This study aimed to establish and verify the validity of an acoustic simulation method during sustained phonation of the Japanese vowels /i/ and /u/. The study participants were six healthy adults. First, vocal tract models were constructed based on computed tomography (CT) data, such as the range from the frontal sinus to the glottis, during sustained phonation of /i/ and /u/. Next, cylindrical shapes virtually extended by 12 cm were added to the vocal tract models to imitate the trachea between the tracheal bifurcation and lower part of the glottis. The Kirchhoff–Helmholtz integral equation was formulated as the wave equation for sound propagation, and the boundary element method was used for discretization. As a result, the relative discrimination thresholds of the vowel formant frequencies for /i/ and /u/ against actual voice were 1.1%–10.2% and 0.4%–9.3% for the first formant and 3.9%–7.5% and 5.0%–12.5% for second formant, respectively. In the vocal tract model with nasal coupling, a pole–zero pair was observed at around 500 Hz, and for both /i/ and /u/, a pole–zero pair was observed at around 1000 Hz regardless of the presence or absence of nasal coupling. These findings demonstrated that /i/ and /u/ could be simulated with high validity in a vocal tract model constructed from CT data obtained during sustained phonation using the boundary element method.

In the construction of shield crossing existing mined tunnel without load, it is imperative to develop corresponding design standards that reflect actual engineering force characteristics to ensure the successful completion of tunnel construction. This research uses The MIDAS-GTS finite element software to facilitate the creation of a numerical model of the shield structure for an air-push-over mine tunnel project in Changsha, China, investigating the stress field’s evolution during shield construction, and calculating the maximum positive and negative bending moments and maximum axial forces for different structures and other force states under various construction conditions. This study's findings informed the design and construction optimisation of the shield tunnelling empty-push method. The outcomes of this numerical simulation led to several key findings: (1) The soil density exerted a significantly greater impact on the internal forces of the initial support structure than both the tunnel depth and soil Poisson's ratio. Additionally, a sudden shift in internal forces occurred within the 300-350 mm range when the lining thickness was altered. (2) Factors such as the tunnel depth, soil density, soil Poisson's ratio μ, and lining thickness have a similarly influenced internal forces of the segment and the initial support. Notably, the backfill layer thickness significantly affected the segment’s maximum axial force causing an abrupt change of approximately 300 mm. (3) Under the shield machine equipment’s weight constraint, it is essential to control the guide rail’s thickness, to prevent it from becoming overly large.

Keywords: Deep mining; Drill bit structural parameters; Fidelity coring; Abaqus simulation and analysis.

Precipitation downscaling is widely employed for enhancing the resolution and accuracy of precipitation products from general circulation models (GCMs). In this study, we propose a novel statistical downscaling method to foster GCMs’ precipitation prediction resolution and accuracy for monsoon region. We develop a deep neural network composed of convolution and Long Short Term Memory (LSTM) recurrent module to estimate precipitation based on well-resolved atmospheric dynamical fields. The proposed model is compared against GCM precipitation product and classical downscaling methods in the Xiangjiang River Basin in South China. Results show considerable improvement compared to the ECMWF-Interim reanalysis precipitation. Also, the model outperforms benchmark downscaling approaches, including 1) quantile mapping, 2) support vector machine, and 3) convolutional neural network. To test the robustness of the model and its applicability in practical forecast, we apply the trained network for precipitation prediction forced by retrospective forecasts from ECMWF model. Compared to ECMWF precipitation forecast, our model makes better use of the resolved dynamical field for more accurate precipitation prediction at lead time from 1 day up to 2 weeks. This superiority decreases along forecast lead time, as GCM’s skill in predicting atmospheric dynamics being diminished by the chaotic effect. At last, we build a distributed hydrological model and force it with different sources of precipitation inputs. Hydrological simulation forced with the neural network precipitation estimation shows significant advantage over simulation forced with the original ERA-Interim precipitation (with NSE value increases from 0.06 to 0.64), and the performance is just slightly worse than the observed precipitation forced simulation (NSE=0.82). This further proves the value of the proposed downscaling method, and suggests its potential for hydrological forecasts.

This paper presents an advanced and highly sophisticated model for hybrid electric special-purpose machines (HE-SPMs), specifically engineered to significantly enhance sustainability and efficiency in logistics operations. The primary objective of this model is centered around the optimization of energy flow, a feature that has undergone extensive testing and validation to ensure its reliability and effectiveness. The inclusion of auxiliary systems such as cutting-edge cooling and control systems further elevates the overall performance capabilities of the HE-SPMs, resulting in a seamless integration within various industries. By implementing these enhanced systems, substantial reductions in energy consumption and operational costs have been observed and well-documented through compelling case studies in both the construction and transportation sectors. The holistic nature of this approach impeccably aligns with the ongoing global efforts aimed at combating the pressing issue of climate change. By focusing on the development and utilization of eco-friendly technologies, this model actively contributes to the mitigation of harmful environmental impacts and promotes sustainable practices within the logistics industry. To further reinforce the efficacy of this remarkable model, future research endeavors will concentrate on expanding its applications to encompass other logistics domains.

Nuclear export of viral mRNAs, is an essential step in the HIV replication cycle. This role is played by a small regulatory protein of HIV-1 called Rev.The N-terminal region of Rev contains an arginine-rich sequence. The arginine-rich motif (ARM) is located between amino acids 38-50 and forms an alpha-helical secondary structure. Expression of the structural proteins of human immunodeficiency virus type 1 requires the direct interaction of multiple copies of the viral Rev protein with its highly structured RNA target sequence, the Rev Response element (RRE). The major viral proteins are not produced if this transport of RNA is stopped. Therefore, knowledge of Rev structure is essential for understanding of its cooperative binding to the RRE, for understanding the mechanism of HIV infection and for the development of antiviral drugs that interfere with Rev’s essential functions and for acknowledgment of good candidate drugs for treatment of AIDS. To understand how REV interact with RRE element of HIV-RNA and its formation of oligomeric complex it is better to characterize the domain wise structure of REV with regard in function of each domain. Due to lack of structural data on Rev no single compound is reported as inhibitor of REV expect antiviral drugs. Identification of a high-affinity RNA-binding site for the human immunodeficiency virus type 1 Rev Protein is much more important. The ARM is a highly specific sequence which allows for the multimerization of Rev and also binding of REV with RNA. Here we are first time exploring the structural characteristics of REV protein both in free form and in complex with RNA at domain function level especially explore the role of ARM motif in REV HIV-1 protein as RNA binding sites by molecular dynamics (MD) simulation and homology modeling studies. Results indicate that the arginine-rich motif (ARM) is crucial in stability of this complex. The residues ARG38, 39, 41, 43, 44, 48, 50, and ASN40 are most interacting with nucleobases of RRE in Crystal structure of Rev and Rev-response-element RNA complex. Our study plays a major role in elaboration of binding of RNA with REV and pave the way for further investigation for therapeutically agent for HIV.

In this study, three new demountable joints consisting of reinforced concrete columns and steel beams were proposed and their seismic performance was investigated using cyclic loading tests. The test results demonstrated that the three demountable RCS joints had good seismic performance. Using the finite element software ABAQUS, the influence of parameters such as beam flange thickness, bolt strength, and connector steel strength on the seismic performance of each joint was analyzed, and the influence of different parameters on the seismic behavior of the joint was determined. The results also showed that the three demountable RCS joints were sensitive to changes in the thickness of the steel beam flange, while the connector steel strength and bolt type had little impact on the joint's capacity. Additionally, shear capacity calculation formulas for the joint core area provided by different codes and researchers were compared with test and finite element results. The results showed that the calculation results of the ASCE guidance method, the Nishiyama method, and the CECS 347-2013 method were higher than the test values, while the calculation results of the Para method were lower because it did not consider the contribution of the cylindrical steel plate to the shear capacity of the joint core area.

This research investigated the antihypertensive effects of tamarind products and compared their potentials based on their animal model’s data verified by molecular docking, multitarget interactions in network pharmacology, and dynamic simulation assays. The GC-MS characterized tamarind products were administered to the cholesterol-induced hypertensive Wistar albino rat models. Two-week-intervened animals were dissected to collect serum and organs which were respectively subjected to the analyses of hypertension-linked markers and tissue architectures. Lead biometabolites of tamarinds interacted with eight target receptors in molecular docking and dynamic simulation studies and they were tested for multitarget interactions using network pharmacological analyses. Results showed that serum alanine aminotransferase (ALT), aspartate aminotransferase (AST), alkaline phosphatase (ALP), C-reactive protein (CRP), Troponin I, and lipid profiles were maximally reinstated by the phenolic-enriched ripened sour over the sweet tamarind flesh extracts, but seed extracts had a smaller influence. Among the tamarind’s biometabolites, Gamma-sitosterol (ϒ-sitosterol) was found to be the best ligand in managing hypertension via the possible ligand-receptor interactions with the guanylate cyclase which displayed the best drug-likeliness through the highest binding energy -9.3 Kcal. Multitargeted interactions-based degree algorithm and phylogenetic tree of pathways showed 14 targeted genes, of which NR3C1, REN, PPARG, and CYP11B1 hub genes, were consistently modulated by the ϒ-sitosterol to reduce hypertension and related risk factors. The dynamic simulation study showed that the P-RMSD values of ϒ-sitosterol-guanylate cyclase were stable between 75.00 to 100.00 ns at the binding pocket. The findings demonstrate that ripened sour tamarind extract may be supplemented to be a more prospective antihypertensive target or nutraceuticals affirming through advanced preclinical and clinical studies.

In this paper we investigate in different scenarios the feasibility of using massive multiple-input multiple-output (mMIMO) with Reconfigurable Intelligent Surfaces (RISs) to boost the throughput and coverage performances with high energy efficiency, considering sub-6 GHz, mmWave and THz bands. With that objective, a centralized radio access network (C-RAN) suitable for beyond fifth generation (B5G) systems is considered, where we integrate the base stations (BSs) with multiple RISs and devices or user equipment. RISs with a large number of quasi-passive reflecting elements constitute a low-cost approach capable of shaping the radio wave propagation and improve wireless connectivity. We consider a scenario where multiple RISs are combined with mMIMO in the uplink in order to provide connectivity to Smart City (thousands of active low power devices) wirelessly, in the 3.6GHz and 28GHz bands. We also address a scenario where RISs are adopted with mMIMO in the downlink so as to offer connectivity to a Stadium with Pitch, (thousands of active user equipment) in the 28GHz band. Finally, we have also studied the connectivity at 100GHz of a Factory where several RIS panels replacing most of the BSs equipped with mMIMO assure improved throughput and coverage. We concluded that RISs are capable of improving the performance in any of these analyzed scenarios at the different frequency bands, justifying that they are a key enabling technology for 6G.

Abstract: The purpose of this study is to explore, from the perspective of government interven-tion, behavioral logic and game relationship among farmers, service organizations and the gov-ernment in the pest and disease control outsourcing system, as well as the endogenous motiva-tion of each subject. The results indicate that the stronger the willingness of each subject, the faster the stable state of joint pest and disease control among the three parties can be formed; In the case of implementing a single policy tool, the convergence rate of each party that imple-ments the regulatory policy alone is fast but may be unstable, while the rate is slow but more stable when a guidance- or incentive-based policy is solely applied; The effect of policy tool combination is much better than that of a single policy tool applied. The simultaneous imple-mentation of the three types of policy tools can form a policy system with both positive and negative mechanisms, which can maximize complementary and superposition effect.

Ocean surface waves have been utilized as fundamental information in various fields of oceanic research. In this paper, we suggest a simulation and modelling technique for generating an ocean surface wave using an inverse Fast Fourier Transform (iFFT), and we subsequently verify the wave’s accuracy. The conventional method, linear superposition, requires recursive calculation because of the double summation and the time variable; to circumvent this issue, the new algorithm is presented. The Joint North Sea Wave Project (JONSWAP) spectrum is utilized for the ocean surface wave simulation example, and the parameters are the significant wave height (HS) and the zero-crossing wave period (TZ). A coordinate transform for the wavenumber domain was used to apply the inverse FFT algorithm. To verify the accuracy of the simulation result, the relative error between the input condition and the analysis result was calculated. The result for TZ is below 4% relative error, and the maximum relative error for HS is 7%. To avoid the Nyquist frequency for wave-field analysis and simulation, the minimum grid size was calculated by twice applying the maximum wavenumber.

