monitoring the operational condition of benchtop combustion engines. The results indicate the feasibility of the PoC for data acquisition and dataset creation for Research and Development purposes.

It is increasingly common for experiments in biology and medicine to involve large numbers of hypothesis tests. A natural graphical method for visualizing these tests is to construct a histogram from the p-values of these tests. In this article, we examine the shapes, both normal and abnormal, that these histograms can take on, as well as present simple inferential procedures that help to interpret the shapes in terms of diagnosing potential problems with the experiment. We examine potential causes of these problems in detail, and discuss potential remedies. Throughout, examples of abnormal-looking p-value histograms are provided and based on case studies involving real biological experiments.

The accurate detection and assessment of stress play a pivotal role in enhancing individual well-being and healthcare outcomes. Traditional methods of stress detection often grapple with limitations in accuracy and scalability. With the advent of machine learning (ML), the potential to revolutionize stress detection has emerged. This paper presents a comprehensive study on the application of ML algorithms for stress detection, with a focus on physiological and behavioral data analysis. Central to our approach is the integration of SHapley Additive exPlanations (SHAP), an Explainable Artificial Intelligence (XAI) technique, to interpret ML models. SHAP provides a novel lens to understand the impact of individual features in the complex decision-making processes of ML models, thereby enhancing the transparency and reliability of stress predictions. We demonstrate how SHAP not only aids in elucidating model decisions but also contributes to refining the models for greater accuracy. Our results highlight the effectiveness of ML in detecting stress and the pivotal role of XAI in making these models more interpretable and trustworthy. This study underscores the synergy between advanced ML techniques and XAI, paving the way for more nuanced and reliable stress detection methodologies that are essential in diverse settings, from healthcare to workplace environments.

A Partial discharge (PD) occurrence in high-voltage (HV) and medium-voltage (MV) power assets is a warning sign of insulation system degradation or defective manufacturing/assembly, that may cause catastrophic damage and eventually lead to the breakdown of the power equipment. Ultra-high frequency (UHF) PD measurement technology has extensively been used to monitor the insulation health of the HV or MV equipment due to its high immunity against ambient noise and conducted disturbances. This paper presents experimental validation of a new design of a UHF planar rectangular microstrip antenna that can be used for PD monitoring of HV and/or MV power equipment, such as power transformers. The designed planar rectangular microstrip antenna has a compact size of 80mmx70mmx1.6mm. Laboratory experiments were performed to validate the antenna sensitivity to PD activity caused by insulation defects created inside an oil-filled transformer tank model. PD measurement results confirm that the proposed rectangular microstrip antenna has high sensitivity and high signal-to-noise ratio (SNR), thanks to its capability to suppress external noise disturbances, especially during online PD monitoring. Thus, the proposed UHF antenna seems to be a promising and alternative PD sensor that can be employed in UHF PD monitoring systems of HV or MV power equipment.

Human papillomavirus (HPV) can potentially compromise both unassisted conception and success rates with assisted reproductive technology (ART). We aimed to evaluate the rates of HPV vaccination among women presenting for fertility care. This was a prospective study analyzing a self-reported intake form completed by all new patients presenting to a fertility clinic. The primary outcome was HPV vaccination status. Among the 523 new patients included in this study 172 (32.9%) were fully vaccinated, 237 (45.3%) were unvaccinated, and 95 (18.2%) patients didn’t respond. There was a significant age difference between fully vaccinated patients (33.1 years) compared to unvaccinated patients (37.4 years) p&lt;0.001 and a significant difference in gravidity between fully vaccinated patients (average 0.65) and unvaccinated patients (average 1.11) p=0.0005. No significant association was found between HPV vaccination status and history of abnormal Pap smears or relationship status (single vs. married). Less than half of patients presenting to our fertility center were vaccinated against HPV, despite being eligible to receive the vaccine. Younger patients with lower gravidity were more likely to be vaccinated against HPV than older patients with higher gravidity. Reproductive Endocrinologists have the opportunity to recommend HPV vaccination for eligible patients presenting for fertility care.

The ribonuclease H (RNase H) active site of HIV-1 reverse transcriptase (RT) is the only viral enzyme not targeted by approved antiretroviral drugs. Using a fluorescence-based in vitro assay, we screened 65,239 compounds at a final concentration of 10 µM to identify inhibitors of RT RNase H activity. We identified 41 compounds that exhibited 50% inhibitory concentration (i.e., IC50) values &lt; 1.0 µM. Two of these compounds, 2-(4-methyl-3-(piperidin-1-ylsulfonyl)phenyl)benzo[d]isothiazol-3(2H)-one (1) and ethyl 2-(2-(3-oxobenzo[d]isothiazol-2(3H)-yl)thiazol-4-yl)acetate (2), which both share the same benzisothiazolone pharmacophore, demonstrate robust antiviral activity (50% effective concentrations of 1.68 ± 0.94 µM and 2.68 ± 0.54, respectively) in the absence of cellular toxicity. A limited structure-activity relationship analysis identified two additional benzisothiazolone analogs, 2-methylbenzo[d]isothiazol-3(2H)-one (3) and N,N-diethyl-3-(3-oxobenzo[d]isothiazol-2(3H)-yl)benzenesulfonamide (4), which also resulted in inhibition of RT RNase H activity and virus replication. Compounds 1, 2 and 4, but not 3, inhibited the DNA polymerase activity of RT (IC50 values ~ 1 to 6 µM). In conclusion, benzisothiazolone derivatives represent a new class of multifunctional RT inhibitors that warrants further assessment for the treatment of HIV-1 infection.

Seeds from several Ribes taxa were surveyed for phenolic compounds and in vitro antiproliferative activity against HT-29 colorectal cancer cells. Total phenolic compounds were analysed through the Folin-Ciocalteu procedure, while phenolic profiles were analysed by LC coupled to a single mass spectrometer Orbitrap using an electrospray interface (ESI). Antitumor effects were established using the MTT (3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide) assay. Total phenolics ranged from 11.4 in R. alpinum to 94.8 mg of caffeic acid equivalents (CAE)/g in R. nigrum 'Koksa'. Concerning phenolic compounds, four were hydroxylated benzoic acids, four cinnamic acid derivatives, eight flavonoids, and nine flavonoid glycosides. The growth inhibition against HT-29 cancer cells was exercised much better by R. nigrum 'Koksa' and Ribes 'Erkeeni' (GI50 37 and 42 µg/ml). All Ribes extracts, except R. nigrum 'Hara katarlik', showed higher activity than that of R. rubrum (GI50 at 72 h: 99 µg/ml). Interestingly, the highly bioactive extract from Ribes 'Erkeeni' contains all detected phenolics, while R. nigrum 'Koksa' lacks only populnin. Therefore, the high bioactivity found for such extracts could be due to a synergy due to all detected compounds. This work constitutes a comprehensive action for expanding knowledge on the phenolic profiles and antitumor activity of GLA-rich Ribes seeds.

Introduction: The trophoblast derived angiogenic factors are considered to play an important role in the pathophysiology of various complications of pregnancy. The aim of this study was to establish relationship between concentrations of soluble Human Leukocyte Antigen-G (sHLA-G) in maternal serum and amniotic fluid at 16-22 weeks of gestation and the sonographic measurements of the fetal and placental growth. Materials and methods: sHLA-G in serum and amniotic fluid, as well as fetal biometric data and placental volume and perfusion indices were determined in 41 uncomplicated singleton pregnancies. Results: The sHLA-G levels were unchanged both in amniotic fluid and in serum during mid-pregnancy. The sHLA-G level in serum correlated positively with amniotic sHLA-G level (β=0.63, p<0.01). Significant correlation was found between serum sHLA-G level and abdominal measurement (β=0.41, p<0.05) and estimated fetal weight (β=0.41, p<0.05). The amniotic sHLA-G level and placental perfusion (VI: β = -0.34, p<0.01 and VFI: β = -0.44, p<0.01, respectively) were negatively interrelated. A low amniotic sHLA-G level was significantly associated with nuchal translucency (r = -0.102, p<0.05). Conclusions: sHLA-G assayed in amniotic fluid might be a potential indicator for placental function, whereas the sHLA-G level in serum can be a prognostic modality for feto-placental insufficiency.

