MnO₂ nanoparticles are considered nanozymes with intrinsic peroxidase-like activity and there are several reports on their application in the field of nanozyme-based sensing and detection, however, up to now, there is no report on the investigation of their biochemical and kinetics properties toward enzyme-mediated oxidations. Hence, in this work, the MnO₂ nanozymes were synthesized and characterized with different characterization methods. Thereafter, their biochemical properties including pH stability, thermal stability, and salt stability as well as their kinetics perfromances were evaluated toward n-electron irreversible oxidation of 3,3’-diaminobezedine. The results showed that the as-prepared nanozymes reveal their maximal enzyme-like activity over a wide pH range of 3.0-6.0 at a temperature of 23-25 ℃ toward oxidation of 3,3’-diaminobezedine. Besides, the salt stability studies exhibited that the as-mentioned nanozymes can save their maximal activity over a wide range of high salt concentrations over 3-7 M of NaCl. Moreover, the kinetics studies revealed a K_m as low as 1.6 mM and a V_max as high as 47 nM sec^-1 for the MnO₂ nanozymes toward irreversible oxidation of DAB to produce the brown-colored polyDAB.

The key to the practical application of organometal–halide–crystals perovskite solar cells (PSCs) is to achieve thermal stability through robust encapsulation. This paper presents a method to significantly extend the thermal stability lifetime of perovskite solar cells to over 5,000 h at 85 °C by demonstrating an optimal combination of encapsulation methods and perovskite composition for carbon–based multiporous–layered–electrode (MPLE)–PSCs. We fabricated the four types of MPLE-PSCs using two encapsulation structures (over– and side–sealing with thermoplastic resin films) and two perovskite compositions ((5–AVA)x(methylammonium (MA))1–xPbI3 and (formamidinium (FA))0.9Cs0.1PbI3), and analyzed the 85 ºC thermal stability followed by ISOS–D–2 protocol. Without encapsulation, FA0.9Cs0.1PbI3 exhibited higher thermal stability than (5–AVA)x(MA)1–xPbI3. However, encapsulation reversed the phenomenon (that of (5–AVA)x(MA)1–xPbI3 became stronger). The combination of (5–AVA)x(MA)1–xPbI3 perovskite absorber and over–sealing encapsulation effectively suppressed the thermal degradation, resulting in the PCE value at 91.2% of the initial value after 5,072 h. On the other hand, another combination (side–sealing on (5–AVA)x(MA)1–xPbI3, over– and side–sealing on FA0.9Cs0.1PbI3) resulted in decreased stability. The FA–based perovskite was decomposed for these degradation mechanisms by the condensation reaction between FA and carbon. For side–sealing, the space between the cell and the encapsulant was estimated to contain approximately 1,260,000 times more H2O than in over–sealing, which catalyzed the degradation of the perovskite crystal. Our results demonstrate that MA–based PSCs, which are generally considered to be thermally sensitive, can significantly extend their thermal stability after the proper encapsulation. Therefore, we emphasize that finding the appropriate combination of encapsulation technique and perovskite composition is quite important to achieve further device stability.

Castor oil may be differentiated from other non-edible vegetable oils because of its main composition of hydroxylated fatty acids. Ricinoleic acid comprises 80–90% wt. of fatty acids in castor oil (Ricinus communis). In this study, the thermo-oxidative stability and tribological behavior of bio-based lubricant samples synthesized from castor oil using isoamyl alcohol were evaluated. Initially, the compositional and physicochemical properties of the obtained samples were assessed using 1H NMR, FTIR, and ASTM methods. Oxidative stability of the samples was evaluated using Rancimat method at 110 °C under air flow. The final biolubricant sample (BL2), obtained after esterification, epoxidation, and oxirane rings opening reactions, presented an oxidation stability time (OST) of 14.3 h. The thermal stability was also evaluated by thermogravimetry (TG) from the mass variations under inert and oxidative atmosphere. BL2 showed higher thermal stability compared to the other samples, demonstrating higher decomposition temperatures in both inert (339.04 °C) and oxidative (338.47 °C) atmospheres, for a mass loss of 50%. The tribological properties of the samples were evaluated using a four-ball tribometer configuration. The BL1 and BL2 samples exhibited lower friction coefficients than the mineral oil sample (MOS) by 21.5% and 43.1%, respectively. Regarding wear, the observed wear scar diameter (WSD) was also lower in BL1 and BL2 compared to MOS by 5.2% and 40.4%, respectively. The results of the tribological evaluation suggest that both samples obtained in this study have promising potential for applications in lubricating machines and mechanical systems.

Polydimethylsiloxane with hydroxy groups was functionalized to form functionalized polydimethylsiloxane, which subsequently underwent an addition reaction with isophorone diisocyanate to form the prepolymer. Next, 3-aminopropyltriethoxysilane (APTS) reacted with 3-glycidoxypropyltrimethoxysilane (GPTS) to produce bridged polysilsesquioxanes, and the sol–gel technology was employed to form hyperbranched polysiloxane nanoparticles with hydroxy groups, which was used as the additive. The hyperbranched polysiloxane and the prepolymer containing NCO functional groups then underwent an addition reaction to produce the hybrid materials. Fourier-transform infrared spectroscopy and 29Si nuclear magnetic resonance were used to characterize the structure of the polyurethane hybrid. Regarding thermal stability, after the hyperbranched polysiloxane nanoparticles was introduced, the integral procedural decomposition temperature increased from 348 ºC for polyurethane matrix to 859 ºC for the hybrid material. The results revealed that the thermal stability of the hybrid material substantially increased by approximately 247%.

Trace metals are essential elements that play key roles in a number of biochemical processes governing human visual physiology in health and disease. Several trace metals, such as zinc, have been shown to play important roles in the visual phototransduction process. In spite of this, there has been little research conducted on the direct effect of trace metal elements on the visual pho-toreceptor rhodopsin. In the current study, we have determined the effect of several metal ions, such as iron, copper, chromium, manganese, and nickel on the conformational stability of rho-dopsin. To this aim, we analyzed, by means of UV-visible and fluorescence spectroscopic methods, the effects of these trace elements on the thermal stability of dark rhodopsin, the stability of its active Metarhodopsin II conformation, and its chromophore regeneration. Our results show that copper prevented rhodopsin regeneration and slowed down the retinal release process after il-lumination. In turn, Fe3+, but not Fe2+, increased the thermal stability of the dark inactive con-formation of rhodopsin, whereas copper ions markedly decreased it. These findings stress the important role of trace metals in retinal physiology at the photoreceptor level, and may be useful for the development of novel therapeutic strategies to treat retinal disease.

This work studied sorption regularities and assessed thermal stability and resistance to microbial degradation of humic acid as a result of 3 sorption cycles on bentonite clay, kaolinite, and muscovite using TGA/DSC, XRD, hydrophobic chromatography, light and electron microscopy, etc. The experiment revealed that kaolinite sorbed more humic acids (HAs) in terms of unit surface area (1.03 × 10-3 C, g/m2) compared to bentonite (0.35 × 10-3 C, g/m 10-3 g/m2). Sorption at pH 4.5 was accompanied by HA fractionation in amphiphilicity and chemical composition. HA was sorbed mainly due to hydrophobic components on the surface of all sorbents. HA was not intercalated into the interlayer spaces of montmorillonite during sorption. Sorption due to hydrophilic interactions was mostly performed on muscovite and bentonite than on kaolinite. Sorption was followed by a change in the chemical composition of HA and decreased C/N compared to free HA, indicating selective sorption of nitrogen-containing compounds which is most characteristic of muscovite. Only a relatively thermolabile HA fraction was adsorbed on all minerals while its thermal stability increased compared to that before the experiment. Thermal stability and ratio of the Exo2/Exo1 peak areas on the DSC curves of sorbed HA increased with each subsequent sorption cycle. Thermal stability and resistance to microbial oxidation of sorbed HA showed the following relationship: the higher the thermal stability, the less available is sorbed HA for utilization by microorganisms.

Black poplar (Populus nigra L.) was thermally modified in nitrogen atmosphere. Treatment in nitrogen atmosphere can improve the dimensional stability of black poplar. The effects of the modification process on poplar wood were evaluated for temperatures: 160 °C, 190 °C, and 220 °C applied for 2 h; and 160 °C and 190 °C for 6 h. The percentual impact of temperature and time of modification on the properties of modified wood was analysed. The study permitted to identify correlations between the chemical composition and selected physical properties of thermally modified poplar wood. The dimensional stability of poplar wood improves after thermal modification in nitrogen. The higher the temperature of modification, the lower the equilibrium moisture content (EMC) of black poplar. At the temperature of 220 °C, EMC was two times lower than the EMC of non-modified black poplar. It is also possible to reduce the dimensional changes of wood two-fold (at the modification temperature of 220 °C), both in radial and tangential directions, independently of the acclimatisation conditions (from 34% to 98% RH). Similar correlations have been found for wood that has been soaked in water. Higher modification temperatures and longer processing times contributed to a lower swelling anisotropy (SA).

In this study, a parameter of volume stability was proposed for the first time to design polymorph zirconia ceramics used for special components. A series of heterogeneous polymorph zirconia ceramics with various amounts of monoclinic (M) phase were fabricated by two-step sintering. Samples with about 27%, 31%, and 51% M phase content were selected to study the properties. The thermal shock durability was found to be associated with thermal expansion behavior and noncritical micro cracks, which both based on M phase initial content. In good agreement with experimental results, the correlation of normalized K versus M phase initial content was established. It could provide a repeatable reference to prepare special zirconia components without loss of density.

Light-colored and transparent polyimide (PI) films with good high-temperature dimensional stability are highly desired for advanced optoelectronic applications. However, in practice, the simultaneous achievement of good optical and thermal properties in one PI film is usually difficult due to the inter-conflicting molecular design for the polymers. In the present work, a series of PI-SiO2 nanocomposite films (ABTFCPI) were developed based on the PI matrix derived from hydrogenated pyromellitic anhydride (HPMDA) and an aromatic diamine containing benzanilide and trifluoromethyl substituents in the structure, 2,2'-bis(trifluoromethyl)-4,4'-bis[4-(4-aminobenzamide)]biphenyl (ABTFMB). The inorganic SiO2 fillers were incorporated into the nanocomposite films with the form of colloidal nanoparticles dispersed in the good solvent of N,N-dimethylacetamide (DMAc) for the PI matrix. The derived ABTFCPI nanocomposite films showed good film-forming ability, flexible and tough nature, good optical transparency, and good thermal properties with the loading amounts of SiO2 up to 30 wt% in the system. The ABTFCPI-30 film with the SiO2 content of 30 wt% in the film showed the optical transmittance of 79.6% at the wavelength of 400 nm (T400) with a thickness of 25 μm, the yellow index (b*) of 2.15, and the 5% weight loss temperatures (T5%) of 491 oC, which are all comparable to those the pristine ABTFCPI-0 matrix without filler (T400=81.8%; b*=1.77; T5%=492 oC). Meanwhile, the ABTFCPI-30 film exhibited obviously enhanced high-temperature dimensional stability with the linear coefficients of thermal expansion (CTE) of 25.4×10-6/K in the temperature range of 50 to 250 oC, which is much lower than that of the AMTFCPI-0 film (CTE=32.7×10-6/K).

Ni-rich layered cathodes are regarded as a potential candidate for high energy-density lithium-ion batteries, but their high sensitivity to air during storage and poor thermal stability are a vital challenge for large-scale applications. In this paper, an effective solid-solution strategy was proposed to improve the surface and structural stability of Ni-rich layered cathodes by introducing Li2MnO3. The structural analysis results indicate that the formation of Li2CO3 inert layers on Ni-rich layered cathodes during storage in air is responsible for the increased electrode interfacial impedance, thereby resulting in the severe deterioration of electrochemical performance. The introduction of Li2MnO3 can reduce the surface reactivity of Ni-rich cathode materials, playing a certain suppression effect on the formation of surface Li2CO3 layer and the deterioration of electrochemical performances. Additionally, the thermal analysis results show that the heat release of Ni-rich cathodes strongly depends on the charge of states, and Li2MnO3 can suppress oxygen release and significantly improves the thermal stability of Ni-rich layered cathodes. This work provide a method to improve the storage performance and thermal stability of Ni-rich cathode materials.

Modification of Scots pine sapwood (Pinus sylvestris L.) with heterocyclic compounds, imidazole and succinimide, was investigated. Pressure-impregnation with aqueous solutions containing imidazole, imidazole + citric acid, succinimide, succinimide + citric acid, and citric acid + sorbitol (CIOL®) at 5%, 10%, and 15% solid content was followed by oven-curing at 220 °C for 1 hour. Mass changes during treatment steps, bending properties, and anti-swelling efficiency (ASE) were examined. Results indicate that solid concentrations within the range of 5% to 10% were optimal. Results seem to show there are two differing mechanisms in the modification of imidazole and succinimide, respectively. Mass loss due to the heat treatment was highest in imidazole-treated specimens, whereas it remained low and concentration-independent in succinimide-treated specimens. ASE after three cycles reached 31% for imidazole-treated specimens and improved to 38% with the addition of citric acid. For succinimide, ASE increased from 17% to 41%. Bending properties generally showed improvement, except for succinimide + citric acid and CIOL®, which displayed a reduced modulus of rupture. Chemical analyses are warranted to fully understand the reaction mechanisms of the treatments. Imidazole treatment's positive effects are suggested to stem from a thermal reaction between the chemical and wood, indicated by substantial mass loss during leaching and specimen darkening. Succinimide and citric acid might exhibit polymerization with each other and wood components, akin to the CIOL® process. Further research should delve into reaction mechanisms and the impact of imidazole and succinimide on biological durability.

