This research article investigates the recycling of end-of-life solar photovoltaic (PV) panels by analyzing various mechanical methods, including Crushing, High Voltage Pulse Crushing, Electrostatic Separation, Hot Knife Cutting, Water Jet Cutting, and Magnetic Separation. Each method's effectiveness in extracting materials such as glass, silicon, metals (copper, aluminum, silver, tin, lead), and EVA was evaluated. The analysis reveals that no single method is entirely sufficient for comprehensive material recovery. Based on the data analysis, a new hypothetical hybrid method Laser and High Voltage Pulse (L&HVP) is proposed, which integrates the precision of laser irradiation with the robustness of high voltage pulse crushing. The laser irradiation step would theoretically facilitate the removal of the ethylene-vinyl acetate (EVA) encapsulant, preparing the materials for subsequent separation. The high-voltage pulse crushing would then selectively fragment and separate the remaining components, potentially enhancing material recovery efficiency while minimizing contamination. The proposed approach is grounded in the observed limitations of existing techniques. This method aims to offer a more comprehensive and sustainable solution for solar PV module recycling. Further research and experimentation are necessary to validate the effectiveness of the L&HVP method and its potential impact on the field of solar PV recycling.

Composites, and especially carbon fiber reinforced plastics (CFRPs), are increasingly used in the automotive, aerospace, and aviation industries, and as a result, CFRP production has increased dramatically, leading to a corresponding increase of waste. Landfill and incineration of waste are likely to be restricted as a result of the legislation, thus highlighting the need for efficient recycling methods for CFRPs. However, the recycling of CFRP is very challenging, mainly due to the difficulty of removing the thermosetting matrix. This study reports a pre-screening of the solvolysis recycling process for CFRPs based on the mechanical properties of the recovered fibers. To this end, solvolysis tests were conducted on unidirectional CFRP samples under supercritical and subcritical conditions using acetone and water. The solvolysis tests were conducted for various conditions of temperature, pressure, and reaction time. The efficiency of the recycling processes has been evaluated through a morphological and a mechanical characterization of the recovered fibers. In most cases, the decomposition efficiency of the epoxy resin, measured in terms of mass, ranged between 90 and 100%. Moreover, the scanning electron microscopy images of the recovered fibers showed negligible traces of resin residues and no detectable signs of physical damage or any changes in morphology with regard to diameter. Finally, the single-fiber tension tests revealed that that the recovered fibers retained more than 61% of their initial Young's modulus and 70% of their tensile strength.

Recycling of composite materials has become a very important topic to develop sustainable solutions for the management of waste generated by industries that use composite materials. This paper presents a bibliographical review on the main recycling methods of composite materials such as: mechanical, chemical, thermal and hybrid. In mechanical recycling, the material is crushed or ground, generally using the resulting material as filler, which causes limitations in the applications due to the type of resulting fibers (short, long, non-uniform). On the other hand, chemical recycling breaks down polymers through a chemical reaction and recovers fibers, so in some cases the mechanical properties of the fibers are affected. Thermal recycling uses high temperatures to break down materials, transforming them into energy or reusing them in other products. Finally, hybrid recycling uses two or more processes as a means to recover the material; among the most used methods in this category is the mechanical process combined with the thermal process. This review describes the advantages and disadvantages of each method, as well as the environmental impact. Although each type of recycling offers special characteristics for the material obtained, it is necessary to continue researching and developing technologies for recycling processes that promote recycling and reuse of composite materials in a better way.

Mechanical recycling of solid plastic wastes on a small-scale level can be accomplished with the correct approaches. Thermoplastics are mostly considered for mechanical recycling because of their physical properties and ease of reprocessing. This paper reviews the mechanical reprocessing techniques of selected thermoplastics (polyethylene terephthalate and polyolefins) since they constitute a significant proportion of plastics used commercially. Furthermore, necessary considerations for effective operation of small-scale plants, including energy requirements of machinery and optimisation in order to improve efficiency and product quality, are discussed. A clearer understanding and addressing of the process-related challenges will lead to successful establishment and management of small-scale mechanical recycling facilities to benefit communities. Efficient small-scale mechanical reprocessing establishments have become essential in reducing the environmental impacts of solid plastic wastes and for energy conservation.

Mechanical response of bisphenol-F based epoxy cured with amine hardener was investigated in tensile testing. Different types of methods were considered in preparing the tensile samples in order to evaluate their effects on the tensile strength of the cured epoxy system. Specifically, four types of preparation methods were discussed to prepare the tensile samples were considered in the study. Further, the effect of different type of tensile samples on tensile strength of specimens was also considered in the analysis. The experimental results showed that the preparation methods affected the tensile strength of the specimens. Starting from the experimental results, an appropriate testing methodology is proposed for epoxy based nanocomposite composite specimens in order to reduce problems that may arise during the test and to optimize procedures for preparation of specimens.

The development in the field of ceramics has been increasing over the past several decades. Among all of the dental ceramics, zirconia ceramics show very good mechanical properties and a significant improvement in mechanical function. However, it is properly established that each step of the fabrication process of zirconia ceramics must be controlled to achieve the expected mechanical properties. These steps include the block constructing, sintering process, machining and surface processing. Recent advances have focused on zirconia ceramics in forming and sintering processes, mechanical properties, combining with various materials, and on surface processing. All these items provide conceptions about the formability and machinability of the zirconia. Until now, very excellent studies have been done to specify the evolution of microstructures, phase and mechanical properties of zirconia ceramics during the sintering process. However, more studies are required in this field. This paper aims to demonstrate general views and various studies in the field of zirconia ceramics. The properties, applications and tests performed and the recent developments in the field of zirconia bioceramics are discussed.

The paper deals with the problems of direct kinematics related to a 2T6R robot, the direct kinematics of the plane mechanism of the robot. The direct kinematics of this proposed new robot help to study the movement, including the dynamic one, to determine the forces in the mechanism and to model the possible trajectories of the final effector point, thus determining the robot's working space and some of its multiple possible uses. Two totally different methods were used to verify the calculation relations, the results obtained by both methods being practically identical. The first method used is an original trigonometric method, and the second is an original geometrically analytical method.

Integrating nanomaterials like carbon nanotubes (CNTs) and iron oxide (Fe₃O₄) into epoxy composites has significant interest due to their potential to enhance mechanical properties. This study evaluates the impact of dispersion quality on the mechanical performance of CNT/Fe₃O₄/Epoxy composites, comparing stirring and sonication methods at three different loadings: 0.1, 0.3, and 0.5 wt.%. Tensile testing revealed that sonicated composites consistently outperformed stirred composites, with a significant increase in elastic modulus and ultimate tensile strength (UTS). However, fracture strain decreased in both composite types compared to pure epoxy, with sonicated composites experiencing a more significant reduction than stirred composites. These results underscore the importance of high-quality dispersion for optimizing mechanical properties.

The increasing environmental concerns related to no-biodegradable plastics have driven the development of biodegradable alternatives derived from renewable resources. Polylactic acid (PLA), a biodegradable polymer known for its favorable mechanical strength and biocompatibility, suffers from brittleness and poor ductility. This study aims to improve the flexibility of PLA by blending it with polycaprolactone (PCL) and polyethylene oxide (PEO). Specifically, thin films were fabricated from neat PLA, PCL, PLA/PCL, and PLA/PEO blends using both electrospinning and solvent casting to investigate the effects of processing methods on their mechanical behavior. The films were characterized using SEM, FTIR, XRD, DSC, uniaxial tensile testing, and water contact angle measurements. The surface morphology of single electrospun fibers was further examined using AFM. We found that electrospun PLA films exhibited higher elongation at break and ultimate strength with a slightly lower Young’s modulus in comparison to its solvent-cast films. FTIR, XRD, and DSC analyses consistently showed that the electrospun PLA films had significantly lower crystallinity compared to their solvent-cast counterparts. Notably, AFM phase imaging revealed that the electrospun PLA fibers exhibited an aligned crystalline structure. Blending PLA with PCL significantly improved elongation at break in electrospun films, which, unlike solvent-cast blends, retained a Young's modulus comparable to electrospun PLA. This improvement is likely due to reduced phase separation and enhanced crystalline alignment. Furthermore, electrospun films of neat PLA, PCL and PLA/PCL blends were more hydrophobic than their solvent-cast counterparts. Although PLA/PEO blends demonstrated enhanced surface hydrophilicity, they exhibited a marked reduction in mechanical properties. Overall, this study demonstrates that electrospinning effectively enhances the flexibility and mechanical performance of PLA-based films by mitigating the effects of poor miscibility in polymer blends and promoting molecular alignment. These findings suggest that electrospinning is a promising processing method for producing PLA-based films with enhanced flexibility and mechanical integrity, without the need for plasticizers or compatibilizers.

The breast holds significant importance in women's lactation process. The breast has diverse tissues such as glandular, Cooper’s ligament, lactiferous ducts, adipose, muscles, and skin with various mechanical properties. Most soft tissues exhibit nonlinear, viscoelastic, and anisotropic mechanical behaviour. Stiffness is one of the commonly used mechanical properties for measuring mechanical behaviour in soft tissues. However, this is typically used in simplifying cases where analysis is limited to within the linear elastic region. Young’s modulus is the prevailing measure for quantifying stiffness in tissues. This systematic review examines commonly used techniques for mechanically characterising breast soft tissues to close the gap in the literature. Additionally, this systematic review summarises the mechanical behaviour of the breast tissues available in the literature and highlights the uncovered areas to understand the mechanical behaviour of breast tissues fully. These include a) more mechanical behaviour studies, allowing more accurate modelling for other applications, b) Viscoelastic analysis studies, and c) mechanical analysis on other breast tissues, such as the lactiferous duct, also known as the milk duct. The data obtained in the review can be used as inputs in computational models to analyse the behaviour of the breast tissues.

The manufacturing method influences the properties of the produced components. This work investigates the influence of manufacturing methods such as fused filament fabrication (3D printing) and injection molding on water absorption, mechanical and thermal properties of the specimens produced from neat biobased poly(lactic acid) (PLA) polymer and poly(lactic acid)/wood composites. Acrylonitrile butadiene styrene (ABS) acts as the reference material due to its low water absorption and good functional properties. The printing layer thickness is one of the factors that affects the properties of a 3D printed specimen. The investigation includes two different layer thicknesses (0.2 mm and 0.3 mm) while maintaining uniform overall thickness of the specimens across two manufacturing methods. 3D printed specimens absorb significantly higher amounts of water than the injection molded specimens, and the increase in the layer thickness of the 3D printed specimens contributes to further increased water absorption. However, the swelling due to water absorption in 3D printed specimens decreases on increased layer thickness. Tensile, flexural and impact properties of all the specimens decrease after water absorption while the properties improve on decreasing the layer thickness. Higher porosity on increasing the layer thickness is the predominant factor. The results from dynamic mechanical analysis and microscopy validate the outcomes.

Modifying surface topography to prevent surface-induced thrombosis in cardiovascular implants allows endothelialization, which is the natural thrombo-resistance of the blood-contacting surfaces and is deemed to be the only long-term hemocompatible material. We have adapted a simulation framework to predict platelet deposition on the modified surface and developed an optimization strategy to promote endothelial retention and limit platelet deposition. Under supraphysiological bulk shear stress, a maximum of 79% linear coverage was achieved. This study concludes that the addition of microtrenches promotes endothelial retention and can be improved through optimal selection of geometric parameters.

Nano Silicon carbide reinforced aluminum (Al/nanoSiC) metal matrix composites are attractive because of their superior properties such as high strength and stiffness, Application of aluminum in technological and structural application is growing steadily. The major limitation for metal matrix nano composites, however, is their propensity to brittle fracture. The new technologies and new materials are two basic aims for companies. In this research, the effect of addition Al/SiC nano particles on microstructure and mechanical properties of pure aluminum has been investigated. Pure aluminum powder and various fractions of SiC particles with an average diameter of 50 nm were milled by a high-energy planetary ball mill to produce nanocrystalline Al–SiC nanocomposite powders. Pressing and sintering applied to consolidate powders to tablet shape. Then the samples were rolled to cylindrical shape. The nano SiC Percentage were 0%, 2.5%, 5%, 7.5%, 10% , 12,5% and 15%. Mechanical tests such as tensile, hardness, fracture toughness and young’s modules measurement carried out to study the mechanical behavior of each alloy. Scanning electron microscopy was used to study the morphology and microstructure of nanocomposite powders and bulk samples. The role of wt% fraction of SiC nanoparticles was investigated. The results shows that the addition of SiC nano particles has significant influence on the microstructure and mechanical properties of composites and usually the optimum properties depends on wt% SiC.

A mechanical ventilation system is a big support for breathing complications, in which an external solution is quite necessary to keep oxygen compensation in the patients. Its knowledge is well widespread and different equipment has been developed. However, they are very expensive and their quantity in medical centers is not sufficient, especially in Peru. Hence, it has been required to develop new methods to provide oxygen by a low cost equipment; Protofy, a research group from Spain, designed one of the first low cost mechanical ventilation systems which was medically validated by its government. In this sense, a redesign of the mechanical ventilation system was carried out according to the local requirements and available technology, a different airbag resuscitator with different properties and geometry, but maintaining its working concept based on a cam compression mechanism. Sensors and a display were added to improve the performance with a control algorithm for the rotation frequency and to show the ventilation curves over time to the medical staff. It was necessary to develop a mathematical model to relate the behavior between ventilation curves for a patient and physical variables of the design, especially in the epidemic COVID 19, that many countries are dealing with at the time research is being conducted. The mechanical ventilation system was redesigned, fabricated, and tested measuring its ventilation curves over time. Results indicate that this redesign provides a sturdy equipment able to work during a longer lifetime than the original. The replicability of the ventilation curves behavior is assured, while the mechanism dimensions are adapted for a particular airbag resuscitator. The mathematical model of the whole system can predict satisfactorily the ventilation curves over time and was used to provide the air pressure, volume, and flow as a function of the rotation angle measured by sensors.

