The low coefficient of thermal expansion of Invar 36 represents a significant consideration in light of its potential effects, particularly in industrial applications where thermal stability is of paramount importance. In light of this, a three-step heat treatment was employed, to reduce the thermal expansion coefficient, and enhance the thermal dimensional stability. The ingots produced by vacuum induction melting were subjected to a warm rolling process at 900 °C, followed by a three-step heat treatment consisting of water quenching at 850 °C, tempering at 350 °C with a holding time of 1 hour, and aging at 100 °C for 24 hours. This process enabled the coefficient of thermal expansion to remain almost unchanged, exhibiting values between 0.5 and 0.6 x10-6/°C up to 150 °C. Following the heat treatment, the total elongation increased up to 40% as a natural consequence of the reduction of residual stresses, while a slight decrease in tensile strength was observed. The implementation of a three-step heat treatment process has facilitated an enhancement of the soft magnetic property, which has exhibited a decline in coercivity and an increase in saturation magnetization. As a consequence, three-step heat-treated invar 36 alloys are emerging as a potential candidate for utilization in the aerospace and precision electronics industries, given their satisfactory physical and mechanical characteristics.

The new unique technology for granulation of metals and nonmetallic melts is presented in the paper. It was created on the newly developed controlled film flow disintegration with rapid cooling of the droplets and solidified granules in amorphous state. Three new phenomena discovered by us created the base for 3 different methods for granulation of metals and nonmetallic melts in a wide range of granules’ sizes. Electromagnetic resonance method allows producing granules of metals in the range of 1 mm and over. The soliton-like vibrational regime is available for production of any granulation material in the range 0.1-1 mm. Moreover, the shockwave regime is applicable for producing particles from 10 micrometers by size. All methods produce particles of the stated size with a narrow distribution by size: deviation from the average size no more than 50%. The other known methods do not produce granules with such high cooling rate, which can realize the amorphous state and cannot regulate size of particles in such bright but narrow range from 10 micrometers to 1-2 mm.

The combined use of lasmiditan and triptan is unexplored in medical literature. This study aimed to investigate whether the intake of lasmiditan following triptan improves migraine pain. Following triptan intake, if headache relief was less than 50% at 1 hour, patients took 50 mg lasmiditan within 2 hours of migraine onset. Patients recorded headache intensity and adverse events(AEs) caused by lasmiditan at 1, 2, and 4 hours after intake of additional 50 mg of lasmiditan. A significant reduction in pain scale was observed post 50 mg lasmiditan intake (p < 0.001, t-test). Pain relief was reported for 32 migraine attacks (80%) at 1 hour after additional lasmiditan intake. Although AEs were observed in 63% of the patients who took an additional lasmiditan, most were mild and resolved 1 hour after lasmiditan intake. Our study revealed the significant headache reliefs provided by an additional lasmiditan for patients who did not achieve satisfactory results following initial triptan intake for treating migraine. The AEs associated with this treatment strategy were mild and lasted for a short term. This study suggested that the combination of triptan and lasmiditan is promising for the treatment of migraine and should be studied in a randomized placebo-controlled trial.

The study of different forms of preconditioners for solving a system of nonlinear equations, by using Newton’s method, is presented. The preconditioners provide numerical stability and rapid convergence with reasonable computation cost, whenever chosen accurately. Different families of iterative methods can be constructed by using a different kind of preconditioners. The multi-step iterative method consists of a base method and multi-step part. The convergence order of base method is quadratic and each multi-step add an additive factor of one in the previously achieved convergence order. Hence the convergence of order of an m-step iterative method is m + 1. Numerical simulations confirm the claimed convergence order by calculating the computational order of convergence. Finally, the numerical results clearly show the benefit of preconditioning for solving system of nonlinear equations.

Running on a non-motorized, curved-deck treadmill is thought to improve gait mechanics. It is not known, though, if the change in gait carries over to running on a motorized treadmill or level ground. To determine the effect of running on a curved non-motorized treadmill (CNT) on gait characteristics measured during a subsequent bout of running on a traditional motorized treadmill (TMT). Sixteen healthy college-aged participants, age (mean±SD) 20.4±1.6 years volunteered to have their gait analyzed while running on a TMT and CNT. After familiarization and warm-up on both treadmills, each subject completed five, 4-minute bouts of running alternating between traditional motorized and curved non-motorized treadmills: TMT-1, CNT-1, TMT-2, CNT-2, and TMT-3. Variables of interest included step length (m), stride length (m), imbalance score (%), and step angle (°) and were measured using Optogait gait analysis equipment. Differences in gait char acteristics among TMT-1, TMT-2, and TMT-3 can be attributed to running on the CNT. The results show that running on a CNT resulted in significant changes in gait characteristics. These findings suggest that running on a CNT can significantly alter gait characteristics may result in improvements in running gait that persist to subsequent running on a TMT.

Global warming is increasing the frequency and intensity of compound drought-heat events (CDHEs), potentially leading to larger and more extreme fire seasons in mesic forests. Wildfire activity in subtropical China, under the influence of monsoonal rainfall, was historically limited to dry winters and rare in rainy summers. Here we seek to test that this area is on the brink of a major change in its fire regime characterized by larger fire seasons, extending into the summer, leading to increases in burned area. We analyze fire activity in Chongqing Municipality (46,890 km2), an important area in subtropical China hosting the Three Gorges Reservoir Area. We observed significant increases in summer forest fires under anomalous dry-hot summer conditions, where total burned area was 3-6 higher than the historical annual mean (largely confined to the winter season). Vapor pressure deficit, an indicator of hot and dry conditions, was a strong predictor of fire activity, with major wildfires occurring on days where VPD was higher than 3.5kPa. Results indicate that major wildfire activity may occur in the area as a result of climate change, unless strong fire prevention policies are implemented.

Linear state estimation (SE) formulation under a rectangular coordinate system has been proved to be applicable for real-time distribution network management. Micro phasor measurements’ model can be accommodated into this kind of SE easily. However, voltage magnitude, active power and reactive power measurements are transformed to linear measurements with large node voltage error. To cope with this issue, a linear state estimation under a polar coordinate system is adopted at the first stage to obtain accurate enough complex node voltage, and then nonlinear measurements are transformed to be linear with complex node voltage. At the second stage, linear SE under a rectangular coordinate system can be adopted to satisfy more strict network constraints. The proposed two-stage linear SE is validated on balanced 14, 33, 70,84, 119, 135 nodes network and IEEE 13, 34, 37,123 unbalanced test feeders.

Cochlear implantation is the therapy used for patients with severe to profound sensorineural hearing loss. For the success of the surgery, it is important that each surgical step is performed with meticulous precision, starting from the correct patient’s position on the operating table. In elderly or obese patients, this can be difficult to achieve due to cervical rigidity. In these cases, the orthopedic position is an excellent choice to perform a mastoidectomy accurately, ensuring a safe procedure and avoiding unpleasant complications.

The paper describes problems with the current additive manufacturing chain before considering additive manufacturing as part of a modern manufacturing chain. Additive manufacturing can be used for near net-shape for finishing, for repair or for adding special features which cannot be made with traditional manufacturing. This paper describes how STEP-NC deals with these different scenarios in terms of accuracy, multi-material and variation of slice direction. The possibilities of multi-material objects also raises questions about the design of such objects and how these need to be handled by an advanced controller. The paper also describes non-planar slicing. Curved direction and cylindrical direction are shown to improve the accuracy of curved structure additive manufacturing. STEP-NC using boundary representation has better capability of depicting complex internal structures for additive processes. By using exact model of the final product represented by STEP-NC, the paper demonstrates improvements in data size reduction, slicing accuracy, and precise manipulation of internal structure.

In this research paper, a novel high step up dc-dc converter with a coupled inductor and voltage doubler circuits is proposed. The converter achieves a high step up voltage gain with an appropriate duty ratio and low voltage stress on the power switches. Also, the energy which is stored in the leakage inductor of the coupled inductor can be recycled to the output. The operating principles and the steady state analysis of the proposed converter are discussed in detail. Finally, a prototype circuit of the proposed converter is implemented in the laboratory in order to verify the performance of the proposed converter.

Graphene oxide was synthesized by a one-step environmentally friendly mechanochemistry process directly from graphite and characterized by Raman, FT-IR and UV/vis spectroscopies, Atomic Force Microscopy, X-ray Diffraction, Scanning Electron Microscopy, Energy-Dispersive X-ray Spectroscopy and Thermogravimetric Analysis. Spectroscopic analysis shows that the functional groups and oxygen content of the synthesized material are comparable with those of graphene oxide synthesized by other previously reported methods (Hummers). Thermogravimetric analysis reveals thermal stability up to 400 °C.

Using data from the Swedish National Diabetes Register, this study examines the gender disparity among patients with type I diabetes who have experienced a specific cardiovascular complication, while exploring the association between weight variability, age group, and gender. Fourteen cardiovascular complications have been considered. This analysis is conducted by using three-way correspondence analysis (CA) which allows for the partitioning and decomposition of Pearson’s three-way chi-squared statistic. The dataset comprises of information organized in a data cube, detailing how weight variability among these patients correlates with a cardiovascular complication, age group and gender. The three-way CA method presented in this paper allows for one to assess the statistical significance of the association between these variables and to visualize this association, highlighting the gender gap among these patients. It is worth noting that the association between weight variability, age group, and gender varies among different types of cardiovascular complications.

The paper primarily demonstrates that the three internal triangles formed by connecting any point on a midsegment with the vertices of a generic triangle satisfy the geometric Proof of the Pythagorean theorem in Euclidean geometry. Moreover, this study elucidates the Pythagorean relationships inherent within three-dimensional geometric constructs resulting from the arrangement of three-dimensional spatial triangles. This geometric relationship, akin to a generalized extension of the Pythagorean theorem, unveils a unique spatial region characterized by this harmonious area interrelation among triangles.

Background/Objectives: Population aging is rapidly increasing, and the importance of preventive medicine has been stressed. Health checkup, diet, and exercise are of paramount importance. This study aimed to evaluate the effectiveness of a personalized dual-task intervention that combined exercise with cognitive tasks in improving physical and cognitive functions among independently living elderly individuals. Methods: Participants were aged >65 years who were mostly independent in their activities of daily living, divided into 2 groups. The group receiving the 20-min robot-assisted session was compared to the group receiving traditional functional restoration training. This randomized trial assessed the impact of this intervention on the 30-s chair stand test score and Montreal Cognitive Assessment-Japanese version score of the participants. Results: Both scores significantly improved in the intervention group, indicating enhanced lower-limb function and cognitive capabilities. Conclusions: These findings suggest that integrating cognitive tasks with physical exercise can be a potent strategy to improve overall well-being in the elderly, offering valuable insights for designing comprehensive preventive health programs tailored to this demographic.

In this paper, an analytical form of the Unit Step Function (or Heaviside Step function) is presented. This important function constitutes a fundamental concept of Operational Calculus and is also involved in many other fields of applied and engineering mathematics. In particular, Heaviside Step Function is performed in a very simple manner by the use of a finite number of standard operations, as the summation of six inverse tangent functions. The novelty of this work when compared with other analytical expressions, is that the proposed exact formula contains two arbitrary single - valued continuous functions which satisfy only one restriction. In addition, the proposed representation is not exhibited in terms of miscellaneous special functions, e.g. Bessel functions, Beta function, Logistic function. Besides, it is neither the limit of a function, nor the limit of a sequence of functions with point – wise or uniform convergence. Hence, this formula may be much more practical, flexible and useful in the computational procedures which are inserted into Operational Calculus techniques and other engineering practices.

