A metastable β-Ti alloy, Ti–10V–3Fe–3Al (wt.%), was subjected to thermos-mechanical processing including the compression test at 725°C, which is below the β transus temperature (780°C), and at strain rate of 10-3s-1. The presence of phases was determined using transmission electron microscopy and X-ray diffraction. Although the dynamic recovery took place together with slip, both deformation-induced α˝ martensite and ω were detected as other operating mechanisms for the first time in metastable-β Ti alloys deformed in α+β region. The volume fraction of stress-induced α˝ was higher than that of the same alloy deformed at room temperature due to higher strain applied. Stress-induced twinning was not operational, which could be related to the priority of slip mechanism at high temperature resulted from thermally-assisted nucleation and lateral migration of kink-pairs.

Abstract: High step-up voltage gain nonisolated DC-DC converter have attracted much attention in photovoltaic, fuel cells and other renewable energy system applications. In this paper, by combining input current ripple-free boost cell with coupled-inductor voltage-doubler cell, an input current ripple-free high voltage gain nonisolated converter is proposed. In addition, passive lossless clamp circuit is adopted to recycle the leakage inductor energy and to reduce the voltage spike across the power switch. By utilizing voltage-doubler cell consisting of diode and capacitor, the voltage stress of switch is further reduced and the resonance between the leakage inductor and the stray capacitor of the output diode is eliminated. A low switch-on-resistance low-voltage-rated MOSFET can therefore be employed to reduce the conduction loss and cost. The reverse recovery loss of output diode is reduced, and the efficiency of converter can be improved. Furthermore, the proposed converter can achieve nearly zero input current-ripple and make the design of electromagnetic interference (EMI) filter easy. Steady state analysis and operation mode of the converter is performed. Finally, experimental results are presented to verify the analysis results of the proposed converter.

The regulatory approvals of tumor agnostic therapies have led to reevaluation of the drug development process. Conventional models of drug development are histology-based. On the other hand, tumor agnostic drug development of a new drug (or combination) focuses on targeting a common genomic biomarker in multiple cancers, regardless of histology. Basket-like clinical trials with multiple cohorts allow clinicians to evaluate pan-cancer efficacy and toxicity. There are currently 8 tumor agnostic approvals granted by the Food and Drug Administration (FDA). This includes two immune checkpoint inhibitors, and 5 targeted therapy agents. Pembrolizumab is an anti-PD-1 antibody that was the first FDA approved tumor agnostic treatment for unresectable or metastatic microsatellite instability-high (MSI-H) or deficient mismatch repair (dMMR) solid tumors in 2017. It was later approved for tumor mutational burden-high (TMB-H) solid tumors, although the TMB cut-off used is still debated. Subsequently, in 2021, another anti-PD-1 antibody, Dostarlimab was also approved for dMMR solid tumors in the refractory setting. Patients with fusion-positive cancers are typically difficult to treat due to their rare prevalence and distribution. Gene rearrangements or fusions are present in a variety of tumors. neurotrophic tyrosine kinase (NTRK) fusions are present in a range of pediatric and adult solid tumors in varying frequency. Larotrectinib and entrectinib were approved for neurotrophic tyrosine kinase (NTRK) fusion-positive cancers. Similarly, selpercatinib was approved for Rearranged During Transfection (RET) fusion-positive solid tumors. FDA approved the first combination therapy of dabrafenib, a B-Raf Proto-Oncogene Serine/Threonine Kinase (BRAF) inhibitor, plus trametinib, a mitogen-activated protein kinase (MEK) inhibitor for patients 6 months or older with unresectable or metastatic tumors (except colorectal cancer) carrying BRAFV600E mutation. The most recent FDA tumor agnostic approval is of fam-trastuzumab deruxtecan-nxki (T-Dxd) for HER2-positive solid tumors. It is important to identify and expeditiously develop drugs that have the potential to provide clinical benefit across tumor types.

Background/Objectives: Clinical decision support systems (CDSS) consisting of computerized physician order entry (CPOE) and oncology pathways serve as the foundation of high-quality cancer care. However, the resources needed to develop and maintain these systems have not been characterized for oncology enterprises. Methods: Missing CPOEs for oncology treatments were identified by comparing current CPOEs to those in the Elsevier ClinicalPath treatment pathways. New FDA oncology drug approvals were used to estimate ongoing CPOE build needs. The impacts of missing orders on clinicians and pharmacists were surveyed. Benchmarking from two other large oncology enterprises supported new resource needs to build and maintain CPOE in our EPIC Beacon system. A program to manage oncology pathways and CPOE for an enterprise using EPIC was developed and implemented. Results: Resources and impacts of CDSS for oncology enterprises are described. Program management is described. Conclusions: Updating and maintaining CDSS for an oncology enterprise requires program management and resources for which a framework has not been previously reported. We present this work as a framework for others to understand the components and resources for budgeting and management of CDSS. We report on the work of the City of Hope enterprise using the EPIC electronic health record.

In the present work, vertically aligned ultrathin 2D In2S3 nanosheets are grown with a chemical vapor deposition technique to enhance the photoresponse by increasing surface area, and optical absorption. The 2D vertically aligned In2S3 nanosheets have shown excellent PEC water-splitting in terms of excellent photocurrent density value of 4.5 mAcm-2, incident photon to current conversion efficiency is 53 % and hydrogen production of 90% has been achieved in the visible region with higher stability. Ultrathin vertically aligned In2S3 nanosheets also show high responsivity, high charge carrier density, lesser recombination rate, and a capacious space charge layer for excellent water-splitting performance. This straightforward method of creating ultrathin 2D nanosheets of In2S3 also has significant potential for other fields where effective absorption and charge separations are required, like photodetection, optical electronics, and gas sensing.

The minimum ignition energy (MIE) has been extensively studied via experiments and simulations. However, our literature review reveals little quantitative consistency, with results varying for f=1.0 from 0.324 to 1.349 mJ, and for f=0.9 from 0.22 to 0.944 mJ. Therefore, there is a need to resolve these discrepancies. This RANS study aims to partially address this knowledge gap. Additionally, it presents other flame evolution parameters essential for robust combustion design. Using the reactingFOAM solver we predict the threshold energy required to ignite the fuel mixture. For this, the single step using the Arrhenius law is selected to model ignition in the flame kernel of stochiometric and lean CH₄/air mixtures, allowing it to develop into a self-sustained flame. The ignition power density, an energy quantity normalised with volume is incrementally varied keeping the kernel critical radius r_s constant 0.5 mm in the quiescent mixture of two equivalence ratios fs 0.9, and 1.0, for varied operating pressures 1, 5 and 10 bar at constant initial temperature 300 K. The minimum ignition energy is validated with twelve independent 1 bar data sets both numerical and experiments. Finally, a mathematical formulation of MIE is devised, a function of pressure and equivalence ratio shows a slightly curved relationship.

The present study examined metabolites in Northern wild rice (WLD), the impact of WLD supplemented high fat (HF) diet on gut microbiota, short chain fatty acids (SCFAs) and correlation with metabolism or inflammation versus HF+white rice (WHR) in mice. C57BL/6J mice received HF diet supplemented with 26g% WHR, 26g% WLD, or 13g% WHR+13g% WLD (WTWD) for 12 weeks. The levels of fasting plasma glucose, total cholesterol, triglycerides, insulin resistance, inflammatory cytokines and monocyte adhesion were lower, and the abundances of fecal Lactobacillus gasseri species bacteria and propionic acid were higher in HF+WLD diet-fed mice compared to HF+WHR diet-fed mice (p<0.05). The anti-inflammatory effects of HF+WTWD diet were weaker than that in HF+WLD diet, but were greater than that in HF+WHR diet-fed mice (p<0.05). Relative abundances of fecal Lactobacillus gasseri and propionic acid in HF+WLD fed-mice were higher than that in HF+WHR fed mice. The abundance of fecal L. gasseri and propionic acid negatively correlated with metabolic and inflammatory markers (p<0.05). The findings suggest that WLD dose-dependently attenuated metabolic and inflammatory disorders in HF diet-fed mice. Interactions between WLD components and gut microbiota may upregulate fecal propionic acid and contribute to metabolic and anti-inflammatory benefits of WLD diet-induced insulin resistant mice.

Daily vitamin D supplementation using higher than normal dosing (up to the upper limit, UL) and intermittent (once or twice per week) dosing were studied in patients with increased risk of vitamin D deficiency. Using a PubMed database an adequate search for published randomized control trials and other studies was done and results were analyzed. This review provides overview of use of 7000 IU daily, 30,000 IU per week or twice weekly and 50,000 IU weekly of vitamin D on rapid restore of 25(OH)D concentrations to at least 30 ng/mL in different groups of patients at high risk of vitamin D deficiency. The above mention dosing should be considered in adults with obesity or multi-diseased patients on requiring multi-treatment with the use of several drugs, including drugs affecting vitamin D metabolism. The simple schedule for 7000 IU/day, 30,000 IU/week or twice weekly or 50,000 IU/week, all for 6-8 weeks of use by patients representing the increased risk of vitamin D deficiency were provided for consideration. It appeared that higher daily doses or intermittent doses suggested above are effective, safe and responsive for patient’s preferences.

Background: Chronic exposure to severe hypoxia causes an increase in hematocrit (Hct) and hemoglobin concentration ([Hb]), which can lead to Excessive Erythrocytosis (EE), which could impact physical performance. This work aims to determine the differences in the six-minute walking test (6MWT) outputs between EE and healthy subjects residing at more than 5000 meters. Methods: A prospective, cross-sectional study was performed on 71 men (36 healthy and 25 suffering EE) living in La Rinconada, Peru (5100 m). Basal levels of [Hb] and Hct were obtained. All the subjects per-formed the 6MWT, and distance reached, vital signs, dyspnea, and fatigue (Borg scale) at the end of the test were recorded. Results: The average [Hb] and Hct levels in the control group were 18.7 ± 1.2 g/dL and 60.4 ± 7.1%, respectively, contrasting with EE subjects who showed 23.4 ± 1.6 g/dL and 73.6 ± 5.9% (p < 0.001). However, no statistically significant differences were observed in BMI or other anthropometric parameters. At the end of the 6MWT, the distance traveled, and vital constants were similar between both groups, except for arterial oxygen saturation which was consistently lower in subjects with EE along the test. Conclusion: EE does not significantly affect 6MWT performance at high altitudes nor the hemodynamic control during moderate aerobic exercise of subjects who live permanently in a severe hypoxic environment.

Wind energy is a kind of renewable energy with great potential for development. This study mainly investigated the application of shock waves generated by high-pressure gases (wind energy) for generating energy. In this study, we designed a new supersonic shock wave generator that can be reused without disassembling and assembling bolts and developed a supersonic shock wave monitoring system. This system monitored the velocity of the generated shock waves, which was Mach 3-5, and the output pressure was more than 100 times higher than the input pressure of the shock wave generator tank.Then, we developed a power generation system driven by supersonic shock waves based on the characteristics of the new shock wave generator, which can generate high-pressure and high-speed blast waves and can be reused. The shock wave generator can repeatedly generate high-pressure waves to drive the Tesla turbine and then the magnetic energy generator for power generation. We established a complete control process for power generation driven by shock waves by controlling the valve stem. The system can detect the tank pressure, output pressure, gas flow, rotation speed, voltage, and current during the control process for the performance analysis of power generation.

Buckling defect will appear on the outer surface of the deformed ring during constrained ring rolling (CRR) of aluminum alloy thin wall conical ring with inner high ribs (AATWCRIHR), if the geometrical dimension of the ribs doesn't match the wall thickness. To avoid the buckling defect, a quantitative method for characterizing the degree of the buckling defect is proposed using the area of buckling profile. Then an orthogonal experimental scheme was designed taking the width of the middle rib, thickness of wall, and height of the middle rib as design variables and defining the area of buckling profile as optimization objective. Subsequently, a quadratic polynomial response surface model was established by combining the optimization algorithm with the finite element method (FEM), and the geometrical dimension of the middle ribs of the deformed AATWCRIHR is optimized. Also the optimal parameter combination to minimize the area of buckling profile is obtained and verified using FE simulation. Results show that the AATWCRIHR after optimization doesn’t generate the buckling defect during constrained ring rolling, and it is proved that the quantitative buckling defect representation method and the optimization design method based on the response surface model and the finite element simulation results are feasible for the constrained ring rolling process of the AATWCRIHR.

BKW is a highly efficient Storage Function-type rainfall-runoff model that utilizes the steady-state storage (S) and outflow (Q) of a catchment at different rainfall intensities as the S-Q relation of the catchment. For the inundation nowcasting of urban areas under high-intensity, short-duration rainfall, a Storage Function-type model is a judicious choice. However, S-Q hysteresis exists in the catchment S-Q relation, and BKW is unable to exhibit hysteresis due to assuming that the S-Q relation of a catchment is a nonlinear relation. The S-Q hysteresis can influence the outflow estimation of BKW, reducing the model's accuracy. Through the evaluation of analytical solutions, we found that the change in rainfall intensity dominates the S-Q relation of a catchment. The S-Q relation during a rainfall event is a dynamic process rather than a monotonic nonlinear relation. By applying the dynamic S-Q relation in BKW, we improved BKW to become a highly efficient and accurate rainfall-runoff model for small urban catchments.

So far, scientific studies on high frequency welding (HF) have observed the three main parameters: anode current, welding time and pressure of upper electrode. Some authors have also observed and studied the welding frequency, the power, and the values of the dielectric constants of the materials or the angle of dielectric losses. Due to the complex effects that the parameters have on the quality of the welded joint, it is necessary to extend the research and study the mutual relationships between a large numbers of process parameters on the welded joint in order to achieve satisfactory strength of the welded joint. In this research, the number of considered parameters is increased to 17, each of which is relevant to the processes of HF welding, and their mathematical equations are presented. The research is carried out on a HF welding machine improved with a linear pneumatic actuator for lowering the upper electrode and regulating the compressive force, and a measuring machine with the appropriate measuring method for determining the breaking forces with a tension gage and performing the „T“ test is made. Numerous researches were carried out on the functional changes of the process parameters of the percentage share of the values of the coupling capacitor, the anode current and the welding time on the values of the breaking forces of the welded joints. Based on the conducted research, it was concluded that the optimization of the process parameters of HF machine must be performed before the welding process, which is determined by a certain amount of energy that must be introduced into the material. These parameters are the capacity of the output capacitor, i.e., the value of the electric current flowing through the material and the time for the development of the operating power to produce welded joints with a certain strength and quality of welded joints for a specific material used in the process.

