Hybrid inorganic-polymer nanocomposites can be employed in diverse applications due to the potential combination of desired properties from both the organic and inorganic components. The use of novel bottom-up in situ synthesis methods for the fabrication of these nanocomposites is advantageous compared to top-down ex situ mixing methods, as it offers increased control over the structure and properties of the material. In this review, the focus will be on the application of the sol-gel process for the synthesis of inorganic oxide nanoparticles in epoxy and polysiloxane matrices. The effect of the synthesis conditions and the reactants used on the inorganic structures formed, the interactions between the polymer chains and the inorganic nanoparticles, and the resulting properties of the nanocomposites are appraised from several studies over the last two decades. Lastly, alternative in situ techniques and the applications of various polymer-inorganic oxide nanocomposites are briefly discussed.

Joining of aluminium alloys to steels has been extensively studied, especially in the automotive sector. However, aluminium alloys are known to be difficult to join with steels when methods involving fusion welding are used because of hot cracking problem. Hence, a high strength joint between these dissimilar metals would be of benefit especially in reducing the weight of products. In this work the torch brazing method was applied to join AR500 steel with AA7075 aluminium alloy using Al-Si-Zn base filler metal at various flame times. The effect of the brazing work on the intermetallic phase formation and the mechanical strength of the joints were investigated. In this work, the maximum shear load obtained was 6460 N and the presence of the intermetallic phases had reduced the shear strength of the brazed joints. However, the torch brazing process using Al-Si-Zn filler metal had successfully facilitated the joining of these dissimilar metals.

Air pollutants such as volatile organic compounds (VOCs), nitrogen oxides (NOx), sulfur dioxide (SO2), as well as water pollutants including heavy metal, are harmful to human and environment. Effective control and reduction of their pollution is therefore an important topic for today’s scientists. Fly ash (FA) is a type of industrial waste that can cause multiple environmental problems if discharged into the air. On the other hand, because of its high porosity, large specific surface area, and other unique characteristics, the FA can also be used as a low-cost and high efficient adsorbent with some simple modifications. This paper reviews the effects of FA on treatment of the above air and water pollution based on our research experience over many years, including to the current status of global FA utilization, physicochemical properties, principle of adsorption, and the application direction of FA in the future. It focuses on the use of nanocomposite technology to fabricate functional FA fibrous membranes to adsorb VOCs from air, and treat heavy metal wastewater. This present review first describes the fabrication technology of FA nanocomposites and their mechanism of adsorption VOCs from air. Utilization of nanofiber technology to fabricate multi-functional FA emerging composite materials to mitigate air and water pollution has great potential in the future, especially use of pollutant material to control other pollutants.

Soil pollution has been estimated using soil analysis and leaching test. These methods could show different data from reality due to effects by soil properties such as grain size and mineral composition. Therefore, this study advocates a new assessment and monitoring method of heavy metal polluted soil using fruticose lichens. Lichens growing at abandoned mine sites and unpolluted areas in southwest Japan and their substrata were analyzed using inductively coupled plasma-mass spectrometry and X-ray fluorescence spectrometry to clarify the relationships between the heavy metal concentrations in lichens and soils, and their heavy metal absorption properties. Concentrations of Cu, Zn, As, and Pb in the lichens were positively correlated with those in the soil. Variability of the relationships did not depend on the lichen species, location, habitat, or the conditions of soils. The analyzed lichens had neither competitive nor antagonistic properties in their heavy metal absorption, which make them good biomarkers of heavy metal pollution of soil. The distribution maps of average heavy metal concentrations at each sampling region detected almost all of the Cu, Zn, and As pollution of soil. Therefore, lichens could be used in practical applications to assess Cu, Zn, and As pollution of soils.

The objective of this study was to investigate the concentration and spatial distribution patterns of six potentially toxic heavy metal elements (Mn, Zn, Cr, Pb, Cu and Ni) in bus station dusts in the Xifeng district of Gansu province, NW China. The contents were analyzed for Mn, Zn, Cr, Pb, Cu and Ni by using S8 TIGER Brochures wavelength dispersive X-ray fluorescence spectrometry. Geoaccumulation index (Igeo ), enrichment factor (EF), pollution index (PI) and integrated pollution index(IPI) were calculated to evaluate the heavy metal contamination level of bus station dusts. The results indicate that, in comparison with the background values of local soil, bus station dusts in Xifeng have elevated metal concentrations as a whole. The concentrations of heavy metals investigated in this paper are compared with the reported data of other cities. The results show that the arithmetic means of Mn, Zn, Cr, Pb, Cu and Ni are 440.8, 137.9, 60.0, 42.8, 33.5 and 19.8mg kg−1 respectively. The mean values of Igeo reveal the order of Ni<Mn<Cr<Cu<Zn<Pb. The high Igeo and EF for Cu, Zn and Pb in bus station dusts indicate that there is a considerable Cu, Zn and Pb pollution, which mainly originate from traffic and industry activities. The Igeo and EF of Ni, Mn and Cr are low and the assessment results indicate an absence of distinct Ni, Mn and Cr pollution in bus station dusts. The assessment results of PI also support Cu, Zn and Pb in bus station dusts presented middle pollution, and IPI indicates heavy metals of bus station dusts polluted seriously.

Schiff base macromolecules have been successfully synthesized, utilizing a classical chemistry route and a dielectric barrier discharge (DBD) plasma technique. The synthesis of monomeric units has been accomplished through typical reactions of aldehyde and amine functional molecules. The condensation polymerization of the Schiff base molecules has been instigated chemically, using p-toluene sulfonyl chloride in refluxed ethanol. The molecular weight of the obtained polymers was discovered to be 524,664 and 1,503,228 for polymers 4a and 4b, respectively. Additionally, the polymerization reactions were prompted, employing a Dielectric Barrier Discharge (DBD) atmospheric pressure air plasma technique. The DBD plasma demonstrated a very powerful routine to produce high molecular weights macromolecules, which could be an ecofriendly strategy to acquire this class of materials. Moreover, the complexation of polymer 4b with various metal moieties, Ru (II), Co (II), Cu (II), and Ni (II), has been executed in order to have a comparative study of their antitumor activity against MCF-7, A-549, HCT-116, and HepG-2 cell lines. Furthermore, the density functional theory was exploited to optimize the polymers and their complexes, and their HOMO-LUMO and energy gap were calculated, which was utilized to examine the inter/intra molecular charge transfer. The molecular electrostatic potential map was similarly quantified to investigate the reactive sites that are present in the investigated molecules. The result for the docking study confirmed that these complexed polymers adopted numerous important interactions with the amino acid of the targeted enzyme.

It is expected that two-dimensional (2D) metal nitrides (MNs), consisting of the elements of the 13th group of the periodic table and nitrogen, namely aluminium nitride (AlN), gallium nitride (GaN), indium nitride (InN) and thallium nitride (TlN) have enhanced physical and mechanical properties, due to a honeycomb graphene-like atomic arrangement, characteristic to these compounds. The basis for the correct design and improved performance of nanodevices and complex structures based on 2D MNs of the 13th group is the understanding of the mechanical response of their components. In this context, a comparative study to determine the elastic properties of metal nitride nanosheets was carried out making use of the nanoscale continuum modelling (or molecular structural mechanics) method. The differences in the elastic properties (surface Young´s and shear moduli, and Poisson´s ratio) found for 2D 13th group MNs are attributed to the bond length of the respective diatomic hexagonal lattice. The results obtained contribute to a benchmark in the evaluation of mechanical properties of AlN, GaN, InN and TlN monolayers by analytical and numerical approaches.

The arsRBC operon encodes a 3-protein arsenic resistance system. ArsR regulates the transcription of the operon, while ArsB and ArsC are involved in exporting trivalent arsenic and reducing pentavalent arsenic respectively. Previous research in Agrobacterium tumefaciens 5A demonstrated ArsR has regulatory control over a wide range of metal related proteins and metabolic pathways. We hypothesized that ArsR has broad regulatory control in other Gram-negative bacteria and set out to test this. Here, we use differential proteomics to investigate changes caused by the presence of the arsR gene in human microbiome-relevant Escherichia coli during arsenite (AsIII) exposure. We show that ArsR has broad-ranging impacts such as the expression of TCA cycle enzymes during AsIII stress. Additionally, we found that the Isc [Fe-S] cluster and molybdenum cofactor assembly proteins are upregulated regardless of the presence of ArsR under these same conditions. An important finding from this differential proteomics analysis was the identification of response mechanisms that were strain, ArsR, and arsenic specific, providing new clarity to this complex regulon. Given the widespread occurrence of the arsRBC operon, these findings should have broad applicability across microbial genera, including sensitive environments such as the human gastrointestinal tract.

As high strength and ultra-high strength steels are widely used in all kinds of modern welded constructions, a lot of research is carried out to investigate the mechanical properties of weldments of these steels but there is a scarce information on such important characteristic as their corrosion behaviour. This research focuses on the corrosion behaviour of weld metal of weldments of S906QL and S700MC steels. Weld metal was tested electrochemically in a 3,5% NaCl aqueous solution via potentiodynamic scan to determine corrosion rate and its dependence on welding gap. No influence of welding gap on corrosion rate was found but the experimental results suggested that corrosion rate depended on the chemical composition of filler material and the microstructure of weld metal.

Increasing the energy density and power of supercapacitors through hybrids of carbonaceous materials and metal oxides continues to be the subject of numerous research works. The correlation between specific capacitance and the properties of materials used as electrodes attracts great interest. In the present study, we have investigated composites (GO/Mn3O4) prepared by hydrothermal method with variable ratio GO/Mn3O4 and tested as supercapacitor electrode materials in three and two-electrode cells. The chemical characterization carried out by X-ray Photoelectron Spectroscopy and the adsorption techniques used have allowed the determination of the surface carbon and oxygen content, as well as its textural properties. In this work we have analyzed the contribution of the double layer and of the Faradaic reactions to the value of the final supercapacitance of the synthesized materials. Beyond empirically obtaining the electrochemical properties, these have been related to the physicochemical characteristics of the hybrids, to help design materials with the best performances for supercapacitor electrodes.

With a growing number of PCMs and new, suitable PCM candidates, an overview is not only important, but also increasingly complex. Classification of PCM was thus changed significantly in the past decades. A review of classification of PCMs from recent years shows that not only different classification criteria are used, but more important that they are often mixed, used inconsistently, even without a clear goal. Focusing on the main goal of current classification schemes, to give an overview of the material options for the search for new, suitable PCM candidates, including already established PCMs, a consistent classification is developed in a desktop study. For this, first, the general options for classification criteria are reviewed, and then the appropriate ones selected. Then, based on them a new, revised PCM classification is suggested. It is specifically detailed with regard to mixtures; for binary mixtures it is based on a literature review performed within the study. The result also stresses the importance of specific R&D: for pure substances the sources and the chemical modification, and for mixtures their optimization by new compositions, additives, etc.

Chitosan is a biodegradable polymer derived from chitin, that is a versatile material for various biological applications for its attractive properties such as biocompatibility, biodegradability, and non-toxicity. Furthermore, chitosan possesses Second Harmonic Generation properties, that are useful for bio-sensing applications. In this work we explored the possibility to exploit chitosan-based nanospheres as SHG-based bio-sensors, and also as carriers of 89Sr radionuclide, an Active Pharmaceutical Ingredient for radiopharmaceutical treatments in cancer therapy. To load opportunely the Sr ion on the nanospheres, we used a fructose-based Metal Organic Framework, of formula [Sr(C6H12O6)2(H2O)2]Cl2·H2O, because the sugar was able to drive the Sr ions on the chitosan matrix. The Sr-loaded chitosan nanospheres were synthetized, characterized, and their SHG response was measured. The results encouraged us to propose the nanospheres for theranostic purposes, i.e. at the same time valuable for both therapy and diagnostic applications.

The continuous casting process of helical fiber reinforced metal matrix composites was proposed, and the experimental equipment was designed and manufactured. The relationship model be-tween the process parameters and the helical shape of the fibers in the metal matrix is analyzed by differential geometry. Helical carbon fiber reinforced lead matrix composites were prepared under different conditions. When the melting temperature and cooling intensity were increased, the helical radius of helical carbon fiber in lead matrix was increased. When the fiber rotation speed was increased, the helical radius was decreased, and the helical pitch was de-creased proportionally. The experimental results are consistent with the process model. Carbon fiber rein-forced aluminum composites were prepared. Scanning electron microscopy showed that the infiltration between the aluminum matrix and the carbon fiber was not complete. As the volume fraction of carbon fiber which was added in composites is too small, the mechanical properties of the composites have not been significantly improved.

The dynamic equilibrium of iron homeostasis has an important role in sustaining metabolic and neurological functions during human life. Iron excretion is modest and unregulated hence this overall equilibrium is tightly regulated in normal conditions by increasing deficient or limiting excessive iron assimilation. Here we focus on neural tissue overload, dyshomeostasis that is preceded by excessive assimilation, disturbances in internal homeostasis or both. Normal steps in iron homeostasis include its uptake across the apical membrane of the enterocytes in a mildly acidic duodenal milieu by the major importer of ferrous iron, Divalent Metal Transporter 1 (DMT1) (Nramp2/DCT1/SLC11A2, solute carrier family 11 member 2) [1, 2], responsible for the uptake of Non-Transferrin Bound Iron (NTBI) and divalent metals [3], passage through enterocytes bound to a chaperone and crossing the basal membrane via the only known cellular ferrous iron exporter, ferroportin [4] with the iron bound to transferrin (Tf) as it exits. Cells in peripheral tissues largely utilize circulating iron after uptake by receptor-mediated endocytosis of Tf-bound Iron [5]. Derangement of duodenal NTBI absorption of iron and heavy metals is influenced by systemic iron metabolism associated with inflammation that leads to iron accumulation into peripheral tissues and potential development of neurodegenerative diseases, involving distribution and fine regulation of DMT1 also in the central nervous system, where inflammatory-related acidosis influences DMT1 uptake, via its action as a proton cotransporter. Pharmacological strategies to inhibit NTBI transport selectively will be illustrated in relationship to protection, particularly neuroprotection, against iron overload associated with acidosis, inflammation, neuroinflammation and subsequent neurodegeneration.