The quest for accurate and more efficient methods for solving periodic/oscillatory problems is gaining more attention in recent time. This paper presents the construction and implementation of a family of exponentially–fitted Obrechkoff methods. A single–step Obrechkoff method involving terms up to the fourth derivatives was used as the base method. We also present the stability and convergence properties of the constructed family of methods. Two numerical examples were use to illustrate the performance of the constructed methods.

Multi-step ahead streamflow forecasting is of practical interest for the operation of hydropower reservoirs. We provide generalized results on the error evolution in multi-step ahead forecasting by conducting several large-scale experiments based on simulations. We also present a multiple-case study using monthly time series of streamflow. Our findings suggest that some forecasting methods are more useful than others. However, the errors computed at each time step of a forecast horizon within a specific case study strongly depend on the case examined and can be either small or large, regardless of the forecasting method used and the time step of interest.

Freezing of Gait (FoG) is a disabling motor complication in Parkinson’s disease (PD), affecting approximately 50% of advanced PD patients. It is characterized by sudden and transient inability to initiate or maintain walking, leading to falls and reduced quality of life. This study investigates the relationship between white matter integrity and step initiation impairments in FoG. Forty-three PD patients (26 with FoG) underwent diffusion-weighted imaging to assess white matter DTI metrics and kinematic analysis during step initiation tasks. Multiple regression analyses were conducted to explore the connection between white matter tract integrity and step initiation behavior. The multiple regression analysis shows that (1) Right Inferior Longitudinal Fasciculus RD explained 31% of APA duration’s variance; (2) Corpus Callosum Forceps Major explained 25% of the step length's variance. There was a positive correlation between the Right Inferior Longitudinal Fasciculus RD and APA duration and a negative correlation between Corpus Callosum Forceps Major RD and step length. The findings suggest that compromised white matter integrity in RILF and CC contributes to impaired motor control during step initiation in FoG. These regions are critical for inhibitory control and interhemispheric coordination, crucial for APA execution and step length regulation.

In this paper, a new full-Newton step feasible interior point method for convex quadratic programming is presented and analyzed. The idea behind this method is to replace the complementarity condition with a non-negative variable weight vector and use the algebraic equivalent transformation for the obtained equation. Under the selection of appropriate parameters, the quadratic rate of convergence of the new algorithm is established. In addition, the iteration complexity of the algorithm is obtained. Finally, some numerical results are presented to demonstrate the practical performance of the proposed algorithm.

In this nano era, nanomaterials and nanostructures are popular in developing novel functional materials. However, the combinations of nanoproducts with materials at micro and macro scale can open new routes for conceiving novel materials with an improved or even new functional performances. In this study, a brand-new hybrid, containing both nanofibers and particles having a microsize, was fabricated using a sequential electrohydrodynamic atomization (EHDA) process. Firstly, the microparticles loaded with drug (berberine hydrochloride, BH) molecules in the cellulose acetate (CA) were fabricated using a solution electrospraying process. Later, these microparticles were suspended into a co-dissolved solution containned BH and a hydrophilic polymer (polypyrrolidone, PVP), and were co-electrospun into the nanofiber/microparticle hybrids. The EHDA processes were clearly recorded, and the resultant products showed a typical hybrid topography, with microparticles distributed all over the nanofibers, which was demonstrated by SEM assessments. FTIR and XRD demonstrated that the components within the hybrids were presented in an amorphous state and have fine compatibility with each other. In vitro dissolution tests verified that the hybrids were able to provide the designed dula-step drug release profiles, a combination of the fast release step of BH from the hydrophilic PVP nanofibers through an erosion mechanism and the sustained release step of BH from the insoluble CA microparticles via a typical Fickian diffusion mechanism. The present protocols pave a new way for developing trans-scale functional materials.

The three-phase separator was perforated after four years’ service. The perforation position is at the bottom of the vessel under the baffle plate in an oil transfer station. The cause of perforation was investigated by chemical analysis using a direct-reading spectrometer, microstructure examined by optical microscope(OM), and lab simulated corrosion experiments by electrochemical workstation, and the corrosion products examined with scanning electron microscopy(SEM), energy dispersive spectrometer(EDS) in this paper. The analyses indicated that the coating at the base of the pressure vessel failed and this led to the direct exposure of the carbon steel plate to the corrosive medium. The electrical contact between the carbon steel and the stainless steel, sets up a galvanic cell that accelerated the corrosion of the pressure vessel which eventually led leads to the perforation.

This article provides exact analytical formulae for various kinds of rainbow step barrier options. These are highly flexible and sophisticated multi-asset barrier options based on the following principle : the option life is divided into several time intervals on which different barriers are monitored w.r.t. different underlying assets. From a mathematical point of view, new formulae are provided for the first passage time of a multidimensional geometric Brownian motion to a boundary defined as a step function. The article shows how to implement the obtained valuation formulae in a simple and very efficient manner. Numerical results highlight a strong sensitivity of rainbow step barrier options to the correlations between the underlying assets.

Photovoltaic (PV) energy has been a preferable choice with the rise in global energy demand, as it is a sustainable, efficient, and cost-effective source of energy. Optimizing the power generation is necessary to fully utilize the PV system. Harvesting more power uses cascading of impedance source converters taking input from low-voltage PV arrays which requires multiple maximum power point tracking (MPPT) controllers. To solve this problem, a three-level inverter topology with a new PV arrangement, offering a smaller size with lower cost is designed in this article. The design criteria for parameters are discussed with the help of the small signal analysis. In this paper, three PV arrays are used to harvest maximum energy, which requires only one MPPT controller and employs a modified perturb and observe (P&O) algorithm, being faster, highly efficient, and reducing the computational burden of the controller. Moreover, a three maximum power points tracker algorithm, which perturbs one parameter and observes six variables, is designed for the selected converter topology. This MPPT algorithm offers better dynamics and is highly efficient with a conversion efficiency of 99.2% during uniform irradiance and 97% efficiency during variable irradiance conditions.

The article introduces a new solution approach to grid-connected single-stage three-phase PV inverter whereby a dc-link voltage can successfully achieve the desired performance. As a single-stage, the variable output of perturb and observe maximum power point tracking (P&O based-MPPT) is fully utilized as dc-link voltage reference in inverter control scheme. As a result, it is challenging for the dc-link voltage to preserve energy balance by tracking its variable dc-link voltage reference under unpredictable environmental changes. To overcome this challenge, an adaptive reference proportional-integral (ARPI) controller, self-tuning, is designed and implemented to compel the dc-link voltage tracking its voltage reference to be equal as closely as possible; hence, the capability of the dc-link under abnormal events substantially guarantees the best energy balance and transient performance enhancement. To verify the validity of the method, simulation results for multiple events scenarios on 250 KW single-stage grid-connected PV systems show the effectiveness of the ARPI controller compared with PI controller.

Citizens face online privacy threats from social media, organisations and governments. Privacy-enhancing tools (PETs) can help people to preserve their privacy, but the uptake of these is limited. We developed a conceptual framework for privacy self-protection, using a classification framework of four distinct privacy threats and our own novel staged model of PET adoption requisites. Through an expert survey (N = 12) and a lay user survey (N = 500), we identified suitable PETs for non-expert users and identified potential barriers to PET adoption. Based on the studies and our theoretical framework, we then developed and implemented a PET decision support tool called PEDRO, and conducted expert evaluations (N = 10).

Ice accumulation poses considerable challenges in transportation, notably in the domain of general aviation. The present study combines the strengths and limitations of conventional aircraft de-icing techniques with the emerging trend toward all-electric aircraft. The study aims to utilize laser-induced graphene (LIG) technology to create a multifunctional surface, seamlessly integrating hydrophobic properties with efficient electrical heating to mitigate surface icing effectively. We investigated the utilization of a 10.6 μm CO2 laser for direct writing on polyimide (PI), a widely-used insulating encapsulation material. From the thermomechanical perspective, our initial analysis using COMSOL Multiphysics software revealed that when the laser power P exceeds 5 W, the PI substrate experience ablative damage. The experimental results show that when P ≤ 5W, an increase in power has a positive impact on the quality, surface porosity, roughness reduction, line-spacing reduction, and water contact-angle enhancement of the graphene. Conversely, when P > 5 W, higher power negatively affects both the substrate and the graphene structure by inducing excessive ablation. However, it influences the graphene line height positively and is consistent with overall experimental-simulation congruence. Furthermore, the incorporation of high-quality graphene resulted in a surface that exhibited higher contact angles (CA > 120°), lower energy consumption, and higher heating efficiency compared to the use of traditional electrically heated materials for anti-icing applications. The potential applications of this one-step fabrication method extend across various industries, particularly aviation, marine engineering, and other ice-prone domains. Moreover, the method has extensive prospects for addressing pivotal challenges associated with ice formation and serves an innovative and efficient anti-icing technology.

Sleep quality is known to affect automatic and executive brain functions such as gait control and cognitive processing. This study aimed to assess the effect of dual tasks on gait spatiotemporal parameters among young adults with good and poor sleep quality in the United Arab Emirates. In total, 65 young adults with a mean age of 21.1±2.5 were assessed for gait analysis during single-task and dual-task conditions. The participants’ sleep quality was assessed using the Pittsburgh Sleep Quality Index (PSQI), and gait was assessed using the BTS Gaitlab System. The participants were asked to walk at natural speed as a single-task condition, followed by walking while performing a cognitive task as a dual-task condition. The parameters assessed included the gait velocity (m/s), cadence (steps/min), step width (m), and stride length (m). The DTC on each gait parameter was calculated. The Mann–Whitney U test was used to compare the differences in the DTC on gait variables between the good and poor sleep quality groups, and the Spearman correlation test was used to assess the correlation between total PSQI scores and the DTC. At a significance level of p<0.05, a significant difference in cadence between the two sleep quality groups was observed, in addition to a positive correlation between sleep quality and the DTC effect on gait mean velocity, cadence, and stride length. Our findings also revealed a greater DTC on participants with poorer sleep quality. These findings contribute to our understanding of the significance of sleep quality in gait performance while multitasking in younger populations.

This paper presents a concise mathematical framework for investigating both feed-forward and backward process, during the training to learn model weights, of an artificial neural network (ANN). Inspired from the idea of the two-step rule for backpropagation, we define a notion of F_adjoint which is aimed at a better description of the backpropagation algorithm. In particular, by introducing the notions of F-propagation and F-adjoint through a deep neural network architecture, the backpropagation associated to a cost/loss function is proven to be completely characterized by the F-adjoint of the corresponding F-propagation relatively to the partial derivative, with respect to the inputs, of the cost function.

In current study we have obtained Co2FeSi-glass coated microwires with different geometrical aspect ratio, ρ = d/Dtot (diameter of metallic nucleus, d and total diameter, Dtot). The structure and magnetic properties are investigated at a wide range of temperature. XRD analysis illustrates a notable changing in the microstructure by increasing the aspect ratio of Co2FeSi glass coated microwires. Amorphous structure is detected for the sample with the lowest aspect ratio (ρ = 0.23), whereas a growth of crystalline structure is observed in the other samples (aspect ratio ρ = 0.30 and 0.43). This change at the microstructure properties correlates with dramatic changing in magnetic properties. For the sample with the lowest ρ -ratio, non-perfect square loops are obtained with low normalized remanent magnetization. A notable enhancement in the squareness and coercivity are obtained by increasing ρ -ratio. Changing the internal stresses strongly affects the microstructure, resulting in a complex magnetic reversal process. The thermomagnetic curves show large irreversibility for the Co2FeSi with low ρ -ratio. Meanwhile, if we increase the ρ -ratio, the sample shows perfect ferromagnetic behavior without irreversibility. The current result illustrates the ability to control the microstructure and magnetic properties of Co2FeSi-glass-coated microwires by changing only their geometric properties without performing any addition heat treatment. The modification of geometric parameters of Co2FeSi glass-coated microwires allows to obtain microwires which exhibit an unusual magnetization behavior that offers opportunities to understand the phenomena of various types of magnetic domain structures, which is essentially helpful for designing sensing devices based on thermal magnetization switching.

