Boost-derived converters are most popular in Power Factor Correction AC-DC conversion applications and alternative energy generation systems. The proper operation of such converters relies on housekeeping power supplies providing auxiliary power for their control circuitry. The purpose of this study is to present a design-oriented analysis of a simple, passive, isolated, self-bias circuit that can provide a stabilized voltage for the control circuits of boost-derived converters. The circuit’s output voltage inherently follows the main regulated output and therefore, does not require an additional active control. The paper presents a detailed analysis of the circuit and offers design guidelines. Following the presentation of the basic idea several variations of the circuit, that can be used in special applications, are presented. The feasibility of the proposed bias circuits was verified by simulation and experiment on a laboratory prototype.

DSSC devices are among the most widely studied thin-film solar cells because of their cost-effectiveness, low toxicity, and simple fabrication method. However, there is still much scope for replacing current DSSC materials due to their high cost, low volume, and lack of long-term stability. Accordingly, ITO-nanorod films were fabricated by E-beam evaporation using the glancing angle deposition method in this study. Then, the ITO-nanorod was treated by oxygen plasma via a bias-magnetron RF sputtering process to improve the efficiency of DSSC under a varying gas flow rate of 20, 40, 60, 80, and 100 sccm. The FE-SEM investigation of the ITO film structure revealed that the obtained nanorod structures have slightly different diameters. At the same time, an increase in the oxygen flow rate resulted in a rougher film surface structure. In this, the lower sheet resistance was received because of rougher morphology. When comparing the DSSC efficiency test results, we found that at a gas flow rate of 100 sccm, the highest efficiency value showed by 9.5%. On the other hand, the ITO-nanorod without plasma treatment exhibited the lowest efficiency. Hence, plasma technology can be practically applied to improve the efficiency of DSSC devices. This study will be a prototype of a highly advanced solar cell manufacturing method for the solar cell industry.

This article presents a self balanced multistage DC-DC step-up converter for photovoltaic applications. Proposed converter topology is designed for unidirectional power transfer and provides a doable solution for photovoltaic applications where voltage is required to be stepped up without magnetic components (Transformer-less and Inductor-less). The output voltage obtained from renewable sources will be low and must be stepped up by using a DC-DC converter for photovoltaic applications. K diodes and K capacitors along with two semiconductor control switch are used in the K-stage proposed converter to obtain an output voltage which is (K+1) times the input voltage. The conspicuous features of proposed topology are i) Magnetic components free (Transformer-less and Inductor-less). ii) Continuous input current iii) Low voltage rating semiconductor devices and capacitors iv) Modularity v) Easy to add a higher number of levels to increase voltage gain vi) Only two control switches with alternating operation and simple control. The proposed converter is compared with recent existing transformer-less and Inductor-less power converter in term of voltage gain, number of devices and cost. The application of proposed circuit is discussed in detail. The proposed converter has been designed with rated power of 60W, input voltage is 24V, output voltage is 100V and switching frequency is 100 kHz. The performance of the converter is verified through experimental and simulation results.

Day by day, the share of renewable energy-based power plants such as offshore wind farms and photovoltaic power plants, in the present-day power systems is escalating. Nevertheless, most of these power-producing facilities have been located quite far away from the load centers. At this stage, HVDC power systems provide satisfactory options due to qualities such as reduced line losses, substantial controllability, and environmental advantages. Nevertheless, unique converter designs are required to combine asynchronous HVDC networks with each other and with already existing high voltage alternating current (HVAC) networks. In this study, based on the above special cases, a unique DC-DC modular multilevel converter (MMC) architecture is presented that provides an excellent solution for both integrating modern asynchronous HVDC networks and integrating these modern HVDC power systems with existing asynchronous HVAC power systems. The mathematical analysis of the recommended DC-DC MMC design has been examined in detail and the power transfer between two asynchronous power grids has been realized in a simulation environment. Efficient bilateral power transmission has been made achievable by the control system. The recommended DC-DC MMC topology has shown to be a highly successful approach, in the interconnection of HVDC power systems, according to the simulation results.

In this paper, the authors consider the influence of the type of power supply and the internal parameters of the DC-DC converter on the stability of the system at constant power load. The stability of the system under consideration is important in the design and development of the power supply system for an autonomous consumer. Such a typical system can be a DC microgrid. In the work, when analyzing the stability of the system, the power source is not considered an ideal voltage source, but the active-inductive nature of the voltage source is taken into account, which is equivalent to using a synchronous machine with permanent magnets. The Rauss-Hurwitz algebraic criterion was used as a criterion for analyzing the stability of the system. This will make it possible to build and analyze the areas and boundaries of the system's stability. As a result, the areas and boundaries of the stability of the system were presented. The general trend towards the behavior of the zone of instability of the system was given. At the same time, dependences describing the boundaries of instability are presented, which are combinations of parameters of the DC-DC converter, beyond which the system becomes unstable. The presented definitions of the instability limits can be used as a corrective device of the control system to ensure the stability of the system in the upper limits of the power consumption.

This paper presents a detailed description of three methodologies to electrify the rural households of small loads with reliable and economical method using solar energy as input source of power. It is observed that high DC voltage is better and economical solution rather than AC based solar systems and low voltage DC systems. In this paper, three methodologies were analysed to select the right combination of portable converters with low prices, which may further enhance the energy access and affordability to common people. The proposed three methodologies were tested through action research in collaboration with a team of scientists and technical experts of National Institute of Solar Energy. The comparative analysis is carried out on three different converters, various kind of house loads and types of power supply i.e. AC/DC. The performance, quality and economic evaluation has been carried out with the help of MATLAB SIMULINK and other measuring instruments specific for solar photovoltaic systems. The derived results were analysed and inferences made for use in village household loads and their income groups. Further, a three-step analytical framework on village-level power energy efficient power at affordable power preposition was presented. This study will help in the designing as well as in the performance and economic evaluation of converters based on solar photovoltaic systems of different technologies.

This article deals with the denoising of signals from sensors (current and voltage) in a photovoltaic conversion chain using wavelet theory. The idea is to reduce the noise as much as possible without distorting or losing the original signal information. To see the reliability of this proposed method, a comparative study between our proposed method (WDD) and the classic low-pass filter method was presented. The contribution in this work is the improvement of the DC-DC boost converter via the use of wavelet theory, however, that’s why we set two objectives: the first is to obtain reliable control of the DC-DC boost converter via the proposed WDD and the second to increase the overall system efficiency. The experimental results show a very great improvement in the quality of the signals of the proposed method compared to the classic method of filtering by low-pass filter.

Recently, solar energy is growing as a power source for potential alternative to meet the global demand. Unlike other energy sources such as coal, nuclear, gas and oil, their prices are not only stable, they prevent the harmful side-effects on the environment, being one of the best sources of clean energy (solar energy). This article presents an analysis of the transformation of the static system for the treatment of solar energy using photovoltaic modules. It is designed to generate energy for future generations to be more useful from different parts of the photovoltaic energy conversion system, such as a DC-DC converter, current inverter, maximum power tracking algorithm (MPPT), filter, the stability of a system, etc. The above result will be useful in the improvement of efficiency in photovoltaics structures.

This paper presents a comprehensive study and the analysis of a topology of a no isolated DC-DC intituled Double Quadratic Boost converter with high static gain. This converter has the main advantage of high static gain and low voltage stress on its switches. The article will first present the theoretical analysis of the converter operating in an open loop. The objective of the work is the mathematical modeling and the control strategy of the converter, as well as the validation through closed-loop experimental results. Besides, we presented the practice test results to demonstrate the operation of the converter, such as the static gain experimental curve, the practice efficiency of the converter, and the control of the output voltage, as well as the capacitor voltage balance control. The authors designed a prototype for 1 kW, with a switching frequency of fs=50kHz, with FPGA-based command and modulation.

Based on the analysis of the working principle, circuit design and working loss of the common charger DC/DC converter, this paper designs a ZVS half-bridge three-level DC/DC converter based on non-phase-shift control mode, and proposes a multi-stage constant current and voltage limiting charging control strategy based on modulation wave selection control. The simulation results show that the proposed method and control strategy have faster voltage regulation ability and wider stability margin, and can achieve stable current sharing control in the charging process.

This paper presents an Application Based Active Learning (ABAL) methodology on Power Electronics (PE) and Electric Machines (EM) as a hybrid laboratory course for the undergraduate students to design and implement the real-world engineering problems. The ABAL is a type of active learning which is a branch of Learner-centered teaching (LCT). The DC/DC converter along with the speed control of DC separately excites the motor. In addition, a DC/AC converter is designed to control the speed of an induction motor. The results are then investigated on a hardware platform under the ABAL experimental methodology. This paper also discusses the problem identification selection of the equipment, circuit design, hardware mounting and critical analysis of the results acquired from the hybrid laboratory. The ABAL methodology was evaluated based on student satisfaction, feedback, grades and interest to solve the real-world problem rather than cramming the engineering concepts and fulfill so-called lab routine and tasks

In this paper, a fuzzy logic-based energy management system and multi-port quasi-z-source converter are proposed that utilizes hybrid renewable energy sources. The system ensures that each energy source module can be used individually by employing fuzzy logic to define power modes. This approach also helps prevent switching losses resulting from extra switching of the source modules. Also, the proposed energy management does not have a mathematical model, so applicability is simple and it is suitable for different multiple input topologies. The Mamdani fuzzy inference system can be designed to capture the nonlinear behavior of the system because of the linguistic rules. Moreover, by adopting the quasi-z-source network to the end of the multi-port converter, the switching losses of the multi-port modules have been significantly reduced. The simulation results are obtained using MATLAB Simulink, and the experimental results are obtained by connecting the circuit to MATLAB Simulink via an Arduino Due.

Driven by the proliferation of DC energy sources and DC end-use devices (e.g., photovoltaics, battery storage, solid-state lighting, and consumer electronics), DC power distribution in buildings has recently emerged as a path to improved efficiency, resilience, and cost savings in the transitioning building sector. Despite these important benefits, there are several technological and market barriers impeding the development of DC distribution, which have kept this technology at the demonstration phase. This paper identifies specific end-use cases for which DC distribution in buildings is viable today. We evaluate their technology and market readiness, as well as their efficiency, cost, and resiliency benefits while addressing implementation barriers. The paper starts with a technology review, followed by a comprehensive market assessment, in which we analyze DC distribution field deployments and their end-use characteristics. We also conduct a survey of DC power and building professionals through on-site visits and phone interviews and summarize lessons learned and recommendations. In addition, the paper includes a novel efficiency analysis, in which we quantify energy savings from DC distribution for different end-use categories. Based on our findings, we present specific adoption pathways for DC in buildings that can be implemented today, and for each pathway we identify challenges and offer recommendations for the research and building community.

The use of different sources to energize a load is convenient in many applications, particularly those where two or more renewable energy sources are employed as: energy harvesting, hybrid vehicles, and off-grid systems. In these cases, a multi-input converter able to admit sources with different characteristics and, if necessary, select the output power of each source. Several topologies of multi-input converters have been proposed to this aim, however, most of them are based on multi-stage designs, which decreases efficiency and increases control complexity, particularly when more than two sources are used. In this work, a three-input step-up converter easy to control in open loop condition is analyzed. A designed procedure is described, and experimental results are presented for a 1 kW power converter. The implemented converter results in a higher voltage gain, less storage element keeping high efficiency compared to similar topologies. Using the procedure here proposed, this converter that was initially proposed for photovoltaic applications is enabled to be used in medium and high-power applications, for example when renewable energy sources are used.