Flails are one of the more contentious and misunderstood classes of medieval weaponry, despite their prevalence in popular media: some researchers question their existence entirely and the bulk of historians are sceptical of widespread temporal and geographical prevalence while others, and a significant volume of period evidence, would argue the contrary. While the expansive use of flails in Eastern Europe and Byzantium is familiar, many Central, Western, and Southern European sources are less well-known or largely forgotten, especially those stemming from the later-early and early-high medieval eras (up to 1250). In this work, I collate and discuss the bulk of the available literary references and artistic depictions of flails and their use alongside some of the archaeological finds from Western, Central, and Southern Europe, with an emphasis on the 12^th and 13^th Centuries. The significance of this volume of evidence is examined, and an assessment of flails as a part of medieval culture and warfare is considered. Collectively, this would suggest that knowledge of flails as instruments of war and associated cultural connotations, if not their actual prevalence and use in warfare, was far more widespread across Europe this time period than has been previously estimated.

In this work, the author employs the quantum hydrodynamic formalism to achieve the geometrization of spacetime for describing the gravitational interaction within the framework of quantum theory. This approach allows for the development of an equation of gravity that is mathematically connected to the fermion and boson fields. This achievement is accomplished by incorporating two fundamental principles: covariance of the quantum field equations and the principle of least action. By considering these principles, a theory is established that enables the calculation of gravitational corrections to Quantum Electrodynamics, and potentially, to the standard model of particle physics as well. The theory also provides an explanation for two phenomena: the existence of a cosmological pressure density similar to quintessence, that is compatible with the small value of the observed cosmological constant, and the breaking of matter-antimatter symmetry at high energies offering insights into why there is an imbalance between the two in the early universe. In the cosmological modeling of the theory, there exists a proposal to account for the formation of supermassive black holes that are accompanied by their own surrounding galaxies, without relying on the process of mass accretion. The model, in accordance with recent observations conducted by the James Webb Space Telescope, supports the notion that galactic configurations were established relatively early in the history of the universe, shortly after the occurrence of the Big Bang.

Background: In regenerative dentistry the graft material influences the success. It should act as an osteoconductive scaffold, providing a mineral substrate during resorption and inducing the activity of osteoinductive cells capable of producing new bone, platelet growth factors, and cell differentiation factors inducing the differentiation of undifferentiated mesenchymal cells into. Given that dentin shares many biochemical characteristics with bone tissue, it has recently attracted considerable interest as a biomaterial for bone repair. The aim of this study is to compare two grinder types in order to determine the optimal method for producing dentinal particles using a mechanical grinder. Materials and methods: A sample of 40 natural human teeth without restorations, prostheses or root canal treatments was used and divided into two groups subjected to two different grinder speeds (high-speed and low-speed). The high-speed showed a greater dispersion (53.5+-9.89% of the tooth) due to the pulverisation (highly thin granules) of part of the tooth. The low-speed grinder does not pulverize the dentin and the percentage of tooth loss is 9.16+/-2.34%. Conclusion: The low-speed gringer allows to save a major part of the tooth and to have a maximum quantity of graft material but requires more time. Further studies must be promoted to optimise the grinding procedures.

Al has very good corrosion resistance and corrosion properties. The corrosion resistance of Al cast alloys is different because these alloys contain a lot of elements. Especially in secondary alloys which contain more impurity elements from which Fe is the most common. This study deals with secondary AlSi7Mg0.3 cast alloys which contain more Fe and are affected by a chloride corrosion environment. This environment was selected based on the application of castings in the automo-tive industry. The main object was to research the effect of such an environment on basic me-chanical properties and fatigue properties. The results show that a higher Fe content does not lead to a significant reduction in the properties of the casting and the chloride environment is not so harmful. Therefore, can be stated that the investigated secondary sand-cast experimental materials can replace the primary alloys without losing the required corrosion and mechanical properties.

The DEP force is usually calculated from the object’s point of view using the interaction of the object’s induced dipole moment with the inducing field. Recently, we described the DEP behavior of high- and low-conductive 200-µm 2D spheres in a square 1x1mm chamber with a plane-versus-plane electrode configuration from the system’s point of view. Here we extend our previous considerations to the plane-versus-plane and pointed-versus-pointed electrode configurations. The trajectories of the sphere center and the corresponding DEP forces were calculated from the gradient of the system’s overall energy dissipation for given starting points. The dissipation’s dependence on the sphere’s position in the chamber is described by the numerical “conductance field”, which is the DC equivalent of the capacitive charge-work field. While the plane-versus-plane electrode configuration is field-gradient free without an object, the presence of the highly or low-conductive spheres generates structures in the conductance fields, which result in very similar DEP trajectories. For both electrode configurations, the model describes trajectories with multiple endpoints, watersheds, and saddle points, very high attractive and repulsive forces in front of pointed electrodes, and the effect of mirror charges. Because the model accounts for inhomogeneous polarization within the objects, the approach allows the modeling of the complicated interplay of attractive and repulsive forces near electrode surfaces and chamber edges. Non-reversible DEP forces or asymmetric magnitudes for the highly and low-conductive spheres in large areas of the chamber indicate the presence of higher-order moments, mirror charges, etc.

Thyroid hormones, their metabolites and synthetic analogues are potential anti-steatotic drug candidates considering that subclinical and manifest hypothyroidism is associated with hepatic lipid accumulation, non-alcoholic fatty liver disease, and its pandemic sequelae. Thyromimetically active compounds stimulate hepatic lipogenesis, fatty acid beta-oxidation, cholesterol metabolism and metabolic pathways of glucose homeostasis. Many of these effects are mediated by T3 receptor β1-dependent modulation of transcription. However, rapid non-canonical mitochondrial effects have also been reported, especially for the metabolite 3,5-diiodothyronine (3,5-T2), which does not elicit the full spectrum of “thyromimetic” actions inherent to T3. Most preclinical studies in rodent models of obesity and first human clinical trials are promising with respect to the antisteatotic hepatic effects, but potent agents exhibit unwanted thyromimetic effects on the heart and/or suppress feedback regulation of the hypothalamus-pituitary-thyroid-periphery axis and the fine-tuned thyroid hormone system. This review focusses on 3,5-T2 effects on hepatic lipid and glucose metabolism and (non-)canonical mechanisms of action including its mitochondrial targets. Various high fat diet animal models with distinct thyroid hormone status indicate species- and dose-dependent efficiency of 3,5-T2 and its synthetic analogue TRC150094. No convincing evidence has been presented for their clinical use in prevention or treatment of obesity and related metabolic conditions.

This paper presents a robust and efficient fault detection and diagnosis framework for handling small faults and oscillations in synchronous generator (SG) systems. The proposed framework utilizes the Brunovsky form representation of nonlinear systems to mathematically formulate the fault detection problem. A differential-flatness model of SG systems is provided to meet the conditions of the Brunovsky form representation. A combination of high-gain observer and group method of data handling neural network is employed to estimate the trajectory of the system and to learn/ approximate the fault and uncertainties associated functions. The fault detection mechanism is developed based on output residual generation and monitoring so that any unfavourable oscillation and/or fault occurrence can be detected rapidly. Accordingly, an average L1-norm criterion is proposed for rapid decision making of faulty situations. The performance of the proposed framework is investigated for two benchmark scenarios which are actuation fault and fault impact on system dynamics. The simulation results demonstrate the capacity and effectiveness of the proposed solution for rapid fault detection and diagnosis in SG systems in practice, and thus enhancing service maintenance, protection, and life cycle of SGs.

We discuss what we believe could be an improvement in future discussions of the ever-changing brain. We do so by distinguishing different types of brain variability and outlining methods suitable to analyse them. We argue that, when studying brain and behaviour data, classical methods such as regression analysis and more advanced approaches both aim to decompose the total variance into sensible variance components. In parallel, we argue that a distinction needs to be made between innate and acquired brain variability. For varying high-dimensional brain data, we present methods useful to extract their low-dimensional representations. Finally, to trace potential causes and predict plausible consequences of brain variability, we discuss how to combine statistical principles and neurobiological insights to make associative, explanatory, predictive, and causal enquires; but cautions are needed to raise association- or prediction-based neurobiological findings to causal claims.

In France, the regional airport’s demand for services is facing challenges due to the continuous expansion of the high-speed train, high-speed line, and highway networks. This study focuses on the viability of regional airports in France through technical efficiency using data envelopment, principle component analysis, Malmquist productivity index, and regression analysis using bootstrapping. To face the current competitive environment, the regional airports in France adopted strategies, such as the construction of low-cost carrier (LCC) dedicated terminals (LCCTs) with lower expenses to attract more LCCs, increasing non-aeronautical revenue, and hosting regional hubs of LCCs. This is the first study that analyzes all of the French regional airports. The findings indicate that the existence of LCCTs positively affects technical efficiency on the airport’s performance, and share of LCCs at a regional airport leads to neither the efficiency nor the profit level.

Abstract: Mass spectrometry research laboratories reported multiple probes for ambient ionization in the last years. Combining them with a mechanical moving stage enables automated sampling and imaging applications. We developed a robotic platform, which is based on RepRap 3D-printer components, and therefore easy to reproduce and to adopt for custom prototypes. The minimal step width of the Open LabBot is 12.5 μm, and the sampling dimensions (x, y, z) are 18 × 15 × 20 cm. Adjustable rails in an aluminium frame construction facilitate the mounting of additional parts such as sensors, probes, or optical components. The Open LabBot uses industry-standard G-code for its control. The simple syntax facilitates the programming of the movement. We developed two programs: 1) LABI-Imaging, for direct control via a USB connection and the synchronization with MS data acquisition. 2) RmsiGUI, which integrates all steps of mass spectrometry imaging: The creation of G-code for robot control, the assembly of imzML files from raw data and the analysis of imzML files. We proved the functionality of the system by the automated sampling and classification of essential oils with a PlasmaChip probe. Further, we performed an ambient ionization mass spectrometry imaging (AIMSI) experiment of a lime slice with laser desorption low-temperature plasma (LD-LTP) ionization, demonstrating the integration of the complete workflow in RmsiGUI. The design of the Open LabBot and the software are released under open licenses to promote their use and adoption in the instrument developers’ community.

Spent nuclear fuel and high-level radioactive waste can be disposed in deep horizontal drillholes in sedimentary, metamorphic, or igneous rocks. Horizontal drillhole disposal has safety, operational, and economic benefits: The repository is deep in the brine-saturated zone far below aquifers in a reducing environment of formations that can be shown to have been isolated from the surface for millions of years; its depth provides safety against inadvertent intrusion, earth¬quakes, and near-surface perturbations; it can be placed close to the reactors and interim storage facilities, minimizing transportation; disposal costs per ton of waste can be kept substantially lower than for mined repositories by its smaller size, reduced infrastructure needs, and staged imple¬mentation; and, if desired, the waste could be retrieved using “fishing” technology. In the proposed disposal concept, corrosion-resistant canisters containing unmodified fuel assemblies from commercial reactors would be placed end-to-end in up to 50 cm diameter horizontal drill¬holes, a configuration that reduces mechanical stresses and keeps the temperatures below the boiling point of the brine. Other high-level wastes, such as capsules containing 137Cs and 90Sr, can be disposed in small-diameter drillholes. We provide an overview of this novel disposal concept and its technology, discuss some of its safety aspects, and compare it to mined repositories and the deep vertical borehole disposal concept.

Soil-transmitted helminthiasis (STH), a neglected tropical disease (NTD) remains a major health problem all over the world including Ghana, which has STH prevalence of 25.4%. To control the disease, the government of Ghana currently concentrates on implementing mass drug administration (MDA) efforts focusing only among school-aged children. However, various studies have suggested that focusing on only a specific group for MDA may not be cost-effective. Moreover, some adults such as teachers and school-workers spend large fraction of their time with children, who shed more parasite in environment due to unhygienic behavior, and thus have a higher risk of getting infected as compared to other adults. In this study we use a mathematical model to evaluate age-structured and risk-based policies for implementing MDA while capturing transmission dynamics of STH in Ghana. A cost model was developed that included various costs related to MDA to study cost-effectiveness of current policies of MDA in Ghana against novel policies to control STH in Ghana. We carry out analysis for five different scenarios— I: no MDA (baseline), II: current MDA policy (focusing children) in Ghana, III: MDA for different age groups (adults and children groups) for unlimited budget, IV: MDA for different age groups with limitations of number of individuals treated, and, V: MDA for different groups based on their risk of getting infected (adults school workers (high-risk group), adults non-school workers and children groups). Our results suggest that it might be more cost-effective to allocate treatment through MDA to at least some proportion of adults along with children. In case of unlimited budget, the best strategy in Scenario IV would be to treat approximately 22% of adults and approximately 45% of children. The most cost-effective among the 5 scenarios is suggested through scenario V, where high-risk adults group and children are provided MDA at higher level than low-risk adults. In conclusion, age-structured and risk-based allocation of treatment and resources is crucial to reducing STH load in developing countries.

Imaging living cells by atomic force microscopy (AFM) promises not only high-resolution topographical data, but additionally, mechanical contrast, which are not obtainable with other microscopy techniques. Such imaging is however challenging, as cells need to be measured with low interaction forces to prevent either deformation or detachment from the surface. Off-resonance modes which periodically probe the surface have been shown to be advantageous, as they provide excellent force control combined with large amplitudes, which help reduce lateral force interactions. However, the low actuation frequency in traditional off-resonance techniques limits the imaging speed significantly. Using photothermal actuation, we probe the surface by directly actuating the cantilever. Due to the much smaller mass that needs to be actuated, the achievable measurement frequency is increased by two orders of magnitude. Additionally, photothermal off-resonance tapping retains the precise force control of conventional off-resonance modes and is therefore well suited to gentle imaging. Here we show how photothermal off-resonance tapping can be used to study live cells by AFM. As an example of imaging mammalian cells, the initial attachment, as well as long term detachment of a human thrombocytes are presented. The membrane disrupting effect of the antimicrobial peptide CM-15 is shown on the cell wall of E. coli. Finally, the dissolution of the cell wall of B. subtilis by lysozyme is shown. Taken together, these evolutionarily disparate forms of life exemplify the usefulness of PORT for live cell imaging in a multitude of biological disciplines.

When extract building from high resolution remote sensing image with meter/sub-meter accuracy, the shade of trees and interference of roads are the main factors of reducing the extraction accuracy. Proposed a Bayesian Convolutional Neural Networks(BCNET) model base on standard fully convolutional networks(FCN) to solve these problems. First take building with no shade or artificial removal of shade as Sample-A, woodland as Sample-B, road as Sample-C. Set up 3 sample libraries. Learn these sample libraries respectively, get their own set of feature vector; Mixture Gauss model these feature vector set, evaluate the conditional probability density function of mixture of noise object and roofs; Improve the standard FCN from the 2 aspect:(1) Introduce atrous convolution. (2) Take conditional probability density function as the activation function of the last convolution. Carry out experiment using unmanned aerial vehicle(UVA) image, the results show that BCNET model can effectively eliminate the influence of trees and roads, the building extraction accuracy can reach 97%.