This paper presents a comprehensive review that highlights the characteristics of non-isolated step-up converters based on high boost voltage lifting techniques. The paper categorises the high boost techniques: multistage/multilevel, switched capacitor, voltage multiplier, voltage lift, switched inductor, and magnetic coupling. The paper also discusses in detail the advantages and disadvantages for each category such as cost, complexity, power density, reliability and efficiency. The number of passive and active components, voltage gain, voltage stress, switching frequency, efficiency and power rating are also compared. Although the paper considers coupling inductors in the context of the non-isolated converter, the focus of the entire article is on the non-isolated high voltage step-up techniques. The key contribution in this paper is the review of high boosting techniques rather than the DC /DC converters. This allows divergence of new ideas and new power converters that will help provide highly efficient and flexible power converters for several applications where the sending end voltage is very low as photovoltaic systems. In addition, many applications and control techniques of DC/DC converters are summarised in this paper.

We search for limit cycles in the dynamical model of two-species chemical reactions that contain seven reaction rate coefficients as parameters and at least one third-order reaction step, that is, the induced kinetic differential equation of the reaction is a planar cubic differential system. Symbolic calculations were carried out using the Mathematica (or, Wolfram language) mathematical program package, and it was also used for the numerical verifications to show the following facts: the kinetic differential equations of these reactions each has two limit cycles surrounding the stationary point of focus type in the positive quadrant. In the case of Model 1, the outer limit cycle is stable and the inner one is unstable that appears in a supercritical Hopf bifurcation. Moreover, the oscillations in a neighborhood of the outer limit cycle are slow-fast oscillations. In the case of Model 2, the outer limit cycle is unstable and the inner one is stable. With another set of parameters, the outer limit cycle can be made stable and the inner one unstable.

The seasonally adjusted civilian labor force participation rate, the sum of employed and unemployed persons as a percentage of the civilian non-institutional population, is analysed in the general to specific modelling framework with a saturating set of step indicators from January 1977 through June 2018. The results indicate that, ceteris paribus, the rise in the ratio of women to men in the labor force in addition to positive demographic movements can largely account for the rise in the labor force participation rate up to January 2000. Subsequently, the aging population helps to explain the decline. Recessions play a transitory role.

Three-dimensional graphene (3DG) sponge has attracted increasing attention because it combines the unique properties of cellular materials and the excellent performance of graphene. The preparation of 3DG sponge depends mainly on the self-assembly of graphene oxide sheets. Here, we demonstrate facile fabrication of 3DG sponge with a large-scale and ordered porous structure, exploiting the liquid crystals of large graphene oxide (LGO) and ultralarge graphene oxide (ULGO) sheets. The resulting materials exhibit a low density, high porosity and elasticity. Our work explores a new strategy for organizing the ordered alignment of controlled large GO sheets and exploring the relationship between the microstructures and mechanical properties of 3DG sponge.

Nucleoside analogs are commonly used drugs for the treatment of cancer and viral infections. Nucleoside deoxyribosyltransferase (NDT) is one of the key enzymes required for the biosynthesis of deoxynucleotides. The feasibility of biochemical transformation processes is usually greatly dependent on the cost of biocatalysts. Therefore, immobilizing and reusing biocatalysts is an approach to be considered to bring biotransformations closer to industrial feasibility, since it not only allows enzymes to be reused but can also improve their stability under several reaction conditions. In this work, histidine tags have been successfully fused to a Nucleoside deoxyribosyltransferase from Lactobacillus reuteri (LrDNT), which has been produced in a bench-scale reactor using a facile araBAD promoter-based protein expression system in an industrial microorganism, the E. coli BL21(DE3) strain. The overexpressed LrNDT was bound to a nickel-chelating agarose affinity chromatography medium via a one-step purification and immobilization process with a 99% yield, retaining about 97% of its initial activity. The optimal conditions for the immobilized LrNDT maintain high enzyme activity within the range of 20-45°C and pH 6.0-7.5. Finally, the immobilized enzyme reactor (IMER) of LrNDT was applied for the continuous-flow biosynthesis of 2'-deoxyadenosine and retained 90% of its activity after 16 hours, providing a theoretical basis for the industrial production of nucleoside analogs.

This paper proposes a novel symmetrical active-switched coupled-inductor high-step-up DC/DC converter. A new active-switched coupled inductor is used to allow much higher voltage gain of the proposed converter. The symmetrical circuit structure of the proposed converter evenly divides large input currents and reduce input current ripple by operating in interleaved mode so power density is increased. The switches also have low voltage stress. The operating principle and design considerations for the converter topology are described. The proposed converter with an input voltage of 40 V, an output voltage of 400 V and an output of 1000 W at a switching frequency of 50 kHz is implemented. The simulations and experimental results are thus depicted to verify the theoretical analysis. The highest efficiency is 95.5% at 200 W measured by using a HIOKI 3390. Consequently, the proposed converter is suitable for renewable energy generation systems that require high power, high voltage gain and high efficiency.

Environmental regulation has dual effects on water resource utilization performance through various channels such as the "three red lines" and the "Porter hypothesis". Based on the detailed analysis of the impact path of environmental regulation on water resource utilization performance, the two-step system GMM method was adopted to test the dual effects of environmental regulation on water resource utilization performance by using panel data of 30 provinces and cities from 2004 to 2020. The results show that: (1) Environmental regulation has a significant direct impact on water resource utilization performance, and is currently in the stage of positive relationship of an inverted u-shaped relationship. (2) Environmental regulation has a significant indirect impact on water resource utilization Environmental regulation has dual effects on water resource utilization performance through various channels such as the "three-red lines" and the "Porter hypothesis". In accordance with a detailed examination of the influence path of environmental regulation on the performance of water resource utilization, the double effects of environmental regulation on water resource utilization performance were examined using panel statistics from 30 provinces and cities from 2004 to 2020 using the two-step system GMM approach. The results demonstrate that: (1) Environmental regulation has a direct effect on water resource utilization performance which is currently in the stage of the positive relationship of an inverted u-shaped relationship. (2) The influence of environmental regulation on water resource utilization performance through government intervention and industrial structure adjustment is indirect, among which government intervention can significantly improve water resource utilization performance, while the growth of the tertiary industry as a percentage can lower water resource utilization performance. (3) Both direct and indirect impacts indicate that enhancing the efficiency of the use of water resources is sustainable, and the water resource utilization performance of the preceding period had a major positive impact over the present phase. Therefore, the paper sets out a few policy suggestions, such as choosing reasonable environmental regulation tools, actively guiding the market-oriented reform with constraints, and upgrading the industrial structure in a green way.

In this study, the degradable superhydrophobic Mg/P/Z/F/H (magnesi-um/poly(-caprolactone)/zinc oxide/1H,1H,2H,2H-perfluorodecyltriethoxysilane (PFDTES)/ heating process) composite materials were prepared through one-step method for enhancing the corrosion resistance of AZ91D magnesium alloys. Electrochemical measurements showed that Mg/P/Z/F/H materials significantly improved the corrosion resistance of magnesium alloys in 3.5 wt.% NaCl. The self-cleaning, adhesion and stability tests suggested that Mg/P/Z/F/H composite materials had well self-cleaning properties, good adhesion strength and stability in wet atmosphere.

To improve the voltage gain of step-up converters, cascaded technique is considered as a possible solution in this paper. By considering the concept of cascading two Z-source networks in a conventional boost converter, the converter takes the advantages of both impedance source and cascaded converters. However, by applying some modifications, the proposed converter provides high voltage gain while the voltage stress of switch and diodes are still low. Moreover, the low input current ripple of the converter makes it absolutely appropriate for photovoltaic applications in order to expand the lifetime of PV panels. After analyzing the operation principles of the proposed converter, simulation and experimental results of a 100W prototype are presented to verify the proposed converter performance.

This article presents a self balanced multistage DC-DC step-up converter for photovoltaic applications. Proposed converter topology is designed for unidirectional power transfer and provides a doable solution for photovoltaic applications where voltage is required to be stepped up without magnetic components (Transformer-less and Inductor-less). The output voltage obtained from renewable sources will be low and must be stepped up by using a DC-DC converter for photovoltaic applications. K diodes and K capacitors along with two semiconductor control switch are used in the K-stage proposed converter to obtain an output voltage which is (K+1) times the input voltage. The conspicuous features of proposed topology are i) Magnetic components free (Transformer-less and Inductor-less). ii) Continuous input current iii) Low voltage rating semiconductor devices and capacitors iv) Modularity v) Easy to add a higher number of levels to increase voltage gain vi) Only two control switches with alternating operation and simple control. The proposed converter is compared with recent existing transformer-less and Inductor-less power converter in term of voltage gain, number of devices and cost. The application of proposed circuit is discussed in detail. The proposed converter has been designed with rated power of 60W, input voltage is 24V, output voltage is 100V and switching frequency is 100 kHz. The performance of the converter is verified through experimental and simulation results.

Background: Scaffold (SCA) functionalization with aptamers (APT) provides adsorption of specific bioactive molecules on biomaterials surface. The aim of this study was to observe if SCA enriched with anti-fibronectin APT can favor coagulum (PhC) and osteoblasts (OSB) differentiation. Methods: 20 ug of APT was functionalized on SCA by simple adsorption. For PhC formation, SCAs were inserted into rat calvaria defects for 17 hours. Following proper transportation (Buffer solution-PB), OSB (UMR-106 lineage) were seeded over PhC + SCAs with and without APT. Cells and PhC morphology, PhC cell population, protein labelling and gene expression were observed in different time points. Results: The APT induced higher ALP and BSP immunolabeling in OSB. CD90, CD45 and CD44 expression was more detected in APT group than when scaffolds were not functionalized. Additionally, an enriched and dense fibrin network and different cell types were observed, with more OSB and white blood cells in PhC formed on SCA with APT. The gene expression showed higher TGF-β1 detection in SCA with APT. Conclusions: The SCA functionalization with fibronectin aptamers provides a selective expression of proteins related to coagulation pattern and osteo differentiation. Additionally, aptamers increase TGF-β1 gene expression, which is highly associated with improvements in regenerative therapies.

Microbe-plant interactions are linked with the core microbiota, and both the plant and the microbial partners depend on one other to thrive in nature. However, why and how the below-ground core microbiota become established aboveground is poorly understood. We tracked the movement of a probiotic Streptomyces endophyte throughout a managed strawberry ecosystem. Probiotics in the rhizosphere and anthosphere were genetically identical, yet these niches were segregated in space and time. The probiotic in the rhizosphere moved upward via the vascular bundle, relocated to aboveground plant parts, and protected against Botrytis cinerea. It also moved from flowers to roots, and among flowers via pollinators that were protected against pollinator pathogens. Our results reveal a solid evidence in tripartite interaction with Streptomyces exploiting plant and pollinator partners.