Lead Acid Batteries (LABs) are used for starting, lighting, and igniting, as well as in air conditioning systems and to supply power to electric engines in transport vehicles (TVs). However, the application of LABs for TVs has faced a number of market challenges, mounted by the upcoming high energy density and long lifespan batteries, such as lithium ion. LABs, on the other hand, are inexpensive. The key research question is, how can the lifespan of LABs used in automotive industries be increased, while still ensuring a low cost solution? Thus, integrating LABs with the supercapacitor (known as an electric double layer capacitor—EDLC) is likely to outperform the competing alternative batteries for TVs. This paper proposes a multiple stage approach to hybrid lead acid batteries and a supercapacitor system for TVs that is capable of maintaining the battery state-of-charge (SOC) at statistically high limits, ranging between 90% and 95%. This SOC target will likely ensure that the lifespan of the hybrid battery system can be elongated (extended) more than its competitors. In this study, the multiple stage approach of concatenated converters has been designed in order to satisfy all energy storage requirements for different characteristics of LABs and the supercapacitor. The designed hybrid system has been simulated using Matrix Laboratory (MATLAB/Simulink (version R2016a, MathWorks, Natick, MA, USA)). The simulated results show that high transient currents from the direct current (DC) bus of LABs, caused by the regenerative braking or deceleration of the TVs, reduce the battery lifespan and induce mechanical stress. The supercapacitor reduces the stress on the LAB by absorbing high transient currents. This, in turn, keeps the LABs’ SOC between 90% and 96% and the voltage at 12 V. As indicated by the simulated results, the hybrid battery SOC is maintained at 90–96% and the terminal voltage is approximately 12 V.

Reliable and robust control of power converters is a key issue in the performance of numerous technological devices. In this paper we show a design technique for the control of a DC-DC buck converter with a switching technique that guarantees not only good performance but also global stability. We show that making use of the contraction theorem in the Jordan canonical form of the buck converter, it is possible to find a switching surface that guarantees stability but it is incapable of rejecting load perturbations. To overcome this, we expand the system to include the dynamics of the voltage error and we demonstrate that the same design procedure is not only able to stabilize the system to the desired operation point but also to reject load, input voltage and reference voltage perturbations.

Interference on Power Line Communication (PLC), which is a wired communication technology that provides communication and data transmission over the existing electrical network, is examined in this paper. Many applications employ PLC technologies, which have the benefit of leveraging existing power connections for both power and data transfer, reducing cost and complexity. These interactions may be observed in contemporary smart grids and automobile power networks, where lengthy cables, switching power supplies, and communication links all work together but exacerbate electromagnetic interference problems. This research examines the effects of Spread Spectrum methods used to reduce EMI from power converters on PLC systems. Spread spectrum modulation and its three variants Sine, Random and Triangle are frequently employed to meet the requirements of electromagnetic compatibility, however there are some repercussions, that might be detrimental to the converter or the rest of the electrical network. These outcomes occur for various modulation algorithm settings and at various frequencies. Measurements are made utilising the Frame Error Rate value provided by the PLC link system to ascertain the interference produced by a SiC-based DC-DC converter in order to investigate these concerns and standardise an assessment approach.

This paper presents a comprehensive review that highlights the characteristics of non-isolated step-up converters based on high boost voltage lifting techniques. The paper categorises the high boost techniques: multistage/multilevel, switched capacitor, voltage multiplier, voltage lift, switched inductor, and magnetic coupling. The paper also discusses in detail the advantages and disadvantages for each category such as cost, complexity, power density, reliability and efficiency. The number of passive and active components, voltage gain, voltage stress, switching frequency, efficiency and power rating are also compared. Although the paper considers coupling inductors in the context of the non-isolated converter, the focus of the entire article is on the non-isolated high voltage step-up techniques. The key contribution in this paper is the review of high boosting techniques rather than the DC /DC converters. This allows divergence of new ideas and new power converters that will help provide highly efficient and flexible power converters for several applications where the sending end voltage is very low as photovoltaic systems. In addition, many applications and control techniques of DC/DC converters are summarised in this paper.

The integrated DC-DC converter is appropriate for use in many domains, namely, display, cellular, and portable applications. This paper presents an integrated monolithic voltage-mode DC-DC boost converter with a low-power control circuit. The driver circuit requires an integrated converter to power up a digital logic circuit and converts the unregulated DC input to the controlled DC output at the desired voltage level. It is the integration of both power switches and control circuitry within the same CMOS technology to buck down and boost voltages using a switch mode regulator. In order to increase power efficiency in the DC-DC boost converter that provides low-power operation with a small chip size, a low-voltage operation is applied to the unique circuit characteristic. The operational transconductance amplifier(OTA), comparator, and oscillator in the control circuit are designed with the supply voltage of 3.3V and the operating frequency of 5.5 MHz. A compensator is used to create a pole that has sufficient phase margin for high stability. The DC- DC boost converter is measured in both experiment and simulation. Testing of the proposed circuit on the 0.35μm CMOS process shows that the output transient time of the amplifier can be controlled within of 7μsec and the output voltage is accurately controlled with a ripple ratio of 3%.

A modular switched-capacitor (SC) DC-DC converter (MSCC) is introduced in this paper. It is designed to boost a low input voltage to a high voltage level and can be applied for photovoltaics and electric vehicles. This topology has high extensibility for high voltage gain output. The merits of the converters also lie in the fault tolerance operation and the voltage regulation with a minimum change in the duty ratio. Those features are built in when designing the modules and then integrating these into the DC-DC converter. Converter performance including voltage gain, voltage and current stress are focused and tested. The converter is modelled analytically, and its control algorithm is analyzed in detailed. Both simulation and experiment are carried out to verify the topology under normal operation and fault mode operation.

A high step-up DC-to-DC converter that integrates an isolated transformer and a switched-clamp capacitor is presented in this study. The voltage stress of the main power switch should be clamped to 1/4 V by using the turn ratio and switched-clamp capacitor of an isolated transformer to achieve a high voltage gain. In addition, a passive clamp circuit is employed reduce voltage stress on the main power switch. The energy of the leakage inductor can be recycled by the clamp capacitor because of the passive clamp circuit, thereby improving the power converter efficiency. The converter consists of one isolated transformer, one main switch, three capacitors, and four diodes. Operating principle and steady-state analyses are also discussed. Finally, a 24-V-input voltage to 200-V-output voltage and a 150 W output power prototype converter are fabricated in the laboratory. The maximum efficiency of the converter is 95.1 at 60 W.

In this paper, a buck DC-DC converter with the proposed twin frequency control scheme (TFCS) and accurate load current sensing (ALCS) have been designed and implemented with 0.18µm CMOS technology for a supply voltage ranging from 2.0-3.0V which is compatible with state-of-the-art batteries (NiCd/NiMH: 1.1-2V, Li-Ion: 2.5-4.2V). The proposed converter yields a peak efficiency of about 92.7% with a load current of 30mA. Furthermore, it only occupies a silicon area of 1.3mm2. The proposed buck converter is dedicated for smartphone applications whereby it spends most of its time in idle, low load conditions.

This paper proposes a novel symmetrical active-switched coupled-inductor high-step-up DC/DC converter. A new active-switched coupled inductor is used to allow much higher voltage gain of the proposed converter. The symmetrical circuit structure of the proposed converter evenly divides large input currents and reduce input current ripple by operating in interleaved mode so power density is increased. The switches also have low voltage stress. The operating principle and design considerations for the converter topology are described. The proposed converter with an input voltage of 40 V, an output voltage of 400 V and an output of 1000 W at a switching frequency of 50 kHz is implemented. The simulations and experimental results are thus depicted to verify the theoretical analysis. The highest efficiency is 95.5% at 200 W measured by using a HIOKI 3390. Consequently, the proposed converter is suitable for renewable energy generation systems that require high power, high voltage gain and high efficiency.

Intended for the high voltage gain and wide-range operation of DC/DC converters for photovoltaic energy storage systems, a topology for four-phase interleaved DC/DC converters for photovoltaic power generation is proposed. This topology increases output voltage for output in series, and reduces the input current ripple by paralleling the input. Compared with traditional boost converter topology, the proposed topology reduces the output current and output voltage ripple, reduces the stress of the switching device, and reduces the withstanding voltage of the output capacitor under the premise of ensuring the boost ratio. Experimental results show that the maximum efficiency of the converter reaches 95.37%. Compared with traditional boost converters, the proposed converter offers obvious advantages in efficiency under the conditions that the output voltage and load are variable.

While traditional AC mechanical circuit breakers have been competent for protecting AC circuits, high penetration of DC power distribution technologies like DC microgrids (MGs) obligate better disruption performance features such as quick and reliable switch-ing speeds. However, a DC circuit breaker (DCCB) novel design is challenging due to the need to quickly break high currents within milliseconds, caused by the high fault current rise in DC grids compared to AC grids. In DC grids, the circuit breaker must provide zero current crossing and be designed for absorbing surges since the arc is not naturally extinguished by the system. Additionally, the DC breaker must mitigate the magnetic energy stored in the system inductance and withstand residual over-voltages after current interruption. These challenges require a fundamentally different topology for DCCBs, which are typically made using solid-state semiconductor technology, metal oxide varistors (MOV), and ultra-fast switches. This study aims to provide a comprehensive review on development, design, and performance description of DCCBs in parallel with a specific concentration on analysis of internal topology, energy absorption path and sub-circuits in Solid-State (SS)-based DCCBs. The research explores various novel designs that introduce different structures for energy dissipation solution. The classification of these designs is based on the fundamental principles of surge mitigation and a detailed analysis of the techniques employed in DCCBs. In addition, our framework offers an advantageous reference point for the future evolution of SS-circuit breakers in numerous developing power delivery systems.

Fully sustainable hydrogen production demands renewable energy sources. This study uses an approach that combines solar photovoltaic (PV) systems with minimal batteries to tailor the energy supply to the unique demands of anion exchange membrane (AEM) electrolyzers. An open source DC-DC adjustable converter is designed, prototyped, and tested to enable an AEM to operate at its optimum efficiency without disrupting the continuous operation of existing loads. A structured operating schedule is simulated to align PV performance with AEM electrolyzer characteristics. The results show the >90% efficiency open-source converter was able to directly power the electrolyzer while taking advantage of solar energy surplus for hydrogen production. By strategically scheduling the electrolyzer to maximize output and minimize waste the system only utilizes excess solar energy. By employing this sustainable method, the study highlights a scalable solution that not only enhances the efficiency of hydrogen production, but also promotes the deployment of PV.

This paper proposes a circuit model of Cross-Coupled CMOS AC – DC Charge Pump (XC – CP) operating in subthreshold region. The aim is improving the efficiency to design XC – CPs with variety of specifications, e.g., input and output voltages and AC input frequency. First, it is shown that the output resistance (Ro) of XC – CP is much higher than those of CPs with single diodes (SD – CP) and ultra-low-power diodes (ULPD – CP) as charge transfer switches (CTSs). Second, the reason behind the above feature of XC – CP is identified by a simple model that the gate-to-source voltages of CTS MOSFETs are independent of the output voltage of the CP. Third, high but finite Ro of XC – CP is explainable with a more accurate model that includes the dependence of the saturation current of MOSFETs operating in subthreshold region on the drain-to-source voltage which is a function of the output voltage of CP. The model was in good agreement with measured and simulated results of XC – , SD – and ULPD – CPs fabricated in 250 nm CMOS.