Engineering application of additively manufactured (AM) metallic materials is quite limited by their fatigue behaviors which are very inconsistent with that of conventionally wrought or cast ones. Here, based on advanced material characterization techniques, such as focused ion beam (FIB), scanning electron microscopy (SEM) and transmission electron microscopy (TEM), the mi-crostructures underneath fracture surfaces were thoroughly investigated in an AM aluminium (AlSi10Mg) alloy with horizontal and vertical building orientation endured very-high-cycle fa-tigue (VHCF) loading under stress ratios R = –1, 0 and 0.5. Two VHCF failure specimens A and B were representatively selected to further SEM examine and TEM samples preparation via FIB milling. Specimen A was horizontally printed and failed at R = –1; specimen B was vertically printed and failed at R = 0. TEM samples A1 and B1 were lifted from locations near the crack ini-tiation sites on the fracture surfaces of specimens A and B; The locations of TEM samples A2 and B2 kept away from the crack origin sites but still within the “fish-eye” region of crack steady growth. TEM observations show that there was no characteristic microstructure induced by VHCF in different oriented specimens and under various R values.

The flavor, aroma and color of coffee may change due to mechanical damage, reducing its qual-ity. To measure the mechanical response of materials, compression tests can be performed, de-termining the effect of force application on the mechanical behavior of the fruit at different stages of ripeness. In this context, this study aimed to analyze the deformation, strain energy and equivalent von Mises stress of coffee fruits at mature, semi-mature and immature maturation stages and compressed by collapse forces. Compression in three directions (x, y and z) was sim-ulated on coffee fruit models using the finite element method, with a compression support in the direction opposite to the force application axis. The numerical simulation of the compression process allowed to verify that the more mature the fruit, the greater the associated mean defor-mation (2.20 mm mm-1, 0.78 mm mm-1 and 0.88 mm mm-1), the lower the mean strain energy (0.07 mJ, 0.21 mJ and 0. 34 mJ) and the lower the mean equivalent von Mises stress (0.25 MPa, 1.03 MPa and 1.25 MPa), corresponding to ripe, semi-ripe and immature fruits; and these proper-ties may be used to analyze how processes in the production chain affect the amount of mechan-ical damage.

A new Mg-Zn-Zr-Ca alloy in powder state was obtained via mechanical alloying method, from pure elemental powder. Further, the obtained powder-alloy was processed by selective laser melting (SLM) procedure to obtain 3D printed samples for small biodegradable implants. A series of microstructural, mechanical and corrosion analysis were performed. The SEM analysis of powder-alloy reveal a good dimensional homogeneity, with uniform colored, no agglutinated and almost rounded particles, suitable for selective laser melting procedure. Further, the SLM samples reveal a robust and unbreakable morphology, with a suitable porosity and without undesirable balling effect. The tested Young’s modulus of the SLM samples, of 42 GPa, is close to cortical bone one, of 30 GPa. The corrosion tests performed in PBS (Phosphate-buffered saline) solution show that the corrosion parameters have a satisfactory evolution.

The reinforcing ability of the fillers results in significant improvements in properties of polymer matrix at extremely low filler loadings compared to conventional fillers. In view of this, present review article describes the different methods used in preparation of different rubber nanocomposites reinforced with nanodimensional individual carbonaceous fillers, such as graphene, expanded graphite, single walled carbon nanotubes, multiwalled carbon nanotubes and graphite oxide, graphene oxide and hybrid fillers consisting combination of individual fillers. This is followed by review of mechanical properties (tensile strength, elongation at break, Young modulus, and fracture toughness) and dynamic mechanical properties (glass transition temperature, crystallization temperature, melting point) of these rubber nanocomposites. Finally, Payne and Mullin Effects have also been reviewed in rubber filled with different carbon based nanofillers.

Rubber compounds based on styrene-butadiene rubber, ethylene-propylene-diene-monomer rubber and the combinations of both rubbers were cured with different sulfur and peroxide curing systems. In sulfur curing systems, two type of accelerators, namely N-cyclohexyl-2-benzothiazole sulfenamide, tetramethylthiuram disulfide and combinations of both accelerators were used. In peroxide curing systems, dicumyl peroxide, and combination of dicumyl peroxide with zinc diacrylate or zinc dimethacrylate, respectively were applied. The work was focused on investigation of the curing system composition as well as type of the rubber or rubbers combinations on curing process, cross-link density and physical-mechanical properties of vulcanizates. The dynamic-mechanical properties on the selected vulcanizates were examined, too. The result revealed correlation between the cross-link density and physical-mechanical properties. Similarly, there was recorded certain correlation between cross-linking degree and glass transition temperature. The tensile strength of vulcanizates based on rubbers combinations was higher when compared to that based on pure rubbers, which points out the fact that by rubbers combination, not only the features of both elastomers can be combined, but also improved tensile characteristics can be achieved. When compared to vulcanizates cured with dicumyl peroxide, materials cured with sulfur system exhibited higher tensile strength. By application of co-agents in peroxide vulcanization, the tensile strength overcame the tensile behavior of sulfur cured vulcanizates.

Sulfur, peroxide and combined sulfur and peroxide curing systems were applied for cross-linking of unfilled and carbon black filled rubber compounds based on ethylene-propylene-diene-monomer rubber. The results revealed that the type of curing system influenced the course and shape of curing isotherms. This resulted in the change of curing kinetics of rubber compounds. The cross-link density of vulcanizates cured with combined vulcanization systems was lower than that for vulcanizates cured only in the presence of sulfur or peroxide system. The results revealed good correlation between the cross-link density as well as the structure of the formed cross-links and physical-mechanical characteristics of the materials. It can be stated that by proper combination of vulcanization systems it is possible to modify tensile behavior of vulcanizates in targeted manner. On the other side, dynamical-mechanical properties were found not be significantly influenced by the composition of curing system.

Electrochemical-mechanical interactions, in particular pressure-induced ones, have been identified to be a cause for lithium-plating in lithium-ion cells. Mechanically-induced porosity inhomogeneities in the separator layers due to electrode expansion during charging especially lead to cell internal balancing currents and can cause localized plating. To identify cell-format and cell-material dependent mechanical weak spots, a layer-resolved mechanical simulation of different cell types and cell-material combinations is presented in this work. The simulation results show distinctive layer strain patterns for different cell-types that coincide with localized lithium-plating found in post-mortem cells. Additionally, the effects of cell bracing in battery modules is investigated and a method to mitigate the increased layer strain due to bracing counterforces is proposed that also increases cell energy density for hardcase-type automotive cells.

In vivo, articular cartilage tissue is surrounded by a cartilage membrane, and HP (HP) and compressive strain increases simultaneously with the compressive stress. However, it has been impossible to investigate the effects of simultaneous loading in vitro. In this study, a bioreactor capable of applying compressive stress under HP was developed to reproduce ex vivo the same physical loading environment found in cartilage in vivo. First, a HP stimulation unit was constructed to apply cyclic HP pressure-resistant chamber by controlling a pump and valve. A compression-loading mechanism that can apply compressive stress using an electromagnetic force was implemented in the chamber. The synchronization between the compression and HP units were evaluated and the stimulation parameters were quantitatively evaluated. Physiological HP and compressive strain were applied to the chondrocytes encapsulated in alginate and gelatin gels after applying high HP at 25 MPa, which induced damage to chondrocytes. It was found that compressive stimulation increased the expression of genes related to osteoarthritis. Furthermore, the simultaneous application of compressive strain and HP, which is similar to the physiological environment in cartilage, had an inhibitory effect on the expression of genes related to osteoarthritis. HP alone also suppressed the expression of osteoarthritis-related genes. Therefore, the simultaneous hydrostatic and compressive stress-loading device developed to simulate the mechanical environment in vivo may be an important tool for elucidating the mechanisms of disease onset and homeostasis in the cartilage.

The aim of the present study was to describe and determine changes in the superelastic properties of NiTi archwires after clinical use and sterilization. Ten archwires from five different manufacturers (GAC, 3M, ODS, GC, FOR) were cut in two segments and evaluated using a three-point bending test in accordance with ISO 14841:2006. The centre of each segment was deflected to 3.1mm and then unloaded to 0 N to obtain a load-deflection curve. Deflection at the end of the plateau and forces at 3, 2, 1 and 0.5mm on the unloading curve were recorded. Plateau slopes were calculated at 2, 1 and 0.5mm of deflection. Data obtained were statistically analysed to determine differences (p<0.001). Results showed that the degree of superelasticity and exerted forces differed significantly among brand groups. After three months of clinical use, FOR released a greater force for a longer activation period. GC, EURO and FOR archwires seemed to lose their mechanical properties. GC wires released more force than other brand wires after clinical use. Regarding superelasticity after sterilization, GAC, 3M and FOR wires recovered their properties, while EURO archwires lost more.

Impure and pure casts have collected reasonable attentions over all the world. In this paper, Aluminum (Al) and Copper (Cu) cast alloys are considered to be studied. Multiple impure and pure Al-Cu cast alloys are established under the condition of very high temperatures. Then, all of the established alloys are examined by applying mechanical tests. More specifically, tests of hardness are exploited. Moreover, different quenching conditions are employed and analyzed. These are the water, air and oil. Consistent results are separately obtained for the impure and pure materials.

Polyacrylamide gel electrophoresis (PAGE) is widely used for studying proteins and protein-containing objects. However, it is employed most frequently as a qualitative method rather than a quantitative one. In this paper, we show the feasibility of routine digital image acquisition and mathematical processing of electrophoregrams for protein quantification. Both the well-studied model protein molecules (bovine serum albumin) and more complex real-world protein-based products (casein-containing isolate for sports nutrition), which were subjected to mechanical activation in a planetary ball mill to obtain samples characterized by different protein denaturation degrees, were used as study objects. Protein quantification in the mechanically activated samples was carried out. The degree of destruction of individual protein was shown to be higher compared to that of protein-containing mixture after mechanical treatment for an identical amount of time. The methodological approach used in this study can serve as guidance for other researchers who would like to use electrophoresis for protein quantification both in individual form and in protein mixtures. The findings prove that photographic imaging of gels followed by mathematical data processing can be applied for analyzing the electrophoretic data.

As part of a plethora of global efforts to minimize the negative effects of the SARS-CoV2 (COVID-19) pandemic, we developed two different mechanisms that, after further development, could potentially be of use in the future in order to increase the capacity of ventilators with low-cost devices based on single-use-bag-valve mask systems. We describe the concept behind the devices and report a characterization of them. Finally, we make a description of the solved and unsolved challenges and propose a series of measures in order to better cope with future contingencies.

(1) Background: Mechanical circulatory support (MCS) in myocardial infarction associated cardiogenic shock is subject to debate. This analysis aims to elucidate the impact of MCS timing on patient outcomes, based on data from the PREPARE CS registry.; (2) Methods: PREPARE CS prospective registry included consecutive patients experiencing cardiogenic shock (SCAI Classes C-E) and were referred for cardiac catheterization. Present analysis included a subset, in whom MCS was used and underwent coronary intervention due to myocardial infarction. Patients were categorized into Upfront group versus Procedural group, depending on the timing of MCS introduction in relation to PCI. Endpoint was the in-hospital mortality; (3) Results: In total 71 patients were included. MCS was started prior to PCI in 33 (46%) patients (Upfront), whereas 38 (54%) received MCS during or after PCI initiation (Procedural). Baseline characteristics and hemodynamic parameters were comparable. The Upfront group had a higher utilization of Impella® device compared to extracorporeal membrane oxygenation (67% vs 33%), while the Procedural group exhibited a balanced use (50% vs 50%). Most patients suffered of multi-vessel disease in both groups (82% vs 84%, respectively; p=0.99) and most patients required complex PCI procedure, the latter was more prevalent in the Upfront group (94% vs 71%, respectively; p=0.02). Rates of complete revascularization were comparable (52% vs 34%, respectively; p=0.16). Procedural CPR was significantly more frequent in the Procedural group (45% vs 79%, p<0.05), still in-hospital mortality was similar (61% vs 79%, respectively; p=0.12); (4) Conclusions: Upfront implantation of MCS in myocardial infarction associated CS did not provide in-hospital survival benefit.