With quick improvement in the field of network, everything becomes online. Remote user authentication is a mechanism in which remote server verify the correctness of user over common or public channel. Remote user authentication can be Single server authentication or Multi server authentication. The disadvantage of single server authentication is that the user needs to recall user id and password for each service, he/she need to utilize, however it can overcome by Multi-server authentication in which user needs to register himself with Registration Center (RC) for the first run through and after that onwards he can utilize each service (which are given by servers, associated with RC) by recollecting only one user id and password. In this paper, we analyze Chen's authentication scheme (based on multi server authentication) and show that this scheme is vulnerable to password guessing attack, replay attack, RC spoofing attack, session key verification attack and perfect forward secrecy attack. In this Paper, we propose a biometric based remote user authentication scheme in multi-server environment. Proposed scheme is more secure and efficient as compared to chen's scheme\cite{23}.

Posttraumatic stress disorder (PTSD) and/or specific PTSD symptoms may evoke disordered eating and unhealthy lifestyles, resulting in adverse cardiometabolic events (e.g., hypertension and obesity) in certain groups, which may implicate the treatment of this complex condition. The diagnostic criteria of PTSD have lately expanded beyond the three common symptoms (intrusion, avoidance, and hyperarousal). Simultaneously, four-, five-, and six-dimensional structures of the Impact of Event Scale-Revised (IES-R), a popular PTSD measure, seem to be more robust than the original three-dimension structure. Within the context of COVID-19, this instrumental study used a convenience sample of 58 dental healthcare workers (HCWs) from Russia (mean age = 44.1±12.2 years, 82.8% females) to examine the criterion and predictive validity of two IES-R structures: the IES-R3 and the IES-R6 (with the added symptoms of numbing, sleep disturbance, and irritability). The subscales of the two IES-R structures expressed good internal consistency, strong correlations with the PTSD Symptom Scale (PSS), hypertension diagnosis, and high body mass index (BMI). In receiver-operating characteristic (ROC) curve analysis, all IES-R models perfectly predicted the PSS (all area under the curve (AUC) >0.9, p values <0.001). The IES-R, both hyperarousal subscales, and the IES-R3 intrusion subscale significantly predicted high BMI. Both avoidance subscales and the IES-R3 intrusion subscale, not the IES-R, significantly predicted hypertension. In conclusion, both IES-R structures can reliably measure PTSD symptoms. The IES-R, hyperarousal, and intrusion may be credible criterion variables for predicting high BMI within PTSD while the intrusion and avoidance subscales may reflect the cardiovascular consequences associated with PTSD more reliably than the IES-R itself. The IES-R subscales may predict cardiometabolic adversities in PTSD, signifying a need for proper assessment of lifestyle and the application of dietary and exercise interventions in order to lower physical morbidity in PTSD. Replicating the study in larger samples, which comprise different physical and mental conditions from heterogenous cultural contexts is pivotal to validate the results (e.g., in specific groups such as those with confirmed traumatic exposure and comorbid mood dysfunction).

The advancement of performance in the domain of flexible wearable strain sensors has become increasingly significant due to extensive research on laser-induced graphene (LIG). An innovative doping modification technique is required owing to the limited progress achieved by adjusting laser parameters to enhance LIG’s performance. By pre-treating with AgNO3, we successfully manufactured LIG with a uniform dispersion of silver nanoparticles across its surface. The experimental results for the flexible strain sensor exhibit exceptional characteristics, including low resistance (183.4 Ω), high sensitivity (426.8), a response time of approximately 150 ms, and a relaxation time of about 200 ms. Moreover, this sensor demonstrates excellent stability under various tensile strains and remarkable repeatability during cyclic tests lasting up to 8,000 s. Additionally, this technique yields favorable results in finger bending and hand back stretching experiments, holding significant reference value for preserving the inherent characteristics of LIG preparation in a single-step and in situ manner.

This experimental study probes the dynamic behaviour of a 3mm ABS sheet during positive mould vacuum-assisted thermoforming. In this process, the sheet undergoes large and fast deformations, caused by the applied vacuum and mechanical stretching by the mould. The objective is to elucidate the complexities of these large, rapid and non-isothermal deformations. The non-isothermal conditions are caused by the radiative heating of the sheet, convective heat loss to the surrounding air and conductive heat transfer from the sheet to the mould. Utilizing stereo Digital Image Correlation (DIC) in tandem with thermal imaging, the present study accurately maps the occurring displacement, strain and strain rate field in relation to real-time temperature variation of the material. The study progresses to observe the ABS material from the moment it contacts the mould until it conforms to a positive 250mm diameter semi-sphere cast aluminium mould. The DIC methods are validated by comparing thickness values derived from DIC’s principal strain directions to ultrasonic thickness gauge readings. This knowledge not only broadens the understanding of the thermo-mechanical behaviour of the material but also aids in optimizing process parameters for improved thickness uniformity in thermoformed products.

Individuals with Parkinson’s disease (PD) and freezing of gait (FOG) have a loss of presynaptic inhibition (PSI) during anticipatory postural adjustments (APAs) for step initiation. The mesencephalic locomotor region (MRL) has connections to the reticulospinal tract that mediates inhibitory interneurons responsible for modulating PSI and APAs. Here, we hypothesized that MLR activity during step initiation would explain the loss of PSI during APAs for step initiation in freezers. Thirty-four freezers were assessed in the ON-medication state. During a functional magnetic resonance imaging protocol of simulated APA task, we assessed beta of blood oxygenation level-dependent signal change of areas known to initiate and pace gait (e.g., MLR), in addition to PSI of the soleus muscle during APA for step initiation, and clinical (e.g., disease duration) and behavioral (e.g., FOG severity and APAs amplitude for step initiation) variables. A linear multiple regression model showed that MLR activity (R2=0.32, P=0.0006) and APA amplitude (R2=0.13, P=0.0097) explained together 45% of the loss of PSI during step initiation in freezers. Decreased MLR activity during a simulated APA task is related to a higher loss of PSI during APA for step initiation. Deficits in central and spinal inhibitions during APA may be related to FOG pathophysiology.

Usually, the two-bath dyeing process using disperse dyes and reactive dyes separately was employed for the dyeing of PC blends. The cost of the double bath, dyeing cycle, energy consumption and chemical consumption is quite higher than the one-step or single bath dyeing methods. In this study, the one-bath dyeing process using one kind of dye was investigated. Polyester cotton blends dyed in one-bath one-step dyeing methods with disperse dye after surface modifications of cotton by acetylation methods were studied. Surface modification of cotton was carried out using fibrous acetylation methods. The effect of acetic anhydride and time on percent acetyl content at room temperature was studied. Modified polyester/cotton was carried out in HTHP dyeing machine incorporates with different dye concentrations and dyeing temperature. Surface chemistry, thermal decomposition property and moisture regain of modified polyester/ cotton blend are evaluated. The color strength of the dyed fabrics and their fastness properties to washing, light, and rubbing as well as tear strength and abrasion resistance were evaluated. The effect of dye concentration and temperature color strength, tensile strength warp and weft direction was assessed. The optimum value for surface modification was obtained with a concentration of acetylation agent 16% and time of reaction 2.5 hours, gave percent acetylation of 34. An FTIR spectrum shows acetylation resonance. The experiment result of dyeing showed that the optimum value was obtained with dye concentration above 1% at a temperature of 120oC, warp tensile strength decreased by 12% and weft tensile strength was decreased by 9% from the control half-bleached fabric. Results of this study showed that a one-step one-bath dyed modified polyester/cotton blend with disperse dye fabric presents good fastness property compared with conventional two-bath dyed fabric as well as colour strength values.

In wireless sensor networks (WSNs), each sensor node can estimate the global parameter from the local data in distributed manner. This paper proposed a robust diffusion estimation algorithm based on minimum error entropy criterion with self-adjusting step-size, which are referred to as diffusion MEE-SAS (DMEE-SAS) algorithm. The DMEE-SAS algorithm has fast speed of convergence and is robust against non-Gaussian noise in the measurements. The detailed performance analysis of the DMEE-SAS algorithm is performed. By combining the DMEE-SAS with diffusion minimum error entropy (DMEE) algorithms, an Improving DMEE-SAS algorithm is proposed, in non-stationary environment where tracking is very important. The Improving DMEE-SAS algorithm can avoid insensitivity of the DMEE-SAS algorithm due to the small effective step-size near the optimal estimator, and obtain a fast convergence speed. Numerical simulations are given to verify the effectiveness and advantages of these proposed algorithms.

In this paper, the distribution of prime numbers is expressed based on proving the Riemann hypothesis. The relationship between three numbers, three, six, and nine, and the modality to the distribution of prime numbers, is one of the results of Riemann's zeta function. Prime numbers are classified into six groups of single-digit numbers. There are no prime numbers in groups of three, six, and nine. The groups are made based on the sum of the internal digits. And for each set, there is an angle in the complex plane. The distance between the prime numbers in each group has a regular pattern. This pattern is a multiple of the numbers three, six, and nine. According to Euler's number, for an angle of 60 degrees, the real part of the cosine is 1/2. Accordingly, all prime numbers are related to angles greater than 60 degrees to 90 degrees. As a result, based on the relationship between the golden spiral and the complex conjugate of the zeta function, the function in The 1/2 point becomes zero based on the prime numbers.

Three-dimensional transfer functions (3D TFs) are generally assumed to fully describe the transfer behavior of optical topography measuring instruments such as coherence scanning interferometers in the spatial frequency domain. Therefore, 3D TFs are supposed to be independent of the surface under investigation resulting in a clear separation of surface properties and transfer characteristics. In this paper we show that the 3D TF of an interference microscope differs depending on whether the object is specularly reflecting or consists of point scatterers. In addition to the 3D TF of a point scatterer, we will derive an analytical expression for the 3D TF corresponding to specular surfaces and demonstrate this as being most relevant in practical applications of coherence scanning interferometry (CSI). We additionally study the effects of temporal coherence and disclose, that in conventional CSI temporal coherence effects dominate. However, narrowband light sources are advantageous if high spatial frequency components of weak phase objects are to be resolved, whereas for low-frequency phase objects of higher amplitude the temporal coherence is less affecting. Finally, we present an approach that explains the different transfer characteristics of coherence peak and phase detection in CSI signal analysis.

Abstract: This study was aimed to determine the influence of the volume fraction of steel fibers and on fracture parameters of concrete. Fifty notched steel fiber reinforced concrete (SFRC) beams and ordinary concrete beams with dimensions of 100mm×100mm×515mm were cast and tested via three-point bending test. Among them, the type of steel fiber is milling type (MF), and the volume fraction of steel fiber added is 0%, 0.5%, 0.5%, 1.5%, 1.5%, 2%, respectively. The effects of the steel fiber volume fraction (VF) on the critical stress intensity factor (KIC), fracture energy (GF), the deflection at failure(δ0), the critical crack mouth opening displacement (CMODC) and the critical crack tip opening displacement (CTODC)were studied. Through the analysis of test phenomena and test data such as load-deflection (P-δ) curve, load-crack mouth opening displacement (P-CMOD) curve and load-crack tip opening displacement (P-CTOD) curve following conclusions are drawn: With the increase of steel fiber volume fraction, some fracture parameters increase gradually and maintain a certain linear growth. The gain ratio of fracture parameters increases significantly, and the gain effect is obvious. Through this law of growth, the experimental statistical formulas of fracture energy and critical stress intensity factor are summarized.

Atoms in Molecules (AIM), Natural Bond Orbital (NBO), and normal coordinate analysis have been carried out at the global minimum structures of TH₅⁺ (T = C/Si/Ge). All these analyses lead to a consistent structure for these three protonated TH₄ molecules. The CH₅⁺ has a structure with three short and two long C-H covalent bonds and no H-H bond. Hence, the popular characterization of protonated methane as a weakly bound CH₃⁺ and H₂ is inconsistent with these results. However, SiH₅⁺ and GeH₅⁺ are both indeed a complex formed between TH₃⁺ and H₂ stabilized by a tetrel bond, with the H₂ being the tetrel bond acceptor. The three-center-two-electron bond (3c-2e) in CH₅⁺ has an open structure, which can be characterized as a V-type 3c-2e bond and that found in SiH₅⁺ and GeH₅⁺ is a T-type 3c-2e bond. This difference could be understood based on the typical C-H, Si-H, Ge-H and H-H bond energies. Moreover, this structural difference observed in TH₅⁺ can explain the trend in proton affinity of TH₄. Carbon is selective in forming a ‘tetrel bond’ and when it does, it might be worthwhile to highlight it as a ‘carbon bond’.

