This paper presents the experimental campaign conducted near the Condoroma dam at 4075 m a.s.l. in an experimental setup consisting of a series of standard profile spillways with a vertical upstream face of up to five different dimensionless heights (P/Hd). The experimental results indicate that for all P/Hd ratios studied, the discharge coefficients adjusted to the Condoroma altitude are lower than those reported by classical formulations used in conventional spillway design. As a result, a generalized equation is proposed to estimate the discharge coefficient for standard spillways located in dams at similar elevations above sea level.

Vibrations of plate structures placed in a supersonic flow is considered. The undisturbed fluid flow is parallel to the plate. Two specific problems are treated: in the first one the plate is in the form of an infinite strip and the flow is in the direction of its finite length. Rigid walls extend from the sides of the plate indefinitely. In the second problem, the plate is a finite rectangle and the flow is parallel to one of its sides. The first problem is a limiting case of the second problem. The flow is modeled by piston theory which assumes that the fluid pressure on the plate is proportional to local slope. This approximation is widely used at high speeds, and reduces the interaction between the fluid flow and the vibrations of the plate to an additional term in the vibration equation. The resulting problem can be solved by assumed mode methods. In this study, the solution is also carried out by using the collocation method. The main result is the flutter velocity of the free fluid flow under which the plate vibrations become unstable. Finally, simple expressions are proposed between the various non-dimensional parameters that allows quick estimation of flutter velocity.

High-dimensional measurement error data are becoming more prevalent across various fields. Research on measurement error regression models has gained increasing attention due to the risk of drawing inaccurate conclusions if measurement errors are ignored. When the dimension p is larger than the sample size n, it is challenging to develop statistical inference methods for high-dimensional measurement error regression models due to the existence of bias, nonconvexity of objective function, high computational cost and many other difficulties. Over the past few years, some works have overcome the aforementioned difficulties and proposed several statistical inference methods. This paper mainly reviews the current development on estimation, hypothesis testing and variable screening methods for high-dimensional measurement error regression models and shows the theoretical results of these methods with some directions worthy of exploring for future research.

Abstract: The high entropy alloy (HEA) of equiatomic composition CrNiFeCoMn and with FCC 11 crystal structure was prepared by either induction melting and additive manufacturing with a se- 12 lective laser melting (SLM) process, starting from mechanically alloyed powders. Unlike induction 13 melting, the as-produced SLM alloy showed fine nitride and Cr-rich s phase precipitates. Mechan- 14 ical spectroscopy measurements were performed on specimens cold worked and/or recrystallized. 15 Young’s modulus values of (140±10) GPa and (90±10) GPa were measured at 300 K for induction 16 melted and SLM samples, respectively. The values increased to (160±10) GPa and (170±10) GPa for 17 recrystallized samples. Damping measurements as a function of temperature showed two peaks 18 which were attributed to dislocations bending and grain boundaries sliding. The peaks were super- 19 posed on a temperature increasing background.

UHPC is a cement-based composite that is used in new construction and/or renovation of existing structures to increase their service life. It is a unique composite material that may be used as an alternative to concrete in harsh conditions. Following decades of research and development, a wide range of commercial UHPC compositions are now accessible across the world to fulfill the growing number of applications and demand for high-quality construction materials. Although UHPC has significant advantages over conventional concrete, its use is limited because of rigid design restrictions and excessive pricing. As a consequence, a detailed analysis of UHPC's durability qualities is necessary to provide critical information for material testing requirements and methods, as well as to widen its practical applications. The goal of this study is to learn more about UHPC and to encourage more research and use of UHPC.

Infective endocarditis remains an illness that carries a significant burden to healthcare resources. In recent times, there has been a shift from Streptococcus sp to Staphylococcus sp as the primary organism of interest. This has significant consequences given the virulence of Staphylococcus and its propensity to form a biofilm, rendering non-surgical therapy ineffective. In addition, antibiotic resistance has affected treatment of this organism. The cohorts at most risk for Staphylococcal endocarditis are the elderly patients with multiple comorbidities. The innovation of transcatheter technologies alongside other cardiac interventions such as implantable devices have contributed to the increased risk attributable to this cohort. We examine the role of the heart team for diagnosis and treatment of this condition. In addition, we examine the determinants of virulence of Staphylococcus aureus, the interaction with hosts immunity and the discovery and emergence of a potential vaccine. We also examine the potential role of prophylactic antibiotics during dental procedures. With increasing rates of transcatheter device implantations, there is a projected increment of endocarditis especially in this high-risk group. A high index of suspicion is needed alongside early initiation of therapy and referral to the heart time to improve outcomes.

We communicate the theoretical results in the study of utilizing the quantum phenomena in optical current for quantum computation in the context of high precision voltage measurements. These results can be used around computation by quantum sampling and quantum communication as the basis for further research and physical implementations. We propose a Main Optical Setup (MOS) for such computation which allows to make a superstructure to implement specific computations and algorithms. To create MOS we used the nonlinear units (e.g., beta- barium borate crystal), arranged in series, powered with pulsed laser pump, and ended with the beam splitter to generate the output state of a number of entangled photon pairs. The computation is made by propagation of entanglement with beam splitters applied crossword and adjustable phase shifters that are tools for parameter steering. We show how to implement the series of cosine-based components on the example of two-component case. The results opens a broad area for future research in the area of building quantum optimizer using the quantum sampling methods and in the area of high precision temporal measurement of voltage, which is the important process for building high-fidelity devices.

Methods of path integrals are used to develop multi-factor probabilities of bid-ask variables for use in high-frequency trading (HFT). Adaptive Simulated Annealing (ASA) is used to fit the nonlinear forms so developed to a day of BitMEX tick data. Maxima algebraic code is used to develop the path integral codes into C codes, and sampling code is used for the fitting process. After these fits, the resultant C code is very fast and useful for forecasting upcoming ask, bid, midprice, etc., when narrow and wide windows of incoming data are used. A bonus is the availability of canonical momenta indicators (CMI) useful to forecast direction and strengths of these variables.

The expression "Follow the water" is used in order to recognize inside the universe, life as it exists on Earth. It is shown here that the expression "Follow the water in its high-subcritical state" can be used in order to recognize the components of life which form prior to the emergence of life. This specific state of water leaves signatures inside the minerals which are produced during high-subcritical water/rock interaction.

Polymer-derived SiC-polycrystalline fiber (Tyranno SA) shows excellent heat-resistance up to 2000^oC, and relatively high strength. Up to now, through our research, the relationship between the strength and residual defects of the fiber, which were formed during the production processes (degradation and sintering), has been clarified. In this paper, we addressed the relationship between the production condition and the surface roughness of the obtained SiC-polycrystalline fiber, using three different raw fibers (Elementary ratio: Si₁Al_0.01C_1.5O_0.4~0.5) and three different types of reactor (Open system, Partially-open system, and Closed system). With increase in the oxygen content in the raw fiber, the degradation during the production process easily proceeded. In this case, the degradation reactions (SiO+2C=SiC+CO and SiO₂+3C=SiC+2CO) in the inside of each filament become faster, and then the CO partial pressure on the surface of each filament is considered to be increased. In consequence, according to Le Chatelier’s principle, the surface degradation reaction and grain growth of formed SiC crystals would be considered to become slower. That is to say, using the raw fiber with higher oxygen content and closed system (highest CO content in the reactor), much smoother surface of the SiC-polycrystalline fiber could be achieved.

In this paper, a novel integrated high precision vacuum microelectronic accelerometer is put forward based on the theory of field emission, the accelerometer consists of sensitive structure and interface ASIC. The sensitive structure has a mass of a cathode cone tips array, a folded beam, an emitter electrode and a feedback electrode. The sensor is fabricated on a double side polished (1 0 0) N-type silicon wafer, the tips array of cathode are shaped by wet etching with HNA (HNO3, HF and CH3COOH) and metalized by TiW/Au thin film. The structure of sensor is released by ICP process finally. The interface ASIC was designed and fabricated based on the P-JFET high voltage bipolar process. The accelerometer is tested through static field rollover test, and the test results show the integrated vacuum microelectronic accelerometer has good performances, which sensitivity is 3.081V/g and non-linearity is 0.84% in the measuring range of −1g~1g.

This study investigates the historical variability in annual average precipitation in the northwest region of Mexico, aiming to evaluate the cumulative impact of precipitation on soil degradation and associated risks posed by rainfall. Despite being known as "The Agricultural Heart of Mexico," the region's soil has experienced significant damage to its granulometric structure due to unpredictable rainfall patterns attributed to climate change. Sixteen historical series of average annual rainfall were analyzed as stationary stochastic processes for spectral analysis. The results revealed exponential decay curves in each radial spectrum, indicating a linear relationship between frequency and amplitude. These curves identified initial impulses correlated with moments of severity for structural damages caused by rainfall-induced degradation. The degradation process, exacerbated by water stress, accelerates, as evidenced by maps illustrating approximately 75% soil damage. In the context of climate change and the uncertainty surrounding soil responses to extreme meteorological events, understanding this phenomenon becomes crucial. Recognizing the dynamic nature of soil responses to environmental stressors is essential for effective soil management. Emphasizing the need to employ numerical processes tailored to new environmental considerations related to observed soil damages is crucial for sustainable soil management practices in any region.

The article is devoted to the issues of assessing the impact of changes in the delay value in the feed direction, what determines the regenerative nature of self-excitation of the cutting system, on the dynamics of metal processing on metal-cutting machines. It is this interconnected model of the cutting system that allows to identify the main dynamic effects that occur in the cutting system, including the effect of vibrations regeneration when cutting along the track. The article also has a section dedicated to the experiment on a real metalworking machine, on which vibrations of the top of the cutting wedge of the tool were measured and based on these data, a real calculation of the delay time and the magnitude of the change in the area of the cut layer was carried out, due to variations in the real feed. The conducted studies have shown that in addition to the vibrations of the cutting tool in the direction of feeding, the vibration activity of the tool in the direction of cutting plays an essential role in ensuring the regenerative effect. The delay time constant of the operator is formed, which determines the real value of the feed during cutting.

Background: for patients with endocarditis, guidelines recommend repeating blood cultures until they become negative, but with very limited evidence. Methods: a literature review was done on the incidence and duration of persistent bacteremia and persistent fever in endocarditis patients, compared to their associations with persistent infection at day 7. Results: persistent bacteremia and persistent fever are common in the first few days after starting antibiotic therapy, a normal duration for either at or around < 3-7 days. Persistent bacteremia is more prevalent and longer lasting in Staphylococcus (especially MRSA) and Enterococcus species than in Streptococcus species. In one study the risk for persistent infection at day 7 was 50% in those with positive blood cultures at 48-72 hours while it was 32% in those with negativization of blood cultures. Both persistent bacteremia at 48-72 hours and persistent infection at day 7 are predictive of in-hospital mortality. Conclusion: persistent bacteremia after treatment for endocarditis is common and often accompanied by persistent fever. Persistent infection at 7 days (as indication for urgent surgery) cannot be reliably predicted by positive or negative blood cultures at 48-72 hours. The recommendation of performing survey blood cultures in all patients therefore needs to be reconsidered.

Multi-stakeholder participation processes in watershed management face challenges due to limited monitoring and baseline data, resulting in a lack of awareness among stakeholders about the current state of the watershed. This knowledge gap often leads to conflicts of interest, where the broader impacts of individual decisions are overlooked. To overcome these limitations, this paper explores the design and implementation of a Serious Game (SG) aimed at co-producing a watershed management plan at the basin scale within the specific context of the Campoalegre River basin in Colombia. By providing an interactive platform, the SG facilitates collaboration between local actors, who may be unfamiliar with existing watershed plans, and decision-makers. The goal is to create a participatory space where stakeholders can comprehend the watershed management plan structure and prioritize actions based on various climatic, social, and economic conditions. Following the application of the SGs, stakeholders demonstrated an improved understanding of the basin, fostering increased participation, open debate, and the proposal of actions. These outcomes serve as valuable inputs for the implementation of water management planning policies, showcasing the potential of SGs in bridging knowledge gaps, and fostering effective multi-stakeholder engagement.

Certain Trichoderma isolates provide biofertilizer, biocontrol, and other plant-beneficial activities while inhabiting the soil or internal plant issues; and their use in agricultural systems could contribute to sustainable food production. It is thought that this colonization of soil and internal plant tissues is fundamental for biocontrol and biofertilizer applications. Our collective analyses of prior surveys, where the tef1 sequence was almost exclusively used to identify Trichoderma species, showed that isolates from the Harzianum Complex Clade, the T. asperellum/T. asperelloides group, T. virens, T. hamatum, and T. atroviride were prevalent in soil and/or as endophytes. Population structure and genetic diversity of these species were investigated, and new lineages with geo-graphic significance within T. atroviride, T. asperellum, T. hamatum, and T. virens populations were found. The nearest relatives of some species were also revealed. Choosing isolates from among more than 500 known Trichoderma species for use in non-targeted evaluation screens for biocontrol or biofertilizer applications is time-consuming and expensive. Preferentially selecting species from T. atroviride, T. asperellum/T. asperelloides, T. hamatum, species from the T. harzianum Complex Clade, T. virens, and possibly nearest relatives, may speed the identification of candidates for commercialization due to the demonstrated ability of these species to successfully inhabit the soil and endorhizosphere. To our knowledge, this is the first report where dominant soil- and en-dophyte-inhabiting Trichoderma species were identified from past survey data and population structure and genetic diversity analyses conducted.

