The aim of this study is to investigate transient dynamic flow characteristics of the fluid flow through 5-way electric coolant valve (PCCV : Penta-Control Coolant Valve). To achieve this goal, the present paper attempts the three-dimensional dynamic simulation of the fluid flow through the valve using a commercial CFD solver with moving mesh technique to consider flow inertia and dynamic flow in the opening and closing stages of the ball valve rotating motion. Firstly, dynamic flow characteristics and the thermal mixing inside the PCCV ball valve during the opening and closing stage was analyzed. It is found that the discrepancies between dynamic and steady state simulation is remarkable when fluxes with different levels of enthalpy and momentum flow into the PCCV leads to strong flow interference and flow inertia, while the discrepancies are relatively small at low rotation speed and weak flow interference. Then, the effect of dynamic flow characteristics of the valve on dynamic thermal mixing characteristics at two different ball valve rotational speeds and rotational directions were investigated. It was found that the dynamic flow and thermal mixing characteristics inside the PCCV are greatly affected by the rotation speed, rotation direction, and degree of flow interference between fluxes. It is helpful for the design of the better coolant control strategies and the improvement of the FCEV thermal management system.

Coal gasification with carbon dioxide is a process for generating clean gaseous fuels and relieving greenhouse effect. Zhundong coal has high alkali and alkali earth metals (AAEMs) content, medium volatile and low ash in nature. Isothermal CO₂ gasification of char derived from Zhundong coal (R-char) and char from acid washing R-char (AR-char) are performed in thermo-gravimetric analyzer (TGA). The effect of AAEMs is investigated on the gasification behavior in the range of temperatures 1073 K to 1273 K. The carbon conversion increases rapidly with increasing reaction temperature and CO₂ concentration. R-char has high gasification rate and carbon conversion compared with AR-char. The accuracy of the free-model approach for calculating activation energy at different conversions is validated by compared with different kinetic models (volume reaction model, distributed activation energy model). Moreover, R-char gasification with CO₂ shows a compensation effect as the Arrhenius parameters (EA and k0) increase or decrease simultaneously.

Three kinds of inorganic alkali are introduced into tetraethylenepentamine (TPEA) and polyethyleneimine (PEI) modified MCM-41 as the CO2 adsorbents. FT-IR and TGA are used to characterize the surface groups and the thermal stability of adsorbents. Chemical titration method is used to measure the alkali amounts of adsorbents. Thermo-gravimetric analysis with 10%CO2/N2 as the simulated flue gas is used to test the CO2 adsorption performance of adsorbents. The results show that all three kinds of inorganic alkali containing adsorbents exhibit promoted CO2 adsorption capability than traditional TPEA and PEI modified samples. Ca(OH)2 and PEI modified samples exhibit the highest adsorption capacity and stable regeneration property. The introduction of inorganic alkali changes the chemical adsorption mechanism between CO2 and increases the effective alkali amounts due to its hydroxyl groups. The CO2 adsorption capacities have a linear dependence relation with the alkali amounts of adsorbents, indicating that alkali amount is a critical factor for novel adsorbents exploring.

The object of study in the article is the auxiliary variable-frequency electric drive onboard of an AC electric locomotive, and more precisely, the structure and parameters of the control system of the active corrector of power factor (ACPF), which is part of the electric drive, as a unit that ensures electromagnetic compatibility of the electric drive with other equipment on board the electric locomotive and catenary and its energy efficiency. The topic of the article's research is the substantiation of the structure of the ACPF control system, the choice of types (transfer functions) of controllers and the calculation of their parameters. The research method chosen was the calculation of the transfer functions of the controllers of the cascaded loops control system, followed by computer simulation using the OrCAD software. The results of simulating a cascaded two loops control system of an ACPF with different types of controllers are presented and analytically compared. It is concluded that it is advisable to use a cascaded two loops control system, containing a voltage control loop and a current control loop. The best results show the simulation when using an aperiodic current controller (A-controller) and a proportional-integral voltage controller (PI-controller). The data obtained serve as the basis for further improvement of the operation of the ACPF by enhancing and optimizing the settings, structure and algorithms of the control system, which, with the selected hardware of power converter unit, will allow the ACPF to perform its functions with a high degree of reliability in an entire range of disturbing and control influences.

Toll plaza optimization is essential for improving traffic flow and easing congestion on road networks. This study aims to suggest and assess potential optimization solutions for the Peshawar toll plaza, considering variables like traffic volume, toll-collecting effectiveness, and customer facilitation. Different resources are used for data collection, like the National Highway Authority of Pakistan. Physical data is collected from the established Toll Plaza of Peshawar, along with the development of each line. The goal of this study is to suggest and assess potential optimization solutions for the Peshawar toll plaza, considering variables like traffic volume, toll-collecting effectiveness, and customer happiness. The analysis of present traffic patterns, the detection of bottlenecks, and the creation of plans to ease congestion and enhance overall traffic flow are all part of the optimization process. The approaches used in this study include data analysis, simulation, and traffic modeling. PTV VISSIM is software for transportation planning, design, and analysis. The simulations consider various conditions, such as variable traffic volumes, toll collection methods, and lane configurations. When comparing the different optimization strategies, performance indicators like trip time, latency, and queue length are utilized to determine which approach is practical. Waiting time Vs. Existing each lane, etc, is explained. In the end, comparing queue lengths and throughput across different lane scenarios shows that maximizing throughput with existing lanes yields up to 45% improvement with E-tag lanes, 40% with existing E-tag lanes, 38% with E-tag plus additional toll and cash lanes, 32% with three cash lanes, and 28% with two E-tag lanes. Failure to regularly monitor and adjust the existing lane pattern scenario based on traffic patterns can lead to queues being 20% longer. Without proactive evaluation and optimization, there is a potential 63% opportunity for queue length improvement

Interleukin-12 (IL-12) is considered to be a promising cytokine for enhancing anti-tumor immune response. However, recombinant IL-12 had significant toxicity and limited efficacy in early clinical trials. Recently, many strategies for delivering IL-12 to tumor tissues have been developed, such as modifying IL-12, utilizing viral vectors, non-viral vectors and cellular vectors. Previous studies have found that IL-12 fusion with extracellular matrix proteins, collagen and immune factors is a way to enhance its therapeutic potential. In addition, studies have demonstrated that viral vectors are a good platform, and a variety of viruses such as oncolytic viruses, adenoviruses and poxviruses have been used to deliver IL-12, and testing has been conducted in various cancer models. Local expression of IL-12 in tumors based on viral delivery avoids systemic toxicity while inducing effective anti-tumor immunity and acting synergistically with other therapies without compromising safety. Also, lipid nanoparticles are currently considered to be the most mature drug delivery system. Moreover, cells are also considered to be drug carriers because they can effectively deliver therapeutic substances to tumors. In this article, we will systematically discuss the antitumor effects of IL-12 on its own or in combination with other therapies based on different delivery strategies.

Next-generation sequencing(NGS) for HIV drug resistance(DR) testing has an increasing number of applications for detection of Low-abundance drug resistant variants(LA-DRVs) as its features of quasispecies. However there is less information on detection performance in DR detection with NGS.To determine the feasibility of NGS technology in LA-DRVs detection for HIV-1 pre-treated patients.In this study,80 pre-treated patients’ samples accepted both NGS and Sanger sequencing(SS) in HIV-1 drug resistance testing. The results show that NGS presents higher sensitivity in mutation sites discovery at 5% threshold. NGS shows a satisfactory consistency comparing with SS in both protease inhibitors(PIs) and Integrase inhibitor(INSTIs), more than 90%. But worse consistency in Nucleotide reverse transcriptase inhibitors(NRTIs), only ranging from 61.25%-87.50%. The consistency of Non-nucleotide reverse transcriptase inhibitors(NNRTIs) between NGS and SS was around 85%. NGS shows the highest sensitivity of 91.3% at 5% threshold. The application of NGS technology in HIV-1 genotype resistance detection in different populations infected with HIV needs more documents and to be confirm further.

Reliability assessment is an important component and tool used for process plants since the facility consists of many loops and instruments attached and operates based on each other availability, thus it requires a statistical method to visualize the reliability. The paper focuses on reliability assessment and prediction based on available statistical models such as normal, log-normal, exponential, and Weibull distribution. This paper also visualizes, which model fits best for assessment and prediction and also considers failure modes caused during a simulation mode process control operation. A simulation model is designed in this paper to observe the failure of the control valve causing stiction to visualize the failure modes and predict the best-fit model for reliability assessment.

With the development of higher voltage power grid, the high and low voltage parallel loops are emerging, which lead to energy losses, even threaten the security and stability of power system. The multi-infeed HVDC configurations widely appearing in AC/DC interconnected power system make this situation even worse. Aimed at energy saving and system security, a decision optimization method for power grid operating condition with high and low voltage parallel loops is proposed in this paper. Firstly, considering hub substation distribution and power grid structure, parallel loop opening schemes are generated with GN algorithm. Then, candidate opening schemes are preliminarily selected from all these generated schemes based on a filtering index. Finally, with the influence on power system security, stability and operation economy in consideration, an evaluation model for candidate opening schemes is founded based on analytic hierarchy process (AHP). And a fuzzy evaluation algorithm is used to find the optimal scheme. Simulation results of New England 39-bus system and an actual power system validate the effectiveness and superiority of this proposed method.

Background: This study aimed to identify the association between occupational stress and depression-well-being by proposing a comprehensive and flexible job burden-capital model with its corresponding hypotheses. Methods: For this research, 1618 valid samples were gathered from the electronic manufacturing service industry in Hunan Province, China; self-rated questionnaires were administered to participants for data collection after obtaining their written consent. The proposed model was fitted and tested through structural equation model analysis. Results: Single-factor correlation analysis results indicated that coefficients between all items and dimensions had statistical significance. The final model demonstrated satisfactory global goodness of fit (CMIN/DF=5.37, AGFI=0.915, NNFI=0.945, IFI=0.952, RMSEA=0.052). Both the measurement and structural models showed acceptable path loadings. Job burden and capital were directly associated with depression and well-being or indirectly related to them through personality. Multi-group structural equation model analyses indicated general applicability of the proposed model to basic features of such a population. Gender, marriage and education led to differences in the relation between occupational stress and health outcomes. Conclusions: The job burden-capital model of occupational stress-depression and well-being was found to be more systematic and comprehensive than previous models.

This study was conducted to develop a PID control algorithm considering viscosity for the planting depth control system of a rice transplanter using various hydraulic oils at different temperatures and to evaluate the performance of the control algorithm, and compare the performance of the PID control algorithm without considering viscosity and considering viscosity. In this study, the simulation model of the planting depth control system and a PID control algorithm were developed based on the power flow of the rice transplanter (ERP60DS). The primary PID coefficients were determined using the Ziegler–Nichols (Z–N) second method. Routh’s stability criteria were applied to optimize the coefficients. The pole and double zero points of the PID controller were also applied to minimize the sustained oscillations of the responses. The performance of the PID control algorithm was evaluated for three ISO (The International Organization for Standardization) standard viscosity grade (VG) hydraulic oils (VG 32, 46, and 68). The results show that the control algorithm considering viscosity is able to control the pressure of the proportional valve, which is associated with the actuator displacement for various types of hydraulic oils. It was noticed that the maximum pressure was 15.405 bars at 0, 20, 40, 60, 80, and 100 ℃ for all of the hydraulic oils. The settling time and steady-state errors were 0.45 s at 100 ℃ for VG 32, and 0% for all of the conditions. The maximum overshoots were found to be 17.50% at 100 ℃ for VG 32. On the other hand, the PID control algorithm without considering viscosity could not control the planting depth, because the response was slow and did not satisfy the boundary conditions. The PID control algorithm considering viscosity could sufficiently compensate for the nonlinearity of the hydraulic system and was able to perform for any of temperature-dependent viscosity of the hydraulic oils. In addition, the rice transplanter requires a faster response for accurately controlling and maintaining the planting depth. Planting depth is highly associated with actuator displacement. Finally, this control algorithm considering viscosity could be helpful in minimizing the tilting of the seedlings planted using the rice transplanter. Ultimately, it would improve the transplanter performance.

Background: Despite its global eradication in 1977, smallpox remains a concern owing to its potential as a biological agent, thereby prompting the ongoing development and utilization of its vaccine. Vaccination with the Vaccinia virus induces immunity against variola virus, the causative agent of smallpox; however, this immunity does not extend to viruses of different genera within the Poxviridae family. In this study, we aimed to assess the efficacy of an enzyme-linked immunosorbent assay (ELISA) method utilizing Vaccinia virus and recombinant A27L antigen for detecting antibodies against smallpox. Methods. Analysis of serum from 20 individuals pre- and post-vaccination with the CJ strain (CJ50300) revealed neutralizing antibodies, which were confirmed using the plaque reduction neutralization test (PRNT). The ELISA method, validated with a PRNT50 cut-off value of >4, exhibited a sensitivity and specificity of >95% and was particularly reactive with the inactivated virus. Furthermore, adherence to the smallpox vaccination policy revealed significant differences in Orthopoxvirus antibody levels among 300 individuals of different age groups. These findings highlight the reliability and efficacy of the ELISA method in detecting post-vaccination antibodies and contribute significantly to diagnostic methods to prepare for potential smallpox resurgence and bioterrorism threats.