This study presents an instant preview and analysis system implementation of intelligent stereo cameras (ISCs). A parameter optimization prototype adopted the instant preview and analysis system of the ISCs has been achieved the automatic alignment function, and obtained optimal stereo films with the automatic alignment function by adjusting gap and angle between dual cameras. The instant preview and analysis system of the ISCs with parameter optimization can enhance the quality of stereo films effectively and reduce filmed errors and save retouched cost and time in harsh filmed environment.

The Huaniushan lead-zinc-silver deposit is a hydrothermal sedimentary exhalative deposit (SEDEX). The mining area has complex geological conditions. The main tectonic structure in the area is the Huaheitan-Shuangfengshan Fault (F3), which controls the distribution of strata and magmatic rocks. Since the discovery of the Huaniushan Lead-zinc-silver polymetallic deposit, there are diverse understandings of the deposit's genesis and mineralization law, making it challenging to meet the geological interpretation requirements of the Huaniushan Lead-zinc-silver polymetallic deposit. Moreover, a single geophysical exploration method utilizes limited rock physical parameters, making it difficult to effectively characterize underground structures. The integrated exploration of multiple geophysical methods can effectively integrate the geophysical characteristics of different rock physical parameters, reducing the multiplicity and uncertainty of geophysical data inverse interpretation. The comprehensive interpretation of three-dimensional inversion based on various geophysical data, the construction of geological-geophysical models based on geological grounds, the establishment of hidden ore exploration and positioning, and the rapid evaluation of geophysical technology systems are the current development trends in mineral exploration. In light of this, this paper conducts research on the three-dimensional inversion interpretation of the heavy magnetoelectric exploration data of the Huaniushan sedimentary exhalative deposit lead-zinc-silver polymetallic deposit in the mining area and constructs a three-dimensional geological-geophysical model of the study area based on the obtained three-dimensional physical structure of the underground three-dimensional density, magnetization intensity, resistivity, and polarizability structure of the study area, in combination with the information of related geology and drilling holes. It comprehensively interprets the favorable mineralization parts in the study area.

Typically, a diesel generator on the merchant ship, composed of a wound rotor synchronous generator and a four-stroke diesel engine, supplies electrical power to various loads. Recently, shaft generators for merchant vessels are increasingly replacing diesel generators to reduce CO2 emissions through fuel efficiency improvement. In particular, permanent magnet generators replace induction generators due to their high-efficiency characteristics at light loads. The surface-mounted permanent magnet can be a suitable rotor topology due to the relatively short constant power range. This generator can also operate as a motor according to the propulsion mode, so minimizing the harmonics of the induced voltage and the torque ripple is necessary. This paper proposes an alternative NdFeB magnet pole topology combined with the modular step-skewed rotor. The step-skewed rotor affects to reduce higher-order harmonics, and the modular pole reduces the permanent magnet assembly process and harmonics in voltage and torque. A 2-D finite element method is used to evaluate the harmonics of induced voltage and torque pulsation for the proposed topology. The topology shows harmonic minimization effect by comparing the characteristics of three flatted-bottom magnets. Compared to the tapered bread-loaf magnet, voltage harmonics to the 100th component are almost the same, and the torque ripple is reduced by more than 12% at the same residual flux density. The analysis method is verified by comparing test and analysis results for prototype machines with similar specifications.

The class of A-stable symmetric one-step Hermite-Obrechkoff (HO) methods introduced in [1] for dealing with Initial Value Problems is analyzed. Such schemes have the peculiarity of admitting a multiple knot spline extension collocating the differential equation at the mesh points. As a new result, it is shown that these maximal order schemes are conjugate symplectic which is a benefit when the methods have to be applied to Hamiltonian problems. Furthermore a new efficient approach for the computation of the spline extension is introduced, adopting the same strategy developed in [2] for the BS linear multistep methods. The performances of the schemes are tested in particular on some Hamiltonian benchmarks and compared with those of the Gauss Runge-Kutta schemes and Euler-Maclaurin formulas of the same order.

Introduction: Transesophageal echocardiography (TEE) is a vital diagnostic tool in clinical prac-tice, particularly in transcatheter interventions where it aids in both pre-operative planning and intra-operative guidance. Traditional TEE probes often require general anesthesia due to patient discomfort. However, the development of miniaturized TEE probes presents a promising alter-native, enabling routine examinations and interventions with minimal sedation. This study evaluates the feasibility of performing a complete 2D/4D TEE protocol with the new 4D-mini-TEE probe in echocardiography departments and its application in transcatheter interventions. Methods: This prospective, observational study included 30 consecutive patients from two high-volume European hospitals (Interbalkan Medical Center, Thessaloniki, Greece, and Rennes University, France) undergoing TEE or transcatheter interventions. The new 4D-mini-TEE 9VT-D probe (GE Healthcare) was utilized. The quality of the images and the tolerance of the probe were assessed in the Cath lab during interventions and in the echocardiography department during routine TEE examinations. Results: Direct comparison of the 4D-mini-TEE probe with the standard 6VT-D probe, confirmed the excellent image quality of this new pediatric probe. Most of the patients required minimal sedation or local oropharyngeal anesthesia, with satisfactory tolerance reported. Most of the transcatheter procedures did not require general anesthesia and intubation, resulting in shorter procedural time. Both 2D and 4D imaging modalities offered adequate intra-operative guidance for transcatheter procedures. Conclusions: The 4D-mini-TEE probe delivers exceptional imaging capabilities for routine ex-aminations and transcatheter interventions without needing sedation. Its use reduces esophageal trauma and the need for general anesthesia, enhancing patient comfort and safety.

Three Seas Initiative (3SI) is still an underresearched area and is particularly important due to historical circumstances and economic backwardness. A study was carried out to assess the impact of renewable energy and production generated by the agricultural sector on CO2 emissions in 3SI countries between 2008 and 2020. The study used panel data analysis based on the two-step system generalised method of moments (GMM) and the Dumitrescu-Hurlin panel causality test. The results show that a 1% increase in the value-added generated by agriculture increases CO2 emissions in the countries studied by 0.11%. In contrast, a 1% increase in GDP leads to a 0.29% increase in CO2 emissions. Conversely, when renewable energy consumption increases by 1%, CO2 emissions fall by 0.25% in the countries studied. One way to reduce CO2 emissions from agricultural production in the short term is to increase the share of renewables, which, incidentally, is in line with EU action.

The three-dimensional morphology of frictional sub-surfaces holds significant importance for studying tribological issues. However, the uniformity of horizontal datum in 3D scanning is limited for curved surfaces, resulting in the inability to obtain accurate contour characterization parameters from the scanning results. This study aims to address this issue by constructing regular surface equations and normalizing the 3D profiler scanning results. By fitting the data, a "plane" surface representative of the surface features is obtained, and the paper demonstrates this approach on the surface morphology of different worn parts in the frictional area of spherical bearings located in the specific environment of the Three Gorges gate. The results indicate that the obtained "plane" effectively reconstructs the three-dimensional morphology map of the regular surface. Moreover, this reconstructed plane not only clearly illustrates the surface characteristics but also provides the foundation for analyzing the wear mechanism.

This study introduces a new procedure for three-component spectral matching of seismic ground acceleration records. The procedure involves preserving the phase angle and varying the Fourier amplitudes to match the spectra of the recorded records with a provided target spectrum that represents the spectral values of ground motions in three orthogonal directions. Several three-component recorded records were matched against two target response spectra to test the method. An accurate convergence was achieved in the velocity and displacement records. In addition, the scales among the components’ magnitude were maintained, creating realistic three-component ground motions. Such ground motion inputs are important to qualify critical structures sensitive to three-component motions. Our proposed procedure is novel because the present practices are mostly created based on one-component ground motions.

This paper introduces a multi-class hand gesture recognition model developed to identify a set of defined hand gesture sequences in two-dimensional RGB video recordings. The work presents an action detection classifier that looks at both appearance and spatiotemporal parameters of consecutive frames. The classifier utilizes a convolutional-based network combined with a long-short-term memory unit. To leverage the need for a large-scale dataset, the model uses an available dataset to then adopt a technique known as transfer learning to fine-tune the model on the hand gestures of relevance. Validation curves performed over a batch size of 64 indicate an accuracy of 93.95% (± 0.37) with a mean Jaccard index of 0.812 (± 0.105) for 22 participants. The presented model illustrates the possibility of training a model with a small set of data (113,410 fully labelled frames). The proposed pipeline embraces a small-sized architecture that could facilitate its adoption.

The paper proposes a novel methodology for the stabilization of shallow foundations, with a simplified model combined with 3D Electrical resistivity tomography (ERT-3D) and conso- lidation injections. To determine its usefulness, the method has been applied in a case located in Estepona (southern Spain). The chosen tomography model is the dipole-dipole configuration, with an optimized distance between electrodes of 0.80 m for a better visualization of the foundation subsoil; with this parameterization, a total of 72 electrodes were installed in the analyzed case. In this work, the depth of the anomaly in the building's supporting subsoil was detected ranging from 2.00 m to 3.90 m deep. The study also delineates areas of high resistivity variations (50-1,000 Ω m) in the middle and eastern end of the field. These data have been validated and corroborated with a field campaign. The results of the ERT-3D monitoring are presented, once the investment data has been processed with the RES3DINV software, from the beginning to the end of the stabilization intervention. The novelty occurs with the interaction between the tomography and the foundation consolidation injections, until the final stabilization; very useful methodology in case of emergency consolidation, where there is a need to minimize damage to the building. Thus, people using this combined system; will be able to practically solve the initial anomalies of the subsoil that caused the damages, in a non-invasive way, considerably lowering the value of the resistivities.

ARBTools is a Python library containing a Lekien-Marsden type tricubic spline method for interpolating three-dimensional scalar or vector fields presented as a set of discrete data points on a regular cuboid grid. ARBTools was developed for simulations of magnetic molecular traps, in which the magnitude, gradient and vector components of a magnetic field are required. Numerical integrators for solving particle trajectories are included, but the core interpolator can be used for any scalar or vector field. The only additional system requirements are NumPy.

Three-dimensional (3D) imaging has attracted more and more interests because of its widespread applications, especially in information and life science. These techniques can be broadly divided into two types: ray-based and wavefront-based 3D imaging. Issues such as imaging quality and system complexity of these techniques limit the applications significantly, and therefore many investigations have focused on 3D imaging from depth measurements. This paper presents an overview of 3D imaging from depth measurements, and provides a summary of the connection between these the ray-based and wavefront-based 3D imaging techniques.

Anthropogenic chemicals are fundamental to our standard of living in modern society. Unfortunately, some chemicals are persistent and can enter waste streams and ultimately the environment. Commonly used household products including pharmaceuticals and personal care products are an important source of contaminants. The aim of this study was to develop an “Up-the-pipe Solutions” framework to raise awareness about the presence and potential risks of chemicals found in household products to reduce their levels in waste streams or substitute them with less harmful alternatives. This approach based on The Natural Step framework and the concept of essentiality recognises the importance of engaging the community to raise awareness around the consequences of our daily activities and behavioural patterns that can lead to the release of persistent contaminants in main waste streams from the kitchen and bathroom and green wastes we generate.