In this note, I analyze the data generated by M. Fodje's (2013) simulation programs "epr-simple" and "epr-clocked". They were written in Python and published on Github. Inspection of the program descriptions shows that they make use of the detection-loophole and the coincidence-loophole respectively. I evaluate them with appropriate modified Bell-CHSH type inequalities: the Larsson detection-loophole adjusted CHSH, and the Larsson-Gill coincidence-loophole adjusted CHSH (NB: its correctness is conjecture, we do not have proof). The experimental efficiencies turn out to be approximately eta = 81% (close to optimal) and gamma = 55% (far from optimal). The observed values of CHSH are, as they should be, within the appropriately adjusted bounds. Fodjes' detection-loophole model turns out to be very, very close to Pearle's famous 1970 model, so the efficiency is close to optimal. The model has the same defect as Pearle's: the joint detection rates exhibit signaling. Fodje's coincidence-loophole model is actually a clever modification of his detection-loophole model. Because of this, however, it cannot lead to optimal efficiency.

Certain configurations of liquefied natural gas refueling stations exhibit a deficiency in managing boil-off gas. Furthermore, the ill-conceived linkage between the submersible pump and the gas storage tank pipeline leads to impeded natural gas transmission. This study employs Computational Fluid Dynamics (CFD) methodology to scrutinize the hydrodynamic attributes of T-type tee and dovetail tee configurations implemented in the pipeline design connecting the submersible pump and storage tank in an LNG filling station across diverse operational scenarios. The T-type tee induces detachment of the primary flow from the inner wall due to inertial forces, resulting in vortex formation and heightened resistance, accompanied by increased energy dissipation. Conversely, the dovetail tee, with its circular wall transition, mitigates vortex generation, reducing the separation zone and consequently minimizing resistance and energy loss. The maximum static differential pressure between the inlet and outlet of the dovetail tee is diminished by 52.52% when compared to that of the T-type tee. In the most noteworthy scenarios, the local resistance coefficient of the dovetail tee is even less than 1/10 of that of the T-type tee. In practical engineering applications, the incorporation of dovetail tees leads to a 17.58% reduction in the required elevation difference. This results in a more uniform flow field and enhanced stability in both flow rate and pressure. Such improvements contribute to heightened engineering efficiency and environmental sustainability, particularly evident in the design of LNG filling stations.

With the development of engineering technology, engineering has higher requirements for the accuracy and the scale of simulation calculation. The computational efficiency of traditional se-rial program can not meet the requirements of engineering。Therefore, reducing the calcula-tion time of temperature control simulation program has important engineering significance for real-time simulation of temperature field and stress field, and then adopting more reasona-ble temperature control and crack prevention measures. GPU parallel computing is introduced into the temperature control simulation program of massive concrete to solve this problem and the optimization is carried out. Considering factors such as GPU clock rate, number of cores, parallel overhead and Parallel Region, The improved GPU parallel algorithm analysis indicator formula is proposed. It makes up for the shortcomings of traditional formula that focus only on time. According to this formula, when there are enough threads, the parallel effect is limited by the size of the parallel domain, and when the parallel domain is large enough, the efficiency is limited by the parallel overhead and the clock rate. This paper studies the optimal Kernel execu-tion configuration. Shared Memory is utilized to improve memory access efficiency by 155%. After solving the problem of bank conflicts, an accelerate rate of 437.5x was realized in the sub-routine of the matrix transpose of the solver. The asynchronous parallel of data access and logi-cal operation is realized on GPU by using CUDA Stream , which can overlap part of the data access time. On the basis of GPU parallelism, asynchronous parallelism can double the compu-ting efficiency. Compared with the serial program, the accelerate rate of inner product matrix multiplication of the GPU asynchronous parallel program is 61.42x. This study further proposed a theoretical formula of data access overlap rate to guide the selection of the number of CUDA streams to achieve the optimal computing conditions. The GPU parallel program compiled and optimized by CUDA Fortran platform can effectively improve the computational efficiency of the simulation program for concrete temperature control, and better serve for engineering computing.

The powder bed fusion (PBF) metal additive manufacturing (AM) method uses an energy source like a laser to melt the metal powders. The laser can locally melt the metal powders and creates a solid structure as it moves. The complexity of the heat distribution in laser PBF metal AM is one of the main features that need to be accurately addressed and understood to design and manage an optimized printing process. In this research, the dependency of local thermal rates and gradients on print after solidification (in the heat-affected zone) was numerically simulated and studied to provide information for designing the print process. The simulation results were validated by independent experimental results. The simulation shows that the local thermal rates are higher at higher laser power and scan speed. Also, the local thermal gradients increase if the laser power increases. The effect of scan speed on the thermal gradients is opposite during heating versus cooling times. Increasing the scan speed increases the local thermal gradients in the cooling times and decreases the local thermal gradients during the heating. In addition, these simulation results could be used in artificial intelligence (AI) and machine learning for developing digital additive manufacturing.

The use of unmanned aerial vehicle (UAV) during emergency response of a disaster has been widespread in recent years and the terrain images captured by the cameras on board these vehicles are significant sources of information for such disaster monitoring operations. Thus, analyzing such images are important for assessing the terrain of interest during such emergency response operations. Further, these UAVs are mainly used in disaster monitoring systems for the automated deployment of sensor nodes in real time. Therefore, deploying and localizing the wireless sensor nodes optimally, only in the regions of interest that are identified by segmenting the images captured by UAVs, hold paramount significance thereby effecting their performance. In this paper, the highly effective nature-inspired Plant Growth Simulation Algorithm (PGSA) has been applied for the segmentation of such terrestrial images and also for the localization of the deployed sensor nodes. The problem is formulated as a multi-dimensional optimization problem and PGSA has been used to solve it. Furthermore, the proposed method has been compared to other existing evolutionary methods and simulation results show that PGSA gives better performance with respect to both speed and accuracy unlike other techniques in literature.

The effect of the angular rolling process on the plan view pattern of the plate is studied, the rectangular influence factor and improvement method for plate angular rolling process are proposed in this paper. Finite element models are established for the conventional rolling and angular rolling processes respectively, and with DEFORM software, the numerical simulation is carried out. A characterization formula reflecting the rectangular degree of the rolled piece is constructed and the rectangular degree of the plates under different rolling process conditions are compared. Considering the actual rolling process conditions, the range of theoretically calculated rectangular rotation angles is extended to obtain the optimum rectangular rotation angle with finite element simulation method. The one-group two-pass angular rolling is separated to one-group four-pass rolling and the simulation results show that the rectangular degree of the four-pass process is better than the two-pass process. Angular rolling experiments are carried out, the actual data shows that the rectangular characteristic value of the rolled piece is 1.003 with the four-pass process, and 1.014 with the two-pass process. It verifies that with separating one-group two-pass angular rolling process to one-group four-pass angular rolling process can improve the rectangular degree of the rolled plate.

Time-of-Flight (ToF) cameras are subject to high levels of noise and errors due to Multi-Path-Interference (MPI). To correct these errors, algorithms and neuronal networks require training data. However, the limited availability of real data has led to the use of physically simulated data, which often involves simplifications and computational constraints. The simulation of such sensors is an essential building block for hardware design and application development. Therefore, the simulation data must capture the major sensor characteristics. This work presents a learning-based approach that leverages high-quality laser scan data to generate realistic ToF camera data. The proposed method employs MCW-Net (Multi-Level Connection and Wide Regional Non-Local Block Network) for domain transfer, transforming laser scan data into the ToF camera domain. Different training variations are explored using a real-world dataset. Additionally, a noise model is introduced to compensate for the lack of noise in the initial step. The effectiveness of the method is evaluated on reference scenes to quantitatively compare to physically simulated data.

This work proposes a conceptual design for a process for recovering Polystyrene (PS) using solvents of agro-industrial origin. The literature describes the dilution of Expanded Polyestyrene (EPS) in limonene, followed by its insolubilization with alcohols for recovery. However, there is no information on the solubility limit for the PS + limonene + alcohol system, which is critical for the process design. To determine the solubility limit, we diluted the waste EPS in D-limonene, mixed it with ethanol to form a precipitate, and used a gravimetric method to measure the mass of the compounds. These results allowed for the conceptual design of an EPS recycling process using a chemical process simulator, which includes a separator, a distillation column, and auxiliary equipment such as heaters, coolers, and pumps. An empirical correlation was obtained for the solubility limit, which enabled the design of a process for the treatment of 52 kg/s of PS using 0.75 kg /s of ethanol and 2.4 kg / s of D-limonene once the stationary state had been reached. The distillation column is six-stage, with a reflux ratio of 1.5 and duties of 30 000 kW and -25 847 kW for the condenser and reboiler, respectively.

In this study, we develop a stochastic partial differential equation (SPDE) model to assess the regional severity of temperature increases due to global warming. The model incorporates various stochastic processes to account for uncertainties such as solar explosions, economic upheavals, rising emissions, and irreversible changes in the climate system. Our base temperature model, influenced by latitude, is enhanced by these random factors to simulate realistic and diverse outcomes of climate change. Numerical simulations on a global grid provide a heatmap representing potential temperature increase severity across different regions. The results highlight the significant impact on tropical and polar regions, demonstrating the utility of SPDE models in understanding and predicting the complex dynamics of climate change. This approach offers valuable insights for policymakers and researchers aiming to develop adaptive strategies for mitigating the adverse effects of global warming.

The use of energy resources is essential to the survival and development of human civilization. However, inefficient energy use not only has an impact on the economy, but it also has a significant impact on climate change. Studying and analyzing the factors that increase energy consumption is crucial for improving energy management. The aim of this study is to analyze the factors influencing energy savings in a building taken as a study model under two different climatic conditions. Measurements of the building's energy performance were carried out using the EnergyPlus calculation engine, which enabled us to analyze the strengths of building parameters such as the number of lights, the equipment used, occupancy, temperature and the relationships between the factors influenced. EnergyPlus is an important software tool in the field of building energy efficiency, enabling the precise simulation of building energy consumption. Simulation scenarios based on actual consumption data carried out by researchers have made it possible to develop energy management strategies in buildings in order to optimize energy efficiency, and in particular to promote the thermal performance of these buildings. In the present work, EnergyPlus building energy simulation software is used to simulate the energy consumption of the building of the Faculty of Electrical Engineering at the "Gheorghe Asachi" Technical University in Iasi, in order to determine the factors influencing building energy consumption. It has been shown that occupancy and heating and cooling systems are the key factors influencing energy consumption in buildings. The advantage of this study is that it can be used to model the most influential factors in predicting future energy consumption in buildings.

Community centers play a crucial role in urban environments, providing physical and educational services to their surrounding communities, particularly for students. Among the many benefits for students are enhanced academic outcomes, improvement of behavioral problems, and increased school attendance. Such centers are also particularly vital for low-income and racial minority students as they are pivotal in giving them outside-of-school learning opportunities. However, determinants influencing attendance at community centers remain largely unexplored. Using census data, Boston Centers for Youth and Families (BCYF) attendance data, and specific center attributes, we develop human mobility gravitational models to predict attendance across the BCYF network. Using those models, we investigate the potential effects on general and student attendance by changing center attributes, such as facilities and operating hours. We also research the impact of changing the walking accessibility to those centers on their respective attendance patterns. After the analysis, we find that the most cost-effective policy to increase BCYF attendance is changing each center’s educational and recreational offerings far beyond any accessibility interventions. Our results provide insights into potential policy changes that could optimize the attendance and reach of BCYF Community Centers to underserved populations.

Motivated by the increasing need of optimised micro-devices for droplets production in medical and biological applications, this paper introduces an integrated approach for the study of the liquid-liquid droplet creation in flow-focusing micro cross-junctions. The micro-junction considered is characterised by a restriction of the channels cross-sections in the junction, which has the function of focusing the flow in the region of the droplet formation. The problem is studied numerically in OpenFOAM environment and validated by the comparison with experimental results obtained by high-speed camera images and micro-PIV measurements. The analysis of the forces acting on the dispersed phase during the droplet formation and the diameter of the droplets obtained numerically are considered for the development of a model of the droplet breakup under the squeezing regime. On the basis of energy balancing during the breakup, a relation between interfacial tension, the size of the cross-sections in the junction, and the time interval needed for droplet creation is obtained, which yields a novel correlation between the dimensionless length of the droplet and the dimensionless flow rate. This correlation is general and can be used to predict the droplet diameters produced by similar micro-junctions with different aspect ratios and extended to different geometries of flow-focusing micro-junctions.

Hydrogen storage in high pressure tanks can occur with different filling strategies. Many studies have been carried out on supplies with increasing pressure rates. However, hydrogen filling with constant mass inflow rate have not received the same attention. The present work aims to carry out numerical simulations to study hydrogen flow, in a type 3 tank of 70 MPa NWP and constant inflow rate condition. From the analysis of the results, it was possible to verify that there is a linear relationship between the increase in the total equilibrium temperature and the final hydrogen temperature. There is also a linear increasing relationship between Inlet and final temperatures when the equilibrium temperature is fixed. Considering fully adiabatic walls results in significant increases in temperature. The difference between total and static temperatures found in the Inlet tube decreases with the decrease in mass flow rate. The choice of a polymer for the tank lining led to higher temperatures when compared to an aluminum lining.