In March 2013, a novel avian influenza A H7N9 virus was emerged in China, which cause rapidly progressive pneumonia and with a high fatality rate. Serologic studies to evaluate neutralizing antibodies of infected patients and birds are invaluable tools for immunogenicity research of H7N9 and epidemiological investigation. Conventional neutralization assays are laborious and time-consuming which also hampered by biosafety requirement. In this study, We construct and produce pseudovirus bearing the full-length hemagglutinin (HA) of H7N9 virus in the Env-defective, luciferase-expressing HIV-1 backbone. The production of lentiviral pseudovirus was analysed by HA gene specific real-time reverse-transcription PCR, transmission electron microscopy (TEM), and Western Blot assay to prove the nucleic acid replication, the morphology of virus, and the expression of HA protein in pseudovirus. After that pseudovirus based inhibition assay was established to detect neutralizing antibodies of a panel of serum samples. Our results demonstrated that H7N9 pseudovirus which had single-cycle infection was generated. By comparing the neutralization antibody titers, pseudovirus based neutralization test could be recognized as an alternative of conventional microneutralization (MN). Hence, we conclude that it is possible to use pseudovirus inhibition assay to screen sera samples, as well as evaluate vaccine-induced neutralizing antibodies against H7N9 virus.

Recently, SMR (Small Modular Reactor) is expected to be able to operate flexibly in conjunction with a high renewable energy penetration grid as a result of improved safety and easy power control compared to large nuclear power plants. SMRs such as South Korea’s System-integrated Modular Advanced ReacTor (SMART) are designed to use canned motors (CMs) for their reactor coolant pumps (RCPs) to enhance safety. The CMs passively enhance the reactor’s safety by preventing leakage of radioactive reactor coolant. However, with motor sizes designed to be as small as possible, and the increased air gap of CMs between stator and rotor, starting torque may be insufficiently small compared to that of similar sized induction motors (IMs). Thusly, CMs may require variable frequency drives (VFDs) to start. This paper compares the torque characteristics of CMs with those of IMs for SMART’s RCPs. ETAP is then used to perform motor starting analysis for CMs started with and without VFDs. The results are presented and analyzed to find out if the VFDs deal with the CM starting torque issue.

Severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2), a novel betacoronavirus, is the causative agent of COVID-19, which has caused economic and social disruption worldwide. To date, many drugs and vaccines have been developed for the treatment and prevention of COVID-19 and have effectively controlled the global epidemic of SARS-CoV-2. However, SARS-CoV-2 is highly mutable, leading to the emergence of new variants that may counteract current therapeutic measures. Electron microscopy (EM) is a valuable technique for obtaining ultrastructural information about the intracellular process of virus replication. In particular, EM allows us to visualize the morphological and subcellular changes during virion formation, which would provide a promising avenue for the development of antiviral agents effective against new SARS-CoV-2 variants. In this review article, we present our recent findings using transmission electron microscopy (TEM) combined with electron tomography (ET) to demonstrate the morphologically distinct types of SARS-CoV-2 particles and the application of EM analysis to evaluate genetically engineered viruses.

Background: Redo mitral valve surgery is the standard of care for failed mitral bioprostheses or recurrence of mitral regurgitation after repair. Nonetheless, catheterbased valve-in-valve (ViV) or valve-in-ring (ViR)-procedures increasingly become viable alternatives in high risk subpopula-tions. Despite reported good initial results, only little is known about longer-term outcomes. The present series report long-term outcomes of transcatheter mitral ViV- and ViR-procedures. Methods: All consecutive patients (n=54) undergoing transcatheter mitral ViV- or ViR-procedures for failed bioprostheses or recurring regurgitation after mitral repair were retrospectively en-rolled in the time period between 2011 and 2021. The mean age was 76.5 ± 6.5 years, and 30 (55.6%) of the patients were male. The procedures were done using a commercially available balloon-expandable transcatheter heart valve. Clinical and echocardiographic follow-up data were obtained out of the hospital’s database and analyzed. Follow-up reached up to 9.9 years with a total of 164.3 patient-years. Results: A total 25 patients received a ViV- and 29 patients a ViR-procedure. Both groups were at high surgical risk with an STS-PROM of 5.9 ± 3.7 % in ViV- and 8.7 ± 9.0% in ViR-patients, respectively (p<0.01). The procedures itself were mainly unevent-ful with no intraoperative deaths and a low conversion rate (n=2/54; 3.7%). VARC-2 procedural success was low (ViV 20.0% and ViR 10.3%; p=0.45), which was either driven by high rates of transvalvular pressure gradients “>5mmHg” (ViV 92.0% and ViR 27.6%; p<0.01) or residual regurgitation “>trace” (ViV 28.0% and ViR 82.7%; p<0.01). ICU-stay was prolonged in both groups (ViV 3.8 ± 6.8 days and ViR 4.3 ± 6.3 days; p=0.96) with acceptable hospital stay (ViV 9.9 ± 5.9 days and ViR 13.5 ± 8.0 days; p=0.13). Despite 30-days mortality was acceptable (ViV 4.0% and ViR 6.9%; p=1.00), the mean posthospital survival time was disappointingly low (ViV 3.9 ± 2.6 years and ViR 2.3 ± 2.7 years; p<0.01). Overall survival I the entire group was 33.3%.Cardiac reasons for death were frequent in both groups (ViV 38.5% and ViR 52.2%). Cox-regression analysis identified ViR-procedures as a predictor of mortality (HR 2.36, CI 1.19 - 4.67, p=0.01). Conclusions: Despite acceptable immediate outcomes in this high-risk subpopulation, long-terms results are discouraging. Transvalvular pressure gradients as well as residual regurgitations remained drawbacks in this real-world population. The indication for catheterbased mitral ViV- or ViR-procedures thoughtfully must be made in consideration of conventional redo-surgery or conservative treatment.

In pattern recognition domain, deep architectures are widely used nowadays and they have achieved fine grades. However, these deep architectures need special demands, especially big datasets and GPU. Aiming to gain better grades without deep networks, we propose a simplified algorithm framework using fusion features extracted from the salient areas of faces. Furthermore, the proposed algorithm has achieved a better result than some deep architectures. For extracting more effective features, this paper firstly defines the salient areas on the faces. This paper normalizes the salient areas of the same location in the faces to the same size, therefore it can gain more similar features from different subjects. LBP and HOG features are extracted from the salient areas, fusion features’ dimensions are reduced by Principal Component Analysis( PCA) and we apply softmax to classify the six basic expressions at once. This paper proposes a salient areas definitude method which uses peak expressions frames to compare with their neutral faces. This paper also proposes and applies the idea of normalizing the salient areas to align the specific areas which express the different expressions. This makes the salient areas found from different subjects have the same size. Besides, gamma correction method is firstly applied on LBP features in our algorithm framework which improves our recognition rates significantly. By applying this algorithm framework, our research has gained state-of-the-art performances on CK+ database and JAFFE database.

The e-commerce sector is in a constant state of growth and evolution, particularly within its subdomain of online food delivery. As such, ensuring customer satisfaction is critical for companies working in this field. One way to achieve this is by providing accurate delivery time estimation. While companies can track couriers via GPS, they often lack real-time data on traffic and road conditions, complicating delivery time predictions. To address this, a range of statistical and machine learning techniques are being employed, including neural networks and specialized expert systems, with different degree of success. One issue with neural networks and machine learning models is their heavy dependence on vast, high quality data. To mitigate this issue we propose two Bayesian generalized linear models to predict time of the delivery. Utilizing a linear combination of predictor variables, we generate practical range of outputs with Hamiltonian Monte Carlo sampling method. These models offer a balance of generality and adaptability, allowing for tuning with expert knowledge. They were compared with PSIS-LOO and WAIC criteria. Results show that both models accurately estimated delivery times from the dataset, while maintaining numerical stability. Model with more predictor variables proved to be more accurate.

In the DC distribution networks, DC bus voltage is maintained by the grid-connected converter, the controllability and reliability of the grid-connected converter significantly affects the bus voltage characteristic. To address the problem of limited stability and frequent oscillations, this paper proposes a state feedback control method for the AC/DC converter. Conventional AC/DC converter adopts the voltage-current double-closed-loop control structure with the proportional integral (PI) controllers, which is the equivalent of the typical type II control system, but the typical type II control system cannot fully settle the stability and immunity problems. In contrast, the state feedback control strategy not only achieves the control objectives of the traditional double-closed-loop control, but also reduce the AC/DC converter system model to a typical I-type system, which improves the stability, thus enhances the oscillation suppression capability of the bus voltage. By selecting multiple state variables and designing the converter pole configuration range, the proposed single-loop state feedback control method manages to optimize both the dynamic and steady-state performances of the grid-connected AC/DC converter. Finally, the effectiveness of the proposed single-loop state feedback control strategy has been verified by both the simulation and experiment results.

In the field of recommender systems, difficult negative samples that are easily misclassified by classifiers have higher learning value. In order to solve the problem that the existing graph convolutional network lacks the exploration of negative sampling strategy, a multivariate sampling based on graph convolution collaborative filtering recommendation model was proposed. Firstly, part of the information in the positive sample was injected into the negative sample, and the high quality difficult negative sample was selected by the inner product method. Then, contrastive learning is used to maximize the similarity between the difficult negative samples and the positive samples, so that the difficult negative samples are as close to the positive samples as possible in the feature space. Ultimately, a multi-task approach was employed to concurrently enhance both the recommendation supervision task and the contrastive learning task. To validate the effectiveness of our approach, we conducted comparative evaluations utilizing three publicly accessible datasets. The experimental outcomes indicate that our proposed model surpasses the baseline model in terms of performance.

The B169L protein (pB169L) of African swine fever virus (ASFV) is a structural protein with an unidentified function during the virus replication. The sequences of the B169L gene and the downstream B438L gene are separated by short intergenic regions. However, the regulatory mode of the gene transcription remains unknown. Here, we identified two distinct promoter regions and two transcription start sites (TSS) located upstream of the open reading frame (ORF) of B438L. Using the promoter reporter system, we demonstrated that the cis activity of the ORF proximal promoter exhibited significantly higher levels compared with that of the distal promoter located in the B169L gene. Furthermore, transfection with the plasmids with two different promoters for B438L could initiate the transcription and expression of the B438L gene in HEK293T cells, and the cis activity of the ORF proximal promoter also displayed the higher activities compared with the distal promoter. Interestingly, the B438L distal promoter also initiated the transcription of the alternatively spliced B169L mRNA (B169L mRNA2) encoding a truncated pB169L (tpB169L) (amino acids 92–169), and the gene transcription efficiency was increased upon mutation of the initiation codon located upstream of the alternatively spliced B169L gene. Taken together, we demonstrated that the distal promoter of B438L gene initiates the transcription of both the B438L mRNA and B169L mRNA2. Comprehensive analysis of the transcriptional regulatory mode of the B438L gene is beneficial for the understanding of the association of B438L protein and pB169L and the construction of the gene-deleted ASFV.

To address the instability of wind power caused by the randomness and intermittency of wind generation, as well as the challenges in power compensation by Hybrid Energy Storage Systems (HESS), this paper proposes a State of Charge (SOC) balancing control strategy based on Successive Variational Mode Decomposition and multi-fuzzy control. First, a consensus algorithm is used to enable communication between energy storage units to obtain the global average SOC. Then, the Secretary Bird Optimization Algorithm (SBOA) is applied to optimize the Successive Variational Mode Decomposition (SVMD) and Variational Mode Decomposition (VMD) for the initial allocation of wind power, resulting in the smoothing power for hybrid energy storage and the grid integration power. Finally, considering the deviation between the current SOC of the storage units and the global average SOC, dynamic partitioning is used for multi-fuzzy control to adjust the initial power allocation, achieving SOC balancing control. Simulations of the control strategy were conducted using Matlab/Simulink, and the results indicate that the proposed approach effectively smooths wind power fluctuations, achieving stable grid integration power. It enables the SOC of the HESS to quickly align with the global average SOC, preventing the HESS from entering unhealthy SOC regions.

This paper presents a system for identification of wind features, such as gusts and wind shear. These are of particular interest in the context of energy-efficient navigation of Small Unmanned Aerial Systems (UAS). The proposed system generates real-time wind vector estimates and a novel algorithm to generate wind field predictions. Estimations are based on the integration of an off-the-shelf navigation system and airspeed readings in a so-called direct approach. Wind predictions use atmospheric models to characterize the wind field with different statistical analyses. During the prediction stage, the system is able to incorporate, in a big-data approach, wind measurements from previous flights in order to enhance the approximations. Wind estimates are classified and fitted into a Weibull probability density function. A Genetic Algorithm (GA) is utilized to determine the shaping and scale parameters of the distribution, which are employed to determine the most probable wind speed at a certain position. The system uses this information to characterize a wind shear or a discrete gust and also utilizes a Gaussian Process regression to characterize continuous gusts. The knowledge of the wind features is crucial for computing energy-efficient trajectories with low cost and payload. Therefore, the system provides a solution that does not require any additional sensors. The system architecture presents a modular decentralized approach, in which the main parts of the system are separated in modules and the exchange of information is managed by a communication handler to enhance upgradeability and maintainability. Validation is done providing preliminary results of both simulations and Software-In-The-Loop testing. Telemetry data collected from real flights, performed in the Seville Metropolitan Area in Andalusia (Spain), was used for testing. Results show that wind estimation and predictions can be calculated at 1 Hz and a wind map can be updated at 0.4 Hz. Predictions show a convergence time with a 95% confidence interval of approximately 30 s.