Ornamental kale (Brassica oleracea var. acephala) is an attractive ornamental plant with a range of leaf colors and shapes. Breeding new varieties of ornamental kale has proven challenging due to its lengthy breeding cycle and the limited availability of genetic markers. Microspore culture is an effective approach to generate new materials and genetic maps are a prerequisite for quantitative trait loci analysis, MAS, fine gene mapping, and genome sequence assembly. In this study, a F1DH ornamental kale population comprising 300 DH lines was constructed using microspore culture. A high-density genetic map was developed by conducting whole-genome sequencing on 150 individuals from the F1DH population. The genetic map contained 1,696 bin-markers with 982,642 single-nucleotide polymorphisms (SNPs) spanning a total distance of 775.81 cM on all nine chromosomes with an average distance between markers of 0.46 cM. The ornamental kale genetic map contained substantially more SNP markers compared with published genetic maps for other B. oleracea crops. The F1DH progenies provide an excellent resource for germplasm innovation and breeding new varieties of ornamental kale. The high-density genetic map provides crucial insights for gene mapping and unraveling the molecular mechanisms behind important agronomic traits in ornamental kale.

We aimed to determine if infection-associated urine biomarkers can differentiate true urinary tract infection (UTI) from non-UTI controls. Midstream clean-catch urine samples were collected from asymptomatic volunteers and symptomatic subjects > 60 years old diagnosed with presumptive UTI in a specialty setting. Microbial identification and density were assessed using multiplex PCR/pooled antibiotic susceptibility test (M-PCR/P-AST) and standard urine culture (SUC). Three biomarkers (NGAL, IL-8, and IL-1β) were measured in the same urine specimens. Definitive UTI cases were symptomatic and had positive microorganism detection by SUC and M-PCR, while definitive non-UTI cases were asymptomatic volunteers regardless of microbial detection. We observed a strong positive correlation (R2 ≈ 1) between microbial density and the biomarkers NGAL, IL-8, and IL-1β. Biomarker consensus criteria of two or more positive biomarkers had sensitivity 90.2%, specificity 91.2%, positive predictive value (PPV) 91.7%, negative predictive value (NPV) 89.7%, accuracy 90.7%, positive likelihood ratio of 10.28, and negative likelihood ratio of 0.11 in differentiating definitive UTI from non-UTI cases, regardless of microbial density. NGAL, IL-8, and IL-1β showed a significant elevation in symptomatic cases with positive microbe identification compared to asymptomatic cases with or without microbe identification. Biomarker consensus exhibited high accuracy in distinguishing UTI from non-UTI cases.

In this paper, a distinction is first made between environmental, sustainable and green chemistry; the last two are then examined in relation to the more general problem of the environmental education. A brief historical digression on the STS (Science, Technology and Society) movement tries to dissect the reasons why chemistry is seen by the general public as a problem, not as a decisive resource for the realization of the ecological transition. Although sustainable and green chemistry can be decisive in overcoming the insularity of chemical disciplines in the high school, it fails to effectively embed itself in educational practices. Specific operational goals, supporting a real scientifical and technological literacy in sustainable and green chemistry, can help chemical educators. They are provided at the end of an examination of the founding axes of sustainable and green chemistry, according to the criteria of scientific and technological literacy.

Roundabouts need capacity and safety improvements compatible with manual-driven, not only with autonomous vehicles. The signaling and control of roundabouts must evolve and incorporate current technologies. For that, we approach roundabouts as synchronous switches of vehicles. This paper describes Synchronous Roundabouts with Rotating Priorities, a roundabout control system based on vehicle platoons arriving at the roundabout at speed identical to the roundabout and within the time slot assigned to their entry, avoiding conflicts and stops, thus increasing roundabout capacity and safety. Signaling is visual for human drivers and also wireless for connected and autonomous vehicles. We evaluate analytically and with simulations roundabouts of different radius for several values of the average distance between vehicles. Average delays are 28,7 % lower, with negligible dispersion. The capacity improvements depend on design parameters: in our set is moderate for small roundabouts but goes up to 70-100 % for short distances and medium and large roundabouts.

In this paper, we proposed a high accurate and stable Legendre transform algorithm which can reduce the potential instability for very high order at a very small increase in the computational time. The error analysis of interpolative decomposition for Legendre transform is presented. By employing block partitioning of Legendre-Vandermonde matrix and butterfly algorithm, a new Legendre transform algorithm with computational complexity O(N(logN)^2/loglogN) in theory and less than O(N(logN)^4) in practical application is obtained. Numerical results are provided to demonstrate the efficiency and numerical stability of the new algorithm.

Traumatic nerve injuries are common lesions that affect several hundred thousand humans, as well as dogs and cats. The assessment of nerve regeneration trough animal models may provide information for translational research and future therapeutic options that can be applied mutually in veterinary and human medicine, in a one health perspective. This review offers a hands-on vision about the non-invasive and conservative approaches on peripheral nerve injury, focusing the role of neurorehabilitation in nerve repair and regeneration. The peripheral nerve injury may lead to hypersensitivity, allodynia and hyperalgesia, with the possibility of joint contractures, decreasing functionality and impairing the quality of life. The question remains regarding how to improve nerve repair with surgical possibilities, but also considering electrical stimulation modalities by modulating sensory feedback, upregulation BDNF, GFNF, TrKB and adenosine monophosphate, maintaining muscle mass and modulating fatigue. This could be improved by the positive synergetic effect of exercises and physical activity with locomotor training, and other physical modalities, such as low-level laser therapy and ultrasounds. In addition, the use of cell-based therapies is an innovative treatment tool in this field. These strategies may help avoiding situations of permanent monoplegic limbs that could lead to amputation.

Background Endometrial cancer is the fourth most common type of cancer in the world. Due to the prevalence and high morbidity, it is of key importance to make a quick and accurate diagnosis and effective therapy. The use of photodynamic therapy (PDT) in the treatment of endometrial cancer is a significant challenge in conducting clinical trials. PDT is non-invasive, with few side effects, damaging only neoplastic tissue, leaving healthy adjacent structures intact. Thanks to numerous experiments (also in vitro), PDT is gaining more and more recognition as a potential tool in endometrium cancer treatment. Objective The aim of the study was to analyze the effectiveness of photodynamic therapy on endometrial cancer tissue samples Methods In the in vitro experiment of PDT, sections of endometrial cancer tissue taken from female patients were subjected to. Rose Bengal was used as a photosensitizer in order to assess the usefulness of the applied PDT and to introduce these solutions into the in vivo test procedure. Results Changes on the cellular substrate, such as: chromatin condensation, disturbed structure and shape of cell nuclei were observed in all tissues subjected to PDT. Conclusions The PDT experiment in vitro offers opportunities and hopes for using the chosen procedure also in vivo. Keywords endometrial cancer; photodynamic therapy; in vitro; treatment; rose bengal

Nanotechnology has become a popular topic in agricultural and animal research, generating sig-nificant global interest. Nanoparticles (NPs)-enabled agriculture and animal husbandry (AHs) products have three main principles: crop production, protection, and nutrient enrichment. Re-search on this topic has grown exponentially in recent years, with an increasing number of peer-reviewed literature and patents on NPs-enabled agriculture and AH products. This study examines and collects data on the various applications of NPs-enabled agricultural products for crop production, protection, and livestock improvement from the core nanotechnological database. The search returned several types of NPs and products used in agriculture and AH, countries that utilize these products at a commercial level, and analysis of these data by phyton, R-statistical software. Our findings show remarkable growth of nanotechnology in agriculture, AH, and re-search fields for future sustainability goals in the era of climate change

Methicillin-resistant Staphylococcus aureus (MRSA) infections, in particular biofilm-organized bacteria, remain a clinical challenge and a serious health problem. Rifabutin (RFB), an antibiotic of the rifamycins class, has shown in previous work excellent anti-staphylococcal activity. Here, we proposed to load RFB in liposomes aiming to promote the accumulation of RFB at infected sites and consequently enhancing the therapeutic potency. Two clinical isolates of MRSA, MRSA-C1 and MRSA-C2, were used to test the developed formulations, as well as the positive control, vancomycin (VCM). RFB in free and liposomal forms displayed high antibacterial activity, with minimal inhibitory concentrations (MIC) ranging from 0.009-0.013 μg/mL and MBIC50 values ranging from 0.008-0.012 μg/mL, in planktonic and biofilm bacteria, respectively. Confocal microscopy studies demonstrated the rapid internalization of unloaded and RFB-loaded liposomes in the bacterial biofilm matrix. In murine models of systemic MRSA-C1 infection, Balb/c mice were treated with RFB formulations and VCM at 20 and 40 mg/kg of body weight, respectively. Obtained data proved the superior therapeutic effectiveness of RFB formulations compared to Control and VCM groups even using a two-fold lower therapeutic dose as demonstrated by significantly reduced bacterial burden and growth index values in major organs. In addition, RFB formulations were the only formulations associated with 100% survival. Globally, this study emphasizes the potential of RFB nanoformulations as an effective and safe approach against MRSA infections.

Predictive biomarkers for immune checkpoint inhibitors (ICI), such as PD-L1 expression (TPS), remain limited in clinical applications. Improved novel ICI predictive biomarkers are urgently needed. We evaluated a live single-cell functional liquid biopsy cytokine profiling platform to track immunotherapy treatment response and outcomes. Peripheral blood mononuclear cell samples of healthy donors and NSCLC patients undergoing ICI-based therapies were collected longitudinally pre-/post-treatment under IRB-approved protocols. Samples were enriched for CD4+ and CD8+ T-lymphocytes and analyzed on the IsoLight platform. The single T-cells were captured in microchambers on IsoCode chips for cytokines profiling. Functional polyfunctionality data from 55,775 single cells were analyzed using the IsoSpeak software, kappa coefficient, and Kaplan-Meier survival plots. We found a significant difference between responders and non-responders in CD8+ T-cells’ changes in overall polyfunctionality and polyfunctional strength index (ΔPSI). ΔPSI score in CD8+ T-cells performed better than PD-L1 TPS and, when combined with PD-L1 TPS, strongly correlated with early ICI treatment response with a kappa coefficient of 1.0 (p=0.003). High CD4+ T-cells ΔPSI predicted a strong trend of improved PFS (3.9-fold) and OS (3-fold). In conclusion, single peripheral T-cell polyfunctionality dynamics analysis is a promising liquid biopsy profiling platform as NSCLC ICI predictive biomarker regardless of oncogene-addiction status.

Conclusions: The quantitative method provides a large-scale overview of the biometry measurements of an entire practice. Image audits can then be focused on sonographers whose measurements are outliers, avoiding the time, complexity, and expense of auditing those whose measurements fall within the expected range. We encourage commercial software developers to include tools in their ultrasound reporting software to facilitate such quantitative review.

Aggregation of the protein α-Synuclein (αSyn) is a hallmark of Parkinson's disease (PD), dementia with Lewy bodies (DLB) and multiple systems atrophy, and alleviating the extent of αSyn pathology is an attractive strategy against neurodegeneration. The engineered binding protein β-wrapin AS69 binds monomeric αSyn. AS69 reduces primary and secondary nucleation as well as fibril elongation in vitro. It also mitigates aSyn pathology in a mouse model based on intrastriatal injection of aSyn pre-formed fibrils (PFF). Since the PFF-based model does not represent all aspects of PD, we tested here whether AS69 can reduce neurodegeneration resulting from αSyn overexpression. Human A53T-αSyn was overexpressed in the mouse Substantia nigra (SN) by using recombinant adeno-associated viral vector (rAAV). AS69 was also expressed by rAAV transduction. Behavioral tests and immunofluorescence stainings were used as outcomes.Transduction with rAAV-αSyn resulted in αSyn pathology as reported by phospho-αSyn staining and caused degeneration of dopaminergic neurons in the SN. The co-expression of rAAV-AS69 did not reduce αSyn pathology or degeneration of dopaminergic neurons. We conclude that αSyn monomer binding by rAAV-AS69 was insufficient to protect from aSyn pathology resulting from αSyn overexpression.

Huanglongbing (HLB), or citrus greening, is a devastating disease impacting citrus trees worldwide, with severe effects particularly noted in Florida. Current strategies to combat HLB have focused on aggressive replanting despite the high susceptibility of young trees to infection. In this context, it is critical to explore agronomic practices that can enhance the health and resistance of young citrus trees to HLB. Here, we demonstrate that treatment with homobrassinolide (HBr), a type of brassinosteroid, on newly planted citrus trees can delay HLB infection and improve tree health amidst the high psyllid pressure conditions endemic to Florida. Our study reveals a significant reduction in HLB infection rates in HBr-treated trees compared to control trees, with only 25% of treated trees testing positive for HLB by six months, in contrast to 100% infection in untreated trees. This delay in infection may be attributed to HBr inducing an immune response and negatively impacting psyllid performance, as subsequently demonstrated in a greenhouse experiment. Our findings suggest that HBr applications could serve as a viable strategy to enhance the resilience of citrus production against HLB, underscoring the need for further investigation into their mechanisms of action and potential role in a comprehensive pest and disease management strategy.