A home-built equipment will be presented able to measure thermal expansion and indentation up to 1100 oC. The principle of operation is similar to that of Rockwell hardness measurement. First, we apply a small load and measure the thermal expansion of the construction consisting of the sample holder quartz tube, the conical in-denter and the sample. Then we repeat the thermal cycle with such a high load that produces a deviation in thermal expansion already after 200-300 oC, compared to the previous thermal expansion measurement with low load. With increasing temperature, the indentation depth increases and at higher temperatures we already notice a contraction. The evolution of indentation depth as a function of temperature, d(T), we can obtain by sub-tracting the high load curve from the low load curve. Newly created phenomenological expressions will be tested to describe the thermal softening of pure metals and refractory HEAs. The results will be interpreted taking into account the allotropic transformations and temperature dependencies of elastic moduli. We are working on the instrument to extend the working temperature up to 1200 oC.

This paper presents the theory, design, and application of a dual-branch series-diode analog pre-distortion (APD) linearizer to improve the linearity and efficiency of a K-band high power amplifier (HPA). A first-of-its-kind, frequency-dependent large-signal APD model is presented. This model is used to evaluate different phase relationships between the linear and nonlinear branches, suggesting independent gain, and phase expansion characteristics with this topology. This model is used to assess the impact of diode resistance, capacitance, and ideality factor on the APD characteristics. This feature is showcased with two similar GaAs diodes to find the best fit for the considered HPA. The selected diode is characterized and modeled between 1-26.5 GHz. A comprehensive APD design and simulation workflow is reported. Before fabrication, the simulated APD is evaluated with the measured HPA to verify linearity improvements. The APD prototype achieves a large signal bandwidth of 6 GHz with 3 dB gain expansion and 8∘ phase rotation. This linearizer is demonstrated with a 17-21 GHz GaN HPA with 41 dBm output power and 35 % efficiency. Using a wideband 750 MHz signal, this APD improves the noise power ratio (NPR) by 6.5-8.2 dB over the whole HPA bandwidth. Next, the HPA output power is swept to compare APD vs. power back off for the same NPR. APD improves the HPA output power by 1-2 W and efficiency by approximately 5-9 % at 19 GHz. This efficiency improvement decreases by only 1-2 % when including the APD post-amplifier consumption, thus suggesting overall efficiency and output power improvements with APD at K-band frequencies.

Developing new antibiotics poses a significant challenge in the fight against antimicrobial resistance (AMR), a critical global health threat responsible for approximately 5 million deaths annually. Finding new classes of antibiotics that are safe, have acceptable pharmacokinetic properties, and are appropriately active against pathogens is a lengthy and expensive process. Therefore, high-throughput platforms are needed to screen large libraries of synthetic and natural compounds. In this review, we present bacterial cytological profiling (BCP) as a rapid, scalable, and cost-effective method for identifying the mechanisms of action of antibiotics, offering a promising tool for combating AMR and drug discovery. We present the application of BCP for different bacterial organisms and different classes of antibiotics and discuss BCP's advantages, limitations, and potential improvements. Furthermore, we highlight the studies that have utilized BCP to investigate pathogens listed in the Bacterial Priority Pathogens List 2024 and we identify the pathogens whose cytological profiles are missing. Lastly, we explore the most recent artificial intelligence and deep learning techniques that could enhance the analysis of data generated by BCP, potentially advancing our understanding of antibiotic resistance mechanisms and the discovery of novel druggable pathways.

This study investigates the effect of oil viscosity on pollutant emissions and fuel consumption of an internal combustion engine (ICE) in high-altitude using Response Surface Methodology (RSM). A Chevrolet Corsa Evolution 1.5 SOHC gasoline engine was used in Cuenca, Ecuador (2560 meters above sea level), testing three lubricating oils with kinematic viscosities of 9.66, 14.08, and 18.5 cSt under various engine speeds and loads. Key findings include: hydrocarbon (HC) emissions were minimized to 7.25 ppm with low viscosity and load; carbon dioxide (CO2) emissions peaked at 15.2% vol with high viscosity and load; carbon monoxide (CO) ranged from 0.04% to 3.74% depending on viscosity and load; nitrogen oxides (NOx) were significantly influenced by viscosity, RPM, and load, indicating a need for model refinement; and fuel consumption was significantly affected by load and viscosity. RSM-based optimization identified optimal operational conditions with a viscosity of 13 sCt, 1473 rpm, and a load of 78%, resulting in 52.35 ppm of HC, 13.97% vol of CO2, 1.2% vol of CO, 0 ppm of NOx, and a fuel consumption of 6.66 l/h. These conditions demonstrate the ability to adjust operational variables to maximize fuel efficiency and minimize emissions. This study underscores the critical role of optimizing lubricant viscosity and operational conditions to mitigate environmental impact and enhance engine performance in high-altitude environments.

According to many research groups, high glucose induces over production of superoxide anions, and reactive oxygen species (ROS) in general is the link between high glucose levels and the toxicities seen at cellular levels. Respiratory complex anomalies could lead to the production of ROS. Calcium [Ca2+], at physiological levels serves as a second messenger in many physiological functions. Accordingly, mitochondrial calcium [Ca2+]m overload leads to ROS production which could be lethal to the mitochondria through various mechanisms. The F1F0-ATPase (ATP syn-thase or complex V) is the enzyme that is responsible for catalyzing the final step of oxidative phosphorylation. It does so by coupling the translocation of protons in the mitochondrial in-termembrane space and shuttling them to the mitochondrial matrix for ATP synthesis to take place. Mitochondrial complex V T8993G mutation specifically blocks the translocation of protons across the intermembrane space thereby blocking ATP synthesis leading to Neuropathy, Ataxia and Retinitis Pigmentosa Syndromes (NARP). This study seeks to explore the possibility of [Ca2+]m overload mediating the pathological roles of high glucose in defective respiratory chain mediated mitochondrial stress. The NARP cybrids are the in vitro experimental models for the cells with F1FO-ATPase defects, these cells harbor 98% of mtDNA T8993G mutation. Their coun-terparts 143B osteosarcoma cell lines are the parental cell lines used for comparisons. We uncov-ered that, NARP cells mediated and enhanced the death of the cells (apoptosis) when incubated with hydrogen peroxide (H2O2) and high glucose respectively as depicted by the MTT assay of cell viability. Furthermore, using the fluorescence probe-coupled laser scanning confocal imag-ing microscopy, NARP cells significantly enabled mitochondrial reactive oxygen species (mROS) formation and enhanced the depolarization of the mitochondrial membrane potential (ΔΨm). Elucidating the mechanisms of sugar enhanced toxicity on mitochondria would help in the fu-ture to alleviate the symptoms of patients associated with (NARP) syndromes.

In the evolving landscape of pharmaceutical manufacturing, a comprehensive continuous production process is being crafted for small-scale active pharmaceutical ingredient production. This study focuses on continuous crystallization with separate nucleation and crystal growth units, as well as continuous downstream processing, encompassing filtration, washing, and drying until the formation of free-flowing particles. We introduce a novel continuous nucleator designed based on solubility data and produced via 3D printing, enabling a fast and precise small-scale manufacturing of a nucleator meeting the requirements for nucleation and for the further growth processes. The nucleator was evaluated with regard to its suitability for continuous long-term operation across various coupled crystallizers. As a practical application example it is connected to a slug flow crystallizer to enable high-quality continuous crystallization. Additionally, the full integration of downstream processes using the continuous vacuum screw filter to achieve free-flowing product particles is realized. Even under non-optimized process conditions, with the help of in-situ generation of nuclei free-flowing product particles were successfully obtained. This is particularly useful during drug development when no material is available for seed addition and quickly obtain product for further characterization.

Thin Pd-40%Cu films were obtained by the classical melting and rolling method, magnetron sputtering and modified with nanostructured functional coatings to intensify the process of hydrogen transport. The films were modified by electrodeposition according to the classical method of obtaining palladium black and "Pd-Au nanoflowers" with spherical and pentagonal particles, respectively. The experiment results demonstrated the highest catalytic activity (89.47 mA cm–2), good resistance to CO poisoning and long-term stability of Pd-40%Cu films with a pentagonal structured coating. The investigation of the developed membranes in the hydrogen transport processes in the temperature range of 25-300°C also demonstrated high and stable fluxes up to 475.28 mmol s–1 m–2 (deposited membranes) and 59.41 mmol s–1 m–2 (dense-metal membranes), which turned out to be up to 1.5 higher compared to membrane materials with classic niello. For all-metal modified membranes, the increase in flux was up to 7 times, compared with a smooth membrane made of pure palladium, and for deposited films, this difference was several tens of times. The membrane materials selectivity was also high up to 4419. The developed strategy for modifying membrane materials with functional coatings of a fundamentally new complex geometry can shed new light on the development and fabrication of durable and highly selective palladium-based membranes for gas steam reformers.

Nucleic acid therapeutics are witnessing an impressive acceleration in recent years. They work through multiple mechanisms of action, including downregulation of gene expression and modulation of RNA splicing. While several drugs based on the former mechanism have been approved, few target the latter, despite the promise of RNA splicing modulation. To improve our ability to discover novel RNA splicing-modulating therapies, we developed HCS-Splice, a robust cell-based High-Content Screening (HCS) assay. By implementing the use of a two-colour (GFP/RFP) fluorescent splicing reporter plasmid, we developed a versatile, effective, rapid, and robust high-throughput strategy for the identification of potent splicing-modulating molecules. The HCS-Splice strategy can also be used to functionally confirm splicing mutations in human genetic disorders or to screen drug candidates. As a proof-of-concept, we introduced a dementia-related splice-switching mutation in Microtubule-Associated Protein Tau (MAPT) exon 10 splicing reporter. We applied HCS-Splice to the wild-type and mutant reporters and measured the functional change in exon 10 inclusion. To demonstrate the applicability of the method to cell-based drug discovery, HCS-Splice was used to evaluate the efficacy of an exon 10-targeting siRNA, which was able to restore the correct alternative splicing balance.

Patients with pT1 high-grade (HG) bladder cancer (BC) and a very high risk of progression might benefit from immediate radical cystectomy (RC), but this option remains controversial. Validation of a standardized method to evaluate the extent of lamina propria (LP) invasion (with recognized prognostic value) in transurethral resections (TURBT) specimens is still needed. The Rete Oncologica Lombarda (ROL) system showed a high predictive value for progression after TURBT in recent retrospective studies. Our aim was to validate ROL system on a large mono-institutional prospective series of primary urothelial carcinomas. From 2016 to 2020, we adopted ROL for all patients with pT1 HG BC on TURBT. We employed a 1.0-mm threshold to stratify tumors in ROL1 and ROL2. A total of 222 pT1HGBC were analyzed. Median age was 74 years, with male predominance (73.8%). ROL was feasible in all cases: 91 cases were ROL1 (41%) and 131 ROL2 (59%). At a median follow up of 26.9 months (IQR 13.8-40.6), we registered 80 recurrences and 40 progressions. ROL was a significant predictor of tumor progression at both univariable (HR 3.53; CI 95% 1.56 – 7.99; p&lt;0.01) and multivariable (HR 2.90; CI 95% 1.25 – 6.75; p=0.01) Cox regression analyses. At Kaplan-Meier estimates, ROL showed correlation with both PFS (p=0.0012) and RFS (p=0.0167). Our results confirmed the strong predictive value of ROL for progression on a large prospective series. We encourage the application of ROL for reporting the extent of LP invasion, substaging T1 HG BC, and improving risk tables for urological decision making.

This article investigated the Automatic Generation Control(AGC) of multi-area multi-source interconnected systems with hydropower plants, thermal power plants, and wind energy. Adaptive Neuro-fuzzy controller integrated with the cascaded proportional-integral-derivative with filter (PIDF-PIDF) is a new cascaded controller (ANF-PIDF-PIDF) that has been presented as a secondary controller for applied hybrid power systems. The recent Skill Optimization Algorithm (SOA) is employed to optimize PIDF- PIDF controller parameter gains and the Adaptive Neuro-Fuzzy controller's inputs and output scaling factors. SOA is used to update the controller parameters with integral square error (ISE) employed as the objective function. A 1% step load disturbance was considered simultaneously in all three areas. The controller's performance is evaluated and compared with and without considering the effects of wind energy sources and non-linearity for ANF-PIDF-PIDF, PIDF-PIDF, and PIDF and it was determined that the ANF-PIDF-PIDF was the most efficient. The dynamic system performance is also compared with parallel high voltage direct current (HVDC) tie-lines. The investigation clearly shows that incorporating HVDC tie-line with multi-area, multi-source provides better dynamic performance in maximum amplitude, oscillation, and settling time. Additionally, sensitivity analysis is done and the optimum controller gains does not need to be reset to uncertain values in system loading conditions. All simulation results were evaluated using MATLAB 2016b.

Human exposure to infectious aerosols results a transmission of diseases, such as influenza, tuberculosis, and COVID-19. Most dental procedures generate a significant number of aerosolized particles, increasing transmission risk in dental settings. Since the generation of aerosols in dentistry is unavoidable, many clinics started using intervention strategies such as area-filtration units and extraoral evacuation equipment, especially under the relatively recent constraints of the pandemics. However, the effectiveness of these devices in dental operatories has not been studied. Therefore, the dental personnel's ability to position and operate such instruments efficiently is also limited. To address these challenges, we utilized a real-time sensor network for assessment of aerosol dynamics during dental restoration and cleaning producers with and without intervention. The strategies tested during the procedures were (i) local area high-efficiency particle air (HEPA) filters and (ii) extra-oral suction device (EOSD). The study was conducted at the University of Washington School of Dentistry using a network of thirteen fixed sensors positioned within the operatory and one wearable sensor worn by the dental operator. The sensor network provides time and space-resolved particulate matter (PM) data. Three-dimensional (3D) visualization informs aerosol persistence in the operatory. It was found that area filters did not improve the overall aerosol concentration in dental offices significantly. An average of 16% decrease in PM concentration was observed when EOSD equipment was used during the procedures. The combination of real-time sensors and 3D visualization can provide dental personnel and facility mangers with actionable feedback to effectively assess aerosol transmission in medical settings and develop evidence-based intervention strategies.