The concepts of fractional calculus and the related techniques have been gaining momentum in circuit system fields, and an increasing body of evidence suggests that fractional-order characteristics are widely distributed in electronic components. In this paper, we consider the fractional characteristics of non-solid aluminum electrolytic capacitors and focus on the nonlinear dynamic characteristics of peak-current-mode controlled (PCMC) dc-dc boost converters with such components. In the work, we establish a piecewise smooth non-commensurate fractional-order model to describe the converter, in which the fractional-order equivalent impedance model of capacitors is adopted and the detailed control loop is considered. In order to analyze the converter, we use the fractional Adams-Bashforth-Moulton typed method (F-ABM) and stroboscopic map technique to obtain the time-domain solutions and the bifurcation diagram. The results of bifurcation diagrams indicate that, with the change of different parameters, the converter enters chaotic state through period doubling bifurcation. In order to provide empirical evidence for the nonlinear dynamic analysis, we consider both circuit-level simulation and experiments in the work, the results of which further confirm the results of theoretical analysis.

Microgrids offer flexibility in power generation in a way of using multiple renewable energy sources. In the past few years, microgrids become a very active research area in terms of design and control strategies. Most of the microgrids use DC/DC converters to connect renewable energy sources to the load. In this paper, the simulation model of a DC microgrid with three different energy sources (Lithium-ion battery (LIB), photovoltaic (PV) array, and fuel cell) and external variant power load is built with MATLAB/Simulink and the simulative results show that the stability of DC microgrid can be guaranteed by the proposed maximum power point controller MPPT. The three energy sources are connected to the load through DC/DC converters, one for each. This type of topology ensures protection for each energy source as well as optimum stability at the load.

The concept of DC power distribution has gained interest within the research community in the past years; especially due to rapid prevalence of solar PVs as a tool for distributed generation in DC microgrids. Various efficiency analyses have been presented for the DC distribution paradigm, in comparison to the AC counterpart, considering a variety of scenarios. However, even after a number of such comparative efficiency studies, there seems to be a disparity in the results of research efforts - wherein a definite verdict is still unavailable: 'Is DC distribution a more efficient choice as compared to the conventional AC system?' A final verdict is absent primarily due to conflicting results. In this regard, system modeling and the assumptions made in different studies play a significant role in affecting the results of the study. The current paper is an attempt to critically observe the modeling and assumptions used in the efficiency studies related to the DC distribution system. Several research efforts will be analyzed for their approach towards the system upon which they have performed efficiency studies. Subsequently, the paper aims to propose a model that may alleviate the shortcomings in earlier research efforts and be able to give a definite verdict regarding the comparative efficiency of DC and AC networks for residential power distribution.

This paper aims at presenting an energy management strategy (EMS) based upon optimal control theory for a battery-supercapacitor hybrid power system. The hybrid power system consists of a Lithium-ion battery and a supercapacitor with associated bidirectional DC/DC converters. The proposed EMS aims at computing adaptive gains using salp swarm algorithm and load following control technique to assign the power reference for both the supercapacitor and the battery while achieving optimal performance and stable voltage. The DC-DC converter model is derived utilizing the first-principles method and compute the required gains to achieve the desired power. The fact that the developed algorithm takes disturbances into account increases the power ele-ments’ life expectancies and supplies the power system with the required power

This Paper delves into a thorough analysis of the DC-DC buck converter tailored for renewable energy applications. Given the prevalent utilization of renewable resources producing DC voltages, this converter plays a pivotal role in stepping down high-level DC voltages to more manageable levels. The research focuses on varying the duty cycle to assess its impact on the converter's output voltage performance. Simulations conducted using PSIM are meticulously compared with hardware implementation results, demonstrating the converter's efficacy in generating significantly reduced output voltages. The findings underscore the practical applicability of this converter in renewable energy scenarios, offering a succinct yet insightful perspective on its performance and adaptability.

Here we present calculation of the critical current of DC SQUID based on the Josephson junction on multi-band superconductor with frustration effect. It is shown that the changing of the critical current of DC SQUID with small geometrical inductance is determined by the ratio of supercurrent amplitude in different channels and the external magnetic field. In the a case of DC SQUID with high inductance frustration effects can be ignored.

Background Successful treatment for patients with metastatic colorectal cancer who failed to response to first-line treatment has been a challenge due to their low response rate for later-line treatment and poor progression free survival and overall survival. The application of dendritic cell-cytokine-induced killer cells (DC-CIK) immunotherapy combined with conventional treat-ment, either surgical resection or chemotherapy, showed improvement in survivals in first-line treatment for metastatic colorectal cancer. In this retrospective study, we aimed to evaluate the benefit of dendritic cell-cytokine-induced killer cells (DC-CIK) immunotherapy for patient with refractory metastatic colorectal cancer. Methods A total of 20 patients with refractory metastatic colorectal cancer receiving cell-cytokine-induced killer cells (DC-CIK) immunotherapy were enrolled to this study. Among these patients, 11 patients responded to the treatment and the remaining 9 patients did not. All patients were followed for at least one years and the determination of treatment response was mainly based on image study at 6 months after the completion of treatment. Data were analyzed with Kaplan-Meier method and log-rank test. Results The treatment response rate of the study group is 55% (11/20). The median progression free sur-vival (PFS) and median overall survival (OS) of responsive patients was 7 months and 12 months, respectively. The median overall survival of irresponsive patients was 9.5 months. Four responsive patients received subsequent metastectomy or cytoreduction plus hyperthermic in-traperitoneal chemotherapy surgery (CRS + HIPEC). Conclusion DC-CIK cell-based immunotherapy may provide benefits for patients with refractory mCRC with improved response rate and progression free survival.

This paper presents a new high-efficiency-high-step-up based converter integrating two stype DC-DC Boost and Flyback coupled magnetic converter with recovery stage dedicated to smart HVDC distributed architecture in renewable energy production systems. Appropriate duty cycle ratio assumes that the recovery stage work with parallel charge and discharge to achieve high step-up voltage gain. Besides, the voltage stress on the main switch is reduced with a passive clamp circuit and thus, low on-state resistance Rdson of the main switch can be adopted to reduce conduction losses. The circuit is simple to control. As a final point of this research, the simulation and the prototype investigational results are presented to demonstrate the effectiveness of this proposed converter.

(1) Background: After the discovery and application of Chlamydomonas reinhardtii channelrhodopsins, the optogenetic toolbox has been greatly expanded with engineered and newly discovered natural channelrhodopsins. However, channelrhodopsins of higher Ca2+ conductance or more specific ion permeability are still in demand. (2) Methods: In this study, we mutated the conserved aspartate of the transmembrane helix 4 (TM4) within Chronos (Stigeoclonium helveticum channelrhodopsin = ShChR) and PsChR (Platymonas subcordiformis channelrhodopsin) and compared them with published ChR2 (C. reinhardtii channelrhodopsin-2) aspartate mutants. (3) Results: We found that the ChR2 D156H mutant (XXM) showed enhanced Na+ and Ca2+ conductance, which was not noticed before, while the D156C mutation (XXL) influenced the Na+ and Ca2+ conductance only slightly. Furthermore, the D173H mutant of PsChR showed a much improved photocurrent, compared to wildtype, and even higher Na+ selectivity to H+ than XXM. PsChR D173H also showed a strongly enhanced Ca2+ conductance, more than 2-fold that of the calcium translocating L132C of ChR2 (CatCh). (4) Conclusions: We found that mutating the aspartate of the TM4 to histidine influences the ion selectivity of channelrhodopsins. With the large photocurrent and enhanced Na+ selectivity and Ca2+ conductance, XXM and PsChR D139H are promising powerful optogenetic tools, especially for Ca2+ manipulation.

In this paper, the design and performance investigation of the permanent magnet machines have been done to increase the mechanical and electrical outputs improvement of the systems. A permanent magnet Dc motor (PMDM) and generator (PMDG) have been modelled and designed to improve the angular position and generated current respectively. In this work, augmentation based H 2 optimal and H infinity synthesis controllers have been designed as a controller for the two systems and a comparison between the proposed controller for tracking a reference inputs and a promising results have been obtained.

This research article aims to present implementation and evaluation of the HPPT design based on using multi-parallel pumps switching for yielding performance with reference to potential change of daily irradiance. After that, the curve fitting of the hydraulic performance scenarios is tested to compare the hydraulic energy growth behaviors with reference to exponential and power growth models.

This paper provides a new management method (MM) to optimally operate standalone direct current (DC) photovoltaic water pumping system (PVWPS) and synchronize its hydraulic performance to variable daily irradiance. The proposed approach well considers the issues from PV generator and a positive displacement pump mismatching to deserve a hydraulic network. Accordingly, Management Method uses small pumps mounted in parallel scheme to displace the hydraulic power point (HPP) in order to satisfy the mal adequacy between supply and load. Based on experimental Study; this approach showed a yielded standalone system, possibility of running pumping system using only photovoltaic supply (Without use of capacitance), and possibility to design more economical PV systems as the maximum peak power demand for each month can be satisfied using small power pumps in parallel and adjusting their switch with accordance to varying daily irradiance. Moreover, an analytical model was developed with reference to the obtained experimental results. This model based on a daily occurring irradiance as inputs in order to predict optimal performance outputs. It can be considered as a decision tool to track power point resulting from optimal electrical and hydraulic performances of the pumping system according to changes of the daily irradiance.

Herein, we present the design technique of a resonant rectifier for piezoelectric (PE) energy harvesting. We propose two diode equivalents to reduce the voltage drop in the rectifier operation, a minuscule-drop-diode equivalent (MDDE) and a low-drop-diode equivalent (LDDE). The diode equivalents are embedded in resonant rectifier integrated circuits (ICs), which use symmetric bias-flip to reduce the power wasted for charging and discharging the internal capacitance of a PE transducer. The self-startup function is supported by synchronously generating control pulses for the bias-flip from the PE transducer. Two resonant rectifier ICs, using both MDDE and LDDE, are fabricated in a 0.18 μm CMOS process and their performances are characterized under external and self-power conditions. Under the external-power condition, the rectifier using LDDE delivers an output power POUT of 564 μW and a rectifier output voltage VRECT of 3.36 V with a power conversion efficiency (PCE) of 90.1%. Under self-power conditions, the rectifier using MDDE delivers a POUT of 288 μW and a VRECT of 2.4 V with a corresponding PCE of 74.6%. The result shows that the power extraction capability of the proposed rectifier is 5.9 and 3.0 times higher than that of a conventional full-bridge rectifier.

Ensuring a protection scheme in DC distribution is more difficult to achieve against pole-to-ground fault than in AC distribution system because of the absence of zero crossing points and low line impedance. To complement the major obstacle of limiting the fault current, several compositions have been proposed related to mechanical switching and solid-state switching. Among them, solid-state circuit breakers(SSCBs) are considered a possible solution to limit fast fault current. However, they may cause problems in circuit complexity, reliability and cost-related troubles due to the use of multiple power semiconductor devices and additional circuit configuration to commutate current. This paper proposes the SSCB with a coupled inductor(SSCB-CI) which has symmetrical configuration. The circuit is comprised of passive components like commutation capacitors, a CI and damping resistors. Thus, proposed SSCB-CI offers the advantages of simple circuit configuration and fewer utilized power semiconductor devices than another typical SSCBs in LVDC microgrid. For analysis, six operation states are described for the voltage across main switches and fault current. The effectiveness of the SSCB-CI against a short-circuit fault is proved via simulation and experimental results in a lab-scale prototype.

