Acid fracturing simulation is used widely to optimize carbonate reservoirs and improve acid fracturing treatment performance. In this study, a method was used to minimize the risk of the acid fracturing treatment. First, optimal fracture geometry parameters with UFD methods are calculated. After that, design components change as long as fracture geometry parameters reach their optimal values. The results showed a high flow rate needed to achieve optimal fracture geometry parameters with increasing acid volume. Sensitivity analysis was performed on controllable and reservoir parameters. It observed that a high flow rate should be applied for a low fluid viscosity to achieve the optimization goals. Straight acid reaches optimal conditions at a high flow rate and low volume. These conditions for retarded acids appear only at a low flow rate and high volume. The study of the acid concentration for gelled acid showed that as it increased, the flow rate and volume increased. Besides, for low permeability formation, a large fracture half-length and small fracture width are desirable. In this case, a higher flow rate will be required. The sensitivity analysis showed that the optimum flow rate and acid volume increase and decrease for the high Young's modulus. The effect of closure stress was also investigated and observed for a sample with high closure stress, low flow rate, and high acid volume are required.

The screening and treatment of acid mine drainage (AMD) using Na₂FeO₄ has been explored. Elemental composition was performed using an ICP-OES for the raw and treated AMD. The AMD samples were collected from three different sampling sites (RTW1, RTW2 and RTW3) in Pretoria, South Africa with acidic pH ranging between 2.50 and 3.13. Total dissolved solids and Electrical Conductivity of AMD samples ranged between 960 and > 1000 mg. L^-1, 226 and 263 µS. cm^-1, respectively. The final pH of treated water samples increased up to ≥ 9.5 after treatment with Na₂FeO₄. Sodium ferrate showed dual functions by removing metals and raising the pH of the treated water. Concentrations of most trace elements were not complying with WHO and DWAF guideline standards in raw AMD while after treatment with Na₂FeO₄ the concentrations were below guidelines for domestic and irrigation purposes.

Myxobacteria represent a viable source of chemically diverse and biologically active secondary metabolites. The myxochelins are a well-studied family of catecholate-type siderophores produced by various myxobacterial strains. Here, we report the discovery, isolation and structure elucidation of three new myxochelins N1–N3 from the terrestrial myxobacterium Corallococcus sp. MCy9049, featuring an unusual nicotinic acid moiety. Precursor-directed biosynthesis (PDB) experiments and total synthesis were performed in order to confirm structures, improve access to pure compounds for bioactivity testing and to devise a biosynthesis proposal. The combined evaluation of metabolome and genome data covering myxobacteria supports the notion that the new myxochelin congeners reported here are in fact frequent side products of the known myxochelin A biosynthetic pathway in myxobacteria.

The separation of rare earth metals (REM) from a neodymium magnet has been widely studied in the last year. We have shown that the waste of computer hard disk contains 25.41 % neodymium, 64.09 % iron, and <<1 % boron. To further isolate rare-earth metals, the magnet was acidically dissolved in open and closed systems. In both methods of dissolution was used concentrated nitric acid. The difference between these methods are the conditions of dissolution of magnet. The magnet was dissolved in a microwave sample preparation system at different temperatures and pressures in a closed system. In the open system, the acid dissolution of the magnet conducted at room temperature. 0.2 g of the neodymium magnet sample was taken under two conditions, and the dissolution process in the closed system lasted 1 hour, and in the open system-30-40 minutes. The open system is a non-laborious, simple and cheap method of dissolving the magnet by comparing both systems. Therefore, an open sample preparation system is used for further work. To remove the iron in the magnet, oxalic acid was used and precipitated as oxalates under both conditions. According to the result of the ICP-MS method, it is shown that the neodymium and iron contents in the precipitate are 24.66 % and 0.06 %, respectively. This shows that the iron has almost completely passed to the filtrate. Thus, it is possible to remove the iron from the sample.

BioPBS is gaining attention in the biodegradable polymer market due to their promising properties such as high biodegradability and processing versatility representing a potential sustainable replacement for fossil oil-based commodities. However, there is still a need to enhance its properties for certain applications, being aesthetical and mechanical properties a challenge. The aim of the present work is to improve these properties by adding selected additives that will confer bioPBS with comparable properties to that of current counterparts such as polypropylene (PP) for specific applications in the automotive and household appliances sectors. A total of thirteen materials have been studied and compared, being twelve biocomposites containing combinations of three different additives: a commercial red colourant, itaconic acid (IA) to enhance colour fixation and zirconia (ZrO2) nanoparticles to maintain at least native PBS mechanical properties. Results show that the combination of IA and the colouring agent tends to slightly yellowish the blend due to the absorbance spectra of IA and also to modify the gloss due to the formation of IA nanocrystals that affects light scattering. In addition, for low amounts of IA (4wt.%), young modulus seems to be kept while elongation at break is even raised. Unexpectedly, a strong aging affect was found after 4 weeks. IA increases the hydrophilic behaviour of the samples and thus seems to accelerate the hydrolisation of the matrix, which is accompanied by an accused disaggregation of phases and an overall softening and rigidization effect. The addition of low amounts of ZrO2 (2wt.%) seems to provide the desired effect for hardening the surface while almost not affecting the other properties; however, higher amounts tends to form aggregates saturating the compounds. As a conclusion, IA might be a good candidate for colour fixing in biobased polymers.

The direct Cr (VI) reduction process by oxalic acid was conducted and the results showed that the Cr (VI) was efficiently reduced by oxalic acid at high reaction temperature and high dosage of oxalic acid. The reduced product, Cr (III), was easily generated stable complex compounds (Cr(HC2O4)3) with oxalate, which displayed a negative effect on the reduction process. The high reaction temperature and high acidic medium could destroy the stable structure of a complex compound to release oxalate, and facilitate the reduction of Cr (VI). Generally, the present study provided a versatile strategy for Cr (VI) reduction, exhibiting a bright application future for real wastewater treatment.

This work shows the results obtained in the synthesis of srilankite nanoparticles, (Zr, Ti)O2, and TiO2 anatase, both catalysts presented an admix of phases, anatase/rutile, and srilankite/rutile, respectively. Their performance in the production of biodiesel through the esterification of oleic acid was evaluated. The catalysts were obtained using the sol-gel process and sulfated via the impregnation method. The samples were characterized using X-ray diffraction (XRD), scan electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS) and Fourier-Transform Infrared Spectroscopy (FTIR) to analyze the properties in its crystalline structure, morphology, and chemical composition. Its efficiency during the esterification reaction was measured based on the decrease in free fatty acids (FFA). FFA, oleic acid was added at different weight percentages (1%, 3%, and 5% w/w). The time of reaction was 6 hours at 55 °C and the catalyst with better performance was the sulfated Srilankite/rutile, reaching a maximum conversion of up to 90%.

Bauxite residue (BR) is a well promising resource for critical metals and especially scandium (Sc), a rare and expensive metal with increasing applications in advanced technology. Particularly, Greek BR’s composition indicates a sound possibility for a commercially viable recovery of Sc under the conditions of an optimized leaching process and the subsequent use of advanced separation techniques. Leaching with mineral acids emerges as the dominant selection with comparison to other techniques. This study investigates an optimized leaching condition set on Sc recovery, using sulfuric acid as the most suitable among different acids tested, in the context of process economics and environmental constraints. Several variables were studied individually or combined in order to achieve high Sc concentration in the leachate as well as to ensure selectivity, especially in respect to iron. The most significant parameters proved to be the solid to liquid ratio (S/L), the final pH value as well as the use of recycling of leachate on fresh BR batches. The proposed process, using sulfuric acid at low acid molarities under ambient conditions was integrated rapidly leading to high and selective Sc recovery. A flow diagram of the developed leaching process in industrial scale was proposed based on continuous operation.

Sepsis is a life-threatening syndrome triggered by infection and accompanied by high mortality, with antimicrobial resistances (AMRs) further escalating clinical challenges. Rapid and reliable detection of causative pathogens and AMRs are key factors for fast and appropriate treatment, in order to improve outcome in septic patients. However, current sepsis diagnostics based on blood culture is limited by low sensitivity and specificity while current molecular approaches fail to enter clinical routine. Therefore, we developed a Suppression PCR-based selective enrichment sequencing approach (SUPSETS), providing a molecular method combining multiplex suppression PCR with Nanopore sequencing to identify most common sepsis-causative pathogens and AMRs using plasma cell-free DNA. Applying only 1 mL of plasma, we target eight pathogens across three kingdoms and ten AMRs in a proof-of-concept study. SUPSETS was successfully tested on first ten clinical samples and revealed comparable results to clinical metagenomics while clearly outperforming blood culture. Several clinically relevant AMRs could be detected additionally. Furthermore, SUPSETS provided first pathogen and AMR-specific sequencing reads within minutes of starting sequencing, thereby potentially decreasing time to results to 11 - 13 hours and suggesting diagnostic potential in sepsis.