The expression "Follow the water" is used in order to recognize inside the universe, life as it exists on Earth. It is shown here that the expression "Follow the water in its high-subcritical state" can be used in order to recognize the components of life which form prior to the emergence of life. This specific state of water leaves signatures inside the minerals which are produced during high-subcritical water/rock interaction.

The identification of informal settlements in urban areas is an important step in developing and implementing pro-poor urban policies. Understanding when, where and who lives inside informal settlements is critical to efforts to improve their resilience. This study aims to analyse the capability of machine-learning (ML) methods to map informal areas in Jeddah, Saudi Arabia, using very-high-resolution (VHR) imagery and terrain data. Fourteen indicators of settlement characteristics were derived and mapped using an object-based ML approach and VHR imagery. These indicators were categorised according to three different spatial levels: environ, settlement and object. The most useful indicators for prediction were found to be density and texture measures, (with random forest (RF) relative importance measures of over 25% and 23% respectively). The success of this approach was evaluated using a small, fully independent validation dataset. Informal areas were mapped with an overall accuracy of 91%. Object-based ML as a hybrid approach performed better (8%) than object-based image analysis alone due to its ability to encompass all available geospatial levels.

Forest canopy gaps are important for the ecosystem dynamics. Depending on tree species, small canopy openings might be also associated to intra-crown porosity and to space between crowns. Yet, little is known on the relationships between the fine-scaled pattern of canopy openings and biodiversity features. This research explored the possibility of i)- mapping forest canopy gaps from a very high resolution orthomosaic (10 cm), processed from a versatile imaging platform such as unmanned aerial vehicles (UAV), ii)- to derive patch metrics that can be tested as covariates of variables of interest for forest biodiversity monitoring. This is attempted in a test area of 240 ha covered by temperate deciduous forest types in Central Italy and containing 50 forest inventory plots of about 530 m². Correlation and linear regression techniques were used to explore relationships between patch metrics and understorey (density, development and species diversity) or forest habitat biodiversity variables (density of micro-habitat bearing trees, vertical species profile, tree species diversity). The results revealed that small openings in the canopy cover (75% smaller than 7 m²) can be faithfully extracted from UAV RGB imagery, using the red band and contrast split segmentation. Highest correlations were observed in the mixed forest (beech and turkey oak), while beech forest had the poorest ones and turkey oak forest displayed intermediate results. Moderate to strong linear relationships were found between gap metrics and understorey variables in mixed forest type, with adjusted R² from linear regression ranging from 0.52 to 0.87. Equally good results, in the same forest types, were observed for forest habitat biodiversity variables (0.52<adjusted R²<0.79) with highest values found for density of trees with microhabitats and vertical species profile. In conclusion, this research highlights that UAV remote sensing can potentially provide covariate surfaces of variables of interest for forest biodiversity monitoring, conventionally collected in forest inventory plots. By integrating the two sources of data, these variables can be mapped over small forest areas with satisfactory levels of accuracy, at a much higher spatial resolution than would be possible by field-based forest inventory solely.

One mechanism by which fructose could exert deleterious effect in metabolism and inflammation is via its potency vis-à-vis de Maillard reaction. We employed simulated stomach and duodenum digestion of ovalbumin to test the hypothesis that indeed AGEs are formed by fructose during simulated digestion of an ubiquitous food protein with intrinsic allergenic potential and under model physiological conditions. Methods: OVA was subjected to simulated gastric and intestinal digestion using standard models, in presence of fructose or glucose (0-100 mM). Peptide fractions were analyzed by fluorescence spectroscopy and intensity at Excitation: λ370 nm, Emission: λ 440nm. Results: AGE adducts form between fructose and OVA which can be found in peptide fractions (< 5 kDa) at times (30 min) and concentration ranges (10 mM) plausibly found in the intestines, whereas no reaction occurs with glucose. The reaction is inhibited by chlorogenic acid at concentrations compatible with those found in the gut. The reaction is inhibited by AG, a specific antiglycation agent. Conclusion: Our proof of principle study shows that fructose-AGE formation on an ubiquitous allergenic protein indeed occurs in one hour and thereby may pave the way for the study of yet another mechanism by which the excess fructose in our Western diets is contributing to disease: intestinal AGE formation, absorption and RAGE engagement.

This study describes the properties of high-T_c cuprates by introducing rotating holes that are created by angular momentum conservations on a 2D CuO₂ surface, and which have a different mass from that of a normal hole because of the magnetic field energy induced by the rotation. This new particle called a macroscopic Boson describes the doping dependences of pseudo-gap temperature and the transition temperature at which an anomaly metal phase appears and describes the origin of the pseudo-gap. Furthermore, this study introduces a new model to handle many-body interactions, which results in a new statistic equation. This statistic equation describing many-body interactions accurately explains why high-T_c cuprates have significantly high critical temperatures. Moreover, a partition function of macroscopic Bosons describes the properties of anomaly metal phase, which sufficiently agree with experiments. Note that, the calculations were conducted, using the result from our previous study that analytically describes the doping dependence of T_c. By introducing a macroscopic Boson and the new statistical model for many-body interactions, this study uncovered the mystery of high- T_c cuprates, which have been a challenge for many researchers. An important point is that, in this study, pure analytical calculations are consistently conducted, which agree with experimental data well (i.e., they do not use numerical calculations or fitting methods but use many actual physical constants).

Dynamic wireless charging (DWC) for electric vehicles (EVs) is gaining traction as a more accessible charging method, with the added benefits of extending vehicle range and reducing battery size. By providing a charging connection through the road surface, DWC offers an additional charging option without the need for a physical connection. This approach inherently links the charging load profile to the vehicle's movement relative to the charging pad(s), thus introducing more stochastic charging events to the grid. For dynamic wireless power transfer (DWPT), these events involve high instantaneous power and are short in duration. To better understand the impact of DWPT, accurate models are required to test control systems and potential solutions. Additionally, these systems require high-frequency simulation for wireless power transfer (WPT), which results in long simulation times during development. In this paper, a simplified model is presented to ensure the efficiency of grid-connected simulations and achieve a certain level of accuracy that reflects the internal dynamics of wireless charging. This model achieves a 30-fold reduction in simulation time with only a 6% deviation from the base model.

Previous research has indicated that ultra-high pressure (UHP) technology is useful in speeding up the extraction process of cold brew (CB) coffee. However, the impact of different degrees of roasting on UHP CB coffee is still unclear. Therefore, this study aimed to investigate the effects of three different degrees of roasting (light, medium, and dark) on the physicochemical and flavor characteristics of UHP CB coffee. The results of this study showed that most physicochemical characteristics of UHP coffee were similar to those of conventional CB coffee, regardless of the degree of roasting. However, the majority of physicochemical characteristics, non-volatile components, and sensory evaluation significantly increased with an increase in roasting degree. The HS-SPME-GC/MS analysis showed that most volatile components, such as pyrazines, furans (except furfural), esters, pyrrole, pyridine, and most aldehydes, increased from light to dark roasting, and this was significantly evident in CB coffee compared with UHP. The content of volatile components in UHP coffee was significantly (P<0.05) higher than that in CB coffee at the same degree of roasting, especially with dark roasting. The combination of orthogonal partial least squares-discriminant analysis (OPLS-DA) and principal component analysis (PCA) indicated that the distance between coffee samples at different degrees of roasting under CB coffee was greater than that under UHP coffee. However, the distance between these two extraction methods at medium roasting was evidently closer than that at light and dark roasting. Moreover, 15 representative differential compounds, such as were Hazelnut pyrazine, linalool, butane-2,3-dione, 3- methylbutanal found by the calculation of odor-active values (OAVs) indicating the main contributing compounds to odor. Overall, the effect of roasting degrees on UHP coffee was less than that on CB coffee, which was consistent with the results of physicochemical characteristics, volatile components, and sensory evaluation.

The effects of chemical composition and solidification rate on the solidification behavior of high-Cr white irons were investigated through directional solidification. Increasing the solidi-fication rate in hypoeutectic alloys caused the finer dendrite arm spacing as expected. The eutec-tic structure which formed in the interdendritic region comprised of M7C3 and austenite, how-ever, secondary dendrite arms of hypoeutectic alloys contained a few M7C3 particles that solidi-fied prior to the eutectic structure. The transition from cellular to dendritic solidification oc-curred at a solidification rate between 50 µm/s and 100 µm/s in a near eutectic alloy. In the near eutectic alloy with cellular solidification, a directionally arrayed in-situ composite of M7C3/austenite formed within the cell. Speckle-like feature appeared in the intercellular region due to M23C6 carbide precipitation during subsequent cooling after freezing. Like dendrite arm spacing in hypoeutectic alloys, the inter-speckle spacing and the inter-fibre spacing became finer with increasing solidification rate in the cellular solidification range.

The production of particles outside the region of nucleon-nucleon kinematics due to interactions involving dense cold clusters of quark-gluon matter in nuclei is calculated. The possibility of observing this process in the region of central rapidities and large transverse momenta in heavy ion collisions at low energies with MPD detector at the NICA collider has been demonstrated.

This review is a first attempt at bringing together various concepts from research on wall- and magnetically-bounded turbulent flows. Brief reviews of both fields are provided: The main similarities identified are coherent (turbulent) structures, flow generation and transport barriers. Examples are provided and discussed.

To enable the deployment of battery-electric vehicles (BEV) as passenger cars in the private transport sector, a suitable charging infrastructure is crucial. In this paper a methodology for efficient spatial distribution of charging infrastructure is evaluated by investigating a scenario with a market penetration of BEVs of 100 percent (around 1.3 million vehicles). It aims towards the development of various charging infrastructure scenarios - including public and private charging - which are suitable to cover the charging demand. Therefore, these scenarios are investigated in detail with focus on number of public charging points, their spatial distribution, the available charging power and the necessary capital costs. For the creation of those charging infrastructure scenarios a placement model is developed. It uses the data of a MATSim (Multi-Agent Transport Simulation) traffic simulation of the metropolitan area of Berlin to evaluate and optimize different distributions of charging infrastructure. The model uses a genetic algorithm and the principle of multi-objective optimization. The capital cost of the charging points and the mean detour car drivers must cover additionally are used as optimization criteria. Using these criteria should lead to cost efficient infrastructure solutions which provide high usability at the same time. The main advantage of the method selected is that multiple optimal solutions with different characteristics can be found and suitable solutions can be selected by using other criteria subsequently. The optimized charging infrastructure solutions show capital costs between 624 and 2950 million euro. Users must cover an additionally mean detour of 254m to 590m per charging process to reach an available charging point. According to the results a suitable ratio between charging points and vehicles is between 11:1 and 5:1. A share of fast charging infrastructure (&gt;50kW) of less than ten percent seems to be sufficient, if it is situated at main traffic routes and highly frequented places.

At INFN-LNS, and in collaboration with the ATOMKI laboratories, an innovative multi-diagnostic system with advanced analytical methods has been designed and implemented. This is based on several detectors and techniques (Optical Emission Spectroscopy, RF systems, Interfero-polarimetry, X-ray detectors) and here we focus on high resolution spatially-resolved X-ray spectroscopy, performed by means of a X-ray pin-hole camera setup operating in the 0.5−20 keV energy domain. The diagnostic system was installed at a 14 GHz Electron Cyclotron Resonance (ECR) ion source (ATOMKI, Debrecen), enabling high precision X-ray spectrally-resolved imaging of ECR plasmas heated by hundreds of Watts. The achieved spatial and energy resolution were 0.5 mm and 300 eV at 8 keV, respectively. We here present the innovative analysis algorithm that we properly developed for obtaining Single Photon-Counted (SPhC) images providing the local plasma emitted spectrum in a High-Dynamic-Range (HDR) mode, by distinguishing fluorescence lines of the materials of the plasma chamber (Ti, Ta) from plasma (Ar). This method allows a quantitative characterization of warm electrons population in the plasma (and its 2D distribution) which are the most important for ionization, and also to estimate local plasma density and spectral temperatures. The developed post-processing analysis is also able to remove the readout noise, that is often observable at very low exposure times (msec). The setup is now under update including fast shutters and trigger systems in order to allow simultaneously space and time-resolved plasma spectroscopy during transients, stable and turbulent regimes.

The article presents results of research consisting in an attempt to assess the influence of temperature, heating time and cooling method on microstructure and residual strength properties of steel previously tempered during the production process. Simulated environmental conditions to which high-strength bolts, commonly used in steel construction, were subjected, were intended to reflect conditions of a natural fire that may occur in public facilities where the obligation to ensure safety of users and rescue teams is of key importance, also required by law. Furthermore, the tests carried out also comprised a simulated effect of a rescue and firefighting operation using shock, rapid cooling of some of the heated bolts. Samples cut out from the tested bolts, after they were properly prepared, were subjected to microstructural tests using light microscopy, scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), phase analysis with the use of an X-ray diffractometer (XRD) and quantitative analysis of the microstructure involving, inter alia, measuring the surface area of grains, their equivalent diameter and mean diameter. As a result of the tests, considerable microstructure changes were identified occurring in the bolt material as a result of exposing it to fire conditions, leading to a change in key, from the point of view of structural safety, mechanical properties. The results of the microstructure tests were compared with the results of previous strength tests, including hardness of the material after the heat treatment and the residual tensile strength of the material Rm. A conducted comparative analysis showed a significant effect of all such factors as the temperature level of the simulated fire, its duration and the fire-fighting method on the mechanical properties of bolts. Results obtained were provided with required comments and the concept of using the microstructure for the post-fire assessment of steel structures was referred to.

The rapid expansion of transcriptomics from increased affordability of next-generation sequencing (NGS) technologies generates rocketing amounts of gene expression data across biology and medicine, and notably in cancer research. Concomitantly, many bioinformatics tools were developed to streamline gene expression analysis and quantification. We tested the concordance of NGS RNA sequencing (RNA-seq) analysis outcomes between the two predominant programs for reads alignment, HISAT2 and STAR, and the two most popular programs for quantifying gene expression in NGS experiments, edgeR and DESeq2, using RNA-seq data from a series of breast cancer progression specimens, which include histologically confirmed normal, early neoplasia, ductal carcinoma in situ and infiltrating ductal carcinoma samples microdissected from formalin fixed, paraffin embedded (FFPE) breast tissue blocks. We identified significant differences in aligners’ performance: HISAT2 was prone to misalign reads to retrogene genomic loci, STAR generated more precise alignments, especially for early neoplasia samples. edgeR and DESeq2 produced similar lists of differentially expressed genes in stage comparisons, with edgeR producing more conservative, though shorter, lists of genes. Albeit, Gene Ontology (GO) enrichment analysis revealed no skewness in significant GO categories identified among differentially expressed genes by edgeR vs DESeq2. As transcriptome analysis of archived FFPE samples becomes a vanguard of precision medicine, identification and fine-tuning of bioinformatics tools becomes critical for clinical research. Our results indicate that STAR and edgeR are well-suited tools for differential gene expression analysis from FFPE samples.