Background: Student-specific stress is pervasive and impairs health and attainment. Experimentally induced self-affirmation can reduce stress, but little is known about the mechanisms underlying this effect, and the role of individual differences. The present study explores the relationship between spontaneous self-affirmation, student-specific stress, and overlapping constructs of positive self-regard during the COVID-19 pandemic. Methods: The study investigated inter-relationships between spontaneous self-affirmation, student-specific perceived stress and potential covariates including self-esteem, self-integrity and habitual positive self-thought. University students (N = 151) aged 18 to 50 responded to an online questionnaire including the Spontaneous Self-Affirmation Measure, College Student Stress Scale, Rosenberg Self-Esteem Scale, Habitual Index of Positive Thinking and Self-Integrity Scale. Results: Unexpectedly, regression analysis revealed that spontaneous self-affirmation was a positive predictor of student-specific stress, seemingly driven by relational affirmations. Self-esteem and habitual self-thought were negative predictors of student-specific stress, whilst self-integrity was not a predictor. Conclusions: Habitual positive self-thought may offer a sustainable solution to student-specific stress, but spontaneous self-affirmation does not. A reduction in defensive responses, elicitation of negative emotions, or use of conditional relationships in relational affirmation

DC residential distribution system (RDS) consisted by DC living home will be a significant integral part in the future green transmission. Meanwhile, the increasing number of distributed resources and intelligent devices will change the power flow between main grid and demand sides. The utilization of distributed generations (DGs) requires an economic operation, stability, environmentally friendly in the whole DC system. This paper not only presents an optimization schedule and transactive energy (TE) approach through centralized energy management system (CEMS), but a control approach to implement and ensure DG output voltages to various DC buses in DC RDS. Based on data collection, prediction and a certain objection, the expert system in CEMS can work out the optimization schedule, after this, the voltage droop control for steady voltage is aligned with the command of unit power schedule. In this work, a DC RDS is as a case study to demonstrate the process, the RDS is associated with unit economic models, cost minimization objective is proposed to achieve based on real-time electrical price. The results show that the proposed framework and methods will help the targeted DC residential system to reduce the total cost and reach stability and efficiency.

The diffusion of electric vehicles (EVs) can be sustained by the presence of integrated solutions offering parking and clean power supply. The recourse to DC systems allows to better integrate EV bidirectional energy exchange, photovoltaic panels and energy storage. In this paper, a methodology for optimal techno-economic sizing of a DC-microgrid for covering EV mobility needs is carried out. It is based on the definition of different scenarios of operation, according to typical EV usage outlooks and environmental conditions. In each scenario, optimal operation is carried out by means of a specific approach for EV commitment on different stations. The sizing procedure is able to handle the modular structure of microgrid devices. The proposed approach is applied to a case study of envisaged EV service fleet for Bari port authority.

In this paper I tentatively answer 50 questions sampled from a pool of over 10,000 weekly questions formulated by students in a course entitled “The Self”. The questions pertain to various key topics about self-processes, such as self-awareness, self-knowledge, self-regulation, self-talk, self-esteem, and self-regulation. The students’ weekly questions and their answers highlight what is currently know about the self. Answers to the student questions also allow for the identification of some recurrent lessons about the self. Some of these lessons include: all self-processes are interconnected (e.g., prospection depends on autobiography), self-terms must be properly defined (e.g., self-rumination and worry are not the same), inner speech plays an important role in self-processes, controversies are numerous (are animals self-aware?), measurement issues abound (e.g., self-reflection as an operationalization of self-awareness), deficits in some self-processes can have devastating effects (e.g., self-regulatory deficits may lead to financial problems), and there are lots of unknowns about the self (e.g., gender differences in Theory-of-Mind).

This research proposes a roof-mounted auxiliary power supply (APS) system for 600VDC low-floor light rail vehicle (LRV). The proposed APS system consists of five parallel-connected dc-ac inverter modules (modules 1-5). The inverter modules 1 and 2 are three-phase dc-ac inverters for compressor motors of the cooling system, and the inverter modules 3 and 4 are three-phase dc-ac inverters for air pump motors of the braking system. The inverter module 5 is single-phase dc-ac inverter for 220VAC power supply for onboard electric loads. Simulations and experiments were carried out under variable load torque and output frequency for modules 1 – 4; and under full and no resistive loads for the inverter module 5. The measured total input current and total input power of the proposed APS system under full load condition are 118.76A and 71.25kW. Essentially, the proposed APS system is operationally applicable to the 600VDC low-floor RLV. Besides, the novelty of this research lies in the use of five parallel-connected inverter modules, unlike in the conventional APS systems which require three-phase output transformer or isolated dc-dc converter. Specifically, the proposed APS system requires neither three-phase output transformer nor isolated dc-dc converter.

Vitrimers are covalent network materials, comparable in structure to classical thermosets. Unlike normal thermosets, they possess a chemical bond swap mechanism that makes their structure dynamic and suitable for activated welding and even autonomous self-healing. The central question in designing such materials is the trade-off between autonomy and material stability: The swap mechanism facilitates the healing but it also facilitates creep, which makes the perfectly stable self-healing solid a hard goal to reach. Here, we address this question for the case of self-healing vitrimers made from star polymers. Using coarse-grained molecular dynamics simulations, we study the adhesion of two vitrimer samples and find that they bond together on timescales that are much shorter than the stress relaxation time. We show that the swap mechanism allows the star polymers to diffuse through the material through coordinated swap events, but the healing process is much faster and does not depend on this mobility.

With the rapid development of electric vehicles, the infrastructure for charging stations is also expanding quickly, and the failure rate of charging piles is increasing. To address the effective operation and maintenance of charging stations, a method based on the XGBoost algorithm for electric vehicle DC charging stations is proposed. An operation and maintenance system is con-structed based on state analysis, considering the operation status of the charging station and users' charging habits. Factors such as driving and charging habits, road traffic, and charging station equipment are taken into account. The training sample data is established using historical data, online monitoring data, and external environmental data, and the charging station status evaluation model is trained using the XGBoost algorithm. Based on the condition assessment results, a risk assessment model is established in combination with fault parameters. Risk tracking of the charging station is conducted using the lack of power supply (ENC), evaluating the risk level of each station, and determining the operation and maintenance order. The optimal opera-tion and maintenance model for DC charging stations, aimed at achieving both economic and reliable goals, is constructed to determine the operation and maintenance schedule for each sta-tion. The results of the case study demonstrate that the state evaluation and operation and maintenance strategy can significantly improve the reliability of the system and the overall ben-efits of operation and maintenance while meeting the required standards.

Regenerative braking energy (RBE) recovery of trains can improve energy efficiency as well as reduce the overall greenhouse gases emissions of electric rail systems. The train's speed limit, track elevation, track curvature, and headway time can affect the amount of RBE recovered. This study aims to investigate the impacts of these parameters on the RBE recovery for a DC third rail system. A DC third rail system has been modeled using the ETAP-eTraX software based on the Malaysia Mass Rapid Transit Line 2 (MRT Line 2) traction power system. The effects of the change of speed limit, track elevation, track curvature, and headway time of the trains on the RBE recovery have been evaluated under various scenarios. The results showed that the track’s elevation has the most significant influence on the overall energy consumptions of the train while the speed limit has the most significant influence on the amount of RBE recovery.

This work involves results of research on short-term and long-term DC-drifts in electro-optical modulators based on annealed proton exchange waveguides in LiNbO3 crystals after wafer pre-annealing. The relaxation time of the DC-drift of the operating point for a short-term drift is minutes, and for a long-term drift, hours and days. DC-drift was measured by applying bias voltage and changing crystal temperature. Obtained results shows significant impact on stability of operating point in EO-modulators after treatment of defective structure of the near-surface layer of a LiNbO3 crystal. Treatment of the disturbed near-surface layer of a LiNbO3 crystal results in twice reduction of short-term DC-drift and increase of operation stability of electro-optical modulators during long-term measurement of temperature by activation energy calculation.

Photovoltaic (PV) systems, which are renewable energy sources, are increasingly being utilized in distributed generation. To maintain a stable energy balance, energy storage systems such as batteries (BAT) play a vital role. Electric vehicles (EVs) offer a promising solution with rechargeable battery systems for operation. The BATs must maintain their state of charge within design boundaries, despite intermittent PV and load power fluctuations, and advanced power control and management techniques are essential for their effective operation. The article evaluates an intelligent controller that uses a Sliding Mode Control adaptive deep learning algorithm Convolutional Neural Networks (SMC-CNN) and a unique Strategy for managing supervisory power. (SPMS) for photovoltaic systems with battery energy storage for better regulation of DC bus voltage. SMC-CNN offers exceptional resilience and seamless functionality, minimizing fluctuations in DC bus voltage in the control strategy design requirements. The primary goals are maintaining a consistent power supply and ensuring continuous service by preventing system components from exceeding capacity. This study aims to enhance the control of DC bus voltage in the PV and battery system, with the primary significance focusing on the following aspects. The advanced SPMS has been created, incorporating control system constraints to enhance SOC balancing speed and reduce fluctuations in DC bus voltage. Power flow management involves optimizing energy flow between the PV system, battery system, and load while minimizing battery capacity requirements. The proposed SMC-CNN and SPMS are demonstrated through real-time simulation using Matlab/Simulink, as demonstrated in comprehensive case studies.

This paper presents two control design strategies for voltage regulation in a single inductor dual output (SIDO) DC-DC Buck converter system. Based on a nominal multiple input multiple output (MIMO) plant model and performance requirements, both an LQR and a decoupled PI control laws are designed to control the power converter system, under parametric uncertainties such as voltage source variation, CPL power variation, and load resistance variation. Therefore, the SIDO converter can cascade operating, which may cause the undesired effects of voltage oscillation and reduce the system's stability margin. The control performance was assessed under both uncertainties resistive loading and power variation of a constant power load (CPL). A SIDO DC-DC Buck converter board has been developed for experimental tests. The experimental results show that the LQR strategy, compared to the PI strategy, presented a robust performance in the presence of parametric uncertainties in the resistive loads being, however, sensitive to uncertainties due to the presence of CPL loads.

Self-assembly is a spontaneous process through which macroscopic structures are formed from basic microscopic constituents (e.g. molecules or colloids). By contrast, the formation of large biological molecules inside the cell (such as proteins or nucleic acids) is a process more akin to self-organization than to self-assembly, as it requires a constant supply of external energy. Recent studies have tried to merge self-assembly with self-organization by analyzing the assembly of self-propelled (or active) colloid-like particles whose motion is driven by a permanent source of energy. Here we present evidence that points to the fact that self-propulsion considerably enhances the assembly of polymers: self-propelled molecules are found to assemble into polymer-like structures, the average length of which increases towards a maximum as the self-propulsion force increases. Beyond this maximum, the average polymer length decreases due to the competition between bonding energy and disruptive forces that result from collisions. The assembly of active molecules might have promoted the formation of large pre-biotic polymers that could be the precursors of the informational polymers we observe nowadays.

The electric vehicle (EV) industry is experiencing rapid growth, accompanied by continuous advancements in charging infrastructure to satisfy the rising need for fast and reliable charging. Particularly, the focus has shifted towards EV fast charging (EVFC) and its impact on the power grid. This paper presents a comprehensive analysis and survey of scholarly literature and projects conducted in this field over the past decade. The findings highlight the rising demand for EVFC and the need to address its potential adverse effects on the power grid. However, there is a noticeable lack of clear research guidance regarding charging time. To tackle these challenges and pave the way for future solutions, extensive research on DC fast charging, ultra-fast charging, and the integration of vehicle-to-grid (V2G) systems is required. This review paper thoroughly investigates the development of fast charging technology for electric vehicles (EVs), including its advantages and comparative analyses from various perspectives. Furthermore, it delves into the advancements in DC fast charging infrastructure, emphasizing charging standards and control modes. The study also investigates different categories of battery chargers for both on-board and off-board charging. Additionally, it explores the classification of DC-DC converters in the context of DC fast charging stations, discusses control strategies for EV systems, identifies existing challenges, and outlines future trends in EV fast charging.