Swirling coal flames are encountered in swirl burners of boiler furnaces and cyclone coal combustors, and were studied using large-eddy simulation (LES) in reported references. However, the structures of swirling coal flames remain to be further studied. In the present paper LES of swirling coal flames is conducted for two combustors using two gas combustion models. The statistical simulation results are accessed by experiments and the instantaneous simulation results are used to analyze the specific features of flame structures of four cases. It is seen that different inlet flow conditions and different secondary-air flow rate lead to different flame structures

An atomic-scale approach is employed to simulate the formation of precipitates with different lattice misfits in the early stages of aging of supersaturated aluminum alloys. Simulation results reveal that the increase of lattice misfit could significantly promote the nucleation rate of precipitates, which results in a larger number and smaller size of the precipitates. The morphologies of the precipitates also vary with the degree of lattice misfit. Moreover, the higher the lattice misfit, the earlier the nucleation of the second phase occurs, which can substantially inhibit the movement of dislocations. The research on the lattice misfit of precipitation can provide theoretical guidance for the design of high-strength aluminum alloy.

Cellular automata (CA) models have emerged as a valuable tool in corrosion management. This manuscript provides an overview of the application of cellular automata models in corrosion research, highlighting their benefits and contributions to understanding the complex nature of corrosion processes. Cellular automata models offer a computational approach to simulate corrosion behavior at the microscale, capturing the intricate interactions between electrochemical reactions, material properties, and environmental factors generating a new vision of predictive maintenance. It discusses the key features of cellular automata, such as the grid-based representation of the material surface, the definition of state variables, and the rules governing cell-state transitions. The ability to model local interactions and emergent global behavior makes cellular automata particularly suitable for simulating corrosion processes. Finally, cellular automata models offer a powerful and versatile approach to studying corrosion processes, expanding models that can continue to enhance our understanding of corrosion and contribute to the development of effective corrosion prevention and control strategies.

The information society has transformed human life. Technology is almost everywhere, including health and education. For example, years ago, speech and language therapy students required a long time and high-cost equipment to develop healthcare of the auditory and vestibular systems competencies. The high cost of the equipment permitted its practical use only in classes, hindering students’ autonomy in developing those competencies. That situation was a real issue, even more in times of pandemic where online education was essential. This article describes SAEF, an open-source software simulator for autonomously developing procedural audiology therapy competencies, user acceptance, and the validity of experiments and results. SAEF delivers immediate feedback and performance results. Obtained results permit validating students’ and educators’ acceptability of SAEF in audiology therapy education. Obtained results invite authors to continue developing simulator software solutions in other health education contexts. SAEF was developed using open-source technology to facilitate its accessibility, classification, and sustainability.

A large amount of steel slag (SS) and CO2 are generated in the steelmaking process. The indirect CO2 capture using SS is a promising way for co-treatment of the wastes. Ammonium salt solution is widely used to extract Ca2+ from the SS since it is recyclable. Several works have focus on improving the carbonation rate by adjusting various parameters (e.g., temperature and pH). However, there is little detail information about the associating behaviors and interaction strength between the various ions in the ammonia solution during the carbonation process. In this work, the Ca2+–CO32-–NH4+–Cl-–H2O system was established by using Material studio software. The effects of temperature and concentration of CO32- on CaCO3 growth were explored at the atomic scale by calculating the binding energy, mean square displacement, and diffusion coefficient between particles. Furthermore, the microstructure, bonding characteristics, and occurrence behavior of each particle were studied though molecular dynamics simulation methods. The results showed that with the increase of temperature (20–80 ℃), the binding ability and diffusion coefficients of Ca2+ and CO32- increase in the system, which is beneficial to the formation of CaCO3 clusters. With the increase of the concentration of CO32- (15–25 vol.%), the binding ability and diffusion coefficient of Ca2+ and CO32- in the system are enhanced, which is beneficial to the formation of CaCO3 clusters.

Simulation-Based Medical Education that uses Virtual Patients has become increasingly important during the COVID-19 pandemic. With the need for social distancing and minimizing contact, medical simulation technology has provided a valuable tool for healthcare professionals to practice and improve their skills without the need for face-to-face interactions. MedSIM is a medically accurate simulation platform with Virtual Patients designed for undergraduate medical education. Our study involved two groups of students. The PreCOVID group, before the pandemic, underwent conventional teaching methods. The COVID group, during the pandemic, had students exposed to conventions skills taught earlier and were taught again with MedSIM. Students indicated high satisfaction with the clinical skills demonstrated by the Virtual Patients. More than half agreed that MedSIM had enabled them to perform all kinds of procedures on patients (PreCOVID group 68.8%, COVID group 71.3%), showed cues and consequences much like those in natural clinical environments (PreCOVID 68.4%, COVID 71.3%). Also, MedSIM allowed them to have a repetitive practice that helps in critical skills transfer to actual patients (PreCOVID 72.7%, COVID 74.7%). MedSIM met the expectations of most of the students. Students from both groups rated the online performance of the MedSIM simulator as "Very good." Analysis from a customized word cloud indicated that most students found MedSIM to be good and of educational value. MedSIM platform enhances healthcare professionals' skills and knowledge, leading to better patient outcomes and increased access to healthcare, supporting SDG 3 (Good Health and Well-being). It also provides a safe and controlled environment for healthcare professionals to learn and practice essential skills, supporting SDG 4 (Quality Education).

A novel physiologically based algorithm (PBA) for fast CFD computation of Flow Fractional Reserve (FFR) in Coronary Artery Trees (CATs) is proposed and developed, which, unlike traditional methods, is based on the extension of the Murray’s law for blood vessels at the outlets and extra inlet conditions prescribed alternatively and iteratively. The PBA is then implemented in both SimVascular and Ansys CFD for testing and validation. For validation purpose, 3D models of CATs are built by using their CT images and computational meshes generated for mesh convergence study. Results obtained are then compared with Invasive Coronary Angiographic (ICA) data for validation and evaluation of its accuracy and computational efficiency. It is found that discrepancies between experimental and calculated values of pressure and flow rate at the inlet were less than 0.1% at the end of the 10^th round of iteration or less. Further validation shows that the difference between estimated and experimental FFR agree with each other with a maximum difference of 1.62% after convergence is achieved. The PBA is found to be a robust patient-specific and physiologically sound method that can be a good alternative to the existing Lumped Parameter Model (LPM) which is based on empirical scaling correlations using limited population-averaged data and requires nonlinear iterative computation for convergence.

Porcelain tile manufacturing is an energy-intensive industry that is in dire need of increasing productivity, minimizing costs, and reducing CO2 emissions, while keeping the product quality intact to remain competitive in today’s environment. In this contribution, alternative processing parameters for the porcelain tile production sequence were proposed based on simulation-based process optimization. Flowsheet simulations in the Dyssol framework were used to study the impact of milling and firing process parameters on the electrical and thermal energy consumption, final product quality, and productivity of the entire processing sequence. For this, a new model of gas flow consumption in the sintering stage was proposed and implemented. During optimization, the primary condition was to maintain the product quality by keeping the final open porosity of the tile within the specified industrial range. The proposed simulation methodology proved to be effective in predicting the influence of processing parameters on the intermediate and final products of the manufacturing sequence, as well as in estimating production costs for the Brazilian and Spanish economic conditions. This approach has shown great potential to promote digitalization and establish digital twins in ceramic tile manufacturing for further in-line process control.

Loop detectors are probably the widest-used technology for traffic state estimation. Previous research has shown that loop detector positions within the link significantly affect the estimation of the macroscopic fundamental diagram (MFD) of a given network. This paper examines the biases produced by the positioning of loop detectors on the MFD, using both analytical and simulation methods, as well as empirical data from UTD-19. We confirm earlier results that a uniform distribution of loop detector positions reduces the bias. For non-uniform distribution, we found that: (i) the subsets of the MFD by the loop detector position help estimate whether the loop detector MFD will have a bias; (ii) if the detectors in the network are positioned more downstream with a larger variation, the loop detector MFD is more likely to have a discrepancy in position subsets of the MFD; (iii) a lower ratio of link length to green signal time elevates the MFD bias as well. This research opens the possibility for the bias of MFD induced by the loop detector data to be corrected by only using itself.

Locomotor impairment is a high-prevalent and significant source of disability and significantly impacts a large population’s quality of life. Despite decades of research in human locomotion, the challenges of simulating human movement to study the features of musculoskeletal drivers and clinical conditions remain. Most recent efforts in utilizing reinforcement learning (RL) techniques are promising to simulate human locomotion and reveal musculoskeletal drives. However, these simulations often failed to mimic natural human locomotion because most reinforcement strategies have yet to consider any reference data regarding human movement. To address these challenges, in this study, we designed a reward function based on the trajectory optimization rewards (TOR), and bio-inspired rewards, which includes the rewards obtained from reference motion data captured by a single Intertial Moment Unit (IMU) sensor. The sensor was equipped on the participants’ pelvis to capture reference motion data. Also, we adapted the reward function by leveraging previous research in walking simulation for TOR. The experimental results showed that the simulated agents with the modified reward function performed better in mimicking the collected IMU data from participants, which means the simulated human locomotion was more realistic. Also, as this bio-inspired defined cost, IMU data enhanced the agent’s capacity to converge during the training process. As a result, the models’ convergence is faster than those developed without reference motion data. Consequently, human locomotion can be simulated more quicker and in a broader range of environments with a better simulation performance.

ASEAN SME has a role as the regional socioeconomic stabilizer. This particular role is inseparable from endogenous multi-sector collaboration. Although, Indonesian SMEs were struggled in adopting Industry 4.0 correspond to digital infrastructure and digital literacy problems. This study evaluates Indonesian SME collaboration dynamics with government and technology startup (TS). The integration of agent-based model and causal loop simulation were employed to assess the TS collaboration impact on SME Industry 4.0 adoption and SME competition with larger competitors. The simulation results imply the SME collaboration with TS can lead to early adoption of Industry 4.0 which balances the business competition environment. The model also shows rising the government aid exponentially can help the SME to late adoption of Industry 4.0 which unable to sustain the SME in business competition. Thus, the developed integrative simulation model is a state-action planning model with each state result bounded to the previous state result that determined by initial input parameters. Conclusively, the model can be used as a resiliency planner for SME Industry 4.0 adoption.

A single fracture is the basic unit of fracture medium, and the roughness of fracture wall surface is an important factor influencing hydraulic characteristics of the flow in bedrock fracture. However, effects of the shape and density of roughness elements (various bulges/pits on rough fracture wall surfaces) on water flow in a single rough fracture have not been thoroughly discovered. Thus the water flow in single fracture with different shapes and densities of roughness elements was simulated by using Fluent software in this study. The results show that in wider fractures the flow rate mainly depends on fracture aperture, while in narrow and close fracture medium the surface roughness of fracture wall is the main factor of head loss of seepage; there is a negative power exponential relation between the hydraulic gradient index and the average fracture aperture, i.e. with the increase of fracture aperture, the relative roughness of fracture and the influence weight of hydraulic gradient both decrease; and in symmetrical-uncoupled fractures there is a super-cubic relation between the discharge per unit width and average aperture. Above results would help to deepen the understanding of rough fracture seepage.

In this paper, a method of direct spinning is proposed for direct spinning of heterogeneous spun wire-blown holes standard parts and the motherboard mounted on the spin board assemblies. The standardization of the spinneret hole was conducive to improving the machining accuracy and efficiency of the pores, and the spinneret holes could be replaced in time when a hole in the spinneret fails. Moreover; on the other hand, according to the needs of the process of spinning, the spinnerets with various cross-sections were combined and installed on the same motherboard for spinning, and the spinning obtained different bionic new functional products. Based on the results, a finite element model of the standard part of the spinneret hole was developed, and the spinnability of the combinable spinnable spinneret board was verified by simulating the melt flow in the spinneret channel through POLYFLOW software. Further, by the processing of the spinneret, the motherboard was installed into a combined spinneret, and the spinneret assembly was installed on the spinning machine for the experiments. Furthermore, the tow section was observed using a microscope, and the results showed the feasibility of the proposed method.