Knee joint injuries, including those affecting the anterior cruciate ligament (ACL), meniscus, and cartilage, present complex challenges in sports medicine and orthopedics due to the intricate cellular and molecular mechanisms involved in tissue damage and repair. Understanding the molecular biology underpinning these processes is crucial for developing effective therapeutic and rehabilitation strategies. This systematic review investigates the impact of mechanical loading on the cellular responses during knee joint injury repair, with a particular focus on the molecular pathways involved in tissue regeneration. Mechanical loading plays a dual role, where controlled early loading can promote tissue repair, while excessive or inappropriate loading can exacerbate tissue damage. Fibroblasts, chondrocytes, and mesenchymal stem cells (MSCs) are central to the repair process, and their activation, proliferation, and differentiation are regulated by key molecular pathways. Upon injury, mechanotransduction pathways such as the integrin/FAK signaling axis are activated, which convert mechanical signals into biochemical responses that regulate cell adhesion, migration, and extracellular matrix (ECM) synthesis. Additionally, mechanosensitive ion channels like Piezo1 and TRPV4 modulate intracellular calcium levels, triggering downstream signaling cascades such as calmodulin/CaMKII, which regulate gene transcription and cellular responses to mechanical stress. The YAP/TAZ pathway, a critical component of the Hippo signaling pathway, responds to mechanical stimuli and regulates cell proliferation and ECM production in fibroblasts and chondrocytes. YAP/TAZ translocate to the nucleus in response to mechanical loading, where they interact with transcription factors such as TEAD, promoting the expression of genes involved in collagen synthesis and tissue repair. In parallel, growth factors like transforming growth factor-beta (TGF-β) and fibroblast growth factor (FGF) activate the TGF-β/Smad and PI3K/Akt signaling pathways, driving MSC differentiation into fibroblasts and chondrocytes, essential for ligament and cartilage repair. Mechanical loading also influences the inflammatory response at the injury site by modulating immune cell activity. Early mechanical loading can shift macrophages from a pro-inflammatory M1 phenotype to an anti-inflammatory M2 phenotype, mediated by growth factors such as TGF-β and interleukin-10 (IL-10). This phenotypic switch promotes tissue regeneration by enhancing ECM synthesis and resolving inflammation, which is crucial for long-term joint health. Matrix metalloproteinases (MMPs), regulated by NF-κB and MAPK pathways, play a role in ECM remodeling, where an imbalance between MMPs and their inhibitors (TIMPs) can lead to excessive matrix degradation, impeding tissue repair. Furthermore, Wnt/β-catenin signaling is activated in response to moderate mechanical loading, promoting chondrocyte proliferation and enhancing cartilage repair by upregulating type II collagen and aggrecan synthesis. However, dysregulation of Wnt signaling under excessive mechanical stress can lead to chondrocyte hypertrophy and cartilage degradation, contributing to osteoarthritis development. This review also explores emerging therapeutic strategies that leverage the molecular biology of knee joint repair, including biologics like platelet-rich plasma (PRP) and MSC-derived exosomes, which deliver bioactive molecules that activate critical regenerative pathways such as TGF-β/Smad and PI3K/Akt. Gene therapies targeting Wnt signaling or YAP/TAZ offer potential for enhancing tissue regeneration by modulating mechanotransduction and repair processes at the molecular level. In conclusion, the molecular biology of cellular responses to mechanical loading is central to knee joint repair following injuries. By understanding these processes and targeting specific molecular pathways, clinicians can optimize rehabilitation protocols and develop novel therapeutic approaches that enhance tissue regeneration, prevent chronic degeneration, and restore joint function. This comprehensive synthesis highlights the importance of integrating molecular insights into treatment strategies for ACL, meniscal, and cartilage injuries to improve patient outcomes.

Yttria stabilized zirconia (Y-TZP) ceramics with drastically reduced yttria content have been introduced by different manufacturers aiming at improving the damage tolerance of ceramic components. In this study an alumina doped 1.5Y-TZP was axially pressed, pressureless sintered in air at 1250–1400 °C for 2 h and characterized with respect to mechanical properties, microstructure and phase composition. The material exhibits a combination of high strength of 1000 MPa and a high toughness of 8.5–10 MPa√m. The measured fracture toughness is, however, extremely depending on measurement protocol. Direct crack length measurements overestimate toughness due to trapping effects. The initially purely tetragonal material has a high transformability of > 80 %, the transformation behavior is predominantly dilatoric, measured R-curve related toughness increments are in good agreement with transformation toughness increments derived from XRD data.

Introduction: COVID-19's emergence caused devastating consequences worldwide, with high morbidity and mortality rates. Critically ill patients face challenges like acute respiratory failure requiring intensive measures, including mechanical ventilation. Mortality rates in ARDS are influenced by various factors. This paper focuses on describing characteristics, management, and survival factors of mechanically ventilated ICU patients in Saudi Arabia. Methods: a retrospective, noninterventional approach, we reviewed charts and data of all COVID-19-infected patients who were admitted to the ICU, particularly those requiring ventilation support at Aseer Central Hospital (ACH) in the southern region of Saudi Arabia. Results: The study enrolled 594 COVID patients, mean age 60.5 ± 17.3 years, with 67% males. Approximately half had O negative blood group. Common chronic health issues: diabetes mellitus (35.5%). Positive culture findings in almost 340 (57.2%), with Klebsiella pneumoniae being the most isolated microorganism (45.5%). Significant correlations found with mortality: age, blood culture, Rh positive group (P<0.05). Conclusion: this study provides critical insights into the clinical and epidemiological aspects of COVID-19 patients admitted to the ICU in a Saudi Arabian hospital. The research underscores the impact of age, comorbidities, laboratory markers, and treatment interventions on patient out-comes, emphasizing the significance of tailored management strategies in this context.

This work seeks to approach the comparative analysis of the distribution of POFs (polymeric optical fibers) arranged in a random and sorted manner in the manufacture of translucent concretes. The following characteristics were analyzed: compressive strength, flexural tensile strength, capillary water absorption and light transmittance. Portland cement, water, fine aggregate (sand), silica fume, polycarboxylate ether-based superplasticizer and polymeric optical fiber were used in the production of the composites. Except the fiber content, the mixture of all other inputs was kept as a fixed parameter. Groups with the following levels of POFs were produced: 0%, 2%, 3.5% and 5%. The POF content is the sum of the areas of the fiber sections in the composite with the total area of the translucent surface. The results showed that for the analysis of mechanical behavior (flexural tensile and compressive strength) and durability (capillary water absorption), composites with random and sorted fibers within the 2% POF presented to belong to statistically distinct groups. For the other fiber contents, there was no pattern of behavior, that is, it cannot be said that there is a difference within 3.5% or 5% POF between sorted and random fibers in relation to the mechanical and durability characteristics analyzed. As for the light transmittance, it was attributed that the statistical difference between the fiber arrangements only within the 5% POF content can be a consequence of their accumulation in certain points of the material, thus influencing this characteristic measured by a light meter.

The effect of graphene oxide (GO) on mechanical strengths and durability of cement composites has been studied by preparing GO-modified cement mortars. Thermogravimetric analysis (TGA) and nuclear magnetic resonance (29Si MAS-NMR) were performed on the cement paste to research the influence of GO on the hydration process and chain structure of calcium-silicate-hydrate (C-S-H) gels. In addition, mechanical strength test, such as compressive and flexural, were performed on cement mortars. The addition of GO at 0.05 wt.% (by weight of cement) increased the compressive strength by 9.02% after 28 days. Furthermore, the flexural strength of cement mortars with 0.05 wt.% GO and superplasticizer (SP) after 7 and 28 days increased by 12.26% and 21.86%, respectively, compared with reference mortar. At the same time, the effect of GO proved to be more significant and effective in the durability tests, suggesting that GO can enhance the microstructure through hydration products to create a highly cross-linked micro structure.

The main goal of this study was to introduce glycerol as a plasticizer to Polyvinyl Alcohol (PVA) membranes in order to increase their flexibility. The qualities of PVA membranes produced with various glycerol concentrations were evaluated. With the modified PVA membranes containing 5% glycerol, encouraging results were obtained. These membranes had superb optical characteristics and a 90% transmittance rate. This shows that the membranes are suited for applications needing excellent optical clarity since they permit light to travel through with little distortion. Importantly, FTIR analysis demonstrated that the addition of glycerol had no effect on the PVA membranes' chemical composition or structural integrity. In comparison to pure PVA Membrane, the modified membranes' water barrier qualities showed a considerable drop of up to 50%. The membranes are useful for applications requiring moisture management or breathability because of the decline, which points to an increase in permeability to water vapour. The large increase in flexibility, which was achieved by the PVA membranes containing 5% glycerol and beyond the brittleness typically associated with pure PVA, was a noteworthy discovery. The possible applications are expanded due to the increased flexibility, especially in industries where adaptability and flexibility are essential. Additionally, the addition of glycerol improved the thermal stability of the membranes, as they showed increased resistance to breakdown or decomposition at high temperatures. Additionally, the modified membranes' mechanical qualities were better than those of pure PVA, indicating that the glycerol addition improved their overall mechanical performance and tensile strength. PVA membranes were effectively made more flexible by adding 5% glycerol as a plasticizer. This led to membranes with superior optical qualities, reduced water barrier properties, greater flexibility, improved thermal stability, and maybe improved mechanical capabilities. These discoveries open up new opportunities for the use of these flexible PVA membranes in a range of settings, such as flexible packaging, biomedical materials, and other industries that need adaptive and flexible materials.

Deformation behavior of the composite "hen's eggshell - polymer plomb" under bending is examined. Polymer coating does not change the type of behavior of the composite based on eggshell that continues to be brittle despite the mechanical characteristics of the composite could vary in wide limits for brittle structure. Joining "hen's eggshell – polymer plomb" never crack under loading and, hence, it exhibits the high cohesion strength under stresses applied in these experiments. It seems that the composite "hen's eggshell - polymer plomb" could apply as the substitution of the composite "tooth enamel - polymer plomb" under elaboration of novel restorative materials for dentistry, namely, for estimation of their mechanical properties including cohesive strength.

Root crops grow in the soil deeply and bond with soil closely, which results in that the process of the separation between soil and root becomes the most difficult during the harvesting processes. In order to harvest root crops efficiently, the mechanical harvesting has become the main developing trend. However, high power and high damage rate are still occurred when mechanical harvester gets in touch with the roots. In this paper, we review the research of the development and evaluation of the mechanical harvesting of root crops and its performance optimization on the past years. The process of soil separation mainly consists in the initial separation between root and the ground and further separation between root and adhered soil. In general, the soil-cutting operation in the initial separation and the sieving mechanism in the further separation require high draught and power. And the dramatic friction, impact, pressure and so on, which happen in the components and soil-roots, are the key reasons to lead to root damage. The optimization of harvesting methods and parameters, including the digging shovel shape, working conditions, vibration, and screening way, is more significant in improving the harvesting performance. But there are still some limitations in the research and application of the mechanical harvester for root crops. Future research is suggested to focus on the development of the soil break-up when the digging shovel cutting soil, the insight into the interaction between soil and roots by different external compression loads, and the long-term studies to verify the high-efficiency and low-damage performances of mechanical harvester in practical application.

ZrO2-YO1.5-TaO2.5(ZYTO) composite ceramic is considered to be the candidate of next generation of thermal barrier coatings as its excellent thermal stability and low thermal conductivity in high temperature, however, the mechanical properties and fracture tougheness of ZYTO system may be the shortcomings compared with the 8YSZ. In this study, ZYTO composite ceramics were successfully prepared by chemical coprecipitation reaction, the microsture of resulting composites were studied as a function of doping of M-YTaO4. Mechanical properties, including the density, porosity, hardness and Young's modulus, are determinate; the toughening mechanism were verified by the crack growth behavior of Vickers indentation test Results suggested that M-YTaO4 refines the fluorite phase grain and strengthens the grain interface in the composite ceramic. The thermal mismatch between the second phase and matrix produces residual stress in the bulk and affects the crack propagation behavior. With the increase of M-YTaO4 doping, the grain coarsening and ferroelastic domains are observed in the experiments. The ferroelastic domains with orthogonal polarization directions near crack tip evidences the ferroelastic toughening mechanism. The competition among these crack behaviors, such as cracks deflection, bridging and bifurcation, dominates the actual fracture toughness of the composite. The best toughening formula is determinate in the two-phase region and the highest fracture toughness is about to 3.1MPa·m1/2. Above all, mechanical properties of ZYTO composite ceramics look potential for thermal barrier coatings materials.

It is important to add second- or third-phase materials to improve the physical, mechanical, and biodegradable properties of polypropylene (PP) nanocomposites. A unique hybrid bio-nanocomposite was fabricated using microparticle cellulose powder from wastepaper with a polypropylene (PP) polymeric matrix using a low-shear chaotic mixing method. A small amount (2-5%) of layered micro clay was also added to investigate the hybrid effect of nanocomposite fabrication on the mechanical properties. A low-shear chaotic melt mixing method induces the formation of nano cellulose structures and layered clay nanoparticles by via exfoliation. The nanoparticles were characterized using Fourier transform infrared (FTIR) spectroscopy. Mechanical properties such as the flexural strength (FS) and tensile strength (TS) were investigated using an Izod impact tester (IZ), and a dynamic mechanical testing analyzer (DMTA). Further, scanning electron microscopy (SEM) was used to observe the microstructure of the nanocomposite. In addition, differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) were conducted to investigate the crystallinity and degradation of the samples, respectively. The addition of wastepaper cellulose powder below 2.5 wt. % did not improve the mechanical properties, however, improvements were observed when more than 5wt.% wastepaper cellulose powder was added. With the addition of a small amount of nano-clay, the mechanical properties were significantly improved, and a synergistic effect could be noticed. The observed results were then compared with PP-clay nanocomposites used in automotive industries to replace cellulose nanocomposites. The application areas can also cover lead production in paper cups and vacuum foaming.