To achieve a fast testing on barrier properties of organic coatings, immersion test, AC-DC-AC test, and coupled test of AC-DC-AC with hydrostatic pressure were conducted in seawater for a glass flake epoxy coating. Electrochemical impedance spectroscopy (EIS) was used to characterize the degradation processes of the coating during the tests, and the surface of the coating was analyzed using optical microscope, scanning electron microscope (SEM) and Fourier transform infrared spectrometer (FTIR). The results show that the periodically cathodic polarization coupled with high hydrostatic pressure can accelerate the degradation of the coating by facilitating the diffusion and uptake of electrolyte and the delamination of the coating. The coupled test method has the largest acceleration due to the synergetic effect of AC-DC-AC and hydrostatic pressure.

A scientific consensus is emerging on the benefits of dc distribution in medium voltage power systems of ships and cities. At least 50% space savings and increased power transfer capacity are estimated with enhanced voltage dc operation of electric cables. The goal of this research is to contribute to developing the empirical knowledge on the insulation performance in order to validate the feasibility of such anticipated gains of dc versus ac, and to determine the comparative impact of different operational conditions from a component engineering point of view. The partial discharge (PD) activity in cables is measured under ac and dc conditions as an indicator of insulation performance. Specifically, PDs in defects at the semicon-insulation interface are studied in terms of inception voltage, repetition rate and discharge magnitude. Empirical understanding is drawn for operating voltage and frequency dependence of the discharge behavior in such voids in the range of 10 to 20\,kV and 0 to 0.1\,Hz, respectively. The change in PD activity with void evolution is explored.

Of all the renewable energy sources, solar photovoltaic (PV) power is estimated to be a popular source due to several advantages such as its free availability, absence of rotating parts, integration to building such as rooftops, and less maintenance cost. The nonlinear current-voltage (I–V) characteristics and power generated from a PV array primarily depend on solar insolation/irradiation and panel temperature. The extracted PV output power is influenced by the accuracy with which the nonlinear power–voltage (P–V) characteristic curve is traced by the maximum power point tracking (MPPT) controller. In this paper, a bio-inspired roach infestation optimization (RIO) algorithm is proposed to extract the maximum power from the PV system (PVS). To validate the usefulness of the RIO MPPT algorithm, MATLAB/Simulink simulations are performed under varying environmental conditions, for example, step changes in solar irradiance, and partial shading of the PV array. Furthermore, the search performance of the RIO algorithm is examined on different unconstrained benchmark functions, and it is that realized that the RIO algorithm has improved convergence characteristics in terms of finding the optimal solution than Particle swarm optimization (PSO). The results demonstrated that the RIO-based MPPT performs remarkably in tracking with high accuracy as the PSO-based MPPT.

This paper presents a microgrid distributed energy resources (DERs) for a rural standalone system. It is made up of solar photovoltaic (solar PV) system, battery energy storage system (BESS), and wind turbine coupled to permanent magnet synchronous generator (WT-PMSG). The DERs are controlled by maximum power point tracking (MPPT) based proportional intergral (PI) controllers for both maximum power tracking and error feedback compensation. The MPPT uses the perturb and observe (P&O) algorithm for tracking the maximum power point of the DERs. The PI gains are tuned using the Ziegler-Nichol’s method. The developed system was built and simulated in MATLAB/Simulink under two conditions - constant load, and step load changes. The controllers enabled the BESS to charge even during conditions of varying load and other environmental factors such as change of irradiance and wind speed. The reference was tracked very well by the output voltage of the DC grid. This is a useful research for electrifying the rural islanded areas, too far from the grid.

I propose a test for machine self-awareness inspired by the Turing test. My test is simple, and it provides an objective, empirical metric to rectify the ungrounded speculation surging through industry, academia, and social media. Drawing from a breadth of philosophical literature, I argue the test captures the essence of self-awareness, rather than some postulated correlate or ancillary quality. To begin, the concept of self-awareness is clearly demarcated from related concepts like consciousness, agency, and free will. Next, I propose a model called the Nesting Doll of Self-Awareness and discuss its relevance for intelligent beings. Then, the test is presented in its full generality, applicable to any machine system. I show how to apply the test to Large Language Models and conduct experiments on popular open and closed source LLMs, obtaining reproducible results that suggest a lack of self-awareness. The implications of machine self-awareness are discussed in relation to questions about meaning and true understanding. Finally, some next steps are outlined for studying self-awareness in machines.

The present paper reports an exact approach quantifying the electromagnetic contribution to the anomalous magnetic moment occurring in isolated system comprised of non-composite particle carrying elementary electric charge. Essential averaging procedure and regularization of the electromagnetic field potentials necessary when quantifying the electromagnetic self-interactions and when deriving equations of motion without singularities and obeying the conservation laws are thoroughly discussed. The study shows that the dynamics of the considered system is associated to unique classical transcendental equations of motion satisfied by the particle's velocity and the electromagnetic contribution to the anomalous $g$-factor known from the quantum electrodynamics. The equations of motion lead to an exact analytical expression for the anomalous $g$-factor that provides more accurate result than that calculated with the aid of quantum electrodynamics. It matches the experimentally measured value reported in the literature to a one part per trillion. We obtain a_e=0.00115965218000(65) thus reveling the potential of non-perturbative, non-probability methods in predicting the electron's anomalous g-factor.

Background: The adoption of self-care behaviors among patients with arterial hypertension (AH) plays an important role in the management of their health condition. However, a lack of scales assessing self-care is observed. We aimed to develop and validate the Hippocratic hypertension self-care scale. Methods: From a pool of questions derived from a literature review, 18 items were included in the scale and reviewed by a committee of experts. Participants indicate the frequency at which they follow the self-behavior prescribed in each statement on a five-point Likert scale. Data were collected between April 2019 and December 2019. Re-sults: 202 consecutive adult patients with AH were enrolled in the study. The internal consistency of the scale was found to be 0.807, using Cronbach’s alpha coefficient. An exploratory factor analysis identified two do-mains that accounted for 92.94% of the variance of the scale items; however, each sub-scale could not be used as an independent scale. Finally, the test- retest of the scale showed a significant strong correlation (r=0.0095, p<0.001). Conclusion: Our data indicate that the scale is a reliable and valid tool for assessing self-behaviors in patients with AH. Health professionals can use it in their clinical practice to improve the management of patients’ health condition.

: BACKGROUND: The prevalence of smoking among students is a growing concern, particular-ly among medical students. Being associated with stress, competitiveness, and various social in-fluences, smoking can have detrimental effects on self-esteem and self-efficacy and may create a vicious cycle that may contribute to students’ well-being and academic performance out-comes.METHODS: A cross-sectional study on 456 medical students was conducted via an online survey using structured questionnaires on socio-demographic characteristics, smoking habits, nicotine dependence, self-esteem, and self-efficacy. RESULTS: The prevalence of smoking was 31.1% The scores of self-esteem and self-efficacy were positively correlated with smoking habits (W1=0.957, W2=0.975, P<0.05). Students presented rather low smoking addiction with male stu-dents having slightly higher scores than female students on self-esteem and self-efficacy, mili-tary students had higher self-esteem scores than civilians with physical activity having a posi-tive correlation with non-smoking behavior. CONCLUSION: According to our results, self-esteem and self-efficacy were slightly positively correlated with smoking habits. Furthermore, there was no statistically significant association between other social factors and smoking. Our results may develop a theoretical basis for medical students’ psychological variables studying for further implementation of university educational programs and preventive interventions em-powering students towards an overall better quality of life, addressing, among others, smoking behaviors.

Self-enhancement (SE) is often overlooked as a fundamental cognitive ability mediated via the Pre-Frontal Cortex (PFC). Here we present research that establishes the relationship between the PFC, SE, and the potential evolved beneficial mechanisms. Specifically, we believe there is now enough evidence to speculate that SE exists to provide significant benefits and should be considered a normal aspect of the self. Whatever the metabolic or social cost, the upside of SE is great enough that it is a core and fundamental psychological construct. Furthermore, though entirely theoretical, we suggest that a critical reason the PFC has evolved so significantly in Homo sapien is to, in part, sustain SE. We therefore elaborate as to its proximate and ultimate mechanisms.

While the desire to uncover the neural correlates of consciousness has taken numerous directions, self-face recognition has been a constant in attempts to isolate aspects of self-awareness. The neuroimaging revolution of the 1990’s bought about systematic attempts to isolate the underlying neural basis self-face recognition. These studies, including some of the first fMRI (functional Magnetic Resonance Imaging) studies, revealed a right hemisphere bias for self-face recognition in a diverse set of regions including the insula, the Dorsal Frontal Lobe, the Temporal Parietal Junction and Medial Temporal Cortex. Confirmation of these data (which are correlational) was provided by TMS (Transcranial Magnetic Stimulation) and patients in which direct inhibition or ablation of right hemisphere regions leads to a disruption or absence of self-face recognition. These data are consistent with a number of theories including a right hemisphere dominance for self-awareness and/or a right hemisphere specialization for identifying significant social relationships including to oneself.

Fatigue performance and self-repairing activity of asphalt binders are two properties that highly influence the fatigue cracking response of asphalt pavement. There are still numerous gaps of knowledge to fill linked with these two characteristics. For instance, current parameters fail to fully accommodate these two bitumen phenomena. This study aims to propose a new procedure to address this issue utilizing the linear amplitude sweep (LAS) test, LAS with rest period (RP) (LASH) test, and simplified viscoelastic continuum damage (S-VECD) model. This research work used four different types of asphalt binders: neat asphalt (NA), self-healing thermoplastic polyurethane (STPU)-modified bitumen (STPB), self-healing poly (dimethyl siloxane) crosslinked with urea bond (IPA1w)-modified bitumen (IPAB), and styrene–butadiene–styrene (SBS)-modified bitumen (SBSB). Before the testing process, all the materials were subjected to short-term and long-term aging. The new procedure showed a superior capacity to analyze and accommodate all bitumen fatigue performances and self-repairing activities compared to the current method. Another finding proved that asphalt binders with higher self-restoration behavior failed to show better fatigue performance. A breakthrough finding demonstrated that asphalt binder fatigue response augmented when the RP was applied at a higher damage intensity (S) value. STPBs and IPABs reached their highest increments of fatigue response, containing 1.0% of STPU and 0.5% of IPA1w, respectively. Those augmentations were 207.54% and 232.64%, respectively.

This article reviews recent innovations in piezoelectric actuators, then indicates the future research targets. In the materials, the piezoelectric performances of relaxor-lead titanate (PZN-PT, PMN-PT) single crystals have been improved significantly by an AC electric poling technique. Also new loss characterization techniques facilitate developing high-power density piezoelectrics. The RMS vibration velocity reaches 0.6 m/s in the k₃₁ mode in lead zirconate titanate (PZT) nowadays, which corresponds to power density 30 W/cm³. Pb-free materials are urged due to the recent political regulation on toxic materials. In device designs, the original multilayer actuators (MLA) with Ag/Pd electrode have been switched to the ones with Cu or pure Ag, in order to suppress the heat generation, then to enhance the device power density. Piezoelectric micro-electro-mechanical-systems (MEMS’s) started to utilize the <1 0 0> oriented epitaxial films of rhombohedral PZT compositions, which exhibits enhanced piezoelectric properties. Also for higher-power applications, aero-sol deposition (AD) methods have been introduced to 10 -thick films. Regarding drive/control techniques in piezo-actuators, three developments are on-going, that is, “negative capacitance” power supplies for driving off-resonance (pseudo-DC) piezo-actuators, capacitive AC power supplies for efficiently driving resonance piezo-actuators, and DC/DC converters for harvesting electric energy from high-impedance piezoelectric devices under noise vibration. The applications of piezoelectric actuators in the 21^st century seem to be oriented toward “politico-engineering” with four keywords, “cooperation, protection, reduction, and continuation”. The sustainability technologies include the following piezoelectric items: (a) Pb-free piezoelectrics, (b) ultrasonic technology for decomposing hazardous materials, (c) reduction of contamination gas, (d) piezoelectric energy harvesting, and (e) device improvement with high energy-efficiency. On the other hand, the following crisis technologies have been developed with piezoelectrics: (a) detection and neutralization technologies of infectious/epidemic diseases such as anthrax, (b) autonomous unmanned underwater, aerial, and land vehicles with piezoelectric actuators, (c) pin-point target weapons, (d) high voltage supplies with piezoelectric transformers, and (e) compact energy sources for remote actuating/sensing systems.