Multimodal remote sensing data classification can enhance the model’s ability to distinguish land features through multimodal data fusion. In this context, how to help models understand the relationship between multimodal data and target tasks is the focus of researchers. Inspired by human feedback learning mechanisms, causal reasoning mechanisms, and knowledge induction mechanisms, this paper integrates causal learning, reinforcement learning, and meta learning into a unified remote sensing data classification framework and proposed the causal meta-reinforcement learning (CMRL). First, based on feedback learning mechanisms, we have overcome the limitations of traditional implicit optimization of fusion features and customized a reinforcement learning environment for multimodal remote sensing data classification tasks. Through feedback interactive learning between agents and the environment, we help them understand the complex relationships between multimodal data and labels, thereby achieving full mining of multimodal complementary information. Second, based on the causal inference mechanism we designed causal distribution prediction action, classification reward, and causal intervention reward, capturing pure causal factors in multimodal data and cutting off false statistical associations between non-causal factors and class labels. Finally, based on the knowledge induction mechanism, we designed a bi-layer optimization mechanism based on meta-learning. By constructing a meta training task and meta validation task simulation model in the generalization scenario of unseen data, we helped the model induce cross-task shared knowledge, thereby improving its generalization ability for unseen multimodal data. The experimental results on multiple sets of multimodal datasets show that the proposed method achieved state-of-the-art performance in multimodal remote sensing data classification tasks.

Unsmooth reversing is one of the most common faults in the four-way reversing valve of air conditioning system, and the airflow in the valve chamber and the shape of the slider of the reversing valve are the main factors in unsmooth reversing. In order to study the influence of the airflow in the chamber and the slider shape on the reversing process, the fluid flow in the valve chamber of a four-way reversing valve is obtained using computational fluid dynamics (CFD) simulations, and the influence of slider structure on slider thrust and resistance of the four-way reversing valve is analyzed. Four-way reversing valves with no-cutting, straight-cutting and arc-cutting sliders are employed to evaluate the reversing characteristics. A pressure measuring device for a four-way reversing valve chamber is designed, which is performed to test the chamber pressure of three different types of sliders of four-way reversing valves. The maximum error of experimental tests and simulations is within 5% of engineering tolerance, so as to verify the reliability of numerical simulation. The results indicate that the chamber pressure and resistance-thrust ratio with the cutting slider are reduced, which is beneficial to the reversing of the four-way reversing valve. Compared with the straight cutting structure, the arc cutting slider four-way reversing valve has a more stable reversing process and better comprehensive reversing performance. The results can provide a theoretical basis for engineers to improve the performance of four-way reversing valves.

This paper presents an optimized energy management strategy for Li-ion power batteries used on electric vehicles (EVs) at low temperatures. Under low-temperature environments, EVs suffer a sharp driving range loss resulted from the energy and power capability reduction of the battery. Simultaneously, because of Li plating, battery degradation becomes an increasing concern as temperature drops. All these factors could greatly increase the total vehicle operation cost. Prior to battery charging and vehicle operating, preheating battery to a battery-friendly temperature is an approach to promote energy utilization and reduce total cost. Based on the proposed LiFePO4 battery model, the total vehicle operation cost under certain driving cycles is quantified in the present paper. Then given a certain ambient temperature, a target temperature of preheating is optimized under the principle of minimizing total cost. As for the preheating method, a liquid heating system is also implemented on an electric bus. Simulation results show that the preheating process becomes increasingly necessary with a decreasing ambient temperature; however, the preheating demand declines as driving range grows. Vehicle tests verify that the preheating management strategy proposed in this paper is able to save total vehicle operation cost.

As the penetration of renewable energies increases, their acceptance of the power grid system is becoming an important issue. In the case of South Korea, a 22.9kV transformer is frequently utilized to reduce the power loss of the generated renewable energy transmission, so the power quality at the point of common connection (PCC) is inevitably influenced by the nonlinearity of the transformer and the uncertainty of the inductance and resistance of the transmission line. In this paper, we present a point of common connection voltage-modulated direct power control (PCCVM-DPC) system that enhances power quality at the PCC. First, we present the mathematical dynamics of active and reactive power at the PCC side, which contains the step-up transformer’s nonlinearity, the grid voltage harmonics, and the parameter uncertainties. By analyzing the disturbance terms of the PCCVM-DPC system, we present the disturbance observer (DOB) for the PCCVM-DPC system. To assess the efficacy of our approach, we perform comparative studies of the PCCVM-DPC without DOB and PCCVM-DPC with DOB by constructing the simulation environment based on the commercial step-up transformer and ESS inverter datasheet. We have validated that the active and reactive power control performance of the PCCVM-DPC with DOB outperforms the PCCVM-DPC without DOB from the observation that the current total harmonic distortion reduced by more than 40% compared to the PCCVM-DPC without the DOB.

Cytokines play a substantial role in the pathophysiology of infectious diseases. Consequently, genetic polymorphisms in cytokine genes can have profound effect on the susceptibility to or protection from infections and also influence the clinical manifestations, disease severity as well as outcome. The objective of this brief narrative review is to provide an update on the recent research findings on the role of genetic polymorphisms of IL-18, a recently discovered cytokine on certain infectious diseases of public health relevance. The current review suggests there is a significant impact of IL-18 polymorphisms on different infectious diseases. The presence of G and T alleles at position -656 is suggested to have a probable protective effect against VL. The −137G/−607C (GC) and −137C/−607C (CC) haplotypes in the promoter region are associated with increased susceptibility to severe malarial anemia. SNPs rs544354 and rs574429 (GC) are linked to a higher risk of P. falciparum infection and increased parasitemia. The -137 C/C genotype and -137 G allele (with G/G genotype) are associated with faster progression to AIDS. In contrast, the IL-18 genotype does not seem to affect overall HIV susceptibility but influences disease progression. The G and GG genotypes at position -137 and allele A at position -607 are likely associated with protection against HBV infection. Conversely, the C allele at position -137 is linked to increased susceptibility to HBV infections. The GG genotype of IL-18 -137 G > C variant is associated with increased susceptibility to pulmonary tuberculosis (PTB). The AC genotype of IL-18 -607A>C has been linked to PTB susceptibility, particularly in patients with co-morbid diabetes mellitus. SNPs −137G/C, 113T/G, and +127C/T are associated with susceptibility to H. pylori infection, indicating that these genetic variants may influence the risk of H. pylori-related diseases. There are conflicting results in studies conducted in different populations (e.g., genetic polymorphism, studies conducted in India and China against HBV infection) highlighting the need for further research with larger sample sizes to resolve discrepancies. Due to the variability in findings, extensive studies in diverse populations are needed to better understand the impact of IL-18 polymorphisms.

With the global objectives of achieving a ‘carbon peak’ and ‘carbon neutrality’, along with the implementation of carbon reduction policies, China’s industrial structure has undergone significant adjustments, resulting in constraints on high-energy consumption and high-emission industries while promoting the rapid growth of green industries. Consequently, these changes have led to an increasingly complex power system structure and presented new challenges for electricity demand forecasting. To address this issue, this study proposes a 24-step multivariate time series short-term load forecasting algorithm model based on KNN data imputation and BiTCN bidirectional temporal convolutional networks combined with BiGRU bidirectional gated recurrent units and attention mechanism. The Kepler adaptive optimization algorithm (KOA) is employed for hyperparameter optimization to effectively enhance prediction accuracy. Furthermore, using real load data from a wind farm in Xinjiang as an example, this paper predicts the electricity load from January 1st to December 30th in 2019. Experimental results demonstrate that our comprehensive short-term load forecasting model exhibits lower prediction errors and superior performance compared to traditional methods, thus holding great value for practical applications.

The paper presents an error model of a measurement chain containing link performing discrete wavelet transform algorithm which is most often the last stage of measurement signal processing. The goal is to determine the uncertainty budget of the input quantities of the wavelet transform algorithm. The error model takes into account parts of analog, analog-to-digital and digital processing, describing the properties of subsequent fragments of the chain using their transmittance and processing functions. The proposed model enables the description of both deterministic and non-deterministic properties of signal errors. The proposed model was validated using an example measurement chain created for this purpose.

Meningitis is a severe disease associated with death in children under five with highest rates of infections under age of one. Vaccines for Neisseria meningitides and Haemophilus influenza are used to prevent the main causative agents of meningitis. Administration of H. influenzae type b (Hib) vaccine is recommended at 2, 4 and 6 months with a booster dose at 18 months. N. meningitidis has two commercially available vaccines, the pure polysaccharide is recommended at 24 months meanwhile the protein-conjugated vaccines at 12 months. We sought in this study to examine if coadministering the vaccines for the two main meningitis causing bacteria might be synergistic as a preliminary step towards the possibility of shuffling immunization schedule. So, we coadministered Hib vaccine with commercially available vaccines either quadrate (ACWY) polysaccharide meningococcal (Men) or conjugated meningococcal (Nim) vaccines in Balb/C mice (n = 6/group) and compared to each vaccine administered separately and controls. Thirty-five days post immunization, we measured specific antibodies titers. Hib vaccine increased Men antibody titers significantly for serotypes Y and W. When Hib vaccine was coadministrated with Nim, antibody titer for Y, W and A significantly increased. For serotype C, there was no significant difference in antibody titers among immunized groups. As for effect of meningococcal vaccines on Hib, Men significantly increased Hib antibody titers while Nim had no effect. Collectively, our data suggested that coadministration of Hib and Men or Nim vaccines was safe and had synergistic effect on immune responses elicited to both vaccines. Further studies are needed before immunization schedule modifications. Such immunization schedule recommendation should provide better protection against this life-threatening disease in young children.

To date, the development of unmanned technologies using autonomous underwater vehicles (AUV) has become an urgent demand for solving the problem of inspection of industrial sub-sea structures. A key issue here is precise localization of AUVs relative to underwater objects. However, the well-known challenges of recognizing and coordinating underwater objects (impossibility to use GPS, undercurrents, etc.) do not allow high-precision navigation if based solely on a standard suite of AUV navigation tools (sonars, etc.). An alternative is a technology of processing of optical images that, at short distances, can provide higher accuracy of AUV navigation compared to a technology of acoustic measurement processing. In this study, in the context of the problem of subsea production system inspection, we propose a method to recognize underwater objects and provide coordinate reference of AUV to them, based on stereo-image processing. Its distinctive features are the use of a non-standard technique for generating a geometric model of an object from its views (foreshortening) taken from positions of a pre-made overview trajectory, the use of various characteristic geometric elements when recognizing objects, and the original algorithms for comparing visual data of the inspection trajectory with an a priori model of the object.

We evaluated the immunogenicity persistence of different immunization regimens of freeze-dried human rabies vaccine (Vero cells) in the 10–60 years age group of the Chinese population. Based on phase III clinical trials of Vero cells, participants who completed the full course of immunization were continuously enrolled in four-dose trial, five-dose, and five-dose control groups. Venous blood samples were collected 12 months after completion of the full immunization for rabies virus-neutralizing antibody (RVNA) testing, and the antibody-positive rate and geometric mean concentration (GMC) were calculated. Analysis of variance was used to compare three groups. The four-dose trial, five-dose trial, and five-dose control groups included 200, 186, and 214 participants, respectively. Twelve months after full immunization, the overall RVNA-positive rates were 97.00%, 93.55%, and 94.86% in the four-dose trial, five-dose control, and five-dose trial groups, respectively. The post-immunization RVNA GMCs values were 2.50, 2.05, and 2.04 IU/mL, respectively, with no statistically significant differences between them. Twelve months after full immunization, the overall RVNA-positive rate remained high, demonstrating satisfactory immunogenicity persistence for both immunization regimens.

Classifying network flow subsequences in an Industrial IoT gateway is an effective method for identifying Industrial IoT faults. This paper proposes a subsequence classification algorithm SSGBUL-IKNN based on unsupervised learning encoding to address the problem of low classification accuracy. Firstly, we built a network module based on unsupervised learning to encode the flow sequence of the Industrial IoT gateway. In the encoding module, a subsequence calibration algorithm controls the increasing error during the coding process. Then, the specific fault type is obtained through an improved KNN classification algorithm based on the indication distance source from the integrated coding sequences converted by multi-dimensional network flow sequences. The test result on three Industrial IoT datasets of a sewage treatment plant shows that the accuracy of SSGBUL-IKNN in this paper exceeds 92%, significantly higher than the algorithm DTW and TSF. It reaches the classification requirements of Industrial IoT fault diagnosis.

African swine fever virus (ASFV), a highly contagious pathogen characterized by a complex structure and a variety of immunosuppression proteins, causes hemorrhagic, acute, and aggressive infectious disease that severely injure the pork product and industry. However, there is no effective vaccine or treatment. The main reasons are not only the complex mechanisms that lead to immunosuppression, but also the unknown functions of various proteins. This review summarizes the interaction between ASFV and host immune system, along with the involvement of virulence related genes and proteins, as well as the corresponding molecular mechanism of immunosuppression of ASFV, encompassing pathways such as cGAS-STING, NF-κB, JAK/STAT, apoptosis, and other modulation. The aim is to summarize the dynamic process during the ASFV infection and entry into host cell, provide a rational insight into development of vaccine and a better clear knowledge of how ASFV impacts host.

The increasing availability of longitudinal data (repeated numerical observations of same units at different times) requires the development of flexible techniques to automatically detect common errors in such data. Besides obvious and easily identifiable cases, such as missing or out-of-range data, large longitudinal dataset often present problems not easily traceable by the techniques used for generic datasets. In particular, elusive and baffling problems are i) inversion of one or more values from one unit to another; ii) anomalous jumps in the series of values, iii) errors in the timing of the values due to a recalculation operated by the data providers to compensate previous errors. This work proposes a statistical-mathematical approach based on a system of indicators that is able to capture the complexity of the described problems by working at the formal level, regardless of the specific meaning of the data. The proposed approach identifies suspect erroneous data and is applicable in a variety of contexts. We implement this approach in a relevant database of European Higher Education institutions (ETER) by analyzing Total academic staff, that is one of the most important variables, used in empirical analysis as proxy of size and also considered by policy makers at European level.