Fibre reinforced concrete (FRC) has become an alternative for structural applications due its outstanding mechanical properties. The appearance of new types of fibres and the fibre cocktails that can be configured mixing them has created FRC that clearly exceed the minimum mechanical properties required in the standards. Consequently, in order to take full advantage of the contribution of the fibres in construction projects, it is of great interest to have constitutive models that simulate the behaviour of the materials. This study aimed to simulate the fracture behaviour of five types of FRC, three with steel hooked fibres, one with a combination of two types of steel fibres and one with a combination of polyolefin fibres and two types of steel fibres, by means of an inverse analysis based on the cohesive crack approach. The results of the numerical simulations defined the softening functions of each FRC formulation and have pointed out the synergies that are created through use of fibre cocktails. The information obtained might suppose a remarkable advance for designers using high-performance FRC in structural elements.

In this paper, we use three different experimental methods (particle method, grid method and hybrid method) to model and simulate the smoke from the perspective of fluid dynamics. Through the comparison of different methods, we conclude: The particle method can avoid the numerical dissipation problem caused by grid calculation, but it also brings problems such as the distortion of the trajectory of the example. The grid method is accurate in calculation, but it is prone to numerical dissipation and loss of details. Finally, we choose the hybrid method to store the vorticity in the form of particles in vortex particles, avoiding the numerical dissipation problem caused by the use of grids, and including rich turbulence, which perfectly shows the simulation effect of smoke.

Quantum computers are invaluable tools to explore the properties of complex quantum systems. We show that dynamical localization of the quantum sawtooth map, a highly sensitive quantum coherent phenomenon, can be simulated on actual, small-scale quantum processors. Our results demonstrate that quantum computing of dynamical localization may become a convenient tool for evaluating advances in quantum hardware performances.

The designs of two large arenas of different epochs are discussed, which are the most famous antique amphitheater the Roman Colosseum (Italy) and the modern Gazprom Arena stadium (St. Petersburg, Russia). 3D-computer models of the arenas have been built and evacuation of people has been simulated in the Sigma FS software (Russia). The arena designs are analyzed in terms of organizing pedestrian evacuation, a comparative analysis is made, and the specific characteristics affecting the evacuation time are established.

This code provides computational facilities to simulate current versus time during the charging of Li-ion cells at desire constant voltage by considering multiscale physical phenomena. This code only considers a powder of active materials (at microscale or nanoscale) and a small part of electrolyte around it as a half cell. Then it is extended to a complete cell by applying correct boundary conditions. This code is very useful by modifying code parameters to understand the effect of the complex shape of active materials powder (surface area and powder size), kind of electrolyte, and the applied voltages on the charging response of Li-ion cell. As a summary, a microscale approach to the design of Li-ion cells has been provided via this code.

Background and motivation: Combining Deep Reinforcement Learning (Deep RL) and Health Systems Simulations has significant potential, for both research into improving Deep RL performance and safety, and in operational practice. While individual toolkits exist for Deep RL and Health Systems Simulations, no framework to integrate the two has been established. Aim: Provide a framework for integrating Deep RL Networks with Health System Simulations, and to ensure this framework is compatible with Deep RL agents that have been developed and tested using OpenAI Gym. Methods: We developed our framework based on the OpenAI Gym framework, and demonstrate its use on a simple hospital bed capacity model. We built the Deep RL agents using PyTorch, and the Hospital Simulation using SimPy. Results: We demonstrate example models using a Double Deep Q Network or a Duelling Double Deep Q Network as the Deep RL agent. Conclusion: SimPy may be used to create Health System Simulations that are compatible with agents developed and tested on OpenAI Gym environments. GitHub repository of code: https://github.com/MichaelAllen1966/learninghospital

This paper proposes a novel deterministic methodology for estimating the optimal sampling frequency (SF) of water quality monitoring systems. The proposed methodology is based on employing two-dimensional contaminant transport simulation models to determine the minimum SF considering all the potential changes in the boundary conditions of a water body. A two-dimensional contaminant transport simulation model (RMA4) was implemented to estimate the distribution patterns of the total dissolved solids (TDS) within the Al-Hammar Marsh in the southern part of Iraq for 30 cases of potential boundary conditions. Using geographical information system (GIS) tools, a spatiotemporal analysis approach was applied to the results of the RMA4 model to determine the minimum SF of the monitoring stations with an accuracy level of detectable change in TDS concentration (ALC) of 5%, 10% and 15%. The proposed methodology specified a minimum and maximum SF for each monitoring station (MS) that ranged between 12 and 33 times per year, respectively. Additionally, increasing the ALC to 10% and 15% increase the minimum SF for some MSs by approximately 18% and 21%, respectively. However, the proposed methodology includes all the potential values and cases of boundary conditions, which increases the certainty of monitoring the system and the efficiency of the SF schedule. Moreover, the proposed methodology can be effectively applied to all types of surface water resources.

The increasing variability in power plant load, in response to a wildly uncertain electricity market and the need to to mitigate CO₂ emissions, lead power plant operators to explore advanced options for efficiency optimization. Model-based, system-scale dynamic simulation and optimization are useful tools in this effort, and the subject of the work presented here. In prior work, a dynamic model validated against steady-state data from a 605 MW subcritical power plant was presented. This power plant model is used as a test-bed for dynamic simulations, in which the coal load is regulated to satisfy a varying power demand. Plant-level control regulates plant load to match an anticipated trajectory of the power demand. The efficiency of the power plant operating at varying load is optimized through a supervisory control architecture that performs set point optimization on the regulatory controllers. Dynamic optimization problems are formulated to search for optimal time-varying input trajectories that satisfy operability and safety constraints during the transition between plant states. An improvement in time-averaged efficiency of up to 1.8% points is shown feasible with corresponding savings in coal consumption of 184.8 tons/day and carbon footprint decrease of 0.035 kg/kWh.

The study aims to analyze the performance criteria of the GR4J model to reproduce high water flows in the Ouémé watershed at Bonou's outlet which has been vulnerable to climate change in recent decades. The methodology focused on the use of daily climatological and hydrometric data extracted from files of National Directorate of Meteorology, and General Directorate of Water; they were supplemented by those of SIEREM/HSM dataset over the period 1961-2015. The rainfall was regionalized using Thiessen method. The performance of the GR4J model was assessed with NSE, RMSE and KGE criteria. The results indicate that the study area is marked by rainfall variabilities and detection of two breakpoints (1968 and 1987) which divide the series into three sub-periods; these discontinuities have repercussions on the streamflow. It's found that GR4J model overestimates the streamflow during the low water period and underestimates them in high water. However, the efficiency and performance criteria NSE, RMSE and KGE calculated on high water flow rates are better in calibration than in validation. The KGE values are range between 83-85% in calibration and 56-68% during validation, which gives to GR4J model the efficiency and performance to reproduce high flow rates in the study area

Subsurface temperature is the key parameter in geothermal exploration. An accurate estimation of the reservoir temperature is of high importance and usually done either by interpolation of borehole temperature measurement data or numerical modeling. However, temperature measurements at depths which are of interest for deep geothermal applications (usually deeper than 2 km) are generally sparse. A pure interpolation of such sparse data always involves large uncertainties and usually neglects knowledge of the 3D reservoir geometry or the rock and reservoir properties governing the heat transport. Classical numerical modeling approaches at regional scale usually only include conductive heat transport and do not reflect thermal anomalies along faults created by convective transport. These thermal anomalies however are usually the target of geothermal exploitation. Kriging with trend does allow including secondary data to improve the interpolation of the primary one. Using this approach temperature measurements of depths larger than 1,000 m of the federal state of Hessen/Germany have been interpolated in 3D. A 3D numerical conductive temperature model was used as secondary information. This way the interpolation result reflects thermal anomalies detected by direct temperature measurements as well as the geological structure. This results in a considerable quality increase of the subsurface temperature estimation.

The paper presents the design and the implementation of different advanced control strategies that are applied to a nonlinear model of a thermal unit. A data–driven grey–box identification approach provided the physically meaningful nonlinear continuous–time model, which represents the benchmark exploited in this work. The control problem of this thermal unit is important since it constitutes the key element of passive air conditioning systems. The advanced control schemes analysed in this paper are used to regulate the outflow air temperature of the thermal unit by exploiting the inflow air speed, whilst the inflow air temperature is considered as an external disturbance. The reliability and robustness issues of the suggested control methodologies are verified with a Monte–Carlo analysis for simulating modelling uncertainty, disturbance and measurement errors. The achieved results serve to demonstrate the effectiveness and the viable application the suggested control solutions to air conditioning systems. The benchmark model represents one of the key issues of this study, which is exploited for benchmarking different model–based and data–driven advanced control methodologies through extensive simulations. Moreover, this work highlights the main features of the proposed control schemes, while providing practitioners and heating, ventilating and air conditioning engineers with tools to design robust control strategies for air conditioning systems.

Laser shock peening is a process which can reduce stress corrosion cracking and improve fatigue life by forming compressive residual stress on the surface of the material. In a computational FE simulation of laser shock peening, during applying the pressure load generated by the laser pulse to the surface of simulation geometry, the peening is simulated by explicit analysis and then convert to implicit analysis to dissipate the dynamic energy remaining in the geometry. In this study, static damping is applied to dissipate residual dynamic energy without converting it into an implicit analysis. The compressive residual stress distribution is compared between the simulation results for the stainless steel 304 material and the same material subjected to actual laser shock peening. The laser shock peening parameters were 4.2J laser pulse energy, 50% overlap of 3mm diameter of the laser beam and water as a confinement layer. As a result, the compressive residual stress from the surface to the depth direction is similar to both the simulation and the experimental result measured by the hole drilling method.

With data for SARS-CoV-2 and with many countries entering the second wave of contagion required the improvement of the forecasting model, structuring its model to forecast the peak of the first and second contagion wave in Brazil. The Model Estimation for SARS-CoV-2 Peak Contagion (MESPC) was structured, capable of estimating the peak of contagion for SARS-CoV-2 in the first and second waves, as the main objective of this work. Using the MESPC model, it was possible to estimate, with a certain reliability degree, the peak of contagion for the first and second waves in Brazil, with one day difference from the real to the forecast. It is possible to use MESPC to forecast the peak of contagion for several regions, provided that the necessary structure and calibration are respected.

One of the rapidly developing research areas in the power system is the integration of distributed generation (DG) with the distribution system. The size and location of DG sources had a considerable impact on power system networks. Artificial intelligence (AI) techniques can be used to address multidimensional problems relating to DG size and location in distribution systems. Heuristic optimization offers a reliable and effective method for solving complicated real-world problems. This work focuses on a hybrid approach that combines the two heuristic optimization methods i.e., Particle Swarm Optimization (PSO) and Genetic Algorithm (GA) for the optimal siting and sizing of DG in distribution systems. This hybrid approach combines ideas from GA and PSO and generates individuals in a new generation using both PSO mechanisms and the procedures found in GA. An extensive performance analysis of the IEEE 14 busbar standard test system is conducted to demonstrate the viability of the suggested methodologies. In the designated locations, DG is placed, and the outcomes have been verified. The results indicated that the right placement of DG injection enhances the voltage profile and lowers the distributed system’s power losses. These techniques offer unique methods for determining the location of the DG unit, demonstrating the potential of such a computational techniques to reduce computing time and complexity while simultaneously reducing human errors associated with hit-and-trail methods.

The mechanical behavior, microstructures as well as the crystallographic textures of the Ti57-Nb43 alloy were investigated on cylindrical specimens compressed at high temperatures, in the range of 700-1000 °C, and strain rates between 0.001 and 1.0 s-1. Hardening, followed by softening behaviours were observed as a function of strain, due to the occurrence of dynamic recrystallization/recovery in hot deformation. The modified five-parameter Voce type equation described well the stress-strain curves, but for the present alloy, it was also possible with only four parameters. A new two-variables polynomial function was employed on the four parameters that described well the flow curves as a direct function of temperature and strain rate. It permitted to reduce the number of parameters and had the predictive capacity for the flow stress at any temperature, strain, and strain rate in the investigated range. The crystallographic textures were similar at all temperatures with an increase of intensity from 900 °C. The textures could be characterized by a double <100> and <111> fiber and a unique component of (001)<110>, the latter inherited from the initial hot rolling texture. Viscoplastic polycrystal self-consistent deformation modeling reproduced the measured textures showing that dynamic recrystallization did not alter the development of the deformation texture, only increased it intensity.

Among other fossil fuels, natural gas is a major energy source. It is generally created saturated with water vapor. Dehydration of natural gas is vital in the gas business to remove water vapor from the gas supply, which may cause hydrate development in pipes. Gas dehydration employs Tri ethylene glycol (TEG) to remove water vapor from natural gas flow. The wet gas is dehydrated with lean glycol in an absorber, and the rich glycol is recovered and reused. This work investigates the use of dry natural gas instead of nitrogen in the glycol dehydration re-generator, and compares the results using HYSYS modeling and simulation. The two techniques were compared for capital and utility expenses, while maintaining the identical glycol purity criteria. The wet gas from the stripping mechanisms may also be utilized to run steam pumps and compressors or recycled. The model is based on the real mechanism flow diagram. Finally, the findings of this model might be used to design a new heat and material balance for the plant.