In current work, we illustrate the effect of adding small amount of Carbon to very common Co2MnSi Heusler alloy based-glass coated microwires. A significant change in the magnetic and structure structural properties has observed for the new alloy Co2MnSiC compared to the Co2MnSi alloy. The magneto-structural investigations have performed to clarify the main phys-ical parameters i.e., structural & magnetic at a wide range of measuring temperature. The XRD analysis illustrated the well-defined crystalline structure with average grain size (Dg = 29.16 nm) and a uniform cubic structure with A2-type compared to the mixed L21 and B2 cubic structures for Co2MnSi-based glass coated microwires. The magnetic behaviour has investigated at a tem-perature range (5 to 300 K) and an external applied magnetic field (50 Oe to 20 kOe). The adding of small amount of Carbon to the Co2MnSi matrix enhance the magnetic thermal stability, where the thermomagnetic behaviour of Co2MnSiC glass-coated microwires show a perfect stable be-haviour for a temperature range from 300 K to 5 k, the differences between the coercivity value is only 0.3 Oe compared to 4 Oe for Co2MnSi-sample. In addition, M-H loops measured at tempera-ture below 50 K show unsaturated loops; meanwhile the Co2MnSi loops shows a strong antifer-romagnetic coupling for the loops measured below 50 K. By studying the field cooling (FC) and field heating (FH) magnetizations curves at a wide range of external applied magnetic field we detected a critical magnetic field (H = 1 kOe) where FC and FH curves have a stable magnetic behavior for Co2MnSiC sample, such stability does not find in Co2MnSi sample. We proposed a phenomenal expression to estimate the magnetization thermal stability, ΔM (%), of FC and FH magnetization curves and the maximum value is detected at the critical magnetic field where ΔM (%) ≈ 98 %. The promising magnetic stability of Co2MnSiC glass-coated microwires with tem-perature is due to the changing of the microstructure induced by adding Carbon, as the A2-type structure show a unique stability by variation the temperature and the external magnetic field. In addition, a unique internal mechanical stress, which induced during the fabrication process and plays on controlling magnetic behavior with temperature and external magnetic field. The ob-tained results make Co2MnSiC promising candidate for magnetic sensing devices based Heusler glass-coated microwires.

In this paper, we investigate the stabilization of a one-dimensional thermoelastic laminated beam with structural damping, coupled to a heat equation modeling an expectedly dissipative effect through heat conduction governed by Gurtin-Pipkin thermal law. Under some assumptions on the relaxation function g, we establish the well-posedness for the problem. Furthermore, we prove the exponential stability and lack of exponential stability for the problem. To achieve our goals, we make use of the semigroup method, the perturbed energy method and Gearhart-Herbst-Prüss-Huang theorem.

The manuscript reported the synthesis of Al2O3 nano-coating onto quartz fiber by plasma electrolysis spray for enhanced thermal conductivity and stability. The nano- and micro-sized clusters were partially observed on the coating, while most coating was relatively smooth. It was suggested that the formation of a ceramic coating was followed as the nucleation-growth raw, that is, the formation of the coating clusters was dependent on the fast grow-up partially, implying the inhomogeneous energy distribution in the electrolysis plasma. The deposition of the Al2O3 coating increased the annealing tensile strength from 19.2 MPa to 58.1 MPa. The thermal conductivity of the coated quartz fiber was measured to be 1.17 W m-1 K-1, increased by ~45% compared to the bare fiber. The formation mechanism of the Al2O3 coating was preliminarily discussed. We believe that the thermally conductive quartz fiber with high thermal stability by plasma electrolysis spray will find a wide range of applications in industries.

Colloidal quantum dots (CQDs) are valuable for their potential applications in optoelectronic devices. However, they are susceptible to thermal degradation during processing and while in use. Mitigating thermally induced sintering, which leads to absorption spectrum broadening and undesirable changes to thin film electrical properties, is necessary for the reliable design and manufacture of CQD-based optoelectronics. Here, low temperature metal-oxide atomic layer deposition (ALD) was investigated as a method for mitigating sintering while preserving the optoelectronic properties of mercury telluride (HgTe) CQD films. ALD-coated films are subjected to temperatures up to 160oC for up to 5 hours and alumina (Al2O3) is found to be most effective at preserving the optical properties, demonstrating the feasibility of metal-oxide infilling to protect against sintering. HgTe CQD film electrical properties were investigated before and after alumina ALD in-filling, which was found to increase the p-type doping and hole mobility of the films. The magnitude of these effects depended on the conditions used to prepare the HgTe CQDs. With further investigation into the interaction effects of CQD and ALD process factors, these results may be used to guide the design of CQD-ALD materials for their practical integration into useful optoelectronic devices.

This study investigates the long-term stability of the Suomi National Polar-orbiting Partnership (S-NPP) Visible Infrared Imaging Radiometer Suite (VIIRS) moderate-resolution Thermal Emissive Bands (M TEBs; M12 – M16) covering a period from February 2012 to August 2020. It also assesses inter-sensor consistency of the VIIRS M TEBs among three satellites-S-NPP, NOAA-20, and NOAA-21 over eight months spanning from March 18 to November 30, 2023. The field of interesting is limited to the ocean surface between 60°S and 60°N, specifically under clear-sky conditions. Taking radiative transfer modeling (RTM) as the transfer reference, we employed the Community Radiative Transfer Model (CRTM) to simulate VIIRS TEB brightness temperature (BTs), incorporating European Centre for Medium-range Weather Forecasts (ECMWF) reanalysis data as inputs. Our results reveal two key findings. Firstly, the reprocessed S-NPP VIIRS TEBs exhibit a robust long-term stability, as demonstrated through analyses of the observation minus background BT differences (O-B ∆BTs) between VIIRS measurements (O) and CRTM simulations (B). The drifts of the O-B BT differences are consistently less than 0.105 K/Decade across all S-NPP VIIRS M TEB bands. Notably, observations from VIIRS M14 and M16 stand out with drifts well within 0.04 K/Decade, reinforcing their exceptional reliability for climate change studies. Secondly, excellent inter-sensor consistency among these three VIIRS instruments is confirmed through the double-difference analysis method (O-O). This method relies on the O-B BT differences obtained from daily data. The mean inter-VIIRS O-O BT differences remain within 0.08 K for all M TEBs, except for M13. Even in the case of M13, the O-O BT differences between NOAA-21 and NOAA-20/S-NPP have values of 0.312 K and 0.234 K, respectively, which are comparable to the 0.2 K difference between some TEBs among VIIRS and MODIS. These disparities are primarily attributed to the significant differences in the Spectral Response Function (SRF) of NOAA-21 compared to NOAA-20 and S-NPP. Our study confirms the RTM-based TEB quality evaluation method’s versatility and effectiveness in assessing long-term sensor stability and inter-sensor consistency. The double-difference approach effectively mitigates uncertainties and biases inherent to CRTM simulations, establishing itself a robust mechanism for assessing inter-sensor consistency. In addition, we’ve observed that, except for M13, M12 always exhibits larger spatial variations of O-O BT differences with greater uncertainties compared to the other M TEBs. The influence of solar contribution through sea surface reflection on the Top of Atmosphere (TOA) radiance measurements during daytime in M12 should not be underestimated.

Almond is worldwide consumed and renowned as a valuable healthy food. In spite of this, it is also a potent source of allergenic proteins able to trigger several mild to life-threatening immunoreactions. Food processing proved to alter biochemical characteristics of proteins, thus affecting the respective allergenicity. In this paper we investigated the effect of autoclaving, preceded or not by a hydration step, on the biochemical and immunological properties of almond proteins. Any variation in the stability and immunoreactivity of almond proteins extracted from the treated materials, were evaluated by total protein quantification, ELISA assay and protein profiling by electrophoresis-based separation (SDS-PAGE). The autoclaving alone was found to weakly affect almond proteins stability, despite what observed for the combination of hydration and autoclaving, which resulted in a loss of approximately 70% of total protein content compared to untreated sample, and in a final negligible immunoreactivity, as well. The final SDS-PAGE protein pattern recorded for almonds hydrated and autoclaved disclosed significant changes. In addition, the same samples were further submitted to in vitro simulated gastro-duodenal (GI) digestion to evaluate potential changes induced by these processing on allergens digestibility. Digestion products were identified by HPLC-HRMS/MS analysis followed by software-based data mining, and complementary information were provided by analyzing the proteolytic fragments lower that 6 kDa in size. The autoclave based treatment was found not to alter the allergens digestibility, whereas an increased susceptibility to proteolytic action of digestive enzymes was observed in almonds subjected to the combination of prehydration and autoclaving. Finally, the residual immunoreactivity of the GI resistant peptides was investigated in-silico by bioinformatic tools, confirming that by following both approaches, no epitopes survived the almond digestion, thus demonstrating the potential effectiveness of these treatments to reduce almond allergenicity.

Modelling water vapour flow, heat transfer and porosity in porous adsorbent is somewhat challenging simulation problem. Primary macroscopic water vapour flow models, such as Darcy's law, fail to predict the pressure drop entirely correctly for the reason that many of flow parameters not considered because of the simplifications that remain made for the multi-scale structure of the porous adsorbents. For one to develop a good physical understanding of such water vapour flows and the accuracy of existing 3D simulation models, there is a need for some accurate 3D geometry to be studied. This present work describes two-phase water vapour flow and adsorption/ desorption performed on porous adsorbent by a Dynamic vapour sorption (DVS). The CFD simulation results are associated with experiments results. It is decided that for such complex porous adsorbent CFD simulation problems the use of COMSOL Multiphysics and SolidWorks flow simulation will be utilised.

This study investigates the impact of vertical greenery systems (VGS) applied to heavyweight walls on indoor thermal conditions in a building module situated in the Mediterranean climate of Catania, Italy. Using dynamic simulations in TRNSYS, the research compares the thermal behavior of walls constructed from hollow clay blocks (Poroton) and lava stone blocks with a lightweight wall setup already in place at the University of Catania. The primary focus is on evaluating the VGS’s effect on reducing peak inner surface temperatures and moderating heat flux fluctuations entering the building. The findings indicate that adding a vertical greenery layer to heavyweight walls can decrease the peak inner surface temperature by up to 1.0°C compared to the same wall without vegetation. However, the greenery’s impact on mitigating heat flux fluctuations is less pronounced than in the case of the lightweight wall. This research underscores the potential of green facades in enhancing indoor thermal comfort in regions with climates similar to the Mediterranean, providing valuable insights for sustainable building design and urban planning.

This research is a preliminary phase of a general effort to develop a generic-data transferring capability via human haptic thermal sensation (generic-data refers to a coded language like Morse or Braille). For the capability to be effective, it must include a large variety of short recognizable cues. Hence, we propose the concept of cues based on sequences of thermal pulses, i.e., combinations of warm and cool pulses with several levels of intensity. The objective of this study was to determine the feasibility of basing a generic-data-transfer capability on thermal cues composed of sequences of short pulses. The research included defining the basic characteristics of the stimuli parameters and developing practical methods for generating and measuring them. Several sequences were designed in light of the relevant data known to date, and tests were conducted. The thermal cues presented to the participants were sensed and recognized by touch. The results indicate high feasibility for a capability that is applicable in various scenarios. In addition, the low impact on human skin temperature due to short stimuli duration represents an inherent advantage for later implementation. This report presents promising findings and offers insights for further investigation.

In the quest for more efficient solar thermal systems, accurately determining the thermal emittance of low-emissive materials is crucial in determining the power losses. This paper describes the calorimetric method designed to precisely measure the thermal emittance of Selective Solar Absorbers (SSAs) to be used in High Vacuum Flat Plate Collectors (HVFPCs). The method's capability is demonstrated through the successful correction of thermal emittance values for copper samples of varying sizes, including dimensions down to 49 cm². Results highlight the method's potential to significantly reduce measurement errors associated with small-size and/or low-emittance samples, providing a path forward to improve the design and efficiency of SSAs. This research marks a significant step in advancing solar thermal technology by enabling emittance measurements with a precision better than 0.003, which is essential for the development of high-performance solar thermal absorbers. The method has also been applied to correct the thermal emittance value of SSA measured in previous measurement campaigns, and it allows a better estimation of the SSA efficiency conversion curve.

In this paper, the experimental results of the thermal sub-system of a reliable and cost-effective polygeneration solar system are presented. This polygeneration system produces heating, cooling and electricity from solar energy, which are used in an existing test-building. Heat is generated in four evacuated tube solar collectors (ETC). The heat may be used for space cooling, through a variable geometry ejector (VGE) heat pump. In order to reduce the mismatches between generation and consumption, two thermal storage tanks were added. The performance of a new thermal storage, with 400 l, able to storage both sensible and latent heat, was tested. Heating performances of the test-building were assessed. Ejector cycle tests were also performed.