Dynamic virtual testing by Hardware in the Loop (HIL) real time simulation systems is common to minimize physical tests to validate and verify control algorithms, logics and software, under normal and emergency conditions. The accurate but costly HIL models setup activities could have an extended use to simulate faulty conditions that are seldom observable in the real system, yet they must be detected in advance and recognized. Data driven diagnostic methods have reached a mature development, in various sectors, proving effective in early detecting slowly varying deviations from nominal patterns of signals, even without a priori knowledge of their nature and behavior. These methods rely on vast amount of data logged from real systems that are ever and ever richer of monitoring telemetries that are worth being exploited. However, due to the usually reliable and safe systems being managed, it is often difficult to collect enough data on anomalous situations to validate fault detection and isolation and limit false positives. HIL model-based simulations allow generating and observing operational domains or transients rarely observed in real operations. This allows identifying the signals that are most correlated to faults and that could be selected to setup data-based diagnostic models of parts or subsystems, which are more suitable than the whole HIL model for online diagnostics, as well as to identify the features and trends that are most symptomatic of anomalous conditions.

Perovskite solar cells (PSCs) are vital for their optical and electrical properties, with lead-based PSCs reaching a remarkable efficiency of 26.1%, while tin-based counterparts achieve 18.71%. Due to lead's toxicity, there's a push for alternatives like tin. However, tin-based PSCs suffer from stability issues and high defect density states, necessitating the development of cost-effective, high-performance, and eco-friendly alternatives. In this study, we designed a hetero-junction architecture using MASnI3-based Perovskite, opti-mized with SCAPs-1D. After exhaustive analysis, our device achieved a power conversion efficiency of 24.18%, with enhanced parameters including Voc of 0.09323V, Jsc of 30.8360 mA/cm2, and FF of 84.10%. Recombination rates, particularly Shockley-Read Hall recom-bination, were significantly reduced. Parametric analyses, encompassing absorber layer thickness, band gap, defect density, doping concentration, and operating temperature, in-dicate potential efficiency enhancements. This underscores the viability of Sn-based PSCs as a cost-effective, efficient, and environmentally benevolent alternative to lead-based counterparts, promising advancements in future research and development efforts.

The article discusses issues related to the optimization of the operation of medium voltage networks, focusing on the optimization of network division points and the selection of the optimal network configuration aimed at reducing power and energy losses. The article provides a critical review of selected scientific works from recent years on the issue of network configuration optimization. The developed solution uses non-deterministic network models and statistical and probabilistic approaches. Optimization studies were carried out using heuristic optimization methods and proprietary algorithms for forecasting the load and power generated from renewable energy sources. The solution proposed in the article has many application possibilities. It can be used to optimize the location of network division points (reducing economic costs related to the modernization of network infrastructure) as well as to optimize the reconfiguration process in order to reduce power losses while maintaining voltage criteria.

Base excision repair (BER) is the predominant pathway to remove most forms of hydrolytic, oxidative and alkylative DNA damage. The precise functioning of BER is achieving by the regulation of each step by regulatory/accessory proteins, with the most important of which being poly(ADP-ribose) polymerase 1 (PARP1). The PARP1 regulatory functions extend to many cellular processes including regulation of mRNA stability and decay. PARP1 can therefore affect BER both at the level of the BER proteins and at the level of their mRNAs. Systematic data on how the PARP1 content affects the activities of key BER proteins and the levels of their mRNAs in human cells are extremely limited. In this study the CRISPR/Cas9 based technique has been used to knocked out the PARP1 gene in the human HEK 293FT line. The obtained cell clones with putative PARP1 deletion were characterized by several approaches including: PCR analysis of deletions in genomic DNA, Sanger sequencing of genomic DNA, qPCR analysis of PARP1 mRNA, western-blot analysis of whole-cell-extract proteins with anti-PARP1 antibodies, and the PAR synthesis in the whole-cell-extracts. qPCR analysis of mRNAs coding the BER related proteins: PARP2, uracil DNA glycosylase 2, AP endonuclease 1, DNA polymerase β, DNA ligase III and XRCC1 did not reveal crucial influence of PARP1 knockout. The corresponding catalytic activities in the whole-cell extracts (WCEs) evaluated in parallel did not differ significantly between mutant and parental cell lines. No considerable influence of poly(ADP-ribose) synthesis on the activity of the above WCE enzymes was revealed.

The copolyester of 3-hydroxybutyrate (3HB) and 3-hydoxyhexanoate (3HHx), PHBHHx, is a bi-odegradable plastic that has a high flexibility, softness, wide process window and marine bio-degradability. PHBHHx is usually produced from structurally related carbon sources such as vegetable oils or fatty acids but not from inexpensive carbon sources like sugars. In the previous studies, we demonstrated that engineered strains of hydrogen-oxidizing bacterium, Cupriavidus necator synthesized PHBHHx with high cellular content from not only sugars but also from CO2 as the sole carbon source in the flask culture. In this study, highly efficient production of PHBHHx from CO2 was investigated by pH-stat jar cultivation of the recombinant C. necator strains with feeding the substrate gas mixture (H2/O2/CO2=8:1:1) to complete mineral medium in recycled-gas closed-circuit culture system. As the result with the strain MF01/pBPP-ccrMeJAc-emd, the dry cell mass and PHBHHx concentration reached up to 59.62 ± 3.18 g･L-1 and 49.31 ± 3.14 g･L-1, respectively after 212 h of jar cultivation with limited addition of ammonia and phosphate solutions. The 3HHx composition was close to 10 mol% which is suitable for practical applica-tions. It is expected that autotrophic cultivation of the recombinant C. necator can be a feasible process for mass production of PHBHHx from CO2.

The rapid urbanization in China has significantly contributed to the vast expansion of urban built-up areas. Precisely extracting and monitoring these areas is crucial for understanding and optimizing the developmental process and spatial attributes of smart, compact cities. However, most existing studies tend to focus narrowly on a single city or global scale with a single dimension, often ignoring mesoscale analysis across multiple urban agglomerations. In contrast, our study employs GIS and image processing techniques to integrate multi-source data for the identification of built-up areas. We specifically compare and analyze two representative urban agglomerations in China: the Yangtze River Delta (YRD) in the east and the Chengdu-Chongqing (CC) region in the west. We use different methods to extract built-up areas from socio-economic factors, natural surfaces, and traffic network dimensions. Additionally, we utilize a high-precision built-up area dataset of China as a reference for verification and comparison. Our findings reveal several significant insights: (1) The multi-source data fusion approach effectively enhances the extraction of built-up areas within urban agglomerations, achieving higher accuracy than previously employed methods. (2) Our research methodology performs particularly well in the CC urban agglomeration. The average precision rate in CC is 96.03%, while the average precision rate in YRD is lower at 80.33%. This study provides an objective and accurate assessment of distribution characteristics and internal spatial structure of built-up areas within urban agglomerations. This method offers a new perspective for identifying and monitoring built-up areas in Chinese urban agglomerations.

Microwave radiation diagnosis technology can detect thermal changes in skin tissue earlier than anatomical changes, but its detection accuracy is limited by non-target radiation interference in the measurement environment, additional measurement errors of system units, and energy scattering and transmission between skin tissues. This paper aims to address the scientific challenges of analyzing the forward and inversion modelling detection mechanism of layered accurate temperature measurement of human skin tissue based on multi-band. The study focuses on the construction of a pencil beam antenna optimization system, the optimization strategy of high-sensitivity correlated radiometer architecture, and the high-precision multi-band forward and inversion modelling detection algorithm. The key technologies include: (1) A new method of integrated modeling and multi-index optimization of antenna with high directivity and small aperture is proposed, and a priori knowledge-guided neural network of pencil beam distribution is constructed to realize the inversion model of antenna structural parameters; (2) The influence mechanism of high sensitivity correlated radiometer architecture error is analyzed, and a periodic phase shift error correction algorithm based on uniform polar circle is designed; (3) Combining deep learning theory and hyperparameter optimization framework, an iterative model is established, and the objective function modified by the penalty factor is defined to realize a new detection method combining forward and inversion. This paper presents a theoretical foundation for the industrialization of microwave radiation diagnostic technology.