(1) Background: The imaging energy range of a typical Compton camera is limited due to the fact that scattered gamma photons are seldom fully absorbed when the incident energies are above 3 MeV. Further improving the upper energy limit of gamma-ray imaging has important application significance in active interrogation of special nuclear materials and chemical warfare agents, as well as range verification of proton therapy; (2) Methods: To realize gamma-ray imag-ing in a wide energy range of 0.3~7 MeV, a principle prototype, named a portable three-layer Compton camera, was developed using the scintillation detector that consist of an silicon photo-multiplier array coupled with a Gd3Al2Ga3O12:Ce pixelated scintillator array. Implemented in a list-mode maximum likelihood expectation maximization algorithm, a far-field energy-domain imaging method based on two-interaction and three-interaction events was applied to estimate the initial energy and spatial distribution of gamma-ray sources. The simulation model of detec-tors was established based on Monte Carlo simulation toolkit Geant4. The reconstructed images of a 133Ba, a 137Cs and a 60Co point-like sources were successfully obtained with our prototype in laboratory tests and compared with simulation studies; (3) Results: The proportion of effective imaging events accounted for about 2%, which made our prototype realize reconstructing the distribution of a 0.05 μSv/h 137Cs source in 10 seconds. The angular resolution for resolving two 137Cs point-like sources was 15°. Additional simulated imaging of the 6.13 MeV gamma-rays from 14.1 MeV neutron scattering with water preliminarily demonstrated the imaging capability for high incident energy; (4) Conclusions: We concluded that the prototype had good imaging per-formance in a wide energy range (0.3~7 MeV), which showed potential in several MeV gam-ma-ray imaging applications.

The positional deviation of the Automatic Emergency Call System (AECS) under collision conditions brings difficulties for post-rescue operations. Currently, there is a lack of analysis on the system operating conditions during collisions in the reliability assessment methods for the Global Navigation Satellite System (GNSS) deployed in AECS. Therefore, this paper establishes an in-vehicle collision environment simulation model for emergency calls to explore the influence of parameters such as temperature and vibration on the data deviation of the simulated GNSS system. We also propose environmental limits applicable to comprehensive AECS tests, which can objec-tively evaluate the reliability of AECS and provide data support for AECS bench test. Through the satellite signal-based semi-physical simulation, AECS is subjected to bench test under different operating conditions. The findings of this study demonstrate that the occurrence of random vibra-tion and impact stress, induced by vibration, exerts considerable disruptive effects on positional signal data during collisions. Consequently, it leads to substantial interference with the accurate detection of post-collision satellite positioning information. When the simulation operates under a 2.4gRMS vibration condition, the maximum phase noise error in the positioning system is 8.95%, which does not meet the AECS test accuracy requirements. On the other hand, the semi-simulation system is less affected by temperature changes, and at the maximum allowable temperature dif-ference of the equipment, the maximum phase noise error in the simulated signal is 2.12%. Therefore, based on the influence of phase noise variation on the accuracy of satellite signal simulation, nec-essary environmental conditions for AECS test are obtained, including the temperature consistent with the maximum operating temperature of the vector generator and the vibration Power Spectral Density (PSD) lower than 1.2gRMS.

It has been known that the performance of the High-Pressure Grinding Rolls (HPGR) varies as a function of method used to confine laterally the rolls, their diameter/length (aspect) ratio as well as their condition, if new or worn. However, quantifying these effects through direct experimentation in machines with reasonably large dimensions is not straightforward given the challenge, among others, of guaranteeing that the feed material remains unchanged. The present work couples the discrete element method (DEM) to multibody dynamics (MBD) and a novel particle replacement model (PRM) to simulate the performance of pilot-scale HPGRs grinding pellet feed. It shows that rotating side plates, in particular when fitted with studs, allow reaching more uniform forces along the bed, which also translates in a more constant product size along the rolls as well as higher throughput. It also shows that the edge effect is relatively constant with roll length, leading to substantially larger proportional edge regions for high-aspect ratio rolls. On the other hand, the product from the center region of such rolls was found to be finer when pressed at identical specific forces. Finally, rolls were found to have higher throughput, but generate a coarser product when worn following the commonly observed trapezoidal profile. The approach used in industry to compensate for roller wear by increasing the specific force and roll speed has then been demonstrated to be effective to maintain and potentially even increase product fineness and throughput, as long as the minimum safety gap is not reached.

This paper presents results from numerical and experimental investigation on Charpy tests in order to point out failure mechanisms and to evaluate new polymeric blends PP+PA6+EPDM. Charpy tests were done for initial velocity of the impactor of 0.96 m/s and its mass of 3.219 kg and these data were also introduced in the finite element model. The proposed model take into account the system of four balls, including support and the ring of fixing the three balls and it has a finer discretization of the impact area to highlight the mechanisms of failure and their development in time. The constitutive models for four materials (polypropylene with 1% Kritilen, two blends PP+PA6+EPDM and a blend PA6+EPDM) were derived from tensile tests. Running simulations for each constitutive model of material makes possible to differentiate the destruction mechanisms according to the material introduced in the simulation, including the initiation and the development of the crack(s), based on equivalent plastic strain at break (EPS) for each material. The validation of the model and the simulation results was done qualitatively, analysing the shape of broken surfaces and comparing them to SEM images and quantitatively by comparing the impact duration, energy absorbed by the sample, the value of maximum force during impact. The duration of the destruction of the specimen is longer than the actual one, explainable by the fact that the material model does not take into account the influence of the material deformation speed in Charpy test, the model being designed with the help of tests done at 0.016 m/s (1000 mm/min) (maximum strain rate for the tensile tests). Experimental results are encouraging for recommending the blends 20% PP+42% PA6+28% EPDM and 60% PA6+ 40%EPDM as materials for impact protection at low velocity (1m/s). Simulation results are closer to the experimental ones for the more brittle tested materials (with less content of PA6 and EPDM) and more distanced for the more ductile materials (with higher content of PA6 and EPDM).

Curcumin is one of the bioactive metabolites of turmeric (Curcuma longa), known for its pleiotropic pharmacological actions, including antioxidant and anti-inflammation, anticholinesterase, immunomodulation, and neuroprotection. Substantial evidence suggests the therapeutic benefits of curcumin against neurodegenerative disorders, including Alzheimer’s disease (AD), acting on a diverse array of brain targets that make the molecular mechanisms complicated. System biology level-investigation could potentially present a comprehensive molecular mechanism to delineate the neuropharmacological action of curcumin. In this study, we used integrated system pharmacology and molecular simulation analysis to gain insights into the underlying mechanism of curcumin action against AD. Network pharmacology study identified curcumin-targeted potential cellular pathways such as phosphatidylinositol 3-kinase/protein kinase B (PI3K/Akt) signaling, neurotrophin signaling, toll-like receptor (TLR) signaling, and autophagy, and proteins such as tropomyosin receptor kinase B (TrkB), liver X-receptor-beta (LXR-β), estrogen receptor-β (ER-β), mammalian target of rapamycin (mTOR), TLR-2, N-methyl-D-acetate receptor subunit 2B (GluN2B), β-secretase and glycogen synthase kinase-3β (GSK-3β), which are intimately associated with neuronal growth and survival, immune response, and inflammation. Moreover, the molecular modeling further verified that curcumin showed a significant binding affinity to mTOR, TrkB, LXR-β, TLR-2, ER-β, GluN2B, β-secretase, and GSK-3β, which are the crucial regulators of molecular and cellular processes associated with AD. Together, the present system pharmacology and in silico findings demonstrate that curcumin might play a significant role in modulating AD-pathobiology, supporting its therapeutic application for the prevention and treatment of AD.

Pore fluid pressure is very important to the generation, migration and accumulation of petroleum. The previous studies indicate that the Chezhen sag region is typically characterized by pore fluid overpressure (the difference between pore fluid pressure and hydrostatic pressure). To date, the formation mechanism of pore overpressure and the accumulation regularity of “upper source-lower reservoir” type in this region remains unknown. In order to investigate these problems, a 2-D finite element model is established with regards to the fluid-solid coupling in Chegu 25 block of Chezhen depression, fully considering the existing seismic, logging data and regional tectonic stress environment. Meanwhile, we calculate the abnormal overpressure generated at the source rock during hydrocarbon generation and the process of hydrocarbon migration and accumulation along the faults, analyzing the dynamic conditions of hydrocarbon downward accumulation. The results show that overpressure can accelerate migration of hydrocarbon and improve the efficiency of hydrocarbon accumulation. However, when the overpressure is too large, tensile fractures and shear fractures may occur, resulting in hydrocarbon dissipation, and changing the results of oil and gas accumulation. The overpressure at the source rock is mainly caused by hydrocarbon generation, while the overpressure at the reservoir is primarily created by unbalanced compaction. As the dominant channel of hydrocarbon migration, overpressure will change the direction and path of hydrocarbon migration in the fault. Therefore, the “upper source-lower reservoir” hydrocarbon accumulation model is strongly explained by the high permeability of faults and the presence overpressure. In summary, the simulated overpressure results are in good agreement with the mud weight equivalent overpressure and the drill stem tests (DSTs).

The paper explores the features of numerical simulation to analyze the dynamic behavior of drives controlled by pulse-width modulators. Modern motor control systems widely use pulse width modulation. Effective numerical modeling of such systems has specific features because the models employed are continuous-event and have hybrid behavior due to the presence of nonlinear links with discontinuities of the first kind. Therefore, it is essential to have special integration methods with variable steps, which should be factored in when developing the model. The paper shows how these problems are solved when modeling an electric drive with a DC motor in the SimInTech software.

Eruca sativa is a commonly used edible plant in Italian cuisine. E. sativa 70% ethanol extract (ES) was fractionated with five organic solvents. Ethyl acetate fraction(EEA) had the highest antioxidant activity, which was correlated with the total polyphenol and flavonoid content. ES and EEA acted as PPAR-α ligands by PPAR-α competitive binding assay. EEA significantly increased cornified envelope formation as a keratinocyte terminal differentiation marker in HaCaT cells. Further, it significantly reduced nitric oxide and pro-inflammatory cytokines in lipopolysaccharide-stimulated RAW 264.7 cells. The main flavonol forms detected in high amounts from EEA are mono-, and di-glycoside of each aglycone. Flavonol mono-glycosides were shown to be a potent PPAR-α ligand using molecular docking simulation and showed the inhibition of nitric oxide. These results suggest that E. sativa is suitable for use in improving skin barrier function and inflammation in skin disorders, such as atopic dermatitis.

This work aims at improving surface integrity and LCF life of machined Inconel 718. The correlation between the LCF life of Inconel 718 and various states of machined surface integrity is explored. In this paper, the surface integrity of Inconel 718 specimens is enhanced by low plasticity burnishing (LPB). The LCF life with different surface integrity specimens is predicted by micro-macro finite element method (FEM). Firstly, the LCF specimens with different surface integrity are machined by turning (turned specimen), polishing (matrix specimen) and LPB process (LPBed specimen). Secondly, the LCF experiment is carried out to reveal the effect of surface integrity on LCF life. Finally, the LCF micro-macro FEM model is proposed to predict the LCF of machined Inconel 718 specimens. The representative volume element (RVE) model is established based on the measured surface integrity and microstructure of Inconel 718 specimens. The effect of surface integrity on LCF life is transformed to equivalent load. The micro-macro FEM model combined with Tanaka-Mura dislocation crack initiation theory and extended finite element method (XFEM) is applied to predict the LCF life the machined specimens. The study results show that the LCF life of LPBed specimens can be improved by 90.5% and 36.1% compared with that of turned specimens and polished matrix specimens, respectively. The errors between FEM prediction results and experimental results are 13.1%, 9.2% and 12.2%, respectively. The proposed micro-macro FEM model could be utilized to predict the LCF life of Inconel 718 with different surface integrity, and further to apply the LCF life prediction in industry.