It is important to add second- or third-phase materials to improve the physical, mechanical, and biodegradable properties of polypropylene (PP) nanocomposites. A unique hybrid bio-nanocomposite was fabricated using microparticle cellulose powder from wastepaper with a polypropylene (PP) polymeric matrix using a low-shear chaotic mixing method. A small amount (2-5%) of layered micro clay was also added to investigate the hybrid effect of nanocomposite fabrication on the mechanical properties. A low-shear chaotic melt mixing method induces the formation of nano cellulose structures and layered clay nanoparticles by via exfoliation. The nanoparticles were characterized using Fourier transform infrared (FTIR) spectroscopy. Mechanical properties such as the flexural strength (FS) and tensile strength (TS) were investigated using an Izod impact tester (IZ), and a dynamic mechanical testing analyzer (DMTA). Further, scanning electron microscopy (SEM) was used to observe the microstructure of the nanocomposite. In addition, differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) were conducted to investigate the crystallinity and degradation of the samples, respectively. The addition of wastepaper cellulose powder below 2.5 wt. % did not improve the mechanical properties, however, improvements were observed when more than 5wt.% wastepaper cellulose powder was added. With the addition of a small amount of nano-clay, the mechanical properties were significantly improved, and a synergistic effect could be noticed. The observed results were then compared with PP-clay nanocomposites used in automotive industries to replace cellulose nanocomposites. The application areas can also cover lead production in paper cups and vacuum foaming.

The aim of this study was to compare the screw removal torque of mini conical prosthetic components and straight trunnion of indexed morse taper implants, after mechanical cycling. The sample consisted of 40 implants and 20 mini-conical prosthetic components (MC group) and 20 straight trunnion components (ST group). Each group consisted of 10 specimens, with 2 implants in each, and cobalt-chromium metallic crowns were screwed into each sample. The components of the MC group received a torque of 20 N.cm with a digital torque wrench and after 10 minutes were retightened with the same value as the initial torque. The components of the ST group received a torque of 30 N.cm, with a digital torque wrench and after 10 minutes, they were retightened with the same value. The screws of the respective crowns of the two groups received a torque of 10 N.cm and after 10 minutes were retightened with the same value. Each group was subjected to the fatigue test in a mechanical cycler at 2.000.000 cycles, with a load of 250 N and frequency of 4 Hz. At the end of the fatigue test, the loosening torque of each screw of the specimens was measured through a digital torque wrench. The data were analyzed by two-way ANOVA and Tukey test. In both groups, there were loss of torque. The results showed no statistic difference between MC and ST groups.

Nowadays, the massive use of tires generates large stocks of waste material which is a serious environmental problem. The usual method used for processing wasted tires is mechanical crushing, in which fiber, steel, and rubber are separated. The aim of this research is the recycling of the obtained rubber, called also GTR (Ground Waste Tires). With this purpose, the paper analyses the mechanical properties of the composites produced by mixing GTR with several industrial polymers. These composites are characterized by the percentage of GTR in the composite and its particle size. These two variables along with seven industrial polymers define a set of composites from which the mechanical properties are analyzed and presented. From the results, it can be drawn that this proposal could be a way to enhance some polymer properties and to contribute in some way to reduce the environmental wasted tires problem.

In-situ grown C_0.3N_0.7Ti and SiC, which derived from non-oxide additives Ti₃SiC₂, are proposed to densify silicon nitride (Si₃N₄) ceramics with enhanced mechanical performance. Remarkable increase of density from 79.20% to 95.48% could be achieved for Si₃N₄ ceramics with 5vol% Ti₃SiC₂. The capillarity of decomposed Si from Ti₃SiC₂, and in-situ reaction between nonstoichiometric TiC_x and Si₃N₄ were believed to be responsible for densification of Si₃N₄ ceramics. An obvious enhancement of flexural strength and fracture toughness for Ti₃SiC₂ doped Si₃N₄ ceramics was observed. The maximum flexural strength of 795 MPa for Si₃N₄ composites with 5vol% Ti₃SiC₂ and maximum fracture toughness of 6.97 MPa^.m^1/2 for Si₃N₄ composites with 20vol% Ti₃SiC₂ are achieved when mixed powders are hot-press sintered at 1700℃. Pull out of elongated Si₃N₄ grains, crack bridging, crack branching and crack deflection were demonstrated to dominate enhance fracture toughness of Si₃N₄ composites.

Abstract: Microstructural and mechanical properties of the eutectic Sn58Bi and micro-alloyed Sn57.6Bi0.4Ag solder alloys were compared. With the addition of Ag micro-alloy, the tensile strength was improved and this is attributed to a combination of microstructure refinement and an Ag3Sn precipitation hardening mechanism. However, ductility is slightly deteriorated due to the brittle nature of the Ag3Sn intermetallic compounds (IMCs). Additionally, a board level reliability study of Ag micro-alloyed Sn58Bi solder joints produced utilising a surface-mount technology (SMT) process, were assessed under accelerated temperature cycling (ATC) conditions. Results reveal that micro-alloyed Sn57.6Bi0.4Ag has a higher characteristic lifetime with a narrower failure distribution. This enhanced reliability corresponds with improved bulk mechanical properties. It is postulated that Ag3Sn IMCs are located at the Sn-Bi phase boundaries and suppress the solder microstructure from coarsening during the temperature cycling, hereby extending the time to failure.

Thought runs through the mind like blood runs through our body to keep us alive. Like the mind, the body does not stay inert and is in constant motion. Not a single cell in our body is left inert unless cell is under stress or dying. These scenarios are reflected upon when a person is sick, the person lies in bed with less movement; however, is active when the person is healthy. The topic of mechanical stimulation has emerged due to the increasing understanding of the physical stimulations we face each day. Further understanding of the mechanically-regulated mechanism can help us explore the pathological events in a disease. Here, we reviewed the role of sensory proteins in pathological events that are observed in cardiomyopathy, cancer, respiratory, renal, obesity, genetics, physical injury and bacterial infection. Taken together, sensory proteins are mechanically-activated which assist reception of external physical stimulation and convert into biochemical to trigger intracellular signaling cascade.

: The effect that the microstructure exerts on the TRIP phenomenon and on the mechanical properties in a multiphase steel was studied. Samples of an initially cold-rolled ferrite-pearlite steel underwent different intercritical annealing treatments at 750 °C until an equal fractions of austenite/ferrite was reached; the intercritical treatment was followed by isothermal bainitic treatments before cooling the samples to room temperature. Samples in the first treatment were heated directly to the intercritical temperature, whereas other samples were heated to either 900 or 1100 °C to obtain a fully homogenized, single phase austenitic microstructure prior to the conducting the intercritical treatment. The high temperature homogenization of austenite resulted in the decrease in its stability, so a considerable austenite fraction transformed into martensite by cooling to room temperature after the bainitic heat treatment. Most of the retained austenite transformed during the tensile tests, and as a consequence, the previously homogenized steels showed the highest UTS. In turn, the steel with a ferritic-pearlitic initial microstructure, exhibited higher ductility than the other steels and texture components that favor forming processes.

Regenerated silk (RS) is a protein-based “biopolymer” that enables the design of new materials; here, we called “bionic” the process of regenerated silk production by a fermentation-assisted method. Based on yeast’s fermentation, here we produced a living hybrid composite made of regenerated silk nanofibrils and a single-cell fungi, the Saccharomyces cerevisiae yeast extract, by fermentation of such microorganisms at room temperature in a dissolution bath of silkworm silk fibers. The fermentation-based processing enhances the beta-sheet content of the RS, corresponding to a reduction in water permeability and CO₂ diffusion through RS/yeast thin films enabling the fabrication of a mechanically robust film that enhances food storage durability. Finally, a transfer print method, which consists of transferring RS and RS/yeast film layers onto a self-adherent paraffin substrate, was used for the realization of heat-responsive wrinkles by exploiting the high thermal expansion of the paraffin substrate that regulates the applied strain, resulting in a switchable coating morphology from the wrinkle-free state to a wrinkled state if the food temperature overcomes a designed threshold. We envision that such efficient and smart coatings can be applied for the realization of smart packaging that, through such a temperature-sensing mechanism, can be used to control food storage conditions.

Biomaterials have assumed a decisive role in modern medicine by enabling significant advancements in medical care practices. These materials are designed to interact with biological systems, offering substantial solutions for various medical needs. In this research, bioceramic materials consisting of a bioactive hydroxyapatite-based matrix with Ti nanoparticles, were processed as promising materials. These bioceramics were obtained using mechanical milling, uniaxial pressing, and sintering as powder processing techniques. This study evaluates the effect of Ti additions on the structural, electrochemical, and mechanical properties of the hydroxyapatite ceramic material. Titanium additions were about 1, 2 and 3 wt%. The experimental results demonstrate that the biocomposite's structure has two hexagonal phases: one corresponding to the hydroxyapatite matrix and the other to the Ti as a reinforced phase. The biomaterials' microstructure is completely fine and homogeneous. The biomaterial reinforced with 1wt. % Ti exhibits the best mechanical behavior. In this context, Electrochemical tests reveal that bio-ceramics can achieve stability through an ion adsorption mechanism when exposed to a physiological electrolyte. Bioceramics, particularly those containing 1%Ti, develop their bioactivity through the formation a high-density hydroxide film during a porous sealing process at potentials around −782.71 mV, with an ionic charge transfer of 0.43x10^-9 A/cm². Finally, this biofilm behaves as a capacitor Cc = 0.18 nF/cm², resulting in lower ionic charge transfer resistance (Rct = 1.526x106 Ω-cm²) at the interface. This mechanism promotes the material’s biocompatibility for bone integration as an implant material.

ECM stiffness significantly influences ADSC differentiation, with YAP, a major transcription factor in the Hippo signaling pathway, playing a pivotal role. This study investigates how ECM stiffness affects ADSC differentiation and its relationship with YAP signaling. Different hydrogel concentrations were used to simulate varying ECM stiffness, and their effects on ADSC differentiation were analyzed through material properties, adipocyte-specific gene expression, lipid droplet staining, YAP localization, and protein levels. Results showed that increasing hydrogel stiffness enhanced adipocyte differentiation in a gradient manner. Inhibition of YAP signaling further increased lipid droplet accumulation, suggesting ECM stiffness affects adipogenesis by modulating YAP signaling and its cytoplasmic phosphorylation. This study reveals the molecular mechanism of ECM stiffness-dependent lipid deposition, highlighting YAP's regulatory role in adipogenesis. These findings provide insights into cell differentiation regulation and have implications for tissue engineering and obesity treatment strategies.

The knee joint, a crucial element in human locomotion, is subjected to various mechanical loads during daily activities and athletic pursuits. It functions as a complex, weight-bearing structure, facilitating movement and absorbing the stresses and strains imposed by physical activities. This review delves into the knee joint's response to mechanical loading, with a particular emphasis on mechanotransduction—the intricate process by which cells within the joint convert mechanical stimuli into biochemical signals. These signals initiate a cascade of cellular responses that are fundamental to maintaining joint health, promoting repair, and adapting to changes in the mechanical environment. Understanding the underlying mechanisms of mechanotransduction is essential for developing effective rehabilitation strategies aimed at treating knee joint injuries and managing degenerative conditions such as osteoarthritis. These strategies are crucial in clinical settings to enhance recovery, improve joint function, and mitigate pain and disability associated with knee joint disorders. This comprehensive review synthesizes current research on the cellular and molecular pathways involved in knee joint mechanotransduction. It evaluates the impact of different mechanical loading modalities—such as compression, tension, shear, and hydrostatic pressure—on the various tissues within the knee joint, including cartilage, synovium, ligaments, and tendons. By examining how these different loading conditions affect cellular behavior and tissue integrity, the review aims to provide a nuanced understanding of the biomechanical and biological responses of the knee joint to mechanical stress. Furthermore, the review discusses the implications of these findings for rehabilitation practices. It explores how knowledge of mechanotransduction can be applied to develop targeted therapeutic interventions, including controlled loading protocols, exercise regimens, manual therapy techniques, and the use of orthotic devices. By leveraging these insights, clinicians can optimize rehabilitation strategies to enhance tissue repair, restore function, and prevent further joint degeneration. Mechanotransduction in the knee joint involves several key cellular components, such as mechanoreceptors, ion channels, and signaling pathways that are activated by mechanical stimuli. These components play significant roles in regulating the functions of chondrocytes, synoviocytes, and fibroblasts—the primary cell types within the knee joint. For instance, chondrocytes, which are the main cellular component of cartilage, respond to mechanical loading by adjusting the synthesis and degradation of extracellular matrix components, thereby maintaining cartilage integrity and function. The synovial fluid, produced by synoviocytes, lubricates the joint and provides essential nutrients to the avascular cartilage. Mechanical loading affects synoviocytes, modulating the production of synovial fluid components such as hyaluronic acid and lubricin, which are critical for joint lubrication and protection against wear. Similarly, fibroblasts in ligaments and tendons respond to mechanical stress by altering collagen production and remodeling the extracellular matrix, which is vital for maintaining the strength and elasticity of these structures. This review also addresses the role of various signaling pathways, including the MAPK, NF-κB, and Wnt pathways, in mediating the cellular responses to mechanical stimuli. These pathways orchestrate the complex interactions between mechanical forces and cellular activities, influencing gene expression, protein synthesis, and cellular metabolism. By understanding these pathways, researchers and clinicians can identify potential targets for therapeutic interventions aimed at enhancing mechanotransduction and promoting tissue repair. In summary, this review highlights the importance of mechanotransduction in the knee joint's response to mechanical loading and underscores its relevance in designing effective rehabilitation approaches. Through a detailed analysis of current research, it aims to bridge the gap between basic mechanobiology and clinical practice, offering a comprehensive framework for understanding and improving knee joint health. By integrating insights from mechanobiology into rehabilitation strategies, clinicians can develop more effective treatments to support knee joint recovery, enhance functional outcomes, and prevent long-term degeneration.