Urbanization and climate change have increased the need for stormwater management and nature-based solutions. Decisions made at project level impact the emergence of systemic traits of the stormwater network and the functionality of the catchment areas in urban planning. To that end, it is vital to introduce the decision-making tools for analyzing both the utilities and amenities of nature-based solutions (NBS) to increase their adoption to reduce the peak loads in the stormwater system, and to that end, mitigate the impacts of climate change. This paper demonstrates a workflow using drone-based photogrammetry, 3D modeling, and simulation software to generate visual and functional models assisting in informed decision-making in the design of stormwater systems as functional landscape architecture. Using aerial data from drones and modeled design solutions, the proposed workflow simulates rain events, infiltration, evaporation, water flow, and accumulation of stormwater in a way that allows the visual and quantified analysis of detailed landscape architecture designs. The paper provides an example of a rooftop site simulation demonstrating the infiltration and flow of water to the drainage. The visual decision-making method provided can aid in investment decisions for functional landscape design in support of stormwater management.

New [1,2]dithiolo[3,4-b]pyridine-5-carboxamides were synthesized through the reaction of dithiomalondianilide (N,N'-diphenyldithiomalondiamide) with 3-aryl-2-cyanoacrylamides or by a three-component reaction involving aromatic aldehydes, cyanoacetamide and dithiomalon- dianilide in the presence of morpholine. The structure of 6-amino-4-(2,4-dichlorophenyl)- 7-phenyl-3-(phenylimino)-4,7-dihydro-3H-[1,2]dithiolo[3,4-b]pyridine-5-carboxamide was con-firmed using X-ray crystallography. To understand the reaction mechanism in detail, density functional theory (DFT) calculations were performed with a Grimme B97-3c composite computa-tional scheme. The results revealed that the rate limiting step is a cyclization process leading to the closure of 1,4-dihydropyridine ring with an activation barrier of 28.8 kcal/mol. Some of dithiolo[3,4-b]pyridines exhibited moderate herbicide safening effects against 2,4-D . Additional-ly, ADMET parameters were calculated and molecular docking studies were performed to identify potential protein targets.

Heat exchangers play a vital role in numerous sectors like power generation and automotive manufacturing. Enhancing the energy efficiency of these exchangers stands as a significant hurdle. Utilizing nanofluids emerges as an optimal solution to augment heat transfer rates, leveraging their superior thermal conductivity while addressing economic constraints linked with traditional heat exchanger technologies. The motivation for this study is to consider the comprehensive synergistic features of MWCNTs, SiO₂, and hybrid MWCNTs–SiO₂ EG-based nanofluids in plate heat exchangers. This was achieved by simulating a plate heat exchanger using CFD (Fluent and Gambit softwares) considering the comparison of two SiO₂, MWCNTs, and their hybrid forms at different mass concentrations. The Reynolds-Averaged Navier-Stokes (RANS) method was employed to model turbulent flows, and the nanoparticles were compared in both single-phase and two-phase states, with their properties derived from experimental studies. Moreover, Nusselt number, convective heat transfer coefficient, and pressure drop variations were computed at different Reynolds numbers. The findings indicated an increase in the Nusselt number with the incorporation of the hybrid nanofluid, achieving a maximum enhancement of 11.19% in comparison to EG at a Reynolds number of 240 and a concentration of 0.86 wt.%. Noticeably, the pressure drop remained negligible at lower Reynolds numbers, exhibiting marginal variations up to 0.3% at higher Reynolds numbers. At a concentration of 0.86 wt.% and a Reynolds number of 480, the introduction of MWCNTs, hybrid, and SiO₂ nano-additives resulted in respective increases in the heat transfer coefficient by 21.02%, 10.76%, and 2.16% and corresponding alterations in pressure drop of 0.11%, 0.04%, and 0.02%.

Ming-style round-backed armchairs as a classic Chinese chair design are renowned for the blend of ergonomics, practicality, and elegance. Although the Chinese armchair furniture industry has made strides in sustainability, there is still a need for further improvements in material selection, manufacturing processes, and supply chain management to fully support the development of sustainable furniture. Laminated bamboo lumber as new sustainable materials are becoming a popular option for furniture designers in the era of "sustainable design". This research aims to investigate the feasibility and application of laminated bamboo lumber in the design of Chinese armchair furniture and proposes innovative ideas for optimizing the armchair's design. First, an empirical study was conducted to comprehensively understand the classification of Ming-style round-backed armchairs’ structure to develop a 3D model. Secondly, an experimental research method was then employed to explore the parameters of laminated bamboo lumber for future studies. Additionally, a validation experiment was conducted to compare real-world scenarios with simulations using finite element analysis in Ansys. Finally, finite element analysis was used to test the feasibility and application of laminated bamboo lumber in furniture design, focusing on the material’s mechanical properties. Results indicated that laminated bamboo lumber has excellent mechanical properties as furniture design materials, subsequently, using the optimized results, the use of 0.6319 kg of steel was successfully reduced by 23.68% to ensure the armchair’s stability. This provides a reference for the future compter-assist and standardized innovative design of Chinese armchair. By incorporating compter-assist design and lightweight optimization, it is possible to save materials and make more efficient use of resources, thereby contributing to sustainable development goals in the field of furniture design.

Monitoring the integrity of aeronautical structures is fundamental for safety. Structural Health Monitoring Systems (SHMS) perform real-time monitoring functions, but their performances must be carefully assessed. In this work the damage detection performances of a strain-based SHMS, were evaluated on a composite helicopter rotor blade root. The SHMS monitored the bonding between the central core and the surrounding antitorsional layer. A damage detection algorithm was trained through Finite Element analyses performed on the component. The effects of the loads variability and of damages were decoupled by including a load recognition step in the algorithm. Load recognition was accomplished in different ways: version#1 adopted an Artificial Neural Network (ANN) trained on blades in pristine condition; version#2 was trained also on damaged blades; version#3 adopted a calibration matrix method. Anomaly detection, damage assessment, and localization were performed by using an ANN. Results showed a higher load identification and anomaly detection accuracy for version#1 and version#2 compared to version#3. Gaussian noise reduced anomaly detection and damage assessment performances, and reduced damage localization accuracy for bigger damages. The damage detection performance were obtained for a fibre optic based-SHMS, including the trade-off between probability of detection and false alarm rate for different damage sizes.

The blood counts of α thalassemia carriers (α-thal) are similar to those of β thalassemia carriers, except for Hgb A2 that is not elevated. The objective of this study was to determine whether mathematical formulas are effective for detecting suspected α-thal. The data were obtained from the database of the prevention program for detecting couples at risk for having a child with hemoglobinopathy. RBC indices were analyzed using mathematical formulas and the sensitivity and negative predictive value (NPV) calculated. Among 1334 blood counts suspected α-thal analyzed, only the Shine&Lal and the Support Vector Machine formulas revealed high sensitivity and NPV. Sensitivity was 85.54 and 99.33% and NPV 98.93 and 99.93%, respectively. Molecular defects were found in 291, 81 had normal α genes. Molecular analysis was not performed in 962. Based on these results, mathematical formulas incorporating one of these reliable formulas for detecting suspected α or β thalassemia carriers in the program of the automatic analyzers can flag these results and increase the awareness of the primary physicians about the carrier risk and send an alert with a recommendation for further testing.