Background Apolipoprotein E (APOE) gene polymorphism has been implicated in the pathogenesis of various metabolic disorders, including type 2 diabetes mellitus (T2DM). Type 2 diabetes mellitus (T2DM) is a major public health concern worldwide, including in Pakistan. Cardiovascular problems linked with T2DM have a significant impact on people and society. The study's goal is to investigate the relationship between Apolipoprotein E (ApoE) genotypes, lipid profiles, and cardiovascular complications such as ischemic heart disease (IHD) and stroke. Methods: This study was carried out on 260 subjects, divided into control D1: Diabetics without cardiovascular issues. D2: Diabetics with heart disease. D3: Diabetics with stroke. D4: Diabetics with both heart disease and stroke. Anthropometric parameters (age, BMI) and risk factors (smoking, diabetes duration, hypertension) were assessed in all groups. Serum levels of TC, TG, LDL, HDL, VLDL, creatinine, BSF, and HbA1c were measured. Apolipoprotein E gene polymorphism was determined using PCR-RFLP. Results: Hypertension, BMI, and dyslipidemia, defined as elevated levels of total cholesterol, triglycerides, LDL, HDL, and VLDL, as well as uncontrolled hyperglycemia (elevated fasting blood sugar and glycated hemoglobin) in T2DM, were linked to vascular complications such as IHD and stroke. Hypertension was prevalent in 75.4% of the population, with greater rates among the elderly. Stage 2 hypertension was more prevalent in all age groups. Apolipoprotein E gene polymorphism was discovered, with genotypes 3/3, 4/4, 2/3, and 3/4 being the most prevalent. Genotype 3/4 was more common in diabetics who had IHD/stroke or both problems, whereas genotype 2/3 was linked to DM and stroke. Conclusion: It is concluded that BMI, hypertension, hyperglycemia, atherosclerosis, and dyslipidemia are linked with cardiovascular complications of type 2 diabetes. Apolipoprotein E gene polymorphism is associated with cardiovascular disease in diabetic patients by affecting the lipid profile.

Nanoporous materials, such as Metal-Organic Frameworks (MOFs), are renowned for their high selectivity as gas adsorbents due to their specific surface area, nanoporosity, and active surface chemistry. A significant challenge for their widespread application is their behavior and reduced gas uptake in wet conditions, attributed to competitive adsorption between gas and water. The current understanding of gas adsorption in wet materials is constrained by studies that utilize only small amounts of powdered porous materials (in the milligram range) within very small reactors (1-5 mL). This leaves a significant gap in knowledge about gas adsorption behaviors in larger reactors and when MOF sample sizes are increased (to the gram scale) for scaling up the process. Additionally, there is a notable dearth of experimental research in situations where MOFs are heavily saturated with water. To address these gaps, this study measures CH4 adsorption in MOFs under conditions of high moisture content, using larger samples of MOFs (in grams) and a large volume reactor. We selected commercially available MOFs, including HKUST-1, ZIF-8, MOF-303, and activated carbon. A high-pressure isotherms (at T = 274.15 K) using volumetric approach were measured to qualitatively compare the moles of gas adsorbed under both dry and wet conditions across different MOFs and weights. Experimental results show that the presence of water led to a decrease in total CH4 mmol adsorption in MOFs, with a more significant decrease observed in hydrophilic MOFs compared to hydrophobic ones. For hydrophilic MOFs, presence of crossover isotherms at crossover pressure provided evidence of water's conversion to hydrate and its positive role in enhancing total gas uptake, which varied among different hydrophilic MOFs. Oversaturated MOFs showed a larger deviation between dry and wet cases at higher pressures. The high-pressure isotherm data confirm the positive role of hydrophilic MOFs in the conversion of water to hydrate in oversaturated MOFs when MOFs sample size is large.

A phenotype is the composite of an observable expression of a genome for traits in a given environment. The trajectories of phenotypes computed from an image sequence and timing of important events in a plant’s life cycle can be viewed as temporal phenotypes and indicative of the plant’s growth pattern and vigor. In this paper, we introduce a novel method called FlowerPhenoNet which uses deep neural networks for detecting flowers from multiview image sequences for high throughput temporal plant phenotyping analysis. Following flower detection, a set of novel flower-based phenotypes are computed, e.g., the day of emergence of the first flower in a plant’s life cycle, the total number of flowers present in the plant at a given time, the highest number of flowers bloomed in the plant, growth trajectory of a flower and the blooming trajectory of a plant. To develop a new algorithm and facilitate performance evaluation based on experimental analysis, a benchmark dataset is indispensable. Thus, we introduce a benchmark dataset called FlowerPheno which comprises image sequences of three flowering plant species, e.g., sunflower, coleus, and canna, captured by a visible light camera in a high throughput plant phenotyping platform from multiple view angles. The experimental analyses on the FlowerPheno dataset demonstrate the efficacy of the FlowerPhenoNet.

Designing motion representations for the problem of 3D human action recognition from skeleton sequences is an important yet challenging task. An effective representation should be robust to noise, invariant to viewpoint changes and result in a good performance with low-computational demand. Two main challenges in this task include how to efficiently represent spatio-temporal patterns of skeletal movements and how to learn their discriminative features for classification task. This paper presents a novel skeleton-based representation and a deep learning framework for 3D action recognition using RGB-D sensors. We propose to build an action map called SPMF (Skeleton Posture-Motion Feature), which is a compact image representation built from skeleton poses and their motions. An Adaptive Histogram Equalization (AHE) algorithm is then applied on the SPMF to enhance their local patterns and form an enhanced action map, namely Enhanced-SPMF. For learning and classification tasks, we exploit Deep Convolutional Neural Networks based on the DenseNet architecture to learn directly an end-to-end mapping between input skeleton sequences and their action labels via the Enhanced-SPMFs. The proposed method is evaluated on four challenging benchmark datasets, including both individual actions, interactions, multiview and large-scale datasets. The experimental results demonstrate that the proposed method outperforms previous state-of-the-art approaches on all benchmark tasks, whilst requiring low computational time for training and inference.

In this work, we designed a MEMS device which allows simultaneous direct measurement of mechanical properties during deformation under external stress and characterization of the evolution of microstructure of nanomaterials within a transmission electron microscope. This MEMS device makes it easy to establish the correlation between microstructure and mechanical properties of nanomaterials. The device uses piezoresistive sensors to qualitatively measure the force and displacement of nanomaterials, e.g., in wire and thin plate forms. The device has a theoretical displacement resolution of 0.19 nm and a force resolution of 2.1 μN. The device has a theoretical displacement range limit of 2.74 μm and a load range limit of 27.75 mN.

Glioblastoma (GBM) is the most aggressive brain cancer. To model GBM in research, orthotopic brain tumor models, including syngeneic models like GL261 and genetically engineered mouse models like TRP, are used. In longitudinal studies, tumor growth and treatment response are typ-ically tracked with in vivo imaging, including bioluminescence imaging (BLI), which is quick, cost-effective, and easily quantifiable. However, BLI requires luciferase-tagged cells, and recent studies indicate that the luciferase gene can elicit an immune response, leading to tumor rejection and experimental variation. We sought to optimize the engraftment of two luciferase-expressing GBM models, GL261 Red-FLuc and TRP-mCherry-FLuc, showing differences in tumor take, with GL261 Red-FLuc cells requiring immunocompromised mice for 100% engraftment. Immuno-histochemistry and MRI revealed distinct tumor characteristics: GL261 Red-FLuc tumors were well-demarcated with densely packed cells, high mitotic activity, and vascularization. In con-trast, TRP-mCherry-FLuc tumors were large, invasive, and necrotic, with perivascular invasion. Quantifying tumor volume using the HALO® AI analysis platform yielded results comparable to manual measurements, providing a standardized and efficient approach for reliable high-throughput analysis of luciferase-expressing tumors. Our study highlights the importance of considering tumor engraftment when using luciferase-expressing GBM models, providing in-sights for preclinical research design.

Tinnitus is a symptom often associated with hearing loss (HL) and is in many cases more burdening to the individual than the HL itself. Many approaches have been made to explain the development and chronification of the phantom percept as well as different treatment strategies to lower the tinnitus related burden. In many studies, the variance of the HL data is high and therefore the interpretation of specific data might be difficult. With this retrospective study, we attempt to explain a part of this variance by investigating specifically the effects of non-auditory comorbidity categories on pure-tone audiometric data in a tinnitus patient collective that was homogeneous with respect to auditory comorbidities. We found age dependent as well as number of non-auditory comorbidity (e.g. diabetes mellitus) dependent differences in the mean HL of the tinnitus patients as well as differences in the peak HL frequency relative to the tinnitus frequency. The analysis of the age dependent HL within the different non-auditory comorbidities revealed specific – partially opposed – effects of endocrine, circulatory, muscle-skeletal and digestive disease categories on the hearing thresholds of tinnitus patients. Taken together we argue that in future tinnitus (and non-tinnitus) patient studies also non-auditory comorbidities should be taken into account as possible covariables that might explain the variance found in the auditory threshold development of these patients.

This study explores the effects of tempering on the precipitation behavior and impact toughness of high-nickel steel. The specimens underwent double quenching at 870°C and 770°C, followed by tempering at various temperatures. Advanced characterization techniques including optical microscopy (OM), scanning electron microscopy (SEM), and transmission electron microscopy (TEM) were used to elucidate precipitation phenomena. Additionally, electron backscatter diffraction (EBSD) was employed to assess the misorientation distribution after tempering. Charpy impact tests were performed on specimens tempered at different temperatures to evaluate their toughness. The findings reveal that with increasing tempering temperature, the fraction of low-angle grain boundaries decreases, which correlates positively with enhanced impact toughness. The impact toughness peaks at 580°C and then diminishes with further temperature increases.

Aligning supply chain and marketing functions is crucial for high-tech startups aiming to successfully launch new products in competitive markets. This qualitative research explores the strategies, challenges, benefits, and best practices associated with supply chain and marketing alignment in high-tech startups. Through a detailed analysis of case studies and semi-structured interviews with industry professionals, the study identifies key insights into how startups can effectively integrate these functions to enhance operational efficiency, market responsiveness, customer satisfaction, and risk management. The findings reveal that successful alignment requires the formation of cross-functional teams, leveraging integrated technologies like CRM and ERP systems, establishing regular inter-departmental communication, and developing joint performance metrics. These strategies foster collaboration and ensure that supply chain and marketing efforts are coordinated towards shared goals. However, startups face challenges such as differing departmental objectives, resource constraints, communication barriers, and technological limitations, which hinder effective alignment. Benefits observed from effective alignment include improved operational efficiency through streamlined processes, enhanced market responsiveness to adapt quickly to changing demands, increased customer satisfaction by delivering products that meet market expectations, and better risk management through proactive identification and mitigation of supply chain and market risks. Best practices identified include fostering a culture of collaboration, investing in technology for data integration and transparency, aligning strategic objectives across functions, and continuously monitoring and adjusting alignment strategies. Integration of broader elements such as sustainability, entrepreneurship, emotional intelligence, marketing, and supplier relationship management further enriches the alignment framework. This study contributes to a deeper understanding of how high-tech startups can strategically align their supply chain and marketing functions to achieve competitive advantage and sustainable growth in dynamic market environments.

Currently, foam mixers are predominantly categorized into two types: low-pressure and high-pressure. Low-pressure mixers primarily use agitator rotation to mix materials. However, they face challenges such as difficulty in cleaning and complex structures. High-pressure mixers, widely adopted for their structural simplicity and lack of need for cleaning devices, effectively mitigate issues associated with low-pressure mixers. Nonetheless, they encounter problems with uneven mixing when processing high-viscosity materials. Historically, the primary solution to this issue was increasing the working pressure. However, the capacity to increase pressure is finite, and higher pressure demands higher quality materials for the mixers. To address the issues high-pressure mixers face when dealing with high-viscosity materials, this study focuses on the polyimide high-pressure mixer. After reviewing previous studies, four design variables were selected: the mixer's impingement angle, inlet diameter, outlet diameter, and impingement pressure. Using a Full Factorial Design of Experiments (DOE), the significance of the impact exerted by these four variables on Mixing Unevenness was analyzed, determining the extent of their influence. Optimal Latin Hypercube Sampling generated several random sample points, followed by the establishment of both a Back Propagation (BP) Neural Network approximation model and a Kriging approximation model. A Genetic Algorithm was then applied to optimize these two approximation models, resulting in the optimal combination of design variables. The research findings indicate that the BP Neural Network exhibits higher predictive accuracy compared to the Kriging prediction model. The optimal combination of parameters, optimized through the Genetic Algorithm (GA), reduced the Mixing Unevenness by 69.1%, effectively decreasing the Mixing Unevenness of the mixer head.

In the digital era, enhancing the heritage resources of a tourist route means describing and networking them to promote their visibility and attractiveness. Prior studies mainly assess mountainous region’s natural resources through multi-indicator descriptive evaluation. This study aims to develop a comprehensive measurement of indicator’s value while assessing the tourism development potential of mountainous rural area. It concerns the main tourist route of the UNESCO M'Goun Geopark, located in the central High Atlas of Morocco. It also involves analyzing the criteria for choosing this destination by segmenting tourists' consumption experiences. Statistical analysis of the collected data reveals five dimensions of destination choice and four visitor groups. This article proposes to discuss findings and their applicability in terms of tourism destination management and decision-making, which can help local governments to rationally allocate tourism resources and land use.