In this study, Al-Al4C3 compounds were manufactured by mechanical milling followed by heat treatment. To analyze the microstructural evolution, the composites were sintered at 550°C during different sintering times of 2, 4 and 6 hours. The mechanical results suggest that dislocation density and crystallite size primary contribute to hardening before the sintering process, with a minimal contribution from particle dispersion in this condition. The compound exhibited a significant 75% increase in hardness after 2 hours of sintering, primarily attributed to the nucleation and growth of Al4C3 nanorods. The HRTEM analysis, combined with ge-ometric phase analysis (GPA) at and near the Al-Al4C3 interface of the nanorods, revealed strain field distributions primarily associated with partial screw dislocations and the presence of closely spaced dislocation dipoles. These findings are consistent with the microstructural parameters determined from X-ray diffraction pattern analysis using the convolutional multi-ple whole profile (CMWP) method. This analysis showed that the predominant dislocation character is primarily of the screw type, with the dislocation dipoles being closely correlated. Based on these results, it is suggested that samples with a lower weight percentage of rein-forcement and longer sintering times may experience reduced brittleness in Al/Al4C3 compo-sites. Strengthening contributions were calculated using the Langford–Cohen and Taylor equations.

The ECM is composed of a considerable number of biochemically and structurally diverse constituents. ECM is a highly dynamic system that constantly receives and sends biological, chemical and mechanical signals. Several studies suggest that mechanical signals derived from the extracellular microenvironment regulate skin regeneration and wound healing. We evaluated effects of a mixture of biomolecules extracted and purified from bovine colostrum on restoring the mechanical properties of ECM. Test measuring collagen contraction showed a significant difference in contraction activation in samples treated with the 2% colostrum derivative mixture compared to the control. The analysis of the supernatant showed an inhibition of metalloproteinase-2 expression and an increase in collagen secretion by fibroblasts in treatment samples. Our hypothesis is that the molecules extracted and purified from bovine colostrum restore the ECM environment qualitative and quantitative characteristics, thus guaranteeing through a mechanical action the restoration of the wound due to the transduction of the signal activated by the integrins.

This study investigates the utilization of innovative green composites made from hemp shiv, a waste by-product of hemp cultivation, with the aim of promoting sustainability within the construction industry. The manufacturing method involve the application of pressure in a mold to create the samples. These materials were produced using an environmentally friendly binder consisting of colophony, arabic gum and corn starch, moreover white glue and bioepoxy are also used to compare with the green resins. Three different binder compositions for the specimens. The samples underwent mechanical testing through tensile and bending assessments, and their performance was compared to that of non-green binders to validate the effectiveness of the manufacturing processes. The study revealed that decreasing the moisture content during the curing process is crucial for improving the mechanical properties. The best results were achieved when using arabic gum as a binder, yielding a tensile strength of 2.16 MPa and a bending strength of 5.25 MPa, with a composition of 62.5% hemp shiv and a manufacturing process involving a pressure of 5 MPa.

Mineral extraction is one of the most important for the economies of different countries, and Brazil is one of the world's primary iron ore producers. Unfortunately, the dams are still the main problem, mainly in Minas Gerais, especially after the Fundão Dam rupture happened in 2015. Additionally, there is still a massive presence of buildings produced on earth throughout the Minas Gerais mining region, built from the 18th century to today. Investigating the potential of IOT to be incorporated into traditional earthen construction techniques in regions affected by dam ruptures presents a relevant and innovative research approach. In addition, the local reuse of these sediments should be the priority. Thus, the main objective of this work was to collect, characterize, and analyze the possibilities of application of these tailings to produce RE. XRD, XRF, granulometry, porosity, specific density, toxicity, and MEV/EDS were performed on the samples collected at three points. To analyze the soil-IOT compatibility, representative mixtures of RE were produced, and the specific mass, compaction, and compressive strength were performed. It was observed that the IoT samples have a high silica content and that the mixtures of IOT-soil, even without cement, reached compressive strength values above the current international standards.

In recent decades, low-yielding seismic devices based on the use of friction dampers have emerged as an excellent solution for the development of building structures with improved reparability and resilience. Achieving an optimal design for such low-yielding seismic devices requires precise control of bolt preloading levels and predictability of the friction coefficient (CoF) between the damper interfaces. While various types of friction devices exist, capable of providing significant energy dissipation, ongoing research is focused on the development of novel friction materials that exhibit a stable hysteretic response, high CoF values, minimal differences between static and dynamic CoF, and predictable slip resistance. In this context, an experimental campaign was conducted at the STRENGTH Laboratory of the University of Salerno to evaluate the behaviour of new friction shims employing specially developed metal alloys. Specifically, the influence of the characteristics of the contact surfaces in the sliding area on the behaviour and performance of the friction device was analysed. The tests followed the loading protocol recommended by EN12159 for seismic device qualification. Monitored parameters included preloading force values and the evolution of slip resistance. The friction value was determined, along with its degradation over time. Finally, the material's performance in terms of hysteretic behaviour was assessed, providing a comparison of the tested specimens in terms of slip force degradation and energy dissipation capacity.

Mechanical ventilation systems used in houses are designed to reduce carbon dioxide emissions while minimizing the energy loss resulting from ventilation. However, increase in indoor fine particulate (PM2.5) concentration because of external PM2.5, influx through the ventilation system poses a problem. In this study, we analyzed the changes in indoor PM2.5 concentrations via dis-tinguishing between cases of high and low outdoor PM2.5 concentrations, considering the effi-ciency of filters used in residential mechanical ventilation systems. When using minimum effi-ciency reporting value (MERV) 10 filters in the ventilation system, the outdoor PM2.5 concentra-tion was 5 μg/m³; the indoor PM2.5 concentration became 73% after 60 min compared to the ini-tial. When the outdoor PM2.5 concentration was 30–40 μg/m³, the indoor PM2.5 concentration reached 91%. However, when MERV 13 filters were used, the indoor PM2.5 concentration con-sistently dropped to 73–76% regardless of the outdoor PM2.5 concentration. Furthermore, by comparing the established equation with the mass-balance model, the error was confirmed to be within 5%, indicating good fit. This allows the prediction of indoor PM2.5 under various condi-tions when using mechanical ventilation systems, enabling the formulation of strategies to maintain indoor PM2.5 as recommended by the World Health Organization.

Studies have shown the benefits of endovascular treatment (EVT) in adult stroke cases, but its application in pediatric stroke remains controversial. Despite evidence of improved outcomes in adults, there are no established recommendations for EVT in children. Conducting individual case reports and case series is vital to understanding its potential advantages and disadvantages in this context. This case report presents a 9-year-old boy who experienced basilar artery occlusion leading to a stroke and was effectively treated with mechanical thrombectomy.

Cancer cells exhibit aberrant extracellular matrix mechanosensing due to altered expression of mechanosensory cytoskeletal proteins. Aberrant mechanosensing of the tumor microenvironment (TME) by cancer cells has been shown to be associated with cancer development and progression. Recent studies show that altered mechanosensing changes the mechanobiological properties of cells, and, in turn, cells become susceptible to mechanical perturbations. Due to an increasing understanding of cell biomechanics and cellular machinery, several approaches have emerged to target the mechanobiological properties of cancer cells and cancer-associated cells to inhibit cancer growth and progression. In this review, we summarize the progress that happened in the development of mechano-based approaches to target cancer by interfering with the cellular mechanosensing machinery and overall TME.

The global production of macadamia nuts has witnessed a significant increase, resulting in the accumulation of large quantities of discarded nutshells. These nutshells possess remarkable hardness and toughness, comparable to aluminum. Incorporating natural fillers to enhance the properties of composite materials for various applications, including light duty, structural, and semi-structural purposes, is a common practice. Given their inherent hardness and toughness, macadamia nutshells present an intriguing choice as fillers, provided that the manufacturing conditions are economically viable. With the urgent need to shift towards natural fillers and reduce reliance on synthetics, exploring macadamia nutshells as components of natural fiber composites becomes imperative. This review aims to comprehensively examine the existing body of knowledge on macadamia nutshells and their bio-synthetic polymer composites, highlighting key research findings, achievements, and identifying knowledge gaps. Furthermore, the article will outline prospective areas of focus for future research endeavors in this domain, aligning with the universal goal of minimizing synthetic materials.

Although 7055 aluminum alloy is a deformed aluminum alloy and will show excellent mechanical properties after recrystallization after large deformation, it is a method to enrich its application range if rare earth is added and the rare earth phase dispersion is promoted by heat treatment. This article used optical microscopy, scanning electron microscopy energy dispersive spectroscopy (SEM-EDS), X-ray diffraction (XRD), micro Vickers hardness and room temperature stretching methods to study the as-cast 7055-xEr (x=0wt.%, 0.2wt.%, 0.4wt.%, 0.6wt.%, 0.8wt.%) aluminum alloy after being subjected to 460 oC×3h homogenization and 410 oC×1h solid solution+150 oC×12h aging treatment the changes in microstructure and properties. The results indicated that: when 0.2wt.%Er was added to 7055 aluminum alloy after solution at 410 oC×1h and aging at 150 oC×12h, the dendrite structure was significantly reduced, the grain thinning was obvious and the distribution was uniform, Al8Cu4Er phase appeared in the lamellar eutectic η-Mg(Zn,Al,Cu)2 structure at grain boundaries, and the hardness reached 168.8HV. The yield strength, tensile strength and elongation were 542.12Mpa, 577.67MPa and 8.36%, respectively.

This paper begins with an introduction to porcelain tiles. A review of the major scientific and technological features of the mullite−based porcelain tile (MPT) and anorthite−based porcelain tile (APT), focusing primarily on the raw material, processing, phase evolution and mechanical behavior, is then presented. Based on the porcelain tile firing behavior and a series of physical and chemical changes that can occur, a comprehensive comparison is described. In the last part, the prospects for further developments related to MPT and APT are discussed.

Polyethylene terephthalate (PET) is nowadays one of the most used polymers for packaging applications. Modifications induced by service conditions and the optimal mean to recycle this matter several times have to be perfectly understood to allow a reuse for similar application (from bottle to bottle for example). The present study aims to compare physico-chemical properties, crystalline organization, and mechanical behaviour of virgin (vPET) and recycled PET (rPET). Using different combined experimental methods (Calorimetry, Small Angle X-ray Scattering, Atomic Force Microscopy, DMA, and uni-axial tensile test), it has been proven that even if there is no change in the crystallinity of PET, the crystallisation process shows some differences (size and number of spherulites). The potential impact of these differences on local mechanical characterization, at the lamella scale, is explored and tends to demonstrate the development of homogeneous microstructure, leading to well-controlled and relevant local mechanical properties. This approach increases the understanding of crystallisation of PET and recycled PET during forming processes such as thermoforming or injection stretch blow moulding (ISBM) where elongation at break can depend on the microstructure conditioned by the crystallisation process.

Advanced Nano structural hard coatings are thin materials films that range in thickness from a few nanometers to a few micrometers and are applied to different surfaces to increase their hardness and wear resistance. Physical vapor deposition (PVD) or chemical vapor deposition (CVD) methods are frequently used to deposit these coatings. These coating’s distinctive characteristics result from their microstructure, which is made up of material columns or grains with a diameter of only a few nanometers. Increased hardness, higher wear resistance, and improved tribological properties result from these short dimensions. In applications with significant wear and/or high contact pressures, such as cutting tools, bearings, and engine parts, the usage of sophisticated Nano structural hard coatings is crucial. Advanced Nano structural hard coatings include, 1. Amorphous carbon coatings with high hardness, low friction, and exceptional wear resistance are known as diamond-like carbon (DLC) coatings. DLC coatings are frequently used in a variety of industries, including the automotive, aerospace, and biomedical ones. 2. Coatings made of titanium nitride (TiN): These metallic coatings have high hardness and wear resistance. Cutting tool, machining, and aerospace industries frequently use TiN coatings. 3. Chromium nitride (CrN) coatings: These coatings have great corrosion resistance, good wear resistance, and high hardness. Cutting tools, gears, and bearings are just a few of the objects that use CrN coatings. 4. Tungsten carbide (WC) coatings: These coatings, which have a high degree of hardness and wear resistance, are frequently employed in cutting tools and other applications that require wear resistance. Advanced Nano structural hard coatings provide many advantages over conventional coatings, including better hardness, increased wear resistance, and improved tribological qualities. The automotive, aerospace, and biomedical industries are just a few that could use these coatings. In this paper the author will explain about the design synthesis and applications of advanced Nano structural hard coating in aerospace and automotive applications.