Continuous-flow microwave heating stands out for its ability to rapidly and uniformly heat substances, making it widely applicable in chemical production. However, in practical applications, the permittivity of the heated liquid changes dramatically as the reaction progresses, affecting the efficiency and uniformity of continuous-flow heating. Herein, this work presents a novel microwave heating device based on coaxial structure for high-performance heating. Our approach commenced with the development of a multi-physical field model, incorporating a spiral polytetrafluoroethylene (PTFE) as a water channel and the coaxial waveguide as a container was established. The analysis shows that the uniform distribution of the sectional electric field of electromagnetic waves in the TEM mode within the coaxial structure can enhance heating uniformity. Then, a continuous-flow microwave heating system for different liquid loads was established, and experimental measurements were conducted. The heating efficiency for all loads exceeded 90%, which basely matched the simulation results, validating the accuracy of the model. Finally, the heating efficiency and uniformity under different permittivity loads were analyzed, as well as the impact of channel radius on heating efficiency. The device demonstrated high heating efficiency and stable heating uniformity across different loads. This continuous-flow microwave device is suitable for chemical research and production, contributing to the promotion of microwave energy applications in the chemical industry.

Soil carbon (C) cycling under anoxic conditions is mechanistically linked to dissimilatory iron (Fe) reduction, which could be regulated by exogenous dissolved organic matter (DOM). However, the impact of complex exogenous DOM on soil microbial activity and C-Fe coupling in paddy soils remains underexplored. With a 100-day microcosm experiment, we determined that the molecular composition of DOM derived from organic fertilizers and biochar on paddy soil affects soil microbial community, Fe reduction, and C emissions. Our results indicated that biochar-DOM significantly promoted Fe reduction and accelerated CH₄ and CO₂ emissions, and organic manure-DOM increased soil CO₂ emissions, which was closely related to the molecular composition of exogenous DOM. DOM molecules with high aromaticity (AI_mod) and high DBE, including lignins-vascular plant-derived polyphenols, lignins-polycyclic aromatics (PA), and condensed aromatics-PA, promoted soil Fe reduction and CH₄ emissions by enriching soil Fe-reducing bacteria (FeRB), reducing methanotrophs, and facilitating r-strategists at the early stage of incubation. Conversely, DOMs with low AI_mod, low DBE and high H/C, such as lignins-highly unsaturated and phenolic compounds and proteins-aliphatic compounds, enhanced CO₂ emissions by facilitating recalcitrant C degradation and CH₄ oxidation at the late stage of incubation. In conclusion, our study highlights the importance of the molecular composition of DOMs derived from organic amendments in regulating soil Fe reduction and C emissions. The findings offer novel insights into the effective utilization of agricultural resources and the mitigation of soil C emissions.

In recent years, growing attention has been directed towards the potential of plant extracts as great therapeutic agents in controlling oxidative stress and inflammation. Gymnema inodorum (Lour.) Decne, an indigenous plant locally grown in Northern Thailand, is known for its anti-diabetic activity. This study aims to explore the antioxidant properties and phenolic profile of column chromatographic fractionated G. inodorum leaf extract. The ethanolic-reflux extracts of G. inodorum leaves were subjected to column chromatography for the isolation of bioactive molecules. Total phenolic and flavonoid content were assessed using Folin–Ciocalteu and aluminium chloride colorimetric methods, respectively. Total antioxidant activity was evaluated by employing different antioxidant assays, including 2,2-diphenyl-1-picrylhydrazyl (DPPH), 2,2′-azino-bis-(3-ethylbenzothiazoline-6-sulfonic)acid (ABTS) scavenging assay and ferric reducing antioxidant power (FRAP) assay. High-Performance Liquid Chromatography (HPLC) with a C18 column was employed to determine the level of gymnemic acid, while Liquid Chromatography Quadrupole Time-of-Flight/Mass Spectrometry (LC-QTOF/MS) was used to identify potential phenolic compounds. The three separated fractions indicating A, B, and C, exhibited remarkable antioxidant activity, with total phenolic content of 0.294 ± 0.056, 0.085 ± 0.039, and 0.227 ± 0.041 mg QE/mL, and total flavonoid content of 0.274 ± 0.050, 0.309 ± 0.110, and 0.384 ± 0.007 mg QE/mL, respectively. Fraction A exhibited the highest DPPH and ABTS scavenging activity, while fraction C demonstrated significantly higher ferric-reducing power. HPLC analysis revealed a highest concentration of gymnemic acid in fraction C (0.393 ± 0.003 mg/g) compared to fraction A (0.159 ± 0.003 mg/g) and fraction B (0.142 ± 0.000 mg/g). The LC-QTOF/MS phenolic screening showed seven potential phenolic compounds in fraction A, seven compounds in fraction B, and four compounds in Fraction C. A significant relationship is found between antioxidant potential and total phenolic content, suggesting that phenolic compounds are the major contributors to the antioxidant activity of G. inodorum.

It is extremely fascinating and astonishing that the gravitational field on the surface of a neutron star is with a relativistic mass density of 2.65*10¹⁶~5.87*10¹⁸kgm^-3 which can be larger than the mass density of the neutron star (~10¹⁷kgm^-3).Therefore, it is the author’s first intuitional imagining that this field could directly convert into mass. In so strong a gravitational field, electron and proton could be produced directly from graviton–photon collision. The gravitational field exists in everywhere in our universe. No vacuum that the region of a space is “empty” does exist. A particle is clearly always being acted on by the gravitational field. The quantum vacuum fluctuation and vacuum polarization need be re-understood with the interaction between photon and gravitational field. Therefore, the gravitational field is naturally one of the foundations of modern physics.

Recently, flares have been considered as a major source of air pollution from the petroleum refining industry. The United Nations have instigated an international effort related to the management of flare emissions to reduce the global warming impact related to flaring. Eliminating or removing the need for gas flares is difficult because these devices are generally used as safety devices to allow combustion of flammable gases in a controlled fashion which supports safe operation. However, reducing flaring is generally possible using well designed efficiently operated flare equipment. In general, flare performance can be enhanced following the API-521 methodology and using assist- media including air and steam to achieve smokeless operation. This present work will discuss flare emissions in petroleum refining industry, and a method to manage flare emissions. Moreover, this work will discuss flare Combustion Efficiency (CE) and Distraction and Removal Efficiency (DRE) in terms of efficient flare operation. This work uses actual operating flare data, published previously, will be used in this work together with the CFD Code C3d. This code, developed at the USDOE Sandia National Laboratory is based on a standard LES methodology to conduct transient flare analysis is used to simulate flare operation to estimate flame shape and emissions produced. In this work, a new air-assisted flare tip design which uses the Coanda effect to improve flare operation was analysed. This new flare design reduces the emission rate that demonstrates the design effectiveness. The analysis considers a flare 1m high and (6") diameter in the centre of a 4m*4m*4m domain. Boundary conditions considering no cross wind and an ambient temperature of 300K. The initial condition is a hydrostatic pressure profile across the computational domain. In the air assist simulation, stoichiometric ratio will be a variable and therefore more than one case was considered.