In the ongoing transition from fossil fuels to renewable energies, advances are particularly expected regarding safe and cost-effective solutions. Publicising instances of such advances and emphasising safety considerations constitute the rationale for this communication. Knowing that high-strength steels can prove economically relevant for transporting hydrogen in pipelines by limiting the pipe wall thickness required to withstand high pressure, one advance relates to a bench designed for contributing to study the safety of the gaseous transport or renewable-energy-related buffer storage of hydrogen. That bench has been specifically implemented at technology readiness level TRL 6 for testing initially intact, damaged, or pre-notched DN 300/NPS 12, DN 600/NPS 24, and DN 900/NPS 36 pipe sections in order to provide data allowing for the possible validation of fully satisfactory predictive models in terms of hydrogen embrittlement and potential corollary ruin. The other advance relates to the reactivation of a previously fruitful applied research into mass solid-state hydrogen storage through a new public-private partnership. This latest development comes at a time when markets have started driving the hydrogen economy, bearing in mind that phase-change materials decisively allow levelling the heat transfers during the absorption/melting and solidification/desorption cycles and attaining an overall energy efficiency of up to 80% for MgH₂-based compacts doped with expanded natural graphite.

Currently, the textile industry is among the most rapidly expanding areas of the economy and is an important source of water pollution. There are many efficient chemical and physical methods for treating textile effluent, but they produce secondary pollutants. Therefore, there is a need to manage the textile waste wastewater. The potential EPS-producing and plant growth-promoting rhizobacteria Lysinibacillus capsici PB300 (T) bacteria strain has been isolated from the bark borer-affected Peltophorum pterocarpum plant and has been determined to be effective in > 95 decolorizing Reactive Red 120, and other azo dyes such as AB11385%, orange II 94.62%, Congo red 94.62%, phenol red 94.54%, and mixtures of azo dyes 81.66%. Physico-chemical factors were optimized manually, including Taguchi design. EPS production, PGPR strain, and fabric discoloration of L. capsici were qualitatively studied. The FTIR, GC-MS, and UV absorbance studies also confirmed that the dye had been broken into its amines. Research findings using enzyme assays have shown that the bacteria Lysinibacillus capsici PB300 (T) can utilize laccase and manganese peroxidase and are capable of degrading dyes significantly. According to this work, immobilised L. capsici cells and the studied four bacterial consortiums, Lysinibacillus capsici PB300 (T), Alcaligenes faecalis subsp. Phenolicus DSM 16503 (T), Acinetobacterbaumanni ATCC 19606 (T), and Pseudomonasaeruginosa JCM 5962 may be employed to degrade RR120 effectively, and it is concluded that L. capsici PB300 (T) bacteria is significantly efficient in textile effluent treatment.

Supramolecular structures with specific applications are a pillar in several areas of science. Thus, from a contemporary point of view, there are several reasons to feel inclined to cover a systematic, or historic critique of the supramolecular concept itself. First, the idea of a supramolecular material seems more secure now than it was decades ago. Second, updating the interacting of MOFs and supramolecular chemical and conversely, supramolecularity to assemble MOFs and to make ef-ficient complex systems in multiple cutting-edge applications. Third, we should here simply confine to a consideration of how workers in this field have tried to correlate the notion of the idea of supramolecular systems linking self-assembly considerations. Thereby, this is clearly an ad-vantage that optimized geometries obtained on the conductive bases described that undoubtedly, some of these systems have substantial applications and create a significant practical interest. The outline of this review encompasses a general introduction to MOFs and supramolecularity, the key unit of the study presented here, followed by a survey of recent advances in supramolecular chemistry in confined space, relationships of MOFs with the supramolecular chemistry, electro-chemical synthesis of MOFs, and switchable MOFs. Finally, some discussion on possible future perspectives of this field is given.

Bicyclic peptides have attracted the interest of pharmaceutical companies because of their remarkable properties putting them on a new path in medicine. Their conformational rigidity that improves proteolytic stability, leads to rapid penetration into tissues via any possible route of administration and elimination, occurring by renal metabolism, is of great importance for people with a history of liver diseases. In addition, each ring can function independently, making them extremely versatile molecules for further optimization. In this paper we compared the potentiometric and spectroscopic properties studied by UV-Vis, MCD, and EPR, of four synthetic analogues of the bi-cyclic peptide c(PKKHP-c(CFWKTC)-PKKH). In particular we correlated the structural and spectral properties of complexes with coordinating abilities toward Cu(II) ions of MCL (Ac-PKKHPc(CFWKTC)PKKH-NH2) that contains the unbinding cycle and N- and C-terminal linear parts, with two histidine residues, one per part; two monocyclic ligands containing one histidine residue, both in the N-terminal position i.e., MCL2 (Ac-PKKHPc(CFWKTC)PKKS-NH2) and in the C-terminal position i.e., MCL3 (Ac-PKKSPc(CFWKTC)PKKH-NH2), respectively, and the linear structure LNL (Ac-PKKHPSFWKTSPKKH-NH2).

Among the various types of gas sensors, the chemoresistive gas sensors based on metal oxides are considered the most attractive ones due to their simple operation, low costs and miniaturization. Thin films of V2O5 undoped and doped with TiO2 were studied as nitrogen dioxide, methane and hydrogen sensors. The experimental kinetics of the electrical conductivity changes due to introduction and removal of gas on metal oxide gas sensors were successfully explained in terms of the Langmuir adsorption theory.

Biopolymers are of growing interest, but to improve some of their poor properties and performance, it is required the formulation of bio-based blends and/or adding of nanoparticles. For this purpose, in this work, two different metal oxides, such as zinc oxide (ZnO) and titanium dioxide (TiO2), at different concentrations (0.5, 1 and 2 %wt.) have been added in polylactic acid (PLA) and polylactic acid/polyamide 11 (PLA/PA11) blends to establish their effects on solid-state properties, morphology, melt behaviour, and photo-oxidation resistance. It seems that the addition of ZnO in PLA leads to a significant reduction of its rigidity probably due to an inefficient dispersion in the melt state, while the addition of TiO2 does not penalise PLA rigidity. Interestingly, the addition of both ZnO and TiO2 in PLA/PA11 blend has a positive effect on the rigidity because of blend morphology refinement and leads to a slight increase in film hydrophobicity. The photo-oxidation resistance of neat PLA and PLA/PA11 blend is significantly reduced due to the presence of both metal oxides, and this must be considered when designing the potential applications. The last results suggest that both metal oxides could be considered as photo-sensitive degradant agents for biopolymer and biopolymer blends.

Present research focus on the effect of different processing routes on physical and mechanical properties of nano Ti(CN) based cermet’s with metallic binders. Tungsten carbide (WC) is added as secondary carbide and Ni-Co are added as metallic binders in nano Ti(CN) based cermet processed via Conventional and Spark Plasma Sintering (SPS). Systematic comparison of composition and sintering conditions for different cermet’s’ systems is done to design the novel composition and sintering conditions. Nano TiCN powder was prepared by 30hr of ball milling. Highest density of >98.5% percent was achieved for SPS processed cermet’s sintered at 1200°C and 1250°C for 3 min. at 60 MPa pressure in comparison to conventionally sintered cermet’s at 1400°C for 1hr with two stage compaction process, uniaxially at 150 MPa and isostatically at 300 MPa pressure respectively. Comparison of XRD analysis of milled powders of different time intervals was done to understand the characteristics of the as received and milled powders. Peak broadening was observed after 5 hr. of ball milling, and it increased till 30hr. Also, peak broadening and refined carbide size was observed in XRD and SEM micrograph of SPS processed cermet. TEM analysis of milled powder showed internal structure having regular periodic arrangement of planes. SEM (BSE) images of all cermets primarily showed three major microstructural phases of core-rim-binder with black, grey and white contrast respectively. In the present sintering conditions high hardness of ~16 GPa and fracture toughness of ~9 MPa m1/2 was obtained for SPS processed cermets sintered at higher temperature.

Biofilm serves as the residence for bacteria, wherein bacteria attach to surfaces and produce extracellular polymeric substances, including proteins, polysaccharides, and extracellular DNA. In recent years, biofilm reactors have gained increasing significance, playing a crucial role, for instance, in immobilizing heavy metals from waterways. This paper employs a bibliographic study to analyze the most important keywords and organizations in the field of biofilm reactors, identifying recent significant papers. Additionally, the paper discusses the opportunities for the future development of biofilm reactors. Through this study, a better understanding of key factors in biofilm reactor research is achieved, providing valuable guidance for future studies and applications in this field.

Metal halide perovskites have shown excellent optoelectronic properties, including high photoluminescence quantum yield, tunable emission wavelength, narrow full-width at half-maximum and low-cost solution-processed fabrication, which make it exhibit great potential as the emission layer materials of light emitting diodes. With the joint efforts of researchers from different disciplines, there has been a significant progress in the improvement of external quantum efficiency (EQE) and stability of perovskite light emitting diodes (PeLEDs) in recent few years, especially in green PeLEDs with EQE over 30%. In this review, we firstly introduce the basic device structure of PeLEDs, as well as the factors influencing EQE and stability of PeLEDs. Secondly, the development of lead-based and lead-free PeLEDs are summarized systematically. Thirdly, challenges of PeLEDs are discussed in detail, including low EQE of blue PeLEDs, poor device stability and EQE roll-off. Finally, some suggestions and perspectives of the future research directions for PeLEDs are proposed.

The CMT (Cold Metal Transfer) arc welding process is a convenient instrument for the assembly of thin sheets [1], [2]. More particularly, it permits the decrease of the amount of heat transferred to the parts to-be assembled, thus reducing their subsequent deformations. The present work aims at simulating the CMT welding of thin stainless-steel sheets in order to develop an approach that allows the prediction of temperature fields, as well as final deformations induced by the welding process. For that purpose, instrumented tests and numerical simulations were set aiming at comparing the experiments with simulations. Butt-welding of stainless-steel sheets was considered, with a thickness ranging from 1 to 1.2 mm. The weld seam samples were observed in order to set an equivalent heat source for each configuration. Moreover, the electric current and voltage were surveyed, and temperature measurements were performed using K-type thermocouples. In addition, displacement measurements were obtained using the DIC (Digital Image Correlation) technique. Thermomechanical simulations were then carried out using an equivalent heat source approach, considering the phase changes of elements, i.e. the transitions from solid to liquid and from liquid to solid. These simulations also consider the actual geometry of seams induced by addition of a filler material.

The results of a study of the processes of formation of macro- and micro-inhomogeneity of ingots and rolled sheets are presented. To study the nature and sources of surface defects in rolled sheets, a comparative method of structural-concentration analysis of metal at the end-to-end metallurgical process of ingot - slab - sheet metal has been developed, based on the metallographic method of studying the structure and qualitative analysis of non-metallic inclusions. The research results showed that the quality of the surface of rolled sheets is determined mainly by the physical heterogeneity of the crust zone of the ingots, and the internal defects of thin rolled sheets largely depend on the contamination of the metal with non-metallic inclusions and off-axis segregation. A mechanism for transforming defects in the casting cortical zone into surface and internal defects in rolled sheets is proposed.

The increading emission of carbon dioxide to the atmosphere has urged the scientific community to investigate alternatives to alleviate such emissions being the principal contributor to the greenhouse gas effect. One major alternative is carbon capture and utilisation (CCU) towards the production of value-added chemicals using diverse technologies. This work aims at the study of the catalytic potential of different cobalt-derived nanoparticels for methanol syntheis from carbon dioxide hydrogenation. Thanks to its abundance and cost-efficacy, cobalt can serve as an economical catalyst compared to noble-metal-based catalysts. In this work, we present a systematic comparison among different cobalt and cobalt oxide nanocomposites in terms of their efficiency as catalysts for carbon dioxide hydrogenation to methanol as well as how different supports can enhance their catalytic capacity. The oxygen vacancies in the cerium oxide act as carbon dioxide adsorption and activation sites, which facilitates a higher methanol production yield.

(1) Background: The synthesis of core-shell magnetic mesoporous nanoparticles (MMSN) from phase transfer process is usually performed at 100-250 mg scale. At the gram scale, nanoparticles without core or with multicore systems are observed. (2) Methods: Iron oxide core nanoparticles (IO) were synthesized through thermal decomposition procedure of -FeO in oleic acid. Phase transfer from chloroform to water was then performed in order to wrap IO with mesoporous silica shell through the sol-gel procedure. MMSN were then functionalized with DTPA, and used for the separation of metal ions. Their toxicity was evaluated (3) Results: The phase transfer pro-cedure was crucial to obtained MMSN at large scale. Three synthesis parameters were rigorously controlled: temperature, time and glassware. Homogeneous dispersion of MMSN at the gram scale was successfully obtained. After functionalization with DTPA, the MMSN-DTPA were shown to have a strong affinity for Ni ions. Furthermore toxicity was evaluated in cells, zebrafish and through seahorse metabolic assays, and the nanoparticles were found nontoxic. (4) Conclusions: We developed a method of preparation of MMSN at the gram scale. After function-alization with DTPA, the nanoparticles were efficient in metal ion removal and separation, fur-thermore, no toxicity was noticed up to 125 µg.mL-1 in zebrafish.