We report the development of an extrinsic self-healing coating system that shows no fluorescence from the intact coating, yellowish fluorescence in cracked regions, and greenish fluorescence in healed regions, thus allowing the separate monitoring of cracking and healing of coatings. This fluorescence monitoring self-healing system consisted of a top coating, an epoxy matrix resin containing mixed dye-loaded in single microcapsule. The dye-loaded microcapsules consisted of a poly(urea-formaldehyde) shell encapsulating a healing agent containing MAT-PDMS and styrene, a photo-initiator and a mixture of two dyes, one that fluoresces only in the solid state (DCM) and a second that fluoresces dramatically increased in the solid than solution state (4-TPAE). A mixture of the healing agent, photo-initiator and the two dyes was yellow due to fluorescence from DCM. On UV curing of this mixture, however, the color changed from yellow to green and the fluorescence intensity increased due to fluorescence from 4-TPAE in the solid state. When a self-healing coating embedded with microcapsules containing the DCM/4-TPAE dye mixture was scratched, the damaged region exhibited a yellowish color that changed to green after healing. Thus, the self-healing system reported here allows the separate monitoring of cracking and healing based on changes in fluorescence color.

Ever since the discovery of dendritic cells by Ralph Steinman and Zanvil Cohn in 1973, it is increasingly evident that dendritic cells are integral for adaptive immune responses, and there is an undeniable focus on them for vaccines development. Fungal infections, often thought in-nocuous, are becoming significant threats due to increased immunocompromised or im-mune-suppressed population and climate change. Further, the recent COVID-19 pandemic unraveled the wrath of fungal infections and devastating outcomes. Invasive fungal infections cause significant case fatality rates ranging from 20% to 90%. Regrettably, no licensed fungal vaccines exist, and there is an urgent need for preventive and therapeutic purposes. In this re-view, we discuss the ontogeny, subsets, tissue distribution, and functions of lung dendritic cells. In the latter part, we summarize and discuss the studies on the DC-based vaccines against pulmonary fungal infections. Finally, we highlight some emerging potential avenues that can be incorporated for DC-based vaccines against fungal infections.

A power factor correction (PFC) rectifier is compulsory for any electronic circuitry connected to the electrical grid. The majority of PFCs that are utilized are based on a step-up converter that supplies high DC voltage at its output terminal. Electric vehicle battery voltage varies from a few hundred to almost a thousand volts. Thus, an additional conversion step is obligatory when designing an all-brand universal charger. This paper presents a new type of front-end versatile step up / down three voltage level PFC. The rectifier can operate in continuous conduction mode or discontinuous conduction mode. First, the rectifier’s principle of operation is described, and then an innovative rectifier is analyzed for continuous and discontinuous conduction modes. Finally, the proposed theory is experimentally validated in a multiplier-less dual loop mode at discontinuous conduction modes. It was shown that although there is no multiplier use in the control circuitry, the power factor is near unity. It was revealed that the rectifier could swing the output voltage from 50 V to 900 V while the input voltage was 230 Vrms. The innovative topology suits any standard PFC rectifier, three-level voltage supplement, and dual-stage low-voltage power supply.

A three-phase multilevel inverter (MLI) synthesized with 31-levels in the output voltage is used to provide ac supply to a three-phase, squirrel-cage induction motor. The gating angles required for thirty power switches in MLI are optimized by both Genetic Algorithm (GA) and Gray Wolf Op-timization (GWO). In the optimization technique, the optimal angles are determined by solving the trigonometric equations from the Fourier analysis for targeting minimum total harmonic distortion (THD) at the MLI output. Simulation model and experimental prototype are developed for performance analysis and validation. The results obtained demonstrate that the MLI is effec-tively able to produce 31-levels of three-phase ac output voltages with THD not exceeding 5% when loaded with a resistive load and a three-phase induction motor. The voltages and currents are measured and recorded for different loads and operating conditions, including the amount of energy consumed by the loads, as well as frequency analysis, which shows the absence of most of the triple harmonics that have a negative impact on the efficiency of the inverter.

This paper presents the mathematical modeling for designing a 10[kW] DC-AC inverter system from 48 [V] DC to 120 V ACrms, considering its non-linear operation, allowing to obtain a detailed simulation to assess the proposed fuzzy PI control (with anti-windup action) and its optimal operation. The performance assessment of the converter was carried out with the discrete treatment of the voltage and current signals using spectral analysis, filtering considerations, and evaluation of limit cycle technique to determine the system's stability. The main results showed that THD at the filter output (transformer and capacitor) was around 0.0322% and 0.0632% at nominal load in open loop and closed loop, respectively. The inverter system presented more sensitivity in the current signal with a ripple at 120 [Hz] of 2.02% and at 5000 [Hz] of 10.62% (at nominal load). However, when the system operates in a closed loop, the current ripple at 120 [Hz] is 2.38% and at 5000 [Hz] is 10.62%.

This study investigates the nonlinearities in three-phase inverters for SiC-based systems and compares their performance to IGBT-based systems. An analytical model of inverter voltage distortion is developed, which accounts not only for dead time (td), switching delay time, switching frequency (fs), and voltage drops of power devices, but also for output parasitic capacitance (Cout). Experimental tests validate the model, which provides a more accurate estimate of the inverter’s output phase voltage distortion. The power device characteristics are obtained from datasheets, while Cout is determined through experimentation. Three-phase inverters with varying switching frequencies, fundamental frequencies, and dead-time values are used in simulations and experiments to determine the influence of nonlinearity on phase voltage deviation and current distortion. The results show that, due to SiC devices’ faster switching time, the phase voltage deviation and phase current distortion are lower in SiC-based inverters than in IGBT-based ones for high-frequency applications, as the dead time can be reduced.

This paper proposes a novel micro-grid structure, which can operate fully-autonomously with inherent seamless switching. It can operate independently in both grid-connected and islanded mode as a self-governed entity without relying on the utility grid. An AC/DC/AC converter is employed as the interface between the micro-grid and the utility grid, which enables the two entities to have different voltages in grid-connected mode. Seamless switching between operation modes can be achieved naturally. The micro-grid is regulated to exchange predefined amount of power with the utility grid in grid-connected mode. This will benefit the power dispatching algorithm of the power system. The predefined power is estimated based on power forecasting of local renewable generations and loads with consideration of the Sate of Charge (SOC) of the battery, and is updated and broadcasted every certain period. A small scale AC micro-grid with a rotating generator, battery storage and solar arrays etc. is built for investigation. Matlab/Simulink results are provided to validate the robustness and flexibility of proposed micro-grid and its operation strategy.

The implications of urban revitalization, gentrification, and residential migration have attracted widespread interest and ongoing debate among scholars across a range of disciplines. While a significant body of literature explores race and class interactions within urban gentrifying neighborhoods, few have examined the environments that await those displaced by this process. This study explores the social and political impact of urban gentrification and class stratification within the black community by examining responses of black middle class residents in Prince George’s County, MD to the growing in-migration of low-income and minority residents from Washington, DC. Drawing on data from the U.S. Census Bureau, a multi-neighborhood sample of ninety-five black middle class residents of Prince George’s County, and informal interviews with subject-area experts, this study explores how race and class shape residential decisions and their impact on residential mobility initiatives. Residents responded to a 26-item survey that covered demographic information, political and community engagement, and their attitudes and beliefs about the poor, changes in their community, and racial unity and responsibility. Findings from cross tabulations and binary logistic regression indicate that lower middle class residents are the most likely to resist in-migration by exiting their communities and/or voting against proposals to create affordable housing options. Core and upper middle class residents were the most likely to stay in their neighborhoods despite increases in low-income migration, to vote in support of policies to create affordable housing options and to believe their responsibility to poor blacks could include sharing residential space.

The objective of the prototype is to eliminate the polluting contamination of water sources, due to the leak of industrial waste without any kind of treatment, mainly generated by the industries and home sector. In this project, a prototype of water purification by plasma technology has been designed. The prototype will convert contaminated water into the plasma stream and eliminate the pathogens from the water by exposing it to ultraviolet radiation and plasma sterilisation. The polluted water will be accelerated at high speed using a water pump in order to convert it into a liquid-gas mixture for ease plasma generation. This process will be achieved when the electric supply from a source of alternating current (AC) is applied to the water by means of high voltage electrodes. After which, the mixture slows down to return into liquid form and the clean water is obtained. The whole process takes place without significantly raising the temperature also knows as non-thermal plasma. The device also has an automatic flow and pressure control system. Finally, a short feasibility study has been conducted on the water samples collected and report obtained from Chennai Metropolitan Water Supply and Sewage boards are reported. It has been concluded that this new plasma-based water treatment system will be more efficient and cheaper than the current wastewater treatment techniques and can be used in the future as the replacement of current secondary and tertiary treatments of industrial wastewater.

The paper presents the design stages of a single-phase Silicon Carbide bidirectional DC-AC converter. This includes the LCL filter design responsible to meet grid connection requirements. A 3kW laboratory prototype of the power converter is built employing a low-cost phase locked loop and its results are presented. The design of the low-cost phase locked loop and its implementation are depicted in some detail.

This study investigated whether positive self-talk (ST) over 4 weeks would improve standing long jump (SLJ) performance in men and women in their 20s. The participants of this study were 36 men and 28 women, selected through interviews with male and female students. The test subjects’ performance was measured 10 times over a 4-week period, 2-3 sessions per week. In the experimental group, participants performed SLJ while reciting positive ST; the control group performed SLJ without any specific conditions. A pre-and post-intervention survey was conducted using the Rosenberg Self-Esteem Scale (RSE). The results revealed a significant difference in the performance of experimental group (p < 0.05), while no significant difference was observed in the control group. RSE survey results also showed a significant difference only in the experimental group (p < 0.05). These findings indicate that self-affirmation yields positive effects on SLJ performance.

Background: The adoption of self-care behaviors among patients with congestive heart failure (CHF) is essential for the management of their health condition. However, there is a lack of tools for estimating self-care in CHF patients. We aim to develop and validate the Hippocratic heart failure self-care scale (HHFSCS). Methods: the scale includes 22 items which are reviewed by a committee of experts. Individuals indicate the frequency at which they follow each self-behavior on a five-point Likert scale. Adult patients with CHF (n=250) from a General Hospital, in Athens, were participated in the study from June 2020 to March 2021. Reliability coefficients and Explanatory Factor Analysis (EFA), using a Varimax rotation and the Principal Components Method were used to assess the psychometric measurements. Results: The Cronbach’s alpha coefficient of the HHFSCS was 0.807. The exploratory factor analysis identified two domains that accounted for 88.44% of the variance of the scale items; however, each sub-scale could not be used as an independent scale. Finally, the test-retest showed a significant strong correlation (r=0.973, p&lt;0.001). Conclusions: The HHFSCS is a reliable and valid tool for assessing self-behaviors in CHF patients. Health professionals can use it in their clinical practice to improve the management of patient’s health conditions.