This paper identifies a criterion for choosing the largest set of rejected hypotheses in high-dimensional data analysis where Multiple Hypothesis testing is used in exploratory research to identify significant associations among many variables. The method neither requires predetermined thresholds for level of significance, nor uses presumed thresholds for false discovery rate. The upper limit for number of rejected hypotheses is determined by finding maximum difference between expected true hypotheses and false hypotheses among all possible sets of rejected hypotheses. Methods of choosing a reasonable number of rejected hypotheses and application to non-parametric analysis of ordinal survey data are presented.

We extensively studied serigraphic screen-printed commercial silver flake inks loaded with silicon inclusions in order to achieve pinning at the grain boundaries. Based on grain size measurements using electron backscattered diffraction (EBSD), commercial silver ink with silicon microparticle content of 5 wt.% shows a significant grain growth retardation compared to the pristine silver ink, which stabilizes electrical conductivity up to 700 ◦C via Zener pinning mechanism. The modified silicon-loaded silver ink experiences a two times increase in grain size when heated up to 700 ◦C, compared to a seven times increase for the pristine silver ink. In turn, this enables operation temperatures significantly higher than the conventional operational window of microparticle-based silver inks, which are usually limited to 400 ◦C. Using isothermal exposures of 10 minutes up to 4 hours this phenomenon is observed at temperatures ranging from 250 ◦C to 900 ◦C. The electrical conductivity stability, grain size evolution and oxide contents were studied up to 4 hours. The activation energy of silver ink with silicon inclusions is 54% lower than for the pristine silver ink due to pining effect, which retards grain growth via the Zener mechanism. Most importantly, the electrical resistivity becomes stable up to 700 ◦C, which is more than twice the operation limit for off-the-shelf screen-printable silver flake inks. Hence, we demonstrate that adding controlled amounts of silicon particles to silver inks towards grain structure engineering can open new vistas of possibilities for screen-printed metallic inks.

High-Level Synthesis (HLS) tools have revolutionized FPGA application development by providing a more efficient and streamlined approach, significantly impacting digital design methodologies. Despite the capability of FPGAs to customize numerical representations in data paths, most HLS projects have focused on fixed-point precision, while floating-point representations remain limited to vendor-provided single, double, and half-precision formats. This paper proposes a customized floating-point library compatible with HLS to address these limitations. This library allows programmers to define the number of exponent and mantissa bits at compile time, providing greater flexibility and enabling the use of mixed precision. Moreover, this library includes optimized implementations of common components such as vector summation (VSUM), dot-product (DP), and matrix-vector multiplication (MVM). Results demonstrate that the proposed library reduces latency and resource utilization compared to vendor IP blocks, particularly in VSUM, DP, and MVM operations. For example, the MVM operation involving a 32x32 matrix, using vendor IP requires 22 clock cycles, whereas CuFP completes the same task in just 7 clock cycles, using approximately 60% fewer DSPs, 10% fewer LUTs, and 60% fewer FFs.

Understanding speech in noise is particularly difficult for individuals occupationally exposed to noise due to a to a mix between noise-induced auditory lesions and energetic masking of speech signal. For years, the monitoring of conventional audiometric thresholds has been the usual way to check and preserve the auditory function. But the highlighting of supra-threshold deficits, notably speech in noise understanding difficulties, has pointed out the need for new monitoring tools. The present study aims to identify the most important variables that predict speech in noise under-standing in order to suggest a new way of regular monitoring. Physiological (distortion products of otoacoustic emissions, electrocochleography) and behavioral (amplitude and frequency modula-tion detection thresholds, conventional and extended high frequency audiometric thresholds) variables were collected in a population of individuals presenting a relative homogeneous occu-pational noise exposure. Those variables were used as predictors in a statistical model (random forest) to predict scores of three different speech in noise tests and a self-report of speech in noise ability. The extended high frequency threshold appears to be the best predictor and therefore an interesting candidate for a new way of monitoring noise exposed professionals.

This research paper focuses on the synthesis and characterization of Cu-doped Mg-Co ferrites with varying compositions (Mg_0.6-xCo_0.4Cu_xFe₂O₄, where x = 0.0, 0.1, 0.2, and 0.3) using a solid-state reaction method. This paper also investigates the structural, morphological, magnetic, and electrical characteristics of synthesized Mg_0.6-xCo_0.4Cu_xFe₂O₄, where x = 0.0, 0.1, 0.2, and 0.3. The X-ray diffraction (XRD) technique confirms the ferrites spinel structure in the Fd-3m space group, with average crystallite sizes ranging from 57.29 to 48.57 nm. Fourier Transform Infrared (FTIR) spectroscopy verifies chemical and structural changes, while scanning electron microscopy (SEM) reveals cubic crystal growth with an average grain size of 1 to 1.5 μm. DC electrical resistivity decreases with increasing temperature and Cu²⁺ substitution, ranging from 1.4 x 10⁶ Ω-cm to 6.7 x 10⁵ Ω-cm. The study suggests a correlation between resistivity and Cu²⁺ concentration. Magnetic behaviour, studied using a Vibrating Sample Magnetometer (VSM), shows dependence on dopant concentration, with coercivity ranging from 157 Oe to 256 Oe. The results indicate potential applications in magnetic storage devices, antennas, transformers, and high-frequency electronics.

Product introductions play a pivotal role in the success and competitiveness of manufacturing, particularly in the context of new product development. Low-volume manufacturing companies exhibit distinct characteristics that significantly influence the product introduction process. Notably, the quality of information exchange between product design and production interfaces becomes paramount in this high-mix and low-volume industry. Consequently, there exists a pressing need to explore various methods for adapting and customizing management mechanisms and strategies to align with the unique requirements and characteristics of low-volume manufacturing and its associated product introduction processes. While the need for this knowledge is critical in the context of low-volume manufacturing, a majority of existing studies predominantly focus on the management aspects within high-volume manufacturing. Therefore, the primary aim of this study is to investigate the customization of product introduction management strategies to enhance the quality of information content within the realm of low-volume manufacturing. Drawing upon a longitudinal analysis of new product introductions within a low-volume manufacturing company, this study narratively elucidates how the examined company implemented product introduction management strategies to facilitate the enhancement of information content quality during the product introduction phase. The study presents its findings on management strategies across three key stages: pre-implementation, post-implementation, and subsequent modification and refinement of strategies following the initial round of implementation. By shedding light on these strategies, this study offers a comprehensive understanding of management approaches in the context of low-volume product introduction. As a result, it makes a valuable contribution to the discourse on information management and interface management in the high-mix, low-volume manufacturing literature.

J/ψ, a charmonium bound state made of a charm and an anti-charm quark, has been discovered in the 1970s and confirmed the quark model. Because the mass of charms quarks is significantly above the Quantum Chromodynamics (QCD) scale ΛQCD, charmonia are considered as excellent probes to test perturbative Quantum Chromodynamics (pQCD) calculations. Over the past decades, they have been studied extensively at different high energy colliders. However, their production mechanisms, which involves multiple scales, are still not very well understood. Recently, in high multiplicity p+p collisions at RHIC and at the LHC, a significant enhancement of J/ψ production yield has been observed, which suggests a strong contribution from the Multi-Parton Interaction (MPI). This is different from the traditional pQCD picture where charm quark pairs are produced from a single hard scattering between partons in p+p collisions. In this work, we will report the J/ψ normalized production yield as a function of normalized charged particle multiplicity over a board range of rapidity and event multiplicity in the J/ψ→μ+μ− channel with PHENIX Run 15 p+p data at \sqrt{s}=200 GeV. The results are compared with PYTHIA 8 simulations with the MPI option on and off. Finally, the outlooks of J/ψ in p+Au and Au+p collisions along with Color Glass Condensate (CGC) predictions and of multiplicity dependent ψ(2S)/J/ψ ratio in p+p data will be briefly discussed.

The evaluation of HAADF-STEM images of a sample with the composition Nb18W16O93 provided new insights in its real structure. The basic structure comprises an intact octahedral framework of the tetragonal tungsten bronze (TTB) type. The partial occupation of the pentagonal tunnels (PT) by metal-oxygen strings determines the oxygen to metal ratio (O/SM with M = Nb,W). For a large area, the O/SM was determined to be 2.755 which is smaller than the value of Nb18W16O93 which is O/SM = 2. 735. To a large extent, the threefold TTB superstructure structure of Nb8W9O47 with a high oxygen content is present (O/SM = 2.765). In addition, a new fourfold TTB superstructure was found in small domains: Nb12W11O63 with an O/SM = 2.739 obviously accommodates a part of the sample’s metal excess compared to the stable phase Nb8W9O47.

An effective process monitoring strategy is a requirement for meeting the challenges posed by increasingly complex products and manufacturing processes. To address these needs, this study investigates a comprehensive scheme based on classical machine learning methods, deep learning algorithms, and feature extraction and selection techniques. In a first step, a novel deep learning architecture based on convolutional neural networks (CNN) and gated recurrent units (GRU) is introduced to predict the local weld quality based on mid-wave infrared (MWIR) and near-infrared (NIR) image data. The developed technology is used to discover critical welding defects including lack of fusion (false friends), sagging and lack of penetration, and geometric deviations of the weld seam. Additional work is conducted to investigate the significance of various geometrical, statistical, and spatio-temporal features extracted from the keyhole and weld pool regions. Furthermore, the performance of the proposed deep learning architecture is compared to that of classical supervised machine learning algorithms, such as multi-layer perceptron (MLP), logistic regression (LogReg), support vector machines (SVM), decision trees (DT), random forest (RF) and k-Nearest Neighbors (kNN). Optimal hyperparameters for each algorithm are determined by an extensive grid search. Ultimately, the three best classification models are combined into an ensemble classifier that yields the highest detection rates and achieves the most robust estimation of welding defects among all classifiers studied, which is validated on previously unknown welding trials.

Pieron's and Chocholle’s seminal psychophysical work predicts that human response time to information relative to visual contrast and/or sound frequency decreases when contrast intensity or sound frequency increases. The goal of this study is to bring to the fore the ability of individuals to use visual contrast intensity and sound frequency in combination for faster perceptual decisions of relative depth (“nearer”) in planar (2D) object configurations on the basis of physical variations in luminance contrast. Computer controlled images with two abstract patterns of varying contrast intensity, one on the left and one on the right, preceded or not by a pure tone of varying frequency, were shown to healthy young humans in controlled experimental sequences. Their task (two-alternative forced-choice) was to decide as quickly as possible which of two patterns, the left or the right one, in a given image appeared to “stand out as if it were nearer” in terms of apparent (subjective) visual depth. The results show that the combinations of varying relative visual contrast with sounds of varying frequency exploited here produced an additive effect on choice response times in terms of facilitation, where a stronger visual contrast combined with a higher sound frequency produced shorter forced-choice response times. This new effect is predicted by cross-modal audio-visual probability summation.

In the study at hand a systemic investigation regarding the tribochemical effects of crankcase soot is presented. Sooted oils were generated via an engine dynamometer test. Both conventional as well as advanced oil condition monitoring methods indicated a mild degradation of additives. The wear volume was greatly increased with the sooted oils in model tribometer tests, despite the high residual zinc dialkyl dithiophosphate (ZDDP) antiwear (AW) levels. Once the soot was removed via ultracentrifugation, the wear volume returned to levels comparable to the fresh oil. Surface investigations revealed that ZDDP tribofilms could not form in the sooted oils, as only a thin sulfide layer was present on the metal surfaces. Meanwhile, typical tribofilms were observable with centrifuged oils. The results indicated that a tribocorrosive mechanism is most likely responsible for the elevated wear in the sooted oils, where only the iron sulfide base layer of ZDDP films is formed, which then is rapidly removed by the soot particles in an abrasive manner.

The hospital indoor environment plays a significant role in shaping the microbial exposures that humans encounter. Resistance to antibiotics is one of the mechanisms employed by bacteria to develop resilience against stress in indoor environments. The extensive usage of antibiotics has been a key factor in driving changes in the ecological function of antibiotic resistance genes (ARGs) and their acquisition by pathogenic bacteria. By integrating the 16S rRNA Illumina sequencing and high throughput-qPCR approaches with water and air dust samples across seven departments at Peking University Shenzhen Hospital, China, this study yielded intriguing findings regarding the department-specific variation, transmission, and correlation of bacteria, ARGs and MGEs within the hospital indoor environment. One notable observation was that the seasonal variation played a vital role in shaping the bacterial composition in the overall hospital indoor environment across seven studied departments. Nevertheless, a similar significant seasonal impact was only observed in the blood test room and emergency departments, rather than in the other five departments. Another intriguing finding was the correlation between ARGs and MGEs abundance. This correlation was evident in the overall hospital indoor environment, which was conversely not found in the emergency, pneumology and gynecology departments. Additionally, while there was no significant relationship that occurred between bacterial communities and ARGs/MGEs within the hospital, the gynecology department demonstrated a close link between bacterial communities and the presence of ARGs/MGEs. Notably, the gynecology department also stood out as an important source of bacteria and ARGs/MGEs for other departments. This study underscores the need for careful surveillance and monitoring of antibiotic resistance, particularly in Legionella spp. in man-made water systems. The findings also show the importance of monitoring and understanding the genetic elements such as Tp614 involved in gene transfer and recombination, as well as their impact on antimicrobial treatment efficacy.