The concerning rise in emergence and prevalence of resistant strains to drugs of M. tuberculosis has ,the prompted researchers to look for new and effective treatments. With this motive, biscoumarins were identified as the lead molecules on a whole-cell-based screening of several less explored low molecular weight bioactive compounds against M. tuberculosis strains. Among the screened biscoumarins, the highest dock score derivatives were synthesized (a-h) using a programmable microwave synthesizer for better yields and reaction control. The synthesized derivatives were evaluated against H37Rv, H37Ra, M. smegmatis, an MDR surrogate model, and other bacterial strains for the structure-activity response. Assessment of the synthesized library against mycobacterial strains led to the identification of compounds (f and d) as lead anti-tuberculosis agents. Compounds (f and d) exhibited less toxicity against human cell lines. At the same time, it displayed enjoyable activity wherein MIC concentrations were observed to be 16- and 32 µg/mL against the susceptible H37Rv, and H37Ra strains of M. tuberculosis and MIC value of 128 µg/mL for M. smegmatis, respectively. For mechanistic insights and identification of drug binding targets, molecular docking and dynamic simulations were employed for a panel of 16 mycobacterial enzymes essential for mycobacterial growth and survival. These in silico studies revealed the DprE1 enzyme as a druggable target for the anti-tuberculosis activity of the selected biscoumarins derivatives. Further investigation is underway in our laboratory, leading to its development as an anti-tuberculosis drug (animal model studies).

Volcanism powered by tidal forces inside celestial bodies can provide enough energy to keep important solvents for living systems in the liquid phase. Moreover, tidal forces and their environmental consequences may strongly influence habitability of planets and other celestial bodies and may result in special forms of live and living conditions. A prerequisite to calculate such tidal interactions and consequences is depending on simulations for tidal accelerations in a multi-body system. Unfortunately, from measurements in many extrasolar planetary systems only few physical and orbital parameters are well enough known for investigated celestial bodies. For calculating tidal acceleration vectors under missing most orbital parameter exactly, a simulation method is developed that is only based on a few basic parameters, easily measurable even in extrasolar planetary systems. Such a method as being presented here, allows finding a relation between the tidal acceleration vectors and potential heating inside celestial objects. Using values and results of our model approach to our solar system as a “gold standard” for feasibility allowed us to classify this heating in relation to different forms of volcanism. This “gold standard” approach gave us a classification measure for the relevance of tidal heating in other extrasolar systems with a reduced availability of exact physical parameters. We would help to estimate conditions for the identification of potential candidates for further sophisticated investigations by more complex established methods like viscoelastic multi-body theories. As a first example, we applied the procedures developed here to the extrasolar planetary system TRAPPIST-1 as an example to check our working hypothesis.

The decreasing width, increasing aspect ratio RDL presents significant challenges to design for reliability (DFR) of advanced package. Therefore, this paper proposes a ML based RDL modeling and simulation method. In the method, RDL is divided into blocks and subdivided into pixels of metal percentage, and the RDL is digitalized as tensors. Then, an ANN-based surrogate model is built and trained by a subset of tensors to predict the equivalent material properties of each block. Lastly, all blocks are transformed into elements for simulations. For validation, line bending simulations were conducted on an RDL, with the reaction force as accuracy indicator. The results show that neglecting layout impact causes critical errors as substrate thins. By the method, the reaction force error is 2.81% and the layout impact can accurately be considered with 200×200 elements. For application, the TCT maximum temperature state simulation was conducted on a CPU chip. The simulation indicates that for advanced package the maximum stress more likely occurs in RDL rather than bumps, both RDL and bumps are critical impacted by layouts, and RDL stress is also impacted by vias/bumps. The proposed method precisely concerns layout impacts with little resources, presents an opportunity of efficiency improvement.

During the recent decades, global warming by greenhouse gas evolution has attracted worldwide attention and evermore strict regulations thereon have become institutionalized as international policies. In the process, more environment-friendly power generation technologies have been developed utilizing fossil fuels with a view to timely commercialization. As one of such “clean coal” technology, Integrated Gasification Fuel Cell system is a promising power generation means and COS hydrolysis reactor is installed downstream of coal syngas to remove acidic gas constituents such as H2S and COS. The most significant design parameters affecting performance of the COS hydrolysis reactor were selected to be GHSV, (catalytic) reaction temperature, and length ratio and numerical modeling was performed considering heat and fluid flow transfer as well as chemical reaction kinetics. Effect of the selected design parameters on the variation of conversion rate and reactant gas mixture concentration were comprehensively investigated to predict performance of COS hydrolysis reactor. Stochastic modeling of reactor performance was finally performed using Monte Carlo simulation and linear regression fitting.

This study investigated riverbank protection strategies along the dynamic Jamuna River in Bangladesh, a braided river prone to erosion and sedimentation. It reviews past countermeasures and emphasizes the effectiveness of groyne-type structures in redirecting flow and preventing erosion. Notably, the left bank exhibited greater stability than the right bank, emphasizing the need for effective groyne installations. A systematic methodology utilizing numerical modeling using International River Interface Cooperation (iRIC Nays2DH) ensured accuracy in assessing morphological impacts. This study presents novel countermeasures incorporating groyne installations in Zone 1 (from Singrabari to Meghai) and Zone 2 (from Pachthakuri to Subhagacga), accompanied by simulations for various flood conditions. Zone 2, identified as highly erosion-vulnerable, showed the greatest susceptibility. Simulations (Cases_0 1, 2, and 3) revealed groynes in Zone 1 alone ineffective, while Zone 2 installations successfully diverted oblique flow, reducing erosion risk. Although Case_3's combined approach was effective, it was uneconomical for Zone 1. Case_2, focusing on Zone 2 groynes, emerged as the optimal solution, redirecting flow and shaping sandbars to mitigate Jamuna River's riverbank erosion. It provides a practical and economical solution. Further research is recommended for groyne length and spacing variations. This study enhances Jamuna River protection, emphasizing groyne-type structures' importance and promoting a holistic understanding of morphological dynamics for future river management and effective countermeasures.

Our aim is to provide an insight of the procedures and the dynamics that lead the spread of contagious diseases through populations. Our simulation tool can increase our understanding on the spatial parameters which affect the diffusion of a virus. SIR models are based on the hypothesis that populations are “well mixed”. Our model constitutes an attempt to focus on the effects of the specific distribution of the initially infected individuals through the population and provide insights, considering the stochasticity of the transmission process. For this purpose, we represent the population using a square lattice of nodes. Each node represents an individual that may or may not carry the virus. Nodes that carry the virus can only transfer it to susceptible neighboring nodes. This important revision of the common SIR model provides a very realistic property: the same number of initially infected individuals can lead to multiple paths, depending on their initial distribution in the lattice. This property creates better predictions and probable scenarios to construct a probability function and appropriate confidence intervals. Finally, this structure permits realistic visualizations of the results to understand the procedure of contagion and spread of a disease and the effects of any measures applied.

Flood events are becoming more severe, causing significant problems to human communities, including physical, psychological, and material damage. For both flood forecasting in emergency response situations and flood mapping, georeferencing and data curation are paramount in the context of prevention or preparedness. Hence, data display, data management, and articulation with numerical simulation results must occur on GIS platforms. Our research is motivated by recent advances in Web and GIS technologies, social sensing and high-performance computing, and an envisaged wider availability of remote sensing data. This paper presents and discusses an innovative Web GIS platform named "RiverCure Portal" or "RCP" for short. This platform combines observations and hydrodynamic modelling tools to support various stages of the flood risk management cycle, including operational response, emergency preparedness, and risk assessment. RCP is a multi-organisation, multi-context digital platform with flexible configuration features to define and support multiple sensor types and modelling options, satisfying the various needs of different organisations and stakeholders. In addition, this paper discusses the RiverCure Approach, which encompasses the following tasks directly supported by the RCP platform: defining the context and involved geometries, associating sensors to the context, pre-processing and generating the context mesh, defining the simulation event, running the simulation event, and analysing the results from the simulation event. Thus, the RCP streamlines and simplifies data analysis and simulation procedures to meet decision-makers' needs. The novelties discussed in this paper include the design and discussion of a Web GIS platform that allows (i) to manage flood data and results of simulations at several contextual levels by different stakeholders such as domain experts, decision-makers, researchers, or students; (ii) to process and curate sensed data obtained from physical and social sensors; and (iii) update the state and values of the parameters of simulation tools through continuous data assimilation techniques for forecasting purposes. Finally, this paper supports the explanation and discussion with a running example, "Águeda 2016 flood" event, which dataset is publicly available for further study and experimentation.

This paper presents an analysis of the sensitivity of controlling an autonomous surface object among a group of encountered objects to the inaccuracy of state control process data. For this purpose, a safe and optimal model of the control process was defined. An algorithm for determining the optimal and safe trajectory of an object, based on the multi-object game model, was developed; for comparative analysis, an algorithm for calculating only the optimal trajectory, not taking into account the maneuverability of other objects, was additionally developed. First, simulation-based studies of the algorithms enabled a comparative analysis of a number of different acceptable strategies for optimally shifting the trajectory of maneuvering objects from a single initial direction. Thereafter, the main goal of this paper was implemented: an analysis of the sensitivity characteristics of safe control, assessed with the risk of collision, both on the inaccuracy of navigation data and on the number of possible control strategies. Finally, final conclusions and a plan for further research on the subject of the paper were formulated.

The current work investigates the auxetic tensile deformation behavior of the inversehoneycomb structure with 5 × 5 cells made of biodegradable poly(butylene adipate-coterephthalate) (PBAT). Fused deposition modeling, an additive manufacturing method, produced such specimens. Residual stress (RS) and warpage, more or less, always exist in such specimens due to layer-by-layer fabrication, i.e., repeated heating and cooling. The RS influences the auxetic deformation behavior, but its measurement is challenging due to the very fine structure. Instead, the finite-element(FE)-based process simulation realized by an ABAQUS plug-in numerically predicts the RS and warpage. The predicted warpage shows a negligible slight deviation compared to the design topology. This process simulation also delivers the temperature evolution of a small volume material, revealing the local cyclic heating and cooling. The achieved RS serves as the initial condition for the FE model used to investigate the auxetic tensile behavior. With the outcomes from FE calculation without considering RS at hand, the effect of the RS on the deformation behavior is discussed for the global force-displacement curve, the structural Poisson’s ratio evolution, the deformed structural status, the stress distribution, and evolution, where the first three and the warpage are also compared with experimental results. Furthermore, the FE simulation can easily provide the global stress-strain flow curve with the total stress calculated from the elemental ones.

Supramolecular solvent (SUPRAS) has received increasing interest as an innovative, efficient, and green solvent for the effective extraction and separation of bioactive compounds from natural resources. However, studies on the use of SUPRAS for the extraction of phenolic components from plants, which are highly valued in food products due to their excellent antioxidant capacity, are still lacking. The present study developed a green ultrasound-assisted and efficient SU-PRAS method to simultaneously determine three phenolic acids in Prunella vulgaris by high-performance liquid chromatography (HPLC) and the experimental parameters were optimized in detail. The efficiency and antioxidant properties of the phenolic compounds obtained by different extraction methods were also compared. Under the optimal conditions, the extraction efficiency of SUPRAS, prepared with octanoic acid reverse micelles dispersed in ethanol-water, was substantially higher than conventional organic reagents. Moreover, this SUPRAS method also showed more significant antioxidant capacities. The confocal laser scanning microscopy (CLSM) images presented the spherical droplet structure of SUPRAS (A well-defined circle), which coincided with the position of the fluorescence position of phenolic acids. The phenolic acids were encapsulated in the vesicles by the SUPRAS droplets, which indicated the efficient extraction capacities of SUPRAS for the target compounds. Finally, combined with the CLSM method, the mechanism of the proposed method was further clarified, and the superior extraction performance of SUPRAS was theoretically demonstrated through molecular dynamics simulations. In comparison with conventional methods, the higher extraction efficiency of SUPRAS can be illustrated by the larger solvent contact surface area, more types of hydrogen bonds between extractants and supramolecular solvents, and stronger and more stable interaction forces. The results of the theoretical studies are in rational agreement with the experimental outcome.

A novel physiologically based algorithm (PBA) for the computation of fractional flow reserve (FFR) in coronary artery trees (CATs) using computational fluid dynamics (CFD) is proposed and developed. The PBA is based on the extension of Murray's law and additional inlet conditions prescribed iteratively, and is implemented in OpenFOAM for testing and validation. 3D models of CATs are created using CT scans and computational meshes, and the results are compared to in-vasive coronary angiographic (ICA) data to validate the accuracy and effectiveness of the PBA. The discrepancy between calculated and experimental FFR is within 2.33-5.26% in steady-state and transient simulations, respectively, when convergence is reached. The PBA is a reliable and physiologically sound technique compared to the current lumped parameter model (LPM), which is based on empirical scaling correlations and requires nonlinear iterative computing for conver-gence. The accuracy of the PBA method is further confirmed using the FDA nozzle, which demonstrates good alignment with CFD-validated values.