The search for molecular biosignatures at the surface of Mars is complicated by an intense irradiation in the mid- and near- ultraviolet (UV) spectral range for several reasons: (i) many astrobiologically relevant molecules are electronically excited by efficient absorption of UV radiation and rapidly undergo photochemical reactions; (ii) even though the penetration depth of UV radiation is limited, aeolian erosion continually exposes fresh material to radiation; and (iii) UV irradiation generates strong oxidants such as perchlorates that can penetrate deep into soils and cause subsurface oxidative degradation of organics.As a consequence, it is crucial to investigate the effects of UV radiation on organic molecules embedded in mineral matrices mimicking the martian soil, in order to validate hypotheses about the nature of the organic compounds detected so far at the surface of Mars by the Curiosity rover, as well as organics that will be possibly found by the next rover missions Mars 2020 and ExoMars 2020. In addition, studying the alteration of possible molecular biosignatures in the martian environment will help to redefine the molecular targets for life detection missions and devise suitable detection methods.Here we report the results of mid-UV irradiation experiments of Mars soil analog samples obtained adsorbing relevant organic molecules on a clay mineral that is quite common on Mars, i.e. montmorillonite, doped with 1 wt% of magnesium perchlorate. Specifically, we chose to investigate the photostability of a plausible precursor of the chlorohydrocarbons detected on Mars by the Curiosity rover, namely phthalic acid, along with the biomarkers of extant life L-phenylalanine and L-glutamic acid, which are proteomic amino acids, and adenosine 5’-monophosphate, which is a nucleic acid component.We monitored the degradation of these molecules adsorbed on montmorillonite through in situ spectroscopic analysis, investigating the reflectance properties of the samples in the Near InfraRed (NIR) spectral region. Such spectroscopic characterization of molecular alteration products provides support for two upcoming robotic missions to Mars that will employ NIR spectroscopy to look for molecular biosignatures, through the instruments SuperCam on board Mars 2020, ISEM, Ma_Miss and MicrOmega on board ExoMars 2020.

Making sustainable business models, especially in manufacturing, is a key approach for organizations to adopt in order to create more sustainable processes. New technologies are needed to implement new policies that can minimize the economic, environmental, and social consequences of industrial activity. Sustainable maintenance is decisive to guarantee the availability, reliability, and safety of assets, surpassing traditional maintenance policies and embracing the principles of the circular economy. The main objective of Maintenance 4.0 is to increase the lifespan and availability of the equipment by preventing unplanned downtime, reducing planned shutdowns, and improving safety. This research focuses on the integration of advanced Industry 4.0 tools with conventional monitoring and control techniques in process industries. The article suggests that while complex neural networks might provide good predictions, simpler solutions can generalize well and have lower prediction errors because they can capture the underlying relationships between variables in a specific asset better. The combination of maintenance function, Industry 4.0 tools, and advanced statistical solutions to obtain sustainable processes can facilitate organizational change and aid decision-making in equipment management. These solutions seek to reduce interruptions and expenses through the unnecessary utilization of labor and spare parts. All these considerations improve communication and data processing, resulting in improved maintenance of a hydrogen compressor in the petrochemical industry.

The characteristics of tight sandstone, such as small pores, complex pore structures, low permeability, and low porosity, make it difficult to accurately characterize its pore structure. This represents a major challenge in the exploration and development of tight sandstone oil and gas reservoirs. This article conducts a simulation study on the impact of characteristic parameters such as pore size, coordination number, pore-throat ratio, and wettability on microscopic remaining oil after polymer flooding, thereby quantifying the types of remaining oil.

One of the strategies to reduce the contents of the low density lipoproteins (LDLs) in a blood is a hemoperfusion, in which case they are selectively retracted from plasma by an adsorber located outside the patient body. Recently, a photo-controllable smart surface was developed for this purpose characterised by high selectivity and reusability [C.Guo et al., ACS Applied Materials & Interfaces 2022, DOI:10.1021/acsami.2c07193]. We present a mesoscopic model for such a setup involving the azobenzene-containing polymer brush and the model LDL particles. The latter comprise an uniform spherical core covered by a shell of elongated particles representing phospholipids. The system is studied using the coarse-grained molecular dynamics simulation. We examined the dependences of the binding energy on both the length of polymer chains and the grafting density of a brush, and established optimal conditions for the adsorption. These are explained by a competition between the concentration of azobenzenes and phospholipids in the same spatial region, flexibility of polymer chains, and excluded volume effects.

The paper formulates requirements for a polymer material for molding products from it by fused deposition modeling. A methodology for evaluating the suitability of a polymer or composite of thereof in 3D printing technology has been developed. A graphic representation of the developed methodology in the form of a temperature-shear rate logarithm diagram is proposed. Application of the proposed methodology makes it possible to simplify the development of new materials for 3D printing by fused deposition modeling both at the stage of selecting the components of the polymer composition and at the stage of its subsequent approbation.

The marketing industry is rapidly evolving, necessitating educational programs to adapt and equip graduates with relevant skills and knowledge. This systematic literature review with bibliometric analysis (SLRBA) explores the integration of Problem-Based Learning (PBL) in marketing education. PBL is an instructional strategy that empowers students to solve real-life problems by integrating theory and practice, thus fostering critical thinking and decision-making skills. Our review synthesizes data from 71 sources, highlighting the definition of PBL, strategies to promote its implementation in marketing education, and the benefits and challenges associated with this approach. The findings indicate that PBL enhances student engagement, provides hands-on experience, and prepares students for real-world marketing challenges. Strategies such as using social media, serious games, e-learning, and feedback mechanisms are discussed for their effectiveness in promoting active learning and student participation. Despite its advantages, PBL faces challenges such as resource intensiveness, student resistance, and information integrity issues. This review underscores the importance of PBL in bridging the gap between theoretical knowledge and practical application, ultimately preparing marketing students to meet the demands of the industry. The paper concludes with recommendations for future research and best practices for implementing PBL in marketing education.

The development of Artificial Intelligence-based tools is having a big impact on industry. In this context, the maintenance operations of important assets and industrial resources are deeply changing both from a theoretical and a practical perspective, even in the field of ship propulsion systems. Namely, conventional preventive maintenance schedules audits and checks at fixed times by using statistics on component failures, but it can be improved by a predictive maintenance based on the real component health status, which is inspected by proper sensors. In this way, time and costs are saved. More in details, data-driven models, through Machine Learning (ML) algorithms, generate the expected values of monitored variables for comparison with real measurements coming from the asset, hence for a diagnosis based on the difference between expectations and observations. Then, a ML-based fault detection starts with the choice of the ML algorithm. This process is often not the consequence of an in-depth deep analysis of the different algorithms available in the literature. For that reason, the authors propose a simple procedure to support a first implementation stage of the so-called Condition Based Maintenance (CBM): a quick benchmarking of the most suitable ML algorithms useful for fault detection. The algorithms are compared by taking into account not only the algorithm output error, shown by the Mean Squared Error between predictions and data, but also the response time, which is a crucial variable for maintenance purpose.

The present study aims to unravel the mechanisms of salicylic acid and rehydration and the physiological benefits in pepper plants grown under water deficit. 3x4 factorial scheme adopted, with three water regimes (irrigated, dry and rehydration) and four SA concentrations, namely: 0 (control), 0.5, 1 and 1.5 mM. Evaluated leaf moisture percentage, leaf water potential, chlorophylls (a and b), carotenoids, stomatal conductance, chlorophyll a fluorescence and H2O2 concentration at different times throughout the day and water conditions (irrigated, dry and rehydration) and SA applications (without the addition of the regulator (0) and with SA addition at concentrations equal to 0.5, 1 and 1.5 mM). Exogenous SA application favored stomatal conductance responses(gs) and modified fluorescence parameters (Fm, Fo, Fm', Fo', Fv/Fm, qP, ETR and NPQ) of sweet pepper plants subjected to drought followed by rehydration. SA concentration of 0.5 mM allowed a more expressive recovery of gs indices, effective quantum yield of photosystem II, with emphasis on excess energy (E) and maximum quantum yield (FV/FM) over time in plants subjected to drought and rehydration. We discovered that the use of SA, especially in association with rehydration, by modulating the variables gs and chlorophyll a fluorescence, prevents damage to membranes and consequently mitigates water deficit in pepper plants.

Cisplatin (CDDP) is widely used to treat several types of cancer. However, CDDP induces nephrotoxicity. This toxicity could be avoided, applying a lower cisplatin dose; however, it could induce a lesser therapeutic activity. In this paper, we present the cytotoxic activity against prostate human cancer cell line (PC-3) of the combination of CDDP with masticadienonic acid (MDA), a triterpene isolated from Amphypterygium adstringens.The combinations A (half of the IC₅₀), B (IC₅₀) and C (twice IC₅₀ of the compounds) in a radio 1:1 were evaluated. Our results showed that the B and C combinations presented synergism effect. However, B combination showed almost 100% inhibition of cell proliferative activity and increased apoptosis compared with those presented by each compound apart. A pretreatment of MDA 24 h to cells before the CDDP, AMD or B combination administration result in a resistance to the treatments. A xenograft study using PC-3 cells showed that the combination of 47.5 mM/kg (AMD) plus 4 mM/kg (CDDP) administered weekly for 3 weeks reducing the tumor volume in approximately 47 %. However, the combination of 47.5 mg/kg (AMD) plus 2 mg/kg (CDDP) administered every third day for 21 days reduce, approximately 82% of tumor compared with mice no treated.