This article reviews recent innovations in piezoelectric actuators, then indicates the future research targets. In the materials, the piezoelectric performances of relaxor-lead titanate (PZN-PT, PMN-PT) single crystals have been improved significantly by an AC electric poling technique. Also new loss characterization techniques facilitate developing high-power density piezoelectrics. The RMS vibration velocity reaches 0.6 m/s in the k₃₁ mode in lead zirconate titanate (PZT) nowadays, which corresponds to power density 30 W/cm³. Pb-free materials are urged due to the recent political regulation on toxic materials. In device designs, the original multilayer actuators (MLA) with Ag/Pd electrode have been switched to the ones with Cu or pure Ag, in order to suppress the heat generation, then to enhance the device power density. Piezoelectric micro-electro-mechanical-systems (MEMS’s) started to utilize the <1 0 0> oriented epitaxial films of rhombohedral PZT compositions, which exhibits enhanced piezoelectric properties. Also for higher-power applications, aero-sol deposition (AD) methods have been introduced to 10 -thick films. Regarding drive/control techniques in piezo-actuators, three developments are on-going, that is, “negative capacitance” power supplies for driving off-resonance (pseudo-DC) piezo-actuators, capacitive AC power supplies for efficiently driving resonance piezo-actuators, and DC/DC converters for harvesting electric energy from high-impedance piezoelectric devices under noise vibration. The applications of piezoelectric actuators in the 21^st century seem to be oriented toward “politico-engineering” with four keywords, “cooperation, protection, reduction, and continuation”. The sustainability technologies include the following piezoelectric items: (a) Pb-free piezoelectrics, (b) ultrasonic technology for decomposing hazardous materials, (c) reduction of contamination gas, (d) piezoelectric energy harvesting, and (e) device improvement with high energy-efficiency. On the other hand, the following crisis technologies have been developed with piezoelectrics: (a) detection and neutralization technologies of infectious/epidemic diseases such as anthrax, (b) autonomous unmanned underwater, aerial, and land vehicles with piezoelectric actuators, (c) pin-point target weapons, (d) high voltage supplies with piezoelectric transformers, and (e) compact energy sources for remote actuating/sensing systems.

Ontological premises have profound theoretical implications. This analysis posits a single, universal structure composed of two ontic entities: discrete, quantized units of space ("Planck Spheres") and a State of Absolute Nothingness (the "SOAN"). Planck Spheres and the SOAN form a physical, ultra-high (3 x N) dimensional space ("Planck Space") and a discrete 3D space (or "4D spacetime"). Together, Planck Space and 4D spacetime form a tightly integrated ((3 x N) + 3) hyperspace (the "Dual Ontology"). Critically, a one-to-one mapping and identity exists between the Planck Spheres comprising 4D spacetime and Planck Space. The Dual Ontology conjecture supports radically simplified physical explanations for three distinct areas of theoretical physics: First, the conjecture reconciles fundamental issues in Special Relativity and quantum mechanics by explaining why single and N-body quantum states (a) dynamically evolve in 4D spacetime subject to the speed of light and (b) instantaneously collapse in a physical Planck Space that is not subject to Special Relativity. Second, the temporal and physical asymmetry between the dynamic evolution of quantum states in 4D spacetime subject to Special Relativity and the instantaneous collapse of quantum states in a Planck Space where Special Relativity is inapplicable explains quantum path irreversibility and the arrow of time. Third, at or near the heat death of 4D spacetime, the instantaneous collapse of the energy content of Planck Space and the simultaneous transition of 4D spacetime's extremely widely dispersed energy content to a non-singular, generally localized volume at t = 0 explains 4D spacetime's isotropy, homogeneity, extremely high energy, pressure, and temperature, flatness, and low gravitational entropy. It also explains the horizon and fine-tuning problems.

Rice blast, caused by Magnaporthe oryzae, poses significant threat to rice production. Rice blast susceptibility has been observed in Japanese rice varieties with excellent eating quality. Enhancing blast resistance is essential to ensure minimal use of agricultural chemicals. Two types of blast resistance are observed: true resistance, which is a type of qualitative resistance expressed by a major gene, and field resistance, which is a type of quantitative resistance expressed by multiple micro-acting genes. ‘Resistance collapse’, in which a variety with a true resistance gene becomes diseased by blast fungus races compatible with the resistance gene, has been observed. Varieties carrying blast-resistance genes, such as Pb1 (panicle blast resistance 1), have been developed through DNA marker-assisted selection. In this review, we focus on the Pb1, which expresses strong quantitative resistance to panicle blast and has been widely used in Japan without showing ‘resistance collapse’ for 40 years. Pb1 is an ‘adult plant resistance gene’ that does not exert strong selection pressure on the blast population during the leaf blast stage, thus preventing the selective multiplication of Pb1-compatible blast strains. This epidemiological mechanism prevents ‘resistance collapse’. Interdisciplinary research and breeding are required to sustainably use genes that induce high field resistance.

This paper aims to present the basic assumptions for creation of social Fröhlich condensate and attract attention of other researchers (both from physics and socio-political science) to the problem of modelling of stability and order preservation in highly energetic society coupled with social energy bath of high temperature. The model of social Fröhlich condensation and its analysis are based on the mathematical formalism of quantum thermodynamics and field theory (applied outside of physics). The presented quantum-like model provides the consistent operational model of such complex socio-political phenomenon as Fröhlich condensation. The model of social Fröhlich condensation is heavily based on theory of open quantum systems. Its consistent elaboration needs additional efforts. Evidence of such phenomenon as social Fröhlich condensation is demonstrated by stability of modern informationally open societies Approaching the state of Fröhlich condensation is the powerful source of social stability. Understanding its informational structure and origin may help to stabilize the modern society. Application of the quantum-like model of Frhlich condensation in social and political sciences is really the novel and original approach to mathematical modeling of social stability in society exposed to powerful information radiation from mass-media and internet based sources.

The verticals of 5G, such as the automotive, smart grid and smart cities sectors, will bring lots of new sensors and IoT devices requiring Internet connectivity. Most of these machine-type terminals will be sparsely distributed, covering a very large geographical area and, from time to time, will have to update their software, firmware and/or other relevant data. Given this situation, one viable solution to implement the “Over-the-Air” update of these IoT terminals can be with the aid of GEO satellite systems. However, due to the ultra-dense radio frequency reuse that contemporary High-Throughput Satellite (HTS) systems implement in the access link to serve the IoT terminals, the use of a time-packed Free Space Optical (FSO) link represents a practical solution to avoid the bottleneck that the satellite gateway experiences in the feeder link. The performance of both Detect-and-Forward and Decode-and-Forward relaying strategies are studied, assuming that the single-carrier M-PAM symbols that are transmitted on the optical feeder link are mapped into M-QAM symbols that modulate the multiple subcarriers of the OFDM-based radio access link. In addition, the benefits of encapsulating the NB-IoT frames into DVB-S2(X) satellite frames is also analyzed in detail. The effects of the impairments introduced in both optical feeder and radio access links are characterized in detail, and the end-to-end error correction capabilities of the Modulation and Coding Schemes (MCS) defined in the contemporary releases of the NB-IoT and DVB-S2(X) standards are studied for different working regimes.

Thermal sterilization is generally avoided for 3-D printed components because of the relatively low deformation temperatures for common thermoplastics used for material extrusion-based additive manufacturing. 3-D printing materials required for high-temperature heat sterilizable components for COVID-19 and other applications demands 3-D printers with heated beds, hot ends that can reach higher temperatures than polytetrafluoroethylene (PTFE) hot ends and heated chambers to avoid part warping and delamination. There are several high temperature printers on the market, but their high costs make them inaccessible for full home-based distributed manufacturing required during pandemic lockdowns. To allow for all these requirements to be met for under $1,000, the Cerberus – an open source three-headed self-replicating rapid prototyper (RepRap) was designed and tested with the following capabilities: i) 200^oC-capable heated bed, ii) 500^oC-capabel hot end, iii) isolated heated chamber with 1kW space heater core and iv) mains voltage chamber and bed heating for rapid start. The Cereberus successfully prints polyetherketoneketone (PEKK) and polyetherimide (PEI, ULTEM) with tensile strengths of 77.5 and 80.5 MPa, respectively. As a case study, open source face masks were 3-D printed in PEKK and shown not to warp upon widely home-accessible oven-based sterilization.

This paper provides a brief overview of how the Haug and Tatum Cosmological Model (HTC) outperforms the Λ-CDM model in numerous categories. In particular, we show why the HTC model is a strong competitor to the Λ-CDM model. For example, HTC appears to resolve the Hubble tension by making use of newly-discovered fundamental relationships between the CMB temperature, the Hubble parameter, and cosmological redshift. Moreover, HTC appears to better explain certain early universe telescopic observations than the Λ-CDM model.

Ground-based high-power lasers enable to, in principle, deorbit any kind of space debris object from the low Earth orbit (LEO) by remotely inducing laser-ablative momentum. However, the assessment of efficiency and operational safety depends on many factors like atmospheric constraints or the risk of debris disintegration during irradiation. We analyze laser momentum for a great variety of target geometries and sizes, and – for the first time in a large-scale simulation – include thermal constraints for laser irradiation configuration. Using a coherently coupled 100 kJ laser system at 1030 nm wavelength, 5 ns pulse duration in an optimized pointing elevation angle range, the pulse frequency should amount to less than 10 Hz to prevent fragment meltdown. For mechanically intact payloads or rocket bodies, repetition rates should be even lower. Small debris fragments sized between 10 and 40 cm can be de-orbited by around 100 to 400 station passes with head-on irradiation while objects exceeding 2 m typically require far more than 1000 irradiations for deorbit. Hence, laser-based debris removal cannot be considered a prime space sustainability measure tackling the top-risk large debris, yet it can provide for remediation of a multitude of small-sized debris using small networks of globally distributed laser sites.

Generalized relativistic pseudopotentials (GRPP) of atomic cores implying the use of different potentials for atomic electronic shells with different principal quantum numbers give rise to accurate and reliable relativistic electronic structure models of atoms, molecules, clusters, and solids. These models readily incorporate the effects of Breit electron-electron interactions and one-loop quantum electrodynamics effects. Here we report the computational procedure for evaluating one-electron integrals of GRPP over contracted Gaussian functions. This procedure was implemented in a library of routines named LIBGRPP, which can be integrated into existing quantum chemistry software, thus enabling the application of various methods to solve the many-electron problem with GRPPs. Pilot applications to electronic transitions in the ThO and UO2 molecules using the new library and intermediate-Hamiltonian Fock space relativistic coupled cluster method are presented. The results clearly demonstrate that rather economical tiny-core GRPP models can exceed in accuracy relativistic all-electron models defined by Dirac-Coulomb and Dirac-Coulomb-Gaunt Hamiltonians.

The combination of interstitial hyperthermia treatment (IHT) with high dose rate brachytherapy (HDR-BT) for prostate cancer treatment and has the potential to improve clinical outcome, since it highly enhances the efficiency of cell kill, especially when applied simultaneously. Therefore, we have developed the ThermoBrachy applicators. To effectively apply optimal targeted IHT, treatment planning is considered essential. However, treatment planning in IHT is rarely applied since it is regarded difficult to accurately calculate the deposited energy in the tissue in a short enough time for clinical practice. In this study, we investigated various time-efficient methods for fast computation of the electromagnetic (EM) energy deposition resulting from the ThermoBrachy applicators. Initially, we investigated the use of an electro-quasistatic solver. Next, we extended our investigation to the application of geometric simplifications. Furthermore, we investigated the validity of the superpositioning principle, which can enable adaptive treatment plan optimization without the need for continuous recomputation of the EM field. Finally, we evaluated the accuracy of the methods by comparing them to the golden standard Finite-Difference Time-Domain calculation method using gamma-index analysis. The simplifications considerably reduced the computation time needed, improving from &gt;12 h to a few seconds. All investigated methods showed excellent agreement with the golden standard by showing a &gt;99% passing rate with 1%/0.5 mm Dose Difference and Distance-to-Agreement criteria. These results allow the proposed electromagnetic simulation method to be used for fast and accurate adaptive treatment planning.

The vulnerability of alpine environments to climate change presses an urgent need to accurately model and understand these ecosystems. Popularity in use of digital elevation models (DEMs) to derive proxy environmental variables has increased over the past decade, particularly as DEMs are relatively cheaply acquired at very high resolutions (VHR; <1m spatial resolution). Here, we implement a multiscale framework and compare DEM-derived variables produced by Light Detection and Ranging (LiDAR) and stereo-photogrammetry (PHOTO) methods, with the aims of assessing their relevance and utility in species distribution modelling (SDM). Using a case study on the arctic-alpine plant Arabis alpina in two valleys in the western Swiss Alps, we show that both LiDAR and PHOTO technologies can be relevant for producing DEM-derived variables for use in SDMs. We demonstrate that PHOTO DEMs rivalled the accuracy of LiDAR, putting the current paradigm of LiDAR being the more accurate of the two methods into question. We obtained DEMs at spatial resolutions of 6.25cm-8m for PHOTO and 50cm-32m for LiDAR, where we determined that the optimal spatial resolutions of DEM-derived variables in SDM were between 1 and 32m, depending on the variable and site characteristics. We found that the reduced extent of PHOTO DEMs altered the calculations of all derived variables, which had particular consequences on their relevance at the site with heterogenous terrain. However, for the homogenous site, we found that SDMs based on PHOTO-derived variables generally had higher predictive powers than those derived from LiDAR at matching resolutions. From our results, we recommend carefully considering the required DEM extent to produce relevant derived variables. We also advocate implementing a multiscale framework to appropriately assess the ecological relevance of derived variables, where we caution against the use of VHR-DEMs finer than 50cm in such studies.

The primary screening of hybridoma cells is a time-critical and laborious step during the development of monoclonal antibodies. Often critical errors occur in this phase, which supports the notion that the generation of monoclonal antibodies with hybridoma technology is difficult to control and hence a risky venture. We think that it is crucial to improve the screening process to eliminate most of the immanent deficits of the conventional approach. With this new microarray-based procedure, several advances could be achieved: Selectivity for excellent binders, high throughput, reproducible signals, avoidance of misleading avidity (multivalency) effects, and simultaneous performance of competition experiments. The latter can directly be used to select clones of desired cross-reactivity properties. In this paper, a model system with two excellent clones against carbamazepine, two weak clones and blank supernatant has been designed to examine the effectiveness of the new system. The excellent clones could be detected largely independent of the IgG concentration, which is unknown during the clone screening since the determination and subsequent adjustment of the antibody concentration is not possible in most cases. Furthermore, in this approach, the enrichment, isolation, and purification of IgG for characterization is not necessary. Raw cell culture supernatant can be used directly, even when fetal calf serum (FCS) or other complex media had been used. In addition, an improved method for the oriented antibody-immobilization on epoxy-silanized slides is presented. Based on the results of this model system, we conclude that this approach should be preferable to most other protocols leading to many of false positives, causing expensive and lengthy confirmation steps to weed out the poor clones.

Additive manufacturing (AM) or 3D printing is a promising industrial technology that enables rapid prototyping of complex configurations. Powder Bed Fusion (PBF) is one of the most popular AM techniques for metallic materials. Until today, only a few metals and alloys are available for AM, e.g. titanium alloys, the most common of which is Ti-6Al-4V. After optimization of the PBF parameters, with or without post processing such as heat treatment or hot isostatic pressing, the printed titanium alloy can easily reach tensile strengths of over 1100 MPa due to the quickly cooling of AM process. However, attributed to the unique features of metallurgical defects and microstructure introduced by this AM process, their fatigue strength has been low, often only not less than 30% of the tensile strength, especially in very-high-cycle regime, i.e. failure life beyond 107 cycles. Here, we have reviewed the current state of research on the very-high-cycle fatigue (VHCF) of additively manufactured (AMed) titanium alloys, refined the basic quantities of AMed microstructure and metallurgical defects, summarized the main factors limiting their VHCF strengths, and suggested possible ways to improve VHCF performance.