The numerical implementation of the controllers allows the use of very complex algorithms with ease. However, in practice, due to its proven advantages, the PID controller (and its variants) is widely used in industrial control systems as well as in many other applications that require continuous control. Most of the methods for tuning the parameters of PID controllers are based on time-invariant linear models of the processes, which in practice can lead to poor performance of the control system. The paper presents an application of reinforcement learning algorithms in tuning of PID controllers for the control of some classes of continuous nonlinear systems. Tuning the parameters of PID controllers is done with the help of Twin Delayed Deep Deterministic Policy Gradients (TD3) algorithm which presents a series of advantages compared to other similar methods from Machine Learning dedicated to continuous state and action spaces. TD3 algorithm is an off-policy Actor-Critic based method and was used as it does not require a system model. The presented technique is applied for control of a biotechnological system which has a strongly nonlinear dynamic. The proposed tuning method is compared to the classical tuning methods of PID controllers. The performance of the tuning method based on the TD3 algorithm is demonstrated through simulation illustrating the effectiveness of the proposed methodology.

Understanding the interrelationships between land use, climate change, and regional water yield is critical for effective water resource management and ecosystem protection. However, comprehensive insights into how water yield evolves under different land use scenarios and climate change remain elusive. This study employs the Integrated Valuation of Ecosystem Services and Trade-offs (InVEST) models, Patch-generating Land Use Simulation (PLUS) model, and Geodetector within a unified framework to evaluate the dynamics of land use, water yield, and their relationships with various factors (meteorological, social, economic, etc.). To forecast the Land Use/Cover Change (LUCC) pattern of the Yellow River Basin by 2030, three scenarios were considered: economic development priority (Scenario1), ecological development priority(Scenario2), and cropland development priority(Scenario3). Climate change scenarios were constructed using CMIP6 data, representing low stress (SSP119), medium stress (SSP245), and high stress (SSP585) conditions. The results show the following: (1) From 2000 to 2020, cropland was predominant in the Yellow River Basin, Henan Province, with significant land conversion to impervious land (construction land) and forest land; (2) Water yield changes during this period were primarily influenced by meteorological factors, with land use changes having negligible impact; (3) By 2030, the water yield of Scenario1 is highest among different land use scenarios, marginally surpassing ecological development priority by 0.5%; (4) Climate scenarios reveal significant disparities, with SSP126 yielding 67% higher water production than SSP245, driven predominantly by precipitation; (5) Geodetector analysis identifies precipitation as the most influential single factor, with significant interactions among meteorological and socio-economic factors. These findings offer valuable insights for policymakers and researchers in formulating land use and water resource management strategies.

The electroencephalogram (EEG) is a record of brain activity. Brain Computer Interface (BCI) technology formed by the EEG signal has become one of the hotspots at present. How to extract the feature signal of EEG is the most basic research of BCI technology. In this paper, A new method of recognizing fatigue, conscious, concentrated state of human brain is proposed by the combination of discrete wavelet transform and the neural network based on EEG signal. First of all, the law signal is preprocessed by the wavelet denoising method because the law EEG signal contains a large number of high frequency noise, which is decomposed into multi-layer high frequency signal and low frequency signal. thus, δ wave, θ wave, α wave, β wave are obtained by the wavelet transform. And then, frequency band energy of the different wave is regards as the feature signal of EEG. In the experiment, the feature signal is classified by radial basic function (RBF) and annealed chaotic competitive learning network (ACCLN). RBF and ACCLN networks are trained with 500 sets of sample data and are tested by 100 sets of samples in different mental states. The experimental results show that the average accuracy of RBF network under three conditions are 88.75%, 88.25%, 88.5%, respectively, and the correct rate of ACCLN network is 97%, 98%, 98%, respectively.

Addressing the issue of compromised performance and stability in distributed drive electric vehicles during high-speed operation in the event of motor failure. A fault-tolerant control strategy for distributed drive electric vehicles is proposed, based on Model Reference Adaptive Control (MRAC). First, a seven-degree-of-freedom vehicle dynamics reference model is established, from which the output torque of each wheel during stable operation is determined. Secondly, based on the compensation principle that maintains constant longitudinal speed and total torque before and after the fault, the output torque of the remaining wheels is determined to ensure normal vehicle operation in the event of a single motor failure. To improve torque distribution accuracy, an MRAC controller that takes into account the output hysteresis of the motor is designed. The transfer functions of both the reference model and the actual model are derived. Using Lyapunov's second method, the adaptation rate of the MRAC system is formulated, ensuring that the state of the actual model converges to that of the reference model, thereby achieving adaptive regulation of system parameters and global stability. Finally, simulation experiments are conducted under high-speed dual-lane conditions. The results indicate that, in the case of a single motor failure with constant vehicle speed, the yaw rate and lateral displacement of the vehicle's center of mass decrease, thereby validating the effectiveness of the proposed fault-tolerant control strategy.

Previous control methods developed by our research team cannot satisfy the high-accuracy requirements of unmanned surface vessel (USV) path-tracking during bathymetric mapping because of the excessive overshoot and slow convergence speed. For this reason, this study developed an adaptive fuzzy integral-derivative line-of-sight (AFIDLOS) guidance law for USV path-tracking control. Integral and derivative terms were added to counteract the effect of the sideslip angle, with which the USV could be quickly guided to converge to the planned path for bathymetric mapping. To obtain a high-accuracy of the look-ahead distance, a fuzzy control method was proposed. The proposed method was verified using simulations and outdoor experiments. The results demonstrate that the AFIDLOS guidance law can reduce the overshoot by 79.85%, shorten the settling time by 55.32% in simulation experiments, and reduce the average cross-track error by 10.91%, and can ensure a 30% overlap of neighboring strips of bathymetric LiDAR outdoor mapping when compared with the traditional method.

The Myval is a balloon-expandable transcatheter heart valve (THV) devel-oped by Meril Life Sciences Pvt. Ltd. that has innovative operator-friendly de-sign which aids to improve deliverability and features precise deployment. Vari-ous clinical studies demonstrate its effectiveness and safety, making it a promis-ing choice in valvular interventions. Myval has been successfully utilized as a transcatheter aortic valve implanta-tion (TAVI) device in cases with conduction disturbances, bicuspid aortic valve anatomy, non-calcified aortic regurgitation, dysfunctional stenosed right ventric-ular outflow tract (RVOT) conduits, pulmonary valve replacement, mitral valve replacement, Vave-in-valve and Valve-in-ring implantation procedures. Myval’s diverse sizes are also of key importance in complex cases of large and complex annuli anatomy. Further long-term studies are needed to consolidate these results. Its introduction signifies a significant advancement in cardiology, aiming to enhance patient outcomes and quality of life. In the present review, we provide an update on new-generation Myval THVs and review the available clinical data published till date with an emphasis on diverse use in specific clinical scenarios.

When grid-following (GFL) and grid-forming (GFM) converters are interconnected with the grid, they are mutually coupled through the grid impedance. During grid faults, the transient behavior of these converters becomes intricate due to the presence of coupling terms. Instabilities in one converter can propagate to the other, posing challenges to fault ride-through capability. Firstly, a mathematical model was presented for a hybrid grid-tied system comprising two converters, investigated the conditions for equilibrium points, and employed phase-plane analysis to elucidate the mutual influence mechanism during faults. Then, a method to adjust the power angle of GFM according to the voltage drop was proposed and used in GFL to improve its phase-locked loop. At the same time, considering the influence of GFL current injection, the fault current of GFM was limited, so as to realize the hybrid fault ride-through control. The proposed approach ensures that GFM converters contribute reactive current support to the grid during faults, while GFL converters adhere to grid guidelines for current injection, thereby preventing overcurrent and phase angle instability in both converters. Finally, simulation results validated the correctness and effectiveness of the proposed control strategy.

The attitude dynamics and orbit dynamics of large rigid space structures are coupled with each other under gravity gradient, which may affect the stability of the large rigid space structures. In this paper, the gravity gradient stability of a large rigid space structure is studied under both small and large disturbances. Based on the rigid body dynamics and orbit dynamics, an accurate dynamic model without any linearization of the large rigid space structure is established via the natural coordinate formulation (NCF), which is able to describe the large overall motions of the structures. By using the generalized-α algorithm, the gravity gradient stability of the large rigid space structure is simulated and analyzed via various examples, including the influence of large disturbance angles, the positions at the stabilization and unstabilization regions. Finally, the relationship between spinning stability and gravity gradient stability is also investigated via a large spinning space structure.

The main objective of the present study is to demonstrate the possibility of actively influencing the position of the bow shock wave and the main parameters of supersonic flow over a blunt body by organizing a gas discharge near the front surface, in the region between the body and the bow shock wave. The research is carried out using both experimental and numerical methods. The working gas was xenon. It is shown that the steady bow shock wave stand-off distance along with the current and power of the discharge, is associated with the change in the adiabatic index of the plasma created by the discharge, which, in turn, is determined by the plasma parameters, such as the degrees of nonequilibrium and the degree of ionization. It is shown that the adiabatic index with the power supplied to the impact zone in the range of 30-120 kW can both increase and de-crease in the range of 1.25-1.288. The study of the discharge created plasma zone was conducted and the correspondence between the discharge current and power, and the average parameters in the plasma zone created by the discharge is presented. A good agreement between the numerical and experimental data was shown. The results may be useful in developing control systems for high-speed civil aircrafts.

The emerging wireless energy transfer technology enables sensor nodes to maintain perpetual operation. However, maximizing the network performance while preserving short charging delay is a great challenge. In this work, a Wireless Mobile Charger (WMC) and a Directional Charger (DC) are deployed to transmit wireless energy to the sensor node to improve the network's throughput. To the best of our knowledge, this is the first work to optimize the data sensing rate and charging delay by joint scheduling of MC and DC. We prove we can transmit maximum energy to each sensor node to obtain our optimization objective. In our proposed work, a DC selects a total horizon of equipped with DCs, which selects the horizon of each specific area with based on its antenna orientation. DC's orientation is scheduled for each time slot. Furthermore, multiple MCs are used to transmit energy for sensor nodes which cannot be covered by DCs. We divided the Rechargeable Wireless Sensor Network into several zones via the Voronoi diagram. We deployed a static DC and one MC charging location in each zone to provide wireless charging service jointly. We obtain the optimal charging location of MCs in each zone by solving Mix Integral Programming for energy transmission. The optimization objective of our proposed research is to sense maximum data from each sensor node with the help of maximum energy. The lifetime of each sensor network can increase, and the end delay can be maximized with joint energy transmission. Extensive simulation results demonstrate that our RWSNs are designed significantly to improve network lifetime over the baseline method.

This paper proposes a novel single-stage buck-boost three-Level neutral-point-clamped (NPC) inverter with two independent dc sources coupled for the grid-tied photovoltaic (PV) application, which can effectively solve the unbalanced operational conditions generally appeared between two coupled independent PV sources induced by the unequal irradiation and temperature distribution. The proposed control scheme can simultaneously guarantee the maximum power point (MPP) operation of both PV sources and maintain the output waveform quality. Compared to the traditional two-stage PV inverter, the proposed NPC inverter could reduce the PV array voltage requirement and dc-link capacitors’ voltage rating, meanwhile show the advantage in operational efficiency. MATLAB simulations and the captured experimental results are presented to show the performance of the proposed three-level inverter.

To maximize resource usage, minimize disputes, and improve academic experience, professors must schedule teaching activities efficiently. This study provides an optimized automated schedule creation technique. The system generates conflict-free, efficient schedules using evolutionary algorithms and multi-objective optimization. Resource usage, scheduling prob-lems, and faculty/student satisfaction are the goals of the research. The system optimizes scheduling based on room limitations, instructor availability, and student preferences. The project uses system design, model creation, algorithm implementation, and performance analysis to solve the difficult timetable-generating problem. This research should save administrators time, improve academic operations, and improve staff and student academic experiences. Scalability and flexibility allow the system to be used in multiple faculties and incorporate new limits and requirements. This paper presents a complete approach to faculty scheduling, including insights and recommendations for future study and application in educational institutions.

Aiming at the problems of inaccurate segmentation of long object and information loss of small object in real-time semantic segmentation algorithm, this paper proposes a lightweight multi-branch real-time semantic segmentation network based on BiseNetV2. The new auxiliary branch makes full use of spatial details and context information to cover the long object in the field of view. Meanwhile, in order to ensure the inference speed of the model, the asymmetric convolution is used in each stage of the auxiliary branch to design a structure with low computational complexity. In the multi-branch fusion stage, the alignment and fusion module is designed to provide guidance information for deep and shallow feature mapping, so as to make up for the problem of feature misalignment in the fusion of information at different scales, and thus reduce the loss of small target information. In order to further improve the model’s awareness of key information, a global context module is designed to capture the most important features in the input data. The proposed network uses NVIDIA GeForce RTX 3080 Laptop GPU experiment, on the road street view data set Cityscapes and CamVid average occurring simultaneously ratio reached 77.1% and 78.4% respectively, with running speed of 127 frames/s respectively and 112 frames/s. The experimental results show that the proposed algorithm can achieve real-time segmentation and improve the accuracy significantly, showing good semantic segmentation performance

Model-based fault diagnosis serves as a powerful technique for addressing fault detection and isolation issues in control systems. However, diagnosing faults in closed-loop control systems is more challenging due to their inherent robustness. This paper aims to detect and isolate actuator and sensor faults in the cascade electro-hydraulic control system of a turbofan engine. Based on the fault characteristics, we design a robust unknown perturbation decoupling residual generator and an optimal fault observer specifically for the inner and outer control loops to detect potential faults. To locate the faults, we analyze the steady-state propagation laws of actuator and sensor faults within the loops using the final value theorem. Based on this, we establish the minimal-dimensional fault influence distribution matrix specific to the cascade turbofan engine control system. Subsequently, we construct the normalized residual vectors and monitor its vector angles against each row of the fault influence distribution matrix to isolate faults. Experiments conducted on an electro-hydraulic test bench demonstrate that our proposed method can accurately locate four typical faults of actuators and sensors within the cascade electro-hydraulic control system. This study enriches the existing fault isolation methods for complex dynamic systems, and lays the foundation for guiding component repair and maintenance.