In strawberry cultivation, precise disease management is crucial for maximizing yields and reducing unnecessary fungicide use. Traditional methods for measuring Leaf Wetness Duration (LWD), a critical factor in assessing the risk of fungal diseases such as botrytis fruit rot and anthracnose, have been reliant on sensors with known limitations in accuracy and reliability and difficulties with calibrating. To overcome these limitations, this study introduced an innovative algorithm for leaf wetness detection systems employing high-resolution imaging and deep learning technologies, including convolutional neural networks (CNNs). Implemented at the University of Florida's Plant Science Research and Education Unit (PSREU) in Citra, Florida, USA and expanded to three additional locations across Florida, USA, the system captured and analyzed images of a reference plate to accurately determine the wetness and, consequently, the LWD. The comparison of system outputs with manual observations across diverse environmental conditions demonstrated the enhanced accuracy and reliability of the artificial intelligence-driven approach. By integrating this system into the Strawberry Advisory System (SAS), this study provided an efficient solution to improve disease risk assessment and fungicide application strategies, promising significant economic benefits and sustainability advances in strawberry production.

We investigate solutions of the classical Mathieu-Hill (MH) equation which characterizes the dynamics of trapped ions, based on the Floquet theory and starting from a well known analytical model. The analytical model we introduce demonstrates that the equations of motion are equivalent to those of the harmonic oscillator (HO). Two independent approaches are used, based on two classes of complex solutions of the MH equation. The paper addresses both the damped HO and parametric oscillator (PO) for an ion confined in an electrodynamic (Paul) trap. Stability and instability regions for the periodic orbits associated to the MH equation which describes a HO (PO) confined in an electrodynamic trap are also discussed, depending on the values of the Floquet exponent, for very small values of the $q$ parameter. The main objective of the paper is to identify stable and bounded solutions for the dynamics of a HO levitated in an electrodynamic trap. This paper represents a follow-up of a recently published article in Photonics, 11 (6) 551.

Historically, the military and non-religious, sub-continent’s intellectual elite Muslim men crafted state ideologies before partition, by actively contributing to sociocultural constructs prevalent to this day, in service of colonial patriarchal concepts. The purpose of this ideological collaboration has been to mould a Pakistani cis-gendered female child primarily into the ideal “Pakistan-Muslim” bride for marriage, carried out through her family and society. This has shaped the lives of cis-gendered female children in Pakistan through coerced, gendered control, implemented as prescriptive societal norms. These norms are rooted in colonial, patriarchal ideologies and are functions of capital and coercion intentionally perpetuated to erase her pluralistic identity, reducing her to a central resource within a family unit. To the military concept of nationalism, her mind and her body symbolize the unification and centralization of a statist ideology. Thus, the military state plays an essential role in shaping her purpose around the concept of nationalism. The intellectual elite, via the state, uphold colonial, patriarchal ideologies, where the primary identity of a cis-gendered female child is actualized through her marriage. The cis-gendered female child’s life is a vehicle to unify the state’s two-fold “Pakistani-Muslim” agenda, by implementing a ‘singular statist narrative’. A narrative that attempts to resolve two major tensions: First, it seeks to wipe out the possibility of a nation connecting with and exploring its own immense, internal ethnocultural diversity. It does this by imposing an imagined “homogenous Muslim” identity — which doesn’t exist — and is instead imported from multiple countries to reinforce a ‘singular statist narrative’, Second, it aims to control the mixing of local, sociocultural narratives by bridging any disjuncture between them by labelling colonial institutional patriarchy concepts as inherently “Pakistani”; in service of its preferred ‘singular statist narrative’.

Foot and Mouth Disease (FMD) is a viral disease, widespread and highly contagious affecting mainly cloven-hoofed domestic and wild animals. FMD can lead to high economic losses due to reduction in animals’ production such as drop of milk production, loss of body weight and high mortality rate in young ruminants. Sixteen nasal swabs and epithelial tissues were collected from animals showing typical clinical signs of FMD during the last FMD outbreak in Libya in 2018-2019. Blood samples, swabs and epithelial tissues impressions on Flinders Technology Associates (FTA) cards were shipped to the FMD Reference laboratory in Brescia, Italy, and tested for the detection of FMD viruses. Nucleic acids were extracted from the FTA cards and molecular testing of the examined FTA cards confirmed that the FMD virus circulating in Libya was serotype O. Sequencing analysis of the FMD virus VP1 gene confirmed that FMD virus strain was serotype O/East Africa 3 (O/EA-3) topotype. The phylogenetic of the VP-1 gene of the FMD virus showed very high nucleotide identity (99.8%) between the virus circulating in Libya and the Algerian FMD virus strains isolated in Algeria on 2018 and 2019.

Background: Interstitial lung disease (ILD) is a frequent complication in systemic sclerosis (SSc). So, an increased awareness of this complication is a real need in the clinical setting, because it may affect the prognosis of patients. In particular, an accurate strategy is desirable in order to detect ILD in its stages. So, we investigate the validity of ultrasound (US) in detecting subclinical ILD in SSc, and to determine its potential in disease progression. Methods: 133 patients without respiratory symptoms and 133 healthy controls were included. Borg scale, Rodnan skin score (RSS), pulmonary auscultation, chest radiographs and respiratory function tests (RFT) were performed. An expert rheumatologist performed the lung US. High-resolution CT (HRCT) was also performed. After the baseline assessment, the patients were followed every 3 months for 12 months. Results: A total of 79 of 133 patients (59.4%) showed US signs of ILD in contrast to healthy controls (4.8%) (p=0.0001). The clinical and laboratory variables associated with ILD were anti-centromere antibodies (p=0.005) and RSS (p=0.004). A positive correlation was demonstrated between the US and HRCT findings (p=0.001). Sensitivity and specificity of US in detecting ILD was 91.2% and 88.6% respectively. A good inter-observer reliability was observed (k = 0.72). In the follow-up, a total of 30 patients out of 79 (37.9%) who demonstrated US signs of ILD at baseline, showed changes in the ILD score by US. Conclusions: US showed a high prevalence of subclinical ILD in SSc patients. It demonstrated to be a valid, reliable and feasible tool to detect ILD in SSc and to monitoring the disease progression.

Imperfection sensitivity of large amplitude vibration of curved single-walled carbon nanotubes (SWCNTs) is considered in this study. The SWCNT is modeled as a Timoshenko nano-beam and its curved shape is included as an initial geometric imperfection term in the displacement field. Geometric nonlinearities of von Kármán type and nonlocal elasticity theory of Eringen are employed to derive governing equations of motion of nano-beam. Spatial discretization of governing equations and associated boundary conditions is performed using differential quadrature (DQ) method and the corresponding nonlinear eigenvalue problem is iteratively solved. Effects of value and location of the geometric imperfection, and the nonlocal small-scale parameter on the nonlinear frequency ratio and imperfection sensitivity of a curved SWCNT for various boundary conditions are investigated. The results show that the geometric imperfection plays a significant role in the nonlinear vibration characteristics of curved SWCNTs.

Population growth, climate change, changes to land use, and the advent of emerging infectious disease agents has put our abilities to feed the growing global population at risk, which is of particular concern in low- or middle-income countries. Research to improve the profitability and sustainability of common livestock production systems is key to tackling this issue. However, despite considerable research investment to address this concern, there has been no attention to development of robust methodologies for the synthesis of existing research evidence and its re-use. Syntheses of evidence are critical for fostering best practices, minimising wastage of valuable research resources, and enabling informed decision and policy making. Whilst the use of evidence syntheses is well entrenched in human healthcare, their use within animal sciences is limited and specific methodologies for performing them are underdeveloped. In this call to action, we propose some methodological development activities that should be undertaken within this field of research to increase the potential of evidence syntheses to contribute to tackling pressing societal issues relating to livestock agriculture.