The efficiencies of conventional triple organic Rankine cycle (TORC) configurations are restricted by the low critical temperatures of common working fluids (＜320 °C). This paper proposes a high-temperature TORC system. A near-azeotropic mixture biphenyl/diphenyl oxide (BDO), which has stellar track record in the high-temperature ORC applications, is innovatively adopted as the top and middle ORC fluid simultaneously. The top cycle evaporation temperature is up to 400 °C in view of BDO’s high stability. Five conventional organic fluids are chosen for the bottom ORC. Fundamentals of the TORC system are illustrated, and mathematical models are built. Thermo-economic performance is investigated. The results hint that the optimal thermodynamic property is achieved on the use of benzene as the bottom fluid. The maximum thermal and exergy efficiencies are respectively 40.86% and 74.14%. The largest irreversible loss occurs inside the heat exchanger coupling the middle and bottom ORCs, accounting for above 30% of the total entropy generation. The levelized energy cost (LEC) is 0.0284 $/kWh. Given the same heat source condition, the TORC system can boost efficiency by 1.02% and drive down LEC by 0.0024 $/kWh compared with a BDO mixture-based cascade ORC.

TiC particles were prepared from Ti and C powders, and TiC-reinforced Cu-based composites were prepared by powder metallurgy with SPS sintering. The effects of SPS sintering temperature and TiC particle reinforcement phase content on the electrical and mechanical properties of Cu-based composites were investigated. The reinforcement of TiC particles by thermal mismatching at increasing sintering temperature has a significant strengthening effect on the composites, but the high temperature causes softening of the Cu matrix and the growth of grains reduces the properties of the composites. In this study, the effects of porosity and density on the composite properties were not significant.

Background: Tetanus is an acute, fatal disease caused by exotoxins released from Clostridium tetani during infections. A protective humoral immune response can be induced by vaccinations with pediatric and booster combinatorial vaccines that contain inactivated tetanus neurotoxin (TeNT) as a major antigen. Although some epitopes in NeNT have been described using various ap-proaches, a comprehensive list of its antigenic determinants that are involved with immunity have not been elucidated. To that end, a high resolution analysis of the linear B-cell epitopes in NeNT was performed using antibodies generated in vaccinated children. Methods: Two hundred sixty-four peptides that cover the entire coding sequence of TeNT protein were prepared in situ on a cellulose membrane by SPOT synthesis and probed with sera from children vaccinated (ChVS) with a triple DTP-vaccine to map continuous B-cell epitopes that were further characterized and validated by immunoassays. Results: Forty-three IgG epitopes were identified. Four (TT-215-218) were chemically synthesized as Multiple Antigen Peptides (MAPs) and used in peptide ELISAs to screen post-pandemic DTP vaccinations. The assay displayed a high performance with high sensitivity (99.99%) and specificity (100%). Conclusions: The complete map of linear IgG epitopes induced by vaccination with inactivated TeNT highlights three key epitopes involved in the ef-ficacy of the vaccine. Antibodies against epitope TT-8/G can block enzymatic activity, and those against epitopes TT-40/G and TT-42/G can interfere with TeNT binding to neuronal cell receptors. We further show that four of the epitopes identified can be employed in peptide ELISAs to assess vaccine coverage. Overall, the data suggest a set of select epitopes to engineer new, directed vaccines

Laser irradiation of metals is widely used in research and applications. In this work, we study how the material geometry affects electron-phonon coupling in nano-sized gold samples: an ultrathin layer, nano-rod, and two types of gold nanoparticles: cubic and octahedral. We use the combined tight-binding molecular dynamics Boltzmann collision integral method implemented within XTANT-3 code to evaluate the coupling parameter in irradiation targets at high electronic temperatures (up to Te~20,000 K). Our results show that the electron-phonon coupling in all objects with the same fcc atomic structure (bulk, layer, rod, cubic and octahedral nanoparticles) is nearly identical at electronic temperatures above Te~7000 K, independently of geometry and dimensionality. At low electronic temperatures, reducing dimensionality reduces the coupling parameter. Additionally, nano-objects under ultrafast energy deposition experience nonthermal damage due to expansion caused by electronic pressure, in contrast to bulk metal. Nano-object ultrafast expansion leads to ablation/emission of atoms, and disorder inside of the remaining parts. These nonthermal atomic expansion and melting are significantly faster than electron-phonon coupling, forming a dominant effect in nano-sized gold.

Spent batteries recycling is an important way to obtain low-cost graphite. Nevertheless, the obtaining of crystalline graphite with a rather low density of defects is required for many applications. In the present work, high-quality graphites have been obtained from different kinds of spent batteries. Black masses from spent alkaline batteries (batteries black masses, BBM), and lithium-ion batteries from smartphones (smartphone black masses, SBM) and electric and/or hybrid vehicles (lithium-ion black masses, LBM) were used as starting materials. A hydrometallurgical process was then used to obtain recycled graphites by acidic leaching. Different leaching conditions were used depending on the type of the initial black mass. The final solids were characterized by a wide set of complementary techniques.

In this study, we propose a solution process for realizing color glass for building integrated pho-tovoltaic (BIPV) systems by spin coating a color solution composed of a pearlescent pigment mixed in a norland optical adhesive (NOA) matrix. Color solutions are made from mixing pearlescent pigments in NOA63. Compared to a physical vapor deposition process, color coatings are achieved by spin coating in a relatively simple and inexpensive process at room temperature. The optical properties can be easily controlled by adjusting the spin coating speed and the concentra-tion of the pearlescent pigments. The produced color glasses achieved a high transmittance of 85% or more in the visible wavelength range, except the wavelength spectrum exhibiting the maxi-mum reflectance. In addition, we propose a one-step lamination process of color glass on a solar cell by leveraging on the adhesive property of the NOA matrix. This eliminates the cost and pro-cess of additional ethylene vinyl acetate (EVA) layer or other materials used in the conventional lamination process. The color glass produced through this study has stability that does not change its properties over time. Therefore, it is expected to be applied to the BIPV solar module market where aesthetics and energy efficiency are required.

Intratumoral heterogeneity associates with more aggressive disease progression and worse patient outcomes. Understanding the reasons enabling the emergence of such heterogeneity remains incomplete, which restricts our ability to manage it from a therapeutic perspective. Technological advancements such as high-throughput molecular imaging, single-cell omics and spatial transcriptomics now allow recording the patterns of spatiotemporal heterogeneity in a longitudinal manner, thus offering insights into the multi-scale dynamics of its evolution. Here, we review latest technological trends and biological insights from molecular diagnostics as well as spatial transcriptomics, both of which have witnessed a burgeoning growth in recent past in terms of mapping heterogeneity within tumor cell types as well as stromal constitution. We also discuss ongoing challenges, indicating possible ways to integrate insights across these methods to have a systems-level spatiotemporal map of heterogeneity in each tumor, and a more systematic investigation of implications of heterogeneity for the patient outcomes.

By means of X-ray computed microtomography (XCMT) the existence of a developed microporous structure having an average pore diameter of ~3.5 μm and pore content of ~1.1 vol.% has been revealed in unirradiated polytetrafluoroethylene (PTFE). It has been found that the combined action of gamma radiation (absorbed dose per PTFE of ~170 kGy) and high temperatures (327-350 °C) leads to the disappearance of the microporous structure and the formation of several large pores with sizes from 30 to 50 μm in the bulk of thermal-radiation modified PTFE (TRM-PTFE). It has been established by X-ray diffraction (XRD) analysis that the thermal-radiation modification of PTFE leads to an increase in the interplanar spacings, the degree of crystallinity and volume of the unit cell, as well as to a decrease in the size of crystals and the X-ray density of the crystalline phase in comparison with the initial polymer. It is assumed that the previously established effect of improving the deformation-strength and tribological properties of the TRM-PTFE can be due not only to the radiation cross-linking of polymer chains but also to the disappearance of the micropore system and to the ordering of the crystalline phase of PTFE.

The dilatometer curves of continuous cooling transformation of 12Mn steel were measured with Formastor-FⅡthermal mechanical simulator．The steel's undercooled austenite phase continuous cooling transformation curves ( CCT curves) were established by means of the dilatometer method and the metallographic-hardness measurement method． The effect of cooling rate on microstructure and hardness of the steel was studied． CCT curve of test steel was simulated by JMatPro. The results show that the Ac1 and Ac3 of the experimental steel are 692 ℃ and 855 ℃ ; the microstructure obtained is made of ferrite，pearlite and bainite．The ferrite transformation and pearlite transformation occur at a slower cooling rate，in which the ferrite is dominant. When the cooling rate is greater than 4.25 ℃ / s bainite transformation happens．As the cooling rate increases，microstructure or grains become finer．The hardness of the tested steel with increasing cooling rate shows a trend of first fast increase and soon decrease．The simulation results are consistent with the measured CCT law. The high temperature mechanical properties of 12mn steel round billet were tested by gleeble-1500d thermal / mechanical simulator. The tensile strength, reduction of area and stress-strain curves of the billet were obtained in the range of 600-1300 ℃.

The testing of high-dimensional normality has been an important issue and has been intensively studied in literatures, it depends on the Variance-Covariance matrix of the sample, numerous methods have been proposed to reduce the complex of the Variance-Covariance matrix. The principle component analysis(PCA) was widely used since it can project the high-dimensional data into lower dimensional orthogonal space, and the normality of the reduced data can be evaluated by Jarque-Bera(JB) statistic on each principle direction. We propose two combined statistics, the summation and the maximum of one-way JB statistics, upon the independency of each principle direction, to test the multivariate normality of data in high dimensions. The performance of the proposed methods is illustrated by the empirical power of the simulated data of normal data and non-normal data. Two real examples show the validity of our proposed methods.

Background: Poor menstrual health literacy impacts adolescents’ quality of life and health outcomes across the world. The aim of this systematic review was to identify concerns about menstrual health literacy in low/middle (LMIC) and high-income (HIC) countries. Methods: Relevant social science and medical databases were searched for peer-reviewed papers from January 2008 to January 2020 identifying 61 relevant studies. Results: A thematic analysis of the data revealed that LMICs report detrimental impacts on adolescents in relation to menstrual hygiene and cultural issues, while in HICs, issues related to pain management and long term health outcomes were reported more frequently. Conclusions: In order to improve overall menstrual health literacy in LMICs and HICs, appropriate policies need to be developed, drawing on input from multiple stakeholders to ensure evidence-based and cost-effective practical interventions.

The use of different sources to energize a load is convenient in many applications, particularly those where two or more renewable energy sources are employed as: energy harvesting, hybrid vehicles, and off-grid systems. In these cases, a multi-input converter able to admit sources with different characteristics and, if necessary, select the output power of each source. Several topologies of multi-input converters have been proposed to this aim, however, most of them are based on multi-stage designs, which decreases efficiency and increases control complexity, particularly when more than two sources are used. In this work, a three-input step-up converter easy to control in open loop condition is analyzed. A designed procedure is described, and experimental results are presented for a 1 kW power converter. The implemented converter results in a higher voltage gain, less storage element keeping high efficiency compared to similar topologies. Using the procedure here proposed, this converter that was initially proposed for photovoltaic applications is enabled to be used in medium and high-power applications, for example when renewable energy sources are used.

In this work we have critically reviewed the processes in high-temperature sublimation growth of graphene in Ar atmosphere using enclosed graphite crucible. Special focus is put on buffer layer formation and free charge carrier properties of monolayer graphene and quasi-freestanding monolayer garphene on 4H-SiC. We show that by introducing Ar at different temperatures, TAr one can shift to higher temperatures the formation of the buffer layer for both n-type and semi-insulating substrates. A scenario explaining the observed suppresed formation of buffer layer at higher TAr is proposed and discussed. Increased TAr is also shown to reduce the sp3 hybridization content and defect densities in the buffer layer on n-type conductive substrates. Growth on semi-insulating substrates results in ordered buffer layer with significantly improved structural properties, for which TAr plays only a minor role. The free charge density and mobility parameters of monolayer graphene and quasi-freestanding monolayer graphene with different TAr and different environmental treatment conditions are determined by contactless terahertz optical Hall effect. An efficient annealing of donors on and near the SiC surface takes place in intrinsic monolayer graphene grown at 2000∘C, and which is found to be independent of TAr. Higher TAr leads to higher free charge carrier mobility parameters in both intrinsically n-type and ambient p-type doped monolayer graphene. TAr is also found to have a profound effect on the free hole parameters of quasi-freestanding monolayer graphene. These findings are discussed in view of interface and buffer layer properties in order to construct a comprehensive picture of high-temperature sublimation growth and provide guidance for growth parameters optimization depending on the targeted graphene application.

The CoDRIVE solution builds on R&amp;D in the development of connected and autonomous vehicles (CAVs). The mainstay of the system is a low-cost GNSS receiver integrated with a MEMS grade IMU powered with CoDRIVE algorithms and high precision data processing software. The solution integrates RFID (radio-frequency identification) localisation information derived from tags installed in the roads around the University of Nottingham. This aids the positioning solution by correcting the long-term drift of inertial navigation technology in the absence of GNSS. The solution is informed of obscuration of GNSS through city models of skyview and elevation masks derived from 360-degree photography. The results show that predictive intelligence of the denial of GNSS and RFID aiding realises significant benefits compared to the inertial only solution. According to the validation, inertial only solutions drift over time, with an overall RMS accuracy over a 300 metres section of GNSS outage of 10 to 20 metres. After deploying the RFID tags on the road, experiments show that the RFID aided algorithm is able to constrain the maximum error to within 3.76 metres, and with 93.9% of points constrained to 2 metres accuracy overall.