Cycle times at workstations in offsite construction factories fluctuate widely due to various influencing factors. Consequently, relying on average rates, such as length per unit of time, for estimating cycle times proves to be inaccurate, often leading to significant deviations between production schedules and actual operations. To address this issue, this study proposes an estimation system that leverages machine-learning-based prediction, statistical methods, 3D simulation, and computer vision to predict cycle times at the workstation level. Testing of the system on a semi-automated wood-wall framing workstation in a panelized construction factory shows that it reduces the mean absolute error and sum of errors by approximately 36% and 68%, respectively, compared to the fixed rate method. The results also highlight the efficacy of using computer vision data for training machine-learning models for cycle time estimation, the importance of identifying and understanding the factors influencing cycle times, and the impact of random delays on the accuracy of cycle time estimation systems.

This study investigates the effect of Re addition on the microstructure evolution and oxidation resistance of Co-Cr-Ta-Ti-C alloys. The alloys tested in this study consist of a Co-rich matrix with mixed HCP and FCC phases, together with TaTiC2 and Ti-based carbides. The addition of Re promotes the precipitation and growth of a CoCr-rich σ phase. Differential thermal analysis (DTA) showed that the melting temperatures did not change drastically up to 10 at% Re addition, whereas 15 at% Re addition significantly increased the melting temperature of the alloys. Oxidation tests in air at 1200°C showed that excessive Re content could lead to deterioration in oxidation resistance, mainly due to the accelerated formation of volatile Re oxides.

Considering the need to reduce greenhouse gas emissions, onshore wind energy is certain to play a major role in future energy systems. This topic has received significant attention from the research community, producing many estimations of Europe's onshore wind potential for capacity and generation. Despite this focus, previous estimates have relied on distribution assumptions and simulation schemes that summarily under predict both the amount of available future wind capacity as well as its performance. Foremost in this regard is the common use of contemporary, or at least near-future, turbine designs which are not fitting for a far-future context. To fulfill this role, an improved, transparent, and fully reproducible work flow is presented for determining European onshore wind potential. Within a scenario of turbine cost and design in 2050, 13.5 TWof capacity is found to be available, allowing for 34.4 PWh of generation. By sorting the explicitly-placed potential generation locations by their expected generation cost, national relations between turbine cost and performance versus a desired capacity are exposed. In this way, it is shown that all countries possess some potential for onshore wind energy generation below 4 €_ct kWh^-1. and, furthermore, that it is unlikely for these costs to exceed 6 €_ct kWh^-1.

This paper adopts a systems firm-centered perspective on the environmental assessment of recyclable glass and PET soft drink containers. We employ LCA and discrete-event simulation modelling for the environmental assessment of the two soft drinks packaging alternatives in operational terms, over the entire supply chain, over a period of three years. The assessment is based on real data collected from a large soft-drinks producer and its suppliers. The research and practice contribution of the paper is twofold: first, it introduces a methodological framework for environmental assessment of companies’ packaging environmental impact under different product and operations strategies, and secondly, it provides a holistic environmental assessment of the two packaging materials (PET and glass) taking into account specific operational issues, such as product mix and recycling and reuse options, and activity interdependences and stochasticity. The results of the simulation experiments confirm at system level, for glass, the importance for sustainability, to increase the number of reuse cycles and the percentage of used bottles collected for refilling, whereas for PET, to increase the percentage of recycled PET in new bottles.

Different inlet structures have a significant impact on the internal flow characteristics of a solid-magnesium powder water ramjet engine. Based on the magnesium-water reaction model, a computational fluid dynamics (CFD) method is applied to establish a numerical simulation method for the internal flow field of the engine, and the internal flow characteristics of the engine under different inlet structure conditions are studied. The simulation results show that high-temperature gas can effectively promote the ignition of magnesium powder at the top of the combustion chamber, while accelerating the evaporation of the first inlet water and increasing the combustion rate of magnesium powder. The secondary inlet has the most significant effect on the temperature inside the combustion chamber. When the secondary inlet flow rate increases towards the top of the combustion chamber, it increases the amount of heat absorbed by the evaporating water at the top of the chamber, thereby reducing the temperature at the top of the combustion chamber. However, when the flow rate is low, it results in insufficient oxidizer at the top of the combustion chamber, which is unfavorable for the combustion of magnesium powder.

The stick-free flight stability is an old-fashioned and non-progressive issue; nevertheless, it is still existent, and of significant importance to the design of aircraft whose control system is reversible. The problem’s existence necessitates a deep assessment of stick-free flight stability throughout the aircraft design. Up to now, this problem has been addressed using either analytical approaches, which are only related to the static stability evaluation, or performing flight tests. In this study, the problem is handled in its entirety, from static and dynamic flight stability assessment to design criteria with a comprehensive perspective. Moreover, it is also exhibited that contrary to what has been generally proposed in the literature, limiting the problem of stick-free flight stability through static stability assessment is far from the main challenge. As a brief scope, the derivation of the control surface dynamics, a stick-free trim algorithm, and assessment rationale of the stick-free static and dynamic flight stability using a simulation approach are proposed. As a consequence, the aim is to set a broad understanding for designers related to this phenomenon and add adjunct design criteria in the design optimization process by approaching it in terms of modeling, simulation, and flight test perspective.

We review and assess the classic SIR and SEIR epidemiological models regarding possible applications to the COVID-19 pandemic. In spite of numerous more complicated models, we show how the qualitative features of the solution to the SIR and SEIR models continue to provide valuable public health insights in some scenarios. Using estimated COVID-19 data as of this date, the SEIR model shows that if it were possible to reduce R₀ from 2.5 to 1.25 through social distancing and other measures, the maximum fraction of the population that would become infected at any particular time would drop from 17% to 4%, provided that all of the model assumptions are satisfied. Finally, we compare the classic SIR model with a recent stochastic model with favorable results. Since this comparison underscores the importance of underlying connectivity assumptions, we conclude with Monte-Carlo simulations with specific connectivity that reproduce the classical SIR model with standard incidence.

We estimated the daily intakes of chlorpyrifos and cypermethrin via ingestion of indoor dust and outdoor soils using the Stochastic Human Exposure and Dose Simulation Model on a probabilistic approach for Taiwan’s homes. Variable information for the daily intake estimation, such as concentration, ingestion rate, body weight, was adopted from previous studies. Monte Carlo simulation was performed with 1,000,000 iterations to simulate a single daily intake, which was shown in terms of percentage of the Acceptable Daily Intake (ADI) of either insecticide. The daily intakes were minimal with a 99% probability; at 99.9th percentile, however, the total intakes leaped to 13.1% and 20.0% of the respective ADIs of chlorpyrifos and cypermethrin. The sensitivity analysis indicated that concentration was the most determinant variable. Compared to the data of daily intakes via dietary ingestion of vegetables derived from a previous study, the estimated intakes by this study were considerable at the highest percentile, which referred to insecticide residues few days after insecticide application. Consequently, the non-dietary ingestion exposure to either insecticide was negligible in most cases; nevertheless, for those with indoor insecticide applications, the daily intakes for young children could be of concern. Frequently home cleaning is recommended to reduce the exposure.

The entry and exit method is a simple and practical method to determine the critical slip surface of slope. However, it has the drawback of sacrificing computational efficiency to improve search accuracy. To solve this problem, this paper proposes an improved entry and exit method to search for the critical slip surface. Based on the random fields generated by using Karhunen–Loève expansion method, the simplified Bishop’s method combined with the improved entry and exit method is used to determine the critical slip surface and its corresponding minimum factor of safety. Then, the failure probability is calculated by conducting Monte Carlo simulation. Two examples are reanalyzed to verify the accuracy and efficiency of the proposed method. Meaningful comparisons are made to demonstrate the calculating accuracy and calculating efficiency of the improved entry and exit method in searching for the minimum safety factor of slope, based on which the effect of the reduced searching range on slope reliability was explored. The results indicate that the proposed method provides a practical tool for evaluating the reliability of slopes in spatially variable soils. It can greatly improve the computational efficiency in relatively high-computational accuracy of slope reliability analysis.

Accurate analysis of continuous-wave electron spin resonance (cw ESR) spectra of biological or organic free-radicals and paramagnetic metal complexes is key to understand their structure-function relationships and electrochemical properties. Current method of analysis based on simulations often fail to extract the spectral information accurately. In addition, such analyses are highly sensitive to spectral resolution and artifacts, users’ defined input parameters and spectral complexity. We introduce a simulation-independent spectral analysis approach that enables broader application of ESR. We use a wavelet packet transform-based method for extracting g values and hyperfine (A) constants directly from cw ESR spectra. We show that our method overcomes the challenges associated with simulation-based methods for analyzing poorly / partially resolved and unresolved spectra, which is a common in most cases. The accuracy and consistency of the method are demonstrated on a series of experimental spectra of organic radicals and copper-nitrogen complexes. We showed that for a two-component system, the method identifies their individual spectral features even at a relative concentration of 5% for the minor component.

Current industrial robotic manipulators have made evident their lack of flexibility. The systems must know beforehand the piece and it’s position. To address this issue, contemporary approaches typically employ learning-based techniques, which rely on extensive amounts of data. To obtain vast data, an often sought tool is an extensive grasp dataset. This work introduces our Physics-Based Self-Supervised Grasp Pose Detection (PBSS-GPD) pipeline for model-based grasping point detection, useful to generate grasp pose datasets. Given a gripper-object pair, it samples grasping pose candidates using a modified version of GPD (implementing inner-grasps, CAD support...) and quantifies their quality using the MuJoCo physics engine and a grasp quality metric that takes into account the pose of the object over time. The system is optimised to run on CPU in headless-parallelised mode, with the option of running in a graphical interface or headless and storing videos of the process. The system has been validated obtaining grasping poses for a subset of Egad! objects using the Franka Panda two-finger gripper, compared with state of the art grasp generation pipelines and tested in a real scenario. While our system achieves similar accuracy compared to a contemporary approach, 84% on the real world validation, it has proven to be effective at generating grasps with good centering 18 times faster than the compared system.

It is well-known that simulation tools are essential for the design and optimization of wireless communication systems. In this paper proposes a python script that can be used for planning and predicting a connection link budget by analyzing its basic parameters. Our proposal consists of an application that calculates the connection budget for point-to-point links operating at 5 GHz, taking into account all the necessary microwave parameters. For validating the efficiency of the proposed tool, the paper presents comprehensive simulation results derived from comparing our tool to a couple of other simulation tools by means of calculating the same parameters.

This paper concentrates on computing the efficiency of heliostat field systems. By conducting a comprehensive analysis of the mathematical model for optical efficiency, we have effectively simplified the complex three-dimensional illumination problem of heliostat fields into a two-dimensional issue. Our work primarily investigates the calculation methods for the average optical efficiency and output power of heliostat. Traditionally, calculating shadow and blocking efficiency, key factors affecting the optical performance of mirror fields, has posed a significant technical challenge. Through innovative improvements to the Monte Carlo simulation technique, this study has successfully reduced the spatial dimensionality of the problem. We employed a series of novel coordinate transformations to simulate light tracing on a two-dimensional plane, thereby efficiently calculating the efficiency of shadows and obstructions. Not only have we solved the computational challenges of shadow and obstruction efficiency, but our unique algorithm design also allows us to precisely obtain the overall average optical efficiency of the heliostat field while enhancing computational efficiency.

A review of the published quantitative risk assessment (QRA) models of L. monocytogenes in seafood was performed, with the objective of appraising the effectiveness of the control strategies placed along the food chain. Whereas all the 13 QRA models retrieved were of short scope, covering at most from end of processing to consumption; the majority (85%) focused on smoked or gravad fish. Since the modelled pathways commenced with the packaged product, none of the QRA models addressed cross-contamination events. Many models agreed on the fact that keeping the product’s temperature at 4.0-4.5 ºC leads to greater reductions in the final risk of listeriosis than reducing the shelf life by one week; and that the effectiveness of both measures can be surpassed by reducing the initial occurrence of L. monocytogenes in the product (at the end of processing). It is therefore necessary that future QRA models for RTE seafood contains a processing module that can provide insight into intervention strategies that can retard L. monocytogenes growth, such as the use of bacteriocins, ad-hoc starter cultures and/or organic acids, and other strategies seeking to reduce cross-contamination at the facilities, such as stringent controls for sanitation procedures. Since risk estimates were shown to be moderately driven by growth kinetic parameters, namely, the exponential growth rate, the minimum temperature for growth, and the maximum population density, further work is needed to reduce uncertainties about them.