High dimensional statistical analysis for the yield of large-scale circuits is quite difficult due to expensive simulations, especially for the memory circuits with high sigma requirement (e.g., SRAM). In this paper, we developed an efficient sparse additive model to substitute simulations. To fit high sigma region accurately, the modeling center is moved to near failure boundary searched by scaling the shape of sampling function. To solve the model efficiently, the process variables are grouped by standard cells so that the model can be solved by our developed blockwise greedy algorithm. The experiments on the 28nm memory circuits validate that our method achieves high accuracy and efficiency compared with other state-of-art works.

Transcatheter Aortic Valve Implantation (TAVI) now represents the mainstay in the treatment of severe aortic stenosis. Owing to its exceptional procedural efficacy and safety, TAVI has been extended to include patients at lower surgical risk, thus now encompassing a diverse patient population receiving this treatment. Yet, long-term outcomes also depend on optimal medical therapy for secondary vascular prevention, with antithrombotic therapy serving as a cornerstone. Leveraging data from multiple randomized controlled trials, current guidelines generally recommend single antithrombotic therapy, with either single antiplatelet therapy (SAPT) or oral anticoagulation (OAC) alone in those patients without, or with atrial fibrillation respectively. Yet, individualization of this pattern, as well as specific case uses, may be needed based on individual-patient characteristics and concurrent procedures. This review aims to discuss the evidence supporting antithrombotic treatments in patients treated with TAVI, indications for a standardized treatment, as well as specific considerations for an individualized approach to treatment.

In modern times, technology has become more than just a tool; it is a vital component of our lives, driving society and humanity towards new horizons, better living standards, and solu-tions for complex, global challenges. This article explores the world of dependable systems, specifically focusing on system design, software solutions, and architectural decisions that fa-cilitate collaborative work. It aims to dive into the intricacies of designing robust and effective document collaboration software. Throughout this paper, readers will gain insights into the proposed design process, enabling them to understand, learn from, and critically evaluate the examined methodologies and outcomes. Like everything else in the software technology field, there are multiple solutions to any given problem, and this work is no exception to this rule. The objective of this study is to provide a detailed architectural overview of the microservices pattern in an orchestrated cloud environment based on independent containers. To examine the pros and cons of such a system, the paper will detail how a real-time document collaboration system can benefit from such an architecture regarding availability, elasticity, scaling, and disaster recovery. Moreover, the paper will analyze how cloud-native technologies can be used to create a scalable platform solution, capable of handling traffic, dynamic resource storage, asynchronous com-munication, and application scaling. The intricate nature of this system renders this paper a valuable resource for prospective investigations within the domain of dependable systems, cloud computing, and distributed systems. This paper not only showcases the design and implementation process but also sets a founda-tion for future research and innovation in dependable systems, collaborative technologies, sustainable solutions, and distributed system architecture.

In small data set learning, obtaining a large number of training samples from the source class for transfer learning is a challenge for fine-grained visual classification. Based on the fact that fine-grained concepts can be learned with very few samples, we use very few labeled samples (for example, three) in each category. However, due to the difficulty in distinguishing the subtle differences between fine-grained images, we propose a local structure information extraction method of SDFGVC based on spatial frequency features. The proposed learning module enhances the ability of the network to find significant regions and shows excellent performance in experiments on six datasets.

Online food delivery services are rapidly growing in popularity, making customer satisfaction critical for company success in a competitive market. Accurate delivery time predictions are key to ensuring high customer satisfaction. While various methods for travel time estimation exist, effective data analysis and processing are often overlooked. This paper addresses this gap by leveraging spatial data analysis and preprocessing techniques to enhance the data quality used in Bayesian models for predicting food delivery times. We utilized the OSRM API to generate routes that accurately reflect real-world conditions. Next, we visualized these routes using various techniques to identify and examine suspicious results. Our analysis of route distribution identified two groups of outliers, leading us to establish an appropriate boundary for maximum route distance to be used in future Bayesian modelling. The spatial analysis revealed that these outliers were primarily deliveries to the outskirts or beyond the city limits. By refining the data quality through these methods, we aim to improve the accuracy of delivery time predictions, ultimately enhancing customer satisfaction.

Introduction: Known for its persistent blood-feeding behavior from dawn to dusk, Aedes albopictus is recognized as one of the most dangerous mosquito species due to its role as a vector for diseases such as dengue. Studies have demonstrated that Aedes albopictus thrives in micro-breeding sites predominantly located on private properties, including abandoned containers and manholes used for rainwater and irrigation. This study investigates an innovative methodology, the TombiniNet, to mitigate the proliferation of Aedes albopictus by engaging citizens in the active management of micro-breeding sites on their properties. Materials and Methods: The study was conducted in Alessandria, a city with approximately 100,000 inhabitants, focusing on a sample of 200 houses and a population of about 5,000 people. Researchers conducted a comprehensive survey and analysis of micro-breeding sites for Aedes albopictus on both private and communal properties. The larval control measures were conducted from April to October, aligning with the peak mosquito breeding season. The study's sample included 51% of houses that allowed researchers access, and within these, 81% had Aedes albopictus larvae, often found in diverse water Containers holes of which basically manholes on villa garden floors. For monitoring the adult populations were used ovitraps that were not placed in private homes but in public areas to monitor and control the mosquito population. Results: The study identified that up to 70% of micro-breeding sites for Aedes albopictus in northern Alessandria were located on private properties. Citizen participation was critical to the success of the intervention, with a marked decrease in the number of adult tiger mosquitoes observed in areas where residents actively managed breeding sites using the TombiniNet. The TombiniNet was particularly effective in private areas, as it could be regularly maintained by residents, preventing debris accumulation that could hinder drainage. Discussion: The findings highlight the importance of engaging citizens in mosquito control programs to effectively manage Aedes albopictus populations in urban areas. The TombiniNet intervention demonstrated that a simple, cost-effective solution could significantly reduce mosquito breeding sites on private properties. By addressing both communal and private breeding sites, a comprehensive and sustainable approach to mosquito management can be achieved, thereby reducing the risk of disease transmission. Future studies should focus on long-term monitoring and the development of additional innovative solutions to enhance citizen participation and control measures. The study's success also pointed out the limitations of applying such interventions in public areas where debris could impede the net's effectiveness.

The severe climate changes due to global warming pushed the world to strive to reduce carbon emissions. This study aims to minimize the carbon emissions for a proposed smart energy hub. This paper prioritizes the minimization of carbon emissions, taking into consideration the minimization of operation running costs, and the maximization of profit. In this paper two optimization scenarios were studied, to compare the results. In the first scenario, the minimization of carbon emissions was achieved, in the second scenario, the minimization of running costs and maximization of profit from the hub assets were studied. The proposed model was designed in MATLAB. Then the results were verified by CPLEX and validated by RTDS. The multi-objective model was presented to obtain the optimal operation. The mitigation of data uncertainty was achieved by applying the Kalman filter. In this work, a novel method was proposed for the estimation of the quarter-hour resolution data from the hourly one via the Kalman filter rather than applying the classic polynomial interpolation methods.

Heavy rains result in significant threats to human health and life. Floods and other natural disasters, which have a global impact annually, can be attributed to extended periods of intense precipitation. Accurate rainfall prediction is crucial in nations such as Bangladesh, where agriculture is the predominant field of occupation. The efficiency of machine learning methods is enhanced by the nonlinearity of rainfall, surpassing the effectiveness of other approaches. This study proposes the novel combination of rainfall occurrence prediction, rainfall amount prediction, and daily average temperature prediction. This research implements machine learning techniques and an ensemble-based classifier to predict rainfall occurrence, as well as machine learning regressor models and an ensemble-based regressor to predict the rainfall amount and daily average temperature, using the Bangladesh Weather Dataset. The ensemble classifier demonstrated an accuracy of 83.41% and a recall of 78.17%, exhibiting the best performance in predicting when it will rain, but its precision was the lowest, at 51.16%. The ensemble regression model outperformed the base models, including linear regression, random forest, and support vector regression in rainfall amount prediction, with the lowest mean absolute error of 0.36 and root mean squared error of 0.90. Additionally, this model provided the most precise daily average temperature prediction results with the lowest mean absolute error of 0.42 and root mean squared error of 0.54, highlighting its superiority over the other regression models in forecasting temperature. Ensemble approaches consistently exhibit superior task performance metrics.

Mammarenavirus Wenzhouense (WENV) is broadly distributed in Asia, while the he dynamics process of WENV infection remains unclear. A field derived strain of WENV was used to inoculate Sprague-Dawley (SD) rats by intramuscular injection, the process of virus infection was de-tected by controlling time for 28 days. Viral RNA became detectable in the blood at 3 d pi, and remained detectable for about 12 d. In most organ tissues, viral RNA peaked at 7 d pi, then began to decline by 14 d, however remained detectable in intestine and brain tissues at 21 and 28 d pi. Virus shedding had been detected from fecal samples for 5 days from 6 to 11 d pi using qRT-PCR, and was recovered from feces collected at 8 d pi. Horizontal contact infection occurred among cage-mates at 14 and 21 d pi. Antibodies against the nucleocapsid were detected at 5 dpi, next increased and persisted until the end of experiment. The results enabled to discriminate the kinetic of viremic response, virus shedding in feces and horizontal transmission, as well as the potential sites for WENV replication or maintenance of the virus in nature.

This study explores fault-tolerant consensus in leader-following heterogeneous multi-agent systems, focusing on actuator failures in uncrewed aerial vehicles (UAVs) and uncrewed ground vehicles (UGVs). An optimization-based fault-tolerant consensus algorithm is proposed. The algorithm utilizes the Euler-Lagrange formula to ensure system consistency under actuator failures, with the Lyapunov stability theory proving the asymptotic stability of the consistency error. The algorithm is applied to heterogeneous multi-agent systems of UAVs and UGVs to derive optimal fault-tolerant consensus control laws for each vehicle type. Simulation experiments give evidence for the feasibility of the proposed control strategy.

Background/Objectives: Infectious Endocarditis often requires surgical intervention, with postoperative acute kidney injury (AKI) posing a significant concern. This retrospective study aimed to investigate AKI incidence, its impact on short-term mortality, and identify modifiable factors in patients with endocarditis scheduled for valve surgery. Methods: This single center study enrolled 130 consecutive endocarditis patients from 2013 to 2021 undergoing valve surgery. Creatinine levels were monitored pre- and postoperatively, and AKI was defined by Kidney Disease: Improving Global Outcomes (KDIGO) criteria. Patient demographics, comorbidities, procedural details, and complications were recorded. Primary outcomes included AKI incidence, the relevance of creatinine levels for AKI detection, and the association of AKI with 30-, 60- and 180-day mortality. Modifiable factors contributing to AKI were explored as secondary outcomes. Results: Postoperatively, 35.4% developed AKI. The highest creatinine elevation occurred on the 2nd postoperative day. Best predictive value for AKI was a creatinine level of 1.35 mg/dl on the 2nd day (AUC: 0.901; sensitivity: 0.89, specificity: 0.79). Elevated creatinine levels on the 2nd day were robust predictors for short-term mortality at 30, 60 and 180 days postoperatively (AUC ranging from 0.708 to 0.789). CK-MB levels at 24 hours postoperatively and minimum hemoglobin during surgery were identified as independent predictors for AKI in logistic regression. Conclusions: This study highlights the crucial role of creatinine levels in predicting short-term mortality in surgical endocarditis patients. A specific threshold (1.35 mg/dl) provides a practical marker for risk stratification, offering insights for refining perioperative strategies and optimizing outcomes in this challenging patient population.

Minimally invasive approaches to the aortic valve have been described since 1993, with great hopes that they would become universal and facilitate day-case cardiac surgery. The literature has shown that these procedures can be undertaken with equivalent mortality, similar operative time, comparative cost and some benefits in hospital length of stay. The competing efforts of the transcatheter aortic valve implantation for these same outcomes have provided an excellent range of treatment options for patients from the Heart Team. We describe the current state of the art, including technical considerations, caveats and complications of minimal access aortic surgery and predict future directions in this space.