TiC–high Mn steel-bonded carbide with a cellular structure was designed and fabricated by powder metallurgy techniques using coarse and fine TiC particles as the hard phase. This preparation process was carefully investigated and optimized. The microstructure of the TiC steel-bonded carbide was observed using a scanning electron microscope. Results showed that there are two types of microstructures in the TiC steel-bonded carbide: the coarse-grained TiC and fine-grained TiC. The transverse rupture strength and impact toughness of the alloy reach maximum values 2231 MPa and 12.87 J/cm2, respectively when the starting weight ratio of MP-A (containing coarse TiC particles) to MP-B (containing fine TiC particles) is 60:40. Hence, this study serves as a feasible example of how to prepare a high-strength and high-toughness TiC–high Mn steel-bonded carbide.

State-of-the-art dielectrophoretic (DEP) separation techniques provide unique properties to separate particles from a liquid or particles with different properties such as material, morphology or size from each other. However, such separators do not operate at throughput that is sufficient for a vast fraction of separation tasks. The reason for this limitation is that, in order to move particles by dielectrophoresis, high electric field gradients to drive the separation are required. Conventionally, those gradients are generated by electrode microstructures that limit the maximum channel size. Here, we investigate DEP filtration, a technique that uses open porous microstructures instead of microfluidic devices to easily increase the filter cross section and therefore also the processable throughput by several orders of magnitude. Previously, we already separated baker’s yeast by DEP filtration in open porous ceramic structures. Now, we give a more elaborate experimental study about DEP filtration in these open porous structures and separate model particles, that are an order of magnitude smaller (500 nm, polystyrene), from aqueous suspensions. Almost 100% separation at flow rates of up to 9 mL min^-1 was achieved while the majority of the trapped particles could be recovered. We show how particle separation depends on key parameters (voltage, throughput, filter structure size). Further, we work towards selective particle separation and show that particle separation is very dependent on the particle polarizability: This creates the possibility to adjust selectivity by changing the electrical conductivity of the suspension around that of the particle. This study highlights the unique qualities of dielectrophoretic filtration enabling switchable, selective, and scalable particle separation to solve existing problems such as cell separation or precious metal recovery.

Background: Multifunctional nanoparticles are known for their wide range of biomedical applications. Controlling the magnetic properties of these nanoparticles is imperative for various applications, including therapeutic angiogenesis. The study was performed to evaluate the magnetic properties and their control mechanisms by the external magnetic field. Methods: A 100nm magnetic nanoparticle was placed in the magnetic field, and parametrically the magnet field strength and distance was evaluated. Various models of magnetic strength and disposition were evaluated. Magnetic flux density, force/weight, and magnetic gradient strength were the parameters evaluated in electromagnetic computational software. Results: The seven-coil method with three centrally placed coils as Halbach array, and each coil with a flux density of 7 Tesla, and with a coil dimension of 20cmx20cm (square model) of each coil showed a good magnetic strength and force/weight parameters in a distance of 15cm from the centrally placed coil. The particles were then evaluated for their motion characteristics in saline. It showed good displacement and acceleration properties. After that, the particles were theoretically assessed in a similar mathematical model after parametrically correcting the drag force. After application of high drag forces, the particles showed adequate motion characteristics. When the particle size was reduced further, the motion characteristics were preserved even with high drag forces. Conclusion: There is potential for a novel method of controlling multifunctional magnetic nanoparticles using high magnetic fields. Further studies are required to evaluate the motion characteristics of these particles in-vivo and invitro.

A novel high-voltage powerline inspection system is investigated, which consists of the cooperated ground vehicle and drone. The ground vehicle acts as a mobile platform that can launch and recycle the drone, while the drone can fly over the powerline for inspection within limited endurance. This inspection system enables the drone to inspect powerline networks in a very large area. Both vehicle’ route in the road network and drone’s routes along the powerline network have to be optimized for improving the inspection efficiency, which generates a new two-layer point-arc routing problem. Two constructive heuristics are designed based on “Cluster First, Rank Second” and “Rank First, Split Second”. Then local search strategies are developed to further improve the quality of the solution. To test the performance of the proposed algorithms, practical cases with different-scale are designed based on the road network and powerline network of Ji’an, China. Sensitivity analysis on the parameters related with the drone’s inspection speed and battery capacity is conducted. Computational results indicate that technical improvement on the inspection sensor is more important for the cooperated ground vehicle and drone system.

Iron Doped TiO₂ nanoparticles (Fe-TiO₂) were synthesized and photocatalitically investigated under high and low fluence values of UV-radiation. The Fe-TiO₂ physical characterization was performed using X-ray Powder Diffraction (XRD), Brunauer-Emmett-Teller (BET) surface area analysis, Transmission Electron Microscope (TEM), Scanning Electron Microscope (SEM), Diffuse Reflectance Spectroscopy (DRS), and X-Ray Photoelectron Spectroscopy (XPS) technique. The XPS evidenced that ferric ion (Fe³⁺) was in the lattice of TiO₂ and co-dopants no intentionally added were also present due to the precursors of the synthetic method. The Fe³⁺ concentration played a key role in the photocatalytic generation of hydroxyl radical (•OH) and estriol (E3) degradation. Fe-TiO₂ materials accomplished E3 degradation, and it was found that the catalyst with 0.3 at. % content of Fe (0.3 Fe-TiO₂) enhanced the photocatalytic activity under low UV-irradiation compared with no intentionally Fe-added TiO₂ (zero-iron TiO₂) and Aeroxide^® TiO₂ P25. Furthermore, the enhanced photocatalytic activity of 0.3 Fe-TiO₂ under low UV-irradiation may have applications when radiation intensity must be controlled, as in medical applications, or when strong UV absorbing species are present in water.

It is widely believed that the dramatic transformation of the spherical outflows of AGB stars into the extreme aspherical geometries seen during the planetary nebula (PN) phase is linked to binarity and driven by the associated production of fast jets and central disks/torii. The key to understanding the engines that produce these jets and the jet-shaping mechanisms lies in the study of objects in transition between the AGB and PN phases. I discuss the results of our recent studies with high-angular-resolution (with ALMA & HST) and at high-energies (with GALEX, XMM-Newton & Chandra) of several such objects, which reveal new details of close binary interactions and high-speed outflows. These include two PPNe (the Boomerang Nebula and IRAS16342-3814), and the late carbon star, V Hya. The Boomerang is notable for a massive, high-speed outflow that has cooled below the microwave background temperature, making it the coldest object in the Universe. IRAS16342 is the prime example of the class of water-fountain PPNe (very young PPNe with high-velocity H₂O masers) and shows the signature of a precessing jet. V Hya ejects high-speed bullets every 8.5 years associated with the periastron passage of a companion in an eccentric orbit. I discuss our work on AGB stars with strongly-variable high-energy (FUV, X-ray) emission, suggesting that these objects are in the early stages of binary interactions that result in the formation of accretion disks and jets.

The article reveals distinctive features of the interaction between architectural and structural solutions for the design of tall buildings as well as spotlights the most distinctive cases of expression. In the contemporary world, interaction is turning into the antithesis of the formerly dominant utilitarian attitude and standardization of tall buildings architectural solutions. Meanwhile, the search for rational structural solutions leads to new possibilities of architectural expression. This necessitates the transformation of a structural solution and its adaptation to the need of a modern architect to be exceptional and noticed. Interaction covers the current as well as retrospective and perspective periods. SWOT analysis was used by the authors of the article to assess the interaction between architectural and structural solutions in tall buildings design, select the most important criteria that could be used searching for rational architectural and structural solutions in future by applying multi-criteria decision making methods.

Most of existing fuzzy forecasting models partition historical training time series into fuzzy time series and build fuzzy-trend logical relationship groups to generate forecasting rules. The determination process of intervals is complex and uncertainty. In this paper, we present a novel fuzzy forecasting model based on high-order fuzzy-fluctuation trends and the fuzzy-fluctuation logical relationships of the training time series. Firstly, we compare each data with the data of its previous day in historical training time series to generate a new fluctuation trend time series(FTTS). Then, fuzzify the FTTS into fuzzy-fluctuation time series(FFTS) according to the up, equal or down range and orientation of the fluctuations. Since the relationship between historical FFTS and the fluctuation trend of future is nonlinear, Particle Swarm Optimization (PSO) algorithm is employed to estimate the required parameters. Finally, use the acquired parameters to forecast the future fluctuations. In order to compare the performance of the proposed model with that of the other models, we apply the proposed method to forecast the Taiwan Stock Exchange Capitalization Weighted Stock Index (TAIEX) time series datasets. The experimental results and the comparison results show that the proposed method can be successfully applied in stock market forecasting or such kinds of time series. We also apply the proposed method to forecast Shanghai Stock Exchange Composite Index (SHSECI) to verify its effectiveness and universality.

Linear mixed models are frequently used for analysing heterogeneous data in a broad range of applications. The restricted maximum likelihood method is often preferred to estimate co-variance parameters in such models due to its unbiased estimation of the underlying variance parameters. The restricted log-likelihood function involves log determinants of a complicated co-variance matrix. An efficient statistical estimate of the underlying model parameters and quantifying the accuracy of the estimation requires the first derivatives and the second derivatives of the restricted log-likelihood function, i.e., the observed information. Standard approaches to compute the observed information and its expectation, the Fisher information, is computationally prohibitive for linear mixed models with thousands random and fixed effects. Customized algorithms are of highly demand to keep mixed models analysis scalable for increasing high-throughput heterogeneous data sets. In this paper, we explore how to leverage an averaged information splitting technique and dedicate matrix transform to significantly reduce computations and to accelerate computing. Together with a fill-in reducing multi-frontal sparse direct solver, the averaged information splitting approach improves the performance of the computation process.

High average power narrow-linewidth tunable solid-state lasers in the wavelength region between 2 to 3 μm are attractive light sources for many applications. This paper reports a narrow-linewidth widely-tunable laser system based on the polycrystalline Cr2+:ZnSe elements pumped by the repetitively-pulsed 2.1 µm Ho3+:YAG laser operating at the tens of kilohertz pulse rate. An advanced procedure of ZnSe-element doping and surface improvement was applied to increase the laser-induced damage threshold, which resulted in an increase of the output power of the Cr2+:ZnSe laser system. The high-average-power laser system comprised double master-oscillators and power amplifiers: Ho3+:YAG and Cr2+:ZnSe laser oscillators, and Ho3+:YAG and Cr2+:ZnSe power amplifiers. The output wavelength was widely tuned within 2.3-2.7 µm by an acousto-optical tunable filter inside the Cr2+:ZnSe master oscillator cavity. The narrow-linewidth operation at the pulse repetition rate of 20-40 kHz in a high-quality beam with the average output power up to 9.7 W was demonstrated.

Estimating ground surface PM2.5 with fine spatiotemporal resolution is a critical technique for exposure assessments in epidemiological studies of its health risks. Previous studies have utilized monitoring, satellite remote sensing or air quality modeling data to evaluate the spatiotemporal variations of PM2.5 concentrations, but such studies rarely combined these data simultaneously. We develop a three-stage model to fuse PM2.5 monitoring data, satellite-derived aerosol optical depth (AOD) and community multi-scale air quality (CMAQ) simulations together and apply it to estimate daily PM2.5 at a spatial resolution of 0.1˚ over China. Performance of the three-stage model is evaluated using a cross-validation (CV) method step by step. CV results show that the finally fused estimator of PM2.5 is in good agreement with the observational data (RMSE = 23.00 μg/m^3 and R2 = 0.72) and outperforms either AOD-retrieved PM2.5 (R2 = 0.62) or CMAQ simulations (R2 = 0.51). According to step-specific CVs, in data fusion, AOD-retrieved PM2.5 plays a key role to reduce mean bias, whereas CMAQ provides all-spacetime-covered predictions, which avoids sampling bias caused by non-random incompleteness in satellite-derived AOD. Our fused products are more capable than either CMAQ simulations or AOD-based estimates in characterizing the polluting procedure during haze episodes and thus can support both chronic and acute exposure assessments of ambient PM2.5. Based on the products, averaged concentration of annual exposure to PM2.5 was 55.75 μg/m3, while averaged count of polluted days (PM2.5 > 75 μg/m3) was 81, across China during 2014. Fused estimates will be publicly available for future health-related studies.

The porosity of freshwater and sea ice is one of the main parameters that determine its strength. The strength of ice varies over a wide range of values, and the differ-ences in the intensity of the mechanisms of ice porosity formation in different water areas can be one of the possible reasons for these variations. The water mass contains gases in two forms: gases dissolved in the water mass, as well as gas bubbles that are formed when wind waves break up, and bubbles that float up from the seabed. The article presents the results of the analysis of the role of each of these forms in the formation of gas inclusions (pores) into the crystal structure of ice. The estimates showed that the main source of gas pores in ice crystals is the gas bubbles coming to the surface from the bottom, formed during the decomposition of bottom sediments or during gas leaks from near-bottom oil and gas fields. The possibility of gas bubbles occurring and rising to the ice-water boundary depends on the presence of bottom sources of the gases, the intensity of dissolution of the bubbles and the depth of the water area. Therefore, the variation in the porosity and the strength of ice over the space of the water areas can be associated with the changes in their depths, and the presence and location of the natural gas sources.