Based on PVDF (piezoelectric sensing techniques), this paper attempts to study the propagation law of shock waves in brittle materials during the process of three-wavelength laser irradiation of polysilicon, and discusses the formation mechanism of thermal shock failure. The experimental results show that the vapor pressure effect and the plasma pressure effect in the process of pulsed laser irradiation lead to the splashing of high temperature and high density melt. With the decrease of the laser wavelength, the laser breakdown threshold decreases and the shock wave is weakened. Because of pressure effect of the laser shock, the brittle fracture zone is at the edge of the irradiated area. The surface tension gradient and surface shear wave caused by the surface wave are the result of coherent coupling between optical and thermodynamics. The average propagation velocity of laser shock wave in polysilicon is 8.47×103m/s, and the experiment has reached the conclusion that the laser shock wave pressure peak exponentially distributes attenuation in the polysilicon.

The cell case temperature versus time profiles of a multistage fast charging technique (4C-1C-CV)/fast discharge (4C) in a 2.3 Ah cylindrical lithium-ion cell are analyzed using a 1D thermal model. Heat generation is dominated by the irreversible component associated to cell overpotential, although evidences of the reversible component are also observed, associated to the heat related to entropy from the electrode reactions. The final charging stages (i.e., 1C-CV) significantly reduce heat generation and cell temperature during charge, resulting in a thermally safe charging protocol. Cell heat capacity was determined from cell specific heats and cell materials thickness. The 1D model adjustment of the experimental data during the 2 min. resting period between discharge and charge allowed us to calculate both the time constant of the relaxation process and the cell thermal resistance. The obtained values of these thermal parameters used in the proposed model are almost equal to those found in the literature for the same cell model, which suggests that the proposed model is suitable for its implementation in thermal management systems.

Amphiphilic block copolymers of N-vinyl pyrrolidone (NVP) and various vinyl esters (VEs), PNVP-b-PVEs, namely vinyl butyrate (VBu), vinyl decanoate (VDc) and vinyl stearate (VSt) were synthesized by RAFT polymerization techniques. The sequential addition of monomers methodology was employed starting from the polymerization of NVP followed by the polymerization of the VEs monomer. The reaction was conducted at 80oC in dioxane solutions using AIBN as initiator and O-ethyl S-(phthalimidylmethyl) xanthate as the CTA. The block copolymers were characterized by Size Exclusion Chromatography (SEC) and NMR spectroscopy. The thermal transitions of the copolymers were studied by Differential Scanning Calorimetry (DSC), whereas their thermal stability via Thermogravimetric Analysis (TGA) and Differential Thermogravimetry (DTG).

Anaerobic digestion is a biological process that transforms high-strength organic effluents into biogas with multiple benefits. However, concurrent with organics' biological transformation, a liquid phase with a high solid content is also derived from this process. Valorizing this fraction is not an easy task if an agronomic application cannot be considered as a suitable option. The thermal valorization of this fraction allows for energy extraction, but also gives rise to additional capital investment and increases the energy demand of the global process. In addition, the thermal treatment of digestate has to deal with a mineralized material. The changes in organic matter due to anaerobic stabilization were studied in the present manuscript, by evaluating the thermal behavior of samples, activation energy and organic transformation using FTIR spectroscopy. Digested samples of a mixture composed of manure and glycerin (5% v/v) were studied. The stabilization caused a dramatic decrease in aliphatic compounds, greatly increasing the mineral content of the sample. Thermal valorization of digestates must consider the lower energy content and more complex structure of these materials, with higher content of lignin and protein-type compounds.

To expand the application scope and increase the demand for non-crimp fabrics (NCFs) as a lightweight vehicle material, the delamination and thermal strain in NCF composites must be restricted. Accordingly, to simultaneously improve the interfacial bonding and thermal stability of the NCF composites, in this study the epoxy resin, in which SiO2 nanoparticles was modified by a silane coupling agent, were infused to the stacked NCFs and between the layers of NCFs through the vacuum-assisted resin infusion molding (VARIM) process.

The examination of ampacity in overhead transmission lines offers a comprehensive overview, covering its definition, thermal evaluation methodologies, standards, practical applications, and the potential of high-temperature low-sag (HTLS) conductors. By navigating through static and dynamic approaches to thermal evaluation and detailing methodologies prescribed by international standards like those from CIGRE and IEEE, this study provides a solid understanding of how ampacity is determined and optimized. Furthermore, the exploration of HTLS conductors introduces a forward-looking perspective on enhancing transmission capacity whereas mitigating the need for extensive infrastructure modifications. Through an analysis of regional considerations and preferences using Slovak standards and CIGRE Technical Brochure 601, insights are provided on how environmental factors influence transmission line performance. The analysis of the transition from traditional ACSR to advanced ACCC (Aluminium Conductor Composite Core) conductors demonstrates the tangible benefits of adopting advanced conductor technologies in real-world scenarios.

This paper is the second part of a two-part report studying the responses of a typical point-contact elastohydrodynamic lubrication (EHL) problem to multiscale roughness that is mimicked by artificially generated waviness with different amplitudes, frequencies, and directions. The previous Part I paper (doi:10.3390/lubricants10120368) focuses on the full film regime, while the current paper focuses on the partial film regime. The amplitudes and frequencies are related to the feature geometry of smooth EHL problems. Generated waviness is input to a transient thermal EHL model. The simulation is conducted 1,600 times for different waviness parameters, loads, and speeds. Eight performance parameters are extracted: the asperity contact ratio, minimum film thickness, maximum pressure, central point film thickness, central point pressure, mean film thickness, coefficient of friction (COF), and the maximum temperature rise. The ratios of the first seven parameters with and without waviness and the asperity contact ratio values are plotted on the frequency–amplitude coordinate plane as contour maps. The influences of the amplitude, frequency, wave direction, load, and speed on the eight performance parameters are analyzed and summarized. The simulated data and plotted contour maps are provided to the readers in the Supplementary Material.

No matter where we reside, the issue of greenhouse gas emissions impacts us all. Their influence has a disastrous effect on the earth's climate, producing global warming and many other irreversible environmental impacts, even though it is occasionally invisible to the independent eye. Phase change materials (PCMs) can store and release heat when it is abundant during the day (e.g., from solar radiation), for use at night, or on chilly days when the building needs to be heated. As a consequence, buildings use less energy to heat and cool, which lowers greenhouse gas emissions. Consequently, research on thermally active medium-density fiberboard (MDF) with PCMs is presented in this work. MDF is useful for interior design and furniture manufacturing. The boards were created using pine (Pinus sylvestris L.) and spruce (Picea abies L.) fibers, urea-formaldehyde resin, and PCM powder, with a phase transition temperature of 22 oC, density of 785 kg m−3, the latent heat capacity of 160 kJ kg−1, the volumetric heat capacity of 126 MJ m−3, the specific heat capacity of 2.2 kJ kgK−1, the thermal conductivity of 0.18 W mK−1, and a maximum operating temperature of 200 °C. Five variants of MDF with PCM additive were developed: 0%, 5%, 10%, 30%, and 50%. According to the study, scores at the MOR, MOE, IB, and Screw Withdrawal Resistance (SWR) tests decreased when PCM content was added. However, the results of the thickness swelling and water absorption tests indicate that the PCM particles do not exhibit a substantial capacity to absorb water, retaining the dimensional stability of the MDF boards. The panel's thermal characteristics improved with increasing PCM concentration, according to the data. The density profiles of all the variations under consideration had a somewhat U-shaped appearance; however, the version with a 50% PCM content had a flatter form and no obvious layer compaction on the panel surface. Therefore, certain of the mechanical and physical characteristics of the manufactured panels can be enhanced by a well-chosen PCM addition.

The Predicted Mean Vote (PMV) and the Predicted Percentage of Dissatisfied (PPD) indices are used to assess the indoor environment in terms of human thermal comfort-discomfort. In this study, an experimental combined objective and subjective investigation of thermal comfort perception has been performed in students between 16-18 years old, in a non-air-conditioned school building. The objective approach included instrumentation measurements and data processing according to ISO 7730, whereas, the subjective one was based on answers collection following ISO 10551. The study is mainly devoted to the verification of Fanger’s approach in a building, in free running conditions, under a mild (moderate) climate.The comparison between instrumentation data and questionnaire results presented an underestimation of the mean vote, predicting a cooler sensation than the actual one.

This study investigates the microstructural evolution and mechanical properties of high-nickel shipbuilding steel during thermal processing using High Temperature Confocal Laser Scanning Microscopy (HTCLSM). The in-situ observation of the heating and holding processes reveals critical insights into phase transformations, grain growth behavior, and the formation of precipitates. The experimental results demonstrate that austenitization begins at approximately 700°C, with significant grain boundary nucleation. At 900°C, the formation of black precipitates was observed, and their persistence up to temperatures exceeding 1000°C was confirmed. Scanning Electron Microscopy (SEM) and Energy Dispersive Spectroscopy (EDS) analyses identified these precipitates as chromium carbides (Cr7C3), which significantly contribute to the material's strength. The comprehensive analysis using Transmission Electron Microscopy (TEM) confirmed the presence and distribution of Cr7C3 within the grains and along grain boundaries. These findings provide a deeper understanding of the microstructural dynamics in high-nickel steels, guiding the optimization of heat treatment processes to enhance mechanical properties for maritime applications.

Graphene foam prepared by chemical vapor deposition method is a promising thermal interfacial material. However, the thermal properties of graphene foam highly depend on the experimental fabrication conditions during the chemical vapor deposition process. Aiming to reveal how to prepare the appropriate graphene foam for the various thermal management scenarios, the influence of experimental conditions on thermal properties of graphene foam is investigated. Furthermore, the contribution of thermal conductivity and thermal radiation to the effective thermal coefficient of graphene foam is carried out for comparison. Research results show that, the porosity and the cross-section shape of struts of growth template are two critical factors to affect the thermal transport of graphene foam, especially with the increase of temperature. In addition, the deposition time of graphene determines the wall thickness and affects the thermal conductivity directly. The thermal radiation contributes more than thermal conductivity when the temperature climbs continuously. Comparatively, the effective thermal coefficient of graphene foam composite with high porosity and circular shape struts is much superior to others at high temperature. The research findings can provide important guidance for the graphene foam fabrication and its applications in the field of thermal management.

This study investigates the land surface temperature (LST) distribution from thermal infrared data for analyzing the characteristics of surface coverage using the Vegetation-Impervious-Soil (VIS) approach. A set of ten images, obtained from Landsat-5 Thematic Mapper, between 2001 and 2010, were used to study the urban environmental conditions of 47 neighborhoods of Porto Alegre city, Brazil. Porto Alegre has had the smallest population growth rate of all 27 state capitals in the last two decades in Brazil, with an increase of 11.55% in inhabitants from 1,263 million in 1991 to 1,409 million in 2010. We applied the environmental Kuznets curve (EKC) theory in order to test the influence of the economically-related scenario on the spatial nature of social-environmental arrangement of the city at neighborhood scale. Our results suggest that the economically-related scenario exerts a non-negligible influence on the physically driven characteristics of the urban environmental conditions as predicted by EKC theory. The linear inverse correlation R2 between household income (HI) and LST is 0.36 and has shown to be comparable to all other studied variables. Future research may investigate the relation between other economically-related indicators to specific land surface characteristics.

The growing interest in heat-conducting nanofluids requires highly sensitive methods for analyzing thermal properties. Thermal-lens spectrometry, despite its advantages over classical methods, does not have a general approach to measuring and interpreting results for dispersed systems. In this paper, by the example of nanofluids of silicon oxide in water in a wide range of concentrations and sizes, the selection of measurement parameters for transient and steady-state thermal lensing is justified, and the interpretation of the results of thermal diffusivity measurements is substantiated. The features of measurements of thermal diffusivity by thermal lens spectrometry under stationary state for dispersed systems are considered. Using this approach, it is possible to detect and distinguish thermal effects with high accuracy. For dispersions of silicon oxide, with increasing concentration, the thermal diffusivity passes through a minimum. Silicon oxide dispersions can be used both as a coolant or as a heat-removing liquid by selecting the particle size and concentration.

In order to solve the problem of large eddy current loss and high temperature rise caused by large amount of permanent magnet, a new type of combined magnetic pole permanent magnet motor is proposed in this paper. The sinusoidal distribution subdomain model of non-uniform air gap rotor is established by using Laplace equation, and the analytical expression of eddy current loss of rotor in uniform air-gap and non-uniform air-gap is derived. The effect of rotor eccentricity on eddy current loss is obtained. According to the characteristics of distributed winding of non-uniform air gap combined pole permanent magnet motor, equivalent treatment is performed to obtain the equivalent thermal conductivity, so as to establish equivalent thermal network model of motor, calculate the temperature value of each component of the motor, and verify the correctness of the thermal network model through the method of magnetothermal bidirectional coupling. Finally, an experimental platform is set up to carry out temperature rise experiments on the two prototypes respectively. Experimental results show that the non-uniform air-gap rotor structure can effectively reduce the rotor eddy current loss and motor temperature rise, and also verify the accuracy of the analytical model calculation results.