It is important to develop new antibacterial drugs since the emergence of bacterial resistance to available antibiotics. Metal nanoparticles have the potential to combat antibiotic resistance and are effective antibacterial agents. Here, we demonstrate the biogenic production of zinc nanoparticles using Rhododendron arboreum stem bark. The biosynthesized ZnNPs were characterized through different analytical techniques such as UV-vis, FTIR, EDX, SEM, and XRD. Clinical isolates such as E. coli, S. aureus, and K. pneumonia were used to check the antibacterial efficacy of the biosynthesized zinc nanoparticles. The MIC and MBC values against K. pneumonia, S. aureu, and E. coli were found to be 34±0.21 and 11.71±0.47, 47±0.11 and 23.86±0.84 and 94±0.18 and 40.43±0.16 µg/mL, respectively. It dramatically decreased the integrity of the cell membrane and markedly increased the permeability of both inner and outer membranes. The green synthesized ZnNPs have good catalytic activity. It degraded 65% of methyl orange dye within 6h when the mixture was kept in direct sunlight, thus demonstrating good photodegradation potential and can be employed as a good photocatalyst. According to these results, biosynthesized zinc nanoparticles could be a potential therapy option for controlling bacterial pathogenesis and an effective photocatalyst for the elimination of hazardous water contaminants.

Metal-organic framework (MOF) is a porous hybrid material of metal ions connected by organic bridging ligands. The coordination bonds link the metal ions, metal-ion clusters, and organic ligands to create the MOFs, and the materials are a distinctive class of crystalline frameworks. These porous materials possess relatively large surface area, tunable pore sizes, various functionalities, and high thermal stability. Therefore, diverse area of research including electrochemical sensor development utilizes distinctive and engineered MOFs materials. The review critically analyzes the strategy adopted for synthesizing a variety of MOFs materials. The role of these engineered materials in the fabrication of a miniaturized device demonstrates the detection of various emerging water contaminants in an aqueous medium. The studies demonstrated an understanding of the insights of sensor and device development. Moreover, the challenges encountered utilizing the MOFs in the electrochemical sensor development are precisely included, along with future perspectives of these studies.

Ionic gel electrolyte retains the characteristics of non-volatilization, non-flammability and outstanding electrochemical stability of ionic liquid, and shows good electrochemical performance combined with the excellent characteristics of different matrix materials, which is considered to be the best choice to achieve the high energy density and safety at the same time. In this paper, a flexible and self-healing ionic gel electrolyte is prepared by solvent-assisted method based on a zteric ion (ZI) copolymer. Abundant hydrogen bonds and synergistic interaction of ions in the electrolyte system endowed it with wonderful self-healing ability. The ionic conductivity of 9.06×10-4 S cm-1 at room temperature was achieved. Besides, the tLi+ was also increased to 0.312. The self-healing function of the ionic gel electrolyte ensured the long-term tolerance of the SHIGE. The capacity retention rate of the Li//LiFePO4 battery is 96% after 155 cycles at 0.1 C at 60 oC. This polymer electrolyte is expected to solve the problem of increasing polarization，which is caused by the low lithium ions migration number in ionic liquid electrolyte. And ultimately, it gives rise to a good rate performance.

In response to the growing demand for high-strength and high-toughness materials in industries like aerospace and automobiles, there is a need for metal matrix composites (MMCs) that can simultaneously enhance strength and toughness. This paper focuses on the design configurations of MMCs, which include both the configurations resulting from reinforcements and the inherent heterogeneity of the matrix itself. The mechanical properties of MMCs are influenced by factors such as reinforcement content, shape, size, and spatial distribution within the composite architecture. Among them, Aluminum matrix composites (AMCs) are particularly significant in aerospace, electronics, and electric vehicles due to their potential for weight reduction and enhanced performance. However, the challenge lies in the inverse relationship between strength and toughness, hindering the widespread utilization and large-scale development of MMCs. The design configuration of composites plays a critical role in achieving concurrent improvements in strength and toughness. This review explores the advantages of toughness, toughening mechanisms, reinforcement distribution characteristics, and structural parameters in the design of composite architectures. Drawing inspiration from biological composites like bone, the development of synthetic composites with homogeneous structural designs provides insights into attaining exceptional strength and toughness in lightweight engineering structures. Additionally, understanding fracture behavior and toughening mechanisms in heterogeneous nanostructures is vital for advancing the field of metal matrix composites. Summarily, the design of composite architectures holds tremendous potential for tailoring AMCs with outstanding strength and toughness, addressing the requirements of lightweight engineering structures in various industries.

Evidence of the efficacy and safety of colorectal stent placement for palliation remains insufficient. This single-arm, prospective, multicenter study with WallFlex enteral colonic stent included 200 consecutive patients with malignant large bowl obstruction in the palliation cohort. The technical and clinical success, as well as stent patency and complications as short-term (≤ 7 days) and long-term (&gt; 7days) outcomes, of high axial force self-expandable metal stent (SEMS) placement was evaluated. The technical and clinical success rates were 98.5% and 94.5%, respectively. Non recurrent colorectal obstruction at 1 year was 63.9%, and 71.2% of the patients remained free of recurrent colorectal obstruction until death or the last follow-up. Fifty-six patients (28.0 %) received chemotherapy and five patients were administered bevacizumab after stent placement. The overall complication rate was 47%, including four (2.0%) early-onset and ten (5.0%) late-onset perforations, mostly due to stent-edge injury. Only the use of a long SEMS was a risk factor for perforation. In conclusion, endoscopic colorectal stenting using high axial force SEMS is an effective and safe procedure for palliation in patients with malignant colorectal obstruction. However, care should be taken to avoid perforation at the stent edge when using a long SEMS.

To study the influence of electrothermal effect of ESD protection device on the reliability of inte-grated circuit,a theoretical model of ESD protection device thermal resistance is constructed in the paper based on the Conservation of Energy Principle. By analyzing the temperature relativity between electricity parameter and thermology parameter of ESD protection device characterized by self-heating thermal resistance, the quantitative relationship expression of physical parameter and geometric parameter is obtained, which can be used to improve ESD protection device elec-tro-thermal effect. The simulation testing and the real tape-out testing of ESD protection device self-heating thermal resistance based on ggNMOS are shown and compared. It is concluded that self-heating thermal resistance is an effective index for the protection device electrothermal char-acterization. Based on the established model, the self-heating thermal resistance could be decreased to improve the homogeneity of the heat transference. The uneven distribution of device temperature can be reduced, and the overall reliability of chips can be improved.

The spike protein (S) of SARS-CoV-2 has been shown to bind to the human angiotensin-converting enzyme 2 (ACE2) receptor with much higher affinity compared to other coronaviruses. The binding interface between the ACE2 receptor plays a critical role in the entry mechanism of SARS-CoV-2 virus. There are specific amino acids involved in the interaction between S protein and ACE2 receptor. This specificity is critical for the virus to establish a systemic infection and cause COVID-19 disease. In the ACE2 receptor, the largest number of amino acids that play a crucial role in the mechanism of interaction and recognition with the S protein are located in the C-terminal part which represents the main binding region between ACE2 and S. This fragment is abundant in coordination residues such as aspartates, glutamates and histidine that could be targeted by metal ions. Zn²⁺ ion binds to the ACE2 receptor in its catalytic site and modulates its activity, but it could also contribute to the structural stability of the entire protein. The ability of the human ACE2 receptor to coordinate metal ions, such Zn²⁺, in the same region where it binds to the S protein could have a crucial impact in the mechanism of recognition and interaction of ACE2-S with consequences on their binding affinity that deserve to be investigated. To test this possibility, this study aims to characterize the coordination ability of Zn²⁺, and also Cu²⁺ for comparison, with selected peptide models of the ACE2 binding interface using spectroscopic and potentiometric techniques.

Endoscopic ultrasound-guided gallbladder drainage (EUS-GBD) is an alternative to surgery for acute cholecystitis (AC) in poor operative candidates. However, the role of EUS-GBD in non-cholecystitis (NC) indications has not been well studied. We compared clinical outcomes of EUS-GBD for AC and NC indications. Consecutive patients undergoing EUS-GBD for all indications at a single center were retrospectively analyzed. Fifty-one patients underwent EUS-GBD during the study period. Thirty-nine (76%) patients had AC while 12 (24%) had NC indications. NC indications included malignant biliary obstruction (n = 8), symptomatic cholelithiasis (n = 1), gallstone pancreatitis (n = 1), choledocholithiasis (n = 1), and Mirizzi’s syndrome (n = 1). Technical success was noted in 92% (36/39) for AC and 92% (11/12) for NC (p &gt; 0.99). Clinical success rate was 94% and 100%, respectively (p &gt; 0.99). There were 4 adverse events in the AC group and 3 in the NC group (p = 0.62). Procedure duration (median 43 vs 45 minutes, p = 0.37), post-procedure length of stay (median 3 vs 3 days, p = 0.97), and total gallbladder related procedures (median 2 vs 2, p = 0.59) were similar. EUS-GBD for NC indications is similarly safe and effective as EUS-GBD in AC.

Two solvated rhenium(IV) complexes with formula [ReCl4(bpym)]·MeCN (1) and [ReCl4(bpym)]·CH3COOH·H2O (2) [bpym = 2,2'-bipyrimidine] have been prepared and characterized by means of Fourier transform infrared spectroscopy (FT–IR), scanning electron microscopy and energy dispersive X-ray analysis (SEM–EDX), single-crystal X-ray diffraction (XRD) and SQUID magnetometer. 1 and 2 crystallize in the monoclinic system with space groups P21/n and P21/c, respectively. In both compounds, the Re(IV) ion is six-coordinate and bound to four chloride ions and two nitrogen atoms of a 2,2’-bipyrimidine molecule forming a distorted octahedral geometry around the metal ion. In the crystal packing of 1 and 2, intermolecular halogen⋯halogen and π⋯halogen type interactions are present. Hydrogen bonds take place only in the crystal structure of 2. Both compounds exhibit an akin crystal framework based on halogen bonds. Variable-temperature dc magnetic susceptibility measurements performed on microcrystalline samples of 1 and 2 show a similar magnetic behavior for both compounds, with antiferromagnetic exchange between the Re(IV) ions connected mainly through intermolecular Re-Cl···Cl-Re interactions.

We have detected a large Nernst effect in the CDW state of the multiband organic metal α−(BEDT−TT)2KHg(SCN)4. We find that there exists a significant gradient of charge relaxation processes that can generate a sizeable contribution adding especially to the transverse thermoelectric signal. Apart from the phonon drag, the energy relaxation processes governing the electron-phonon interactions and the momentum relaxation processes governing the charge mobility of the q1D group of carriers have a significant role in observing the large Nernst signal in the CDW state. The emphasised momentum relaxation dynamics in the low field CDW state is a clear indicator of a significant carrier mobility that can lead to the largest Nernst signal in this state. The momentum relaxation is reduced with increasing angle and magnetic field, i.e., in the high field CDW state which is reflected in the smaller Nernst effect amplitude. In this case only the phonon drag and electron-phonon interactions are contributing to the transverse thermoelectric signal. Our findings advance and change the previous observations on the complex properties of this organic metal.

Mechanochemical production of copper (II) isonicotinate Metal-Organic Framework ([Cu (INA)2]-MOF) and its modified magnetic iron composite ([Cu (INA)2]-MOF@Fe3O4]) allowed for the adsorptive removal of Terbutaline from water. A variety of characterization techniques, including Fourier, transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), X-ray diffraction (XRD), and scanning electron microscopy (SEM), were used to elucidate the distinct chemical and morphological features of the two advanced materials. The optimal adsorption conditions were determined by investigating a wide range of adsorption-related variables, including contact time, initial Terbutaline concentration, adsorbent dosages pH, and temperature. The chemistry involved in the adsorption process between the adsorbents and the adsorbate molecules was evaluated using the best-fitting models, such as kinetics, isotherms, and thermodynamics, and the regeneration study was performed to evaluate the adsorbents' reusability. Incredibly maximum adsorption capacities (Qmax) of 1667 and 2500 mg L-1 were attained within 40 minutes under alkaline pH 11 by the [Cu (INA)2]-MOF and the [Cu (INA)2]-MOF@Fe3O4, respectively. The adsorbents have been proven to be good for the adsorption of Terbutaline as a priority pollutant in an aqueous solution, with pseudo-first order and Langmuir as the best-fitting models for the kinetic and isotherm models respectively.

How to effectively suppress thermal cracks in the metal laser additive manufacturing process is still one of the key issues to be solved in the field of laser additive manufacturing. Metal tin, with wide liquid phase working temperature range, high boiling point, low viscosity, high thermal conductivity and excellent electrical conductivity. The use of tin as an auxiliary thermal management material in the metal additive manufacturing process is expected to achieve effective regulation of the temperature field and stress field of the formed part, thereby inhibiting the initiation of cracks and obtaining formed parts with the target grain structure and high reliability. This paper presented a novel liquid metal-assisted laser additive manufacturing method (LMAAM). A numerical model for the laser additive manufacturing of tin-assisted titanium alloys was established. The differences of the flow field, temperature field and stress field of the formed parts with tin and without tin were compared and analyzed. The influence of the interaction position between the tin liquid level and the forming part on the temperature field and stress field of the forming part was deeply studied. The laser additive manufacturing experiment of tin-assisted titanium alloy was carried out, and the experimental results were basically consistent with the simulation results, which verified the validity of the model. LMAAM technology has proven to be an effective method for additive manufacturing of highly reliable formed parts.