This study was aimed to investigate the effect of xylan depolymerizing enzyme namely endo-xylanase (Xyn) combined with debranching enzymes namely arabinofuranosidase (Afd) and feruloyl esterase (FE) on digestion, growth performance and intestinal volatile fatty acid profile of piglets. The in vitro experiments were firstly conducted to examine the enzymological properties of Xyn, Afd and FE, the synergy among these enzymes, together with the effect of combination of these enzymes on digestion of piglet diet. The in vivo experiment was then implemented by allocating 270 35-d-old postweaning piglets into 3 treatment groups: control group, Xyn group and (Xyn+Afd+FE) group. Each group had 6 replicates (15 piglets/replicate). The results revealed a satisfying thermostability and pH stability of Xyn, Afd and FE. Combination of Xyn, Afd and FE had a superiority (P < 0.05) over Xyn alone and its combination with Afd or FE in promoting degradation of different bran fibers rich in arabinoxylan (Abx). Treatment with combination of Xyn, Afd and FE had advantages over Xyn alone to induce increasing trends (P < 0.10) of in vitro digestibility of dietary nutrients (dry matter, crude protein, crude ash and gross energy) and piglet growth performance (average daily gain, final body weight and feed efficiency), concurrent with a reduction (P < 0.05) of diarrhea rate and increases (P < 0.05) in cecal acetic acid, butyric acid and total volatile fatty acids concentrations as well as pH value of piglets. Collectively, combination of Xyn, Afd and FE was efficient in benefiting degradation of Abx in brans, as well as improving digestion, growth performance and intestinal volatile fatty acid profile of piglets.

Market crises pose significant challenges for businesses, emphasizing the importance of effective crisis management strategies. Central to these strategies is the ability to identify and retain loyal customers, who often serve as the bedrock of stability during tumultuous times. This paper investigates the application of deep meta-learning analysis to predict loyal customers as a cornerstone of market crisis management. Drawing upon an extensive literature review, the study explores previous research on market crises, customer loyalty, and the evolution of deep learning and meta-learning in crisis management contexts. Methodologically, the paper outlines data collection, model development, and evaluation procedures tailored for deep meta-learning-based customer prediction. In results, the overall accuracy of model 85%, a precision 0.88, recall 0.82, and F1-score 0.85 were obtained. The analysis demonstrates the effectiveness of deep meta-learning models in accurately identifying loyal customers during market crises, offering insights into their performance and applicability compared to traditional methods. Practical implications include potential applications in crisis management for businesses and considerations for real-world implementation.

The fish supply chain (FSC) industry faces a significant challenge in terms of maintaining fish quality and authenticity throughout the chain. The main goal of modern FSC systems is tracking and tracing the fish product at each stage, from harvester to end customer, as well as assessing its quality and authenticity. Integrating FSC with new technologies, such as Blockchain (BC), Big Data, Artificial intelligence (AI), and Internet of Things (IoT), enhances fish product traceability, authenticity, visibility, and security. We propose a BC-based FSC framework that follows a layered architecture consisting of a SC layer, an IoT layer, and a BC layer. We integrate a new AI-based hand-held device, a Quality, Adulteration & Traceability (QAT) device, that can identify fish species and assess fish quality. We leverage the key features of BC and smart contracts, deployed over the Ethereum platform for the proposed framework integrated with QAT technology. Extensive validation of smart contracts is conducted to prove its practical feasibility.

The present study aims to develop an efficient numerical method for computing the diffraction and radiation of water waves with horizontal long cylindrical structures, such as floating breakwaters. A higher-order scheme is used to discretize geometry of the structure as well as the relevant physical quantities. As the kernel of this method, Wehausen’s free-surface Green function is calculated by a newly-developed Gauss-Kronrod adaptive quadrature algorithm after elimination of its Cauchy-type singularities. To improve computational efficiency, a Chebyshev approximation approach is applied to a fast calculation of the Green function that needs evaluation thousands of times. In addition, OpenMP parallel technique is used to the formation of influence coefficient matrix, which significantly reduces CPU time. Finally, computations are performed on wave exciting forces and hydrodynamic coefficients for the long cylindrical structures, either floating or submerged. Comparison with other numerical and analytical methods demonstrates good performance of the present method.

This study presents the development of a diglycidyl monomer containing two imine groups that can act as dynamic and reversible bonds. During the curing of the monomer with two different amine hardeners, we confirmed the formation of new imine groups due to the transamination reaction, not reported before, between the imine groups of the diepoxy monomer with the amine groups of the hardener. The effect of this structural change is observed for the first time in the stress relaxation behavior, resulting in the overlapping of two different relaxation modes. The analytical modelling could extract two distinct characteristic relaxation times using a double-element Maxwell model. A second characterization of the stress relaxation process by frequency sweep experiments was performed to corroborate the results obtained, confirming speedy stress relaxation. Acid-catalyzed hydrolysis was performed on the studied materials, demonstrating the complete degradation of the network. We finally confirmed that the synthesized diepoxy compound is suitable for preparing carbon fiber-reinforced composite materials, demonstrating easy fiber impregnation, fast reshaping and especially a total degradation of the polymer matrix that allows the recovery of the carbon fibers in mild conditions. This epoxy-amine system is an excellent candidate for overcoming the traditional limits of thermosets in preparing fiber-reinforced composites.

The burden of hypertension remains unacceptably high globally, particularly in low- and middle-income countries (LMICs). Workplace offer enormous potential as an idea setting for early detection and treatment of hypertension among the working class. Analysis of such a Workplace Screening Programme can reveal information about its potential impact. Machine learning techniques such as k-Means Clustering are untapped tools for such analyses. We set out to deploy this tool for the analysis of our university annual medical screening of workforce for hypertension. An anonymized dataset containing the demography and blood pressure measurements values obtained from staffs of different departments/units in an academic institution was obtained. The total number of samples or data points are 1, 723 in which the input dataset contains six features, including year category (2018, 2019, 2021,2022), Department/Unit (academic and non-academic), gender (male and female), while the target output is the blood pressure status (low, normal and high) respectively. Analysis of the dataset was carried out using machine learning techniques. In this retrospective analysis, it was observed that the mean age for this working class is 42 years old. Similarly, it was discovered that hypertension was prevalent among members of staff above the age of 40 irrespective of their gender or professional category (academic or non-academic). The analysis also revealed that there was a steady decline in the prevalence of hypertension from 2018 to 2022. From the research, it is evident that the adoption of machine learning techniques for periodic analyses of workplace health status screening initiative (especially for hypertension) is effective, feasible, and sustainable to diagnose and control hypertension among the working class.

Electromobility promises to efficiently mitigate consequences of increasing traffic volume and its accompanied greenhouse gas emissions. On an individual level, electrified bikes allow emission free electrified mobility at moderate costs and consequently their stock has increased significantly in recent years. This simultaneously increases the demand for spare parts, which are often manufacturer or application-specific, and due to many variants, challenging to provide for the market. This article evaluates powder-based and extrusion-based metal additive manufacturing of a typical electrified bike component to demonstrate an alternative spare parts supply. The investigation demonstrates how these parts can be additively manufactured function equivalent and with sufficient mechanical properties, also taking economical aspects into account. Furthermore, the needed resources and related environmental consequences for metal-based additive manufacturing spare-part production are compared for both process routes. The results show that both routes are capable of producing spare-parts at comparatively same mechanical performance and resource costs, while needed resources such as energy, gases and manufacturing time are significantly lower for powder-based, respectively machine costs for extrusion-based additive manufacturing. Therefore, additive manufacturing offers a promising opportunity to produce parts in small quantities resource efficient and rapidly.

Fragile X syndrome (FXS) is caused by the full mutation in the FMR1 gene on the Xq27.3 chromosome region. It is the most common monogenic cause of Autism Spectrum Disorder (ASD) and inherited intellectual disability (ID). Besides ASD, ID and other issues, individuals with FXS may exhibit sleep problems and impairment of circadian rhythm (CR). The Drosophila melanogaster models of FXS, such as dFMR1B55, present excellent model for research in the FXS field. During this study, sleep pattern and CR in dFMR1B55 mutants were analyzed, using a new platform based on continuous high-resolution videography in integration with a highly-customized version of software. This methodology provides more sensitive results, which could be crucial for all further research in this model of fruit flies. The study revealed that dFMR1 B55 male mutants can be considered weak rhythmic flies rather than totally arrhythmic, and present a good alternative animal model of genetic disorder, which includes impairment of CR and sleep behavior. The combination of videography and software used in the current study should be recommended as a gold-standard methodology for such further research.