Synergistic control of emissions of air pollutants and CO2 is critical to the dual challenges of air quality improvement and climate change in China. Based on the emission inventories of thermal power units in Beijing, Tianjin, and Hebei, this study analyzes the CO2 and NOX emission characteristics of these units, identifies and quantifies the synergistic drivers affecting these emission trends. Inventory data show that between 2010 and 2020, NOX emissions were reduced by 86.1%, while CO2 emissions were reduced by only 29.8%. Although significant progress has been made in reducing NOX emissions through measures such as end-of-pipe treatment, controlling CO2 emissions remains a difficult task. The index decomposition analysis reveals that economic growth is the main driver of CO2 and NOx emission growth, energy intensity reduction is the main driver of CO2 emission reduction, and end-of-pipe treatment is the main driver of NOX emission reduction. Currently, coal occupies about 87% of the energy consumption of thermal power units in the Beijing-Tianjin-Hebei, and remains the main type of energy for synergistic emissions, and the potential for emission reduction in the energy structure remains huge. For NOX emissions, it is expected that 90% of the reduction potential can be achieved through energy restructuring and end-of-pipe treatment. In conclusion, the high-precision unit-by-unit emission study confirms the effectiveness of the control policy for thermal power units in the region and provides some scientific reference for future policy formulation.

Compact solar-powered plasma water generator: enhanced on-site aged seed germination with the corona dielectric barrier discharger

Loop-Mediated Isothermal Amplification (LAMP) is a widely used technique for nucleic acid amplification due to its high specificity, sensitivity, and rapid results. Advances in microfluidic lab-on-chip (LOC) technology have enabled the integration of LAMP into miniaturized devices, known as μ-LAMP, which require precise thermal control for optimal DNA amplification. This paper introduces a novel thermal bed design using PCB copper traces and FR−4 dielectric materials, providing a reliable, modular, and repairable heating platform. We present the design, fabrication, and control mechanisms of the thermal bed, demonstrating its ability to maintain accurate temperatures essential for μ-LAMP applications. The thermal bed’s performance is validated through finite element method (FEM) simulations, confirming its effectiveness in diverse applications such as disease diagnostics, biological safety, and forensic analysis.

In this study, we evaluate the nonlinear dynamics of convection flow using the thermodynamic variational principle, focusing on scenarios where multiple external forces, such as a thermal gradient and rotational field, are applied to a shallow annular pool. We observed that with the increase in the thermal gradient, the flow changed from an axial flow to a rotational oscillatory flow with the wave amplitudes aligned. Further increasing the temperature difference led to a rotational oscillatory flow characterized by alternating wave generation and annihilation. Our analysis of the flow, considering heat fluxes orthogonal to the thermal gradient, allowed us to describe the flow state as a phase at equilibrium. The state transition of the flow was accompanied by a discontinuous jump in the heat flux, which occurred at the intersection of the entropy production curves.

Global climate change, particularly rising sea surface temperatures, profoundly impacts coral ecosystems, disrupting reproduction synchrony, symbiotic relationships with algae from the Symbiodiniceae family, and causing widespread bleaching and mortality among coral populations.  Oculina patagonica, a temperate scleractinian coral dominant in Mediterranean coastal waters, tolerates an annual temperature range of 10- 31°C. Moreover, in the past three decades, sea surface temperatures have rapidly risen in the Eastern Mediterranean Sea. O. patagonica offers insight into evolutionary adaptation to rapid environmental changes. This study investigated the effects of temperature changes on O. patagonica reproductive development, synchrony, and thermal sensitivity. Monthly monitoring of O. patagonica colonies for a year reveals no disruption in gonad development compared to previous studies, suggesting an unaffected sexual reproduction capacity. Thermal performance

The development of offshore wind farms requires robust bonding solutions that can withstand harsh marine conditions for the easy integration of secondary structures. This paper investigates the durability performance of two adhesives: Sikadur 30 adhesive and Loctite UK 1351 B25 for use in offshore wind environments. Tensile tests on adhesive samples and accelerated aging tests were carried out under a variety of temperature and environmental conditions, including both dry and wet conditions. The long-term effects of aging on adhesive integrity are investigated by simulating the operational life of offshore installations. The evolution of mechanical properties, studied under accelerated aging conditions, provides an important indication of the longevity of structures under normal conditions. The results show significant differences in performance be-tween the two adhesives, highlighting their suitability for specific operating parameters. It should also be noted that for both adhesives, their exposure to different environments (seawater, distilled water, humid climate) over a prolonged period has shown that i) Loctite adhesive has a slightly faster initial uptake than Sikadur adhesive, but the later reaches an asymptotic plateau with a lower maximum absorption rate than Loctite adhesive; and ii) a progressive deterioration in the tensile properties following an exponential function. Therefore, aging behavior results showed a clear correlation with Arrhenius' law, providing a predictive tool for the aging process. Thus, the aging process of the two adhesives follows Arrhenius kinetics.

Flap surgery is a common method used to cover defects following tumor ablation, trauma, or infection. However, insufficient vascularity in the transferred flap can lead to flap necrosis and failure. Proper postoperative monitoring is essential to prevent these complications. Recently, research has explored the use of infrared thermal imaging in plastic surgery, leading to its clinical application. This study investigates the use of a forward-looking infrared (FLIR) camera to monitor blood flow in flaps. In the study, 28 rats underwent reverse McFarlane flap surgery, and their flaps were analyzed using a FLIR thermal imaging camera seven days post-surgery. Additionally, thermal images of flaps were taken on postoperative days 0, 1, 2, 3, and 7 in 22 patients. The study focused on temperature differences between normal skin and the perforator compared to the average flap temperature. Results showed that the temperature difference was higher in the necrosis group and increased over time in cases of total necrosis. A lower perforator temperature compared to the flap's average indicated vascular compromise, potentially leading to flap failure. The FLIR camera, being contact-free and convenient, shows promise for understanding and inferring the clinical progression of flaps in postoperative monitoring.

The main goal was to investigate the ability of non-thermal plasma reactor with gliding arc discharge to remove the diesel exhaust particulates (DEPs). A conventional knifed-shaped LTP GA reactor was utilized. Three cases were studied: 140 L/min, 70 L/min and 14 L/min of air drawn through the reactor and diesel exhaust fumes were sampled continuously. They were assayed in terms of concentration and number particle size distribution. The higher the residence time’s, the higher the energy input that may be utilized for DEPs’ removal. Reactor’s performance definitely lowered the concentration of DEPs (250 - 580 nm) and altered their number size distribution. There was no effect on the number concentration, nor on the particle size distribution, of DEP particulates of 10 – 250 nm in size. The effectiveness of DEPs’ removal: Decreasing flow rate from 140 L/min to 70 L/min somehow altered the values. Achieving the airflow of 14 L/min led to a substantial improvement (even to a fourfold increase for 300 – 480 nm particles). Non-thermal plasma reactors with gliding arc discharge may be successfully adapted in the process of DEPs’ treatment. Their performance may be optimized by adjusting the airflow at the inlet of reactor to guarantee the longest aerosol residence times and the highest removal efficiency.

The thermal degradation behaviour of 10:90 and 90:10 blends of Polyethylene Terephthalate (PET) and petroleum coke has been investigated using mechanical alloying (milling) at 300 rpm and for periods up to 1-10 hours. Milled specimens were characterised using SEM and x-ray diffraction; their thermal degradation behaviour was investigated using thermo-gravimetric analyser (TGA) for temperatures up to 1200°C. Whereas PET specimens showed a tendency towards flattening out and increased surface area during collisions in ball mills, petroleum coke particles tended to break down into smaller particles. 10:90 and 90:10 blends of PET and coke showed significant microstructural evolution with increasing speeds and time including fracture, strain hardening and re-welding. X-ray diffraction results showed clear evidence for increasing amorphous component in petroleum coke without much influence on PET crystallinity. Thermo-gravimetric results showed a significant increase in the overall degradation and much higher weight losses associated with mechanical alloying. This study has shown that mechanical alloying could be used to modify the degradation behaviour of coke/plastic blends and corresponding yield during pyrolysis with implications for plastic waste management.

Background: Our previous study revealed that the addition of pentavalent cations, such as niobium (Nb), to zirconia stabilized with trivalent cations, such as yttrium (Y), increased fracture toughness. However, the coefficient of thermal expansion (CTE) and opacity also increased undesirably. Thus, a novel surface treatment is required to enhance fracture toughness without changing the CTE and the translucency. Methods: The surfaces of pre-sintered 3-mol% yttria-stabilized tetragonal zirconia polycrystal (3Y-TZP) and 4.2-mol% yttria-stabilized partially stabilized zirconia (4.2Y-PSZ) were treated with an Nb sol solution containing Nb2O5 nanoparticles. After drying and final sintering, a surface layer with high Nb content formed to a depth of approximately 1 mm. Results: Nb was equivalent to that of the bulk uniformly containing 1 mol% Nb2O5. The tetragonality of tetragonal zirconia near the surface increased with the addition of Nb, leading to improve fracture toughness in the surface layer and enhancing the fracture toughness of the entire specimen. However, the CTE and the translucency remained unchanged. Conclusions: The addition of pentavalent cations such as Nb, confined to the surface vicinity, improved fracture toughness without affecting the CTE and the translucency. By selectively adding Nb to the surface of weak parts of zirconia prosthesis, the overall strength can be improved, making it possible to produce highly reliable dental restorations.

Citrus waste has been used as a source of bioplastic research in different ways. Because the juice industry produces significant amounts of residue each year, it would be advantageous to use the byproducts in the creation of new materials. For many years, researchers have been investigating an environmentally friendly way to take citrus and other organic waste and turn it into polymers that may be used, for instance, to produce bio-based and biodegradable films for food packaging. The goal of this study is to create biofilms from orange (OW) and ginger waste (GW) using an ultrafine grinder and study the films' properties. Since pectin has the ability to gel and because cellulosic fibres are strong, citrus waste has been studied for its potential to produce biofilms. After being washed, dried, and milled, orange and ginger waste were shaped into films using a casting process. Tensile testing was used to determine the mechanical properties of biofilms, while dynamic mechanical thermal analysis (DMTA), thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC) were used to determine their thermal properties. As the number of grinding cycles increased, the suspension's viscosity increased from 29 to 57 mPa.s for OW and from 217 to 376 mPa.s for GW while the particle size in the suspension significantly decreased. For OW and GW films, the highest tensile strength was 17 MPa and 15 MPa, respectively. The maximum strain obtained among all films was 4.8%. All the tested films were stable up to 150°C, and maximum degradation occurs after 300°C.

African scientific research faces formidable challenges, particularly with limited access to state-of-the-art measurement instruments. The high cost associated with these devices presents a significant barrier for regional research laboratories, impeding their ability to conduct sophisticated experiments and gather precise data. This predicament not only hampers the individual laboratories but also has broader implications for the African scientific community and the advancement of knowledge in developing nations—the financial cost barrier considerably impacts the research quality of these laboratories. Reflection on technical and economical solutions needs to be quickly found to help these countries advance their research. In civil Engineering, the thermal conductivity property is the most important measurement for characterising heat transfer in construction materials. Existing devices (i.e., conductometers) in a laboratory are expensive (approximately 30,000 euros) and unavailable for some African laboratories. The study proposes a new and affordable device to evaluate thermal conductivity in construction materials. The method involves establishing a thermal flux between a heat source ( from the Joule effect provided by steel wool where a current is circulating) and a cold source (generated by ice cube) under steady-state conditions. The development of the cylindrical prototype is based on the comparative flux-meter method outlined in the measuring protocol of the ASTM E1225 standard document. Experiments were conducted on four distinct materials (polystyrene, wood, agglomerated wood, and rigid foam). The results indicate a correct correlation between the experimental values obtained from the newly developed prototype and the reference values found in the literature. For example, concerning the experimental polystyrene study, the detailed case analysis reveals a good correlation, with a deviation of only 4%. The percent error found falls within the acceptable range indicated by the standards recommendations of the ASTM E1225 standard, i.e., within 5% acceptable error.

Urban public space comfort is vital for enhancing the quality of life and perceptions of livability, especially as climate change increasingly impacts outdoor thermal environments. This study investigates the use of ENVI-met, a 3D microclimate simulation tool, to assess thermal comfort concerning demographic factors like age and gender. While ENVI-met is often used to analyze urban microclimates, there is limited research on its application for simulating heat emission variations across different demographic groups. The findings highlight significant disparities in thermal stress vulnerability: elderly individuals are at higher risk due to elevated maximum PET values, while children experience broader ranges of thermal stress and higher baseline values. Despite cooling effects in the evening, children continue to face greater stress. The study emphasizes the need for tailored management strategies, as morning PET values are consistent but afternoon data reveals children’s ongoing vulnerability. Overall, the research calls for further investigation to enhance urban planning, thermal comfort strategies, and public health interventions amid rising temperatures. It advocates for expanding ENVI-met's capabilities to include diverse demographic factors, promoting a more comprehensive approach to urban resilience and well-being.