Type II diabetes (T2D) is a multifaceted metabolic disease influenced by various factors (genetic, epigenetic, environmental, and other). An alarming surge in T2D prevalence is estimated, reaching 700 million cases by 2045 worldwide. This review explores the complex interactions of multiple risk factors throughout life and offers a new perspective on T2D. Genetic and epigenetic influences are described in detail. Prenatal factors, such as exposure to undernutrition and maternal overfeeding, induce lasting epigenetic changes, affecting T2D susceptibility. Furthermore, birthweight is a crude proxy for perinatal programming, with low and high birthweights associated with increased T2D risk. Often overlooked, the early postnatal period also significantly contributes to perinatal programming. Neonatal over-nutrition and feeding choices exert lasting effects on DNA methylation and metabolic outcomes later in life. Stress during this period further exacerbates T2D susceptibility. In continuation, childhood behaviors which are influenced by prior periods contribute substantially to T2D risk. Adverse childhood experiences amplify the risk of many diseases, including T2D. Sleep hygiene throughout life plays a role in metabolic health, influencing insulin resistance and appetite regulation. In adulthood, obesity remains a prominent predictor of T2D, with chronic stress contributing to weight gain and unhealthy lifestyle. This review proposes a novel perspective, considering T2D pathophysiology as a nonlinear process governed by numerous factors and their interactions throughout life. The inherent unpredictability suggests a need for personalized interventions tailored to specific risk profiles, emphasizing the importance of understanding gene-environment interactions and embracing a holistic view of T2D pathogenesis.

Background/Objectives: Patients with rheumatoid arthritis (RA) have an increased risk of infections. The risk of presenting herpes zoster (HZ) is 1.5-2 times higher than in immunocompetent individuals and disseminated presentation is more frequent. Our aim was to analyze the prevalence and general features of HZ in RA patients. Methods: Prospective study of 392 RA patients included in the vaccination program of our hospital between 2011 and 2016, and followed-up until December 2020. Diagnosis of HZ was made according to clinical manifestations: skin rash, blisters, paresthesia and local pain in one or more dermatomes. Results: We studied 392(309women/83men), mean age 59±13years. Every patient was followed-up during a mean period of 137±110 months (range: 42months- 42years). HZ infection was observed in 30 of 392 (25women/5men) patients; age (mean±SD) 64.7±11.8years. Prevalence was 7.65% in this period and incidence rate was 13.22/1000patients/year. Three patients had facial involvement, one with optic involvement and one patient presented a disseminated HZ. Seven patients presented postherpetic neuralgia treated with gabapentinoids. The main features of RA of these 30 patients were: positive RF(n=17; 56.6%), positive anti-CCP(13; 43.3%) and erosive disease(10; 33.3%). At HZ infection they were in treatment with glucocorticoids (19; 63.3%), conventional DMARDs (15; 50%), biological DMARDs (15; 50%), tofacitinib (2; 6.6%) and upadacitinib (1; 3.3%). Conclusions: HZ is a relative frequent viral complication of RA patients. In our series, one patient presented a disseminated HZ and nearly 25% of patients had post-herpetic neuralgia. Include HZ vaccine in our vaccination program in RA patients may be beneficial.

Coagulase negative Staphylococci (CoNS) are reported to be responsible for 50-60% of bloodstream infections in very preterm (&lt;1500 g) infants in Neonatal Intensive Care Units (NICU). Staphylococcus capitis is an increasingly prevalent pathogen in neonatal setting, frequently causing central-line associated bloodstream infections (CLABSI) that can be difficult to eradicate. CVC removal versus in situ treatment of CoNS CLABSIs is a matter of debate, with no clear consensus emerging in the existing literature. We revised all S. capitis CLABSIs in our NICU between 2019 and 2022, focusing on the role of catheter removal for eradication. Among 25 cases, 17 CVCs were removed after diagnosis, leading to a 76.5% eradication rate in this group. 3 infants had a persistently positive blood culture after CVC substitution. A new catheter was than inserted after a 48-hours washout period, resulting in resolution of the infection. Only 2 of 8 patients (25%) who retained the catheter after diagnosis, underwent infection eradication with antibiotic therapy alone. Catheter removal, when feasible, seems to be the most effective strategy to eradicate S. capitis CLABSIs, sometimes even requiring a 48-hours washout period before reinsertion. Further studies on this subject are needed to better standardize the management of this kind of infections.

Background: Application of enhanced recovery after surgery principles decrease postoperative complications (POCs), length of stay (LOS), and readmissions. Pharmacoprophylaxis decreases morbidity, but the effect of specific regimens on clinical outcomes is unclear. Methods and Materials: Records of 476 randomly selected adult patients who underwent elective colorectal surgeries (ECRS) at 10 US hospitals were abstracted. Primary outcomes were surgical site infection (SSI), venous thromboembolism (VTE), postoperative nausea and vomiting (PONV), pain, and ileus rates. Secondary outcomes included LOS and 7- and 30-day readmission rates. Results: POC rates were SSI (3.4%), VTE (1.5%), PONV (47.9%), pain (58.1%), and ileus (16.1%). Cefazolin 2g/metronidazole 500mg and ertapenem 1g were associated with the shortest LOS; cefotetan 2g and cefoxitin 2g with the longest LOS. No SSI occurred with ertapenem and cefotetan. More Caucasians than Blacks received oral antibiotics before intravenous antibiotics without impact. Enoxaparin 40 mg subcutaneously daily was the most common inpatient and discharge VTE prophylaxis. All in-hospital VTEs occurred with unfractionated heparin. Most received rescue rather than around the clock antiemetics. Scopolamine patch, spinal opioids, and IV lidocaine continuous infusion were associated with lower PONV. Transversus abdominis plane block with long-acting local anesthetics, celecoxib, non-anesthetic ketamine bolus, ketorolac IV, lidocaine IV, and pregabalin were associated with lower in-hospital pain severity rate. Gabapentinoids and alvimopan were associated with lower ileus rate. Acetaminophen, alvimopan, famotidine, and lidocaine patch were associated with shorter LOS. Conclusions: Significant differences in pharmacotherapy regimens that may improve primary and secondary outcomes in ECRS were identified. Future research should identify latent pharmacotherapy variables that impact patient outcomes.

Background: PFO (Patent foramen ovale) is a common defect that affects about 25% of the population. Although its presence is asymptomatic in the majority of the cases, the remaining part becomes overt with different symptoms, including cryptogenic stroke. The PFO closure procedure is widely available to date with the most used Amplatzer PFO Occluder, also in complex anatomy, but the performance of another device, the GORE Septal Occluder (GSO), has not been completely explored with regard to different septal anatomies. Methods: From March 2012 to June 2020, 118 consecutive patients with an indication for PFO closure were treated using the GSO system and included in a prospective analysis and followed. After 12 months, every patient underwent transcranial Doppler to evaluate the effectiveness of treatment. Results: of 111 patients evaluated, 107 showed effective PFO closure (96,4%) and 4 showed a residual shunt (3,6%). To better evaluate the device performance, the overall population was sorted into 2 clusters based on the echocardiographic characteristics. The main difference between groups was for PFO width (4,85 ± 1,8 vs 2,9 ± 1 mm, p <0,001) and PFO tunnel length (12,6 ± 3,8 vs 7,2 ± 2 respectively, p <0,001), allowing identification of complex anatomy and simple anatomy, respectively. Regardless of the aforementioned cluster, the GSO performance to reach an effective closure was independent of anatomy type and the chosen device size. Conclusion: GSO device showed efficacy and safety at 1-year follow-up in patients with at least 1 anatomical factor of complexity of PFO, irrespectively from the level of complexity itself.

Background: Hypertension is a condition of a person's blood pressure being at a level above normal, hypertension treatment can be done herbally using avocado leaves. Avocado leaves can lower blood pressure because they contain active substances, namely flavonoids and quercetin. This research was conducted in the working area of the Tilango Health Center. Objective: This study aims to determine the effect of giving boiled water of avocado leaves on reducing blood pressure in the elderly with hypertension. Methods: Design This study used a two-group quasi-experimental pre-test - post-test design. The sample is the elderly who have hypertension, amounting to 125 people with purposive sampling technique. The research instrument used a questionnaire. Results: Statistical test using T-Test on blood pressure before and after the intervention was given a significance value of 0.000 (p-value < 0.05 ). Conclusion : This study concludes that there is a significant effect between giving avocado leaf boiled water on reducing blood pressure in the elderly with hypertension in the working area of the Tilango Health Center.

Systemic sclerosis is an autoimmune disease characterized by organ fibrosis and vasculopathy. Almost all patients suffer from Raynaud’s phenomenon (RP). Currently, several imaging techniques are available; nailfold video capillaroscopy (NVC) is the most widely available, but flow quantification is not possible with NVC. Novel imaging techniques are of interest in this population. We performed a single-center feasibility study using Micro Vascular Imaging (MVI) as a novel imaging technique for flow quantification of small fingertip vessels. We compared a group of 20 healthy controls (HCs) with 20 Systemic Sclerosis (SSc) patients. In HCs, flow measurements assessed with MVI were statistically significantly higher in individual fingers and combined for all fingers (p&lt;0.0001). As a cut-off value to discriminate HCs from SSc, a peak systolic (PS) flow velocity of &lt;6.9 cm/s and an end-diastolic (ED) flow velocity of &lt;2.68 cm/s was determined. Test characteristics for PS flow velocity showed moderate sensitivity (0.69, 95% CI 0.58-0.78) but high specificity (0.88, 95% CI 0.79-0.93). Similar test characteristics for ED flow velocity were obtained. The optimal cut-off point was estimated at &lt;2.68 cm/s, sensitivity was moderate (0.65, 95% CI 0.53-0.75), specificity was 0.80 (95% CI 0.70-0.87). Here, we present the first study on the use of MVI to assess blood flow in the fingertips with high specificity in SSc patients. Future studies need to investigate correlations with the risk for organ complications, such as digital ulcers or pulmonary arterial hypertension.

Lipid droplet (LD) accumulation in hepatocytes is one of the major symptoms associated with fatty liver disease. Mitochondria play a key role in catabolizing fatty acids for energy production through β-oxidation. The interplay between mitochondria and LD assumes a crucial role in lipid metabolism, while it is obscure how mitochondrial morphology affects systemic lipid metabolism in the liver. We previously reported that cilnidipine, an already existing anti-hypertensive drug, has potency to prevent pathological mitochondrial fission by inhibiting protein-protein interaction between dynamin-related protein 1 (Drp1) and filamin, an actin-binding protein. Here, we found that cilnidipine and its new dihydropyridine (DHP) derivative, 1,4-DHP, which lacks Ca2+ channel blocking action of cilnidipine, prevent the palmitic ac-id-induced Drp1-filamin interaction, LD accumulation and cytotoxicity of human hepatic HepG2 cells. Cilnidipine and 1,4-DHP also suppressed the LD accumulation accompanied by reducing mitochondrial contact with LD in obese model and high fat diet-fed mouse livers. These results propose that targeting Drp1-filimin interaction becomes a new strategy for the prevention or treatment of fatty liver disease.

Follicular helper CD4+ T cells (TFH) are a major cellular pool for the maintenance of HIV reservoir. Therefore, the delineation of the follicular (F)/germinal center (GC) immune landscape will significantly advance our understanding of HIV pathogenesis. We have applied multiplex confocal imaging, in combination with relevant computational tools, to investigate, F/GC in situ immune dynamics in viremic (vir-HIV), antiretroviral treated (cART HIV) People Living With HIV (PLWH) and compare them to reactive, non-infected controls. Lymph nodes (LNs) from viremic and cART PLWH could be further grouped based on their TFH cell densities in high-TFH and low-TFH subgroups. These subgroups were also characterized by different in situ distribution of PD1hi TFH cells. The significantly accumulated follicular, compared to extrafollicular, FOXP3hi CD4+ T cells found in the low-TFH cART-HIV group were characterized by a less scattered in situ distribution and strongly correlated with the cell density of CD8+ T cells in this group. An inverse correlation between plasma viral load and LN GrzBhiCD8+ T and CD16hiCD15lo cells was found. Our data reveal the complex GC immune landscaping in HIV infection and suggest that follicular FOXP3hi CD4+ T cells could be negative regulators of TFH cell prevalence in cART-HIV.

Sea ice roughness can serve as a proxy for other sea ice characteristics such as ice thickness and ice age. Arctic-wide maps that represent spatial patterns of sea ice roughness can be used to better characterize spatial patterns of ice convergence and divergence processes. Sea ice surface roughness can also control and quantify turbulent exchange between sea ice surface and atmosphere and therefore influence surface energy balance at the basin scale. We have developed a data processing system that produces georeferenced sea ice roughness rasters that can be mosaicked to produce Arctic-wide maps of sea ice roughness. This approach starts with Top-of-Atmosphere radiance data from the Multi-angle Imaging SpectroRadiometer (MISR). We used red-band angular data from three MISR cameras (Ca, Cf, An). We created a training data set in which MISR pixels were matched with co-located and concurrent lidar-derived roughness measurements from the Airborne Topographic Mapper (ATM). We used a K-nearest neighbor algorithm with the training data to calibrate the multi-angle data to values of surface roughness and then applied the algorithm to Arctic-wide MISR data for two 16-day periods in April (spring) and July (summer). After georeferencing the roughness rasters, we then mosaicked each 16-day roughness dataset to produce Arctic-wide maps of sea ice roughness for spring and summer. Assessment of the results shows good agreement with independent ATM roughness data, not used in model development. A preliminary exploration of spatial and seasonal changes in sea ice roughness for two locations shows the ability to characterize the roughness of different ice types and the results align with previous studies. This processing system and its data products can help the sea ice research community to gain insights into the seasonal and interannual changes in sea ice roughness over the Arctic.