In the realm of digitalization, data play a crucial role across various scientific fields, from physics to engineering. Analyzing data with advanced technologies like artificial intelligence enhances en-gineers' ability to make informed judgments on product quality. This study aligns with the digital-ization trend by implementing formula generation, generalization, and optimization using genetic algorithms and three machine learning approaches: support vector regression, Gaussian process regression, and artificial neural networks, on a grinding process dataset from a previous study on UNS S34700 steel. The study introduces new approaches by considering three different grinding wheels and four cooling and lubrication solutions as influential process parameters, previously considered qualitative and fixed in earlier literature. Additionally, seven different depths of cut were implemented to measure surface roughness and grinding forces (tangential and normal). Qualitative data were encoded into quantitative data using standard techniques. By enhancing genetic algorithm optimization, a relational formula with 25 coefficients was developed to describe the relationship between input parameters and outputs. Three machine learning algorithms were evaluated for predicting the relationship between predictors and responses. The flexibility and scalability of these methods, combined with the relational formula, provide a sophisticated ap-proach for future expansions. The formula evaluation achieved around 85% accuracy for surface roughness and 90% for grinding forces. In machine learning approaches, the GPR method reached model stability with an R² of around 0.98 and a mean accuracy of 93%, while the ANN reached an R² of around 0.96 and a mean accuracy of 90%. This shows that machine learning approaches are more suitable than formula generalization. The scalability and flexibility of machine learning help generalize with more data variety, while the formula evaluation only accepted current data sets. Furthermore, ML methods achieve high accuracy and are suitable for predicting future data, aligning with digitalization and trend prediction.

Following the detection of highly pathogenic avian influenza (HPAI) virus in countries bordering Kenya to the west, we conducted surveillance among domestic and wild birds along the shores of Lake Victoria. In addition, between 2018 and 2020, we conducted surveillance among poultry and poultry workers in live bird markets and among wild migratory birds in various lakes that are resting sites during migration to assess introduction and circulation of avian influenza viruses in these populations. We tested 7,464 specimens (oropharyngeal and cloacal swabs) from poultry and 6,531 fresh fecal specimens from wild birds for influenza A viruses by real-time RT-PCR. Influenza was detected in 3.9% (n=292) of specimens collected from poultry and 0.2% (n=10) of fecal specimens from wild birds. On hemagglutinin subtyping, most of the influenza A positives from poultry (274/292, 93.8%) were H9. Of 34 H9 specimens randomly selected for further subtyping, all were H9N2. On phylogenetic analysis, these viruses were genetically similar to other H9 viruses detected in East Africa. Only two of the ten influenza A positive specimens from the wild bird fecal specimens were successfully subtyped; sequencing analysis of one specimen collected in 2018 was identified as low pathogenicity avian influenza H5N2 virus of the Eurasian lineage and the second specimen, collected in 2020, was subtyped as H11. A total of 18 OP/NS swabs from poultry workers with ARI (12%) were collected; none were positive for influenza A virus. We observed significant circulation of H9N2 influenza viruses in poultry in live bird markets in Kenya. During the same period, low pathogenic H5N2 virus was detected in a fecal specimen collected in a site hosting a variety of migratory and resident birds. Although HPAI H5N8 was not detected in this survey, these results highlight the potential for introduction and establishment of highly pathogenic avian influenza viruses in poultry populations and the associated risk of spillover to human populations.

This article presents a buck converter in which the inductor has been replaced by a transmission line. This approach would be practically conceivable if the power supply and load have a greater spatial distance. In the time domain, this new converter can be described by a system of coupled partial and ordinary differential equations. In the frequency domain, a transcendental transfer function is obtained. For comparison with an equivalently parameterized conventional converter, Padé approximants are derived. A linear controller is designed for the converter topology under consideration.

This study focuses on predicting PM2.5 levels at the University of Petroșani by employing advanced machine learning techniques to analyze a dataset that encapsulates a wide array of air pollutants and meteorological factors. Utilizing data from IoT sensors and established environmental monitoring stations, the research leverages Random Forest, Gradient Boosting Machines, and Support Vector Regression models to forecast air quality, emphasizing the complex interplay between various pollutants. The models demonstrate varying degrees of accuracy, with the Random Forest model achieving the highest predictive power, indicated by an R2 score of 0.82764. Our findings highlight the significant impact of specific pollutants such as NO, NO2, and CO on PM2.5 levels, suggesting targeted mitigation strategies could enhance local air quality. Additionally, the study explores the role of temporal dynamics in pollution trends, employing time-series analysis to further refine the predictive accuracy. This research contributes to the field of environmental science by providing a nuanced understanding of air quality fluctuations in a university setting and offering a replicable model for similar environments seeking to reduce airborne pollutants and protect public health.

When a grid-forming (GFM) inverter is connected to a low or medium voltage weak power grid, the line impedance with resistive-inductive characteristics will cause power coupling. Typical GFM decoupling control strategies are designed under nominal line impedance parameters. However, there are deviations between the nominal line impedance and actual parameters, resulting in poor decoupling effects. Aiming at this problem, this paper proposes a power decoupling strategy based on a reduced-order extended state observer (ESO). Firstly, the power dynamic model of GFM is established based on the dynamic phasor method. Then, the model deviation and power coupling due to line impedance parameter perturbation are estimated as internal disturbances of the system, and the disturbances are compensated on the basis of typical power control strategy and virtual impedance decoupling. Good decoupling performance is obtained under different impedance parameters, improving the control strategy's robustness. Finally, the effectiveness of the proposed method is verified by the results of RT Box hardware-in-the-loop experiments.

Sea cucumber peptides are small molecular peptides with biological function obtained from fresh sea cucumber as feedstock, which were hydrolyzed by protease, separated ,and purified. As the main product of sea cucumber refinement, it more accurately expresses the nutritional effect of sea cucumber and has a wide range of potential applications. It has been demonstrated that sea cucumber has a certain value-added effect on bone mineral density regulation, but the differences in bone mineral density regulation of extracts from different parts of sea cucumber and the techniques contributing to the efficient isolation of bone sea cucumber peptides have not been reported. Firstly, the aim of this study was to reveal the differences in osteogenic activities of enzymatic peptides from three major parts of sea cucumber: the body wall, the egg protein, and the intestinal protein. Then, the bone-enhancing sea cucumber peptides were isolated based on the characteristics of the dif-ferences in molecular weight distribution, hydrophilicity, and ionisation degree of sea cucumber, and to explore the possible mechanisms of their action. The findings indicated that sea cucumber peptides extracted from three distinct sites exhibited a dose-dependent enhancement of osteoblast proliferation and differentiation. Upon evaluating the three methods of sea cucumber peptide separation based on molecular weight distribution, hydrophilicity, and ionization, it was observed that the fraction isolated by hydrophobicity and

Only a handful of microbial mosquito larval pathogens have been described to date. Sampling of several natural enzootic infections of mosquito larvae in southwestern Florida indicated the presence of microbial pathogens capable of extensive larval mortality. Microscopic analysis of one sample site revealed extensive apparent growth of a Pythium-like microbe on mosquito lar-vae, with highest infection observed on the siphon and head regions. Structures consistent with sporangia were seen on infected insects after lactophenol blue staining, and higher resolution scanning electron micrographs (SEM) showed sporangia and encysted zoospores targeting the head and siphon regions. The isolate was single colony purified and molecular identification targeting the ITS and COX1 loci coupled to phylogenetic reconstruction indicated that the isolate belonged to the Pythium genus, but was distinct from its closest characterized species, P. angusta-tum. Morphological features were characterized, with the isolate showing rapid growth on all mycological media tested and relatively high thermotolerance, capable of robust growth at 37oC, and hence was designated, P. thermoculicivorax. Sampling from a second series of natural infec-tions of mosquito larvae resulted in the molecular identification of three Trichoderma isolates, one with high similarity to T. strigosum, and the other two clustering with, but distinct from, T. asperellum. These data highlight the occurrence of natural enzootic infections of mosquito larvae, potentially as a resource for the identification of new mosquito pathogens.

Harmful algal blooms are a serious problem for humanity, so the development of tools and methods for their timely detection is an urgent task. The use of optical methods often allows scientists to solve problems of remote and automated monitoring. Temperature spectra of fluorescence can be used as distinctive features of algae, and the fluorescence parameters obtained from them can be used for identification. The paper presents a description of the fluorescence parameters of Alexandrium catenella, and shows their stability during cumulative cultivation. In addition, the cytometric properties of the culture and its pigment composition were studied. In addition, the article compares all the studied properties of this microalga with the alga Prorocentrum cordatum. We demonstrated clear differences in their fluorescence parameters, which makes it possible to distinguish these microalgae by optical methods, for example, during their dominant blooms.

Transcatheter aortic valve implantation (TAVI) has grown exponentially within the cardiology and cardiac surgical spheres. It has now become a routine approach for treating aortic stenosis. Several uncertainties have been raised about TAVI in comparison to conventional surgical aortic valve replacement (SAVR). The primary concerns are with regards to the longevity of the valves. Several factors have been identified that may predict poor outcomes following TAVI. These include the lesser-used finite element analysis (FEA) to quantify the properties of calcifications that affect TAVI valves. This can also be used in conjunction with other integrated software to ascertain the functionality of these valves. Other imaging modalities are now widely available such as Multi-detector row computed tomography(MDCT) which can accurately size the aortic valve annulus.. This may help reduce the incidence of paravalvular leaks and regurgitation which may necessitate further intervention. Structural valve degeneration (SVD) remains a key factor with varying results from current studies. The true incidence of SVD in TAVI compared to SAVR remains unclear with the lack of long term data. It is now widely accepted that both are part of the armamentarium and are not mutually exclusive. Decision-making for the appropriate intervention should be made via shared decision-making involving the heart team.

Starting from the fact that one of the global control strategies of the Permanent Magnet Synchronous Motor (PMSM), namely the Direct Torque Control (DTC) type control strategy, is characterised by the fact that the inner flux and torque control loop usually uses hysteresis ON-OFF type controllers and the oscillations introduced by them have to be cancelled out by the outer speed loop controller (which is usually a PI speed controller and whose performance is good around the global operating points and for relatively small variations of the external parameters and disturbances caused in particular by the load torque variation), while retaining the advantages of the DTC strategy, this paper presents the improvement of the performance of the PMSM sensorless control system using Proportional Integrator (PI), PI Equilibrium Optimizer Algorithm (EOA), Fractional Order (FO) PI, Tilt Integral Derivative (TID) and FO Lead-Lag for constant flux, and Sliding Mode Control (SMC) and FOSMC for variable flux. The performance indicators of the control system are the usual ones: response time, settling time, overshoot, steady-state error and speed ripple, plus another one given by the fractal dimension (FD) of the PMSM rotor speed signal, and the hypothesis that the FD of the controlled signal is higher when the control system provides better performance is verified. The paper also presents the basic equations of the PMSM, based on which the synthesis of integer and fractional controllers, the synthesis of an observer for estimating the PMSM rotor speed, electromagnetic torque and stator flux are presented. The comparison of the performance of the proposed control systems and the demonstration of the parametric robustness are performed by numerical simulations in Matlab/Simulink using Simscape Electrical and Fractional Order Modelling and Control (FOMCON). Real-time control based on an embedded system using a TMS320F28379D controller demonstrates the good performance of the PMSM sensorless control system based on the DTC strategy in a complete hardware-in-the-loop (HIL) implementation.

As the adoption of renewable energy sources grows, ensuring a stable power balance across various time frames has become a central challenge for modern power systems. In line with the "dual carbon" objectives and the seamless integration of renewable energy sources, harnessing the advantages of various energy storage resources and coordinating the operation of long-term and short-term storage have become pivotal directions for future energy storage deployment. To address the complexities arising from the coupling of different time scales in optimizing energy storage capacity, this paper proposes a method for energy storage planning that accounts for power imbalance risks across multiple time scales. Initially, the Seasonal and Trend decomposition using the Loess (STL) decomposition method is utilized to temporally decouple actual operational data. Subsequently, power balance computations are performed based on the obtained data at various time scales to optimize the allocation of different types of energy storage capacities and assess the associated imbalance risks. Finally, the effectiveness of the proposed approach is validated through hourly applications using real-world data from a province in China over recent years.

Aortic valve stenosis and malignancy frequently coexist and share the same risk factors as atherosclerotic disease. Data reporting the prognosis of patients with severe aortic stenosis and cancer are limited. Tailoring the correct and most optimal care for cancer patients with severe aortic stenosis is complex. Cancer patients may be further disadvantaged by aortic stenosis if it interferes with their treatment by increasing the risk associated with oncologic surgery and compounding the risks associated with cardiotoxicity and heart failure (HF). Nowadays, several therapeutic options are available for aortic valve stenosis (surgical valve replacement , transcatheter valve implantation, balloon valvuloplasty, or medical therapy), but in presence of malignancy, the use of one of these versus the others should be decided on a case-by-case approach, depending on cancer stage and associated treatment, expected outcome, comorbidities and after an accurate physical examination and Doppler-echocardiography which are the key tools for diagnosing and evaluating aortic stenosis. The current review considers the available data on the association between aortic stenosis and cancer, and therapeutic options.

(1) Background: To identify the association between the presence or absence of raphe and aortic valve dysfunction as well as the presence of aortopathy in patients with bicuspid aortic valve (BAV); (2) Methods: This retrospective study enrolled 312 participants (mean [SD] age, 52.7 [14.3] years; 227 men [72.8%]) with BAV. The BAVs were divided into those with presence (raphe+) or absence (raphe-) of raphe. Valvular function was classified as normal, aortic regurgitation (AR), or aortic stenosis (AS) using TTE. The pattern of BAV aortopathy was determined by the presence of dilatation at the sinus of Valsalva and the middle ascending aorta using CCT.; (3) Results: BAVs with raphe+ had a higher prevalence of AR (148 [79.5%] vs. 48 [37.8%], P < .001) but a lower prevalence of AS (90 [48.6%] vs. 99 [78.0%], P < .001) compared with those with raphe-. The types of BAV aortopathy were significantly different (P = 0.021) according to those with BAV-raphe+ and BAV-raphe-.; (4) Conclusions: The presence of a raphe was significantly associated with a higher prevalence of AR but a lower prevalence of AS and combined dilatation of the aortic root and middle ascending aorta. The presence of raphe was an independent determinant of AR.