All living organisms require some metal ions for their energy production as well as metabolic and biosynthetic processes. Within cells, metal ions are involved in the formation of adducts interact with metabolites and macromolecules (proteins and nucleic acids). The proteins that require binding to one or more metal ions to be able to carry out their physiological function are called metalloproteins. About one third of all protein structures in the Protein Data Bank involve metalloproteins. Over the past few years there has been a tremendous progress in the number of computational tools and techniques making use of 3D structural information to support the investigation of metalloproteins. This trend has been boosted also by the successful applications of neural networks and deep learning approaches in molecular and structural biology at large. In this review, we discuss recent advances in the development and availability of resources dealing with metalloproteins from a structure-based perspective. We start by addressing tools for the prediction of metal-binding sites (MBSs) using structural information on apo-proteins. Then, we provide an overview of methods for and lessons learned from the structural comparison of MBSs in a fold-independent manner. We then move to describing databases of metalloprotein/MBS structures. Finally, we summarize recent DL applications enhancing the functional interpretation of metalloprotein structures.

We report a prebiotically relevant solution to the N1-ribosylation of pyrimidine nucleobases, a well-known challenge in the RNA World hypothesis. It is found that the presence of metal cations and clay mineral enables the previously unachievable direct ribosylation of uracil, providing by far the highest yield. Spectroscopy and chromatography analyses confirmed the formation of ribosylated uracil. The method can also be extended to the ribosylation of 2-pyrimidinone. These findings are also compatible with the metal-doped-clay model developed by our lab for the unified route of the selection of ribose and subsequent syntheses of nucleotide and RNA.

The present study utilizes a metal inert gas welding (MIG) to make a dissimilar weld joint of different stainless steel grades AISI 304, 314, 316L, 420 and a standard structural steel S355MC to estimate the correlation of a microstructure and the mechanical properties. The microstructure of the base metals (BM), the heat affected zone (HAZ), the fusion zone (FZ) and the weld seam were analyzed using optical microscopy. Optical microscopy did not reveal any presence of weld defects such as porosity or cracks. The analysis of microstructure showed that both the austenitic and martensitic stainless steel weld structures contain some retained delta ferrite and coarse Me23C6 carbides in the HAZ, while the FZ exhibits delta ferrite and some retained austenite. The hardness profiles revealed difference between austenitic and martensitic steel welds that the later showed extremely high values in the HAZ (~500 HV/0.1) which causes fracture in this zone. The welds of all austenitic steel grades withstood tensile test, showing the average tensile strength of 472 MPa with fracture observed in the base metal zone. It made clear that the use of a filler rod 308LSI is suitable only for the austenitic stainless and structural steel dissimilar welds, and not appropriate for martensitic-structural steel welds. The achieved results revealed that the higher hardness of the martensitic phase in the HAZ of AISI 420 is closely related with the formation of untempered coarse martensitic structure and higher carbon content.

The screening and treatment of acid mine drainage (AMD) using Na₂FeO₄ has been explored. Elemental composition was performed using an ICP-OES for the raw and treated AMD. The AMD samples were collected from three different sampling sites (RTW1, RTW2 and RTW3) in Pretoria, South Africa with acidic pH ranging between 2.50 and 3.13. Total dissolved solids and Electrical Conductivity of AMD samples ranged between 960 and > 1000 mg. L^-1, 226 and 263 µS. cm^-1, respectively. The final pH of treated water samples increased up to ≥ 9.5 after treatment with Na₂FeO₄. Sodium ferrate showed dual functions by removing metals and raising the pH of the treated water. Concentrations of most trace elements were not complying with WHO and DWAF guideline standards in raw AMD while after treatment with Na₂FeO₄ the concentrations were below guidelines for domestic and irrigation purposes.

A series of polycaprolactones (PCLs) with molecular weights of 950–10,100 g mol−1 and Ð of 1.10–1.87 have been synthesized via one-pot, solvent-free ring-opening polymerization (ROP) of ε-caprolactone (CL) using a heterogeneous double metal cyanide (DMC) catalyst. Various initiators such as polypropylene glycol, ethylene glycol, propylene glycol, glycerol, and sorbitol are employed to tune the number of hydroxyl end groups and properties of the resultant PCLs. Kinetic studies indicate that the DMC-catalyzed ROP of CL proceeds via a coordination mechanism. Branched PCLs copolymers are also synthesized via the DMC-catalyzed copolymerization of CL with glycidol. The α,ω-hydroxyl functionalized PCLs were successfully used as telechelic polymers to produce thermoplastic poly(ester-ester) and poly(ester-urethane) elastomers with well-balanced stress and strain properties.

Alzheimer’s disease (AD) is one of the most prevailing neurodegenerative diseases, characterized by memory dysfunction and the presence of hyperphosphorylated tau and amyloid β (Aβ) aggregate in multiple brain regions, including the hippocampus and cortex. The exact etiology of AD has not yet been confirmed. However, epidemiological reports suggest that populations who were exposed to environmental hazards are more likely to develop AD than those who were not. Arsenic (As) is a naturally occurring environmental risk factor abundant in the Earth’s crust and human exposure to As predominantly occurs through drinking water. Convincing evidence suggests that As causes neurotoxicity and impairs memory and cognition although the hypothesis and molecular mechanism of As-associated pathobiology in AD are not clear yet. However, exposure to As and its metabolites leads to various pathogenic events such as oxidative stress, inflammation, mitochondrial dysfunctions, ER stress, apoptosis, impaired protein homeostasis, and abnormal calcium signaling. Evidence has indicated that As exposure induces alterations that coincide with most of the biochemical, pathological, and clinical developments of AD. Here, we overview existing literature to gain insights into the plausible mechanisms that underlie As-induced neurotoxicity and the subsequent neurological deficits in AD. Prospective strategies for the prevention and management of arsenic exposure and neurotoxicity have also been discussed.

Aiming the characterization of road dusts on the surrounding villages of an active mine and to assess metal(loids) bioaccessible fractions, a dust samples survey was undertaken. To achieve these objectives, pseudototal element concentration, mineralogical composition, Enrichment factor and in vitro extraction UBM assay for both gastric (G) and gastrointestinal (GI) phases, were determined. Results obtained revealed that arsenic represents the higher risk to humans, with mean pseudototal values higher than the maximum reference value range. Enrichment factor points to As significant to very high enrichment in all villages. Particles enriched in As, Ca, Fe, Cu, Al, Ti were identified by SEM-EDS in weathered agglomerates, linked to mine wastes and long-distance transport, both by wind and/or traffic. Arsenic bioaccessibility fraction (%BAF) presents low values in the studied samples, possibly due to low Fe complexes solubility with adsorbed As, limiting arsenic release and reducing its bioaccessibility. Concentrations of Cd bioaccessible G and GI phases are within the reference values range, while for Cu are above and for Pb are lower, than reference value range. Results show that the pseudototal fraction risk is overestimated when comparing to BAF (bioaccessible fraction), nevertheless, total G and GI risk are above the carcinogenic target risk (1.00E-06) in most samples. Carcinogenic risk of the bioaccessible contaminants shows that As is the element that represents higher risk for developing cancer over a lifetime, being ingestion the main risk route.

: Dacarbazine, DAC, 5-(3,3-dimethyltriazeno)imidazol-4-carboxamideis is an imidazole-carboxamide derivative, that is structurally related to purines. DAC belongs to the triazene compounds, which are a group of alkylating agents with antitumour and mutagenic properties. DAC is a non-cell cycle specific drug, active on all phases of cellular cycle. In the frame of this work the 3d-metal complexes (cobalt and copper) with dacarbazine were synthesized. Their spectroscopic properties by the use of FT-IR, FT-Raman and 1HNMR were studied. The structures of dacarbazine and its complexes with copper(II) and cobalt(II) were calculated using DFT methods. The effect of metals on the electronic charge distribution of dacarbazine was discussed on the basis of calculated NBO atomic charges. The reactivity of metal complexes in relation to ligand alone was estimated on the basis of calculated energy of HOMO and LUMO orbitals. The aromaticity of imidazole ring in dacarbazine and the complexes was compared (on the basis of calculated geometric indices of aromaticity). Thermal stability of the investigated 3d-metal complexes with dacarbazine and the products of their thermal decomposition were analyzed.

The paramagnetic gadolinium(III) ion is used as contrast agent in magnetic resonance (MR) imaging to improve the lesion detection and characterization. It generates a signal by changing the relaxivity of protons from associated water molecules and creates a clearer physical distinction between the molecule and the surrounding tissues. New gadolinium-based contrast agents displaying larger relaxivity values and specifically targeted might provide higher resolution and better functional images. We have synthesized the gadolinium(III) complex of formula [Gd(thy)2(H2O)6](ClO4)3·2H2O (1) [thy = 5-methyl-1H-pyrimidine-2,4-dione or thymine], which is the first reported compound based on gadolinium and thymine nucleobase. 1 has been characterized through vis-IR, SEM-EDAX and single-crystal X-ray diffraction techniques, and its magnetic and relaxometric properties have been investigated by means of SQUID magnetometer and MR imaging phantom studies, respectively. On the basis of its high relaxivity values, this gadolinium(III) complex can be considered a suitable candidate for contrast enhanced magnetic resonance imaging.

Bacteria a Microscopic organisms are the most inexhaustible and flexible of microorganisms and constitute a huge division of the whole living earthly biomass, certain microorganisms were found to amass metallic components at a high limit Was Known as Bacterial Bio-sorption Due to their little size, capacity to become under controlled conditions, and their Accommodation to an extensive variety of ecological situations; Potent metal bio-sorbents among microorganisms, at low pH esteems, cell divider ligands are protonated and contend essentially with metals for official. With expanding pH, more ligands, such as amino and carboxyl groups, could be exposed, leading to attraction between these negative charges and the metals, and consequently increment bio-sorption onto the cell surface. Starting with Isolation and identification of heavy metal-resistant bacteria from rock Ore. Studying Factors Affecting Uranium Bio-sorption, Optimization of bacterial growth conditions and optimum for metal uptake by free and immobilized bacterial cells and Desorption ratio of uranium ions adsorbed by Coli. /alginate, All this evidence suggest that functions groups Represented in our study are responsible for metal uptake in our bacterial biomass beside change in peaks position which assigned for it's groups confirm bio-sorption of metal ions from waste due to ions charge interaction comparing with immobilized we found increase in no of binding sites indicate that immobilized bacterial have high efficiency for metal up take which also change in peaks position which assigned for its groups confirm bio-sorption of metal ions from waste due to ions charge interaction, Where the high bio-sorption yield obtained by bacteria, the Uranium & heavy metal bioremediation process expects microorganisms to be joined to a strong surface.

In this article, it is proposed to use aluminum breakage scraps to obtain Green Hydrogen through the aluminum-water reaction with caustic soda as a catalyst. From this exothermic reaction, both hydrogen and the heat generated can be used. Due to the low price of aluminum chips, this allows us to produce Green hydrogen below the current price that is obtained using renewable energy sources and electrolyzers. On the other hand, we have developed a process that is sustainable since it is obtained as alumina and caustic soda waste that can be reused. This alumina obtained, once filtered, has high purity which allows us to produce high-quality primary aluminum without the need to use bauxite and reducing the production of red sludge. A comparative study-analysis has been carried out of two of the types of forms in which the most common aluminum is presented in the industry to analyze which one performs better by studying key factors such as the hydrogen produced, and the waste generated during the process. Finally, the mathematical model has been defined to be able to control the flow based on different key parameters such as temperature, molarity, and geometry. Undoubtedly, the study that we present represents a milestone for the recovery of metallic aluminum waste and may be of great interest to industries that use aluminum in their processes, such as recuperators, but also the vehicle or aerospace industry.

Hybrid metal-organic compounds as relatively new and prosperous magnetoelectric multiferroics provide opportunities to improve the polarization, magnetization and magneto-electric coupling at the same time, which usually have some limitations in the common type-I and type-II multiferroics. In this work we investigate the crystal of guanidinium copper(II) formate [C(NH2)3]Cu(HCOO)3 and give novel insights concerning the structure, magnetic, electric and magneto-electric behaviour of this interesting material. Detailed analysis of crystal structure at 100 K is given. Magnetization points to the copper(II)-formate spin-chain phase that becomes ordered below 4.6 K into the canted antiferromagnetic (AFM) state, as a result of super-exchange interaction over different formate bridges. The performed ab-initio colinear density functional theory (DFT) calculation confirm the AFM-like ground state as a first approximation and explain the coupling of spin-chains into the AFM ordered lattice. In versatile measurements of magnetization of a crystal, including transverse component besides the longitudinal one, very large anisotropy is found that might originate from canting of the coordination octahedra around copper(II) in cooperation with the canted AFM order. With cooling down in zero fields the generation of spontaneous polarization is observed step-wise below 270 K and 210 K and the effect of magnetic field on its value is observed also in the paramagnetic phase. Measured polarization is somewhat smaller than the DFT value in the c-direction, possibly due to twin domains present in the crystal. The considerable magneto-electric coupling below the magnetic transition temperature is measured with different orientations of the crystal in magnetic field, giving altogether the new light onto the magneto-electric effect in this material.

In recent years, the class of metal-organic framework (MOF) materials emerged. These materials' unique properties can be assigned to their structure, containing inorganic nodes connected with organic linkers. Due to their porosity and flexibility, MOFs have become suitable for various energy-related applications, including gas storage, hydrogen production and heterogeneous catalysis, and photocatalysis. Using DFT+U calculations, we show that the substitution of metal centers in inorganic nodes and the strain engineering of UiO-66 alters the electronic and optical properties of this material. We show that applying mechanical strain on UiO-66 enables the control of absorption coefficient in the UV-Vis spectrum and the photocatalytic processes' selectivity when reactants for several photocatalytic processes are present. The presented findings could lead to general strategies for designing novel MOFs for sustainable energy conversion applications.