Two-dimensional (2D) materials have been a research hot topic in the passed decades due to their unique and fascinating properties. Among them, mechanical properties plays an important role for their application. However, there lacks an effective tool for high-throughput calculating, analysing and visualizing the mechanical properties of 2D materials. In this work, we present, mech2d package, a highly automated toolkit for calculating and analysing second-order elastic constants (SOECs) tensor and relevant properties of 2D materials with considering their symmetry. In the mech2d, the SOECs can be fitted by both strain-energy and stress-strain approach, where the energy or strain can be calculated by first-principles engine, such as VASP. As a key feature, the mech2d package can automatically submit and collect the tasks from local or remote machine with robust fault-tolerant ability, make it suitable for high-throughput calculation. The present code has been validated by several common 2D materials, including graphene, black phosphorene, GeSe2 and so on.

Ventilation in prone position (PP) for 12 to 16 hours per day improves survival in ARDS. However, the optimal duration of the intervention is unknown. We performed a prospective observational study to compare the efficacy and safety of a prolonged PP protocol with conventional prone ventilation in COVID-19-associated ARDS. Prone position was undertaken if P/F <150 with FiO2>0.6 and PEEP>10cmH2O. Oxygenation parameters and respiratory mechanics were recorded before the first PP cycle, at the end of PP cycle and 4 hours after supination. We included 63 consecutive intubated patients with mean age 63.5 years. Of them, 37 (58.7%) underwent prolonged prone position (PPP group) and 26 (41.3%) standard prone position (SPP group). Median cycle duration for SPP group was 20 hrs and for PPP group 46 hrs (p<0.001). No significant differences in oxygenation, respiratory mechanics, number of PP cycles and rate of complications were observed between groups. The 28-day survival was 78.4% in the PPP group versus 65.4% in the SPP group (p=0.253). Extending the duration of PP was as safe and efficacious as conventional PP, but did not confer any survival benefit in a cohort of patients with severe ARDS due to COVID-19.

In this study, cement is used as the component that provides the stabilizing effect in order to evaluate the hardness and stability of loess soil. To assess the strength characteristics of loess soil reinforced with cement, samples were created with four different cement contents and three different curing times. The materials were put through a series of tests to determine their flexural strength, direct shear strength, indirect tensile strength, and unconfined compressive strength. An appropriate cement dosage was found, in addition to a durability index that could be used to quantify the effect of water absorption investigations on cement-stabilized loess. Both of these discoveries were made simultaneously. Analyses of investigations such as scanning electron microscopy (SEM) and energy dispersive X-ray fluorescence spectrometry (XRF) examinations were carried out so that the fundamental mechanics of the materials could be comprehended. According to the findings, the cohesion of cement-stabilized loess is significantly more sensitive to structure than the friction angle of the material, and the cohesion is responsible for the increase in shear strength after remolding. To get the desired level of strength, it is necessary to adjust the cement's proportions. In addition, as the curing period progresses, we see an increase in the cement-stabilized loess's resistance and stiffness. This is because of the interactions that take place between the structure and the mineral composition. It is believed that this event was caused by the cementation that occurs naturally. As a consequence of this reaction, the production of new cementitious materials takes place. The cation exchange that causes the hydration and pozzolanic reaction that leads to the creation of aggregates and interparticle flocculation is responsible for their production. These findings suggest that cement may be utilized as a simple and effective method of loess stabilization, which will ultimately result in improved performance of the loess.

In contrast to the traditional fillers, clay, in particular, natural smectite clay represents an environmentally significant alternative to improve the properties of polymers. Compared to con-ventional nanofillers, smectite clay can effectively enhance the physical and mechanical properties of polymer nanocomposites with a relatively small amount of addition (< 5 wt%). The present study focuses on investigating the reinforcing efficiency of different amounts (up to 5 wt%) of a natural Brazilian smectite clay on the mechanical and thermal properties of poly(butylene terephthalate) (PBT) nanocomposites. Natural Brazilian clay modified by addition of quaternary salt and sodium carbonate (MBClay) was infused into the PBT polymer by melt extrusion, using a twin-screw extruder. It was found that the best properties for PBT were obtained at 3.7 wt% of modified BClay. Tensile strength at break exhibited an increase of about 60 %, flexural strength increased by 24 % and flexural modulus increased by 17 %. In addition, an increase in the crystallinity percentage of PBT/BClay nanocomposite was confirmed by DSC and XRD analysis, and a gain of about 45 % in HDT was successfully achieved due to incorporation of 3.7 wt% of MBClay.

Hippotherapy is a popular rehabilitation method for children with cerebral palsy (CP), which is done by riding an actual horse or a horse riding simulator (HRS) device. Riding a real horse is more expensive than using an HRS device due to its high maintenance cost. However, most HRS devices commonly sold in the market are designed as exercise devices, not rehabilitation devices. Most of them are designed to simulate a horse's walk, trot, canter, or gallop gait at various speeds. Hippotherapy aims to improve the walking ability of CP patients. Therefore, the device should aim to replicate the walking gait of a healthy human, the end goal of hippotherapy. This problem motivates us to design and build a specialized HRS device replicating the walking gait of a healthy human that is suitable for hippotherapy, which is achievable by simulating a horse walking gait with several adjustments. We first studied and observed the walking gait cycle of a horse, then analyzed and derived a formulation of it. We then continue by designing an HRS device using a single electrical rotational motor and mechanical means to replicate the walking gait of a horse, then tune it to an extent to replicate a human walking gait. To measure the performance of our design, we compare the gait of the user when riding our device versus walking.

Alternating TiB2-dcMS and Cr-HiPIMS layers are used to fabricate TiB2/Cr multilayer films. In-troducing a 5-nm-thick Cr interlayer deposited under a substrate bias of -60 V produces slight increases of both film hardness and elastic modulus. The TEM observation indicates that the Cr grains favor epitaxially growth on TiB2 interlayer, forming a coherent TiB2/Cr interface. This produces the hardness increasement. Mechanic measurement by using AFM illustrates that the coherent interface increases the elastic modulus of the Cr up to ~280 GPa, which is significantly higher than bulk material.

Although the dry ice method used to synthesize exfoliated graphite/graphene is little known and used, it has significant advantages over others: it is low cost, simple, and a large quantity of material can be obtained using some inorganic and highly available acids (which can be reused). Despite the above advantages, the main reason for its incipient development is the resulting presence of magnesium oxide in the final product. In the present work, three different treat-ments were tested to remove this remnant using some acid chemical leaching processes, making use of hydrochloric acid, aqua regia, and piranha solution. Based on the experimental evidence, it was found that using aqua regia and combining the leaching process with mechanical milling was the most efficient way of removing such a remnant, the residue being only 0.9 wt.%. This value is low when compared to that obtained with the other acid leaching solutions and purifi-cation process (2.8 - 29.6 wt.%). A mandatory high-energy mechanical milling stage was neces-sary during this treatment, in order to expose and dissolve the highly insoluble oxide without secondary chemical reactions on the graphenes. High-energy mechanical milling is an effective route to exfoliate graphite/graphene, which allows the magnesium oxide to be more susceptible to acid treatment. The obtained surface area was 504 m2g-1; this high value resulting from the in-tense exfoliation can potentiate the use of this material for a wide variety of applications.

With the increase in occupation-specific risks of lip cancer associated with solar radiation, there is a need for developing photoprotective lipsticks to protect skin against harmful effects of UV radiation. Considering the unique chemical and physical properties of low-molecular-weight organogelators (LMOGs), the present study intended to assess the UV protective properties of LMOGs-based lipstick formulations. In this study, dibenzylidene-D-sorbitol (DBS) and 12-hydroxystearic acid (12-HSA) were used to formulate lipsticks : L1 (1% DBS), L2 (10% 12-HSA), L3 (1.5% DBS) and L4 (control, no LMOGs). The lipstick formulations were tested for in vitro sun protection factors (SPF), UVA protection factor (UVA-PF), thermal, mechanical and texture analyses. Lipsticks with LMOGs exhibited higher UVA-PF and SPF, and more particularly 12-HSA-based lipstick. Results showed also the viscoelastic and heat-resistant properties of LMOGs and their effect of increasing pay-off values. In general, texture analysis indicating that 12-HSA-based lipstick was significantly harder to bend compared to control, while other formulations became softer and easier to bend throughout the stability study. Finally, sensorial and instrumental analyses permitted to classify lipsticks into two groups. This work suggests the potential use of LMOGs as a structuring agent for lipsticks paving the way towards more photoprotective and sustainable-derived alternatives.

The article discusses the results of investigations performed during a thermo-mechanical treatment of forgings made of chromium-molybdenum 42CrMo4 grade steel. The treatment was realized during a regular series production. The forging process was combined with a heat treatment carried out directly after forging on a specially adapted station. Such a production technology will make it possible to eliminate the step of repeated heating of the forgings. On the example of an element of a steering gear, it was demonstrated how it is possible to perform an isothermal annealing process starting from the temperature at which the trimming of the forgings ends. During the cooling of the forgings, it is enough to maintain the temperature at the proper level in order for the exothermal phase transformation of austenite into pearlite to take place. With an appropriate design of the processing line, the heat released during the transformation could be used to maintain the applied temperature, thus limiting the consumption of energy needed to power the devices. The test results show that, with the properly selected temperature of isothermal annealing, it is possible to obtain an equilibrial ferritic-pearlitic structure in the required hardness scope. Introducing such a solution into the industrial practice would allow significant savings of the energy used for the heat treatment.

The present study investigated the effects of alloying and nano-reinforcement on the mechanical properties (microhardness, tensile strength, and compressive strength) of Mg-based alloys and composites. Pure Mg, Mg-3Sn alloy, and Mg-3Sn+0.2GNP alloy-nanocomposite were synthesized by powder metallurgy followed by hot extrusion. The microstructural characteristics of the bulk extruded samples were explored using X-ray diffraction, field-emission scanning electron microscopy, and optical microscopy and their mechanical properties were compared. The microhardness, tensile strength, and compressive strength of the Mg-3Sn alloy improved when compared to those of monolithic Mg sample and further improvements were displayed by Mg-3Sn+0.2GNP alloy-nanocomposite. No significant change in the compressive strain to failure was observed in both the alloy and the alloy-nanocomposite with respect to that of the pure Mg sample. However, an enhanced tensile strain to failure was displayed by both the alloy and the alloy-nanocomposite.

The paper presents an analysis of the possibility of producing traction brushes from waste materials. Brushes are used to ensure good electrical contact between the rail and the pantograph. Slides are produced in the process of hot pressing, with parameters of heating up to max 175 ⁰C, at the minimal pressure value of 200 MPa. The developed brushes with a high (55-60%) content of recycled materials have comparable characteristics to commercial brushes, and some of the prototypes are even more durable and break-resistant.

The SARS-Cov-2 virus, which causes COVID 19, uses the cell surface protein ACE2 as receptor for entry into cells. Critically ill COVID-19 patients often require prolonged mechanical ventilation which can cause mechanical stress to lung tissue. In vitro studies have shown that expression of ACE2 in alveolar cells is increased following mechanical stretch and inflammation. Therefore, we analyzed transcriptome datasets of 480 (non-COVID-19) lung tissues in the GTex tissue gene expression database. We found that mechanical ventilation of the tissue donors increased the expression of ACE2 by more than two-fold (p<10^-6). Analyses of transcriptomes of mechanically ventilated mice in the GEO database indicate that this alveolar cell response to stretch and inflammation is mediated by the chemokine midkine. Using a novel big knowledge network approach (SPOKE) we also found in transcriptomes of pharmacological perturbations (LINCS) that corticosteroids down-regulate midkine in pulmonal cells, and confirmed this in GEO transcriptomes of animal studies. Thus, mechanical ventilation of patients with COVID-19 pneumonia may eo ipso facilitate viral propagation in the lung, further accelerating the pulmonal pathology that has necessitated mechanical ventilation in the first place. This vicious cycle presents a rationale for the temporary treatment with corticosteroids to modulate the midkine-ACE2 axis in ventilated COVID19 patients and for gentler ventilation protocols.

In this research, the feasibility of using bottom ashes generated by the combustion of biomass (olive pruning and pine pruning) as a source of aluminosilicates (OPBA) has been studied, replacing the metakaolin precursor (MK) in different proportions (0, 25, 50, 75 and 100 wt. % substitution) for the synthesis of geopolymers. As alkaline activator an 8 M NaOH solution and a Na2SiO3 have been used. The geopolymers were cured 24 hours in a climatic chamber at 60 ° C in a water-saturated atmosphere, subsequently demoulded and cured at room temperature for 28 days. The results indicated that the incorporation of OPBA waste, which have 19.7 wt. % of Ca, modifies the characteristics of the products formed after alkaline activation. In general terms, the incorporation of increasing amounts of calcium-rich ashes results in geopolymers with higher bulk density. The compressive strength increases with the addition of up to 50 wt. % of OPBA with respect to the control geopolymers, contributing the composition of the residue to the acquisition of a better behaviour mechanical. The results indicate the potential use of these OPBA waste as raw material to produce unconventional cements with 28-day curing strengths greater than 10 MPa, and thermal conductivities less than 0.35 W/mK.

The objective of this study is to conduct a mineralogical and chemical characterization of the mortars Roman archaeological site of Volubilis to rebuild spare mortars for restoration. We take samples of mortar, broken tile palate garden, and pavement mosaic Falavius Germanus houses. The analysis by X-ray diffraction reveals the coarse mortar Flavius Germanus is made of quartz and calcite with feldspar and probably, mica and dolomite in small amounts. The binder end is formed calcite and quartz. However, the broken tile mortar is formed by coarse particles, clay base mixed with a binder phase dominated by calcite. These results allowed us to reformulate spare mortars for the restoration of damaged Roman mosaics. The mortars are made up by 63.6% of lime and 36.4% of sand(with 4.19% of large grain, 71, 04% of coarse sand, 24.22%, of fine sand and 0.55% fines parts).The performance of these mortars was tested by mechanical testing.