The presence of anti SARS-CoV2-RBD antibody (Anti-RBD) prevents severe COVID-19. We aimed to determine the accuracy of a point-of-care Anti-RBD test implemented in person living with HIV (PLWH), systemic lupus erythematosus (SLE), and chronic kidney disease (CKD). We enrolled 182 non-comorbid subjects and 335 persons with comorbid (PLWH, SLE, CKD) to test anti-RBD assay compared to surrogate viral neutralization (SVNT) as the reference test. We performed linear correlation analysis between anti-RBD vs SVNT and a ROC analyses to ascertain anti-RBD cut-off at 30%, 60%, and 90% inhibition of SVNT to calculate accuracy. Correlations of anti-RBD to SVNT among all groups were excellent with R= 0.7903, R=0.7843, R=0.8153 among non-comorbid, SLE and CKD groups, respectively, with significantly higher correlation among the PLWH group (R=0.8877; p-value=0.0072) compared to non-comorbid group. The accuracy of the anti-RBD test among PLWH and CKD group was similar with the non-comorbid but showed lower sensitivity in the SLE group (p=0.000014). The specificity of the test remained high in all groups. In conclusion, the Anti-RBD test had excellent correlation to SVNT. The persistently high specificity in all groups suggests that this test can be reliably utilized to detect presence of low neutralization capacity, prompting additional vaccination.

The automotive market is very competitive and presents a demand for the consistent improvement of the used technologies and reduction of the product cost and dimensions with each product model iteration. Hence, it is important to have access to well-defined reference designs of high quality products, in order to evaluate the new ideas and technologies. This paper provides the readers with a numerical model of such a high quality product, i.e., the IPMSM type traction motor from the 4th generation of the Toyota Prius hybrid transaxle. In the introductory section, the brief history of the Prius model is given together with the references to the reverse engineering reports. Afterwards, the machine dimensions, material properties and winding configuration are described. Then, the model is validated with the torque measurements at constant speed. In the next chapters the simulation results are presented and the numerical source data are supplied to the reader. Finally, the design philosophy of the Toyota drive is briefly discussed in comparison with the BMWi3 drive and the results are concluded in the last section.

In a V2V communication environment, the control of electric vehicle platoons faces issues such as random communication delays, packet loss, and external disturbances, which affect sustainable transportation systems. In order to solve these problems and promote the development of sustainable transportation, a longitudinal control algorithm for the platoon based on robust Unscented Kalman Filter (UKF) and Model Predictive Control (MPC) is designed. First, a longitudinal kinematic model of the vehicle platoon is constructed, and discrete state-space equations are established. The robust UKF algorithm is derived by enhancing the UKF algorithm with Huber-M estimation. This enhanced algorithm is then used to estimate the state information of the leading vehicle. Based on the vehicle state information obtained from the robust UKF estimation, feedback correction and compensation are added to the MPC algorithm to design the robust UKF-MPC longitudinal controller. Finally, the effectiveness of the proposed controller is verified through CarSim/Simulink joint simulation. The simulation results show that in the presence of communication delay and data loss, the robust UKF-MPC controller outperforms the MPC and UKF-MPC controllers in terms of MSE and IAE metrics for vehicle spacing error and acceleration tracking error, and exhibits stronger robustness and stability.

Modern building automation systems implement plenty of advanced control and monitoring functions considering various parameters like users’ activity, lighting, temperature changes etc. Moreover, new solutions based on Internet of Things and cloud services are also being developed for smart buildings to ensure comfort of use, user safety, energy efficiency improvements and integration with smart grids and smart city platforms. Such a wide spectrum of technologies and functions requires a new approach in building automation systems design to provide effective way of their implementation and flexibility during operation. At the same time, in the building design and operation industries, tools based on building information modeling and digital twins are being developed. In this paper, the authors discuss development directions and application areas of these solutions, identifying new trends and possibilities of their use in smart homes and buildings. In particular, the focus is on procedures for selecting automation functions, effective integration, and interoperability of building management systems with Internet of Things considering organization of prediction mechanisms and dynamic functional changes in buildings and smart networks. Chosen solutions and functions should consider the requirements from EN ISO 52120 standard and the guidelines defined for the Smart Readiness Indicator.

Crowd abnormal behavior recognition is one of the research hotspots in computer vision. Its goal is to use computer vision technology and abnormal behavior detection models to accurately perceive, predict, and intervene in potential abnormal behaviors of the crowd, and monitor the status of the crowd system in public places in real-time, to effectively prevent and deal with public security risks and ensure public life safety and social order. To this end, focusing on the crowd abnormal behavior recognition technology in the computer vision system, a systematic review study of its theory and cutting-edge technology is conducted. First, the crowd level and abnormal behaviors in public places are defined, and the challenges faced by crowd abnormal behavior recognition are expounded. Then, from the dimensions based on traditional methods and based on deep learning, the mainstream technologies of abnormal behavior recognition are discussed, and the design ideas, advantages, and limitations of various methods are analyzed. Next, the mainstream software tools are introduced to provide a comprehensive reference for the technical framework; Secondly, typical abnormal behavior datasets at home and abroad are sorted out, and the characteristics of these datasets are compared in detail from multiple perspectives such as scale, characteristics and uses, and the performance indicators of different algorithms on the datasets are compared and analyzed; Finally, the full text is summarized and the future development direction of crowd abnormal behavior recognition technology is prospected.

In new Guideline for the Management of Patients with Valvular Heart Disease for tricuspid regurgitation (TR) is focused the importance of measurement of right-sided diastolic pressures and right ventriculography, pulmonary artery pressures, and pulmonary vascular resistance. Assessment of right ventricular (RV) dimensions and function is pivotal to select patients with severe tricuspid regurgitation who may benefit from tricuspid valve intervention. However, with the exception of tricuspid valve annulus diameter, there is no other cut-off value that defines severe RV dysfunction or dilation for this specific group of patients. It may be difficult, if not impossible, to establish a cut-off value of RV dysfunction since the RV may be exposed to pressure and volume overload, myocardial ischemia, intrinsic myocardial disease or pericardial constraint. Furthermore, the response of the RV to tricuspid valve intervention may vary according to each aetiology and the time course of the disease (acute or chronic). Comprehensive assessment of RV function should address in shape remodelling; functional remodelling; tissue remodelling. This assessment should be performed in optimal loading conditions and after euvolemia has been achieved. It’s now that there is no other cut-off value that defines severe RV dysfunction or dilation for patients with severe TR with the exception of tricuspid valve annulus diameter. It may be difficult, if not impossible, to establish a cut-off value of RV dysfunction since the RV may be exposed to pressure and volume overload, myocardial ischemia, intrinsic myocardial disease or pericardial constraint. In this review we analyze the relationship between right ventricular (RV) and TR in term of outcomes and mortality predictor in patients undergoing percutaneous or invasive treatment for severe TR.

Water samples for bacterial microbiome studies undergo a biomass concentration, DNA extraction and taxonomic identification steps. Through benchmarking, we studied the applicability of Skimmed milk flocculation (SMF) for bacterial enrichment, an adapted in-house DNA extraction protocol, and six 16S rRNA databases (16S-DBs). Surface water samples from two rivers were treated with SMF and Vacuum filtration (VF) and subjected to amplicon or shotgun metagenomics. A mock community standard underwent five DNA extraction protocols, taxonomical identification with six different 16S-DBs and evaluated by the Measurement Integrity Quotient (MIQ) score. In SMF samples, the skimmed milk was metabolized by members of lactic acid bacteria or genera such as Polaromonas, Macrococcus, and Agitococcus, resulting in increased relative abundance (p &lt; 0.5) up to 5.0 log fold change compared to VF, rendering SMF inapplicable for bacterial microbiome studies. The best performing DNA extraction protocols were FastSpin Soil, the in-house method and EurX. All 16S-DBs yielded comparable MIQ scores within each DNA extraction kit, ranging from 61-66 (ZymoBIOMICs) up to 80-82 (FastSpin). DNA extraction kits exert more bias to the composition than the 16S-DBs. This benchmarking study presented valuable insights to inform future water metagenomic study designs.

Water quality assessment in pastoral of Tibetan Plateau, which is water sources for about 40% of world's population and the runoff-yield area of Yellow rivers, is very important. In this paper, Xiahe county which belongs to Tibetan Plateau pastoral was investigated. Six parameters(via, chloride, COD, ammonia nitrogen, nitrate, fluoride, sulfate) were selected to assess the water quality and health degree by using fuzzy comprehensive evaluation methods. The hydrochemical type in surface water was of HCO3--Mg2+-Ca2+ type. The cations and anions in surface water were mainly from weathering and dissolution of carbonate rock. Results showed that the water quality in all 69 sampling sites was all of class Ⅰ. The integrated health degree reached more than 0.85 and the health rate were 100%. Although ammonia nitrogen was regarded as the main contamination factor, but it had a little effect on the entire body of water. Overall, the surface water qualities of most samples in Xiahe County was good condition.

Ensuring precise electric locomotive stopping is pivotal for achieving intelligent and unmanned auxiliary transportation systems. Currently, human drivers' expertise plays a central role in the stopping process, posing challenges for automation and cargo location accuracy, particularly in coal mining. This paper focuses on achieving accurate electric locomotive stopping under diverse conditions by utilizing permanent magnet synchronous motor-driven locomotives. This technique introduces a novel stopping control method that combines a fuzzy Proportional-Integral-Derivative (F-PID) controller and a vector control model for permanent magnet synchronous motors (PMSM). After this, we design the F-PID using the PMSM technique based on the new fuzzy rules for each sub-system. In the end, extensive simulations and real-world experiments are conducted on an electric locomotive stopping test bed, which demonstrate the effectiveness of the proposed control method. From the simulation results, it confirming that the ability to achieve precise stopping under various working conditions.

The development and utilization of wind energy is of great significance to the sustainable development of China's economy and the realization of the goal of "dual carbon". Under the typhoon system, the randomness and volatility of wind speed become an important basis for affecting the energy efficiency utilization and design of wind turbines. Therefore, based on wind speed and wind direction data at 10m, 30m, 50m and 70m heights of a wind power tower in Yancheng, Jiangsu Province, this paper analyzes the change characteristics of wind speed and wind direction by using BFAST method and Hurst index. Based on typhoon body data, topographic data and mesoscale system wind direction data, the causes of the occurrence and development of wind speed and wind direction of wind tower are further analyzed, and a conclusion is drawn: (1) In BEAST method, there are 5, 5, 6 and 6 change points at the height of 10m, 30m, 50m and 70m respectively. Among them, the change points at the height of 10m, 30m and 50m all change before and after node 325, and the change time point at the height of 70m is inconsistent with other heights. Hurst index results show that the inconsistency at 70m altitude is stronger than that at other altitudes. (2) The wind direction sequence at 10m, 30m, 50m and 70m altitude is fitted by stages, and the direction of wind direction is SE-E-SE-SW-W-NW, where, At the height of 70m, the deviation of the fitting trend line from other altitudes is larger in the wind speed strengthening stage and weakening stage. (3) The wind speed at the height of 10m and 70m has different response degrees to the typhoon body. The correlation between the wind speed and the distance between the wind measurement tower and the typhoon near the center is stronger at the height of 10m than at the height of 70m. The surface type and the wind direction of the mesoscale system also have certain effects on the wind speed and direction. In this paper, the change characteristics and influencing factors of wind speed and direction of wind tower are studied, which provides methods and theoretical support for the study of short-term wind speed when typhoon passes through, and provides reliable support for the selection of wind power forecast indicators and the selection and design of wind turbines under extreme gale weather systems.

Background: The association of echocardiographic findings and subsequent risk of left-sided native valve endocarditis (LS-NVE) is undefined. The aim of this study was to determine if transthoracic echocardiographic (TTE) measurements are associated with the subsequent development of LS-NVE in patients without cardiac predisposing conditions. Methods: Institutional databases were evaluated for adults diagnosed with LS-NVE from 2008 to 2020. Patients with prosthetic valves, cardiovascular implantable electronic devices, intracardiac devices, injection drug use, and predisposing cardiac conditions were excluded. Only patients who had a TTE performed 6 months to 3 years before the development of LS-NVE were included as cases. Controls were patients within the same Mayo location with a TTE report and were matched in a 1:3 ratio according to age, gender, Charlson Comorbidity Index, and echocardiography date. Results: There were 148 cases and 431 matched controls. As compared to controls, IE cases had a higher prevalence of diabetes mellitus (46.6% vs. 30.4%) and chronic kidney disease (46.6% vs. 28.1%) (p<0.001). Left ventricular outflow tract velocity (p=0.017), left ventricular ejection fraction (p=0.018), and E: e’ ratio (p=0.050) were associated with LS-NVE. Conclusions: Echocardiographic measurements were associated with subsequent LS-NVE development in this pilot study. A larger cohort of LS-NVE patients, however, is needed to validate these findings.

The detection, characterization, and monitoring of SARS-CoV-2 recombinant variants is a challenge to public health authorities worldwide. Recombinant variants, composed of two or more SARS-CoV-2 lineages, often have unknown impacts on transmission, immune escape, and virulence in the early stages of emergence. We examined 4,213 SARS-CoV-2 recombinant SARS-CoV-2 genomes collected between 2020 and 2022 from California to describe regional and statewide trends in prevalence. Many of these recombinant genomes, such as those belonging to the XZ lineage, or novel recombinant lineages, likely originated within the state of California. We discuss the challenges and limitations surrounding Pango lineage assignments, the use of publicly available sequence data, and adequate sample sizes for epidemiologic analyses. Although these challenges will continue as SARS-CoV-2 sequencing volumes decrease globally, this study enhances our understanding of SARS-CoV-2 recombinant genomes to date while providing a foundation for future insights into emerging recombinant lineages.