Black soldier fly larvae (BSFL) can use food by-products or residues as a growth substrate, and their use is considered a strategic solution to improve the sustainability and efficiency of animal production. BSFL need to be reared under controlled environmental conditions, as temperature can affect the welfare of the larvae and the efficiency of their bioconversion. The goal of this experiment was to test different diets: control, vegetable, carnivorous, omnivorous and to assess their effect on larval growth performance, chemical composition, and substrate temperature. BSFL (6-days-old) were randomly selected and allocated to one of the four diets for the entire experiment (8 days). The temperature in each container was measured twice daily using a thermal imaging camera. The vegetable diet led to significantly lower growth performance (p

Many studies on flexible strain and pressure sensors have been reported due to growing interest in wearable devices for healthcare. However, most are fabricated with multiple ingredients and complicated methods even though commercial textiles, such as cotton, nylon, polyester, and silk were used. Here we present flexible pressure and strain (motion) sensors prepared with only graphene oxide (GO) and commercial silk fabrics and yarns. The pressure sensors were fabricated by simply dipping the silk fabric into GO solution followed by thermal treatment at 400 °C for reduction of GO (rGO). The pressure sensors were made from rGO-coated fabrics, which were stacked in 3-, 5-, and 7-layers. The super-sensitivity of 2.58 ×103 kPa-1 at low pressure was observed in the 7-layer pressure sensor. The strain sensors were obtained from rGO-coated twisted silk yarns whose gauge factor was 0.307. Although this value is small or comparable to other sensors, it is appropriate for motion sensing. The results of this study show a cost-effective and simple method for the fabrication of pressure and motion sensors with commercial silk and GO.

Many historic buildings and monuments on the Salento Peninsula (Apulia, southern Italy) were built from locally quarried Miocene calcarenites belonging to the Pietra Leccese Formation (Late Burdigalian-early Messinian). The main facies consists of a homogeneous and porous biomicrite, pale yellow in color and fine- to medium-grained, very rich in planktonic Foraminifera and massive or thick-bedded in outcrop. Additionally, there are other facies among which Piromafo stands out for its aesthetic appearance, which is enhanced by its greenish-brown or greenish-grey colors. Its physical characteristics, in terms of thermal properties mainly due to the mineral content and fabric, make it a good refractory and insulation material. Piromafo occurs in the upper part of the Pietra Leccese Fm. and is repre-sented by a fine- to medium-grained glauconitic and phosphatic biomicrite with macrofossils, es-pecially Bivalves and Gastropods. Despite its important historical use as building and ornamental material, especially in the Roman and Baroque architecture, a research gap exists in the scientific literature describing the properties of the stone and their correlation. Therefore, the aim of this paper is to present a wide range of properties useful to explain the in-situ behavior and damage susceptibility of the stone in monu-ments and buildings, but also for selecting preservation treatments and strategies. Thus, an overall assessment of the main petrophysical and mechanical properties especially for restoration/conservation purposes was performed using both standard and unconventional tech-niques. Starting from rock fabric inspection, particular attention was given to the relationship be-tween pore-size distribution and, hydraulic and thermal properties of the material. Unconfined compressive strength, flexural strength and indirect tensile strength were also estimated.

Bone drilling is a common procedure used to create pilot holes for inserting screws to secure implants for fracture fixation. However, dis process can increase bone temperature, teh excessive heat can lead to cell death and thermal osteonecrosis, potentially causing early fixation failure or complications. We conducted a three-dimensional dynamic elastoplastic finite element model to evaluate teh propagation and distribution of heat during bone drilling and assess teh thermally TEMPeffected zone (TAZ) dat may lead to thermal necrosis. dis model investigates teh parameters influencing bone temperature during bone drilling, including drill diameter, rotational speed, feed force, and predrilled hole. Teh results indicate dat our FE model is sufficiently accurate in predicting teh temperature rise TEMPeffect during bone drilling. Teh maximum temperature decreases exponentially wif radial distance. When teh feed forces are 40 and 60 N, teh maximum temperature does not exceed 45 °C. However, wif feed forces of 10 and 20 N, both teh maximum temperature exceeds 45 °C wifin a radial distance of 0.2 mm, indicating a high-risk zone for potential thermal osteonecrosis. Wif teh two-stage drilling procedure, where a 2.5 mm pilot hole is pre-drilled, teh maximum temperature can be reduced by 14 °C. dis suggests dat higher feed force and rotational speed and/or using a two-stage drilling process could mitigate bone temperature elevation and reduce teh risk of thermal osteonecrosis during bone drilling.

The design complexity of the new generation of civil aero-engines results in higher demands on engines’ components, higher component temperature, higher heat generation, and, finally, critical thermal management issues. This paper will propose a methodological approach to create physics-based models for heat loads developed by sources as well as a systematic sensitivity analysis to identify the effects of design parameters on the thermal behaviour of civil aero-engines. The ranges and levels of heat loads generated by heat sources (e.g., accessory gearbox, bearing, pumps, etc.) and heat absorption capacity of heat sinks (e.g., engine fuel, oil, and air) are discussed systematically. The practical research challenges for thermal management system design and development for the new and next generation of turbofan engines will then be addressed through a sensitivity analysis of the heat load values as well as the heat sinks flow rates. The potential solutions for thermal performance enhancements of propulsion systems will be proposed and discussed accordingly.

This paper evaluates the potential of solar concentration technologies—compound parabolic collector (CPC), linear Fresnel collector (LFC) and parabolic trough collector (PTC)—as an alternative to conventional sources of energy for industrial processes in Latin America, where high levels of solar radiation and isolated areas without energy supply exist. The analysis is addressed from energy, economic and environmental perspective. A specific application for Argentina in which fourteen locations are analyzed is considered. Results show that solar concentration technologies can be an economically and environmentally viable alternative. Levelized cost of energy (LCOE) ranges between 2.5 and 16.9 c€/kWh/m² and greenhouse gas (GHG) emissions avoided range between 33 and 348 kgCO₂/(m²·year). CPC technology stands out as the most recommendable technology when the working fluid temperature ranges from 373K to 423K. As the working fluid temperature increases the differences between the LCOE values of the CPC and LFC technologies decrease. When 523K is reached LFC technology is the one which presents the lowest LCOE values for all analyzed sites, while the LCOE values of PTC technology are close to CPC technology values. Results show that solar concentration technologies have reached economic and environmental competitiveness levels under certain scenarios, mainly linked to solar resource available, thermal level requirements and solar technology cost.

In the present research, groups of nanolayered structures and nanohybrids based on organic green dyes and inorganic species are designated to act as fillers for PVA for inducing new optical sites and increasing its thermal stability through producing polymeric nanocomposites. In this trend, different percentages of Naphthol green B were intercalated as pillars inside the Zn-Al nanolayered structures to form green organic-inorganic nanohybrids. The two-dimensional green nanohybrids were identified by X-ray diffraction, TEM and SEM. According to the thermal analyses, the nanohybrid, which has the highest amount of green dyes, was used for modifying the PVA through two series. In the first series, three nanocomposites were prepared depending on the green nanohybrid as prepared. In the second series, the yellow nanohybrid, which was produced from the green nanohybrid by thermal treatment, was used to produce another three nanocomposites. The optical properties revealed that the polymeric nanocomposites depending on green nanohybrids became optical-active in UV and visible regions because the energy band gap decreased to be 2.2 eV. In addition, the energy band gap of the nanocomposites depended on yellow nanohybrids was 2.5 eV. The thermal analyses indicated that the polymeric nanocomposites are thermally more stable than that of the original PVA. Finally, the dual functionality of organic-inorganic nanohybrids that produced from the confinement of organic dyes and the thermal stability of inorganic species converted the non-optical PVA to optical-active polymer in a wide range with high thermal stability

In this work commercial 18650 lithium-ion cells with LiMn₂O₄, LiFePO₄ and Li(Ni_0.33Mn_0.33Co_0.33)O₂ cathodes were exposed to external heating in an Accelerating Rate Calorimeter (es-ARC, THT Company) to investigate the thermal behavior under abuse conditions. New procedures for measuring external and internal pressure change of cells were developed. The external pressure was measured utilizing a gas-tight cylinder inside the calorimeter chamber in order to detect venting of the cells. For internal pressure measurements, a pressure line connected to a pressure transducer was directly inserted into the cell. During the thermal runaway experiments, three stages (low rate, medium rate and high rate reaction) have been observed. Both pressure and temperature change indicated different stages of exothermic reactions, which produced gases or/and heat. The onset temperature of thermal runaway was estimated according to temperature and pressure changes. Moreover, the different activation energies for the exothermic reactions could be derived from Arrhenius plots.

As a major coal country, China faces the issue of significant gas emissions during the coal mining process. This study aims to improve the utilization efficiency of mine gas, reduce greenhouse gas emissions, and promote the low-carbon and green transformation of the coal industry. A 10kW gas regenerative thermal oxidation (RTO) experimental system was constructed. The effects of initial methane concentration, low-temperature flue gas proportion, and operating load on combustion temperature, methane oxidation rate, high-temperature flue gas energy, and system thermal efficiency were studied. The results show that when the combustion temperature is below 600°C, the CH4 combustion reaction cannot proceed effectively, and the system temperature continuously decreases and cannot be maintained stable. The experiment determines the stable operating methane concentration range of RTO. In this experimental system, the lower limit of the initial methane concentration is 0.28%, corresponding to an 86% methane oxidation rate. As the initial methane concentration decreases, the combustion temperature also decreases, and the methane oxidation rate follows suit. The higher the low-temperature flue gas proportion, the higher the combustion temperature, and the system thermal efficiency and output heat decrease with the increase of the low-temperature flue gas proportion. This experiment explores multiple factors affecting regenerative thermal oxidation, providing an basis for ensuring the safe and stable operation of the system and optimization. Improving the thermal insulation and heat exchange performance of the storage body can expand the lower limit of the initial methane concentration, thereby increasing the stability and thermal efficiency of the system.

Daylighting design is not only a stage of dimensioning glazed surfaces to provide sufficient natural light to an occupied space, but also a method of analysing how this matter can be achieved without unwanted effects, such as: gains and losses of heat, glare, and variations of the daylighting intensity, at various indoor distances and levels. According to the international regulations in force, glazed surfaces must be designed with a careful balance between the admission of natural light and thermal performance, such as heat loss in winter and heat gain in summer. In a novel project, it is essential to determine the optimal ratio of window-to-wall surface area. This necessity arises because the materials constituting the glazed surfaces of windows typically exhibit lower insulation properties compared to those of the building's walls. This methodology could be applied to building renovations when envelope modifications are possible and suitable. The case study presented in the paper highlights the energy consumed due to a group of windows with a large glazed area in an existing building, located in a temperate continental climate area. The energy consumption results from supplementary artificial lighting required to maintain adequate illumination for indoor activities and that to counterbalance heat loss during colder periods are evaluated. The analysis performed by modifying the glazed surface led to the identification of an optimum value of windows dimensions for an energy consumed minimum.

Thermal expansion of four alkaline-earth borates, namely Ca3B2O6 (0D), CaB2O4 (1D), Sr3B14O24 (2D) and CaB4O7 (3D), have been studied by in situ high-temperature powder X-ray diffraction (HTXRD). Strong anisotropy of thermal expansion is observed for the structures of Ca3B2O6 (0D) and CaB2O4 (1D) built up from BO3 triangles only: these borates exhibit the maximal expansion perpendicular to the BO3 plane, i.e. along the direction of weaker bonding in the crystal structure. Layered Sr3B14O24 (2D) and framework CaB4O7 (3D) built up from various B-O groups expand less anisotropically. Thermal properties of the studied compounds compared to the other alka-line-earth borates are summarized depending on the selected structural characteristics like anion dimensionality, residual charge per one polyhedron (BO3 BO4), cationic size, and structural com-plexity. For the first time these dependencies were established as an average for both types of polyhedra (triangle and tetrahedron) occurring in the same structure at the same time. The most common trends were identified for : (i) Melting temperature decreases as the dimensionality of the borate polyanion, and more precisely, as the residual charge per one polyhedron (triangle or tetrahedron) decreases; (ii) volumetric expansion decreases while the degree of anisotropy in-creases weakly when the residual charge decreases; (iii)both trends (i) and (ii) are most steady within borates built by the triangles only, while the borates built by both triangles and tetrahedra show a larger scatter in values.

In this study, 10%PTFE/PEEK blend were modified by potassium titanate whisker (PTW) and chopped glass fiber (GF), respectively. The blends were prepared by three-screw extruder. Through the investigation of thermal stability, tribological properties, mechanical properties and rheological behavior, the effects of reinforcing agents were determined. The results illustrated that the mechanical properties of 10%PTFE/PEEK blend can be dramatically improved by adding reinforcing agent of PTW or GF, and the reinforcing effect of GF was especially obvious. As for tribological properties, 1% addition was the best proportion. The friction coefficient and wear rate of the blend with 1% PTW were 0.283 and 4.97 × 10^-6 mm³/N · m, which decreased by 7.2% and 21% compared with those of the blend without reinforcing agent.