In this work we produced biochar by coffee waste and use it as filler in epoxy resin composite with the aim to increase their electrical properties. The biochar and biochar based composite electrical conductivity were studied in function of applied pressure and compared with carbon black and carbon black composite. The applied pressure has the aim to investigate the behaviour of filler in powder or dispersed in composite in function of compression. Results showed that even if the coffee biochar has less conductivity if compared with carbon black in powder form, it has better conductivity in composite if compared with carbon black. Composite mechanical properties were tested and they are generally improved respect to neat epoxy resin.

Alumina dispersion-strengthened copper, Glidcop, is used widely in high-heat-load ultra-high-vacuum components for synchrotron light sources (absorbers), accelerator components (beam intercepting devices) and in nuclear power plants. Glidcop has similar thermal and electrical properties to OFE (oxygen free electrical) copper, but has superior mechanical properties, thus making it a feasible structural material; its yield and ultimate strength are equivalent to those of mild-carbon steel. The purpose of this work has been to develop a brazing technique to join Glidcop to Mo, using a commercial Cu-based alloy. The effects of the excessive diffusion of the braze along the grain boundaries on the interfacial chemistry and joint microstructure, as well as on the mechanical performance of the brazed joints, has been investigated. In order to prevent the diffusion of the braze into the Glidcop alloy, a copper barrier layer has been deposited on Glidcop by means of RF-sputtering.

In this study, a 5vol. % (TiBw+TiCp)/Ti composite pancake with a diameter of 260mm was prepared by casting followed by open die forging in (α+β) phase region. The microstructures of the composite pancake are inhomogeneous, in terms of both matrix microstructure and distribution of reinforcements. The matrix microstructures were gradually refined from the periphery to centre of the pancake. The TiBw and TiCp reinforcements tend to be uniformly distributed in the centre region and. It is suggested that the microstructure difference can be mainly ascribed to the temperature variation from the periphery to the centre. Additionally, tensile testing results showed that the centre region of the composite pancake exhibits higher strength than the peripheral region. The strengthening mechanism and the softening behavior of the composite pancake with temperature is discussed.

In this short communication, we conducted first-principles calculations to explore the stability of boron monochalcogenides (BX, X=S, Se or Te), as a new class of two-dimensional (2D) materials. We predicted BX monolayers with two different atomic stacking sequences of ABBA and ABBC, referred in this work to 2H and 1T, respectively. Analysis of phonon dispersions confirm the dynamical stability of BX nanosheets with the both 2H and 1T atomic lattices. Ab-initio molecular dynamics simulations reveal the outstanding thermal stability of all predicted monolayers at high temperatures over 1500 K. BX structures were found to exhibit high elastic modulus and tensile strengths. It was found that BS and BTe nanosheets can show high stretchability, comparable to that of the graphene. It was found that all predicted monolayers exhibit semiconducting electronic character, in which 2H structures present lower band-gaps as compared with 1T lattices. The band-gap values were found to decrease from BS to BTe. According to the HSE06 results, 1T-BS and 2H-BTe show respectively, the maximum (4.0 eV) and minimum (2.06 eV) electronic band-gaps. This investigation introduces boron monochalcogenides as a novel class of 2D semiconductors with remarkable thermal, dynamical and mechanical stability.

The management of existing water distribution system (WDS) is challenged by ageing of infrastructure, population growth, increasing of urbanization, climate change impacts and environmental pollution. Therefore, there is a need for integrated solutions that support decision makers to plan today, while taking into account the effect of these factors in the mid and long term. The paper is part of a more comprehensive project, where advanced hydraulic analysis for WDS is coupled with a dynamic resources input-output analysis model. The proposed modeling solution can be used to optimize the performance of a water supply system while considering also the energy consumption and consequently the environmental impacts. Therefore, as a support tool in the management of a water supply system also in the intervention planning. Here a possible application is presented for rehabilitation/replacement planning while maximizing the network mechanical reliability and minimizing risk of unsupplied demand and pressure deficit, under given economic constraints.

High level of noise is a disturbance to the human environment. Noise in industries is also an occupational hazard because of its attendant effects on workers’ health. Noise presents health and social problems in industrial operations, and the source is related to the machineries used in the industries. One of the unique features of the noise associated with wood machinery is the level of exposure and duration. Equipment used in a factory can be extremely loud. They can produce noise at decibels high enough to cause environmental health and safety concerns. The mechanically driven transport and handling equipment, cutting, milling, shaping and dust extractor installations in the wood industry generate noise. The sources of noise pollution have increased due to non-compliance with basic safety practices. The increased use of locally fabricated machine in the industry has increased the level of noise and vibration. The effects of industrial noise pollution as discussed include: increase in blood pressure; increased stress; fatigue; vertigo; headaches; sleep disturbance; annoyance; speech problems; dysgraphia, which means reading/learning impairment; aggression; anxiety and withdrawal. As presented in this paper, noise control techniques include; sound insulation, sound absorption, vibration damping and Vibration isolation.

TiNbZrTa alloys are promising for multidisciplinary applications, such as refractory and biomedical purposes due to their high thermal stability and non-toxicity. Hardness and elastic modulus are among the key features for their adequate industrial applications. The influence of porosity and Ti/Ta ratio were investigated on TiNbZrTa alloys produced by three different processing routes, i.e., (i) blend element and posterior press and sintering (BE + P&amp;S), (ii) mechanical alloying with press and sintering (MA + P&amp;S), and (iii) arc melting and casting. Atomic diffusion was improved during processing, resulting in lower porosity in the following order: casting &lt; MA + P&amp;S &lt; BE + P&amp;S. Ta offered limited atomic diffusion due to its high melting point compared to other constituent elements. Thus, the total porosity of alloys increased with increasing the Ta contents, i.e., by lowering the Ti/Ta ratio. However, the Ti/Ta ratio did not considerably affect the bonding energy or the elastic modulus. Hardness was increased significantly in dense alloys compared to the porous ones. However, porosity and Ti/Ta ratio did not show a clear trend in hardness among the porous alloys.

This study investigates the influence of four soil improvement methods—microbially induced carbonate precipitation (MICP), electrokinetics (EK), chemical additives, and a combination of EK and chemical additives—on the dispersivity, mechanical properties, and microstructure of dispersive soil. A series of tests was designed to evaluate the effectiveness of these methods on dispersive soil. Both the original and treated soil samples were tested to assess changes in soil properties, including dispersivity, plasticity, pH, unconfined compressive strength (UCS), shear strength, and microstructure. Dispersivity was assessed using pinhole tests, crumb tests, double hydrometer tests, and exchangeable sodium percentage tests. The experimental results indicate that the combined EK and chemical additives method significantly reduces the dispersivity and plasticity of the dispersive soil compared to the other methods, leading to improved UCS. The EK and chemical additive methods individually demonstrate effective modification under a voltage of 48V and an additive content of 4%, respectively, enhancing the shear strength of the dispersive soil. MICP does not significantly improve the dispersivity of dispersive soil, it does enhance the shear strength of the treated soil, with a particularly notable increase in the internal friction angle. Overall, the combined method shows more remarkable improvements in the dispersive soil than any single method. In summary, the combination of EK and chemical additives has significant potential for improving the dispersivity and mechanical properties of dispersive soil.

Lightweight concrete is a promising alternative in modern construction due to its reduced weight and potential to improve thermal and structural efficiency. Incorporating sustainable materials, such as nopal mucilage and aloe vera, can optimize its properties, promoting more eco-friendly practices in the industry. This study evaluates six concrete mixtures using different dosages of tuff, expanded clay, nopal mucilage, and aloe vera. Physical and mechanical tests were conducted, and the results revealed varied behaviors: mixtures with aloe vera showed extremes in water absorption and consistency, with tuff being very fluid and expanded clay having good workability. Mixtures with nopal mucilage were drier and less workable. In contrast, mixtures with expanded clay showed higher bulk density and variations in consistency and water absorption. Compressive strength varied depending on the lightweight agents used: mixtures with nopal mucilage-expanded clay and aloe vera-expanded clay showed moderate strengths, suggesting that these combinations can improve the strength of lightweight concrete. The different lightweight agents also affected the thermal and physical properties and the fractal dimension of the mixtures, indicating a greater structural complexity and better heat retention in combinations of expanded clay with nopal mucilage or aloe vera.

High-entropy alloys have attracted widespread attention from researchers worldwide due to their unique microstructure and outstanding mechanical properties, making them a prominent focus in the field of metallurgy. Among the various high-entropy alloys, the CoCrCuNi system was among the first alloys discovered, and it has shown significant progress in development. By employing different preparation and heat treatment processes, researchers have obtained alloys with diverse performances. The addition of various alloying elements or other components can lead to pronounced variations in the properties of CoCrCuNi high-entropy alloys. This work provides a comprehensive review of recent research progress on CoCrCuNi high-entropy alloys both domestically and internationally. It covers the preparation methods, thermodynamic and kinetic simulation calculations, as well as discussions on heat treatment processes and the influence of alloying elements on the microstructure and mechanical properties of CoCrCuNi high-entropy alloys. Finally, the review concludes with a prospective analysis and predictions for the potential applications and future directions in developing novel high-entropy alloys.

Background/Objectives: Current guidelines recommend intravenous thrombolysis (IVT) followed by mechanical thrombectomy (MT) for patients with acute ischemic stroke (AIS) caused by large vessel occlusion (LVO). This combined approach, known as bridging therapy (BT), is believed to increase the likelihood of a favorable functional outcome when administered within 4.5 hours of symptom onset. However, the benefits of BT over direct mechanical thrombectomy (d-MT) remain debated. This study aimed to compare the outcomes of AIS-LVO patients undergoing MT within 6 hours of symptom onset, with and without prior IVT. Methods: Within the prospective TINL STROKE-registry, AIS-LVO patients admitted to the Department of Neurology, University of Pécs, between February 2023 and June 2024 were investigated. The primary endpoint was the proportion of patients reaching functional independence at 90 days, defined as a modified Rankin Scale (mRS) score of 0-2. Secondary endpoints included clinical improvement at 72 hours (National Institute of Health Stroke Scale [NIHSS] score of ≤1 or a change from baseline [ΔNIHSS] of ≥4) and successful recanalization (modified Thrombolysis in Cerebral Infarction [mTICI] score ≥2). Safety outcomes were evaluated based on thrombus migration and intracranial hemorrhage (ICH). Results were compared using linear and logistic regression analyses adjusted for baseline variables. Results: Of 82 patients, 51 (62.2%) received BT, while 31 (37.8%) underwent d-MT. The BT group showed a significantly higher rate of functional independence (45.7% vs. 17.2%, p=0.014) and a lower 90-day mortality rate (13.7% vs. 35.5%, p=0.029). Multivariate analysis revealed that IVT was independently associated with favorable functional outcome (p=0.011) and reduced mortality (p=0.021). No significant differences were observed in terms of clinical improvement at 72 hours, successful recanalization, thrombus migration, or hemorrhagic transformation between the groups. Conclusions: This study supports current guidelines recommending BT for thrombectomy-eligible AIS-LVO patients, offering new insights into the ongoing clinical debate.

Strong yet ductile alloys have long been desired for industrial applications to enhance structural reliability. This work produced two (CoCrNi)93.5Al3Ti3C0.5 medium-entropy alloys with exceptional strength-ductility combinations, via short/medium (3 min/30 min)-time annealing after hot-rolling. Three types of intergranular precipitates including MC, M23C6 carbides, and L12 phase were detected in both the samples. Noticeably, the high density of intragranular L12 precipitates were only founded in the medium-time annealed sample but not in another one. Upon inspection of deformed substructure, it was revealed that the plane slip is the dominant deformation mechanism of both the alloys. This is related to the lower stacking fault energy, higher lattice friction induced by C solute, and slip plane softening caused by intragranular dense L12 precipitates. Additionally, we noted that the stacking fault and twinning act as the mediated mechanisms in deformation of the short-time annealed alloy, while only the former in the medium-time annealed one. It is attributed to the higher energy stacking faults and the increased critical twinning stress caused by intragranular dense L12 precipitates that inhibited the twinning tendency. Our present findings provide not only a guidance for optimizing the mechanical properties of high/medium-entropy alloys, but also a fundamental understanding of deformation mechanisms.

One of the primary causes of the mechanical seal failure is rotor vibration. Traditional dynamic seal models often would not be able to fully explaining the failure mechanisms. The seal dynamic models proposed in this paper, including those developed by the authors, prove valuable in predicting seal dynamics during operation in specific turbomachinery and in explaining the causes of seal failure. The single-mass dynamic model is suitable for analyzing contact mechanical seal and simple design dry gas seals dynamics. The two-mass dynamic model is used for investigating operational dynamics processes in classical dry gas seals under complex loading conditions. The three-mass dynamic model is used to study various complex mechanical seal types. This model is able to determine the normal operating condition range and to explain leakage mechanisms in the presence of excessive rotor vibrations.