Both types of surgical guides – with and without metal sleeves are founded beneficial in clinical studies. The aim of this in vitro study was to compare time of surgical procedure in dental implantology depending of used type of the surgical guide. Ten three dimensional (3D) printed models of lower jaws were prepared based on complete virtual model of patient clinical conditions with missing teeth 37, 46 and 47. Five of this models were used for implant sites preparation performed with use of surgical guide without metal sleeves and dedicated surgical kit, and next five were used for the same procedure performed with surgical guide with metal sleeves and dedicated surgical kit. Time of implant site preparation were measured and noted. Statistical analysis was performed using Student’s t test for independent samples. Difference of time in both groups were founded as statistically significant (t=-9.94; df =28; p=0.0000). Type of surgical guide is important factor which can impact on time of implant site preparation and all surgical procedure.

Sorghum is a multipurpose crop, but Cr(VI) toxicity influenced the production of the crop and have established highlighted courtesy, due to robust toxicity and a comparatively less known mode of action. Many reports approve the negative impact of Cr(VI) on plants. Yet, it is not clear that, at what concentrations, Cr(VI) inhibits the growth and nutrient quality of Sorghum. In the present research, toxic effects appeared after 1ppm of Cr treatment. The plant growth decreased 15 – 20% and nutritional quality decreased 30 – 40% significantly with increasing concentration of Cr(VI). Toxic components increased 14 – 16% with increasing concentration of Cr(VI) in both the varieties (HJ 541 and SSG 59-3). Chromium was accumulated more in roots followed by shoots with increasing Cr(VI) treatments (0-4 ppm). Chromium at 4ppm level was becoming lethal to Sorghum. Sorghum cultivar SSG 59-3 was more tolerable to Cr toxicity than HJ 541. Chromium accumulated in Sorghum and increased HCN content and at higher doses adversely affects the nutritive values and growth making it toxic for animal consumption. These findings may be useful for scheming a mitigation strategy for chromium toxicity.

: TiAl6V4 alloy is widely used in selective laser melting and direct laser melting. In turn, works devoted to the issue of how the track stacking scheme affects the value of mechanical properties is not enough. The influence of the Ti6Al4V alloy track trajectories on the microstructure and mechanical properties during direct laser deposition is studied in this article for the first time. The results were obtained on the influence of «parallel» and «perpendicular» technique of laying tracks in direct laser synthesis. All studied samples have a microstructure typical of the hardened two-phase condition titanium. It is shown that the method of laying tracks and the direction of load application during compression testing relative to the location of the tracks leads to a change in the ultimate strength of the Ti-6Al-4V alloy from 1794 to 1910 MPa. The plasticity of the Ti-6Al-4V alloy obtained by direct laser alloying can vary from 21.3 to 33.0% depending on the direction of laying the tracks and the direction of the compression test. The hardness of alloys varies in the range from 409 to 511 HV and depends on the method of laying the tracks and the direction of hardness measurements.

Metal 3D printing technology is a promising manufacturing method. The quality of the printed product can pass for mechanical application, if the anisotropy of the microstructure, imperfections, deformation, and residual stress of the printed sample could be lower than the appropriate level or if they are fully illuminated. Thermal stress is one of the significant reasons for deformation in the 3D printed samples. Thermal stresses are the direct consequence of the local temperature gradient. In this research, the effect of the temperature printer’s chamber (from room temperature to 900 C) was studied on thermal stress and subsequent total deformation in the printed sample. The printed sample is a six-layers-printed walk, which could be considered as a building block of other complex shapes and give us inside about deformation. The computational results show a meaningful reduction in thermal stress and deformation at the higher temperature of the printer’s chamber. The lower final deformation of the printed sample is an important subject, especially for samples with complex shapes.

Understanding potential uptake and biodistribution of engineered nanoparticles in soil-grown plants is imperative for toxicity and risk assessment considering the oral exposure of edibles by humans. Herein, we assessed potential influence of particle size (25, 50, and 250 nm) and concentration (0, 50, 100, 200, and 500 mg/kg-soil) of Copper oxide nanoparticles (CuONPs) on: (1) the root system architecture, and the physicochemical attributes of soil at the soil-root interface, (2) leading to Cu transport and accumulation in root, stem, leaf and seed in soybean (Glycine max cv Kowsar) grown for entire lifecycle of 120 days, and compared with soluble Cu²⁺ ions and water-only controls, and (3) performed a comparative assessment of total seed Cu levels in soybean with other valuable food sources for Cu intake and discussed its human health implications. Our findings showed particle size- and concentration-dependent influence of CuONPs on Cu uptake and tissue distribution in root, stem, leaf and seed in soybean. Alterations in root architecture (root dry weight, root length, root volume, and root area) were dependent on the Cu compound type, Cu concentrations, and their interactions (p<0.05), except for root density. Concentration-response relationships for all three sized CuONPs, and Cu²⁺ ions, were linear. CuONPs and Cu²⁺ ions had inhibitory effects on root growth and development. Overall, soybean responses to smallest size CuONPs-25 nm were higher for all parameters investigated compared to two larger sized CuONPs (50 nm, 250 nm) or Cu²⁺ ions. Cu uptake/bioaccumulation differed among soybean tissues in the order: root > leaf > stem > seed. Despite reduced root architecture and seed yield, our smallest size CuONPs-25 nm led to increased total seed Cu uptake compared to the larger sized CuONPs and Cu²⁺ ions tested. Our findings also suggest that soil amendment by CuONPs, more so by the smallest size CuONPs-25 nm, could significantly improve nutritional Cu value in soybean seed as reflected by % Daily Values (DV), and are rated “Good” to “Very Good” according to the “World’s Healthiest Foods” rating. However, until the potential toxicity and risk from consumption of soybean seed is characterized in humans, caution should be exercised when the Cu fortified seeds are used for daily human consumption when addressing Cu deficiency and associated illnesses, globally.

In this paper, a metal cutting machine position control have been designed and simulated using Matlab/Simulink Toolbox successfully. The open loop response of the system analysis shows that the system needs performance improvement. Static output feedback and full state feedback H₂ controllers have been used to increase the performance of the system. Comparison of the metal cutting machine position using static output feedback and full state feedback H₂ controllers have been done to track a set point position using step and sine wave input signals and a promising results have been analyzed.

Highly sensitive multicomponent materials designed for the recognition of hazardous compounds request control over interfacial chemistry. The latter is key parameter in the construction of the sensing (macro)molecular architectures. In this work, multi-walled carbon nanotubes (in short, CNTs) were deposited on diazonium-modified flexible ITO electrodes prior to electropolymerization of pyrrole. This three step process, including diazonium electroreduction, deposition of CNTs and electropolymerization, provided adhesively bonded polypyrrole-wrapped CNT composite coatings on aminophenyl-modified flexible ITO sheets. The aminophenyl (AP) groups were attached to ITO by electroreduction of the in situ generated aminobenzenediazonium compound in aqueous, acidic medium. For the first time, polypyrrole (PPy) was electrodeposited in the presence of both benzenesulfonic acid (dopant) and ethylene glycol-bis(2-aminoethylether)-tetraacetic acid (EGTA) which acts as a chelator. The flexible electrodes were characterized by XPS, Raman and scanning electron microscopy (SEM) which provided strong supporting evidence for the wrapping of CNTs by the electrodeposited PPy. Indeed, the CNT average diameter increased from 182.6 nm to 274.8, 35.65.9 and 17520.1 after 1, 5 and 10 of electropolymerization of pyrrole. The PPy/CNT/NH2-ITO films generated by this strategy exhibit significantly improved stability and higher conductivity compared to a similar PPy coating without any embedded CNTs as assessed by from electrochemical impedance spectroscopy measurements. The potentiometric response was linear in the 10-83×10-7 mol.L-1 Pb(II) concentration range and the detection limit was 2.9×10-9 mol.L-1 at S/N=3. The EGTA was found to drastically improve selectivity for Pb(II) over Cu(II). To account for this improvement, density functional theory (DFT) was employed to calculate the EGTA-metal ion interaction energy which was found to be -374.6 and -116.4 kJ/mol for Pb(II) and Cu(II), respectively, considering solvation effects. This work demonstrates the power of a subtle combination of diazonium coupling agent, CNTs, chelators and conductive polymers to design high-performance electrochemical sensors for environmental applications.

The development of sensors for monitoring Carbon Monoxide (CO) in a large range of temperature is of crucial importance in areas as monitoring of industrial processes or personal tracking using smart objects. Devices integrating GaN/Ga₂O₃ core/shell nanowires (NWs) is a promising solution allowing combining the high sensitivity of the electronic properties to the states of GaN-core surface; and the high sensitivity to CO of Ga₂O₃-shell. Because the performances of sensors primarily depend on the material properties composing the active layer of the device, it is essential to control these properties and in first time its synthesis. In this work, we investigate the synthesis of GaN/Ga₂O₃ core-shell NWs with a special focus on the formation of the shell. The GaN NWs grown by Plasma-assisted molecular beam epitaxy, are post-treated following thermal oxidation to form Ga₂O₃-shell surrounding the GaN-core. We establish that the Ga₂O₃-shell thickness can be modulated from 1 up to 14 nm by changing the oxidation conditions, and follows the diffuse-controlled reaction. By combining XRD-STEM and EDX analysis, we also demonstrate that the oxide shell formed by thermal oxidation is crystalline and presents the β-Ga₂O₃ crystalline phase, and is synthesized in epitaxial relationship with the GaN-core.

Food preservatives are compound that are used for the treatment of food to improve the shelf life. In the food industry, is necessary to monitor all processes, for both safety and quality of the product. An electronic nose (or e-nose) is a biomimetic olfactory system that could find numerous industrial applications, including food quality control. Commercial electronic noses are based on sensor arrays composed by a combination of different sensors, which include conductometric metal oxide devices. Metal oxide nanowires are considered among the most promising materials for the fabrication of novel sensing devices, which can enhance the overall performances of e-noses in food applications. In the present work, is reported the fabrication of a novel sensor array based on SnO2, CuO and WO₃ nanowires deposited on top of commercial μHPs, provided by ams Sensor Solutions Germany GmbH. The array was tested for the discrimination of four typical compounds added to food products or used for their treatment to increase the shelf life: ethanol, acetone, nitrogen dioxide and ozone. Results are very promising: the sensors array was able to operate for long time consuming less than 50mW for each single sensor, and PCA analysis confirms that the device was able to discriminate between different compounds.

The optimization of the production process of metal mines has been traditionally driven only by economic benefits while ignoring resource efficiency. However, it has become increasingly aware of the importance of resource efficiency since mineral resource reserves continue to decrease while the demand continues to grow. To better utilize the mineral resources for sustainable development, this paper proposes a multi-objective optimization model of the production process of metal mines considering both economic benefits and resource efficiency. Specifically, the goals of the proposed model are to maximize the profit and resource utilization rate. Then, the fast and elitist Non-Dominated Sorting Genetic Algorithm (NSGA-II) is used to optimize the multi-objective optimization model. The proposed model has been applied to the optimization of the production process of a stage in the Huogeqi Copper Mine. The optimization results provide a set of Pareto-optimal solutions that can meet varying needs of decision makers. Moreover, compared with those of the current production indicators, the profit and resource utilization rate of some points in the optimization results can increase respectively by 2.99% and 2.64%. Additionally, the effects of the decision variables (geological cut-off grade, minimum industrial grade and loss ratio) on objective functions (profit and resource utilization rate) were discussed using variance analysis. The sensitivities of the Pareto-optimal solutions to the unit copper concentrate price were studied. The results show that the Pareto-optimal solutions at higher profits (with lower resource utilization rates) are more sensitive to the unit copper concentrate prices than those obtained in regions with lower profits.

Light sources tend to affect images captured in any automatic optical inspection (AOI) system. In this study, the effectiveness of metal-halide lamps, quartz-halogen lamps, and LEDs as the light sources in AOI systems for the detection of the 3rd and 4th layers electrodes of thin-film-transistor liquid crystal displays (TFT-LCDs) is examined experimentally. The results show that the performance of LEDs is generally comparable or better than that of metal-halide and quartz-halogen lamps. The best optical performance is by the blue LED due to its spectrum compatibility with the time-delay-integration charged-coupled device (TDI CCD) sensor and its better spatial resolution. The images revealed by the blue LED are sharper and more distinctive. Since current LEDs are more energy efficient and environmentally friendly, using LEDs as the light source for AOI is very beneficial. As the blue LED performs the best, it should be adopted for AOI using TDI CCD sensors.

The apparent metal-insulator transition (MIT) in two-dimension (2D) was discovered by Kravchenko et al. [1] more than two decades ago in strongly interacting 2D electrons residing in a Si-metal-oxide-semiconductor field-effect transistor (Si-MOSFET). Its origin remains unresolved. Recently, low magnetic field reentrant insulating phases (RIPs), which dwell between the zero-field (B=0) metallic state and the integer quantum Hall (QH) states where the Landau-level filling factor υ > 1, have been observed in strongly correlated 2D GaAs hole systems with large interaction parameter rs (~20-40) and high purity. A new complex phase diagram was proposed, which includes zero field MIT, low magnetic field RIPs, integer QH states, fractional QH states, high field RIPs and insulating phases (HFIPs) with υ < 1 in which the insulating phases are explained by the formation of Wigner crystal. Furthermore, evidences of new intermediate phases were reported. All contribute to the further understandings of the puzzle. This review article serves the purpose of summarizing those recent experimental findings and theoretical endeavors, to foster future research efforts.