Background This study aimed to examine the acute effects of different pre-ST strategies on muscular performance and blood pressure (BP) responses in recreationally strength-trained women. Methods: Twelve overweight women with normal-to-elevated BP were recruited and performed six exper-imental protocols in a randomized order: 1) control protocol (CC) – BP assessed without exercises performed, 2) strength training (ST), 3) foam rolling warm-up followed by strength training (FR+ST), 4) specific warm-up followed by strength training (SW+ST), 5) aerobic exercise followed by strength training (AE+ST), and 6) stretching exercises followed by strength training (SE+ST). Strength training consisted of three sets at 80% of 10RM with a self-suggested rest interval between sets for bench press, back squat, bench press 45º, front squat, lat pull-down, leg press, shoulder press, and leg extension. Results: All experimental protocol had a lower total training volume, fa-tigue index, and repetitions performance in relation to ST (p

In recent years, it has been found in engineering practice that the service life of cemented carbide shield machine tools used in uneven soft and hard strata is substantially reduced. The study found that thermal stress is the main reason for the failure of cemented carbide shield tunneling tools when shield tunneling is carried out in uneven soft and hard soil. To maintain the hardness of cemented carbide, improving the thermal conductivity of the shield machine tool is of great importance for prolonging its service life and reducing engineering costs. In this paper, graphene and carbon nanotubes were mixed with WC-Co powder and sintered by SPS (Spark Plasma Sintering). The morphology was observed by using scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDS). A Rockwell hardness tester and bending strength tester were used to test hardness, bending strength and thermal conductivity. The results show that adding trace graphene or carbon nanotubes can increase the bending strength of the cemented carbide by approximately 50% while keeping the hardness of the cemented carbide unchanged. The thermal conductivity of the cemented carbide can be increased by 10% with the addition of 0.12% graphene alone.

A new formalism is introduced that makes it possible to elucidate the physical and geometric content of quantum spacetime. It is based in the Minimum Group Representation Principle (MGRP). Within this framework new results for entanglement and geometrical/topological phases are found and implemented in cosmological and black hole space-times. Our main results here are: {\bf(i)} We find the Berry phases for inflation and for the cosmological perturbations and express them in terms of the observables, as the spectral scalar and tensor indices, $n_S$ an $n_T$, and the tensor to scalar ratio $r$. The Berry phase for de Sitter inflation is imaginary with the sign describing the exponential acceleration. {\bf(ii)} The pure entangled states in the minimum group (metaplectic) $Mp(n)$ representation for quantum de Sitter space-time and black holes are found. {\bf(iii)} For entanglement, the relation between the Schmidt type representation and the physical states of the $Mp(n)$ group is found: This is a {\it new non-diagonal} coherent state representation complementary to the known Sudarshan diagonal one. {\bf(iv)} Mean value generators of $Mp(2)$ are related to the adiabatic invariant and topological charge of the spacetime (matrix element of the transition $-\infty < t < \infty$). {\bf(v)} The basic {\it even} and {\it odd} $n$-sectors of the Hilbert space are intrinsic to the quantum spacetime and its discrete levels (in particular continuum for $n \rightarrow \infty$), they do not require any extrinsic generation process as the standard Schrodinger cat states, and are {\it entangled}. {\bf(vi)} The gravity or cosmological domains in one side and another of the Planck scale are {\it entangled}. Examples: The quantum primordial trans-Planckian de Sitter vacuum and the classical late de Sitter vacuum today; the central quantum gravity reqion and the external classical gravity region of black holes. The classical and quantum dual gravity regions of the space-time are entangled. {\bf(vii)} The general classical-quantum gravity duality is associated to the Metaplectic $Mp(n)$ group symmetry which provides the complete full covering of the phase space and of the quantum space-time mapped from it.

The 2020-2025 Dietary Guidelines for Americans recommends limiting intakes of saturated fat and added sugars (SF/AS) to 88% of the representative sample of U.S. adults. The top sources of SF were cheese, pizza, ice cream, and eggs. The leading sources of AS were soft drinks, tea, fruit drinks, and cakes and pies. This analysis reflects a parsimonious approach to reliably identify foods and beverages that contribute to SF/AS intakes in U.S. adults.

The aim of this pilot study is to evaluate and compare the quality of the genomics and proteomics data obtained from paired formalin fixed paraffin embedded (FFPE) and frozen (FF) tissue percutaneous core biopsies of LIRADS 5 hepatocellular carcinoma (HCC) of varying histological grade. The preliminary data identified differentially expressed proteins and genes in poor, moderate and well differentiated HCC biopsies, with a greater efficacy in fresh frozen samples.

In this part of the two-part series of essays, we first derive some equations for further physical redshift distances. We then analyze a catalog with 132,975 quasars, for which both the apparent magnitude m and the redshift z are given, in order to find the today’s value of the parameter β₀ of the theory presented. We then use this value to determine the today’s value of the radius R_0a of the Friedmann sphere using a magnitude redshift diagram of 19 SNIa. With the help of the known values of R_0a and β₀, statements about astrophysical data from the black hole in the galaxy M87 can be made. In addition, the today’s Hubble parameter H₀ results from both parameters. Furthermore, we calculate the values of the further physical redshift distances for the black hole in M87 and all 19 SNIa. The resulting parameter values are: β₀ ≈ 0.731, R_0a ≈ 2,712.48 Mpc and H₀ ≈ 65.638 km / (s ∙ Mpc). The today’s mass density of the Friedmann sphere is ρ₀ ≈ 4.843 x 10^-27 g / cm 3. For the mass of the Friedmann sphere we find M_FK ≈ 1.206 x 10⁵⁶ g. Annotation: Knowledge of the first part [1] of the series of articles is a prerequisite for understanding this article.

The pathology of idiopathic intracranial hypertension (IIH), a disease characterized by papillary edema and increased intracranial pressure (IICP), is not yet understood; this disease significantly affects quality of life due to symptoms, including vision loss, headache, and pulsatile tinnitus. By contrast, superficial siderosis (SS), a disorder in which hemosiderin is deposited on the surface of the cerebral cortex and cerebellum, potentially causes cerebellar ataxia or hearing loss. So far, no cases of IIH with infratentorial and supratentorial cortical SS have been reported. Herein, we report a case of a 31-year-old woman with obesity who developed this condition. The patient suddenly developed headache and dizziness, had difficulty walking, and subsequently became aware of diplopia. Fundus examination revealed bilateral optic nerve congestive papillae and right eye abducens disturbance. Head magnetic resonance imaging (MRI) showed prominent SS on the cerebellar surface and cerebral cortex. Lumbar puncture revealed IICP of 32 cmH2O, consistent with the diagnostic criteria for IIH, and treatment with oral acetazolamide was started; subsequently, the intracranial pressure decreased to 20 cmH2O. Her abduction disorder disappeared, and the swelling of the optic papilla improved. She was now able return to her life as a teacher without any sequelae. SS is caused by persistent slight hemorrhage into the subarachnoid space. In this case, both infratentorial and supratentorial cortical superficial SS was observed. Although cases of IIH complicated by SS are rare, it should be kept in mind that a causal relationship between IIH and SS was inferred from our case. Our findings also suggest that cerebrospinal fluid dynamic analysis using MRI is effective in diagnosing IIH and in determining the efficacy of treatment.

Seroconversion surveys of anti-SARS-CoV-2 antibodies provide accurate estimates of the SARS-CoV-2 infection. This nationwide population-based cross-sectional serosurvey aimed to evaluate the prevalence of SARS-CoV-2 antibodies among residents in Gabon and compare the estimated cumulative number of COVID-19 cases with the officially registered number of laboratory-confirmed cases up to December 2021. Households in each province were randomly selected. Twenty-eight localities including 16 urban and 12 rural, were randomly selected to participate in the study. Whole blood samples were collected in dry tubes from all study participants around the country within 15 days. Serum samples were used to measure the total Immunoglobulin antibodies. Overall, data of 1672 households were analyzed. Out of the 3659 participants, 3175 were found positive for SARS-CoV-2 antibodies, resulting in a crude seroprevalence of 86.77%. Stratification of study participants by age group has shown highest seroprevalences in 20–29 and 40-49 age groups with 91.78% (95% CI:89.5–93.6) and 91.42% (95% CI:88.7–93.5), respectively. Nyanga province had the lowest prevalence (72,8%), and Estuaire and Ogoué-Lolo provinces had the highest prevalence (90 and 92%, respectively). Our results suggest a high transmission rate in the Gabonese population, 21 months after the first SARS-CoV-2 case in the country. This high seroprevalence estimate could indicate that the applied infection control measures may not have been adequately implemented or appropriately adhered to by the population.

Keywords: gut microbiota; small intestinal bacteria overgrowth; SIBO; diet, dysbiosis; microbial ecology.

The flow behavior of the administrated fluid matrices demands careful assessments for stability as consumed by individuals with dysphagia. In the present study, we incorporate tapioca starch (TS), hydroxypropyl distarch phosphate (HDP), and xanthan gum (XG) as thickeners into different nectars (300±20 mPa.s) undergoing thermal processing and evaluated their stability. The thickened nectars presented better water holding and oil binding capacities at 25 ℃ than 4 ℃, and the nectars with TS provided the best results for both capacities as well as the highest solubility index and swelling power (p<0.05). All prepared nectars appeared to be shear-thinning fluids with yield stress closely fitting the power law and Casson models. XG-contained nectars presented a higher yield stress and consistency index. Matrices thickened by HDP exhibited a higher viscoelastic property compared to those thickened by TS during thermal processing. TS nectars presented viscous behavior, whereas HDP and XG nectars presented elastic behavior at 80 ℃ processing. The 3-min thermal processing HDP-nectars remained stable and met dysphagia-friendly requirements under 4 ℃ storage for 28 days regardless of the types of fluid bases (distilled water, sport drink, or orange juice). The employed thickeners present adequate physicochemical properties to be potentially utilized for producing dysphagia-friendly formulations.

Background: Gastric cancer (GC) is the second most prevalent cancer in Korea, significantly impacting morbidity and mortality. While advancements in early detection and treatment have improved survival rates, managing post-surgical recovery remains vital. Herbal medicine (HM) has emerged as a potential adjunct therapy to enhance recovery and quality of life (QoL) in patients post-GC surgery. Methods: This systematic review and meta-analysis evaluated the efficacy and safety of HM in the post-surgical recovery of GC patients. We searched both Korean and international databases, identifying 16 randomized controlled trials (RCTs) meeting our criteria. We assessed study quality using the Cochrane Risk of Bias tool and analyzed data with Review Manager Software (RevMan). Results: Our analysis included 1,546 patients from the selected studies, demonstrating that HM significantly improved gastrointestinal recovery times, including time to first flatus, bowel movement, and return of bowel sounds. Significant improvements were also seen in nutritional markers such as albumin and prealbumin, alongside beneficial effects on immune markers like CD3+ and CD4+ levels. QoL assessments using WHOQOL-BREF and QLQ-C30 scores indicated substantial improvements. HM had a favorable safety profile, showing a reduced incidence of adverse effects compared to controls. Conclusion: The findings suggest that HM can significantly enhance recovery and improve the quality of life following gastric cancer surgery, with a favorable safety profile. However, due to considerable heterogeneity in study results, extended clinical trials and rigorous follow-ups are recommended to assess long-term effects and side effects comprehensively.

Lung cancer (LC) continues to be an important public health problem being the most common form of cancer and a major cause of cancer deaths worldwide. Despite the great bulk of research to identify genetic susceptibility genes by genome-wide association studies, only few loci associated to nicotine dependence have been consistently replicated. Our previously published study in few phenotypically discordant sib-pairs identified a combination of germline truncating mutations in known cancer susceptibility genes in never smoker early-onset LC patient does not present in their healthy sib. These results firstly demonstrated the presence of an oligogenic combination of disrupted cancer predisposing genes in non-smokers patients, giving experimental support to a model of a “private genetic epidemiology”. Here, we used a combination of whole-exome and RNA sequencing coupled with a discordant sib’s model in a novel cohort of pairs of never-smokers early-onset LC patients and in their healthy sibs used as controls. We selected rare germline variants predicted as deleterious by CADD and SVM bio-informatics tools and absent in the healthy sib. Overall, we identified an average of 200 variants per patient, about 10 of which in cancer predisposing genes. In most of them, RNA sequencing data reinforced the pathogenic role of the identified variants showing: i) downregulation in LC tissue (indicating “second hit” in tumor suppressor genes); ii) upregulation in cancer tissue (likely oncogene); iii) downregulation in both normal and cancer tissue (indicating transcript instability). The combination of the two techniques demonstrates that each patient has an average of six (with a range from four to eight) private mutations with functional effect in tumor predisposing genes. The presence of a unique combination of disrupting events in the affected subjects may explain the absence of familial clustering of non-small cell lung cancer. In conclusion, these findings indicate that each patient has his/her own “predisposing signature” to cancer development and suggest the use of personalized therapeutic strategies in lung cancer.