Utilizing NCEP/NCAR monthly reanalysis data alongside precipitation observations from 1936 monitoring stations across China spanning from 1966 to 2022, this study establishes a location index for the thermal low-pressure center situated over the Qinghai–Tibet Plateau. Temporal variations in the location index and summer (July) precipitation patterns in China were studied. Over the past six decades, thermal low-pressure centers have been predominantly positioned near 90°E and 32.5°N on the plateau, with their distribution extending from east to west rather than from south to north. The longitudinal and latitudinal position indices exhibit contrasting linear trends, with a positive trend observed during the 1970s and early 21st century and a negative trend in subsequent decades. Mutation analysis highlights pronounced weakening mutations occurring in 1981 and 1973, with the longitudinal index transitioning from an inter-annual cycle of approximately 6-8 years, while the latitudinal index displays quasi-cyclic oscillations of 5 and 8 and 12-14 years. Strong negative correlations are evident between the location indices and precipitation along the southeastern edge of the Qinghai–Tibet Plateau and in Southern China, contrasting with the positive correlations observed in the central-eastern plateau, northwest China, North China, and the Huang-Huai region. The influence of southerly airflow predominates over much of China east of the plateau, while northwest China experiences convergence between northerly and southerly airflow. Higher location indices correspond to weaker surface cold air masses and strengthened Western Pacific Subtropical and South Asian Highs south of the Yangtze River Basin, resulting in significantly reduced rainfall in the southern Yangtze River region and increased rainfall in northwest China.

The construction industry is a key driver of environmental change due to its extensive ‎use of resources and high levels of emissions, thus placing a significant burden on global ‎efforts towards sustainable development targets. A large portion of the environmental ‎footprint of buildings results from the energy required to sustain indoor comfort levels. ‎Therefore, enhancing the energy efficiency of existing buildings becomes critical in ‎reducing their environmental impact. This study examines the influence of increasing ‎thermal performance with the aim of reducing heating ‎demand. Thus, numerical modelling tools and different energy performance assessment meth-odologies have been used. ‎Specifically, it evaluates two existing residential buildings in Romania and compares ‎heating demand predictions using PHPP and Mc001-2022 methodologies across various ‎climatic data sets and case studies. The results reveal significant variability in heating ‎demand predictions, emphasizing the importance of methodological choice and climatic ‎data. The ‎study highlights that both PHPP and Mc001-2022 methodologies yield varying results ‎depending on the specific conditions and characteristics of each building. This variation in results underscores ‎the necessity for a nuanced and context-specific approach to energy performance ‎assessment, in-corporating multiple energy efficiency measures tailored to the unique ‎features of each building.

Nanocellulose (CNC) seems to be a promising surfactant, which, together with expandable graphite (EG), forms the essence of an effective natural-based fire retardant wood coating. In our research, the most suitable composition of the mixture was tested concerning good solubility, dispersion, and consistency. Favorable results were achieved with the formulation composed of a 4% CNC alkaline solution with 80 wt.% of selected EG. Subsequently, six different EG were used to prepare these wood fire retardant coatings. The effectiveness of treatments was verified using a test with a radiant heat source, where the test samples' relative weight loss, relative burning rate, and surface temperature during 600 sec were evaluated. All prepared formulations can be characterized as more or less equally effective. However, the best results were obtained with EG of GG 200 – 100 N, where the mass loss of the sample was 8.10 ± 1.24%. Very good results were also achieved by graphite 25 E + 180 HPH (8.70 ± 0.89%), which is similar to the previous one, even according to the microscopic assessment of the coating as well as the expanded layer. Graphite type 25 K + 180 (8.86 ± 0.65 %) shows the expanded layer's best cohesion, coating uniformity, and ease of application. The results of this work confirmed that the CNC coating itself has significant retardation effects.

This study provides a detailed numerical assessment of the productivity of single-slope solar stills across key cities in the Caspian region, including Aktau, Atyrau, Astrakhan, Makhachkala, Baku, Tehran, and Turkmenbashi. Employing a mathematical model based on heat balance equations and the 4th-order Runge-Kutta method, we simulated the distillation process under various climatic conditions. The results reveal that productivity is significantly influenced by geographic location and local meteorological conditions. Tehran demonstrated the highest productivity across all seasons, with values of 1.75 × 10³ kg/(m²·year) and an efficiency of 0.53, due to its optimal solar irradiation and ambient temperature. In contrast, Atyrau and Makhachkala exhibited lower productivity, particularly in colder months, highlighting the effect of ambient temperature on solar still efficiency. The analysis identified optimal water depth at 2 cm and insulation thickness between 4 and 9 cm for enhancing productivity in continental climates like Aktau. Additionally, the lowest cost of distilled water was $0.024 per kilogram in Baku. These findings align with existing literature, validating the numerical model's accuracy. Future research will explore integrating solar stills with other renewable and fossil fuel-based technologies.

During the last 100 years the planet has increased its temperature rapidly, this climate change could bring catastrophic effects for organisms and natural systems. One of the most affected groups is the ectotherms, due to their direct dependence on the environmental temperature. In recent years several studies analyse the effects of temperature and the thermal tolerance on several species of ectotherms. However, there are species whose thermal tolerances are still unknown. Such is the case of critically endangered species the Montseny Brook Newt (Calotriton arnoldi), endemic from the Montseny massif in Spain and whose thermal biology is unknown. Its critical situation makes essential to know its tolerance to cooling, warming and thermopreferendum in water environment where the newt lives. Three experimental procedures were conducted from the western and eastern subpopulations of C. arnoldi considering four classes separately (males, females, juveniles and larvae). The results obtained showed that the CTmax of the species exceeded 31°C, with a significant difference between the two populations. We found that the species tolerates well low temperatures (<1°C), because of the genera Calotriton is adapted to lives in cold waters with temperatures below 15º. Although the thermopreference of the species was expected to trend to cold temperatures, some individuals chose relatively high temperatures, obtaining a range of 11.7°C to 21.6°C. The results presented in this study are an advance in the knowledge of the thermal physiology of this species and support the importance of the temperature of the torrent on its survival. Knowing their thermal limits and their preferred temperature range will help to propose management measures that promote the conservation of streams and its riparian forest cover to mitigate the temperature increase due to climate change.

Solar electric and solar thermal energies are often considered as part of the solution to the current energy emergency. In the present work, a study of the characteristic length of tubes in flat photovoltaic-thermal (PVT) hybrid solar devices has been carried out using three heat transfer fluids: water, Emim-Ac ionic liquid and ionanofluid of graphene nanoparticles suspended in the above ionic liquid. Experimental measurements and numerical simulations have been performed using the HEATT® platform. Slower fluid velocities are recommended if high fluid outlet temperatures are the goal of the application, but this penalizes the overall thermal energy production. The characteristic process length, or most efficient distance at which heat transfer occurs, is not typically achieved in parallel tube PVT collectors; coil-type panels can improve the thermal and temperature performance of INFs in PVT solar collectors depending on the application.

Utilization of wasted heat instead of fuel combustion is effective to reduce primary energy consumption for mitigating global warming problem. Because wasted heat sources are not necessarily located close to areas of heat demand, one of the difficulties is that wasted heat has to be transferred from heat source side to heat demand side, which may require heat transportation over long distance. From this point we proposed and have examined new idea of heat transportation using ammonia-water as the working fluid which system is named Solution Transportation Absorption chiller, in short STA. Our previous studies of STA were mainly the experimental investigation with STA facility which cooling power was 25RT (90kW). As a result, the COP of STA was found almost same value 0.65 with the conventional absorption chiller without depending on the transportation distances. The simulation using AspenHYSYS also examined with same experimental condition. The experimental data showed good agreement with the simulation calculation. In this study, we examined the large-scale cooling power STA on simulation. The examination cooling powers were from 90 kW(25RT) to 3517 kW(1000RT). All cooling power achieved around COP 0.64 including pump power consumptions. In addition, we performed the dynamic simulation. As the results, there was no effect of pipeline size on the cooling capacities and mass flow rates. Furthermore, the stability time of the cooling capacities and mass flow rates were almost same regardless of the pipeline size and cooling capacity. In other words, STA may be achieved the same COP even though having various complex conditions compared with the conventional absorption chiller.

In recent years, several alternatives for improving the thermal comfort conditions inside buildings have been proposed. Among these alternatives, Thermally Activated Building Systems (TABS) have become of interest due to the benefits this technology brings to the building sector. The TABS are embedded in different building components and exchange heat with building envelope to improve the indoor air temperature. This review presents relevant results presented in the literature on the thermal behavior of TABS, the different types of TABS configurations, and the main parameters of TABS studied such as pipe separation, fluid inlet temperature, fluid velocity, and volumetric flow rate. The potential of TABS to improve thermal comfort conditions and provide energy savings is also discussed. Further, this study presents the different modes of application.

In this paper, the effect of microstructure on the thermal conductivity of plasma-sprayed Y₂O₃ stabilized ZrO₂ (YSZ) thermal barrier coatings (TBCs) is investigated. Nine freestanding samples deposited on aluminum-base superalloy are studied. Cross-section morphology such as pores, cracks, m-phase content, grain boundary density of the coated samples are examined by scanning electron microscopy (SEM) and electron back-scattered diffraction (EBSD). Multiple linear regressions are used to develop quantitative models which describe the relationship between the particle parameters, m-phase content and the microstructure such as porosity, crack-porosity, the length density of small-angle-crack and the length density of big-angle-crack. Moreover, the relationship between microstructure and thermal conductivity is investigated. Results reveal that the thermal conductivity of the coating is mainly determined by the microstructure and grain boundary density at room temperature (25 ℃) and by the length density of big-angle-crack, monoclinic phase content and grain boundary density at high temperature (1200 ℃).

Potassium-oxygen batteries (KOBs) are a promising energy storage technology with high theoretical en-ergy density, low overpotential and long cycle life. Cathode microstructure plays a significant role in the electrochemical performance of KOB. In this article, hierarchical porosity was introduced to commer-cially available carbon paper cathodes by the thermal pretreatment in air at different pretreatment times. This pretreatment modifies the properties, such as, surface area, defects, oxygen functional groups etc. and it has been found to enhance the discharge capacity and it result in reduction of dis-charge overpotentials.

Maintaining the optimal microclimate in broiler houses is crucial for bird productivity, yet enabling efficient temperature control remains a significant challenge. This study developed and validated a computational fluid dynamics (CFD) model to predict temporal changes in indoor air temperature in response to variable ventilation operations in a commercial broiler house. The model accurately simulated air velocity and airflow distribution for different numbers of tunnel fans in operation, with air-velocity errors ranging from -0.22 to 0.32 m s-1. The predicted airflow rates through inlets and cooling pads showed good agreement with measured values with an accuracy of up to 108.1%. Additionally, the CFD model effectively predicted temperature dynamics, accounting for chicken heat production and ventilation effect. The model successfully predicted the longitudinal temperature gradients and their variations during ventilation cycles, validating its reliability through comparison with experimental data. The study also explored different variable inlet configurations to mitigate the temperature gradient. The variable inlet adjustment showed the potential to relieve the high temperatures but may reduce overall ventilation efficiency or intensify temperature gradients, which confirms the importance of optimising ventilation strategies. This CFD model provides a valuable tool for evaluating and improving ventilation systems and contributes to enhanced indoor microclimates and productivity in poultry houses.

Previous studies separately addressed the impact of urban expansion on vegetation cover and thermal conditions, as well as its effect on moisture and drought indicators, using geospatial techniques. Some studies, such as those by Malah et al. (2021) and Niu and Li (2020), focused on assessing urban environmental quality using an environmental quality index without considering urban expansion. Meanwhile, other studies, like those conducted by Indrawati et al. (2020), primarily focused on evaluating urban environ-ments using an integrated environmental index consisting of four indicators (greenness, moisture, drought, and cumulative clustering). The study by Zhu et al. (2019) applied the same integrated environmental index (IEI) and, by comparing it with temperature, re-vealed a negative correlation illustrating the effects of the environmental index on land surface temperature (LST). These two studies could be utilized to construct an index assessing the environmental condition in Riyadh. This is the case in the present study, where the addition of a temperature indicator due to the hot desert nature of the study area created the Urban Environmental Thermal Index to evaluate the urban en-vironment and provide results suitable to this region. It is expected that the present study will align with the findings of previous relevant studies, showing a negative im-pact of urban expansion on urban environmental components.

The aim of this study is to analyse problems related to thermal mapping obtained from thermal data acquired from Unmanned Aerial Systems (UAS) equipped with thermal cameras. We focused on an accurate analysis of uncertainties introduced by the PIX4D Mapper software used to obtain the surface temperature maps of thermal images acquired by the UAS. To achieve this aim, we used artificial thermal reference during the surveys, as well as natural hot targets, i.e. thermal anomalies in the Pisciarelli hydrothermal system in Campi Flegrei caldera (CFc). Artificial thermal targets, expressly created and designed for this goal, are a prototype here called “developed thermal target” (DTT) made by the drone Laboratory at Istituto Nazionale di Geofisica e Vulcanologia - Osservatorio Vesuviano (INGV-OV). We show the results obtained by three surveys during which thermal targets were positioned on land at different flight heights of the UAS. Different heights were also necessary to test spatial resolution of the DTT with the used thermal camera as well as possible temperature differences between the raw images acquired by UAS with the thermal mapping obtained from the PIX4D Mapper software. In this work we have estimated the uncertainty that may be introduced by the mosaic procedure and furthermore we find an attenuation of the measured temperatures introduced by the different distances between the thermal anomaly and sensor. These results appear to be of great importance for the subsequent calibration phase of the thermal maps especially in cases where these methodologies are applied for monitoring purposes of volcanic/geothermal areas.