Q345 steel is widely used in the construction industry, vehicle manufacturing industry, bridge construction industry and many other aspects due to its excellent comprehensive performance. However, due to its high silicon content, direct hot-dip galvanizing will lead to a series of problems, such as easy peeling of the coating due to the "silicon reactivity". In this paper, we adopt the "two-step hot-dipping method", first hot-dip aluminizing and then hot-dip galvanizing, to isolate the substrate and zinc liquid direct contact, so as to avoid the occurrence of "silicon reactivity". Through the microstructure characterization, neutral salt spray corrosion experiments, electrochemical experiments, the results show that: Al-Zn composite coatings from the inside out were perpendicular to the substrate growth of loose Fe2Al5 layer and Al-Zn layer, outbursts generation; Al-Zn composite coatings resistance to neutral salt spray corrosion was far more than the substrate; Al-Zn composite coatings polarization curve corrosion potential than the substrate was lower than that of the substrate by 0.512V, showing a strong corrosion resistance. It shows extremely strong corrosion resistance.

The introduction of stool as a readily obtainable sample and the recently developed simple-one-step (SOS) stool processing method offer an opportunity for TB diagnosis in children. We conducted this study at secondary health facilities in Ethiopia which are the first level referral facilities for childhood TB diagnosis and treatment with the aim to determine if stool-based TB diagnosis can be performed with reasonable level of concordance with sputum tests in using Xpert MTB/RIF Ultra. Eligible children 0-14 years with presumptive pulmonary TB were asked to provide stools in addition to routinely requested sputum samples. We computed Cohen’s kappa statistic in SPSS to determine the level of agreement between stool and sputum test results. Of the 373 children included in the study, 61% were &lt;5 years of age and 56% were male. Thirty-six children (9.7%) were diagnosed with TB and all started treatment. The rate of concordance between stool and sputum was high with kappa value of 0.83 (P&lt;0.001). There were more Xpert ultra positive test results on stool (n=27 (7.2%)) than on sputum/NGA (n=23 (6.2%)). Laboratories in secondary hospitals can perform stool-based TB diagnosis in children with high concordance between stool and sputum test results reaffirming the applicability of the SOS method.

The objective of this study was to evaluate the efficacy of one-step nucleic acid amplification (OSNA) for the detection of sentinel lymph node (SLN) metastasis compared to standard pathological ultrastaging in patients with early-stage endometrial cancer (EC). A total of 526 SLNs from 191 patients with EC were included in the study. 379 SLNs (147 patients) were evaluated by both methods, OSNA and standard pathological ultrastaging. The central 1-mm portion of each lymph node was subjected to semi-serial sectioning at 200-μm intervals and examined by hematoxylin-eosin and immunohistochemistry with CK19; the remaining tissue was analysed by OSNA for CK19 mRNA. The OSNA assay detected metastases in 19.7% of patients (14.9% micrometastasis and 4.8% macrometastasis), whereas pathological ultrastaging detected metastasis in 8.8% of patients (3.4% micrometastasis and 5.4% macrometastasis). Using the established cut-off value for detecting SLN metastasis by OSNA in EC (250 copies/μl), the sensitivity of the OSNA assay was 92%; specificity was 82%; diagnostic accuracy was 83%, and the negative predictive value was 99%. Discordant results between both methods were recorded in 20 patients (13.6%). OSNA resulted in an upstaging in 12 patients (8.2%). OSNA could aid in the identification of patients requiring adjuvant treatment at the time of diagnosis.

This paper presents a new high-efficiency-high-step-up based converter integrating two stype DC-DC Boost and Flyback coupled magnetic converter with recovery stage dedicated to smart HVDC distributed architecture in renewable energy production systems. Appropriate duty cycle ratio assumes that the recovery stage work with parallel charge and discharge to achieve high step-up voltage gain. Besides, the voltage stress on the main switch is reduced with a passive clamp circuit and thus, low on-state resistance Rdson of the main switch can be adopted to reduce conduction losses. The circuit is simple to control. As a final point of this research, the simulation and the prototype investigational results are presented to demonstrate the effectiveness of this proposed converter.

In this paper, the P versus NP problem is studied based on a six-dimensional space-time perspective. The gap between the P-class and NP-class arises from the relationship between time and the solution, as well as the answer that is independent of time. The complexity of solving a problem depends on the time dependence of the answer. Solving problems whose answers do not depend on the passage of time is very difficult and impossible. Like the description of the gravitational factor in Newtonian physics, NP class problems require different mathematical tools. Based on the generalization of physical facts in mathematics, based on six-dimensional space-time, a method to solve problem P versus NP problem has been stated. The results of this study offer a fresh insight into information processing that occurs independent of the passage of time.

Void fillers are required for osseous gaps generated after orthopedic procedures as medial open-wedge high-tibial osteotomy (MOWHTO) to provide sufficient structural support and a rapid osteosynthesis. We developed a novel three-dimensional (3D) printing-based platform technology using the customized 3D scaffolds covered with polycaprolactone (PCL)/β-tri-calcium phosphates (β-TCP)/bone decellularized extracellular matrix (dECM) for use as bone substitute scaffold, which can be effectively exploited to estimate the calculated correction angle with preoperative simulations. PCL/β-TCP/bone dECM scaffolds demonstrated significantly higher cell contain levels in cell seeding efficiency, excellent proliferation capacity, and promotion of early osteogenic differentiation compared with PCL/β-TCP scaffolds. The scaffolds promoted bone mineralization at the early time points of an in vivo study (8 weeks) and exhibited biodegradable properties (38% for 16 weeks). The correction angle measured after osteotomy using 3D printed scaffolds was estimated with high accuracy with low errors (10.3° ± 0.9°), was and was not significantly different even in the presence of lateral cortical hinge fractures. The customized 3D scaffold enriched with PCL/β-TCP/bone dECM yielded excellent cell seeding efficiency, proliferation capacity, early osteogenic differentiation, and bone mineralization outcomes. It is expected to solve the disadvantages related with bone union in MOWHTO, and to replace autografts in the future.

Applied talent is not only a builder of human civilization but also a promoter of economic development. They not only need systematic and solid engineering theoretical knowledge but also rich engineering practical experience. Applied undergraduate colleges are the cradle for cultivating applied talent and shoulder the important mission of cultivating various types of applied talent for society. With the rapid development of higher education, the number of applied undergraduate institutions has sharply increased, but the quality of applied talent cultivated by them has shown a significant decline, which greatly restricts the pace of industrial development in the world. This article proposes a new concept of promoting the "three certificates" (graduation certificate, degree certificate, and skill certificate) education model in applied undergraduate colleges, which is of great significance for the country to cultivate composite talents with the ability of "product design, production management, and product processing" at the same time.

A power factor correction (PFC) rectifier is compulsory for any electronic circuitry connected to the electrical grid. The majority of PFCs that are utilized are based on a step-up converter that supplies high DC voltage at its output terminal. Electric vehicle battery voltage varies from a few hundred to almost a thousand volts. Thus, an additional conversion step is obligatory when designing an all-brand universal charger. This paper presents a new type of front-end versatile step up / down three voltage level PFC. The rectifier can operate in continuous conduction mode or discontinuous conduction mode. First, the rectifier’s principle of operation is described, and then an innovative rectifier is analyzed for continuous and discontinuous conduction modes. Finally, the proposed theory is experimentally validated in a multiplier-less dual loop mode at discontinuous conduction modes. It was shown that although there is no multiplier use in the control circuitry, the power factor is near unity. It was revealed that the rectifier could swing the output voltage from 50 V to 900 V while the input voltage was 230 Vrms. The innovative topology suits any standard PFC rectifier, three-level voltage supplement, and dual-stage low-voltage power supply.

Pedestrian Dead Reckoning (PDR) is a promising algorithm for indoor positioning. However, the accuracy of PDR degrades due to the accumulated error, especially in multi-floor buildings. This paper introduces a three-dimensional (3D) positioning method based on terrain feature matching to reduce the influence of accumulated error in multi-floor scene. The proposed method involves two steps: motion pattern recognition and position matching calibration. The motion pattern recognition aims to detect different motion states, i.e., taking the stairs or horizontal walking, from the streaming data. Then, stair entrances and corridor corners are matched with transition points of motion states and pedestrian turning points, respectively. After matching, calibration is performed to eliminate the accumulated errors. By carrying out experiments on a two-floor closed-loop path with a walking distance about 145 m, it is shown that this method can effectively reduce the accumulated error of PDR , achieving accurate 3D positioning . The average error is reduced from 6.60 m to 1.83 m.

Mechanical properties of three-dimensional (3D) printed resin can be improved by decreasing oxygen concentrations during post-curing, and nitrogen saturated post-curing has been applied for the purpose. This study aimed to evaluate and compare the color stability of 3D printed resin crowns post-cured in normal air and nitrogen saturated conditions. Crowns were fabricated with 3D printer and post-cured in normal air (control group; air) or nitrogen saturated condition (experimental group; nitrogen). The specimens in each group were subdivided into four subgroups, each exposed to different discoloration agents: distilled water, coffee, wine, and curry. Post-immersion color changes were measured using a digital spectrophotometer and analyzed through repeated measures ANOVA. Fourier Transform Infrared (FT-IR) spectroscopy evaluated the degree of conversion of resin over immersion times for both post-curing conditions. Comparing the effects of post-curing conditions, significant difference was found between control and experimental groups over immersion time in wine and curry subgroups. In FT-IR analysis, there was significant difference in degree of conversion between the air and nitrogen groups from 10 to 300 seconds. The findings suggest that nitrogen saturated post-curing can potentially enhances the conversion rate of 3D printed resin crowns, thereby improving their color stability.

This paper proposes a new cascaded three-phase multilevel inverter based on a cascaded submultilevel and single-phase H-bridge structure. The voltage source of the traditional single-phase H-bridge is replaced with the proposed cascaded submultilevel. Cascading two basic units forms the submultilevel unit. The basic and submultilevel units generate positive voltage only hence the need for an H-bridge to generate both polarities of load voltage. Five algorithms of source voltage are proposed and the optimal algorithm selected to generate the peak load voltage and output levels. The proposed three-phase cascaded multilevel inverter generates 31-level of load voltage. The per-phase component distribution of the proffered inverter are twelve power switches, four dc sources and twelve driver circuits accordingly. Principal merits of the proposed 31-level inverter are high quality load waveforms, production of high levels of load voltage utilizing reduced component quantity, simple cascaded layout, decreased inverter area, minimal inverter cost, minimum inverter losses and utilizing lower rated switches. Also, the proposed topology is highly suited for employment in PV-DVR and other power systems. To validate these advantages of the proposed multilevel inverter, contrastive analysis of the proposed inverter and existing topologies are studied. Finally, the functionality of the proposed inverter is substantiated by simulation in PSCAD/ EMTDC software.

Prenatal diagnosis of clubfoot traditionally relied on two-dimensional ultrasonography. To enhance diagnosis and predict postnatal outcomes, we examined the parameters that differentiate pathological clubfoot using three-dimensional ultrasonography. In our retrospective study, we examined the findings of prenatal ultrasound and the postnatal outcomes of pregnancies with suspected congenital clubfoot between 2018 and 2021. Based on the three-dimensional perspective, we measured the angles of varus, equinus, calcaneopedal block and forefoot adduction and compared the sonographic variables between the postnatal treated and non-treated groups. We evaluated 31 pregnancies (47 feet) with suspected clubfoot using three-dimensional ultrasonography. After delivery, a total of 37 feet (78.7%) underwent treatment involving serial casting only or additional Achilles tenotomy. The treated group showed significantly greater hindfoot varus deviation (60.5° vs. 46.6°, p=0.026) and calcaneopedal block deviation (65.6° vs. 26.6°, p &lt;0.05) compared to the non-treated group. The calcaneopedal block had an area under the curve of 0.98 with a diagnostic threshold of 46.2 degrees (sensitivity of 97%, specificity of 90%, positive predictive value of 97%, and negative predictive value of 90%). During prenatal evaluation of clubfoot using three-dimensional ultrasonography, the calcaneopedal block deviation has the potential to predict postnatal treatment.