Metal-Organic Frameworks (MOFs) are a subclass of porous materials that have unique properties such as varieties of structures from different metals and organic linkers, tunable porosity from a structure or framework design, etc. Moreover, modification/functionalization of the material structure could optimize the material properties and demonstrate high potential for a selected application. MOF materials exhibit exceptional properties and make these materials widely applicable including in energy storage and heat transformation applications. This review aims to give a broad overview of MOFs and their development as adsorbent materials having the potential for heat transformation applications. We summarize current investigations, developments, and possibilities of metal-organic frameworks (MOFs) especially the tuning of the porosity and hydrophobic/hydrophilic design required for this specific application. These materials applied as adsorbent are promising in the thermal driven adsorption for heat transformation using water as working fluid and related application.

To remove sulfur-containing compounds (SCC) from the diesel fraction 200-360 °C extraction systems have been created based on coordinating organic solvents - dimethylformamide and dimethylsulfoxide and chlorides (CoCl2, CuCl2, CdCl2, MnCl2 and CrCl3) and metal trifluoroacetates (Co (TFA)2, Cu(TFA)2 and Mn(TFA)2). Using PMR spectroscopy the coordination of chloride and metal trifluoroacetate on the oxygen atom in the carbonyl group of DMFA was shown to redistribute electron density in the solvent molecule and to enhance properties of the acceptor center localized on the nitrogen atom. The removal of sulfur-containing compounds from the diesel fraction proceeded under mild conditions - at the temperature of 25 °C and atmospheric pressure. The degree of SCC removal from the diesel fraction in 30 minutes extraction was more than 90%. The interaction of organic solvents with metal salts and sulfur-containing compounds of the diesel fraction was considered within the framework of the concept of "hard and soft acids and bases" (HSAB). The most complete SCC extraction was carried out by "DMFA - Mn(TFA)2, MnCl2 and CrCl3 systems, that was probably connected with the implementation of the" hard base - hard acid "system.

Slow and controlled release systems for drugs, have attracted increasing interest recently. A highly efficient metal-organic gels (MOGs) drug delivery carrier, i.e., MIL-100(Al) gels, has been fabricated by a facile, low cost and environment friendly one-pot process. The unique structure of MIL-100(Al) gels leads to a high loading efficiency (620 mg/g) towards doxorubicin hydrochloride (DOX) as a kind of anticancer drugs. DOX-loaded MOGs exhibited high stability under physiological conditions and sustained release capacity of DOX for up to 3 days (under acidic environments). They further showed sustained drug release behavior and excellent antitumor effects in in vitro experiments on HeLa cells, in contrast with the extremely low biotoxicity of MOGs. Our work provides a promising way for the anticancer therapy, by utilizing this MOGs-based drug delivery system, as an efficient and safe vehicle.

Soy protein isolate (SPI) based materials are abundant, biocompatible, renewable, and biodegradable. In order to improve the tensile strength (TS) of SPI films, we prepared a novel composite film modified with microcrystalline cellulose (MCC) and metal nanoclusters (NCs) in this research. The effects of the modification of MCC on the properties of SPI-Cu NCs and Zn NCs films were investigated. Attenuated total reflectance-Fourier transformed infrared spectroscopy analyses and X-ray diffraction patterns characterized the strong interactions and reduction of the crystalline structure of the composite films. Scanning electron microscope showed the enhanced cross-linked and entangled structure of modified films. Compared with untreated SPI film, the tensile strength of the SPI-MCC-Cu and SPI-MCC-Zn films increased from 2.91 MPa to 13.95 and 6.52 MPa, respectively. Moreover, the results also indicated their favorable water resistance with higher water contact angle. Meanwhile, the composite films exhibited increased initial degradation temperatures, demonstrating their higher thermostability. The results suggested that MCC could effectively improve the performance of SPI-NCs films, which would provide a novel preparation method for environmentally friendly SPI-based films in the applications of packaging materials.

1) Background: Bipolar or manic-depressive disorder is a malign mental disease that frequently faces social stigma. Educational and thinking models are needed to increase people’s awareness and understanding of the disorder. The arts have potential to achieve this goal. 2) Methods: This paper builds on the recent use of heavy metal music as a thinking and education model. It emphasizes the artistic component of heavy metal and its potential to characterize the symptomatology during the episodes of (hypo)mania and depression and the recurrence of these episodes. Heavy metal music has diversified into subgenres that become allegorical to both the symptoms of episodes and the recurrence of bipolar cycles. 3) Results: Examples of songs are given that mirror distinct facets of the disorder. 4) Conclusion: Although the links drawn between art (music) and science (psychiatry) are inherently subjective, such connections might be used to trigger a learning process, facilitate judgment and decision-making, and induce affective reactions and memory formation in the listener. The approach may facilitate collaborative efforts and serve healthcare professionals and educators as a communication tool to aid the public’s comprehension of the disease and an associated social paradox: On one hand, bipolar disorder incurs substantial costs to society. On the other hand, it benefits from the creative artistic and scientific endeavors of bipolar individuals from which cultural and political gains may ensue.

Purpose: This study investigates radiomics efficacy in post-surgical traumatic spinal cord injury (SCI), overcoming MRI limitations from metal artifacts to enhance diagnosis, severity assessment, and lesion characterization for prognosis and therapy guidance. Background: Traumatic spinal cord injury (SCI) causes severe neurological deficits. While MRI allows qualitative injury evaluation, standard imaging alone has limitations for precise SCI diagnosis, severity stratification, and pathology characterization needed to guide prognosis and therapy. Radiomics enables quantitative tissue phenotyping by extracting a high-dimensional set of descriptive texture features from medical images. However, the efficacy of postoperative radiomic quantification in the presence of metal-induced MRI artifacts from spinal instrumentation has yet to be fully explored. Methods: 50 healthy controls and 12 SCI patients post-stabilization surgery underwent 3D multi-spectral MRI. Automated spinal cord segmentation was followed by radiomic feature extraction. Supervised machine learning categorized SCI versus controls, injury severity, and lesion location relative to instrumentation. Results: Radiomics differentiated SCI patients (Matthews correlation coefficient (MCC) 0.97; accuracy 1.0), categorized injury severity (MCC: 0.95; ACC: 0.98) and localized lesions (MCC: 0.85; ACC: 0.90). Combined T1 and T2 features outperformed individual modalities across tasks with gradient boosting models showing highest efficacy. Conclusion: The radiomic framework achieved excellent performance, differentiating SCI from controls and accurately categorizing injury severity. The ability to reliably quantify SCI severity and localization could potentially inform diagnosis, prognosis, and guide therapy. Further research is warranted to validate radiomic SCI biomarkers and explore clinical integration.

Of particular interest is the serendipity of distinctive nonmetallic layered frameworks with the stoichiometry of 1:2 in the binary metallic compounds within inorganic chemistry and materials science. This not only gives rise to the unexpected properties, especially the distinguished superconductivity, as reflected in MgB2, MoB2, NaC2, LaP2 and CeP2, but also strengthens the cognition of the elemental contributions. Although various investigations on the superconducting performances in the alkali, alkaline-earth and rare-earth metal disilicides containing the silicon layers have been reported, the pursuit of superconductors with silicon-planar framework in transition metal disilicides remain unknown up to now. In the present work, crystal structure searches and first-principles calculations were thoroughly conducted in RuSi2 within the pressure range of 0-300 GPa to uncover the novel structures, incredible silicon building block and the amazing properties. The ground orthorhombic Cmca-RuSi2 phase at ambient pressure is a semiconductor with the band gap of 0.485 eV, whose hardness can reach 31.7 GPa. Even more intriguingly, the high-pressure orthorhombic Cmcm-RuSi2 configuration with the fabulous graphene-like silicon-layer, which can be theoretically stabilized with the transformation pressure of 50.97 GPa, can be unexpectedly recovered to ambient pressure. Electron-phonon coupling calculations unravels that it possesses the metallic trait with an estimated Tc value of 1.43 K at 75 GPa, which increases to 10.07 K under ambient pressure. The enhanced Tc stems from the increased density of states at the Fermi level and associated with the coupled vibrations between Ru and the planar Si layer. Meanwhile, the hardness value for Cmcm-RuSi2 is 26.8 GPa under ambient pressure, which further results from the three-dimensional covalent Ru-Si and Si-Si building blocks. The coexistence of superconductivity and high hardness in the Cmcm-RuSi2 configuration under ambient pressure will pave the way for delving into more binary transition-metal silicides and correlated ternary silicides with the profound silicon layers.

Music has been proposed for a long time as a treatment for mental disorders. However, some special types of music or stimulating sounds might induce negative emotions. Herein, 8-week-old male mice were exposed to two specific genres of music, hip-hop (HH) and heavy metal (HM), and construction noise (CN), and a series of behavioral experiments were performed to evaluate the impact of these music or sounds on the emotion of mice. The experiment lasted 1 week in which 8-week-old male mice were used as animal models. We found that long term exposure HM, HH, and CN induced depressive symptoms with a decrease in dopamine receptor 1 and BDNF in the mixture of hippocampus and frontal cortex of mice. Our results have highly addressed that certain special types of sound or music might induce negative emotions and loss of dopaminergic neurons in mice, and it is necessary to intervene in adolescences who are exposed to these music or sounds for a long time.

This study aimed to evaluate the effects of plasma treated metal contaminated water, used for irrigation, on plant growth. Zinc (Zn) is one of the more commonly used metals. It can enter the environment from industrial processes as particles released into the atmosphere or as wastewater discharged into waterways or the ground. Exposure to large amounts of zinc, even for a short time, can seriously affect human health. In this experiment, three different DBD O2 plasma treated zinc contaminated water and a control (tap water) were used, with Arabidopsis thaliana as the model plant. The treatments were: i) Control, ii) Zn water, iii) Zn+O3(30 min), and iv) Zn+O3(60 min). Arabidopsis plant exhibited maximum growth in the Zn+O3(30 min) treatment. All growth parameters, except leaf area, followed this trend: Zn+O3(30 min) > Control > Zn water > Zn+O3(60 min). Gene expression analysis revealed that reduced metal ion stress and controlled oxidation due to active oxygen species contributed to favorable/improved growth of Arabidopsis in the Zn+O3(30 min) treatment. Therefore, 30 minutes of DBD O2 plasma treated zinc contaminated water [Zn+O3(30 min)] can mitigate the adverse effects of excess zinc ions and promote the growth of Arabidopsis plants.

In this study, we demonstrate the direct preparation of dihalo-γ-lactams featuring two distinct halogens from dichloroamides using a novel Atom Exchange Radical Cyclization (AERC) procedure. This method integrates the established Atom Transfer Radical Cyclization with halogen exchange in solution. The technique operates under mild conditions and requires little amounts of metallic copper, serving as both a supplemental activator and reducing agent.

This paper investigates the effects of various process parameters, specifically the substrate temperature, on weld track geometry in Directed Energy Deposition (DED) processes. A specialized experimental setup integrated within a DED machine facilitates controlled thermal conditioning of sample sheets. Through Design of Experiments (DoE) methods, individual weld marks are generated and analysed to assess geometric characteristics. Regression models are constructed to predict machine parameters for desired weld geometry at different substrate temperatures. Validation experiments confirm the accuracy and reliability of the regression models. Results show a consistent trend towards target geometric features across a broad range of substrate temperatures. Despite deviations in measured values, successful fabrication is achieved, demonstrating robust bonding between weld and substrate. Contact angle predictions exhibit precision within a partial temperature range for proper deposition. The developed model offers insights for optimizing DED process parameters to achieve desired weld characteristics, advancing the capabilities and reliability of additive manufacturing technology. Future work aims to refine the regression model and explore additional mathematical relationships for enhanced accuracy. An implication of this work is the potential to vary the local mechanical properties of parts by controlling the temperature profile while maintaining consistent geometric characteristics. By manipulating the substrate temperature, it may be possible to tailor the microstructure and mechanical properties of fabricated components in the future to meet specific requirements in different regions of the part.

Asymmetric lithium salts, such as Lithium (difluoromethanesulfonyl)(trifluoromethanesulfonyl)imide (LiDFTFSI), have been demonstrated to surpass traditional symmetric lithium salts with improved Li+ conductivity and the capacity to generate stable solid electrolyte interphase (SEI) while maintaining compatibility with aluminum (Al0) current collector. However, the intrinsic reductive mechanism through which LiDFTFSI influences battery performance remains unclear and under debate. Herein, the detailed SEI reactions of LiDFTFSI-based electrolytes were investigated by combining density functional theory and molecular dynamics, aiming to clarify the formation process and atomic structure of SEI. Our results show that asymmetric DFTFSI– weakens the interaction between carbonate solvents and Li+, and substantially alter the solvation structure, exhibiting a well-balanced coordination capacity to bis(trifluoromethanesulfonyl)imide (TFSI–). Nanoseconds hybrid molecular dynamics simulation further reveals that the preferential decomposition of LiDFTFSI produces sufficient LiF and Li2O to facilitate a robust SEI. Moreover, the abundant F– generated from LiDFTFSI decomposition accumulates on the Al surface and subsequently combines with Al3+ from the current collector to form AlF3, potentially inhibiting corrosion of the current collector. Overall, these findings elucidate how LiDFTFSI regulates the solvation sheath and SEI structure, advancing the development of high-performance electrolytes compatible with current collector.

In the present work, a predictive modelling and optimization with the adaptive network based fuzzy inference system(ANFIS) modelling of mechanical properties of laser-coated NB/SiC/Ni welds was studied based on Taguchi design by laser cladding. An ANFIS model based on a Sugeno type fuzzy inference system was developed for predicting the hardness properties of SiC/BN/Ni welds by laser cladding with experimental data required for network training and prediction. Based on analysis of variance, three important factors were taken as inputs for the fuzzy logic inferences, while the hardness properties was taken as the output of the ANFIS. The microstructure of welds were analysed using scanning electron microscopy with an energy dispersive X-Ray spectrometer. Highly developed leaf-like dendrites and eutectic crystals were found in some areas of the melting zone for the BN/SiC/Ni weld, which was significantly hardened. The ANFIS model based on Taguchi's design provides a better pattern of response because the predicted and experimental values were highly similar. As a result, a satisfactory result was achieved between the predicted and experimental values of hardness in laser-coated NB/SiC/Ni welds, whereby the success and validity of the method was verified.