In recent years, organic agriculture has gained more popularity, yet its approach to food production and its potential impact on consumers’ health and various environmental aspects remain to be fully discovered. The goal of organic farming practices is to maintain soil health, sustain ecological systems, maintain fairness in its relationship with the environment and protect the environment in its entirety. Various health benefits have been associated with higher consumption of organic foods. This review identified some of these health benefits including a reduction in obesity and body mass index (BMI), improvements in blood nutrient composition as well as a reduction in maternal obesity and pregnancy-associated preeclampsia risk. Furthermore, organic food consumption can reduce the development of non-Hodgkin lymphoma and colorectal cancers. Upon reviewing existing literature regarding the nutritional value of organic foods, it was found that organic food contained higher levels of iron, magnesium, and vitamin C. However, the evidence available to draw definitive generalizations remains limited. In this review, we provided essential insights to support sustainable organic farming and highlighted the potential of organic food consumption that could play a pivotal role in positively impacting human health.

In the history, architects, engineers or artists traditionally visualized architectural, urban planning, urban design, or landscape design projects with physical models in a smaller scale to represent their ideas. The biggest problems of traditional materialistic models are the long production time and limitation of mobility. Thanks to advancements in digital technology, 3D models can now be generated easily from 2D blueprints using computer software. However, eventually the digitalized approach could not replace the whole industry of making physical models, because of a lack of stereoscopic 3D imaging of space and structures. In this study, we discuss two points: the normal procedure of visualizing 3D models in urbanism and architecture design projects; and proposal of the stereographic hologram visualization for 3D models created with CHIMERA hologram printer as a new approach to solve all the problems in spatial projects visualization of both digitalized and physical models. The experiment's results indicate that tabletop holograms' visualization quality can potentially replace traditional methods in the near future. Moreover, the input data for this method can be seamlessly integrated into current architectural and urban design workflows, making holograms a promising approach for 3D immersive content in this field.

: This paper presents a couple of meal monitoring systems for senile dementia patients by using electronic weight and temperature sensors. These monitoring systems enable to convey the information of the amount of meal taken by the patients in real-time via wireless communication networks onto the mobile phones of their families or nurses in charge. Thereby, the nurses can easily spot the most desperate patient to take care of while the families can have relief to see the crucial information for survival of their parents at least three times a day. Meanwhile, the senile dementia patients tend to suffer the burn of their tongues because they can hardly recognize the temperature of hot meals served and therefore avoid the burn of tongues. This phenomenon can be discarded by utilizing the meal temperature monitoring system which displays alarm to the patients when the meal temperature is above the reference. These meal monitoring systems can be easily implemented by utilizing low-cost sensor chips and Arduino UNO boards so that elder-care hospitals and nursing homes can afford to exploit them with no additional cost. Hence, we believe that the proposed monitoring systems would be a potential solution to provide a great help and relief not only for the professional nursing nurses working in elder-care hospitals and nursing homes, but also for the families of the dementia patients.

Optimal operation of petroleum production is important in a transition from energy systems based on fossil fuel to sustainable systems. One sub-process in petroleum production deals with transport from the (subsea) well-bore to a topside separator. A simple model in [] of Electric Submersible Pump [ESP] lifted production was previously streamlined into a dynamic model suitable for illustration of the dynamics of oil transport, as well for control studies, with some comparison of two popular modeling languages: Modelica, and ModelingToolkit for Julia, []. Here, the discussion on dimensionless equipment models goes into more detail, and the comparison between Modelica and ModelingToolkit is significantly expanded upon with code comparison, numerical performance, and more experiments. Some added possibilities with ModelingToolkit and Julia wrt. sensitivity analysis and control design is included.

The paper interprets a comparison of two mostly used techniques of a field-oriented control for 6-phase electric drives, with their pros and cons, as well as their differences in construction and behaviour. Both of these approaches have been realized. Frequency and step responses analysis have been demonstrated with a 6-phase permanent magnet synchronous machine. Experimental results have been compared with simulations based on a mathematical model.

Continuous casting is the most common method for producing steel into semi-finished shapes like billets or slabs. Throughout this process, steel experiences mechanical and thermal stresses, which influence its mechanical properties. During continuous casting, decreased formability in steel components leads to crack formation and failure. One reason for this phenomenon is the appearance of the soft ferrite phase during cooling. However, it is unclear under which conditions this ferrite is detrimental to the formability. In the present research, we investigated what microstructural changes decrease the formability of microalloyed steels during continuous casting. We studied the hot compression behaviour of microalloyed steel over temperatures ranging from 650 °C to 1100 °C and strain rates of 0.1 s-1 to 0.001 s-1 using a Gleeble 3800® device. We examined microstructural changes at various deformation conditions using microscopy. Furthermore, we implemented a physically-based model to describe the deformation of austenite and ferrite. The model describes the work hardening and dynamic restoration mechanisms, i.e., discontinuous dynamic recrystallisation (dDRX) in austenite and dynamic recovery (DRV) in ferrite and austenite. The model considers the stress, strain, and strain rate distribution between phases by describing the dynamic phase transformation during the deformation in iso-work conditions. Increasing the strain rate below the transformation temperature improves hot ductility by reducing DRV and strain concentration in ferrite. Due to limited grain boundary sliding, the hot ductility improves at lower temperatures (&lt;750 °C). In the single-phase domain, DRX improves the hot ductility provided that fracture occurs at strains in which DRX advances. However, at very low strain rates, the ductility decreases due to prolonged time for grain boundary sliding and crack propagation.

Relevant observations suggest that in geothermal power resources and volcanic regions in Earth the mean heat flow is either comparable or greater than the current global mean heat flow of this planet. We have inferred that critical or minimum heat flow required to sustain geothermal provinces (T >150⁰C) is at least 90 mWm^-2 and the same required to sustain active volcanoes in Earth is at least 100 mWm^-2.The volcanism in Venus is found have declined significantly during the past 300 Ma. It is suggested that Earth may lose significant part of its current active volcanoes and geothermal power resources in the next 300-500 Ma if the global mean heat flow in Earth is decreasing at a rate of 5.76 mW per 100 Ma. At the current inferred maximum rate of mantle cooling (20^o C per 100 Myrs) the plate tectonics in Earth is likely to cease within 750 Myrs from now. The critical mean surface heat flux for sustaining plate tectonics in Earth is inferred to be around 50-55 mW/m².

Background/Objectives: Lung cancer remains a global health concern, with substantial variation in patient survival. Despite advances in detection and treatment, the genetic basis for the divergent outcomes is not understood. We investigated germline polymorphisms that modulate overall survival in 1,464 surgically resected lung adenocarcinoma patients. Methods: A multivariable Cox proportional hazard model was used to assess the association of more than 7 million polymorphisms with overall survival at the 60-month follow-up, considering age, sex, pathological stage, decade of surgery and principal components as covariates. Genes in which variants were identified were studied in silico to investigate functional roles. Results: Six germline variants passed the genome-wide significance threshold. These single nucleotide polymorphisms mapped to non-coding (intronic) regions on chromosomes 2, 3, and 5. The minor alleles of rs13000315, rs151212827, and rs190923216 (chr. 2, 3 and 5, respectively) were found to be independent negative prognostic factors. All six variants have been reported to regulate the expression of nine genes, seven of which are protein-coding, in different tissues. Survival-associated variants on chromosomes 2 and 3 were already reported to regulate the expression of NT5DC2 and NAGK, with high expression associated with the minor alleles. High NT5DC2 and NAGK expression in lung adenocarcinoma tissue were already shown to correlate with poor overall survival. Conclusions: This study highlights a potential regulatory role of the identified polymorphisms in influencing outcome and suggests a mechanistic link between these variants, gene expression regulation, and lung adenocarcinoma prognosis. Validation and functional studies are warranted to elucidate the mechanisms underlying these associations.