Membrane gas absorption technology and solar-assisted regeneration system are two promising approaches to reduce high energy consumption associated with carbon dioxide capture from coal fired power plants. In the present study, a solar-assisted hollow fiber membrane contactor (SOL-HFMC) power plant is proposed to capture and desorb CO₂ in hollow fiber membrane contactors with the assistance of solar thermal collectors. Techno-economic assessment and sensitivity analysis of the proposed system is carried out in three studied locations with different weather conditions for a 580 MWe pulverized coal power plant. Research results show that, the output capacity and net efficiency of the SOL-HFMC power plant are significantly higher than those of the reference power plant regardless whether TES system is applied or not. In addition, CEI of the SOL-HFMC power plant with TES system is 4.36 kg CO₂/MWh, 4.45 kg CO₂/MWh and 4.66 kg CO₂/MWh lower than that of the reference power plant. The prices of membrane, vacuum tube collector and phase change material should be reduced to achieve lower LCOE and COR values. Specifically for SOL-HFMC power plant with TES system, the corresponding vacuum tube collector price shall be lower than 25.70 $/m² for Jinan, 95.20 $/m² for Xining, and 128.70 $/m² for Lhasa, respectively. To be more competitive than solar-assisted ammonia-based post-combustion CO₂ capture power plant, the membrane price in Jinan, Xining and Lhasa shall be reduced to 0.012 $/m, 0.015 $/m and 0.016 $/m for the sake of LCOE, and 0.03 $/m, 0.033 $/m and 0.034 $/m for the sake of COR, respectively. The findings can provide guidance for decision-making and risk management strategies.

Abstract: Steamed ginseng water (SGW), the by-product generated from the heated processing of red ginseng, with high content of active substances, better skincare activities, and large amount output ineffective utilization, resulted in environmental pollution and resource waste. In current study, UHPLC-Q-Exactive-MS/MS liquid chromatography-mass spectrometry and multivariate statistical analysis were conducted to characterize the compositional features of the repeated thermal-treated SGW. The total sugar content, total sugar content, total reducing sugar content, total non-reducing sugar content, DPPH, ABTS+, Fe3+ reducing capacity, and the hydroxyl radical scavenging abilities were employed to evaluate the gross contents variation connect with anti-oxidant activities during heat processes. The result revealed the SGW content and antioxidant activity were highly correlated, the 7th SGW sample showed the highest content and the strongest ability on anti-aging capacities. 38 significant common differential markers were screened, by the four compared SGW groups (1- and 3-, 1- and 5-, 1- and 7-, and 1- and 9) through OPLS-DA analysis. The current study showed that the thermal proceeding times could be a vital index value during the recycling operation quality control of SGW, which has a huge potential in anti-aging cosmetic raw materials, In the meanwhile, our results provided a green, sustainable, low-cost thinking of rational application on ginseng resource.

Ab initio density functional theory molecular dynamics extensive calculations were used for the first time to evaluate stability conditions for relevant phases of InN. In particular, thermal decomposition of InN with formation of N2 molecules and pressure induced wurtzite – rocksalt solid-solid phase transition were established. The results consistent with available experimental data allowed a critical evaluation of potential and limitations of the proposed simulation method. The ab initio molecular dynamics as an efficient tool for simulations of phase transformations of InN including solid-solid structural transition and thermal decomposition with formation of N2 molecules has been demonstrated. It is of high interest because InN being important component of epitaxial quantum structures has still not been obtained as a bulk single crystal making difficult a determination of its basic physical properties and designing new applications.

Improper disposal of waste plastic has caused serious ecological and environmental pollution problems. Transforming plastics into high value-added chemicals can not only achieve efficient recycling of waste plastics, but also an effective way to control white pollution. The catalyst selectively breaks the C-C bond of polyolefin plastic under heat treatment and converts it into liquid fuel, thus realizing sustainable recycling of plastics and has a good development prospect. This review provides a detailed overview of the current development of catalytic pyrolysis, catalytic hydrolysis, solvent decomposition and supercritical hydrothermal liquefaction for cracking plastics to make fuel oil. The reaction mechanism, influencing factors and promoting effects of catalysts in various degradation technologies are analyzed and summarized and the latest proposed tandem reaction for degrading plastics is briefly introduced. Finally, some optimization paths of waste plastic pyrolysis to fuel oil technology are proposed: synergies between mixed raw materials, in-depth exploration of catalysts, design and manufacture of reactors that match the pyrolysis technology. All these are important research directions for promoting the industrialization of plastic pyrolysis to fuel oil.

Thermal comfort indices are risk indicators for environmental conditions in livestock production. Predictive models based on these indices of heat stress, respiratory frequency, and presence of heat waves for lactating cows, comparing the prediction and correlation between these factors, generate responses that can improve animal management regarding physiological responses to heat stress during the incidence of heat waves. Therefore, the objective was to develop predictive models for heat wave risk alerts based on thermal stress indices, physiological responses, and surface temperature of lactating cows. The region's climatic conditions were evaluated based on data on temperature, air humidity, wind speed, black globe temperature, solar radiation, dew point temperature, and precipitation compiled from a meteorological station. In the processing phase, a data set was discretized into classes to apply machine learning techniques to generate a classification model with cross-validation of the data. The performance of the classifiers was evaluated based on the metrics: accuracy, precision, sensitivity (recall), and Kappa statistics. Predicting the risk of heat waves for lactating cows can meet the need to predict the frequency of heat waves for decision-making in environmental, nutritional, and health management to minimize adverse impacts on production. The accuracy of Decision Tree models (J48), Naive Bayes, and Logistic Regression was equal to 96.72%, 96.72%, and 98.36%, respectively. The performance in the evaluation metrics of the Logistic Regression prediction model was better than that of the decision tree and Naive Bayes models.

This paper presents a comparative study of heat transfer performance of lattice structured heat sinks. 20 different unit cells were chosen and heat sinks were modelled in nTop with constant unit cell size. Al 6061 alloy was chosen for analysis due to its good thermal conductivity, low weight, low cost, and high strength. Steady state thermal analysis was performed using ANSYS with constant input parameters for all samples. Heat flux and temperature distribution within the heat sinks were analysed. The study aims to provide a comprehensive understanding of the thermal performance of lattice heat sink designs.

(1) Background: A wide literature based on loading and unloading bending tests has been carried out over the half past century for assessing the force released by superelastic wires. The aim of this investigation is not only to characterize a broadly described superelastic NiTi and a novel CuNiTi archwire, but also to provide novel insights into the load vs deflection profiles. A harmonic scenario for superelastic wires will be shown as temperature is kept constant at 37°C. However, a completely different picture will be highlighted as a temporary heating step up to 50°C is introduced within the force vs deflection profiles. (2) Methods: A variety of NiTi and a novel CuNiTi round and rectangular cross-section archwires have been investigated. Static 3-point bending tests up to a deflection level of 3.0 mm have been carried out for detecting the unloading force plateau levels occurring at 37°C. A hold deflection step of 5 min at deflection levels occurring along the unloading plateau extension is introduced. The effect of a temporary heating up to 50°C on the force plateau level released by the investigated wires is analyzed. (3) Results: Mechanical profiles suggest that the plateau force levels detected at 37°C are consistent with those broadly reported in the literature, but they only represent a single block puzzle of the force scenario that a superelastic wire releases during the orthodontic treatment. (4) Conclusions: Once a superelastic wire is bent and clinically applied, the effect of a temporary heating up to 50°C (e.g. hot food or drink ingestion) produces a significant plateau force increase whose magnitude depends on the deflection level. The highest force increase of about 50% and 40% have been detected at deflection levels located at the beginning of the unloading plateau extension for NiTi and CuNiTi wires, respectively.

Research into lightweight structural concrete using volcanic tuff is of great importance to the construction industry. These materials have excellent thermal insulation properties, which helps improve the energy efficiency of buildings. A three-factor experimental design was used to build the statistical model. The test methods used were methods for determining the crushability of volcanic tuff, determining the average density, compressive strength and thermal conductivity of lightweight structural concrete. The influence of basalt fiber on the properties of lightweight structural concrete has been determined. The optimal compositions of lightweight structural concrete using tuff have been selected. The compressive strength of lightweight structural concrete reached 32.0 MPa. The average density range is 1754.6-2114.0 kg/m³. Good thermal conductivity values ​​were obtained in the range of 0.653-0.818 W/m·K. The article obtained the optimal compositions of lightweight structural concrete using volcanic tuff as a filler.

Two heating surfaces with longitudinal fins are located within the closed channel inside the housing made of thermal insulation material. The air flow inside the channel was carried out by an axial fan. The heating of the fins is established by using two positive temperature coefficient heating elements (PTC). Air flows circularly from one finned surface to another, and after reaching the required temperature, it leaves the housing. In the heating system conceived in this way, a methodology based on transient thermal irreversibility of heating sources and circular air flow has been established. Volumetric air flow and circulation time within the channel were varied. The total entropy generated does not include hydraulic irreversibility, but transient thermal irreversibility of the air and heat sources. For conducting analytical modeling, the temperature of the PTC heater was considered constant at 423K and 473K. Volumetric air flow varied in the interval from 0.00001m3s-1 to 0.00006m3s-1. The experimental determination of the transient thermal entropy was performed at a much higher air flow rate of 0.005m3s-1 inside the closed channel. Due to the continuous increase in air temperature, the temperatures of both PTC heaters increased within the examined time interval of 300s. According to experimental testing, the total transient thermal entropy of the described heating system has a minimum after 175s from the start of the circular heating of the air. The minimum of transient entropy also implies the optimal time of channel opening and exit of heated air.

The oscillating heat pipe (OHP) is a new member in the family of heat pipes, and it has great potential applications in energy conservation. However, the fluid flow and heat transfer in the OHP as well as the fundamental effects of inner diameter on them have not been fully understood, which are essential to the design and optimization of the OHP in real applications. Therefore, by combining the high-speed visualization method and infrared thermal imaging technique, the fluid flow and thermal performance in the OHPs with inner diameters of 1, 2 and 3 mm are presented and analyzed. The results indicate that three fluid flow motions, including small oscillation, bulk oscillation and circulation, coexist or, respectively, exist alone with the increasing heating load under different inner diameters, with three flow patterns occurring in the OHPs, viz. bubbly flow, slug flow and annular flow. These fluid flow motions are closely correlated with the heat and mass transfer performance in the OHPs, which can be reflected by the characteristics of infrared thermal images of condensers. The decrease in the inner diameter increases the frictional flow resistance and capillary instability while restricting the nucleate boiling in OHPs, which leads to a smaller proportion of bubbly flow, a larger proportion of short slug flow, a poorer thermal performance, and easier dry-out of working fluid. In addition, when compared with the 2 mm OHP, the increasing role of gravity induces the thermosyphon effect and weakens the 'bubble pumping' action, which results in a little smaller and bigger thermal resistances of 3 mm OHP under small and bulk oscillation of working fluid, respectively.

Soil organic matter (SOM) is essential for nutrient cycling and soil carbon (C) accumu-lation, both of which are heavily influenced by the quality and quantity of plant litter. Since SOM dynamics in relation to plant diversity are poorly understood we investigated the effects of willow variety and mixture, and site on the soil C stocks, SOM chemical composition and ther-mal stability. Using pyrolysis-field ionization mass spectrometry we analysed the top 10 cm of soil from two 7-year-old experimental sites in Germany and Sweden, with monocultures and mixtures of two willow varieties (Salix spp.) belonging to different species. Overall, site had the strongest effect on SOM quality. Results showed significant variability across sites for willow identity and mixture effects on C accumulation and SOM chemistry. In the German site (Ros-tock), yearly soil C accumulation was higher (p < 0.05) for variety ‘Loden’ (1.0 Mg C ha-1 year-1) compared to ‘Tora’ (0.5 Mg C ha-1 year-1), whilst in the Swedish site (Uppsala), both varieties ex-hibited similar soil C accumulation rates of around 0.6 Mg C ha-1 year-1. Willow variety identity significantly affected SOM quality at both sites, while mixing had minor effects. Our findings emphasize the significance of site-specific context and variety or species identity in shaping soil C accumulation in willow plantations.

A thermal-oxidative aging test at 120°C was condutcted on Ethylene Propylene Diene Monomer (EPDM) vulcanizates of the semi-efficient vulcanization system. The effect of thermal-oxidative aging on EPDM vulcanizates was systematically studied by curing kinetics, aging coefficient, cross-linking density, macroscopic physical properties, contact angle, Fourier Transform Infrared Spectrometer (FTIR), Thermogravimetric analysis (TGA) and thermal decomposition kinetics. The results show that the content of hydroxyl and carbonyl groups as well as the carbonyl index increased with increasing aging time, indicating that EPDM vulcanizates are gradually oxidized and degraded. As a result, the EPDM vulcanized rubber chains were cross-linked, and its conformational transformation was limited and its flexibility was weakened. The thermogravimetric analysis demonstrates the thermal degradation of EPDM vulcanizates had competitive reactions of cross-linking and degradation, and the thermal decomposition curve can be divided into three stages, meanwhile the thermal stability of EPDM vulcanizates gradually decreases with the increase of aging time. The introduction of antioxidant in the system can promote the cross-linking speed and reduce the cross-linking density of EPDM vulcanizates, while inhibiting the surface thermal and oxygen aging reaction. This is attributed to the fact that the antioxidant can reduce the thermal degradation reaction level, but it is not conducive to the formation of a perfect crosslinking network structure and reduce the activation energy of thermal degradation of the main chain.