The field of fluorescence sensing, leveraging various supramolecular self-assembled architectures constructed from macrocyclic pillar[n]arenes, has seen significant advancement in recent decades. This review comprehensively discusses, for the first time, the recent innovations in the synthesis and self-assembly of pillar[n]arene-based supramolecular architectures (PSAs) containing metal coordination sites, along with their practical applications and prospects in fluorescence sensing. Integrating hydrophobic and electron-rich cavities of pillar[n]arenes into these supramolecular structures endow the entire system with self-assembly behavior and stimulus responsiveness. Employing the host–guest interaction strategy coupled with complementary coordination forces, PSAs exhibiting both intelligent and controllable properties are successfully constructed. This provides a broad horizon for advancing fluorescence sensors capable of detecting environmental pollutants. This review aims to establish a solid foundation for the future development of fluorescence sensing applications utilizing PSAs. Additionally, current challenges and future perspectives in this field are discussed.

3D printing is a non-traditional additive manufacturing process. It is different from the traditional subtractive manufacturing process. It offers exceptional rapid prototyping capabilities and results that traditional subtractive manufacturing methods cannot attain, especially in applications involving curved or intricately shaped components. Despite its advantages, metal 3D printing will face porosity, warpage, and surface roughness issues. These issues will affect the future practical application of the parts indirectly, for example, the structural strength and the parts assembly ca-pability. Therefore, this study compares the qualities of the warpage, weight, and surface rough-ness after milling and grinding processes under the same materials (316L stainless steel) between general rolled steel and 3D additive steel. Experimental results show that 3D printing parts are approximately 13% to 14% lighter than the general rolled steel. The surface roughness performance of 3D printing steel is better than general rolled steel under the same material after milling or grinding processing. The hardness of the 3D printing steel is better than that of the gen-eral rolled steel. The research verifies that 3D additive manufacturing can use surface processing to optimize surface performance and achieve the functions of lightness and hardness.

Yellow nanorod Mg-MOF-74 was obtained by solvothermal synthesis method. XRD、N2 adsorption-desorption isotherms、SEM and TGA results suggest that the particle size of Mg-MOF-74 reaches 400 nm after the introduction of sodium acetate in the precursor of Mg-MOF-74. Besides, the morphology of Mg-MOF-74 was changed from cauliflower to rod particles. At the same time, the BET specific surface area and pore volume of Mg-MOF-74 were also increased a lot. Then the CO2 dynamic adsorption capacity of Mg-MOF-74 was measured by self-made fix bed under 30 ℃、0.1 bar CO2 partial pressure. The results show that the CO2 adsorption capacity of Mg-MOF-74-N2 reaches 3.67 mmol/g and its CO2 adsorption capacity remains unchanged after 10 times CO2 adsorption-desorption cycles.

Crystalline silicon nanomembrane (Si NM) is promising in wearable and implantable bioelectronics due to its electrical and mechanical performances. However, the current explorations are not enough to firmly bridge ultrathin encapsulation strategies with high performance crystalline Si NM based transistors. In this work, we utilized Al2O3/alucone as the ultrathin encapsulation strategies aim to thoroughly investigate the effect of gate dielectric surface area on the electrical performance of crystalline Si NM based metal-oxide-semiconductor capacitors (MOSCAPs). The comparative analysis was implemented on the three types of diameters (Ø) MOSCAPs with and without Al2O3/alucone encapsulation under planar and concave/convex bending conditions. Benefited from the Al2O3/alucone ultrathin encapsulations, the stability of gate leakage current density, and interfacial characteristics were maintained and improved under mechanical bending deformations for MOSCAPs with predefined Ø of 160, 240, and 320 μm compared to the bare MOSCAPs. Combined with the Ø-related mechanical analysis on the maximum strain in the critical layers and the practical measurements, the encapsulated MOSCAPs with Ø 160 μm showed the most stable electro-mechanical performances. The variations for encapsulated MOSCAPs with three types of Ø emerged in the oxide layer and the interface at dielectric/Si NM that were carefully evaluated according to the bending deformations. These findings are significant for leveraging the practical applications in the ultrathin encapsulation strategies for reliable operations of crystalline Si NM based integrated circuits (ICs).

Deep eutectic solvents are a mixture of two or more components, that at a particular composition become liquids at room temperature. When the compounds that constitute the DES are primary metabolites, namely, amino acids, organic acids, sugars, or choline derivatives, the DES are so called natural deep eutectic solvents (NADES). NADES fully represent green chemistry principles. These solvents are highly welcome, as they are obtained from renewable resources, and gratifyingly biodegradable and biocompatible. They are an alternative to room temperature ionic liquids (RTILs). From the pharmaceutical industry point of view, they are highly desirable, but unfortunately have been rarely used despite their enormous potential. In this review, we will look at their impact on the asymmetric catalytic synthesis of key target molecules, via metal-based catalysis, biocatalysis and organocatalysis. In many cases the NADES that have been used are chiral and can even promote enantioselective reactions, this crucial and very exciting aspect will also be discussed and analysed.

Urban gardens have important social, environmental and economic roles in big cities, contributing to their sustainability. However, food production in urban gardens may be compromised due to soil pollution that resulted from decades of industrial non-regulated environmental activity and mobile transport. In this study, 12 soils from the urban agricultural area of Rome (Italy) were analyzed for the metals Be, Ba, Pb, Co, Ni, V, Zn, Hg, Cd, As, Cu, and Cr. All but one of the soils under analysis were characterized by at least one metal concentration above the threshold limit defined by the Italian Legislative Decree 152/2006 (ILD) for agricultural soils. Multivariate analysis showed that the soils could be classified into five clusters: clusters I and II had relatively lower mean metal concentrations; clusters III, IV, and V had relatively higher mean metal concentrations with several metal concentrations above the threshold proposed by ILD. Three factors contributing to the variability of the metal’s concentration in the soils under investigation were identified: geological factor, related with metals As, Ba, Be, and V; anthropogenic factor, related with Pb and Cu; and, a mixed factor related with Co, Cr, Ni, and Zn. High metal content may limit the utilization of urban soils as urban gardens for food production.

Metal-Organic Frameworks (MOFs) have been observed to exclusively eliminate dyes confined within their respective pores. In this investigation, the synthesis of a breathable MOF structure, MIL-88B(Fe), was pursued with the objective of circumventing restrictions on pore size to en-hance its adsorption capabilities. The synthesis of MIL-88B(Fe) was carried out via the assisted solvothermal method at 373 K using inexpensive yet environmentally benign FeCl3.6H2O, 1,4-benzenedicarboxylic acid and DMF as metal precursor, as linker and solvent, respectively. Furthermore, MOF was subjected to extensive analytical characterization using XRD, FT-IR spectroscopy, N2 gas sorption, TGA, and SEM. The experimental data showed that the utilization of MIL-88B(Fe) with a dose level of 5 mg for 180 mins at pH of 9 led to the highest levels of ad-sorption for both dyes with 162.82 mg g-1 for Methylene Blue (MB) and 144.65 mg g-1 for Rho-damine B (RhB), as a result of contrast molecular size between each dye. The Langmuir and Freundlich models demonstrate a correlation with isotherms, while the thermodynamic analysis demonstrated that MIL-88B(Fe) exhibits distinct endothermic and breathable properties. The ef-ficacy of MIL-88B(Fe) adsorbent for MB and RhB in aqueous solutions indicated exceptional performance, stability, and noteworthy reusability performance.

This study conducts a comprehensive analysis of the presence of heavy metals, including zinc (Zn), lead (Pb), copper (Cu), chromium (Cr), and arsenic (As), in the dust found inside educational buildings and the top layer of soil in different areas of Vilnius. The study focuses on the analysis of topsoil samples gathered between 2011 and 2023, with a specific emphasis on dust samples obtained from 24 schools in 2022. The research reveals significant variations in the concentrations of heavy metals, providing a clear understanding of the complex relationship between sources of urban pollution, environmental processes, and the correlation between soil and dust contamination by heavy metals. Indoor dust in schools shows unique contamination patterns in contrast to topsoil, suggesting distinctive sources of indoor pollution, while there are some general similarities. This finding emphasizes similarities and distinctions between soil and dust in educational environments. The study utilizes advanced statistical methods such as Pearson correlation, Principal Component Analysis (PCA), and hierarchical clustering to examine the distribution and characteristics of these metals. This study distinguishes itself by examining indoor dust in educational facilities and topsoil in Vilnius, providing crucial insights into the relationship between these two environmental matrices.

Transportation is the primary consumer of oil, accounting for a significant portion of global energy consumption (34%) and CO2 emissions (40%). Electrifying road transportation is crucial to mitigate the effects of global warming. The abundant potential of renewable energy sources like solar and wind is hindered by their intermittent nature and incongruity with peak energy demands. This calls for the development of sophisticated energy storage solutions. Metal-air batteries (MABs), emerging as viable alternatives to lithium-ion batteries (LIBs), have attracted considerable attention due to their promising applications in the transportation sector. Despite substantial progress in MAB development over the past two decades, overcoming critical challenges such as electrolyte decomposition, carbon cathode degradation, anodic dendrite growth, and air impurities remains essential for their commercial viability. This mini-review provides a comprehensive overview of MAB fundamentals and the challenges associated with their development. The insights presented in this review serve to illuminate the current landscape and future prospects of MABs in the transportation sector.

The paper presents the numerical and experimental results of research aimed at determining the influence of hardness in the range of 50-90 Shore A of layered tools made of elastomeric materials on the possibility of forming Inconel 625 nickel-based alloy sheets. A stamping die made of 90MnCrV8 steel (hardness 60HRC) was designed for forming embosses in drawpieces, ensuring various stress states on the cross-section of the formed element. The principle of operating the stamping die was based on the Guerin method. Finite element-based numerical modelling of the forming process for various configurations of polyurethane inserts was also carried out. The drawpieces obtained by sheet forming were subjected to geometry tests using optical 3D scanning. The results confirm that in the case of forming difficult-to-deform Inconel 625 Ni-based alloy sheets, the hardness of the polyurethane inserts significantly affects the geometric quality of the obtained drawpieces. The assumptions made in numerical simulations were verified in experimental studies. Based on the test results, it was concluded that the selection of polyurethane hardness should be determined by the shape of the formed element. Significant non-uniform sheet metal deformation was also found, which may pose a problem in the process of designing forming tools and technology of plastic forming of Inconel 625 Ni-based alloy sheets.

This review article deals with the pathways of cellular and global molybdate distribution in plants, especially with a full overview for the model plant Arabidopsis thaliana. In its oxidized state as bioavailable molybdate, molybdenum can be absorbed from the environment. Especially in higher plants, molybdenum is indispensable as part of the molybdenum cofactor (Moco), which is responsible for functionality as a prosthetic group in a variety of essential enzymes like nitrate reductase and sulfite oxidase. Therefore, plants need mechanisms for molybdate import and transport within the organism, which is accomplished via high-affinity molybdate transporter (MOT) localized in different cells and membranes. Two different MOT-families were identified. Especially legumes like Glycine max or Medicago truncatula have an increased numbers of MOT1-family members for supplying their symbionts with molybdate for nitrogenase activity. In Arabidopsis thaliana especially, the complete way of molybdate through the plant is traceable. Not only the uptake from soil by MOT1.1 and its distribution to leaves, flowers and seeds by MOT2-family members was identified, but also inside the cell the transport trough the cytoplasm and the vacuolar storage mechanisms depending on glutathione were described. Finally, supplying the Moco biosynthesis complex by MOT1.2 and MOT2.1 was demonstrated.

Platinum group metals (PGMs) high-grade ore tonnage from Merensky reef keeps on depreciating forcing the metallurgical industry to explore beneficiating PGMs from upper group 2 (UG2) ore which has up to 60% content of chromite and from secondary sources. The PGMs are naturally associated with base metal sulphides and the efficacy of the PGMs extraction processes is dependent on the processing of PGMs-bearing base metal sulphides. These processes include concentrating PGMs-bearing base metal sulphides through flotation, oxidation, etc. prior the metal extraction processes. The evolving mineralogy of PGMs ores has necessitated the use of multiple reagents to enhance the efficiency of the concentration process. This has led to an increased amount of inor-ganic chemicals disposal to the environment and the processing of PGMs to be less economic. Bio-technology has been investigated as a potential low cost, ecologically safe substitute for many current minerals processing methods. The metabolites produced by microorganisms have been used for many years with great success in the leaching and flotation of metals from medium and low-grade sulphide minerals. The possible application of microorganism mainly Acidithiobacillus ferrooxidans (A. ferrooxidans) in the metallurgical processing of PGMs-bearing base metal sulphides is systematically reviewed in this paper. The main emphasis is on the use of A. ferrooxidans in bio-oxidation and bioleaching, as well as their potential to substitute inorganic reagents in the flo-tation of PGMs-bearing base metal sulphides from primary and secondary sources

Date palm trees generate large amounts of various types of waste, including leaf sheath fibers which can be used as a low-cost, precursor for production of biochar including activated carbon (AC) that can be employed for adsorption of contaminants. In the current study, activated carbon was made from leaf sheath fibers of date palm (LSDPFAC) by use of chemical activation with K2CO3, combined with microwave irradiation, characterized and evaluated for its adsorptive capacity of lead ions (Pb2+). The Brunauer–Emmett–Teller (BET) surface area, Langmuir surface area, total pore volume and average pore diameter of LSDPFAC were 560.20 m2/g, 744.31 m2/g, 0.29 cm3/g and 2.47 nm respectively. When the initial concentrations of Pb2+ were increased from 1 to 10 mg/L, Pb2+ adsorption increased from 0.97 to 8.76 mg/g, dry mass (dm) while the percent of Pb2+ removed decreased from 96.70 to 87.60%. The greatest removal of Pb2+ occurred at pH 13 with adsorption capacity of 9.15 mg/g, dm. Results of isotherm and kinetic studies demonstrated that adsorption of Pb2+ onto LSDPFAC was best described by the Freundlich isotherm and pseudo-second order (PSO) models. Langmuir monolayer adsorption capacity, Qm was 14.10 mg/g. Thermodynamic parameters of H°, S°, G° and Ea were 6.39 kJ/mol, 0.12 kJ/mol.K, -31.28 kJ/mol and 15.90 kJ/mol, respectively, which demonstrated that adsorption of Pb2+ by LSDPFAC was endothermic, spontaneous and governed by physisorption.