Polyetheretherketone is a promising material for implants due to its good mechanical properties and excellent biocompatibility. Its accessibility to a wide range of applications is facilitated by the ability to process it with an easy-to-use manufacturing process such as Fused Filament Fabrication. The elimination of disadvantages associated with the manufacturing process, such as a poor surface quality, is a main challenge to deal with. As part of the mass finishing process, centrifugal disc finishing has demonstrated good results in surface optimization, making it a promising candidate for post-processing of additively manufactured parts. The objective of this study is to identify the key parameters of the centrifugal disc finishing process on the waviness of additively manufactured PEEK specimen, which has not been investigated yet. Waviness of the specimen was investigated by means of confocal laser scanning microscopy (CLSM), while weight loss was additionally tracked. Six parameters were investigated: type, amount and speed of media, use of compound, amount of water and time. Type of media, time and speed were found to significantly influence waviness reduction and weight loss. Surface electron microscopy images demonstrated the additional effects of deburring and corner rounding. Results on previous studies with specimens made of metal showed similar results. Further investigation is required to optimise waviness reduction and polish parts in a second post-processing step.

A general procedure is described, to generate material parameter sets to simulate fire propagation in horizontal cable tray installations. Cone Calorimeter test data is processed in an inverse modelling approach. Here, parameter sets are generated procedurally and serve as input for simulations conducted with the Fire Dynamics Simulator (FDS). The simulation responses are compared with the experimental data and ranked based on their fitness. The best fitness was found for a test condition of \SI{50}{\kilo\watt\per\meter^2}. Low flux conditions \SI{25}{\kilo\watt\per\meter^2} and less exhibited difficulties to be simulated accurately. As a validation step, the best parameter sets are then utilised to simulate fire propagation within a horizontal cable tray installation and are compared with experimental data. It is important to note, the inverse modelling process is focused on the Cone Calorimeter and not aware of the actual validation step. Despite this handicap, the general features in the fire development can be reproduced, however not exact. The fire in the tray simulation extinguishes earlier and the total energy release is slightly higher as compared to the experiment. The responses of the material parameter sets are briefly compared with a selection of state of the art procedures.

The generation of isogenic induced pluripotent stem cell (iPSC) lines using CRISPR-Cas9 technology is a technically challenging, time-consuming process with variable efficiency. Here we use fluorescence-activated cell sorting (FACS) to sort biallelic CRISPR-Cas9 edited single-cell iPS clones into high-throughput 96-well microtiter plates. We used high-content screening (HCS) technology and generated an in-house developed algorithm to select the correctly edited isogenic clones for continued expansion and validation. In our model we have gene-corrected the iPSCs of a Parkinson’s disease (PD) patient carrying the autosomal dominantly inherited heterozygous c.88G>C mutation in the SNCA gene, which leads to the pathogenic p.A30P form of the alpha-synuclein protein. Undertaking a PCR restriction-digest mediated clonal selection strategy prior to sequencing, we were able to post-sort validate each isogenic clone using a quadruple screening strategy. Subsequent transfection with mRNA encoding excision-only transposase allows for the generation of footprint-free isogenic iPSC lines. These monoclonal isogenic iPSC lines retain a normal molecular genotype, express pluripotency markers and have the ability to differentiate into the three germ layers. This combinatory approach of FACS, HCS and post-sorted restriction digestion facilitates the generation of isogenic cell lines for disease modelling to be scaled-up on an automated platform.

Three-dimensional (3D) printing technologies are transforming the design and manufacture of components and products across a variety of disciplines, however their application in the construction industry is still limited. Material deposition processes can achieve infinite geometries and have advanced from rapid prototyping and model-scale markets to their application in fabricating functional products, large objects and the construction of full-scale buildings. Many international projects have recently been realized and the construction industry is beginning to utilise these dynamic technologies. The potential advantages for integrating 3D printing into house construction are significant, these include the capacity for mass customization of designs and parameters for functional and aesthetic purposes, reduction in construction waste from highly precise material placement, and the use of recycled waste products in layer deposition materials. With the ultimate goal of improving construction efficiency and decreasing building costs, applying Strand7 Finite Element Analysis software, a numerical model was designed specifically for 3D printing in a cement mix incorporated with recycled waste product High Density Polyethylene (HDPE) and found that construction of an arched truss-like roof was structurally feasible without the need for steel reinforcements. The lab sizes prototypes were manufactured based on the destined numerical model by using a 3D printing technology. Currently available 3D printing technologies can be adopted for building construction and this paper discusses the applications, advantages, limitations and future directions of 3D printing as an innovative and viable solution for affordable house construction.

During middle age, women are less susceptible to nonalcoholic steatohepatitis (NASH) than men. Thus, we investigated the underlying molecular mechanisms behind these sexual differences using an established rat model of NASH. Mature female and male stroke-prone spontaneously hypertensive 5/Dmcr rats were fed control or high-fat-cholesterol (HFC) diets for 2, 8, and 14 weeks. Although HFC-induced hepatic fibrosis was markedly less severe in females than in males, only minor gender differences were observed in expression levels of cytochrome P450 enzymes (CYP)7A1, CYP8B1 CYP27A1, and CYP7B1, and multidrug resistance-associated protein 3, and bile salt export pump, which are involved in fibrosis-related bile acid (BA) kinetics. However, the BA detoxification-related enzymes UDP-glucuronosyltransferase (UGT) and sulfotransferase (SULT) 2A1, and the nuclear receptors constitutive androstene receptor (CAR) and pregnane X receptor (PXR), were strongly suppressed in HFC fed males, and were only slightly changed in HFC-diet fed females. Expression levels of the farnesoid X receptor and its small heterodimer partner were similarly regulated in a gender-dependent fashion following HFC feeding. Hence, the pronounced female resistance to HFC-induced liver damage likely reflects sustained expression of the nuclear receptors CAR and PXR and the BA detoxification enzymes UGT and SULT.

The classification of Trojans in modern analog microcircuits is considered. Using high-speed operational amplifiers (Op-Amps) as an example, the relationship between Op-Amp circuit design and the formation of undesirable states in typical switching circuits is shown. Circuit solutions are proposed to minimize the Trojan states of high-speed Op-Amps. These include limiting the maximum output currents of the input stages of the Op-Amp during the transient process and the use of differentiating transient correction circuits in the Op-Amp.

Melting phase relations of the diamond-forming system olivine (Ol) – jadeite (Jd) – diopside (Di) – (Mg, Fe, Ca, Na)-carbonates (Carb*) – (C-O-H-fluid) are studied in experiments at 6.0 GPa in the polythermal section Ol74Carb*18.5(C-O-H)7.5 - Omp74Carb*18.5(C-O-H)7.5, where Ol = Fo80Fa20, Omp (omphacite) = Jd62Di38 and Carb* = (MgCO3)25(FeCO3)25(CaCO3)25(Na2CO3)25. Peritectic reaction of olivine and jadeite-bearing melt with formation of garnet has been determined as a physico-chemical mechanism of ultrabasiс-basiс evolution of the diamond-forming system. In the process CO2-component of the supercritical C-O-H-fluid can react with silicate components to form additional carbonates of Mg, Fe, Ca and Na. Solidus temperature of the diamond-forming system is depressed to 1000-1020°C by joint effect of the H2O-fluid and carbonate constituents thereof. The experimentally recognized peritectic mechanism of ultrabasiс-basiс evolution of the diamond-forming system explains the origin of the associated paragenetic inclusions of peridotite and eclogite minerals in diamonds as well as the xenoliths of diamond-bearing peridotites and eclogites of the kimberlitic deposits of diamond. The diamond-forming systems have formed with the use of material of the upper mantle native peridotite rocks. In this case the capacity of the rocks to run the peritectic reaction of olivine was transmitted with silicate components to the diamond-forming systems.

High temperature (HT) geothermal wells can provide green power 24h a day 7 days a week. Harsh environmental and operational conditions, long-term durability requirements of such wells require special cementitious composites for well construction. This paper reports a comprehensive assessment of geothermal cement composites in cyclic pressure function laboratory tests, field exposures in an HT geothermal well (300-350oC) as well as a numerical model to complement the experimental results. Performances of calcium-aluminate-cement (CAC)-based composites and calcium free cement were compared against reference Ordinary Portland Cement (OPC)/silica blend. The stability and degradation of the tested materials was characterized by crystalline composition, thermo-gravimetric, and elemental analyses, morphological studies, water-fillable porosity, and mechanical properties measurements. All CAC-based formulations outperformed the reference blend both in the function and exposure tests. The reference OPC/silica lost its mechanical properties during the 9-month well exposure through extensive HT carbonation, while properties of the CAC-based blends improved over that period. The Modified Cam-Clay (MCC) plasticity parameters of several HT cement formulations were extracted from triaxial and Brazilian tests and verified against the experimental results of function cyclic tests. These parameters can be used in well integrity models to predict field-scale behavior of the cement sheath under geothermal well conditions.

Engineering application of additively manufactured (AM) metallic materials is quite limited by their fatigue behaviors which are very inconsistent with that of conventionally wrought or cast ones. Here, based on advanced material characterization techniques, such as focused ion beam (FIB), scanning electron microscopy (SEM) and transmission electron microscopy (TEM), the mi-crostructures underneath fracture surfaces were thoroughly investigated in an AM aluminium (AlSi10Mg) alloy with horizontal and vertical building orientation endured very-high-cycle fa-tigue (VHCF) loading under stress ratios R = –1, 0 and 0.5. Two VHCF failure specimens A and B were representatively selected to further SEM examine and TEM samples preparation via FIB milling. Specimen A was horizontally printed and failed at R = –1; specimen B was vertically printed and failed at R = 0. TEM samples A1 and B1 were lifted from locations near the crack ini-tiation sites on the fracture surfaces of specimens A and B; The locations of TEM samples A2 and B2 kept away from the crack origin sites but still within the “fish-eye” region of crack steady growth. TEM observations show that there was no characteristic microstructure induced by VHCF in different oriented specimens and under various R values.

This paper attempts to develop a Dynamic Mode Decomposition (DMD) based Reduced Order Model (ROMs) which can quickly but accurately predict the forces and moments experienced by a road vehicle such that they be used by an on-board controller to determine the vehicle's trajectory. DMD can linearize a large dataset of high-dimensional measurements by decomposing them into low-dimensional coherent structures and associated time-dynamics. This ROM then also can be applied to predict the future state of the fluid flow. Existing literature on DMD is limited to low Reynolds number applications. This paper presents DMD analyses of the flow around an idealized road vehicle, called the Ahmed body, at a Reynolds number of 2.7E6. The high dimensional dataset used in this paper was collected from a computational fluid dynamics (CFD) simulation performed using Menter's shear stress transport (SST) turbulence model within the context of Improved Delayed Detached Eddy Simulations (IDDES). The DMD algorithm, as available in literature, was found to suffer nonphysical dampening of the medium-to-high frequency modes. Enhancements to the existing algorithm were explored, and a modified DMD approach is presented in this paper which includes: (a) a requirement of higher sampling rate to obtain higher resolution of data, and (b) a custom filtration process to remove spurious modes. The modified DMD algorithm thus developed was applied to the high Reynolds number, separation dominated flow past the idealized ground vehicle. The effectiveness of the modified algorithm was tested by comparing future predictions of force and moment coefficients as predicted by the DMD-based ROM to the reference CFD simulation data, and found to offer significant improvement.

A novel stationary phase for affinity separations is presented. This material is based on sintered borosilicate glass readily available as semi-finished filter plates with defined porosity and surface area. The material shows fast binding kinetics and excellent long-term stability under real application conditions due to lacking macropores and high mechanical rigidity. The glass surface can be easily modified with standard organosilane chemistry to immobilize selective binders or other molecules used for biointeraction. In this paper, the manufacturing of the columns and their respective column holders by 3D printing is shown in detail. The model system protein A/IgG was chosen as an example to examine the properties of such monolithic columns under realistic application conditions. Several specifications, such as (dynamic) IgG capacity, pressure stability, long-term performance, productivity, non-specific binding, and peak shape, are presented. It could be shown that due to the very high separation speed, 250 mg antibody per hour and column can be collected, which surpasses the productivity of most standard columns of the same size. The total IgG capacity of the shown columns is around 4 mg (5.5 mg/mL), which is sufficient for most tasks in research laboratories. The cycle time of an IgG separation can be less than 1 minute. Due to the glass material's excellent pressure resistance, these columns are compatible with standard HPLC systems. This is usually not the case with standard affinity columns, limited to manual use or application in low-pressure systems. The use of a standard HPLC system also improves the ability for automation, which enables the purification of hundreds of cell supernatants in one day. The sharp peak shape of the elution leads to an enrichment effect, which might increase the concentration of IgG by a factor of 3. The final concentration of IgG can be around 7.5 mg/mL without the need for an additional nanofiltration step. The purity of the IgG was > 95% in one step and nearly 99% with a second polishing run.

Posttraumatic stress disorder (PTSD) and/or specific PTSD symptoms may evoke disordered eating and unhealthy lifestyles, resulting in adverse cardiometabolic events (e.g., hypertension and obesity) in certain groups, which may implicate the treatment of this complex condition. The diagnostic criteria of PTSD have lately expanded beyond the three common symptoms (intrusion, avoidance, and hyperarousal). Simultaneously, four-, five-, and six-dimensional structures of the Impact of Event Scale-Revised (IES-R), a popular PTSD measure, seem to be more robust than the original three-dimension structure. Within the context of COVID-19, this instrumental study used a convenience sample of 58 dental healthcare workers (HCWs) from Russia (mean age = 44.1±12.2 years, 82.8% females) to examine the criterion and predictive validity of two IES-R structures: the IES-R3 and the IES-R6 (with the added symptoms of numbing, sleep disturbance, and irritability). The subscales of the two IES-R structures expressed good internal consistency, strong correlations with the PTSD Symptom Scale (PSS), hypertension diagnosis, and high body mass index (BMI). In receiver-operating characteristic (ROC) curve analysis, all IES-R models perfectly predicted the PSS (all area under the curve (AUC) >0.9, p values <0.001). The IES-R, both hyperarousal subscales, and the IES-R3 intrusion subscale significantly predicted high BMI. Both avoidance subscales and the IES-R3 intrusion subscale, not the IES-R, significantly predicted hypertension. In conclusion, both IES-R structures can reliably measure PTSD symptoms. The IES-R, hyperarousal, and intrusion may be credible criterion variables for predicting high BMI within PTSD while the intrusion and avoidance subscales may reflect the cardiovascular consequences associated with PTSD more reliably than the IES-R itself. The IES-R subscales may predict cardiometabolic adversities in PTSD, signifying a need for proper assessment of lifestyle and the application of dietary and exercise interventions in order to lower physical morbidity in PTSD. Replicating the study in larger samples, which comprise different physical and mental conditions from heterogenous cultural contexts is pivotal to validate the results (e.g., in specific groups such as those with confirmed traumatic exposure and comorbid mood dysfunction).