Focusing on the problem of identifying and classifying aero-engine models, this paper measures the infrared spectrum data of aero-engine hot jets using a telemetry Fourier transform infrared spectrometer. Simultaneously, infrared spectral data sets with the six different types of aero-engines are created. For the purpose of classifying and identifying infrared spectral data, a CNN architecture based on the continuous wavelet transform peak seeking attention mechanism (CWT-AM-CNN) is suggested. This method calculates the peak value of middle wave band by continuous wavelet transform, and the peak data is extracted by the statistics of the wave number locations with high frequency. Attention mechanism is used for the peak data, and the attention mechanism is weighted to the feature map of the feature extraction block. The training set, vali-dation set and prediction set are divided in the ratio of 8:1:1 for the infrared spectral data sets. For three different data sets, CWT-AM-CNN proposed in this paper is compared with the classical classifier algorithm based on CO2 feature vector and the popular AE, RNN and LSTM spectral processing networks. The prediction accuracy of the proposed algorithm in the three data sets is as high as 97%, and the lightweight network structure design not only guarantees high precision, but also has a fast running speed, which can realize the rapid and high-precision classification of the infrared spectral data of the aero-engine hot jets.

Proteins play a pivotal role in supporting athletes by promoting muscle hypertrophy and minimizing protein catabolism during exercise. They stimulate muscle protein synthesis, aiding in the repair of exercise-induced muscle damage and serving as an energy source, particularly for post-exercise glycogen replenishment. In individuals with phenylketonuria (PKU), for whom protein intake is limited to essential phenylalanine (Phe), supplementation with Phe-free amino acids or glycomacropeptides is necessary. Tailored for macronutrient and micronutrient content, these protein substitutes fulfill most protein requirements, but lack Phe, unlike dietary sources of protein. Protein requirements for athletes with PKU exceed general recommendations due to limited availability in supplements and potential catabolism mitigation. Various factors influence tolerated dietary Phe in PKU, including protein substitute quantity, distribution, pharmacological treatment, age, growth rate, pregnancy, catabolic states, and physical activity. While general protein requirements for PKU surpass those of the general population, adherence to supplement regimens is crucial for athletes and patients with PKU. Strategically timed protein substitutes enhance muscle protein synthesis, body composition, and sports performance within safety limits. Individualized intake is essential for optimal outcomes, as proteins have a multifaceted role in optimizing athletic performance and addressing challenges in PKU.

Dermal injections of hyaluronic acid gel for aesthetic skin rejuvenation are increasingly popular nowadays. Although these products are classified as medical devices, the regulations on their administration by licensed practitioners are still weak, whereas their manufacturers increasingly highlight and advertise the cellular effects that underpin the efficacy of these injections. In this re-view, we discuss all current knowledge on the mode of action of dermally injected hyaluronic acid and the potential toxicological implications especially from crosslinked gels in conjunction with the current global regulations. We conclude that dermal injections of hyaluronic acid have several therapeutic implications that warrant further research, and that strict regulations must be applied on their manufacture/quality control and the required qualifications of licensed aesthetic injectors.

The determination of the specific surface free energy, specific properties and Lewis’s acid base of solid materials is of capital importance in many industrial processes such as adhesion, coatings, two dimensional films and adsorption phenomena. (1) Background: The physicochemical properties of many solid particles were characterized during the last forty years by using the retention time of injected well-known molecules into chromatographic column containing the solid substrates to be characterized. The obtained net retention time of the solvents adsorbed on the solid allowing the determination of the net retention volume directly correlated to the specific surface variables, dispersive, polar and acid-base properties. (2) Methods: Many chromatographic methods were used to quantify the values of the different specific surface variables of the solids. However, one found a large deviation between the different results. In this paper, one proposed a new method that quantify the specific free energy of adsorption as well as the Lewis’s acid-base constants of many solid surfaces. (3) Results: The new applied method allowed us to obtain the specific enthalpy and entropy of adsorption of polar model organic molecules on several solid substrates such as silica, alumina, MgO, ZnO, Zn, TiO2 and carbon fibers. (4) Conclusions: our new method based on the separation between the dispersive and polar free surface energy allowed to better characterize the solid materials.

This study was conducted to recover valuable metals (silicon and silver) using acid leaching and substitution reactions with copper powder from the pulverized solar cell separated from the PV ribbon. Leaching experiments were conducted according to nitric acid concentration by molar solution as 1M, 2M, and 3M using an ultrasonic cleaner at a reaction temperature of 60 °C for the leaching times of 30 to 120 minutes. Si phases were detected at all leaching reaction times, it was confirmed that the aluminium was removed effectively if the nitric acid leaching time was more than 30 minutes, and silicon with a purity above 99% could be recovered. The silver was precipitated by adding copper, which has greater reducibility than Cu, Al, Si, Pb, and Sn. When the addition of copper powder was 0.75 and 1.0 g, precipitate was produced 0.23 and 0.55 g, respectively. The optimal condition for the recovery of silver by the addition of copper powder was 1 g, where is recovery rate reached 93.3%.

Alheira is a naturally fermented meat sausage traditionally made in the Portuguese region of Trás-os-Montes. Lactic Acid Bacteria (LAB) have been found to be the dominant microorganisms in alheira. This study aimed: 1) to characterize technological features and in vitro antimicrobial activity of LAB isolates; and 2) to reveal associations between such phenotypic characteristics and the isolates genotypically identified to species level through amplification and sequencing of the 16S ribosomal gene. Sixty-two LAB isolates were identified and Enterococcus faecium was the most prevalent (32.3%), followed by Leuconostoc mesenteroides (19.4%) and Latilactobacillus sakei (17.7%), aligning with previous research on traditional Portuguese fermented meat sausages. The phenotypic analysis of LAB isolates indicated diverse acidification capacities, proteolytic activities, and inhibitory effects against foodborne pathogens. Comprising the technological attributes, L. paracasei and L. mesenteroides had higher proteolytic activity (3.46 and 3.43 mm), whereas E. faecium and L. paracasei stood out for their acidifying capacity, with mean pH after 6 h of 5.78 and 6.03, respectively. Overall, lactobacilli presented higher inhibition diameter against the pathogens Staphylococcus aureus, Listeria monocytogenes and Salmonella Typhimurium. Although the mechanisms for inhibition of pathogen growth needs to be further elucidated, these findings enhance our understanding of LAB diversity and functionality in alheira sausages, contributing to product safety and quality assessment.

Oleanolic acid (OA) being the ubiquitous compound in the plant kingdom is studied for both the neuroprotective and neurotoxic properties. The mechanism of acetylcholinesterase (AChE) inhibitory potential of OA is investigated using the molecular dynamic simulations (MD) and docking as well as membrane-like and in vitro tests. There are also applied SH-SY5Y human neuroblastoma cells as well as in vivo on the zebrafish tests. The inhibitory potential towards the AChE enzyme is examined using the TLC-bioautography assay (the IC50 value is 9.22 μM). The CH- interactions between the central fragment of the ligand molecule and the aromatic cluster created by the His440, Phe288, Phe290, Phe330, Phe331, Tyr121, Tyr334, Trp84 and Trp279 side chains are observed. The in vitro tests carried out on the SH-SY5Y cells indicates that the viability rate is reduced to 71.5%, 61%, and 43% at the concentrations of 100 µg/mL, 300 µg/mL, and 1000 µg/mL, respectively after 48 hours of incubation whereas cytotoxicity against the tested cell line with the IC50 value is 714.32 ± 32.40 µg/mL. The in vivo tests on the zebrafish prove that there is no difference between the control and experimental groups as regards the mortality rate and morphology (P>0.05).

Among phosphorylated derivatives, phosphinates occupy a prominent place due to their ability to be bioisosteres of phosphates and carboxylates. These properties imply the necessity to develop efficient methodologies leading to phosphinate scaffolds. For the past years our team have explored the nucleophilic potential of silylated phosphonite towards various electrophiles. In this paper, we propose to extend our study over other electrophiles. We describe here the implementation of a cascade reaction between (trimethylsilyl)imidates and hypophosphorous acid mediated by a Lewis acid allowing the synthesis of aminomethylenebisphosphinate derivatives.