Herein, we examined the effects of weather parameters and individual clinicodemographic risk factors on hemorrhagic stroke (HS) incidence, severity on admission, and disability at discharge in a harsh desert climate. In a retrospective design we studied patients admitted to a stroke unit in Arab Emirates in 2016-2019. With a distributed lag nonlinear model we explored immediate and delayed effects of weather on stroke incidence. Supervised machine learning was used to build models predictive of scores in NIHSS and mRS scales. We assessed model performance by calculating ROC AUC, F1 scores, specificity, and sensitivity. HS risk increased after a significant change in any weather parameter. The risk was reduced below baseline after 1-week adjustment to environmental changes. Climate input from the previous 3 days yielded reliable classification models. Humidex was a better predictor of severity than air temperature, whereas body mass index, age, and time of day at stroke onset were the strongest clinical predictors. Weather parameters before admission were stronger predictors of disease severity than individual clinical factors. We addressed limitations of previous studies by analyzing a full set of climate parameters: ambient temperature, relative humidity, humidex, atmospheric pressure, and wind speed. Predictive models may help to optimize patient management and develop preventative strategies.

Resveratrol (RSV), a naturally occurring phytoalexin, is the most important stilbenoid synthesized by plants, as a defense mechanism, in response to microbial aggression, toxins or ultraviolet radiation. RSV came to the attention of researchers both as a potential chemopreventive agent and a possible explanation for the low incidence of cardiovascular disease (CVD) in French people with a high-fat diet. RSV is mainly administered as a food supplement, its properties being evaluated in vitro or in vivo, on various experimental models. RSV modulates signaling pathways that limit the spread of tumor cells, protects nerve cells from damage, is useful in the prevention of diabetes, and generally acts as an anti-aging natural compound. It was highlighted that RSV could ameliorate the consequences of an unhealthy lifestyle caused by an exaggerated caloric intake. This paper reviews the evidence supporting the beneficial effect of RSV for various pathological conditions, e.g., neoplastic diseases, neurodegeneration, metabolic syndrome, diabetes, obesity, CVDs, immune diseases, bacterial, viral, and fungal infections. The study also focused on the chromatographic analysis of trans-RSV (tRSV) in Romanian wine samples, providing a comprehensive overview of tRSV content across different types of wine.

Nanoparticles have been used as a novel drug delivery system. Drug-incorporated nanoparticles for local delivery might optimize the efficacy and minimize the side effects of drugs. The efficacy and safety of intratracheal administration of prostacyclin analog (beraprost)-incorporated nanoparticles and imatinib, a PDGF-receptor tyrosine kinase inhibitor, -incorporated nanoparticles in Sugen-hypoxia-normoxia or monocrotaline rat models of PAH and in human PAH-pulmonary arterial smooth muscle cells have been reported. The use of inhaled drug-incorporated nanoparticles might be a novel approach for treatment of PAH.

Excessive oxidative stress and exercise-induced fatigue reduce physical performance and can lead to dysfunction in antioxidant systems within muscular and hepatic tissues. Integrating natural substances with exercise may mitigate fatigue via anti-oxidant effects. This study aims to compare and evaluate the effects of exercise and supplementation with Sundarbans honey vs energy drinks on the strength, anxiety physiological profiles, and hepatic antioxidant capacity in mice undergoing extraneous exercise and fatigue. Forty-eight four-week-old Swiss albino mice were randomly assigned to one of eight groups: (1) Control, (2) Speed™ (Sp), (3) Royal Tiger™ (RT), (4) Sundarbans Honey (SH), (5) Exercise (Ex), (6) Exercise + Sundarbans Honey (Ex+SH), (7) Exercise + Speed™ (Ex+Sp), and (8) Exercise + Royal Tiger™ (Ex+RT). Supplements were administered via oral gavage: Sp (2.5 ml/kg BW), RT (2.5 ml/kg BW), and SH (1 g/kg BW), four times a week for 60 days. Mice in the Ex, Ex+SH, Ex+Sp, and Ex+RT groups underwent daily swimming and running. The strength, fatigue, anxiety levels, lipid profiles, and antioxidant biomarkers were evaluated post-treatment. The SH, Ex, and Ex+SH groups exhibited significantly enhanced physical performance (p

The study aimed to compare the cardiovascular benefits of Omega-3 Polyunsaturated Fatty Acids from fish oil versus krill oil in different forms and dosages. Following PRISMA 2015, data analysis with R software, and databases were searched from 1993 to 2023, (ID PROSPERO: CRD42024502338). Sixty high-quality studies were analyzed, covering various forms of fish oil and krill oil at different dosages (fish oil (ethyl ester-EE, triglyceride-TG, re-esterified triglycerides-rTG, capsules, emulsion-EM); krill oil (phospholipid/free fatty acid-PL/FFA, high concentration phospholipid-HPL, low concentration phospholipid-LPL)). Meta-analysis revealed that krill oil with phospholipid/free fatty acid at doses 2000-2900 mg effectively lowered triglycerides, while fish oil in ethyl ester form at doses above 3000 mg significantly reduced total cholesterol. Fish oil in triglyceride form at doses 2000-2900 mg and other variations positively impacted HDL-C levels. Fish oil in EE form above 3000 mg and triglyceride form below 2000 mg notably reduced LDL-C. However, there was limited effectiveness observed for other interventions. Analysis for LDL-C exhibited publication bias, while other parameters demonstrated reliability (Egger's test). In conclusion, krill oil - PL/FFA, Fish oil - EE above 3000 mg, Fish oil - TG 2000-3000 mg, and fish oil - rTAG 300-1900 mg effectively in reducing heart risk patients.

Cardiovascular disease (CVD) is the leading cause of death worldwide. Cardiac rehabilitation (CR) has proven to be effective in reducing the rate of recurrence and disease as secondary prevention (evidence-based intervention) in patients who have suffered from myocardial infarction (MI). CR is a multidisciplinary path in which the patient is followed pharmacologically, from a psychological, nutritional, nursing and physiotherapy point of view. Post-MI patients present a reduction in the performance of the diaphragm muscle, the main inspiratory muscle, and this condition can become a risk factor for further relapses or for the onset of heart failure. Despite the solidity of the international guidelines for CR, the latter are lacking in specifically indicating an evaluation and training path regarding the inspiratory muscles in post-MI patients who have not undergone cardiac surgery. The article reviews the information on the adaptation of the diaphragm post-MI and highlights the need for clearer indications for a rehabilitation process that gives importance to the diaphragm.

Progress in laser-driven proton acceleration requires increasing the proton maximum energy and laser-to-proton conversion efficiency, while reducing the divergence of the proton beam. However, achieving all these qualities simultaneously has proven challenging experimentally, the increase in beam energy often coming at the cost of beam quality. Numerical simulations suggest that coupling multi-PW laser pulses with ultrathin foils could offer a route for such simultaneous improvement. Yet experimental investigations have been limited by the scarcity of such lasers and the need for very stringent temporal contrast conditions to prevent premature target expansion before the pulse maximum. Here, combining the newly commissioned Apollon laser facility that delivers high-power ultrashort (∼24fs) pulses, with a double plasma mirror scheme to enhance its temporal contrast, we demonstrate the generation of up to 35 MeV protons with only 5 J of laser energy. This approach also achieves improved laser-to-proton energy conversion efficiency, reduced beam divergence, and optimized spatial beam profile. Therefore, despite the laser energy losses induced by the plasma mirror, the proton beams produced by this method are enhanced on all accounts compared to those obtained under standard conditions. Particle-in-cell simulations reveal that this improvement results from the intensified electrostatic field caused by a more compact hot-electron distribution.

There are important challenges for modeling large electrical distribution circuits, even more with the presence of distributed renewable generation. Constructing simulations for assessing the effect of the penetration of distributed generation on electrical distribution networks has become of great importance for Distribution Network Operators (DNOs). This paper proposes a simulation strategy based on open-source platforms and the integration of scripting tools for the rapid modeling of large-scale electrical distribution circuits with distributed renewable generation. The implementation is based on the adaptation of a tool called QGIS2OpenDSS, which creates OpenDSS distribution network models directly from an open-source geographic information system, QGIS. The plugin’s capabilities are demonstrated using a real distribution feeder with more than 60% penetration of renewable generation based on photovoltaic systems. These simulations are carried out using real data from a circuit provided by a DNO in the Dominican Republic, which is used to demonstrate how this approach provides a more accessible and flexible way to simulate and assess the effect of Distributed Energy Resources (DERs) in Medium Voltage (MV) and Low Voltage (LV) networks, enabling utilities to evaluate system performance and identify potential issues.

The responses of inflammatory cytokines and brain-derived neurotrophic factor (BDNF) to a high-intensity interval training (HIIT) session were compared between 7 postmenopausal (57±2 y) and 8 premenopausal females (44±3 y) during the luteal phase of their menstrual cycle, when estrogen and progesterone are highest, and. HIIT consisted of 10 x 1 min running intervals (90% maximum heart rate) separated by 1 min recovery intervals. Blood samples were collected at baseline (fasted), pre-exercise (postprandial), and 0, 30 and 90 min post-HIIT and analyzed for interleukin (IL-6) and 10 (IL-10), tumour necrosis factor-alpha (TNF-α) and BDNF. IL-6 significantly increased from pre-exercise to 0 min post-HIIT in postmenopausal (+40%, p=0.01) but 30 min post-HIIT in premenopausal females (+60%, p=0.02). IL-6 remained elevated at 90 min post-HIIT in premenopausal (+104%, p=0.05) and to a higher degree in postmenopausal (+385%, p&lt;0.001). IL-10 showed no response. TNF-α increased from pre- to 0 min post-HIIT (+10%, p=0.05), then decreased to below pre-exercise at 30 min (-10%, p=0.02) and 90 min (-5%, p=0.04) in both groups. BDNF increased immediate post-HIIT in premenopausal (+60%, p&lt;0.001) but not postmenopausal females. The differences in IL-6 and BDNF response to HIIT between pre and postmenopausal females provide evidence of the role of female reproductive hormones in the regulation of these exercise-induced responses.

Our report presents the findings from a treatment program that involved plant-based diets (PBDs) and supplements for 1,750 elderly cardiology patients diagnosed with COVID-19 between April 2020 and June 2023. At the start of the program, there was no published data supporting the use of PBDs for COVID-19 patients. However, after 18 months, studies were released that indicated the effectiveness of PBDs in decreasing the incidence and severity of COVID-19. Our treatment protocol differed from these studies in several ways. We carefully controlled the quality, quantity, and processing method of the foods we provided, opting for raw instead of cooked vegetables. Additionally, we incorporated supplementation that complemented the nutrients lacking in a PBD and enhanced the anti-viral, anti-inflammatory, antioxidant, antithrombotic, and immunomodulatory properties of a PBD. Our patients recovered faster (12±1.4 days vs. 20.9±4.3 days), with lower severity (2% vs. 10-20%), hospitalizations (0 vs. 5-10%), and deaths (0 vs. 15-17%) compared to the general population. These favorable outcomes are particularly noteworthy given Indonesia's high COVID-19 morbidity and mortality rates, among the highest in Asia. The findings of this report provide valuable insights for practitioners in managing high-risk elderly COVID-19 patients, particularly in avoiding severity and mortality.

In a 24-week-long experiment, 31 rats were assigned to one of 3 groups: a Control group receiving standard chow and water, a Fructose group receiving standard chow and a 20% fructose solution, or an STZ+lipids group that received a fat-enriched diet following a single 25 mg/kg streptozotocin injection at the onset of the diet. Both groups experienced significantly increased caloric intake but did not gain weight above the Control group level. Adipocytes in subcutaneous and visceral adipose depots of both groups had smaller size compared to control and higher density in tissue. Respirometric analyses unveiled a substantial increase in mitochondrial respiration across all adipose tissue types in both dietary intervention groups, with greater changes observed in the Fructose group. Correlation analyses demonstrated that in both experimental groups high tissue respiration is associated with better biochemical profile and closer to control adipose tissue morphology. Increased tissue respiration in adipose depots could be an important mechanism of resilience to excessive caloric intake.

Capacitor banks are widely used in current electrical transmission systems in order to improve power quality and increase efficiency. Utilizing high voltage components such as, shunt capacitors in the power grid imposes new challenges to the system which are required to be addressed. One of these challenges is corona discharges that can have negative impacts on capacitor banks such as power loss, insulator erosion followed by equipment failure, and radio interference. Although previous studies have almost exclusively focused on optimization of corona suppression rings for transformers and transmission lines, no specific studies have conducted regarding high voltage capacitor banks. This paper presents a novel study concerning verification and development of corona discharge suppression models on AC and DC capacitor banks with two different voltage levels. The employed method is based on the Maxwell’s equations and finite element method (FEM) which is implemented with the help of COMSOL Multiphysics© software. Results have verified the necessity of suppression methods as well as the efficiency of proposed solutions. Corona inception voltage levels are identified and effective factors on its appearance are reviewed. Analyses of proposed solutions have shown significant improvements in optimization of corona suppression methods as well as enhancement of maintenance maneuverability.