Neuroblastoma (NB) is a solid tumor occurring in infancy and childhood, whose high-risk form has currently a survival rate &lt; 50 %, despite aggressive treatments. Additionally, drugs-induced secondary tumorigenesis and the emergency of drug resistance worsen the already worrying scenario, calling for an urgent development of new extra-genomic treatments. Quaternary phosphonium salts (QPSs) possess both antimicrobial and anticancer effects. Triphenyl phosphonium salts (TPPs) are mitochondria-targeting compounds, exerting anticancer effects, impairing mitochondria functions and damaging DNA, at the same time. TPP-based bola-amphiphiles, previously proven to self-assemble nanoparticles (NPs) in water and successfully assayed as possible antibacterials, were never tested as suitable antitumor agents. Here, aiming at the development of new antitumor devices to counteract resistant forms of NB, the anticancer effects of a TPP-based amphiphile molecule have been investigated for the first time. To this end, we considered the water-soluble sterically hindered quaternary phosphonium salt (BPPB) encompassing two triphenyl phosphonium groups linked by a C12 alkyl chain, thus embodying both the characteristics of mitochondria-targeting compounds and those of bola-amphiphiles. The anticancer effects of BPPB were assessed against HTLA-230 human stage-IV NB cells and their counterpart resistant to etoposide (ETO), doxorubicin (DOX) and to many other therapeutics (HTLA-ER). Determined IC50 values were very low on both cell populations, already after 24 hours of treatment, when cells viability did not significantly differ from that observed for the longest exposure timing. Moreover, to investigate a putative future inclusion of BPPB in a chemotherapeutic cocktail for NB, its cytotoxic effects were assessed against mammalian cell lines. These included monkey kidney cells (Cos-7), human hepatic cells (HepG2), a lung-derived fibroblast cell line (MRC-5) and red blood cells. From appreciable to very high selectivity indices have been determined after 24 hours treatments, an exposure time after which both NB cell populations tested appeared already fully exterminated.

We report a case of colloid carcinoma (CC) arising from an intestinal-type intraductal papillary mucinous neoplasm with high-grade dysplasia (IPMNHGD) of the pancreas, diagnosed with serial pancreatic juice aspiration cytological examination (SPACE). A rapidly growing intraductal papillary mucinous neoplasm (IPMN) in a 71-year-old Japanese man accelerated his hospitalization in our institute. Clinically, a large, ruptured pancreatic cyst was suspected. Cytologically, several mucin-positive signet-ring cells were scattered in the inflammatory, necrotic, or mucinous background. Signet-ring cells in cell block specimens were immunoreactive for MUC2, MUC5AC, maspin, S100P, and claudin-18. The final cytologic diagnosis was CC arising in an intestinal-type IPMNHGD with intraperitoneal penetration. The patient died two months postoperatively. The cytologic diagnosis was achieved through SPACE, and the presence of signet-ring cells was characteristic. Anti-claudin-18.2-specific monoclonal antibody therapy will likely be used to treat patients with IPMNHGD in the future. To our knowledge, this is the first report in English on mucin-positive signet-ring cells of CC arising in an intestinal-type IPMNHGD evaluated by SPACE cytology.

The morphology of virgin reactor powder (RP) of high-density polyethylene HDPE with MW = 160,000 g/mol was investigated with the help of DSC, SEM, SAXS and WAXS methods. The morphological SEM analysis showed, that the main morphological units of RP are macro- and micro-shish kebab structures with significantly different geometric dimensions, as well as individual lamellae of folded chain crystals. Quantitative analysis of an asymmetric SAXS reflection made it possible to reveal the presence of several periodic morphoses in the RP with long periods from 20 nm to 60 nm and to correlate them with the observed powder morphology. According to the DSC crystallinity data, the thickness of the lamellae in each long period was estimated. Their surface energy was calculated in the framework of the Gibbs-Thompson theory. The presence of regular and irregular folds on the surface of the different shish-kebab lamellae is discussed. The percentage of identified morphoses in the RP was calculated. It has been suggested that the specific structure of HDPE RP is due to the peculiarity of polymer crystallization during suspension synthesis in a quasi-stationary regime, in which local overheating and inhomogeneous distribution of shear stresses in a chemical reactor are possible.

The vast majority of patients with pancreatic ductal adenocarcinoma (PDAC) suffer cachexia. Although cachexia results from concurrent loss of adipose and muscle tissue, most studies focus on muscle alone. Emerging data demonstrate the prognostic value of fat loss in cachexia. Here we sought to identify the muscle and adipose gene profiles and pathways regulated in cachexia. Matched rectus abdominis muscle and subcutaneous adipose tissue were obtained at surgery from patients with benign conditions (n=11) and patients with PDAC (n=24). Self-reported weight loss and body composition measurements defined cachexia status. Gene profiling was done using Ion proton sequencing. Results were queried against external datasets for validation. 961 DE genes were identified from muscle and 2000 from adipose tissue, demonstrating greater response of adipose than muscle. In addition to known cachexia genes such as FOXO1, novel genes from muscle, including PPP1R8 and AEN correlated with cancer weight loss. All the adipose correlated genes including SCGN and EDR17 are novel for PDAC cachexia. Pathway analysis demonstrated shared pathways but largely non-overlapping genes in both tissues. Age related muscle loss predominantly had a distinct gene profiles compared to cachexia. This analysis of matched, externally validate gene expression points to novel targets in cachexia.

Several studies have shown that physical activity (PA) is related to physical and mental health. Yet, there are few studies on the frequency of PA as it relates to health and a healthy lifestyle. The purpose of this study was to investigate the relationship between the frequency of practicing different types of physical activities (dependent variables), living a healthy lifestyle (BMI, smoking and alcohol consumption), physical health (sum of all doctor visits except psychiatrists) and mental health (a sum of visits to psychiatrists) at different ages (independent variables). We fo-cused on three types of PA: (1) medium to high-intensity aerobic exercises; (2) low to medium intensity relaxing and stretching exercises, (3) outdoor leisure PA. 9,617 participants (ages: 19 -81) were included in the study (with health registries over a period of 10 years prior to a cross-sectional survey). Descriptive statistics and multinomial logistic regression on frequencies of three types of PA and factors related to health and healthy lifestyles, as well as age and sex, were performed in this study. The results indicate that a higher frequency of practicing PA had a higher probability of association with the following factors: lower BMI, less or non-smoking behavior (types 1 & 3); higher education (types 1 & 2); higher age (types 2 & 3) and better physical health (type 1). Occasional (practicing sometimes) PA, type 2, was positively associated with poorer mental health (higher number of psychiatrist visits). Women were more likely to practice PA type 2, and men – PA types 3 & 1. Conclusion: In general, a higher frequency of PA is related with better health and healthy life styles; with the exception of PA type 2 that is related to poorer mental health.

The goods and services produced by forest vegetation ecosystem are the driving force for the rapid, high-quality and sustainable development of human society. In history, with the increase of population and economic development, there is an increasing demand for the quantity and variety of forest vegetation ecosystem products and services in a country or a region. To meet the demands, most of the original forest has become farmland, plantation and grass and crops land. As a result, the plant water relationship changed from equilibrium to non-equilibrium, which easily led to soil drought, soil degradation and vegetation decline in dry years or waste of soil water in rainy years in most of water-limited regions. In order to solve the question and realize the sustainable utilization of soil water resources and the high-quality sustainable development of forest, it is necessary to apply the limit theory of plant utilization of soil water resources and the vegetation carrying capacity theory in the critical period of plant-water relationship regulation to adjust the relationship between plant growth and soil moisture to obtain the maximum yield and benefit and realize high-quality and sustainable development.

Background: Co-treatment of the fetal estrogen estetrol (E4) with androgen deprivation therapy (ADT) for advanced prostate cancer (PCa) may further inhibit endocrine PCa tumor stimulators including testosterone (T), prostate-specific antigen (PSA), follicle-stimulating hormone (FSH), and insulin-like growth factor-1 (IGF-1). Methods: A Phase II, double-blind, randomized, placebo-controlled study in advanced PCa patients requiring ADT (the PCombi study) was conducted to assess the effect of E4 co-treatment with LHRH agonist ADT on total T, free T, PSA, FSH, and IGF-1. Patients starting ADT were randomized 2:1 to 40 mg E4 (n=41) or placebo (n=21) for 24 weeks. Analyses were performed on the per-protocol population (PP), using the Wilcoxon-rank sum and the Kruskal-Wallis test. Results: The PP population consisted of 57 patients (37 ADT+E4; 20 ADT+placebo). All individual data of the four endocrine tumor stimulators are presented in figures in the paper and in supplementary tables, showing that E4 co-treatment almost completely suppressed FSH levels in all patients, on average by 98% versus 37% in the placebo group (p

While paresthesia-based spinal cord stimulation (SCS) has been proven effective to treat chronic neuropathic pain, initial benefits may lead to the development of “Failed SCS Syndrome’ (FSCSS) defined as decrease over time related to Loss of Efficacy (LoE) with or without Loss of Coverage (LoC). Development of technologies associating new paresthesia-free stimulation waveforms and implanted pulse generator adapters provide opportunities to manage patients with LoE. The main goal of our study was to investigate salvage procedures, through neu-rostimulation adapters, in patients already implanted with SCS and experienced LoE. We retro-spectively analyzed a cohort of patients who were offered new SCS programs/waveforms through an implanted adapter between 2018 and 2021. Patients were evaluated before, and at 1, 3, 6 and 12-month follow-up. Outcomes included pain intensity rating with Visual Analog Scale (VAS), pain/coverage mappings and stimulation preferences. Last follow-up evaluations (N=27) showed significant improvement in VAS (p = 0.0001), ODI (p = 0.021) and Quality of Life (p=0.023). In the 11/27 patients with LoC, SCS efficacy on pain intensity (36.89%) was accompa-nied by paresthesia coverage recovery (55.57%) and pain surface decrease (47.01%). At 12-month follow-up, 81.3% preferred to keep tonic stimulation in their waveform portfolio. SCS conver-sion using adapters appears promising as a salvage solution, with an emphasis on paresthesia recapturing enabled by spatial retargeting. In light of these results, adapters could be integrated to SCS rescue algorithms or should be considered in SCS rescue.

Using multi-color flow cytometry analysis, we studied the immunophenotypical differences between leukemic blasts/LSCs from patients with AML/MDS and hematopoietic stem and progenitor cells (HSPCs) from patients in complete remission (CR) following their successful treatment. The panel of markers included CD34, CD38, CD45RA, CD123 as representatives for a hierarchical hematopoietic stem and progenitor cell (HSPC) classification as well as programmed death ligand 1 (PD-L1). Rather than restricting the evaluation on a 2- or 3-dimensional analysis, we applied a t-distributed stochastic neighbor embedding (t-SNE) approach to get a deeper insight and segregation between leukemic and normal HPSCs. For that purpose, we created a t-SNE map, which resulted in the visualization of 27 cell clusters based on their similarity concerning the composition and intensity of antigen expression. Two of these clusters were “leukemia-related” containing a great proportion of CD34⁺/CD38^- hematopoietic stem cells (HSCs) or CD34⁺ cells with a strong coexpression of CD45RA/CD123, respectively. CD34⁺ cells within the latter cluster were also highly positive for PD-L1 reflecting their immunosuppressive capacity. Beyond this proof of principle study, the inclusion of additional markers will be helpful to refine the differentiation between normal HSPCs and leukemic cells, particularly in the context of minimal disease detection and antigen-targeted therapeutic interventions. Furthermore, we suggest a protocol for the assignment of new cell ensembles in quantitative terms, via a numerical value, the Pearson coefficient, based on a similarity comparison of the t-SNE pattern with a reference.

Multi-junction solar cells comprised of stacked III-V semiconductor junctions represent the highest-efficiency photovoltaic technology, with recent demonstrations exceeding 47% efficiency . Optimizing the design and thickness of each junction is critical for maximizing performance . This work utilizes Silvaco TCAD tools to systematically optimize a 5-junction cell based on AlInP, AlGaInP, AlGaInAs, GaInP, GaAs, InGaAs, and Ge similar to recent record cells . The junction thicknesses are varied using a predictive profiler to sample the parameter space . For each combination, the spectral absorption and I-V characteristics are simulated to determine the efficiency . Statistical analysis identifies the optimal thickness set that maximizes performance to 26% under 1 sun illumination .

During the conceptual and preliminary design stage of a ship, designers need to ensure that the selected principal dimensions and parameters are good enough to deliver a stable ship (statically and dynamically) besides deadweight and speed. To support this, the initial intact stability of the proposed ship is required to be calculated, and in doing so, the lightship weight and its detailed breakdown are necessary to be known. After hull steel weight, machinery weight, mainly, marine propulsion and power generation machinery, play a vital role in the lightship weight estimate of a ship due to its robustness. The correct estimation of respective weights improves the accuracy of calculating a ship's initial stability typically to be designed and built. Hence, it would be advantageous for the designer to convince the ship owner. A total of 3006 marine propulsion (main marine diesel) engines and 348 power generation (auxiliary marine diesel) engines/generators of various power output (generators output for auxiliary engines), engine RPM and cylinder number of different engine makers are collected. These are analyzed and presented in both tabular and graphical forms to demonstrate the possible relationship between marine propulsion engine weight and power generation engine weight, and their respective power output, RPM, cylinder number, power-RPM ratio and power-RPM ratio per cylinder.In this article, the authors have attempted to investigate the behavior of marine propulsion engine weight and power generation engine/generator weight regarding engine power output, generator power output, engine RPM and cylinder number (independent variables). Further attempts have been made to identify those independent variables that influence the weight of the marine propulsion engine and power generation engine/generator (dependent variables), and their interrelationships. A mathematical model has thus been developed and proposed, as a guiding tool, for the designer to estimate the weight of main and auxiliary engines more accurately during the conceptual and preliminary design stage.