Online education allows learners to develop knowledge and skills flexibly and conveniently—such observation among students whose characteristics involve student engagement, self-regulation, and self-efficacy. However, studies to characterize Filipino online learners seem lacking. Thus, this study aimed to characterize science education tertiary students in the Philippines concerning their online student engagement (OSE), self-regulated learning (SRL), and online learning self-efficacy (OLSE). The unprecedented events brought by COVID-19 pandemic also urged the implementation of online modalities while there is no available information on students’ online learning profiles. Hence, researchers used a survey research employed through ex post facto approach to determine the effects of the demographic profile on OSE, SRL, and OLSE. The survey was participated by N=373 respondents who answered the questionnaire with informed consent administered via Google Forms. Results revealed that OSE indicators moderately characterized students, while SRL and OLSE indicators are true of them, substantiated by the overall mean M=3.85(SD=0.90), M=3.86(SD=0.92), and M=3.14(SD=0.73), respectively. Also, multivariate tests showed no significant effect among the independent groups (p&gt;0.05), except for gender and OLSE interaction (p&lt;0.05) so, only in OLSE was a significant difference found in gender. In conclusion, Filipino online learners are moderate across aspects of student engagement, self-regulation, and self-efficacy.

Secure attachment, developed through consistent relationships with attachment figures in childhood, is a crucial factor in fostering healthy interpersonal relationships and a positive self-perception. This research aimed to assess how perceived security, as an indicator of secure attachment, predicts adult self-concept through the mediating effects of resilience and positive self-esteem. A quantitative, cross-sectional, and non-probabilistic study was conducted with 383 participants, of whom 76.2% were females, aged between 17 and 86 years (M = 28.52, SD = 12.23). Correlational analyses revealed significant positive associations between perceived security, self-concept, resilience, and positive self-esteem. Path analysis demonstrated that resilience and positive self-esteem sequentially mediate the relationship between perceived security during childhood and adult self-concept (Total Effect R2 = .34, F(1,381) = 193, p < .001; Indirect effect of sequential mediation b = .02, CI 95% [.01, .04]). Findings suggest that the ability to cope with ad-versity and personal acceptance underlie the impact of perceived security on self-concept. It is recommended to promote not only secure attachment in family interventions but also resilience and self-esteem in programs targeting adolescents, youth, and adults.

Purpose: To identify the impact of dealing with COVID-19 patients in clinical areas on nurses' professional self-concept and self-confidence. Background: Professional self-concept is considered a critical factor in the recruitment/retention process in nursing, nursing shortage, career satisfaction, and academic achievements. Professional self-confidence is also a crucial determinant in staff satisfaction, reducing turnover, and increasing work engagement. Design: Descriptive, comparative study. Methods: The study was conducted between February to May 2021 by utilizing a convenience sampling technique. A total of 170 nurses from two facilities were recruited from two COVID-19 and non-COVID-19 designated facilities. The level of professional self-concept and self-confidence was assessed by utilizing the Nurses' Self-Concept Instrument and Self-Confidence Scale. Results: The professional self-concept level among the exposed group to COVID-19 patients was lower than the comparison group, while the professional self-confidence level among the exposed group to COVID-19 patients was similar to the comparison group. On the other hand, the satisfied staff and those who received professional training in dealing with COVID-19 patients reported a higher level of professional self-concept. Conclusions: Dealing with COVID-19 patients has an impact on professional self-concept; the exposure group was lower than those who did not deal with COVID-19 patients, while the professional self-confidence level among the exposed group was similar to the comparison group. Getting professional training in dealing with COVID-19 patients and being satisfied at work were significant factors in improving the professional self-concept. Policymakers should create strategies that target the improvement of professional training in dealing with COVID-19 patients.

Background: Level of perceived competence as a basic psychological need could trigger achievement of diabetes self-management goals. Due to lack of a specific data collection tool to measure level of self-competence among Persian speaking patients with diabetes this study was conducted for cross-cultural adaptation and psychometric assessment of the Persian version of Perceived Competence Scale for Diabetes (PCSD-P). Methods: Standard translation/back-translation procedure was carried out to prepare a preliminary draft of the PCSD-P. Content and face validity of the early draft were checked by an expert panel including 15 scholars in the field of health education and promotion as well as nursing education with experience of working and research on diabetes. The final drafted questionnaire was completed by 177 randomly selected patients with type 2 diabetes. Based on the collected data structural validity of the contrived version was appraised using exploratory and confirmatory factor analysis (EFA, CFA). Cronbach's alpha and Intraclass Correlation coefficients (ICC) were used to check the scale’s reliability and internal consistency. ; (3) Results: The estimated measures of Content Validity Index (CVI= 0.95) and Content Validity Ratio (CVR= 0.8) were in the range of acceptable recommended limits. The EFA analysis results demonstrated a single factor solution according to the items’ loadings for the component. The model fit indices i.e. RMSEA= 0.000, CFI=1, TLI=1, GFI= 0.998, NFI= 0.999 RFI= 0.995 confirmed consistency of the hypothesized one-factor solution. Values of the internal consistency and reliability coefficients were also in the vicinity of acceptable range (α= 0.892, ICC=0. 886, P= 0.001). Conclusions: The study findings revealed good internal validity and applicability of the PCSD-P to measure degree of self-competence among Persian speaking type 2 diabetes patients to manage the chronic disease. Due to unrepresentativeness of the study sample future cross-cultural test of PCSD-P on diverse and broader Persian speaking populations is recommended.

This paper addresses the development of knowledge and assessment-centered learning approaches within a reflective learning framework in a first year physics class in a university faculty. The quality of students’ reflections was scored using a Self-reporting Reflective Learning Appraisal Questionnaire at the end of each learning approach. The results showed the differences between the approaches based on reflections on the learning control through self-knowledge, by connecting experience and knowledge, as well as through self-reflection and self-regulation. Assessment-centered activities fundamentally help students identify aspects of their attitudes towards, as well as regulate, their sustainability learning education.

DC-connected parallel inverter systems are gaining popularity in industrial applications. However, such parallel systems generate excess current ripple (harmonics) at the DC-link due to harmonic interactions between the inverters in addition to the harmonics from the PWM switching. These DC-link harmonics cause the failure of fragile components such as DC-link capacitors. This paper proposes an interleaving scheme to minimize the current harmonics induced in the DC-link of such a system. The results show that when the carrier waves of the two inverters are phase-shifted by 90° angle, the maximum high-frequency harmonic ripple cancellation occurs, which reduces the overall RMS value of the DC-capacitor current.The outcome of this proposed solution is a cost-effective DC-harmonics mitigating strategy for the industrial designers to practically configuring multi-inverter systems, even when most of the drives are not operating at rated power levels. Experimental and simulation results presented in this paper verify the effectiveness of the proposed carrier-based phase-shifting scheme for two different configurations of common DC connected multi-converter systems.

Self-regulatory Self-efficacy belief (i.e., SRSE) represents a fundamental factor for adjustment in adolescence, as a vehicle to promote positive behaviors and protect youths from transgressions and maladjustment Bandura et al., 2003; LaRose et al., 2010). Research attested that, during adolescence, boys are more vulnerable to externalizing behaviors than girls, especially when they perceive themselves as scarcely capable of managing and orienting their behaviors, and when they possess impairments in impulsivity (Bandura et al., 2001; Muris, 2006). Previous studies firmly supported the key role of SRSE especially in the offline context in adolescence, but very few studies investigated its impact in the online context, although nowadays Internet represents one of the most significant environments for youths’ daily lives (LaRose et al., 2010; Favini et al., 2023). Thus, we aimed to examine the protective moderating role of SRSE in online and offline aggressive behaviors, beyond youths’ temperamental vulnerabilities, such as high levels of impulsivity. A sample of 318 Italian adolescents (Mage=15.21; SD=.51; 57% boys; 40% girls; 3% third gender) were asked to complete the Impulsivity Scale at Wave1, online and offline aggressive behaviors scales at Wave 2, and SRSE at Wave 2. Multiple-group-by-gender moderation model evidenced that, for what concerns online aggression, beyond the direct effects of impulsivity in boys and girls, SRSE directly affected online aggression and mediated the effect of impulsivity in girls. In contrast, impulsivity significantly affected offline aggressive behaviors only indirectly through the effects of SRSE, and SRSE directly influenced these behaviors in both genders. These results hold for the effects of youth’s age, sexual orientation, socioeconomic status, and years of education completed. This work preliminary evidenced that, contrary to previous studies which focused especially on the vulnerability of boys to aggressive conduct, impulsivity had direct effects on online aggressive behaviors in girls, and SRSE can protect adolescents of both genders in the online context, by predicting low online aggression, and represent a protective factor from the indirect effects that im-pulsivity impairments can have also in the offline context.

Today, issues related to people’s mental health and well-being have been described as a challenge for society, globally as well as in Sweden. This calls for new approaches to mental health promotion. The aim was to evaluate the adequacy of the content and structure, describing experiences of study circles as a means of supporting participants' self-care and self-compassion. The overall design is a descriptive, QUAL+quan design, where quantitative and qualitative results are integrated. Five participants participated in a focus group interview, of whom four completed questionnaires. One individual interview was conducted with the study circle leader. Study circles can be an arena for mental health promotion as learning and sharing of experience contributes to a sense of coherence, as well as self-compassion and a genuine concern for one’s own and others' wellbeing, but not considered an alternative to psychiatric care, for those in need of professional services. Study circles can be a possible means to support self-care and thereby promote mental health in the general population, and a valuable contribution to public health. However, in addition to modifications of the content, further research is needed on the qualifications for study circle leaders as well as the dissemination of study circles.

Self-compacting concrete (SCC) production is a complex operation that requires finding a good combination and a suitable dosage of each of its constituents. Several formulation methods have been developed to meet the workability requirements of SCC. In this paper, the relationships between the fresh properties of SCC based on local metakaolin (MK) and the spreading of its mortar was investigated. The results showed the existence of good correlations between the spreading of the mortar and the fresh state properties of the related SCC and that the MK substitution rate did not affect these correlations. The choice of the mortar flow rate should target appropriate fresh properties of the SCC and a viscosity enhancing agent (VEA) could be used if the mix is too fluid and present an instability.

Based on the sensitive sum frequency generation cross-correlation frequency-resolved optical gating (SFG-XFROG) measurement setup, besides the pulse broadening, blue shift, red shift and obvious pulse acceleration, we observed the soliton evolution when the low energy soliton pulse with wavelength of 1555nm transmit through the Si photonic crystal waveguide. The measurements were nicely matched with the simulation results, which are achieved with an optimized nonlinear Schrödinger equation (NLSE) modeling. The effects of various parameters of the silicon photonic crystal waveguides and the incident pulses on the pulse transmission were also analyzed, including the nonlinear effects and dispersion such as the self-phase modulation (SPM), self-steepening (SS) and intra-pulse Raman scattering(IRS). The results help us understand further the ultra-fast nonlinear dynamics of soliton in silicon-based waveguides, and even open a novel way for soliton-based functional elements in CMOS-compatible platforms.

Building on the Sustainable Happiness Model, this study examined how congruency between ideal self-image and brand image influence a sense of happiness. The findings show that when ideal self-image and ideal social self-image are congruent with brand image a sense of happiness can be enhanced through brand identification and positive emotions. This study contributes to literature as it reveals the mechanism of how congruency between ideal self-image and brand image positively affect happiness.