Ningxiang pigs exhibit a diverse array of fatty acids, making them an intriguing model for exploring the genetic underpinnings of Fatty acid metabolism. In this study, we conducted a genome-wide association study using a dataset comprising 50,697 SNPs and samples from over 600 Ningxiang pigs. Our investigation yielded novel candidate genes linked to five saturated fatty acids (SFAs), four monounsaturated fatty acids (MUFAs), and five polyunsaturated fatty acids (PUFAs). Re-markably, 37, 21, and 16 SNPs showed significant associations with SFAs, MUFAs, and PUFAs, respectively. Notably, ALGA0047587, H3GA0046208, DRGA0016063, and ALGA0031262 demonstrated substantial phenotypic variance (≥ 30%) in Arachidic acid (C20:0), Elaidic Acid (C18:1n-9(t)), and Arachidonic acid (C20:4n-6), respectively. Several significant SNPs were posi-tioned proximally to previously reported genes. In total, we identified 11, 6, and 5 candidate genes associated with SFAs, MUFAs, and PUFAs, respectively. These findings hold great promise for advancing breeding strategies aimed at optimizing meat quality and enhancing lipid metabolism within the intramuscular fat (IMF) of Ningxiang pigs.

Current low meat production in Omani goats under traditional feeding regimes justifies a study of the effects of Spirulina Platensis (SP) supplementation on goats’ performance. Hence, this study aimed to evaluate the effect of incorporating SP into diets on carcass characteristics, fatty acid profile and meat quality traits of two Omani goat breeds. Thirty-six eleven-month-old bucks from the Jabbali and Sahrawi goat breeds (n= 18/breed) were divided into three groups (control, Treatment 1, and treatment 2). All animals received a conventional concentrate feed ration (con-trol (CON) consisting of pellets creep fed. Animals were fed SP daily with Treatment 1 (T1) fed at 2g/head and Treatment 2 (T2) fed at 4g/head. Sahrawi bucks showed a highly significant response to SP feeding compared to Jabbali bucks. Average daily gain and carcass traits (body length, leg length and the rack weight) of Sahrawi bucks were significantly higher in the T1 group than in the CON group. The weights of omental and kidney fat increased in T1 group of Sahrawi goats, while it increased in T2 group of Jabbali goats compared to CON group. Ultimate pH increased in T1 group and meat color (lightness) increased in T2 group in both LD and SM muscles of Sahrawi goats. Most of PUFA n-6 and n-6/n-3 ratio increased in T1 group, while most of MUFA2 and PUFA n-3 fatty acids increased in T2 group of Sahrawi goats. In addition, a significant decrease in pentadecanoic and margaric acids of Sahrawi goats was observed by adding SP to the diet com-pared to the control group. The study concluded that incorporating SP (2g and 4g/head) into the diet of Omani goats, especially Sahrawi goats, can increase growth performance, improve fatty acid composition and meat quality.

Alginate films (2% w·v-1) were prepared with varying concentrations (5-20% w/w) of citric acid and aqueous grape seed extract (GSE) filtrate (11.66 ± 1.32 g GAE/L) by the solvent-evaporation method. Crosslinking alginate via ester bonds (FTIR analysis) with citric acid up to 10% (w/w) led to a 33% increase in tensile strength, a 34% reduction in water vapor transmission rate (WVTR), and had no impact on elongation at break. Crosslinking alginate with citric acid in presence of GSE increased the tensile strength by 17%, decreased WVTR by 21%, and significantly improved DPPH scavenging activity. Moreover, after incubation for 24 h at 37°C, the film-forming solutions exhibited increased antimicrobial activity, resulting in 0.5 and 2.5-log reductions for Escherichia coli and Staphylococcus aureus, respectively, compared to the values obtained without the addition of GSE. The stronger inhibitory effect observed against Gram-positive bacteria can be attributed to the unique composition and structure of their cell walls, which create a barrier that restricts the penetration of polyphenols into the cells. pH adjustment of the GSE film-forming solution from 2.0 to 10.0 shifted the UV/VIS absorption spectra, resulting in a colour change from yellow to red. The findings of this study have showcased the potential of combining GSE and citric acid to enhance the functionality and bioactivity of alginate films for applications in smart food packaging.

MicroRNAs (miRNAs) regulate plant growth and development and their responses to biotic and abiotic stresses. Although extensive studies show that miR159 family members regulate leaf and flower development in Arabidopsis thaliana, the roles of miRNAs in soybean (Glycine max) are poorly understood. Here, we identified six MIR159 genes in soybean, MIR159aMIR159f, and investigate their expression patterns in plants under low-phosphorus (low-P), NaCl, or abscisic acid (ABA) treatments. In soybean leaves, MIR159e and MIR159f expression was induced by low-P treatment, while in roots, MIR159b, MIR159c, MIR159e, and MIR159f expression was upregulated. In flowers, low-P led to upregulation of MIR159a, MIR159b, MIR159c, and MIR159f, but downregulation of MIR159d and MIR159e. In soybean nodules, MIR159b was upregulated but MIR159a, MIR159c, and MIR159d was downregulated under P deficiency. NaCl treatment induced MIR159a, MIR159b, MIR159c, and MIR159e expression in leaves, and MIR159aMIR159f expression in roots. ABA treatment upregulated MIR159a, MIR159b, and MIR159c but downregulated MIR159d, MIR159e, and MIR159f in leaves. These results suggest that miR159 family members function in plant abiotic stress responses. Moreover, total P content in leaves was significantly lower in plants overexpressing MIR159e than in the wild type, suggesting that miR159e may regulate P absorption and transport in soybean.

Cancer is a catchall term that refers to a collection of more than one chronic disease that can adversely affect the body, including the organs of the body. These diseases can be grouped together under the umbrella term "cancer." Cancer is a catch-all term that is used to refer to a number of different diseases. During the process of looking for new chemical entities, it was found that certain compounds with a basic nucleus of benzoic acid (BA) exhibit a remarkable anticancer potential. This was discovered while the researchers were looking for new chemical entities. In the sixteenth century, the aromatic chemical known as BA, which is also known as an aromatic carboxylic acid, was discovered. BA is also referred to as an aromatic carboxylic acid. When it comes to the chemical synthesis of a wide range of different active molecules, the utilization of a sizeable quantity of BA as a raw material is absolutely necessary. In addition to being present in a variety of other naturally occurring compounds, the BA moiety is the component that is responsible for the activity of the naturally occurring compounds vanillin, gallic acid, and syringic acid. In the synthesis of a wide variety of synthetic bioactive molecules, the BA scaffold is utilized as a building block. The drugs furosemide, bumetanide, benzocaine, tetracaine, and bexarotene are all examples of molecules that fall into this category. The scope of this review article allows for the discussion of a number of noteworthy and recent achievements of BA derivatives in terms of their effectiveness against cancer.

Pozol is a Mexican beverage prepared from fermented nixtamalized maize dough. To contribute to understanding its complex microbial ecology, the effect of inoculating on MRS-starch pure and mixed cultures of amylolytic Sii-25124 and non-amylolytic W. confusa 17, isolated from pozol, were studied on their interactions and fermentation parameters. These were compared with L. plantarum A6, an amylolytic strain isolated from cassava. Microbial growth, kinetic parameters, amylolytic activity, lactic acid production, and hydrolysis products from starch fermentation were measured. The population dynamics were followed by qPCR. L. plantarum A6 showed higher enzymatic activity, lactic acid, biomass production, and kinetic parameters than pozol LAB in pure cultures. Mixed culture of each pozol LAB with L. plantarum A6 showed a significant decrease in amylolytic activity, lactic acid yield, specific growth rate, and specific rate of amylase production. The interaction between Sii-25124 and W. confusa 17 increased the global maximum specific growth rate (µ), the lactic acid yield from starch (Ylac/s), lactic acid yield from biomass (Ylac/x), and specific rate of lactic acid production (qlac) by 15, 30, 30, and 40%, respectively compared with the pure culture of Sii-25124. Interactions between the two strains are essential for this fermentation.