The aim of this study is to present a method for developing fragility curves for soil liquefaction that are consistent with the seismic hazard using Monte Carlo simulation. This method can account for all the uncertainties and variabilities of the input parameters. The seismic parameters of earthquake magnitude (M) and the associated peak ground acceleration (PGA) are considered together for the liquefaction assessment. The liquefaction potential and damages obtained by this method are more realistic. A case study is performed using data from a sand-boil site in Yuanlin, Changhua county, where liquefaction occurred during the Chi-Chi earthquake in Taiwan in 1999. The results show that the liquefaction potential index, IL, the post-liquefaction settlement, St, and the liquefaction probability index, PW, are all suitable parameters for evaluating the liquefaction damages. The fragility curves for soil liquefaction developed by this method can support the performance-based earthquake engineering (PBEE) approach, provide guidance for liquefaction evaluation to the ‘Taiwan Earthquake Loss Estimation System’-TELES, and serve as a basis for scenario simulation and an earthquake early warning system for liquefaction damages.

The problem of intensification of melt crystal growth process has been analyzed using CdTe as an actual material. Numerical simulation of 100 mm diameter CdTe crystal growth by VGF technique has been carried out. The heat-mass transfer was controlled by introducing of low-frequency oscillating baffle into the melt, so called axial vibrational control (AVC) technique. The baffle configuration has been optimized to destroy solid «tails», which were formed near the crucible walls at high cooling rates due to the low thermoconductivity and the corresponding latent heat. Analysis of CdTe homogeneity range showed that during fast crystal cooling Te micro precipitations were formed resulting from decay of oversaturated Cd-riched nonstoichiometric solid solution at Bridgman crystal growth technique. A VGF grown CdTe crystal after full crystallization stays inside the phase field of the high temperature wurtzite polymorph. This makes it possible to go through the polymorph transition without Te micro-precipitating using the advantages of VGF specific feature of very slow cooling.

The accuracy of star position simulation is the key factor affecting the accuracy of ground calibration test of spacecraft attitude measurement system. To solve the impact of nonimaging polarized stray light on the simulation accuracy of star position in the optical engine of the system, the generation mechanism of non-imaging polarized stray light has been investigated, and an optimization method for polarization balance of the optical engine is proposed. The mathematical model of the incident light aperture angle and the ideal polarization parameter of the optical engine thin film is established, and the optimization evaluation function of polarization balance of the optical engine is constructed. An optical engine polarization balance film with the corresponding full-band binomial attenuation is <0.001 and the phase delay is <1°. Experimental results show that the simulation accuracy of the weak starlight simulation system is improved by 1.64 times using polarization balanced optical engine.

In this paper, four lithological parameters, i.e. thermal conductivity, particle size, porosity and saturation, are investigated by combining experimental observations with numerical simulations to study the influence laws and mechanisms of action on the combustion process of methane hydrate sediments. The variation of combustion characteristics parameters such as flame height, effective combustion ratio and dimensionless discharge water mass with the lithological parameters are studied. In addition, the combustion mechanism of lithologic parameters on methane hydrate deposits is revealed. Combining the experimental results and simulation calculations, to optimize the combustion of methane hydrate sediments, it is recommended to use methane hydrate sediment samples with high saturation and low thermal conductivity, while the oxidant concentration and porosity of methane hydrate sediment samples should be increased.

Road collisions are among the world’s critical issues causing many casualties, deaths, and economic losses. To deal with this scenario, precise analysis is required. In this paper, we use Machine Learning (ML) techniques to assess and predict road traffic collisions. An ensemble machine learning model with two layers was developed to analyze simulation data from the driving simulator. The first (base) layer integrates supervised learning techniques namely, k- Nearest Neighbors (k-NN) AdaBoost, Naive Bayes (NB), and Decision Trees (DT). The second layer predicts road collisions by combining the base layer outputs by employing the stacking ensemble method using logistic regression as a meta-classifier. The data for this study were imbalanced; therefore, we performed a SMOTE resampling strategy to handle the dataset imbalance. To simplify the model, the PSO algorithm was used to select the most important features in our dataset. The two-layer ensemble model proposed had the best outcomes with an accuracy of 88%, F1 score of 83%, and an AUC of 86% as compared with k-NN, DT, NB, and AdaBoost.

As a new logistics system, Physical Internet (PI) provides a solution to cope with the continuous rise of urban logistics demand by exploring same-level and cross-level paths and flattening. This research suggests a PI-based urban logistics distribution cost minimization model based on the examination of the primary elements influencing PI distribution, intending to maintain the logistic transportation process' integrity. This proposed model enhances the flexibility of goods operation and reduces the global cost of logistics distribution using the interconnected and open PI logistics distribution mode. The experimental results show that the distribution cost of the PI logistics model is significantly better than that of a traditional logistics model. The elastic and cost advantages relatively grow as the infrastructure for distribution scales up and the interruptions from emergencies occur.

In this study, we present different methods of estimating fuzzy reliability of a two-parameter Rayleigh distribution via the maximum likelihood estimator, median first-order statistics estimator, quartile estimator, L-moment estimator, and mixed Thompson-type estimator. The mean-square error MSE as a measurement for comparing the considered methods using simulation through different values for the parameters and unalike sample sizes is used. The results of simulation show that the fuzziness values are better than the real values for all sample sizes, as well as the fuzzy reliability at the estimation of the Maximum

Commonly, professors, students and researchers from universities around the world use software distributed under a license agreement for computer simulation purposes, which requires a computer with considerable hardware capabilities. Consequently, this implies a high cost to conduct simulations that require implementing numerical methods in all areas of engineering, particularly in the field of robotics and nonlinear control. This paper presents the design and results analysis of a low-cost and open-source frugal computer simulation tool with applications to robotic nonlinear control, for instance, for numerical simulations of manipulator robot control based on dynamic models. Using a single board minicomputer with with reduced computing power, Raspberry Pi, together with free software, GNU-Octave, trajectory tracking control simulations in the joint space of a Selective Conformal Assembly Robot Arm (SCARA) are achieved by solving a system of nonlinear differential equations, represented in matrix form, which includes the control law and the system model. The results of the proposed alternative are compared by running the same simulation code on a laptop computer using MATLAB and GNU Octave, which show minimal deviations and reasonable time complexity. Moreover, considering the frugality curve calculated for this approach, in addition to the low acquisition cost of the simulation software tool, it would allow the creation of a simulation laboratory in some universities with budgetary constraints for educational and research purposes.

Estimating peak flow for a catchment is commonly undertaken using the design event method, however this method does not allow for the understanding of uncertainty in the result. This research first presents a simplified method of fragments approach to rainfall disaggregation that ignores the need to consider seasonality, offering a greater diversity in storm patterns within the resulting sub-daily rainfall. By simulating 20 iterations of the disaggregated sub-daily rainfall within a calibrated continuous simulation hydrologic model, we were able to produce multiple long series of stream flow at the outlet of the catchment. With this data, we investigated the use of both the annual maximum and peaks over threshold approaches to flood frequency analysis and found that for a one in 100 year annual exceedance probability peak flow, the peaks over threshold method (333m3/s ±50m3/s) was significantly less uncertain than the annual maximum method (427m3/s ±100m3/s). For the one in 100 year annual exceedance probability, the median peak flow from the peaks over threshold method (333m3/s) produced an outcome comparable to the design event method peak flow (328m3/s), indicating that this research offers an alternative approach to estimating peak flow, with the additional benefit of understanding the uncertainty in the estimation. Finally, the paper highlighted the impact that length and period of streamflow has on peak flow estimation and noted that previous assumptions around the minimum length of gauged streamflow required for flood frequency analysis may not be appropriate in particular catchments.

For deep-penetrating geochemistry, there is a frontier issue as to how to explore ore-bearing information deep in covered areas, while it is, too, important to investigate the geochemical migration of ore-forming elements for the development of exploration geochemistry. In this study, a 380-day migration column experiment was conducted with surface soil and pure Cu powder collected from the Yujiashan study area in Wuhan City, Hubei Province taken as the object of research to simulate the migration process of ore-forming elements under natural conditions. The results showed obvious vertical migration of the ore-forming elements and conversion of mobile metal forms in the process; further, according to 6 groups of simulation experiments that took 45 days to conduct on migration column samples and the surface oil and Cu powder collected from the Pulang mining area in Yunnan Province, the vertical migration of the ore-forming element was still visible, and the exogenous substance (pure Cu powder) could enhance the anomaly without changing the basic migration mechanism. This indicates that Cu might migrate in a stable manner in soil cover in the Pulang mining area, and its migration was mostly driven by the transformation of Fe-Mn oxide bound state and organic bound state; finally, a multifractal analysis was conducted, revealing that the ore-forming elements presented a nonlinear and complex structure during their upward migration, which caused anomalies in the covered area, and multiple parameters exerted a certain indicative effect on different source intensities and properties of soil. In this study, laboratory simulations were performed to summarize the active-state evolution pattern and migration mechanism of ore-forming elements with a view to providing technical support and theoretical guidance for geochemical prospecting in the covered region.

To solve the problem of deformation and stress in segments when a full-face hard rock tunnel boring machine (TBM) tunnel for an urban subway passes through existing buildings, a three-dimensional mechanical calculation model of TBM tunneling under existing buildings was established based on numerical analysis to comprehensively study the spatial attributes of tunnel segments during TBM tunneling. The Qingdao Metro Line 1 TBM tunnel in the hard rock stratum of Xiaobei District passes through existing buildings. The results indicated that (1) the stress and deformation of the segments were different at different positions. The horizontal and vertical stress and displacement of the segments in front of the building were significantly affected by the building. When the segment was not in the area below the horizontal plane of the building, the vertical stress of the segment was significantly greater than the two stresses in the horizontal direction. (2) The vertical displacements of the vault and the arch bottom were the largest, and the influence of vertical accessories was stronger when the segment was closer to the building.(3) When the tunnel was excavated to approximately one tunnel diameter in front of the building, the building was affected. If the surrounding rock is unstable, the excavation face may collapse and the ground surface may sink, possibly leading to inclination, cracking, and uneven settlement of the building.

Wind energy is a rapidly expanding renewable energy technique. Wind farm developers need to understand the interaction between wind farms and the atmospheric flow over complex terrain. Large-eddy simulations provide valuable data for gaining further insight into the impact of rough topography on wind-farm performance. In this research, we investigate the influence of spatial heterogeneity on wind turbine performance. We conducted numerical simulations of a 12×5 wind-turbine array on various rough topographies. First, we evaluated our LES method through mesh convergence analysis, using mean vertical profiles, vertical friction velocity, and resolved and subgrid-scale kinetic energy. Next, we analyze the effects of surface roughness and dispersive stresses on the performance of fully developed large wind farms. Our results demonstrate that the ground roughness element’s flow resistance boosts large wind-farm power production by almost 68% in fully aerodynamic rough surface compared to flat terrain. Dispersive stress analysis revealed that the primary degree of spatial heterogeneity in the wind farm is in the streamwise direction, which is the “wake-occupied” region, and the relative contribution of dispersive shear stress is almost 45% to the overall drag. We also observed that the power performance of the wind farm in complex terrain outperforms the drag. Our study has implications for improving the design of wind turbines and wind farms in complex terrain to increase their efficiency and energy output.

High-fidelity patient simulation (HFPS) is widely used in professional training to enhance students’ competence in clinical management. Problem-solving (PS) and clinical reasoning (CR) skills are essential to developing students in professional competence in safe and effective care. These two skills should be initiated at the early training. However, little is known about the effects of HFPS on developing PS and CR skills in first year undergraduate students. Therefore, this pre- and post-experimental study aimed to investigate the effects of HFPS on development of PS and CR skills in first-year nursing students. The students were required to go through four sessions, preparation, pre-briefing and orientation, simulation role-playing, and debriefing, for the HFPS. The study utilized the Problem-Solving Inventory (PSI) and the Nurses Clinical Reasoning Scale (NCRS) to measure problem-solving and clinical reasoning abilities before and after HFPS. Bivariate analysis, one-sample t-test, and independent t-test were performed to evaluate the performance of the PS and CR skills at the two study periods. One hundred eighty-nine students were recruited, with a mean age of 20.56 years, and 73% were female students. The analytic results showed that the PSI, particularly in domains of Problem-Solving Confidence (PSC) (p&lt;0.001) and overall PS (p&lt;0.001), and the CR (p&lt;0.001) had significant improvement after HFPS. The study concluded that HFPS is an effective innovative method to significantly improve students’ problem-solving and clinical reasoning abilities. Nurse educators play an important role in providing explicit learning instructions in a simulation guideline that directs and guides students to learn at each stage of HFPS. Students should take more initiative and engage in their learning through HFPS to enhance their competence in knowledge and higher intellectual skills for personal and professional developments.