Purpose: This study aims to analyze the factors that affect the behavior of user-defined avatars in different virtual environments, and compare the differences in public self-awareness, self-expression, and emotional expression among customized avatars in multiple virtual contexts. Methods: Using a between-subjects experimental design, two random groups of participants were asked to customize avatars for themselves in two contexts, a multiplayer online social game (MOSG) and a virtual meeting (VM). i.e. a relaxed and a serious social environment. Results: When subjects perceived a more relaxed environment, the customized avatars had less self-similarity, and the subjects exhibited a stronger self-disclosure willingness and enhanced avatar wishful identification; nevertheless, public self-consciousness was not increased. When subjects perceived a more serious environment, the customized avatars exhibited a higher degree of self-similarity, and the subjects exhibited a greater self-presentation willingness, along with enhanced identification of avatar similarity, and increased public self-consciousness. Conclusions: Participants expressed positive emotions, suggesting that avatars play a positive role in various virtual contexts. The virtual context affects the self-similarity of user-customized avatars, and avatar self-similarity affects self-presentation and self-disclosure willingness, and these factors will affect the behavior of the user-customized avatar. This study contributes suggestions to the Metaverse avatar customization platform design.

The growing demand for high-power DC Fast Charging (DCFC) stations for Electric Vehicles (EVs) is expected to lead to increased peak power demand and reduction of grid power quality. To maximize the economic benefits and station utilization under practical constraints set by regulatory authorities and DCFC station operators, this study explores and provides methods for connecting DCFC stations to the grid employing low power interconnection rules and Distributed Energy Resources (DERs). The system uses automotive Second Life Batteries (SLBs) and Photovoltaic (PV) systems as energy buffers and local energy resource to support EV charging and improve the station techno-economic feasibility through load shifting and charge sustaining. The optimal sizing of the DERs and the selection of the grid interconnection topology is achieved by means of a Design Space Exploration (DSE) by means of exhaustive search approach to maximize the economic benefits of the charging station and to mitigate high-power demand to the grid. Without loosing of generality, this study considers a range of DER sizes, grid interconnection specifications, and related electricity tariffs of American Electric Power (AEP) Ohio and the Public Utility Commission of Ohio (PUCO). Various scenarios and strategies have been defined to account for the interconnection requirements of the grid to the DCFC with DERs. The system’s techno-economic performance of different scenarios has been analyzed and compared using a multitude of metrics.

The coupling of AC and DC power will impact the protective actions on the AC side and pose a threat to the stable operation of the interconnection system. Therefore, a new longitudinal protection method is proposed based on the comprehensive distance similarity of voltage waveforms. Initially, the measured voltage and current data are extracted to calculate the reference voltage, and the voltage waveform fitting is optimized. Subsequently, the Euclidean dynamic time warp (DTW) distance and entropy weight method are utilized to process the voltage waveform, enabling the calculation of its comprehensive distance similarity. This similarity is adopted to determine fault location. A hybrid DC multi-feed AC/DC interconnection system, incorporating line commutated converter-voltage source converter (LCC-VSC) and line commutated converter-modular multilevel converter (LCC-MMC), was established in PSCAD, and fault data was simulated and output. The effectiveness of the protection scheme was validated using MATLAB. Simulation results demonstrate that the proposed method can accurately distinguish between faults inside and outside a region. When compared to existing protection methods, it demonstrates superior performance in resisting transition resistance and noise interference, while also mitigating the impact of data asynchronicity. The speed and reliability of the method are further enhanced.

Stray currents can cause very rapid degradation and material loss at the points where the current leaves the metal and enters the electrolyte. Nowadays, many resources are invested in the protection of jeopardized structures, such as buried pipelines, from stray current corrosion. This paper describes the measures that need to be considered in the design and construction of track structures to ensure high rail-to-ground resistance and consequently reduce stray currents. The main conclusions from existing guidelines and standards for reducing and controlling stray currents that are applied by various track operators are presented in the paper. Rail-to-ground resistance in different types of tracks structures and rail fastening systems is analysed and optimal type of the track and type of the fastening system is defined. The grounding schemes used on the tracks and their influence on stray current values are described, as well as the influence of traction power substation and rail cross bonding on stray current. Since it is not necessary to apply all the measures described to the same track structure, the paper gives recommendations on which measures to apply when building tracks with continuously fastened rails and which to apply when building tracks with discretely supported and fastened rails.

Stray current is a relevant phenomenon in particular for DC electrified transportation systems, affecting the track and infrastructure within the right of way and other structures and installations nearby. It worsens with time and the level of protection depend on timely maintenance, besides correct design choices. The assessment of track insulation is the starting point for both stray current monitoring systems and at commissioning or upon major changes. Standardized methods (ref. EN 50122-2, or IEC 62128-2) are almost unchanged in the last 20 years, but suffer from accuracy issues and variability due to parameters and conditions not under operator’s control. A critical discussion and analysis of the sources of variability and practical constraints is proposed, followed by the evaluation of uncertainty, with the objective not only to assess the accuracy of provided results, but to foster research on innovative, more flexible and accurate, methods.

This paper assesses the behaviour of active distribution networks with high penetration of renewable energy sources when the control is performed in a centralised manner. The control assets are the on-load tap changers of transformers at the primary substation, the reactive power injections of the renewable energy sources and the active and reactive power exchanged between adjacent feeders when they are interconnected through a DC link. A scaled-down distribution network is used as testbed to emulate the behaviour of an active distribution system with massive penetration of renewable energy resources. The laboratory testbed involves hardware devices, real-time control, and communication infrastructure. Several key performance indices are adopted to assess the effects of the different control actions on the system operation. The experimental results demonstrate that the combination of control actions enables the optimal integration of a massive penetration of renewable energy.

The capacitor-mismatch among diverse defects caused by the manufacturing process variations significantly affects the linearity of capacitor-array used to implement the capacitive digital-to-analog converter (CDAC) in the successive-approximation-register (SAR) analog-to-digital converter (ADC). Accordingly, the linearity of the SAR ADC is limited by that of capacitor-array, resulting in serious yield loss. This paper proposes an efficient foreground self-calibration technique to enhance the linearity of the SAR ADCs by mitigating the capacitor-mismatch based on the split ADC architecture along with variable capacitors. In this work, two ADC channels (i.e., ADC1 and ADC2) for the split ADC architecture include their capacitive DACs (CDACs) whose binary-weighted capacitor-arrays consist of variable capacitors. A charge-sharing SAR ADC is used for each ADC channel. In the normal operation mode, their digital outputs are averaged to be the final ADC output, as in a conventional split ADC. In the calibration mode, every single binary-weighted capacitor for the two ADCs is sequentially calibrated by making parallel or/and antiparallel connection among two or thee capacitors from the two channels. For instance, because the capacitors of the CDACs ideally exhibit the binary-weighted relation as Cn=2×Cn−1, variable capacitor Cn of ADC1 can be updated to be closest to the sum of Cn−1 of ADC1 and Cn−1 of ADC2 for the calibration. For the process, the two capacitor-arrays of the two ADCs can be reconfigured to be connected to each other, so that Cn of ADC1 can be connected with two of Cn−1 of ADC1 and ADC2 in antiparallel. The two voltages at the top and the bottom plates of the CDAC are compared by a comparator of ADC1, and the comparison results are used to update Cn. This process is iterated, until Cn is in agreement with the sum of two of Cn−1. Finally, all the capacitors can be calibrated in this way to have the binary-weighted relation. The simulation results based on the proposed work with a split SAR ADC model verified that the proposed technique can be practically used, by showing that the total-harmonic-distortion and the signal-to-noise-and-distortion ratio were enhanced by 21.8-dB and 6.4-dB, respectively.

Background: This study aimed to develop and evaluate a dietary self-care promotion program for hemodialysis patients based on Hurley's self-efficacy model. Methods: The needs of hemodialysis patients were identified, and an online community-based dietary self-care promotion program was developed with expert evaluations. 44 hemodialysis patients were randomly assigned to an experimental group (n=22) and a control group (n=22). The program was applied to the experimental group for four weeks. Before and after the intervention, as well as four weeks after the intervention, dietary self-efficacy, dietary self-care behavior, interdialytic weight gain, serum phosphorus, and serum potassium were assessed in both groups. Results: Significant differences over time and between groups were observed in dietary self-efficacy, interdialytic weight gain, serum phosphorus, and serum potassium. The interaction between time and group was also significant. While no significant differences were found over time in dietary self-care behavior, significant group differences and interaction effects between time and group were identified. Conclusions: The results indicate that the dietary self-care promotion program using an online community for hemodialysis patients is more effective in enhancing dietary self-efficacy and dietary self-care behavior compared to conventional treatment. This suggests the clinical applicability of the proposed dietary self-care promotion program.

In recent decades, considerable attention has been focused on the design and development of surfaces with defined or tunable properties for a wide range of applications and fields. To this end, self-assembled monolayers (SAMs) of organic compounds offer a unique and straightforward route of modifying and engineering the surface properties of any substrate. Thus, alkane-based self-assembled monolayers constitute one of the most extensively studied organic thin-film nanomaterials, which have found wide application in antifouling surfaces, control of wettability or cell adhesion, sensors, optical devices, corrosion protection, organic electronics, among many other applications. Some of which have led technological transfer to industry. Nevertheless, recently, aromatic-based SAMs have gained in importance as functional components, particularly in molecular electronics, bioelectronics, sensors, etc., due to their intrinsic electrical conductivity and optical properties, opening up new perspectives in these fields. However, some key issues affecting device performances still need to be lifted off to ensure their full use and access to novel functionalities such as memories, sensors, or active layers in optoelectronic devices. In this context, we will present herein recent advances of p-conjugated systems-based self-assembled monolayers (e.g., push-pull chromophores) as active layer and their applications.

Health self-tracking is an ongoing trend as software and hardware evolve, making the collection of personal data not only fun for users but also increasingly interesting for public health research. In a quantitative approach we studied German health self-trackers (N=919) for differences in their data disclosure behavior by comparing data showing and sharing behavior among peers and their willingness to donate data to research. In addition, we examined user characteristics that may positively influence willingness to make the self-tracked data available to research and propose a framework for structuring research related to self-measurement. Results show that users' willingness to disclose data as a "donation" more than doubled compared to their "sharing" behavior (willingness to donate= 4.5/10; sharing frequency= 2.09/10). Younger men (up to 34 years), who record their vital signs daily, are less concerned about privacy, regularly donate money, and share their data with third parties because they want to receive feedback, are most likely to donate data to research and are thus a promising target audience for health data donation appeals. The paper adds to qualitative accounts of self-tracking but also engages with discussions around data sharing and privacy.

The recommendations of the panel of experts on the further development of the ‘High-Tech Strategy’ of the Government of the Federal Republic of Germany designate the biologization of economic processes along with digitization as the central driver of societal change. Various fields such as the 'biologization of materials research' were then defined in the 'Bio-Agenda' in order to walk the path from biology to innovation. In view of this perspective, we describe how the use of biological materials and mechanisms can lead to resource conservation, the production of intelligent materials and new technological and medical applications. Our strategy, based on research on ‘Biointerfaces in Technology and Medicine’, aims at the development of modular biohybrid systems that could be used as 'biofactories of the future' for sustainable production processes. To achieve this goal, in a first phase already known technologies have to be further refined and integrated in order to obtain and apply compartmentalized reaction systems on different length and time scales. In a second phase, the resulting functional units will be employed to develop dissipative systems useful for biomedical applications and advanced production processes. From a technical point of view, future success in creating 'something entirely new' will depend crucially on robust and complementary research capabilities. Since the close connection of engineering and life sciences at KIT provides an excellent basis for this endeavor, we consider the above perspectives to be feasible.