This study investigates the nonlinearities in three-phase inverters for SiC-based systems and compares their performance to IGBT-based systems. An analytical model of inverter voltage distortion is developed, which accounts not only for dead time (td), switching delay time, switching frequency (fs), and voltage drops of power devices, but also for output parasitic capacitance (Cout). Experimental tests validate the model, which provides a more accurate estimate of the inverter’s output phase voltage distortion. The power device characteristics are obtained from datasheets, while Cout is determined through experimentation. Three-phase inverters with varying switching frequencies, fundamental frequencies, and dead-time values are used in simulations and experiments to determine the influence of nonlinearity on phase voltage deviation and current distortion. The results show that, due to SiC devices’ faster switching time, the phase voltage deviation and phase current distortion are lower in SiC-based inverters than in IGBT-based ones for high-frequency applications, as the dead time can be reduced.

Taking Shanxi Province, a typical energy region in China, as the research object, data on economic development quality and environmental pollution intensity from 2001 to 2021 were selected. Linear regression, numerical simulation, and Pearson correlation coefficient were used to analyze the evolution characteristics of economic development quality and environmental pollution intensity in Shanxi Province in the past 20 years, and to explore the relationship between economic development and environmental pollution. The results indicate that since 2001, Shanxi Province has made long-term progress in economic development, with GDP increasing by nearly 10 times and an average annual growth rate of around 7%. In the past 20 years, the main pollutants have shown a trend of increasing first and then decreasing steadily, with a turning point occurring during the "12th Five Year Plan" period. This shows that the environmental policies and investments of the Chinese and Shanxi provincial governments in the past 10 years have been effective in the new era. The numerical simulation curve results show that the per capita GDP exhibits a classic inverted "U" curve relationship with wastewater and SO2 emissions, with a turning point occurring at around 20000 yuan per capita GDP; However, there is a monotonic decreasing trend with Chemical oxygen demand and ammonia nitrogen emissions, and a monotonic increasing trend with solid waste generation. There is no turning point yet. The correlation analysis results further support the fitting curve conclusion.

The purpose of this paper is to study the influence of diffusion and thermal loading due to pulsed laser heating on a thermoelastic solid with voids in the context of the model of three-phase-lag. The non-dimensional governing equations are formulated and then the exact expressions for the temperature field, the displacement components, the stress components, the concentration field and the change in the volume fraction field are obtained using the normal mode technique. The material is an isotropic, homogeneous elastic half-space and heated by a non-Gaussian laser beam with pulse duration of ps. The magnesium crystal element is used as an application to compare the predictions induced by diffusion and laser pulse on poro-thermoelastic medium of the model of three-phase-lag with those for the theory of Green–Naghdi of type III. The results obtained for thermal changes are verified by comparison with two theories of thermoelasticity, namely the model of three-phase lag (3PHL) and the Green and Nagdi type III theory. Plot the expressions to examine the effect of the laser pulse at two different values of time and the effect void parameter. This study also yields some interesting special cases.

The poor success rate of preclinical drugs which target the nervous system is related to the highly complex nature of brain physiology and pathophysiology. For in vitro drug screening in this field, the two-dimensional (2D) approach - where cells are incubated in a monolayer - is not physiologically relevant. In contrast, in vivo rodent models are very low throughput and expensive. As such, improved, well-characterised three dimensional (3D) in vitro models should be employed to bridge the gap between 2D in vitro primary screening and rodent models by incorporating aspects of the in vivo brain environment. These key features include the extracellular matrix (ECM) and a multidimensional relationship of supporting cells. In this study, a neural progenitor cell line was differentiated into the main types of cells found in brain, including neurons and astrocytes. This model was designed in a 3D extracellular matrix replacement in a minimalised manner. Different culture formats using multi-well plates were explored and a high-throughput cellular imaging platform was applied. Next, we applied this model to assess neural toxicity of a newly synthesised dual-specificity tyrosine-regulated kinase 1 (DYRK1) inhibitor derived from natural compounds, which is structurally related to a natural DYRK1A inhibitor harmine, K04179. Chemical studies have already shown that K04179 has higher specificity to DYRK1A compared with previously reported DYRK1 inhibitors, such as INDY. We have produced the first report of the biological effects of this new compound on the new 3D minimalised mid-brain model with quantification of both neuronal and astrocyte populations in tandem, revealing differential toxic effects of DYRK1 inhibitor compounds K04179 and INDY on neurons and glia.

This paper proposes a contact force controller for a constrained flexible manipulator in three-dimensional motion. This controller used the conversion formula obtained empirically and experimental results showed the effectiveness of the proposed contact force controller. First, the manipulator was operated with the tip of the second link restrained, then, time response of the root strain, joint angles and contact force were used to derive the relational between the three quantities. The effectiveness of the relational expression was verified by conducting a target contact force tracking experiment by inputting the angle from the relational expression. The contact force control using the strain feedback method was proposed with the strain amount estimated from the target contact force as the target value, and its effectiveness was verified by experiments. From the results obtained, controller using the strain feedback method was designed for the purpose of controlling the contact force at the tip of a flexible manipulator with two links and three degrees of freedom that performs three-dimensional spatial motion, and its effectiveness was shown by comparison with the contact force feedback method.

Three body systems in which one of the bodies is ejected without escaping the binary system have previously been studied in various restricted forms. However, none of these studies dwells on the problem in a general setting. Thus, to study this phenomenon qualitatively, we try to expand this problem's scope to unequal mass systems and generalize them by considering various configurations of fixed initial points with precisely calculated initial velocities, some zero velocity models and some optimized models. We will see the use of terminology similar to the previous studies done in this domain but incorporate different analytical and evaluation methods.

We present simple relations for nuclear stability and nuclear binding energy with respect to three gravitational constants associated with electroweak, strong and electromagnetic interactions.

In the Korean construction industry, legal and institutional safety management improvements are continually being pursued. However, there was a 4.5% increase in the number of workers’ deaths at construction sites in 2017 compared to the previous year. Failure to wear safety helmets seems to be one of the major causes of the increase in accidents, and so it is necessary to develop technology to monitor whether or not safety helmets are being used. However, the approaches employed in existing technical studies on this issue have mainly involved the use of chinstrap sensors and have been limited to the problem of whether or not safety helmets are being worn. Meanwhile, improper wearing, such as when the chinstrap and harness fixing of the safety helmet are not properly tightened, has not been monitored. To remedy this shortcoming, a sensing safety helmet with a three-axis accelerometer sensor attached was developed in this study. Experiments were performed in which the sensing data were classified whether the safety helmet was being worn properly, not worn, or worn improperly during construction workers’ activities. The results verified that it is possible to differentiate among wearing status of the proposed safety helmet with a high accuracy of 97.0%

Cold gas-dynamic spray (cold spray) is an evolving coating deposition and restoration technology in which particles are deposited above the sonic speed. This paper presents the non-destructive three-dimensional characterization of cold sprayed stainless steel coating. The visualization of coating morphology and volumetric porosity, and the analyses of porosity size and spatial distributions confirmed that dense stainless steel coating with non-connected, micron-sized gradient porosity is successfully produced by cold spray. The suitability of X-ray tomography for characterizing cold sprayed coatings is assessed.

Object. Utilization of pedicle screws (PS) for spine stabilization is common in spinal surgery. With reliance on visual inspection of anatomical landmarks prior to screw placement, the free-hand technique requires a high level of surgeon skill and precision. Three-dimensional (3D) computer-assisted virtual neuronavigation improves the precision of PS placement and minimize steps. Methods. Twenty-three patients with degenerative, traumatic, or neoplastic pathologies received treatment via a novel three-step PS technique that utilizes a navigated power driver in combination with virtual screw technology. 1) Following visualization of neuroanatomy using intraoperative CT, a navigated 3-mm match stick drill bit was inserted at anatomical entry point with screen projection showing virtual screw. 2) Navigated Stryker Cordless Driver with appropriate tap was used to access vertebral body through pedicle with screen projection again showing virtual screw. 3) Navigated Stryker Cordless Driver with actual screw was used with screen projection showing the same virtual screw. One hundred and forty-four consecutive screws were inserted using this three-step, navigated driver, virtual screw technique. Results. Only 1 screw needed intraoperative revision after insertion using the three-step, navigated driver, virtual PS technique. This amounts to a 0.69% revision rate. One hundred percent of patients had intraoperative CT reconstructed images to confirm hardware placement. Conclusions. Pedicle screw placement utilizing the Stryker-Ziehm neuronavigation virtual screw technology with a three step, navigated power drill technique is safe and effective.

With large-scale distributed generators (DGs) in an active distribution network (ADN), conventional load flow convergence failure is incurred by heavy power transmission. The Holomorphic Embedding Load Flow Method (HELM) has proven to be more robust than the Newton–Raphson method under heavy power transmission. At present, HELM is mainly designed for balanced transmission networks. In this study, we developed a three-phase HELM model to accommodate DGs, delta connection loads, and ZIP loads for ADN. The effectiveness and better performance of the proposed method under heavy load situations were validated using modified unbalanced IEEE 13, 34, 37, and 123 test feeders.

Effect of abrasive shape on the three-body abrasion behaviors of monocrystalline silicon was investigated by Molecular dynamics modelling. The axial ratio of abrasive particle was varied from 1.00, i.e., a complete sphere, to 0.40 to mimic abrasive shape. The particle’s movement turns toward sliding from rolling when the axial ratio becomes less than a critical value 0.46. In the abrasion process, the friction force and normal force showed an approximately sinusoid-like fluctuation for the rolling ellipsoidal particles, while the front cutting of particle caused that friction force increased and became larger than normal force for sliding particles. The phase transformation process was tracked under different particle’ movement patterns. The Si-II and Bct5 phase producing in loading process can partially transform to Si-III/Si-XII phase and backtrack to original crystal silicon under pressure release, which also occurred in the abrasion process. The secondary phase transformation showed difference for particles’ rolling and sliding movements after three-body abrasion. The rolling of particle induced the periodical and inhomogeneous deformation of substrates, while the sliding benefited producing high-quality surface in CMP process. This study aiming to construct more precise model to understand the wear mechanism benefits evaluating the MEMS wear and CMP process of crystal materials.

Cryopreservation, storing biological material in liquid nitrogen (LN, −196 °C), offers a valuable option for the long-term conservation of non-orthodox seeds and vegetatively propagated species in the sector of agrobiodiversity and wild flora. Although large-scale cryobanking of germplasm collections has been increasing worldwide, the wide application of cryopreservation protocol in wild flora is hampered by difficulties in vitro propagation and a lack of universal cryopreservation protocols, among others. This study established a systematic approach to developing an in vitro culture and droplet-vitrification cryopreservation procedure for shoot tips of Scrophularia kakudensis. The standard procedure includes two-step preculture with 10% sucrose for 31 h and with 17.5% sucrose for 16 h, osmoprotection with loading solution C4-35% (17.5% glycerol + 17.5% sucrose, w/v) for 30 min, cryoprotection with A3-80% (33.3% glycerol + 13.3% dimethyl sulfoxide + 13.3% ethylene glycol + 20.1% sucrose, w/v) at 0 °C for 60 min, and cooling and rewarming using aluminum foil strips. After unloading, a three-step regrowth procedure starting with an ammonium-free medium with growth regulators was essential for developing normal plantlets from cryopreserved shoot tips. Liquid overlay on the gelled medium two weeks after inoculation resulted in vigorous growth during subcultures. Moreover, liquid overlay increased LN regeneration by up to 80%, i.e., 23% higher than no liquid overlay.