Microwave absorbers with lightweight, good stability and high efficiency have attracted much attention for their applications in many contemporary fields. In this work, the 3D porous (Ni@NO-C)n/NO-C composite absorber was prepared by a wet chemistry method with Ni chains and melamine as precursors, in which NO-C (N,O-doped carbon) encapsulated Ni particles are homogenously dispersed in the 3D porous networks of NO-C in the form of (Ni@NO-C)n chains. The special microstructure of the as-prepared material is proved to be benefit for the improvement of its microwave adsorption performance. The as-synthesized (Ni@NO-C)n/NO-C composite ab-sorber exhibited an effective absorption bandwidth of 4.1 GHz and an extremely large reflection loss of -72.3 dB. The excellent microwave absorbing performances can be ascribed to the coopera-tive consequence of dielectric loss and magnetic loss along with the balance between attenuation capability and impedance match.

Due to increasing concerns about global warming and energy crisis, intensive efforts have been made to explore renewable and clean energy sources. Single-atom metals and two-dimensional (2D) nanomaterials have attracted extensive attention in the fields of energy and environment because of their unique electronic structures and excellent properties. In this review, we sum-marize the state-of-art progress on the single-atom metal supported at 2D MoS2 (single-atom metal/2D MoS2) for electrochemical CO2 reduction and water splitting. First, we introduce the advantages of single-atom metal/2D MoS2 catalysts in the fields of electrocatalytic CO2 reduction and water splitting, followed by the strategies for improving electrocatalytic performances of single-atom metal/2D MoS2 hybrid nanomaterials and the typical preparation methods. Further, we discuss the important applications of the nanocomposites in electrocatalytic CO2 reduction and water splitting via some typical examples, particularly focusing on their synthesis routes, modification approaches, and physiochemical mechanisms for improving their electrocatalytic performances. Finally, our perspectives on the key challenges and future directions of exploring high-performance metal single-atom catalysts are presented based on recent achievements in the development of single-atom metal/2D MoS2 hybrid nanomaterials.

Abstract Aims: In recent years, electro kinetic (EK) remediation has become more popular as a novel method for removing chromium contamination from soil. This approach, however, is ineffective since it uses both cationic and anionic forms of chromium. In this work, a membrane –based technique was employed to increase the efficiency of the electro kinetic removal of chromium. Methods: Chromium removal from polluted sludge was studied in four bench-scale experiments, two of which used distilled water (EK-1, EK2 & Membrane) and two of which used acetic acid as a catholyte (EK-3, EK4 &Membrane). Results: The pH, total chromium, and fractionation of chromium in the sludge were measured after remediation. In the EK-1, EK-2 & Membrane and EK-3, EK-4 & Membrane trials, the average removal efficiency of total chromium was 47.6%, 58.6%, and 74.4%, 79.6%, respectively. Conclusion: In contrast to the electro kinetic remediation strategy, which left approximately 80% of the sludge neutral or alkaline after treatment, the use of the membrane created acidic soil conditions throughout the sludge. For example, the high field intensity used in the membrane tests may have helped to facilitate chromium desorption, dissolution and separation from the sludge, as well as enhance chromium mobility. The findings show that the membrane can improve the effectiveness of chromium removal from sludge when utilized in the EK remediation process.

Nanostructured transition metal nitrides (TMNs) have been considered a promising substitute for precious metal catalysts toward ORR due to their multi-electron orbitals, metallic properties, and low cost. To design TMNs catalysts with high catalytic activity toward ORR, the intrinsic features of the influencing factor on the catalytic activity toward ORR of nanostructured TMNs need to be investigated. In the paper, titanium nitride (TiN), zirconium nitride (ZrN), and hafnium nitride (HfN) nanoparticles (NPs) are high-efficiency and one-step synthesized by the direct current arc plasma. TiN, ZrN, and HfN NPs with an oxidation layer are applied as the catalysts of hybrid sodium-air batteries (HSABs). The effect of composition and structure attributes of TMNs on ORR catalysis is defined as follows. (ⅰ) Composition effect. With the increase of the oxygen content, the catalytic ORR capability of TMNs decreases progressively due to the reduction of oxygen adsorption capacity; (ⅱ) Structure effect. The redistribution of the density of states (DOS) of ZrN indicates higher ORR activity than TiN and HfN. HSABs with ZrN exhibit an excellent cyclic stability up to 137 cycles (about 140 h), an outstanding rate performance, and a specific capacity of 2817 mAh·g−1 at 1.0 mA·cm−2.

In interceptive treatments in which impacted teeth (incisor or first permanent molar) should be included into the dental arch, the main clinical problem is the provision of an anchorage area and a suitable appliance. The use of laser sintered metal orthodontic grids, designed and printed digitally, has expanded the boundaries of orthodontic treatment, especially in its interceptive phase. Our aim is to describe a digital model for providing anchorage during orthodontic-surgical traction of impacted teeth in the mixed dentition period. We present the treatment of three clinical cases with digitally projected and printed metal grids used for anchorage. In the described clinical cases, individually designed anchorage systems were used. They were created through design software and after that the metal grids were printed. The devices are placed in the oral area and don’t disturb the aesthetics of the patient in any way. The advantages of individual designed metal support grids allow to accommodate the features of relief of the hard palate and alveolar bone. This makes the grids comfortable for the patient and rigid enough to perform orthodontic tractions at the same time. The printed additional grids are applicable in mixed dentition and in complicated clinical cases in permanent dentition. Their individuality allows segmental treatments or treatments in cases requiring additional anchorage further from the active force.

Oxygen evolution reaction is a momentous part of electrochemical energy storage and conversion devices such as rechargeable metal-air batteries. It is particularly urgent to develop low-cost and efficient electrocatalysts for oxygen evolution reactions. As a potential substitute for noble metal electrocatalysts, transition metal selenides are still challenging in improving the activity of oxygen evolution reaction and the research of reaction intermediates. In this study, a simple one-step solvothermal method was used to prepare a polymetallic compound carbon matrix composite (Co9Se8/Ni3Se4/Fe3O4@C) with a multilayered nanosheets structure. It exhibited good OER activity in an alkaline electrolyte solution with an overpotential of 268 mV at 10 mA/cm2 in an alkaline medium. Besides, this catalyst also showed excellent performance in the 24 hours stability test. The composite presents a multi-layer sheet structure, which effectively improves the contact between the active site and the electrolyte. The selenide formed by Ni and Co has a synergistic effect, Fe3O4 and Co9Se8 form a heterojunction structure, which can effectively improve the reaction activity by initiating the electronic coupling effect through the interface modification. In addition, carbon quantum dots have rich heteroatoms and electron transferability, which improves the electrochemical properties of the composites. This work provides a new strategy for the preparation of highly efficient OER electrocatalysts utilizing the multimetal synergistic effect.

The reckless use of non-replenishable fuels by the growing population for energy and the resultant incessant emission of hazardous gases and waste products into the atmosphere insisted scientists to fabricate materials capable of managing these global threats at once. In recent studies, photo-catalysis employed focus on utilizing renewable solar energy to initiate chemical processes with the aid of semiconductors and highly selective catalysts. A wide range of nanoparticles have showcased promising photocatalytic properties. Ultrasmall metal nanoclusters (MNCs) with sizes below 2 nm, stabilized by ligands shows discrete energy levels, exhibits unique optoelectronic properties which are vital to photocatalysis. In this review, we intend to compile information on varying photocatalytic efficiency of metal NCs with respect to changes in their properties. Review discusses about the photocatalytic activity of atomically precise ligand-protected MNCs and its hybrids in the domain of in energy conversion processes like photodegradation of dyes, Oxygen Evolution Reaction (ORR), Hydrogen Evolution Reaction (HER) and CO2 Reduction Reaction (CO2RR), and photosensitizer in solar cell.

Metal-organic frameworks (MOFs) are investigated for the oxygen evolution reaction (OER) due to their structure diversity, high specific surface area, adjustable pore size and abundant active sites. However, the poor conductivity of most MOFs restricts this application. Herein, through a facile one-step solvothermal method, the Ni-based pillared metal-organic framework [Ni2(BDC)2DABCO] (BDC = 1,4-benzenedicarboxylate, DABCO = 1,4-diazabicyclo[2.2.2]octane), its bimetallic nickel-iron form [Ni(Fe)(BDC)2DABCO] and their modified Ketjenblack (mKB) composites were synthesized and tested towards OER in an alkaline medium (KOH 1 mol L–1). A synergistic effect of the bimetallic nickel-iron MOF and the conductive mKB additive enhance the catalytic activity of the MOF/mKB composites. All MOF/mKB composite samples (7, 14, 22, 34 wt.% mKB) indicated much higher OER performances than the MOFs and mKB alone. The Ni-MOF/mKB14 composite (14 wt. % of mKB) demonstrated an overpotential of 294 mV at a current density of 10 mA cm–2 and Tafel slope of 32 mV dec–1, which is comparable with commercial RuO2 commonly used as a benchmark material for OER. The catalytic performance of Ni(Fe)MOF/mKB14 (0.57 wt% Fe) was improved further to an overpotential of 279 mV at a current density of 10 mA cm–2. The low Tafel slope of 25 mV dec–1 as well as a low reaction resistance due to electrochemical impedance spectroscopy (EIS) measurement confirm the excellent OER performance of the Ni(Fe)MOF/mKB14 composite. For practical applications, the Ni(Fe)MOF/mKB14 electrocatalyst was impregnated into commercial nickel foam (NF), where overpotentials of 247 and 291 mV at current densities of 10 and 50 mA cm–2, respectively, were realized. The activity was maintained for 30 h at the applied current density of 50 mA cm–2. The electrocatalytic system consisting of earth-abundant Ni and Fe metals only would be attractive for the development of efficient, practical and economical energy conversion materials for efficient OER activity.

The microstructure evolution, superplasticity, and room temperature mechanical properties of Ti-4%Al-1%V-3%Mo alloys modified with 0.01-2 wt.% boron were investigated. Increasing the boron content from 0 to 0.1 wt.% effectively refined prior β-grains, reducing a mean grain size from ~700 µm to ~210 µm. Whiskers of the TiB phase with a size in a range of 0.7-2.9 µm were observed after solidification and thermomechanical processing. Alloys with 0.01-0.1 wt.% boron exhibited similar superplastic elongations and strain rate sensitivity coefficient m of 0.4-0.5 at a strain rate of 1×10-3 s-1 and the elongation to failure decreased from 1000% at 875°С to 400-500% at 700°С. Along with this, the minor boron addition effectively decreased flow stress values, especially at 775 °C, that was explained by the acceleration of the recrystallization and globularization of the microstructure at the initial stage of deformation. Recrystallization-induced decrease in yield strength from 770 MPa to 680 MPa was observed with an increase in boron content from 0 to 0.1 wt.%. Heat treatment increased post-forming strength characteristics for the alloys with 0.01-0.1 wt.% boron by 90–140 MPa without ductility reduction. Alloys with 1-2 wt.% B demonstrated the opposite behavior. The grain refinement effect was not revealed, and prior β grain sizes were ~670-750 µm after solidification. Thermomechanical processing promoted the fragmentation of boride whiskers and the formation of near-spherical particles with a size of ~1 μm for the alloy with a eutectic concentration of 2 wt.% B. A high fraction of borides, ~5-11%, in the alloys with 1-2 wt.% B deteriorated the superplastic properties and drastically decreased ductility at room temperature. The alloy with 2 wt.% B demonstrated non-superplastic behavior and a low level of mechanical properties, meanwhile, the alloy with 1% boron exhibited high-temperature superplasticity at 875 °C with elongation of ~500%, and yield strength of 830 MPa, ultimate tensile strength of 1020 MPa at a room temperature after 100% of superplastic deformation.

In spite of large-scale investigations of homogeneous single-site metallocene catalysts and systems based on them, the problem of controlling their activity, chemo- and stereoselectivity with the aim of developing efficient methods for the preparation of practically useful products of alkenes transformation, such as dimers, oligomers, and polymers, still remains topical. Here we studied catalytic activity of differently structured zirconocenes (10 examples of cyclopentadienyl and indenyl complexes) and co-catalysts activating the system, namely HAlBui2, MMAO-12 or (Ph3C)[B(C6F5)4] at low activator/Zr ratios in 1-hexene oligomerization reaction. The influence of catalyst structure and system composition on alkene conversion, type of products formed and reaction stereoselectivity was investigated. The composition of hydride intermediates forming in the systems L2ZrCl2 (L2= ansa-Me2CCp2)-HAlBui2-activator was studied by NMR and the participation of biszirconium hydride complex as the precursor of catalytically active sites of the alkene dimerization reaction was shown.