It’s very well known that the world's attention is currently focused on the energy transition. The energy security, in addition to the drive to reduce greenhouse gas emissions in order to limit global warming, and the generalization of the access to energy, have contributed to adoption of the Moroccan Energy Strategy with a strong focus on Renewable Energies (RE). Morocco is notoriously poor in conventional fossil primary energy resources with an energy dependence on the order of 90%. The energy crisis and that resulted from Covid-19 pandemic and the geopolitical conflicts, combined compounded with steady increase in demand have heavily affected the security and the stability of the country's energy situation. The transition to RE, by strongly engaging in the implementation of several solar, wind and hydro energy projects benefiting from the country's excellent solar and wind energy potential, has made the country the leader in RE in Africa. By 2030, the share of RE in the installed capacity is expected to reach 52%. In this work, an overview of the current situation of RE (particularly solar energy) in Morocco is provided, including, the potentials, obstacles and challenges, and future perspectives. Thanks to its high solar potential location, it’s predictable that Morocco effort will be focused on this field: the Erasmus Plus Innomed Project is a virtuous example of international cooperation, aiming at create a Solar Energy Network, in synergy with EU Partners.

A variety of factors ranging from ethnicity and occupants’ lifestyles to local climatic characteristics of any studied location and people’s age factors can affect thermal comfort assessment globally. Due to the detrimental impact of climate change, the building industry has started to implement energy efficiency schemes while considering the thermal comfort of vulnerable population both for the society and any sphere of economy. Although, considering human-based approaches have been neglected by other scholars in thermal comfort studies. This paper reviews energy effectiveness of state-of-the-art passive systems in providing neutral adaptive thermal comfort for elderly people, through exploring passive design strategies in four distinct climates namely, Canada, India, Abu Dhabi and the South-eastern Mediterranean basin. The aim of the study is to analyze the available data provided by the ASHRAE Global Thermal Comfort Database II version record 2.1. The main objective of the study is to develop an effective methodological framework for the on-going development of adaptive thermal comfort theory. To this extend, this study presents a comprehensive review on the assessment of energy effectiveness of passive design systems. To accomplish this, the impact of climate change factor in passive design systems was investigated. The meta-analysis method was adopted to determine the input variables for the statistical analysis. Cramer’s V and Fisher’s Exact tests were used to assess occupants’ thermal sensation votes (TSVs). The findings revealed that there are discrepancies detected between the in-situ field experiments and the data recorded in the ASHRAE Global Thermal Comfort Database II. According to the Köppen-Geiger climate classification, it was found from the study that the slightly high temperature fluctuations were identified in India where the weather is dry and savanna climate. The study findings contribute to the development of adaptive thermal comfort theory by reviewing the existing methodologies globally. Furthermore, a critical review on the significance of occupants’ age differences should be conducted in the identification of neutral adaptive thermal comfort.

This study aims to evaluate the effectiveness of inactivating Salmonella enteritidis in fresh chicken breast by irradiation using a combination of short-wave UV (0, 3, 6, 9, 12 and 15 J / cm2) and a natural antimicrobial such as caffeine (0, 5, 10, 15 and 20 nM/g) as alternative proposals to conventional techniques to reduce pathogens in food. The temperatures used were from 2 to 22°C. The most suitable models were double Weibull in 60% of cases with an adjustment of R2 0.9903-0.9553 and Weibull + cola, in 46.67%, with an adjustment of R2 of 0.9998-0.9981. Noting that the most effective combination in the reduction of Salmonella was 12 J/cm2 of UV light and 15 nM/g of caffeine, with a reduction of 6 CFU/g and an inactivation rate of 0.72. The synergistic effect was observed by increasing caffeine and UV light. Furthermore, the physic-chemical characteristics of the food matrix were not affected by the combination of both technologies. Therefore, these results suggest that this combination can be used in the food industry to effectively inactivate Salmonella enteritidis, without deteriorating product quality.

The study sought to determine solar irradiation in Homa Bay County which can be tapped and utilized in improving lives of residents of the region by converting the solar thermal energy in Home Bay to other forms of energy such as electric form, mechanical form and light. The study was done by assessing the local atmospheric conditions which included sunshine duration data and air temperature records for the period of two years and the data obtained subjected to statistical analysis to determine the localized characteristics of the resource. The characteristics that were examined include; seasonal and annual power expectations as well as resource reliability. The solar irradiance of Home County was found to be 768.0 W/m².

Timber-concrete composite (TCC) systems join the positive aspects of engineered wood products (good seismic behaviour, low thermal conductivity, environmental sustainability, good behaviour under fire if appropriately designed) with those of concrete (high thermal inertia, durability, excellent fire resistance). TCC facades are typically composed by an internal insulated timber-frame wall and an external concrete slab, separated by a ventilated air cavity. However, there is very limited knowledge concerning the performance of TCC facades, especially for what concerns their thermal behaviour. The present paper deals with the development and optimisation of a 2D CFD model for the analysis of TCC ventilated façades thermal behaviour. The model is calibrated and validated against the experimental data collected during the annual monitoring of a real TCC ventilated envelope in the north of Italy. Also, a new solver algorithm is developed to significantly speed up the simulation. The final model can be used for the time-efficient analysis and optimisation of the thermal performance of TCC ventilated facades, as well as other ventilated facades with external massive cladding, avoiding the expensive and time-consuming construction of mock-ups, or the use of comparably slow (conventional) CFD solvers that are less suitable for optimization studies.

What proportions should a thermally massive building have? How should the thermal mass be distributed? Should the "massing" change with the choice of material? This paper shows how to optimize the physical proportions of a building so that it synchronizes ambient heat exchanges in a natural feedback cycle. The internal mass is thermally coupled with buoyancy ventilation; the cycle is driven by the daily swing of outdoor temperature. Tripling up functions in this way—so that structural materials can reliably cool and power the ventilation for buildings—could help decarbonize the construction industry and provide an effective strategy for adapting to life-threatening heatwaves. Based on harmonic analysis, the method allows designers to thermally tune the form and mass of a building to meet chosen targets for temperature and ventilation in free-running mode. Once the optimal balance of exchange rates is known, design teams can proportionally vary the building height and ventilation openings against the surface area and thickness of an internal thermal mass. The possible permutations are infinite but parametrically constrained, allowing teams to fairly compare the functional and environmental credentials of different construction materials while they produce and evaluate preliminary options for organizing the exterior form and interior spaces of a building. An example study suggests that thin-shell structures of minimum weight, and even timber buildings, may be optimally tuned to produce ample ventilation and temperature attenuation.

The paper presents theoretical, experimental and numerical studies on the thermal behavior of mineral wool used in sandwich panels. The aim of this study is to investigate the thermal properties of mineral wool at elevated temperatures and provide a simple model that would allow to determine the heat propagation in sandwich panels during fire. The paper proposes a new method to experimentally evaluate thermal diffusivity, derived from theoretical premises. Experiments are conducted in a laboratory furnace, where specimens are placed and temperatures inside specimens are measured. Different methods are used to process the test results and calculate the thermal diffusivity of mineral wool. Finally, a numerical analysis of heat transfer using finite element method (FEM) is performed to validate the obtained thermal properties.

Investigations into the properties of generalized effective temperature are conducted across arbitrary dimensions. Maxwell-Boltzmann distribution is displayed for one, two, and three dimensions, with effective temperatures expressed for each dimension. The energy density of blackbody radiation is examined as a function of dimensionality. Effective temperatures for non-uniform temperature distributions in one, two, three, and higher dimensions are presented, with generalizations extended to arbitrary dimensions. Furthermore, the application of generalized effective temperature is explored not only for linearly non-uniform temperature distributions but also for scenarios involving the volume fraction of two distinct temperature distributions. Finally, the effective temperature is determined for a cryogenic system supplied with both liquid nitrogen and liquid helium.

The main development direction of energy efficiency technologies in construction is the creation of various materials with a complex structure and unique strength, thermal and other properties. The aerogel is a material with high porosity and excellent thermal insulation properties. This paper provides the state-of-the-art of aerogel applications for the additive manufacturing of energy efficient buildings. This work provides the experimental and numerical assessment results of thermal conductivity of aerogel-enhanced blanket, the experimental assessment results of thermal performance of aerogel-enhanced building structure, the experimental assessment results of the aerogel application as mixture powder component of the concrete mixture to printing building and the experimental assessment results of the aerogel application as parget powder component. Experimental results show the effect of aerogel powder component application: thermal conductivity decreased by 25%.

Demographic studies have revealed a strong association between exposure to high ambient temperatures during pregnancy and increased risks of preterm birth (PTB). The mechanism underlying this association is unclear, but it is plausible that altered placental function may contribute. In this study, we conducted differential gene expression analysis, gene set enrichment analysis (GSEA), and gene ontology (GO) analysis on bulk RNA-seq data from human placentas delivered at term and preterm during the warmer months compared to placentas delivered at term and preterm during the colder months in the UK. We detected 48 differentially expressed genes in preterm placentas delivered during the warmer months compared to preterm placentas delivered during the colder months, the majority of which were inflammatory cytokines and chemokines, including SERPINA1, IL1B, CCL3, CCL3L3, CCL4, CCL4L2, CCL20, and CXCL8. The GSEA positively enriched 17 signalling pathways, including the NF-κB, IL17, toll-like receptor, and chemokine signalling pathways, in warm-exposed preterm placentas, which were not observed in warm-exposed term placentas. The GO analysis revealed several biological processes, including neutrophil, granulocyte, monocyte, and lymphocyte chemotaxis, as well as inflammatory and humoral immune responses in warm-exposed preterm placentas, but not in warm-exposed term placentas. We conclude that maternal exposure to warm environmental temperatures during pregnancy alters the placental transcriptome towards inflammation and immune regulation, potentially leading to PTB.

In this study, we successfully synthesized a novel branched polyamide 6 with ε-caprolactam(CPL) and α-Amino-ε-caprolactam(ACL) through hydrolytic ring-open co-polymerization. The NMR characterization and rheological test result proved the existence of branched chain structure additionally. The branched chain structure caused a remarkable enhancement in the rheological properties. The met index(MFR),zero shear rate viscosity and storage modulus at low frequency region had a remarkable increase.The shear thinning phenomenon became more obvious. The thermal properties test determined by differential scanning calorimetry(DSC) showed that the melting point and crystallinity of co-polymers decreased with the increase of ACL addition.However, the crystal structure of the samples remained unchanged. The appropriate addition amount of ACL can improve the tensile mechanical properties of the co-polymers. When the amount of ACL was 1%, the tensile strength and fracture elongation rate of the co-polymers had the most significant increase.

The permeability, heat conductivity and reaction rate will be varied with the change of natural gas hydrate saturation, when thermal fluid injected into the natural gas hydrate reservoirs. In order to characterize the variation of physical field parameters with hydrate saturation, DDF-LBM was applied to simulate the hydrate dissolving process by thermal fluid injection under pore scale modelling. Based on the forced conjugate heat transfer case, the relaxation frequency of the thermal lattice in the pores is corrected. Based on the P-T phase equilibrium relationship of hydrates and considering the heat absorbed by the hydrate reaction, the solid-liquid state of the hydrate lattice is judged in real time, and the dynamic simulation of the heat flow solidification multi-physics field is realized. The simulation results show that the dissolution rate of hydrates by thermal fluid injection was higher than that by heating the hydrate surface alone, and was positively correlated with the hydrate saturation. On the basis of the above results, this paper provided exponential fitting equations between different hydrate saturations and average permeability, effective thermal conductivity, and inherent reaction rate. The fitting results show that saturation has a negative correlation with relative permeability and effective thermal conductivity, and a positive correlation with the inherent reaction rate. The above results can provide a reference basis for accurately describing the heat and mass transfer of natural gas hydrate under macro-scale.

The advancement in science and technology has led to luffa sponge (LS) being widely used as a natural material in industrial application as its polyporous structure and light texture. In order to enhance the utility of LS fibers as the reinforcement of lightweight composite materials, this study investigate its water absorption, mechanical properties, anatomical characteristic and thermal performance. Hence, moisture regain, tensile properties of LS fiber bundles were measured in accordance with standards and the structural characteristics were investigated via microscopic observation. Scanning electron microscopy (SEM) was used to observe the surface morphology and fracture surface of fiber bundles. Test results shows that the special structure where the phloem tissues degenerate to cavities had a significant influence on the mechanical properties of LS fiber bundles. Additionally, the transverse sectional area occupied by fibers in a fiber bundle (SF), wall thickness and ratio of wall to lumen of fiber cell, and crystallinity of cellulose had an impact on the mechanical properties of LS fiber bundles. Furthermore, the fiber bundles density of LS varies range of 385.46-468.70 kg/m³, much less than that of jute (1360.40 kg/m³) and Arenga engleri (950.20 kg/m³) while LS fiber bundles has superior specific modulus.

This paper offers a theoretical and experimental examination of the concurrent production of electricity and heat using photovoltaic thermal (PV/T) technology. The efficiency performance of the PV/T system is meticulously analyzed using MATLAB/Simulink software environments. Notably, the proposed PV/T system shows reliable performance, and its validity is confirmed through experimental validation on a test stand with a single PV/T panel positioned at a 45-degree angle to the horizontal and a 0-degree azimuth angle.