Rasagiline (Azilect®) is a selective monoamine oxidase B (MAO-B) inhibitor that provides symp-tomatic benefit in Parkinson’s disease (PD) treatment and found to exert preclinical neuroprotec-tive effects. Here, we investigated the neuroprotective signaling pathways of rasagiline in the PC12 neuronal cultures exposed to an ischemic-like insult. Exposure of neurons to oxy-gen-glucose deprivation for 4 h followed by 18 h of reoxygenation caused 40% aponecrotic cell death. Rasagiline induced dose-dependent neuroprotection by decreasing cell death and produc-tion of the neurotoxic reactive oxygen species, and reducing the nuclear translocation of glycer-aldehyde-3-phosphate dehydrogenase (GAPDH). Rasagiline increased protein kinase B (Akt) phosphorylation and decreased protein expression of the ischemia-induced α-synuclein protein, in correlation to the neuroprotective effect. Treatment with rasagiline induced nuclear shuttling of transcription factor Nrf2 and increased the mRNA levels of the antioxidant enzymes heme oxy-genase-1, (NAD (P) H- quinone dehydrogenase, and catalase. These results indicate that rasagiline provides neuroprotection in the ischemic neuronal cultures with inhibition of α-synuclein and GAPDH-mediated aponecrotic cell death, and via mitochondrial protection, as by increasing mi-tochondria-specific antioxidant enzymes by a mechanism involving the Akt/Nrf2 redox-signaling pathway. These findings may be exploited for neuroprotective drug development in PD and stroke therapy.

The development and utilization of wind energy is of great significance to the sustainable development of China's economy and the realization of the goal of "dual carbon". Under the typhoon system, the randomness and volatility of wind speed become an important basis for affecting the energy efficiency utilization and design of wind turbines. Therefore, based on wind speed and wind direction data at 10m, 30m, 50m and 70m heights of a wind power tower in Yancheng, Jiangsu Province, this paper analyzes the change characteristics of wind speed and wind direction by using BFAST method and Hurst index. Based on typhoon body data, topographic data and mesoscale system wind direction data, the causes of the occurrence and development of wind speed and wind direction of wind tower are further analyzed, and a conclusion is drawn: (1) In BEAST method, there are 5, 5, 6 and 6 change points at the height of 10m, 30m, 50m and 70m respectively. Among them, the change points at the height of 10m, 30m and 50m all change before and after node 325, and the change time point at the height of 70m is inconsistent with other heights. Hurst index results show that the inconsistency at 70m altitude is stronger than that at other altitudes. (2) The wind direction sequence at 10m, 30m, 50m and 70m altitude is fitted by stages, and the direction of wind direction is SE-E-SE-SW-W-NW, where, At the height of 70m, the deviation of the fitting trend line from other altitudes is larger in the wind speed strengthening stage and weakening stage. (3) The wind speed at the height of 10m and 70m has different response degrees to the typhoon body. The correlation between the wind speed and the distance between the wind measurement tower and the typhoon near the center is stronger at the height of 10m than at the height of 70m. The surface type and the wind direction of the mesoscale system also have certain effects on the wind speed and direction. In this paper, the change characteristics and influencing factors of wind speed and direction of wind tower are studied, which provides methods and theoretical support for the study of short-term wind speed when typhoon passes through, and provides reliable support for the selection of wind power forecast indicators and the selection and design of wind turbines under extreme gale weather systems.

Introduction: Galectin-13 (Gal-13) is predominantly produced by the syncytiotrophoblast, while laeverin is expressed on the outgrowing extravillous trophoblast, and both are thought to be biomarkers of preeclampsia. The aim of this study was to assess the correlation between concentrations of Gal-13 and laeverin measured in maternal serum and amniotic fluid at 16-22 weeks of gestation and the sonographic assessment of the fetoplacental measurements. Materials and methods: Fetal biometric data, and placental volume and perfusion indices were measured in 62 singleton pregnancies. Serum and amniotic levels of Gal-13 and laeverin levels were measured using a sandwich ELISA. Results: Both amniotic fluid and serum Gal-13 levels expressed a negative correlation to the plasma laeverin level in mid-pregnancy. Serum laeverin level correlated positively with the gestational length at delivery (β=0.39, p

Reducing fertilizer-N rate, applying nitrification inhibitor (NI), and incorporating straw are widely recommended to improve N use efficiency of crops and decrease N losses. However, how these practices affect crop N uptake by regulating the fertilizer-N fate during the growing season is not well understood. We conducted a field 15N tracer study to explore the effectiveness of reduced N application, NI, and straw incorporation on fertilizer-N fates for maize cultivation in Northeast China. The following six treatments were used: 1) no N fertilization (control); 2) 200 kg urea-N ha−1 (100%N); 3) 200 kg urea-N ha−1 and 2400 kg dry-straw ha−1 (100%N+S); 4) 160 kg urea-N ha−1 (80%N, i.e., 20% reduction of N fertilization); 5) 160 kg urea-N ha−1 and nitrification inhibitor (Nitrapyrin) (80%N+NI); 6) 160 kg urea-N ha−1, nitrification inhibitor and 2400 kg dry-straw ha−1 (80%N+NI+S). Our results showed that the five N fertilization treatments yielded 16%–25% more grain and 39%–60% more crop N uptake than the control receiving no N fertilizer, but the differences among the five treatments were not statistically significant. In contrast to plant growth, changes in fertilizer-N fates in soil and plant pools were more pronounced. Compared with the 100%N treatment, 20% fertilizer-N reduction (80%N) decreased 15N concentration in topsoil and plant pools but increased the proportion of plant 15N recovery at harvesting (N use efficiency, NUE15N, 60% vs. 50%) (P &lt; 0.05). Nitrapyrin co-application (80%N+NI) delayed soil nitrification and increased soil 15N retention at harvesting (52% vs. 36%), thereby decreasing NUE15N significantly (P &lt; 0.05). Straw incorporation (100%N+S) decreased fertilizer-N retention compared with NI co-application because it promoted NUE15N significantly (P &lt; 0.05). The combined application of NI and straw (80%N+NI+S) was more conducive to fertilizer-N retention in soil. Our findings demonstrate that NI and straw additions are efficient strategies for stabilizing fertilizer-N in soils and potentially minimizing N loss; however, their effects on NUE15N vary and the related mechanism must be further clarified in long-term trials.

The potential of generalized machine learning models developed for crop water estimation was examined in the current study. Extreme Gradient Boosting (XGBoost), Gradient Boosting Machine (GBM), and Random Forest (RF) are three ensembled machine learning models that were developed using all of the data from a single location from 1976 to 2017 and then immediately applied at eleven different locations without the need for any local calibration. For the test period of January 2018 to June 2020, the model's capacity to estimate the numerical values of crop water requirement (Pen-man-Monteith (PM) ETo values) was assessed. In comparison to the GBM and RF models, the XGBoost model outperformed them both marginally and significantly. The estimate's weighted standard error was smaller than 0.85 mm/day, and the model's effectiveness varied from 96% to 99% across various locations. The model's strong performance was indicated by the decreased noise-to-signal ratio. A real-time water management system at the regional level can be seamlessly linked with this type of model due to its accuracy in estimating crop water requirements and its capacity to generalize.

Ultrasound, as mechanical waves with frequencies exceeding 20 thousand hertz, has found wide applications in medicine, physiotherapy, and more recently in agriculture. This study aimed to investigate the impact of ultrasound on potato yield and its parameters, particularly on seed potato yield, quantity, mass, and multiplication coefficient of potato tubers. The research was based on a three-year field experiment, utilizing the randomized block design in a split-split-plot arrangement, in the central-eastern region of Poland. The primary factor were technologies: a) technology with employing ultrasonic pre-planting treatment, b) traditional cultivation without this treatment. The secondary factors were potato varieties. Sonication of tubers was conducted using a bath-type ultrasonic device equipped with piezoe-lectric transducers. Results revealed a significant influence of cultivation technology, cultivar, and weather conditions on seed tubers yield, quantity, and multiplication coefficient of potato tubers. However, genetic traits of the examined varieties and random factors significantly affected the individual seed tuber mass and the number of shoots emerging from a single tuber. Future Outlook: Future research could focus on further optimizing ultrasound application techniques in potato cultivation, considering diverse varieties and environmental conditions. Additionally, it would be worthwhile to analyze the long-term effects of ultrasound on tuber seed potato quality and their ability to adapt to changing climatic and soil conditions. Furthermore, studies investi-gating the impact of ultrasound on other plant species could broaden our understanding of po-tential benefits in agriculture.