This paper Numerically investigates the effectiveness of the turbine rotating blade nozzle position on the vortex and film composite cooling performance. The coolant injecting nozzles arranged near the pressure surface side (PS-side-in) .vs. arranged near the suction surface side (SS-side-in) are compared at the rotating speed range of 0-4000rpm with fluid and thermal conjugate approach. Results show that the nozzle position presents different influences under low and higher rotating speed. In terms of the mainstream flow, rotation makes the stagnation line move from the PS-side pressure surface side to the SS-side suc-tion surface side, which changes the coolant film attachment on the blade leading edge surface. The nozzle position however indicates limited influence on the coolant film flow. In terms of the internal channel vortex flow, the coolant injecting from the nozzles forms a high-velocity region near the target wall which brings about enhancing convective heat transfer. The direction of the near wall vortex flow is opposite and align to the Coriolis force direction in both the PS-side-in and SS-side-in, respectively. Therefore, the Coriolis force augments to the heat transfer of the internal vortex cooling in SS-side-in while weakens the internal heat transfer in PS-side-in. Such effects become more intense with higher rotational speed. The blade surface area-averaged dimensionless temperature that inversely proportional to the actual temperature is 7.8% higher in SS-side-in as compared to that in PS-side-in. The SS-side-in suggests more superior composite cooling perfor-mance under the relatively higher rotating speed.

Gut bacteria play an important role in several metabolic processes and human diseases, such as obesity and its co-morbidities, like fatty liver disease, insulin resistance/diabetes and cardiovascular events. Among several factors, dietary patterns, probiotics, prebiotics, synbiotics, antimicrobials and non-dietary factors, such as stress, age, exercise and climatic conditions, can dramatically impact the human gut microbiota diversity and equilibrium. However, the effect of minor food constituents, including food additives and trace contaminants, on human gut microbiota has received less attention. Consequently, the present review aimed to provide an objective perspective of the current knowledge regarding the impacts of minor food constituents on human gut microbiota and consequently, on human health.

The essence of cross-modal generation and retrieval modeling for image-text interactions lies in semantic consistency. Among these, cross-modal representation alignment serves as the foundational requirement for achieving cross-modal semantic consistency. The crux of our proposed method entails the collaborative training of an image captioning model(referred to as the ’captioner’) and a pair of contrastive encoders for image-text matching(referred to as the ’concoder’). This synergistic approach yields concurrent enhancements in concoder’s performance, captioner’s proficiency, and cross-modal semantic coherence. We coin the proposed method as ‘ReCap’. To begin, we initialize the concoder through knowledge distillation from a pre-trained model. During the training process, we use the output of the initialized concoder as input to a residual attention network, jointly training it with the captioner to achieve semantic consistency. Subsequently, we iteratively update the concoder during the image-text momentum encoding phase using the residual attention network, creating a closed-loop for semantic consistency resolution. Upon completion of training, the concoder and captioner modules can be used independently to perform tasks related to cross-modal retrieval and cross-modal generation of text and images. In order to substantiate the efficacy of our proposed method, we initially conducted empirical experiments encompassing image-text retrieval and image captioning tasks, employing a widely recognized benchmark dataset, MSCOCO. Subsequently, we assessed the fine-grained cross-modal alignment performance of the concoder through an image classification task on the iNaturalist 2018 dataset. The achieved performance metrics notably surpassed those achieved by several incumbent state-of-the-art models, thus validating the proficiency of our method. Finally, motivated by the practical requirements of handling the nature conservation image data, we performed caption annotation for the iNaturalist 2018 dataset. Subsequently, we trained the ReCap on this annotated data. Experimental results demonstrate that our proposed method can maintain semantic consistency between cross-modal retrieval and image caption generation for species with similar visual features but distinct semantics. This achievement signifies a meaningful exploration in the field of cross-modal semantic consistency representation, holding significant practical value in the domain of biological research.

The weight coefficients of the diaphragm spring depend on experiences in the traditional optimization. However, this method not only cannot guarantee the optimal solution but it is also not universal. Therefore, a new optimization target function is proposed. The new function takes the minimum of average compress force changing of the spring and the minimum force of the separation as total objectives. Based on the optimization function, the result of the clutch diaphragm spring in a car is analyzed by the non-dominated sorting genetic algorithm (NSGA-II) and the solution set of Pareto is obtained. The results show that the pressing force of the diaphragm spring is improved by 4.09%by the new algorithmand the steering separation force is improved by 6.55%, which has better stability and steering portability. The problem of the weight coefficient in the traditional empirical design is solved. The pressing force of the optimized diaphragm spring varied slightly during the abrasion range of the friction film, and the manipulation became remarkably light.

The Tesla valve (TV), a valvular conduit invented by Nicola Tesla over a decade ago, has recently gained significant attention and application in various fields due to the growing interest in microfluidics and nanofluidics. The unique architecture of TV characterized by an asymmetrical design and an arc-shaped channel, has long been an intriguing yet underrated design for building a passive component in a microfluidic system. While previously regarded as a technology without significant use, TV structures have been implemented in wearable devices, thermal manipulation fluidics, micromixers, micropumps, and fuel cell devices. This article presents the first comprehensive review of TV structures in the literature, which has seen significant growth in the last two years. The review discusses typical TV structures, including single-stage TV (STV), multistage TV (MSTV), and TV derivatives (TVD), along with their characteristics and potential applications. The designs of these structures vary based on their intended applications, but all are constructed based on the fundamental principle of the TV structure. Finally, future trends and potential applications of TV structures are summarized and discussed. This review provides a valuable reference for students, early-career scientists, and practitioners in the field of fluidic devices, particularly those interested in using TV structures as passive components.

Nowadays energy saving is a topical issue due to increasing fuel costs and this aspect is amplified by more stringent emissions regulations that impact on vehicle development. A recent study conducted by the U.S. Department of Energy shows that about five percent of the U.S. energy consumption is transmitted by fluid power equipment. Nevertheless, this study also shows that the efficiency of fluid power averages 21 percent. This offers a huge opportunity to improve the current state-of-the-art of fluid power machines, in particular to improve the energy consumption of current applications. These facts dictate a continuous strive toward improvements and more efficient solutions: to accomplish this objective a strong reduction of hydraulic losses and better control strategies of the hydraulic systems are needed. In fluid power, there exist many techniques to reduce/recover energy losses of the conventional layouts, e.g. load sensing, electrohydraulic flow matching, independent metering, etc. One of the most efficient ways to analyze these different layouts and identify the best hydraulic solution is done through virtual simulations instead of prototyping, since the latter involves higher investment costs to deliver the product into the market. However, to build a fluid power machine virtual model, some problems arise relative to different aspects, for instance: loads on actuators (both linear and rotational) are not constant and pumps are driven by a real engine whose speed depends on required torque. Furthermore, it is important to achieve higher level of detail to simulate each component in the circuit: the greater detail, the better the machine behavior is portrayed, but it obviously entails heavy impact on simulation time and computational resources. Therefore, there is a need to create mathematical model of components and systems with sufficient level of detail to easily acquire all those phenomena necessary to correctly evaluate machine performance and make modifications to the fluid power component design. In this context, a hydraulic proportional valve PVG 32 by Danfoss is taken as an object of study, its performance is analyzed with suitable mathematical model and simulation is done to observe closeness of a model to the laboratory experiment.

This paper proposes a position control method for low cost EGR valve system in automotive application. Generally, position control system using in automotive application has many restrictions such as cost and space, the mechanical structure of actuator implies high friction and large difference between static friction and coulomb friction. This large friction difference occurs the vibrated position control result when the controller uses conventional linear controller such as P, PI. In this paper, low cost position control method which can apply under the condition of high difference friction mechanical system. Proposed method is verified by comparing conventional control result of experiments.

The paper introduces a control hybrid model that is designed on the basis of OOSEM (Object-Oriented Systems Engineering Method), MDA (Model-Driven Architecture) concepts, RealTime UML/SysML (Unified Modeling Language/Systems Modeling Language), and an algorithm based on UKF (Unscented Kalman Filter). This hybrid model enables the implementation of control elements for autonomous underwater vehicles (AUVs) and can be adapted to reuse for most standard AUV platforms. To obtain this goal, the dynamic model of AUV is integrated with the following specializations of OOSEM/MDA, in which the analysis model is clarified via the use-case model definition and then combines with HA (hybrid automata) to precisely define the requirements for control. Next, the designed model is specialized via real-time UML/SysML to get the core control blocks, which describe the behaviors and structures of control parts in detail. This design model is then transformed into the model of implementation with the assistance of round-trip engineering to conveniently realize the controller of AUVs. Based on this new model, an AUV controller for low-cost turtle-shaped AUVs is implemented that performs tracking for a planar trajectory with accepted feasibility.

The working environment of mining electric locomotives is wet and muddy coal mine 1 roadway. There may be idling or slipping between the wheels and rails of mining electric locomotives 2 due to low friction between the wheel and rail and insufficient utilization of creep rate. Therefore, it 3 is necessary to control the creep rate within a reasonable range. In this paper, the autonomous control 4 algorithm for mining electric locomotives based on improved ε-greedy is theoretically proven to be 5 convergent and effective firstly. Secondly, after analyzing the contact state between the wheel and rail 6 under wet and slippery road conditions, it was concluded that the value of creep rate is an important 7 factor affecting the autonomous driving of mining electric locomotives. Therefore, the autonomous 8 control method for mining electric locomotives based on creep control is proposed in this paper. 9 Finally, the effectiveness of the proposed method was verified through simulation. The problem of 10 wheel slipping and idling caused by insufficient friction of mining electric locomotives in coal mining 11 environments is effectively suppressed. Autonomous operation of vehicles with optimal driving 12 efficiency can be achieved through quantitative control and utilization of the creep rate between 13 wheels and rails

There is increasing evidence that some adult mitral valve pathologies may have developmental origins involving errors in cell signaling and protein deposition during valvulogenesis. While early and late gestational stages are well-documented in zebrafish and small mammalian models, longitudinal studies in large mammals with a similar gestational period to humans are lacking. Further, the mechanism of chordae tendineae formation and multiplication remains unclear. This current study presents a comprehensive examination of mitral anterior leaflet and chordae tendineae development in a bovine model (with a gestational period of 9 months). Remarkably distinct from small mammals, bovine development displayed early branched chordae, with increasing attachments only until birth, while the anterior leaflet grew both during gestation and postnatally. Chordae also exhibited accelerated collagen deposition, maturation, and crimp development during gestation. These findings suggest that the bovine anterior leaflet and chordae tendineae possess unique compartmentalized processes of development despite being a continuous collagenous structure.

Anthropogenic development can strongly influence natural river processes, leading to environmental changes that negatively affect important habitats and biodiversity, and consequently reduce economically important natural resources. This study investigated the effects of salinity intrusion on the habitat of the clam Corbicula japonica in the Seomjin River estuarine zone. We employed the Environmental Fluid Dynamics Code (EFDC) model, which incorporates topographic data and hydrological changes, to simulate salinity concentrations. Two salinity measurement facilities were installed in Seomjin River estuarine and operated to optimize the EFDC model. The results show that reduced flow rates due to intake have a negligible impact on the increased salinity. Maintaining optimal salinity (15–20 psu) during neap tides at the Seomjin River Bridge requires constant high flow rates, which poses significant challenges. Saltwater stratification is identified as the primary cause of pronounced salinity stratification, particularly during neap tides. Addressing this issue through river discharge and intake facility operation is challenging. Structural measures, including riverbed restoration and underwater barriers, are recommended to improve resistance to seawater intrusion. Future research should aim to develop scenarios to reduce salinity concentrations, quantify the reduction efficiency, and propose region-specific measures.

The Stellarator Power Plant Studies Prospective R&amp;D Work Package among the Eurofusion Programme was settled to bring the stellarator engineering to maturity, so that stellarators and particularly the HELIAS (HELical-axis Advanced Stellarator) configuration could be a possible alternative to tokamaks. However, its complex geometry makes designing a Breeding Blanket (BB) that fully satisfies the requirements for such an HELIAS configuration a difficult task. Taking advantage of the acquired experience in BB design for DEMO tokamak, CIEMAT is leading the development of a Dual Coolant Lithium Lead (DCLL) BB for a HELIAS configuration. To answer the specific HELIAS challenges new and advanced solutions have been proposed, as the use of fully detached First Wall (FW) based on liquid metal Capillary Porous Systems (CPS). These proposed solutions have been studied in a simplified 1D model that can help to estimate the relative variations in Tritium Breeding Ratio (TBR) and displacement per atom (dpa) to verify their effectiveness to simplify the BB integration, improve the machine availability while keeping the main BB nuclear functions (i.e. tritium breeding, heat extraction and shielding). This preliminary study demonstrates that the use of FW CPS would reduce the radiation damage received by the blanket without compromising its tritium breeding performance.

In this paper, an adaptive proportional and integral (PI) controller for speed control of electric drives is developed. The adaptive PI controller is designed based on model reference adaptive identification and the Lyapunov function so that the system stability can be proved. To identify the inertia, the viscous friction torque coefficient, and the load torque simultaneously and smoothly, sinusoidal speed reference is usually employed. A modified motion equation considering the low-pass filter for feedback speed and the Coulomb friction torque is introduced and the relationship between the identified parameters and their actual values are clarified. A high-precision digital simulation model is built based on MATLAB/Simulink. The effectiveness of the proposed method is verified by simulations under various conditions.