The aim of this paper is to apply all the existing pyranometric method, to estimate the sunshine duration from the global solar irradiation, in order to find in their original form the most suitable method for a tropical site. Then, in a second step, one of these methods will be optimized to well fit tropical sites. Five methods in the literature (Step Algorithm, Carpentras Algorithm, Slob &amp; Monna Algorithm, Slob &amp; Monna 2 Algorithm, and Linear Algorithm) were applied with eleven years of global and diffuse solar radiation data. As a result, in their original form, the Step Algorithm is on the first rank. But in the second step, after improving its main coefficients, the Carpentras Algorithm was found to be the best algorithm for tropical site in the southern hemisphere.

Abstract: Background and objectives: Symptomatic walled-off pancreatic necrosis is a serious local complication of acute necrotising pancreatitis. The endoscopic step-up approach is the standard treatment for symptomatic walled-off pancreatic necrosis; however, adjunctive radiologic percu-taneous drainage for this condition is controversial. This study compared the clinical and radio-logic resolution of walled-off pancreatic necrosis achieved with the endoscopic step-up approach with or without radiology-guided percutaneous drainage. Material and Methods: This retrospective, single-center cohort study enrolled patients with symp-tomatic walled-off pancreatic necrosis who underwent endoscopic transmural drainage (ETD) followed by directed endoscopic necrosectomy (DEN) with or without radiology-guided drainage. A total of 34 patients (endoscopic approach, n=22; combined modality approach, n=12) underwent the endoscopic step-up approach (ETD followed by DEN). Baseline characteristics, clinical success, and resolution of necrosis were compared between groups. Results: All patients achieved symptom resolution from walled-off pancreatic necrosis. The mean patient age was 58.4 years, and 21 (61.8%) were men. After treatment with the endoscopic approach and combined modality approach, clinical success was achieved in 90.9% of patients within 11.5 days, and 66.7% of patients within 16.5 days, respectively. Both the total hospital stay (55 days vs 71 days; p=0.071) and time to complete radiologic resolution were shorter (93 days vs 124 days; p=0.23) in the endoscopic approach group. Conclusion: The endoscopic step-up approach resulted in the clinical resolution of symptomatic walled-off pancreatic necrosis comparable to that of the combined modality drainage. However, the endoscopic approach alone allows higher clinical success, early clinical and radiologic resolution, and a shorter hospital stay.

Classical enzyme kinetics are summarized and linked with modern discoveries here. The time course of sequential catalytic events by biological macromolecular enzyme is analyzed at the molecular level; the relationships between catalytic efficiency (turnover number), catalytic rate/velocity, the amount of time taken and physical/biochemical conditions of the system are discussed. This writing tries to connect the microscopic molecular behavior of enzyme to kinetic data obtained in experiment, and the hypothesis proposed here provide an interpretation to previous experimental observations and can be testified by future experiments.

Arrhythmic sudden cardiac death (SCD) has an annual prevalence of 1 per 1000 while 75% of the victims suffer from ischemic and 10% from non-ischemic or hypertrophic cardiomyopathy. Altogether, these three entities account for more than 80% of the total SCD victims. Guidelines for implantable cardiac defibrillators are still dominated by LVEF<30% from the MADIT II study. In terms of arrhythmic risk stratification, the PRESERVE-EF study restored in clinical practice the two-step arrhythmic risk stratification approach based on Electrocardiographic non-invasive risk factors (NIRFs) guiding to electrophysiological study. In our times with the multiple cardiac imaging methods and artificial intelligence applications availability, this two-step approach based on integrated arrhythmia mechanisms detection, emerges as an efficient SCD risk stratification paradigm for these three entities but also for the patients with congenital heart disease.

Liquid crystal elastomers (LCEs) are shape morphing materials whose large and reversible shape transformation results from the coupling between the mobile anisotropic properties of liquid crystal (LC) units and the rubber elastic of polymer networks. Their shape changing behaviors under the stimuli are largely directed by LC orientations, and therefore various strategies have been developed to spatially modulate the LC alignments. But most of the methods suffer from complex fabrication technologies or intrinsic limitations in applicability. To address this issue, programmable complex shape changes in some types of LCEs, such as polysiloxane side-chain LCEs or thiol-acrylate main-chain LCEs, etc, have been achieved by using a mechanical alignment programming process coupled with two-step crosslinking. Here, we report a polysiloxane main-chain LCE with programmable 2D and 3D shape changing performances achieved by mechanically programming the polydomain LCE between the two crosslinking steps. The resulting LCEs exhibited reversible thermal induced shape transformation between the initial and programmed shapes due to the two-way memory between the first network structure and the second network structure. Our work would be potential for expanding the applications of LCE materials in actuators, soft robotics and smart structures where arbitrary and easily programmed shape morphings are needed.

In the context of high frequency and intensity forest fires driven by future warming and drying climate, early detection and effective control of fires are extremely important to reduce losses. Satellite remote sensing, characterized by its broad observational scope and strong repeat observation capability, has become an important method for rapid monitoring of forest fires, replacing traditional means such as manual measurement and aerial photography. This paper addresses the misjudgments caused by solely relying on changes in infrared band brightness values and single-band separation in forest fire discrimination. It constructs the angle slope index ANIR based on the red band, near-infrared band and short-wave infrared band, Angle slope index AMIR based on the short-wave infrared band, mid-infrared band and far-infrared band, and angle slope index AMNIR based on the difference between the AMIR and ANIR, integrating the strong inter-band correlations and the reflectance characteristics of visible and short-wave infrared bands to simultaneously monitor smoke and fuel biomass changes in forest fires. To address the omissions caused by single-image fire discrimination algorithms, the paper constructs time-series Angle slope difference indices ∆ANIR and ∆AMIR. To address the different fire point discrimination thresholds caused by background difference in different time and space, the paper uses the decomposed three-dimensional OTSU(Maximum inter-class variance method) algorithm to calculate the segmentation threshold of the sub-regions constructed from the AMNIR data. The methods were validated using high temporal resolution meteorological satellite Himawari-8 and ground truth fire data from Hunan Province, China, from 2018-2019. The results show that the discrimination method based on the ASITR(Angle slope indices thresholds) method exhibits an accuracy of 0.88, a missed detection rate of 0.17, and an overall evaluation value of 0.85, which is 0.09 higher in accuracy and 0.03 higher in overall evaluation than the discrimination method based on infrared bands brightness values proposed by Feng et al. [1] (accuracy 0.79, missed detection rate 0.14, overall evaluation value 0.82); the method based on the FAMN_OTSU_ASITR (Fusion of Angle slope difference index (false) data, Decomposed three-dimensional OTSU adaptive threshold segmentation Algorithm and ASITR) exhibits an accuracy of 0.85, a missed detection rate of 0.08, and an overall evaluation value of 0.88, which is 0.09 lower in missed detection rate and 0.03 higher in overall evaluation as compared to the ASITR. The results demonstrate that the forest fire discrimination method based on Angle slope indices, Himawari-8 satellite data, and the decomposed OTSU adaptive threshold segmentation algorithm can improve the accuracy of forest fire discrimination and reduce errors in missed detections.

Global dust events have become more frequent due to climate change and increased human activity, significantly impacting air quality and human health. Previous studies have often focused on simulating cross-regional dust transport based on atmospheric parameters; however, comprehensive monitoring of dust events remains challenging. Therefore, this study utilized Fengyun-4A (FY-4A) satellite Advanced Geostationary Radiation Imager (AGRI) imagery, Cloud-Aerosol Lidar and Infrared Pathfinder Satellite Observation (CALIPSO) lidar, and other auxiliary data to conduct three-dimensional spatiotemporal monitoring and cross-regional transport analysis of two typical dust events in the Beijing–Tianjin–Hebei (BTH) region of China using four dust intensity indices (Icsd, Dust Detection Index (DDI), Dust value (DV), and Dust Strength Index (DSI)) and the HYSPLIT model. We found that among the four indices, DDI was the most suitable for studying dust in the BTH region, with a detection accuracy (POCD) of > 88% at all times and reaching a maximum of 96.14%. Both the 2021 and 2023 dust events originated from large-scale deforestation in southern Mongolia and the border area of Inner Mongolia, with dust plumes distributed between 2 and 12 km being transported across regions to the BTH area. Further, when dust aerosols are primarily concentrated below 4 km and PM10 concentrations consistently exceed 600 µg/m³, large dust storms are more likely to occur in the BTH region. The findings of this study provide valuable insights into the sources, transport pathways, and environmental impacts of dust aerosols.

As a new plant slope protection technology, living stumps can effectively improve slope stability. The current study attemptes to investigate the mechanical characteristics of the root system of living stumps and their reinforcement mechanism on slopes by carrying out a three-dimensional living stump slope modeling test. Using ABS materials, a 3D model of a living elm stump was created by 3D printing and a slope model test was carried out. The reinforcement mechanism of the living stump was studied through a combination of model testing and numerical simulation. The results indicate that, due to the presence of living stumps in the lower and middle parts of the slope, the maximum shear stress area of the soil moved to a deeper direction. The stress state of the soil around the living stump was effectively improved due to the existence of the lateral root system.Living stumps in the lower part of the slope cross the potential sliding surface and transferred the soil shear stress gradually to the root system through root-soil interaction. Moreover, the tap roots and lateral roots of living stumps form a robust spatial structure that bears the shear stress of soil together, thus increasing the stability of the slope.

To solve the problem of a uneven load for a dual-input counter-rotating transmission system, this research is based on Small Displacement Torsor Jacobian-Torsor theory.Considering the influence of the local parallel chain of a gearbox on the calculation accuracy of the backlash,the processing method of a meshing tooth pair parallel chain is proposed. The probability distribution of the tolerance band of gearbox manufacturing and assembly errors is modeled, the three-dimensional tolerance analysis model of a dual-input counter-rotating gearbox is established, and the Monte Carlo method is used to solve the backlash of the output end. The output backlash is solved with the Monte Carlo method, and the theoretical design backlash is combined with the output backlash to derive the gearbox side clearance range. The gearbox shaft system is analyzed statically, the range of the equal load coefficient is calculated, and the equal load performance optimization method based on the matching relationship between the gear backlash and the elastic shaft torsional stiffness is proposed. The correctness of the three-dimensional tolerance analysis combined with the elastic deflection angle used to optimize the equal load performance of the dual-input counter-rotating transmission system is verified by comparison with the relevant test data.

In this paper we study a special kind of finite mixture model. The sample drawn from the model consisits of three parts. The first two parts are drawn from specified distributions f1 and f2, while the third one is drawn from the mixture. A problem of interest is whether the two distributions f1 and f2 are the same. To test this hypothesis, we first define the regular location and scale family of distributions and assume that f1 and f2 are regular denisty functions. Then the hypothesis transforms to the equalities of the location and scale parameters, respectively. To utilize the information in the sample, we use Bayes’ theorem to obtain the posterior distribution and give the sampling method. Then we propose the posterior p-value to test the hypothesis. The simulation studies show that our posterior p-value largely improves the power in both normal and logistic cases while nicely controls the Type-I error. A real halibut dataset is used to illustrate the validity of our method.