A pink-pigmented, ovoid-rod-shaped, gram-negative bacterial strain ML10T was isolated from a meromictic lake in British Columbia, Canada. It produces bacteriochlorophyll a, which is incorporated into the reaction center and light harvesting I complexes. This alongside no anaerobic or photoautotrophic growth supports the designation of the strain as an aerobic anoxygenic phototroph. The cells produce wavy polar flagellum and accumulate clear, refractive granules, presumed to be polyhydroxyalkanoate. Sequence of the 16S rRNA gene identified close relatedness to Salinarimonas rosea (97.85 %), Salinarimonas ramus (97.92 %) and Saliniramus fredricksonii (94.61 %). The DNA G + C content was 72.06 mol %. Differences in cellular fatty acids and some physiological tests compared to Salinarimonadaceae members, as well as average nucleotide identity and digital DNA-DNA hybridization define the strain as a new species in Salinarimonas. Therefore, we propose that ML10T (= NCIMB 15586T = DSM 118510T) be classified as the type strain of a new species in the genus with the name Salinarimonas chemoclinalis sp. nov.

One ambitious objective of Integrated Computational Materials Engineering (ICME) is to shorten the materials development cycle by using computational materials simulation techniques at different length scales. In this regard, the most important aspects are the prediction of the microstructural evolution during material processing and the understanding of the contributions of microstructural features to the mechanical response of the materials. One possible solution to such a challenge is to apply the Phase Field (PF) method because it can predict the microstructural evolution under the influence of different internal or external stimuli, including deformation. To accomplish this, it is necessary to take into account plasticity or, specifically, non-homogeneous plastic deformation, which is particularly important for investigating the size effects in materials emerging at the micron length scale. In this work, we present quasi-2D simulations of plastic deformation in a face centred cubic system in a finite strain formulation. Our model consists of dislocation-based strain gradient crystal plasticity implemented into a PF code. We apply this model to study the influence of grain size on the mechanical behavior of polycrystals, which includes dislocation storage and annihilation. Furthermore, the initial state of the material before deformation is also considered. The results show that a dislocation-based strain gradient crystal plasticity model can capture the Hall-Petch effect in many aspects. The model reproduced the correct functional dependence of the flow stress of the polycrystal on grain size without assigning any special properties to the grain boundaries. However, the predicted Hall-Petch coefficients are significantly smaller than those found typically in experiments. In any case, we found a good qualitative agreement between our findings and experimental results.

The new class of mRNA vaccines is studied extensively, leading to many novel prospects based on the pivotal success of vaccines against the SARS-Cov-2 virus. Many novel mechanisms of immune response discovered have led to the possibility of mutation-resistant vaccines by combining multiple conserved epitopes as antigens to manipulate the T-cell and B-cell responses; these antigens can also come from different organisms, providing protection against numerous diseases and of most tremendous significance is the utility of mRNA vaccines in preventing and treating more than 100 autoimmune disorders. This is a significant humanitarian breakthrough given the ease and faster and low cost of mRNA vaccines, being a chemical entity. This paper provides a prospective analysis of mRNA vaccines with much broader applications than anticipated when these vaccines entered treating SARS-Cov-2 infections.

This brief commentary challenges the use of the term "energy deficiency" in nutrition and metabolism, providing a critical examination of its scientific and philosophical aspects. It emphasizes the need to consider rare diseases associated with actual energy deficiency, which extend beyond the scope of everyday tiredness or fatigue. By analyzing energy balance and its complexities, this critique underscores the oversimplification associated with the term and its potential for misleading implications. It highlights the dynamic nature of energy metabolism and the intricate mechanisms involved in maintaining energy equilibrium, including the impact of rare genetic and physiological abnormalities. In addition to the discussion on energy balance, this commentary explores the manifestation of rare diseases that disrupt energy production, utilization, or hormonal regulation. Conditions such as mitochondrial diseases, glycogen storage diseases, adrenal insufficiency, and Prader-Willi syndrome are examined, shedding light on their profound impact on individuals' energy levels and overall health. The distinct time courses, underlying mechanisms, and clinical implications of protein deficiency, energy deficiency, and vitamin C deficiency are also compared, further emphasizing the complexity of energy metabolism and its relationship with various nutrient deficiencies. To foster a more comprehensive understanding of energy metabolism and enhance clarity in communication within the field, the commentary proposes the adoption of alternative terminology, such as "energy flux," to capture the multifaceted nature of energy balance more accurately. By reevaluating the terminology employed, researchers and healthcare professionals can better convey the intricate dynamics of energy metabolism and address the unique challenges faced by individuals with rare diseases causing actual energy deficiency. In conclusion, this commentary serves as a thought-provoking exploration of the concept of energy deficiency in nutrition and metabolism. It highlights the limitations of the term in capturing the complexities of energy balance, particularly in the context of rare diseases. By broadening the discussion to include these rare conditions, it encourages a more comprehensive understanding of energy metabolism and calls for precise and nuanced terminology to facilitate effective communication and advancements in the field.

Coupled Delft3D-object model has been developed to predict object’s mobility and burial on sandy seafloor. The Delft3D model is used to predict seabed environment such as currents, waves (peak period, significant wave height, wave direction), water level, sediment transport, and seabed change, which are taken as the forcing term to the object model consisting of three components: (a) object‘s physical parameters such as diameter, length, mass, and rolling moment, (b) dynamics of rolling cylinder around its major axis, and (c) empirical sediment scour model with re-exposure parameterization. The model is compared with the observational data collected from a field experiment from 21 April to 23 May 2013 off the coast of Panama City, Florida funded by the Department of Defense Strategic Environmental Research and Development Program. The experimental data contain both objects’ mobility using sector scanning and pencil beam sonars and simultaneous environmental time series data of the boundary layer hydrodynamics and sediment transport conditions. Comparison between modeled and observed data clearly show the model capability.

Nowadays the relationship between planning land use and actual land use is not so clear in general. A lot of efforts have been put in the failures of regulation for the expansion of construction land. However, it still lacks an integrated approach to study the effectiveness of land use regulation in terms of different land use types. Furthermore, the existing evaluation of land use plan mainly focuses on a general level, a detailed research on the regulation effectiveness of each construction land use type is absent. Therefore, this research tries to evaluate regulation effectiveness of land use plan, which takes Cangwu country, Guangxi Province as an example. The finding by analysis is that the total area of construction land expansion was about 3494.73 ha, nearly 1.1 times of the plan quota. Moreover, the effectiveness differs greatly in various construction land use types. Town, industrial/mining sites can be well regulated through the quota of land use plan. While, the quota regulation system is not as effective for other type of construction land. Thus, we suggest to improve the regulation effectiveness of construction land through different plan instruments.

Bovine respiratory disease (BRD) is the leading cause of morbidity and mortality in cattle raised in North America. At the feedlot, cattle are subject to metaphylactic treatment with macrolides to prevent BRD, a practice that may promote antimicrobial resistance and has resulted in an urgent need for novel strategies. Mannheimia haemolytica is one of the major bacterial agents of BRD. The inhibitory effects of two amphipathic, α-helical (PRW4, WRL3) and one β-sheet (WK2) antimicrobial peptides were evaluated against multidrug-resistant (MDR) M. haemolytica isolated from Alberta feedlots. WK2 was not cytotoxic against bovine turbinate (BT) cells by the MTT (3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide) assay. All three peptides inhibited M. haemolytica, with WK2, being the most efficacious against multiple isolates. At 8-16 µg/ml, WK2 was bactericidal against Mh 330 in broth and at 32 µg/ml in the presence of BT cells, reduced the population by 3 logs CFU/ml without causing cytotoxic effects. The membrane integrity of Mh 330 was examined using NPN (1-N-phenylnaphthylamine), and ONPG (o-Nitrophenyl β-D-galactopyranoside) with both the inner and outer membranes being compromised. Thus, WK2 may be a viable alternative to the use of macrolides as part of BRD prevention and treatment strategies.