In these last years, self-healing polymers have emerged as a topic of considerable interest owing to their capability to partially restore material properties and thereby extend the product's lifespan. The main purpose of this study is to investigate the nano-indentation response in terms of hardness, reduced modulus, contact depth and coefficient of friction of a self-healing resin developed for use in aeronautical and aerospace contexts. To achieve this, the bifunctional epoxy precursor underwent tailored functionalization to improve its toughness, facilitating effective compatibilization with a rubber phase dispersed within the host epoxy resin. This approach aimed to highlight the significant impact of the quantity and distribution of rubber domains within the resin on enhancing its mechanical properties. The main results are that pure resin exhibits a higher hardness (about 36.7% more) and reduced modulus (about 7% more), consequently leading to a lower contact depth and coefficient of friction (11.4% less) compared to other formulations that, conversely, are well-suited for preserving damage from mechanical stresses due to their capabilities in absorbing mechanical energy. Furthermore, finite element method (FEM) simulations of the nanoindentation process were conducted. The numerical results were meticulously compared with experimental data, demonstrating a good agreement. This validation of the FEM model underscores its efficacy in predicting the mechanical behavior of nanocomposite materials under nanoindentation. The proposed investigation aims to contribute knowledge and optimization tips about self-healing resins.

Bi1-xSbx crystal is one of the best n-type thermoelectric materials below 200 K, but its weak mechanical strength hinders practical applications for deep refrigeration. Herein, we adopted the mechanical enhancement method of hot extrusion to investigate the comprehensive mechanical and thermoelectric properties of Bi0.905Sb0.095. It revealed that reducing the grain size of the matrix and increasing the extrusion ratio can improve the gain size uniformity and mechanical properties. While the thermoelectric performance depends on the texture, grain size, and local composition. The extruded sample prepared by ingot with the high extrusion ratio of 9:1 generated a high texture degree of (001) plane and small grain sizes between ~4-40 mm, which resulted in the high bending strength of Bi1-xSbx ~130 Mpa and a high-power factor of ~ 68 μW·cm-1·K-2@173 K, as well as the relative high figure of merit of 0.25@173K. This work highlights the importance of the uniform distribution of the grain size and the compositions for Bi1-xSbx, as well as the required universal key parameter for the hot-extrusion method.

Background/Objectives: The purpose of this study was to evaluate the relationship between 1-year mortality and health insurance benefit extension policy items in severe pneumonia pa-tients requiring mechanical ventilation using a South Korean nationwide cohort. Methods: A nationwide population-based retrospective study was conducted using the Korean National Health Insurance database. A total of 1,099 patients (542 patients in the health insurance benefit item group and 557 patients in the control group) were included. The primary outcome was 1-year mortality. Results: Among patients with health insurance benefit extension policy items, 203 patients (37.5%) were diagnosed with hemato-oncological disease, who were categorized as group A, and 339 patients (62.5%) were diagnosed with cerebrovascular, cardiovascular, or rare diseases, who were categorized as group B. Group B had lower 1-year mortality (50.7% vs. 62.5%, P

The development of offshore wind farms requires robust bonding solutions that can withstand harsh marine conditions for the easy integration of secondary structures. This paper investigates the durability performance of two adhesives: Sikadur 30 adhesive and Loctite UK 1351 B25 for use in offshore wind environments. Tensile tests on adhesive samples and accelerated aging tests were carried out under a variety of temperature and environmental conditions, including both dry and wet conditions. The long-term effects of aging on adhesive integrity are investigated by simulating the operational life of offshore installations. The evolution of mechanical properties, studied under accelerated aging conditions, provides an important indication of the longevity of structures under normal conditions. The results show significant differences in performance be-tween the two adhesives, highlighting their suitability for specific operating parameters. It should also be noted that for both adhesives, their exposure to different environments (seawater, distilled water, humid climate) over a prolonged period has shown that i) Loctite adhesive has a slightly faster initial uptake than Sikadur adhesive, but the later reaches an asymptotic plateau with a lower maximum absorption rate than Loctite adhesive; and ii) a progressive deterioration in the tensile properties following an exponential function. Therefore, aging behavior results showed a clear correlation with Arrhenius' law, providing a predictive tool for the aging process. Thus, the aging process of the two adhesives follows Arrhenius kinetics.

Conductive hydrogels combine the properties of both hydrogels and electrical conductivity, making them soft, flexible, and biocompatible. These properties enable them to conform to irregular surfaces, stretch and bend without losing their electrical conductivity, and interface with biological systems. Conductive hydrogels can be utilized as conductive traces, electrodes, or as a matrix for flexible electronics. Exciting applications in sensors, tissue engineering and human-machine interaction have been demonstrated worldwide. This review comprehensively covers the progress in this field, focusing on several main aspects: functional materials, performance improvement strategies, and wearable applications in human-related areas. Furthermore, the major approaches and challenges for improving their mechanical properties, conductivity, and long-term stability are systematically summarized.

The nickel-chromium-molybdenum alloy 625 exhibits an excellent combination of mechanical properties and corrosion resistance. However, the high temperature plastic deformation process and the heat treatment represent critical aspects and the adoption of non-optimal parameters can result in excessive grain coarsening and loss in mechanical strength. This detrimental behavior is worsened by the presence of a narrow region of temperatures and strain rates for complete recrystallization and the absence of phase transformation temperatures. In this alloy, the presence of sufficient amounts of niobium, titanium and aluminum permits slow age-hardening response upon single-aging treatments. Therefore, when the soft- or solution-annealed condition is associated with insufficient mechanical properties, this potentiality can be exploited to improve the mechanical strength and prevent waste of material and resources. Since the precipitation kinetic of the hardening γ^'' phase can be accelerated by prior nucleation treatment, different time-temperature combinations of double aging at 732 °C and 621 °C are investigated to reduce the overall heat treatment time. However, the simultaneous formation of Cr-rich carbides can dramatically affect the intergranular corrosion resistance. For this reason, a performance map is developed to compare all the tested conditions and identify the best compromise in terms of mechanical strength and corrosion rate.

Industry 4.0 is an industrial paradigm that is causing changes in form and substance in factories, companies and businesses around the world, and is impacting work and education in general. In fact, the disruptive technologies that frame the fourth industrial revolution have the potential to improve and optimize manufacturing processes and the entire value chain, which can lead to an exponential evolution in the production and distribution of goods and services. All these changes imply that the fields of engineering knowledge must be oriented towards the concept of Industry 4.0, for example Mechanical Engineering. The development of various physical assets that are used by cyber-physical systems and digital twins is based on Mechanics. However, the specialized literature on Industry 4.0 says little about the importance of Mechanics in the new industrial era and more importance is given to the evolution of Information and Communication Technologies and Artificial Intelligence. This article presents a frame of reference about the importance of Mechanical Engineering in Industry 4.0 and proposes an extension to the concept of Mechanics 4.0, recently defined as the relationship between Mechanics and Artificial Intelligence. For the analysis of Mechanical Engineering in Industry 4.0, the criteria of the four driving forces that defined Mechanics in the third industrial revolution was used. An analysis of Mechanical Engineering Education in Industry 4.0 is presented, and the concept of Mechanical Engineering 4.0 Education is improved. Finally, the importance of making changes in the educational models of engineering education is described.

With the advancement of Additive Manufacturing and its applications in various industrial segments, it becomes increasingly important to investigate the processability parameters associated with nano-reinforcement. This study examines the influence of infill parameters, such as patterns (hexagonal, triangular and concentric), shape (solid and honeycomb) and concentrations by mass of Carbon Nanotubes (CNTs) at 1.0 wt% and 2.0 wt% on the mechanical compression properties of the 3D printed material. In this sense, nanocomposites based on Polylactic Acid (PLA) matrix nano-reinforced by CNTs were characterized using the Scanning Electron Microscopy -SEM, X-ray Diffraction, Raman Spectroscopy techniques and mechanical analysis. The mechanical properties of both the matrix and the nanocomposites were determined through mechanical compression tests, in accordance with [1]. SEM revealed compacted regions, voids, and detachment in the structures. XRD characterization indicated PLA predominantly amorphous nature, while CNTs exhibited characteristic diffractions of carbon nanotubes. Raman characterization showcased bands and characteristic vibrations of CNTs and PLA, nanocomposites' vibrational modes combine those of CNTs and PLA. Mechanical compression analysis indicates a direct influence of infill pattern, shape, and nano-reinforcement. The triangle pattern outperformed other patterns, exhibiting a 15.03% increase compared to concentric and 8.8% compared to hexagon infill. In nanocomposites, all showed higher compressive strength than the matrix. For PLA/1.0%CNTs, strength was 16.8%, and for PLA/2.0%CNTs, it reached 39.2%. In honeycomb shapes with infill variations, the triangular pattern excelled with a 0.97% increase over concentric and 6.12% over hexagon patterns. Honeycomb results indicate a 59.6% increase for (PLA/1.0%CNTs) and a 0.48% increase for (PLA/2.0%CNTs) compared to the matrix. This study highlights 3D printing parameters, emphasizing the effectiveness of the triangular pattern and the enhanced strength with the addition of CNTs, providing insights to enhance products manufactured through Additive Manufacturing.

Excessive activation of frog eggs, so called overactivation, can be initiated by strong oxidative stress, leading to expedited calcium-dependent non-apoptotic cell death. Overactivation also occurs spontaneously, albeit with a low frequency, in natural populations of spawned frog eggs. Currently, cytological and biochemical events of the spontaneous process are not characterized. In the present study, we demonstrate that spontaneous overactivation of Xenopus frog eggs, similarly to oxidative stress- and mechanical stress-induced overactivation, is characterized by the fast and irreversible contraction of the egg’s cortical layer, increase in the egg size, depletion of intracellular ATP, drastic increase in the intracellular ADP/ATP ratio, and degradation of M phase-specific cyclin B2. These events manifest in eggs in the absence of caspase activation within just one hour of triggering overactivation. Importantly, large amounts of ATP and ADP leak from the overactivated eggs, indicating that plasma membrane integrity is compromised in these cells. The rapture of the plasma membrane and acute depletion of intracellular ATP define explicitly necrotic cell death. Finally, we report that egg overactivation can occur in the frog’s genital tract. Our data argue that mechanical stress may be a key factor promoting egg overactivation during natural spawning in frogs.

Steel slag and GBFS are wastes generated during the steel and iron smelting process, characterized by their considerable production rates and extensive storage capacities. After grinding, they are often used as supplementary cementitious materials. However, the intrinsic slow hydration kinetics of steel slag-GBFS cementitious material (SGM) when exposed to a pure water environment result in prolonged setting times and diminished early-age strength development. The incorporation of modifiers such as gypsum, clinker, or alkaline activators can effectively improve the various properties of SGM. This comprehensive review delves into existing research on the utilization of SGM, examining their hydration mechanisms, workability, setting time, mechanical strengths, durability, and shrinkage. Critical parameters including the performance of base materials (water-to-cement ratio, fineness, and composition) and modifiers (type, alkali content, and dosage) are scrutinized to understand their influence on the final properties of the cementitious materials. The improvement mechanisms of various modifiers on properties are discussed. This the promotes resource utilization of industrial solid wastes and provides theoretical and technical support for the application of SGM.

The construction industry generates significant CO2 emissions, and rebar is a major contributor to this environmental impact. Extensive research has been conducted to address this issue. Recent advancements have introduced algorithms to reduce rebar waste and consumption, demonstrating the feasibility of achieving near-zero rebar cutting waste (N0RCW) by considering special-length rebars. However, conventional lap splices, the most common rebar joint method, consistently consume excessive rebar quantities despite extending beyond their mandated zones. Conversely, couplers eliminate rebar lengths required for lapping splices, reducing the usage of rebar. Applying special lengths and couplers in heavily loaded structures like diaphragm walls can significantly reduce rebar usage and cutting waste, consequently reducing CO2 emissions and associated costs. This study aims to optimize rebar consumption and sustainability in diaphragm wall structures by integrating mechanical couplers with a special-length rebar approach. A case study confirmed a substantial reduction in purchased rebar usage (17.95% and 5.38%) and carbon emissions (15.24% and 2.25%) compared to the original design and previous study, respectively. Broadly implementing the proposed method across various buildings and infrastructure projects could further multiply these benefits, fostering the achievement of SDGs adopted by the United Nations for sustainable construction.

PURPOSE: The aim of this study was to identify the incidence of early mechanical failure in the first post-surgical year in patients who had undergone spinal surgery, and to assess the related risk factors. METHODS: Retrospective observational study of a prognostic cohort was conducted at an orthopaedic hospital, examining all patients with spine degenerative disease who consecutively underwent arthrodesis surgery between March 2018 and March 2019. The incidence of postoperative mechanical failure during the first year was calculated as primary outcome; the time between the date of the implant surgery and diagnosis of the mechanical failure was calculated as secondary outcome. RESULTS: A total of 237 patients were identified for statistical analysis. The median age of the group of patients was 47 years (IQR of 44), and 66.6% were female. The incidence of mechanical failure in the first postoperative year was 5.1% overall with 12 events and the median time between surgery and the need for revision surgery was 5 months (IQR=7.75). ASA score (OR= 2,39; p=0.134), duration of the surgical procedure (OR=1,27; p=0,006) and inability to walk at discharge (OR=7,86; p=0,072) were independent risk of factor associated with the mechanical failure. CONCLUSION: Higher ASA score and longer duration of surgery are risk factors for mechanical failure in the first year in patients who had undergone spinal surgery and must be carefully considered when planning spinal surgery. During hospitalization, recovery of ambulation must be encouraged to prevent mechanical failure. All these factors are useful in identifying patients with a closer follow-up is needed.