Expansive soil shows dual swell-shrink which is not suitable for the construction. Several mitigating techniques exist to counteract the problem promulgate by expansive clayey soils. This paper explored the penitential mecho-chemical reinforcement of expansive clayey soil to mitigate the effect of upward swelling pressure and heave. The polypropylene fiber is randomly distributed in the soil for mechanical stabilization, and the industrial residual silica fume is used as a chemical stabilizer. The experimental analysis is made in three phases which involved the tests on mechanical reinforced expansive soil using randomly distributed polypropylene fibers with different percentages (0.25%, 0.50%, and 1.00%), and 12mm length. The second phase of experiments carried out on chemical stabilized expansive soil with different percentages (2%, 4% and 8%) of silica and next phase of the experimental focused in the combination of mecho-chemical stabilization of the expansive soil with different combination of silica (i.e., 2%, 4% and 8%) and polypropylene fibers (i.e., 0.25%, 0.50% and 1.00%). Maximum dry density (MDD), optimum moisture content (OMC), liquid limit (LL), plastic limit (PL), plastic index (PI) grain size, and constant volume swelling pressure test were performed on unreinforced and reinforced expansive soil to investigate the effect of polypropylene fiber and silica fume on the engineering properties of expansive clayey soil. The experimental results illustrate that the inclusion of polypropylene fiber has a significant effect on the upward swelling pressure and expansion property of expansive soil. The reduction in the upward swelling pressure and expansion is a function of fiber content. These results also indicated that the use of silica fume caused a reduction in upward swelling potential, and its effect was considerably more than the influence of fiber.

This study addresses the importance of conducting mass movement susceptibility mapping and hazard assessment using quantitative techniques, including machine learning, in the Northern Lima Commonwealth (NLC). Previous exploration of the topographic variables revealed high correlation and multicollinearity among some of them, which led to dimensionality reduction through principal component analysis (PCA). Six susceptibility models were generated using weights of evidence, logistic regression, multilayer perceptron, support vector machine, random forest, and naive Bayes methods to produce quantitative susceptibility maps and assess the hazard associated with two scenarios: the first being an El Niño phenomenon and the second being an earthquake exceeding 8.8Mw. The main findings indicate that machine learning models exhibit excellent predictive performance for the presence and absence of mass movement events, as all models surpassed an AUC value of &gt;0.9, with the random forest model standing out. In terms of hazard levels, in the event of an El Niño phenomenon or an earthquake exceeding 8.8Mw, approximately 40% of the NLC area would be exposed to the highest hazard levels. It also highlights the importance of integrating methodologies to reduce model uncertainty, such as comprehensive analysis of variables supported by high quality data and organized workflows. The findings of this research are expected to serve as a supportive tool for land managers in formulating effective disaster prevention and risk reduction strategies.

Vectorial optical fields have sparked considerable interest with potential applications such as optical nano-fabrication, optical micromachining, quantum information processing, optical imaging, and so on. Traditional compact vectorial optical generators with amplitude modulation perform poorly in terms of diffraction effect reduction. In order to address this issue, the refractive 4f system in amplitude modulation is longitudinally aligned using an optimization approach presented in this research. The phase images used for longitudinal alignment are loaded into the liquid crystal spatial light modulator (SLM), and the distance between the lens and the mirror in the reflective 4f system is adjusted for longitudinal alignment by compensating for the neglected phase in the integrated module of the compact vectorial optical field generator. The spot images collected by the CCD are processed using the improved eight-direction Sobel operator, and the longitudinal alignment in the reflective 4f system is determined by the sharpness of the image. The sharpness of the lines' edges and the overall image are both enhanced after optimization compared to before optimization. The results show that the proposed method can significantly reduce the longitudinal alignment error of the reflective 4f system in the amplitude modulation of the compact vectorial optical field generator, lessen the diffraction effect, and improve the performance of the system.

Iron (Fe) is co-factor for enzymes of the developing brain necessitating sufficient supply. We investigated the effects of administering ferric derisomaltose/Fe isomaltoside (FDI) subcutaneously to Fe deficient (ID) pregnant rats on cerebral and hepatic concentrations of essential metals and gene expression of ferroportin and hepcidin. Pregnant rats subjected to ID were injected with FDI on the day of mating (E0), 14 days into pregnancy (E14), or the day of birth (Postnatal (P0)). The efficacy was evaluated by determination of cerebral and hepatic Fe in pups on P0 and as adults on P70, and the concentration of copper (Cu) and zinc (Zn). Females fed an ID diet (5.2 mg/kg Fe) had offspring with significantly lower cerebral and hepatic Fe compared to female controls fed a standard diet (158 mg/kg Fe). Cerebral Cu increased irrespective of supplying a standard diet or administering FDI combined with the standard diet. Hepatic hepcidin was significantly lower following ID, whereas cerebral hepcidin was virtually undetectable in all experimental groups. In conclusion, administering FDI subcutaneously to ID pregnant rats on EO normalizes cerebral Fe in the fetus, but when applied at later gestational ages, additional Fe to the offspring is needed to normalize cerebral and hepatic Fe.

A two-year experiment was conducted with a local maize hybrid under full irrigation (F), deficit irrigation (D) and rainfed conditions (R) to estimate maize evapotranspiration in Bosnia and Herzegovina. Three approaches (Allen & Pereira (A&P), SIMDualKc (SD), and Vegetation Index (VI)) were used to estimate the actual crop coefficient (Kc act), actual basal crop coefficient (Kcb act), and actual crop evapotranspiration (ETc act) were applied with the dual crop coefficient method and remote sensing (RS) data. While Kcb act from all approaches matched FAO56 tabulated values, SD showed differences, in comparison to A&P, of up to 0.24 in D and R conditions, especially in initial and mid-season stages. VI demonstrated very good performance in all treatments. In F, the obtained Kc act for all approaches during the initial and end stages were higher than the tabulated values, ranging from 0.71-0.87 for Kc ini act and from 0.80-1.06 for Kc end act, while the mid-season period showed very good agreement with the literature. Maize crop evapotranspiration range is 769-813 mm, 480-752 mm, and 332-618 mm for F, D and R, respectively. The results confirmed the suitability of both approaches (SD and VI) to estimate maize crop evapotranspiration under F, with the VI approach demonstrating an advantage in calculating Kcb act, Kc act, and ETc act values under water stress conditions. The 67.6% increase in grain yields with irrigation emphasizes the need to transition from rainfed to irrigation-dependent agriculture, even for drought-resistant crops like maize.

Porous α-Al2O3 ceramics is a highly demanded material for multitude applications such as filters, substrates, biomedicine materials, etc. Despite the availability of the raw materials, a challenge of their technology is in a high energy budget caused by the sintering above 1500 °C. For a cold sintering processing (CSP) of ceramics, the lowering of α-Al2O3 sintering temperature is one of the most urgent challenges at the background of its rapid development. The current paper for the first time demonstrates the solution of the mentioned problem by the CSP of α-alumina ceramics in a presence of pure water as a transient liquid. The manufactured materials were examined by XRD analysis; the evolution of their microstructures during the CSP was revealed by SEM, and the porosity evaluated by the Archimedes method. The ceramics with an open porosity up to 36 % was produced at 380-450 °C, 220 MPa in 30 min. An increase in the pressure was found to impede α-Al2O3 formation from γ-AlOOH. The development of the microstructure was discussed within the frameworks of the dissolution-precipitation model and the homogenous nucleation. The results of the SEM study pointed to the coalescence of γ-AlOOH grains during the CSP.

Abstract — Game development using technology was started in 1950 around the first video game created Tennis for Two by Higginbotham as a fun diversion, to show the power of technology. The advanced development of Artificial intelligence (AI), has turned out to be the heart of game development technology and AI has revolutionized gaming and brought so many features to life.in reality, it isn't easy to give a definition and meaning to it even though games are becoming a part of human survival. It is difficult to define the real meaning of a game but it is part of human survival as it usually refers to the cleverness of the way the human being involvement in the characters of the game. As a part of game development, many technologies were used to create a game for the players with creativity, complex design, variety of levels, and aspects for the player to use choices effectively and efficiently to interact with the character in the game and enhance the experience to the next levels. This paper initially gives the importance of game development and need for the technology usage to enhance the current state of games. Then analyzes the history and present state of Artificial intelligence in game development. Finally, it explains the highlights of potential changes in game development and the impact and influence of artificial intelligence and machine learning models in the future development of games.

Background: Early diagnosis of postoperative complications is an urgent task, allowing timely prescribing of appropriate therapy and reducing the cost of patient treatment. Prognostic models based on various data could help in the early diagnosis of postoperative complications after cardiac surgery. Objectives: The purpose of the study was to determine whether an integrated approach based on clinical data along with metabolites and biomarkers had greater predictive value than the models built on less data. Methods: The study included patients (n=62) admitted for planned cardiac surgery (coronary artery bypass grafting with cardiopulmonary bypass), who were retrospectively divided into two groups depending on the presence (n=26) or absence (n=36) of postoperative complications of all types. Clinical and laboratory data on the first day after surgery were analyzed. Additionally, patients' blood samples were collected before and on the first day after surgery to determine biomarkers (interleukin-6, procalcitonin, NT-proBNP, high-sensitivity troponin T) and metabolites (8 aromatic and 2 dicarboxylic acids were detected using gas chromatography-mass spectrometry). Results: Patients before surgery, compared with healthy donors, differed in the concentration of metabolites (p &lt; 0.05), and had concentrations of a number of biomarkers exceeding the corresponding reference values. Multivariate PLS-DA models, predicting the presence or absence of postoperative complications, were built using clinical data (ROC-AUC=0.71), concentrations of metabolites and biomarkers (ROC-AUC=0.60), and the entire data set (ROC-AUC=0.75). For comparison we built univariate models using the EuroScore2 (ROC-AUC=0.59) and SOFA (ROC-AUC=0.76) scales; concentrations of lactate (ROC-AUC=0.71), the dynamic changes of 4-hydroxyphenyllactic acid (ROC-AUC=0.69), and the sum of three sepsis-associated metabolites (ROC-AUC=0.70). The proposed complex model using entire data set was comparable to the SOFA scale, which confirms the expediency of searching for new predictive models based on a variety of factors.

(1) Background: Emergencies confront civilian and military healthcare providers with medical and hygienic challenges due to the lack of potable water. This pilot study aimed to describe the application of two different methods for microbiological monitoring of water in a harsh environment in terms of performance, ease of use, availability, and the possibility of using the results to evaluate water quality. (2) Methods: Samples from raw water, Potable water, and water for consumers were taken from two different camps with the same raw water source. The samples were analyzed by using IDEXX industry-standard methods (Colilert and Enterolert enzymatic test kits) and a combination of membrane filtration and 3M-Petrifilm. (3) Results: The IDEXX method used at the Norwegian Camp are easier to utilize and has a broader range of analyzing kits for drinking water analysis. In addition, IDEXX is better adapted to the requirements of the national legislation. However, the combination of membrane filtration followed by incubation on 3M-Petrifilm ™, as used at the Swedish camp, is a better field alternative compared to traditional bacteriology, as it eliminates the need to produce and store agar plates. (4) Conclusions: This pilot study highlights the need for adapted technical equipment and tools for internal microbiological control of water production in a harsh field environment and may facilitate the use of a relatively simple method for water control and ensure the safety of deployed staff in both civilian and military settings.

Omsk hemorrhagic fever virus (OHFV) is a member of the tick-borne encephalitis virus (TBEV) complex of the Flaviviridae family. Currently, there is no data on cross-reactivity of antibodies to the NS1 proteins of OHFV and TBEV. Such data are of major interest for monitoring viral encephalitis of unknown etiology due to the increasing geographical distribution of OHFV. In this study, recombinant OHFV NS1 protein was produced using Escherichia сoli expression system and purified. The recombinant OHFV NS1 protein was recognized by specific mice immune ascetic fluids to the native OHFV NS1 protein. Western blot analysis and ELISA of recombinant NS1 proteins of OHFV and TBEV were used to study the cross-reactivity of antibodies from immune ascites fluid obtained from OHFV-infected mice and mAbs against TBEV NS1. Anti-TBEV NS1 mouse monoclonal antibodies (mAbs) have been shown not to be cross-reactive to OHFV NS1 protein. Sera from patients with confirmed tick-borne encephalitis (TBE) were examined by ELISA using recombinant OHFV NS1 and TBEV NS1 proteins as antigens. It was shown for the first time that cross-reactive antibodies to OHFV NS1 protein were not detected in the sera of TBE patients whereas the sera contained antibodies to TBEV NS1 protein.

Androgenetic alopecia is a genetic disorder caused by an excessive response to androgens. This alopecia is the most common cause of progressive hair loss in men and causes low self-esteem in patients. In this study we used various methods, including quantitative PCR, flow cytometry, ELISA, and immunocytochemistry, to evaluate the biological effects of germinated hemp seeds extract and exosomes derived from calli of germinated hemp seeds. This research reveals pre-ventive functions of two biomaterials (GE2000: 2000 ug/mL germinated hemp seeds extract; E40: 40 ng/mL exosomes derived from calli of germinated hemp seeds) for androgenetic alopecia through three biochemical categories: genetic modulation in hair follicle dermal papilla stem cells (HFDPSCs), cellular differentiation, and modulation of immune systems. Despite exposure to dihydrotestosterone (DT), two materials upregulated alopecia preventing genes including Wnt, β-catenin, and TCF in HFDPSCs. Conversely, alopecia activating genes (STAT1, 5α-reductase type 1, and IL-15R) were suppressed. Moreover, two materials suppressed alopecia genes (NKG2DL, IL2-Rβ, JAK1, and STAT1) in CD8+ T cells. Notably, E40 was effected more in-tensely in these biochemical categories than those of GE2000. Consequently, E40 and GE2000 ef-fectively prevented DT stress. Additionally, two materials activated mechanisms for hair for-mation through the biological activities of three categories.

The thymus, a central lymphoid organ in animals serves as the site for T cell development, differentiation and maturation, vital to adaptive immunity. Thymus is critical for maintaining tissue homeostasis to protect against tumors and tissue damage. Overactive or prolonged immune response can lead to oxidative stress from increased production of reactive oxygen species. Heat stress induces oxidative stress and overwhelms the natural antioxidant defense mechanisms. The study objectives were to investigate the protective properties of astaxanthin against heat-induced oxidative stress and apoptosis in the chicken thymus, by comparing the growth performance and gene signaling pathways among three groups- thermal neutral, heat stress and heat stress with astaxanthin. The thermal neutral temperature conditions were 21-22°C and heat stress temperature was 32-35°C. Both heat stress groups experienced reduced growth performance, while the astaxanthin treated group showed a slightly lesser decline. The inflammatory response and antioxidant defense system were activated by the upregulation of the NF-kB, NFE2L2, PPARα, cytoprotective capacity and apoptotic gene pathways in the heat stress compared to the thermal neutral group. Conversely, expression levels were without significance between the thermal neutral and heat stress with antioxidant groups, suggesting astaxanthin antioxidant effectiveness to mitigate inflammation and oxidative stress damage.