Cationised hemp cellulose was prepared by etherification with two quaternary ammonium salts: 3-chloro-2-hydroxypropyl trimethyl ammonium chloride (CHPTAC) and glycidyltrimethylammonium chloride (GTMAC) and examined for (i) the efficiency of Cr(VI) removal under acid mine-drainage (AMD) conditions, and (ii) antibacterial activity. Adsorbents were characterised by electron microscopy, Fourier transform infrared (FTIR), CP-MAS ¹³C nuclear magnetic resonance (NMR) spectroscopy, elemental composition and surface charge. FTIR and solid state ¹³C NMR confirmed the introduction of quaternary ammonium moieties on cellulose. ¹³C NMR also showed that cationisation decreased the degree of crystallisation and lateral dimensions of cellulose fibrils. Nevertheless, 47 % - 72% of Cr(VI) ions were removed from solutions at pH 4, by 0.1 g of CHPTAC and GTMAC-cationised cellulose, respectively. Adsorption kinetics followed the pseudo-second order model and isotherms were best described by the Freundlich and Dubinin-Radushkevich models. When GTMAC-modified cellulose was applied to AMD contaminated water (pH 2.7), however, Cr(VI) uptake removal decreased to 22% likely due to competition from Al and Fe ions. Nevertheless, cationised materials displayed considerable antibacterial effects, reducing the viability of Escherichia coli by up to 45 % after just 3 hours of exposure. Together, these results suggest that cationised cellulose can be applied in the treatment of Cr(VI)-contaminated mine water particularly if pre-treatments to reduce Fe and Al concentrations are applied.

Aflatoxin biosynthesis is correlated with oxidative stress and is proposed to function as a secondary defense mechanism to redundant intracellular reactive oxygen species (ROS). We find that the antioxidant gallic acid inhibits aflatoxin formation and growth in A. flavus in a dose-dependent manner. Global expression analysis (RNA-Seq) of gallic acid treated A. flavus showed that 0.8% (w/v) gallic acid revealed two possible routes of aflatoxin inhibition. Gallic acid significantly inhibited the expression of farB, encoding a transcription factor that participates in peroxisomal fatty acid β oxidation, a fundamental contributor to aflatoxin production. Secondly, the carbon repression regulator encoding gene creA was significantly down regulated by gallic acid treatment. CreA is necessary for aflatoxin synthesis and aflatoxin biosynthesis genes were significantly downregulated in DcreA mutants. In addition, the results of antioxidant enzyme activities and the lipid oxidation levels coupled with RNA-Seq data of antioxidant genes indicated that gallic acid may reduce oxidative stress through the glutathione- and thioredoxin-dependent systems in A. flavus.

Fatty acids play a major role in determining membrane biophysical properties. Staphylococcus aureus produces branched-chain fatty acids (BCFAs) and straight-chain fatty acids (SCFAs), and can incorporate exogenous SCFAs and straight-chain unsaturated fatty acids (SCUFAs). Many S. aureus strains produce the triterpenoid pigment staphyloxanthin, and the balance of BCFAs, SCFAs and staphyloxanthin determines membrane fluidity. Here, we investigated the relationship of fatty acid and carotenoid production in S. aureus using a pigmented strain (Pig1), its carotenoid-deficient mutant (Pig1ΔcrtM) and the naturally non-pigmented Staphylococcus argenteus that lacks carotenoid biosynthesis genes and is closely related to S. aureus. Fatty acid compositions in all strains were similar under a given condition indicating that staphyloxanthin does not influence fatty acid composition. Strain Pig1 had decreased membrane fluidity as measured by fluorescence anisotropy than the other strains under all conditions indicating that staphyloxanthin helps maintain membrane rigidity. We could find no evidence for correlation of expression of crtM and fatty acid biosynthesis genes. Supplementation of medium with glucose increased SCFA production and decreased BCFA and staphyloxanthin production, whereas acetate-supplementation also decreased BCFAs but increased staphyloxanthin production. We believe that staphyloxanthin levels are influenced more through metabolic regulation than responding to fatty acids incorporated into the membrane.

Flower bud formation and flowering in chrysanthemum occur under short day conditions (SD), but the molecular basis for the switch to reproductive growth is less well understood than in model plants. Here, a spontaneous mutant able to flower under long days is described. In an attempt to reveal the pathway(s) involved in the formation of flower buds under contrasting daylengths, transcriptome sequencing was carried out in plants grown both under SD and under long day conditions (LD). A number of differentially transcribed genes involved in the various known flowering pathways were identified. Both circadian clock genes and CmFTL3 were up-regulated under SD, thereby inducing floral bud formation and flowering. The gibberellin (GA) signalling pathway-related genes GA20ox and GID1 were up-regulated in the mutant under LD, while the catabolic gene GA2ox and GAI was down-regulated, thereby inducing the transcription of CmFTL1, SOC1 and LFY. The GA content of the leaf was higher in the mutant than in the wild type under LD. When treated with GA, the mutant flowered earlier under both SD and LD, but there was no other detectable phenotype difference between the two lines. The indication was that the photoperiod pathway majorly regulates flower bud formation and flowering time in chrysanthemum under SD. GA signalling pathway only plays a subsidiary role for flowering. However, the GA signalling pathway predominated for flowering under LD.

We evaluated the mono- and combination-therapy effects of valproic acid (VPA) and doxorubicin (DOX) in hepatocellular carcinoma (HCC) and identified a specific and efficient, synergistic anti-proliferative effect of the VPA and DOX combination in HCC cells, especially HepG2 cells; this effect was not apparent in MIHA cells, a normal hepatocyte cell line. The calculation of the coefficient of drug interaction confirmed the significant synergistic effect of the combination treatment. Concurrently, the synergistic apoptotic cell death caused by the VPA and DOX combination treatment was confirmed by Hoechst nuclear staining and western blot analysis of caspase-3 and poly (ADP-ribose) polymerase (PARP) activation. Co-treatment with VPA and DOX enhanced reactive oxygen species (ROS) generation and autophagy, which were clearly attenuated by ROS and autophagy inhibitors, respectively. Furthermore, as an indication of the mechanism underlying the synergistic effect, we observed that DOX internalization, which was induced in the VPA and DOX combination-treated group, occurred via by the caveolae-mediated endocytosis pathway. Taken together, our study uncovered the potential effect of the VPA and DOX combination treatment with regard to cell death, including induction of cellular ROS, autophagy, and the caveolae-mediated endocytosis pathway. Therefore, these results present novel implications in drug delivery research for the treatment of HCC.

Increasing efforts have been devoted to promoting sustainable demolition waste management (DWM) from a life cycle-thinking perspective. To this end, facilitating sustainability-oriented de-cision-making for DWM planning requires a sustainability assessment framework for assessing multifaceted criteria. This study develops a BIM-based DWM sustainability assessment ap-proach to facilitate the life cycle assessment (LCA) and decision-making by coupling the enriched IFC model with hybrid Multi-Criteria Decision-Aiding (MCDA) methods using Dynamo visual scripting. To streamline the data-intensive LCA process, this study enriched the BIM properties and accommodated them into the LCA data template to enhance data interoperability, thus achieving seamless data transfer. Moreover, hybrid MCDA methods are integrated into the deci-sion-making workflow for DWM scenario ranking. A pilot study is employed to verify the ap-plicability of the decision-aiding framework. The results unveil that the sustainability score ascended with the recycling rate. The optimal DWM alternative with the highest recycling rate yields the highest sustainability score at 91.63. Conversely, a DWM alternative reflecting the ‘status quo’ in China’s recycling industry has the lowest score at 8.37, significantly lower than the baseline scenario with a 50% recycling rate. It is worth noting that the ‘growth curve’ of the sustainability score continuously flattens as the target recycling rate escalates. The increment in recycling rate from the “Australian standard” scenario to the optimal scenario is 18.4%, while the sustainability score merely increases by 2.3%, signal-ling that the former scenario arrived at an optimum point for maximising the cost-efficiency of DWM under the predefined framework and contexts.

Link prediction is a significant field in network science, which focuses on predicting the probability of the existence or formation of a link between nodes in a social network based on currently observed connections. The effectiveness of traditional algorithms can vary depending on the type of network, making some methods more suitable than others for specific scenarios. Recently, several efficient link prediction algorithms have been developed, demonstrating robust results in both prediction accuracy and interpretability. However, existing research has not clearly established the relationship between network characteristics and link creation mechanisms for community influence analysis and anomaly detection. The ability to predict complex networks with diverse features still requires further investigation. In light of this, we introduce a novel framework designed to combine the best features of different link prediction algorithms when applied to the network, with the aim of achieving more reliable predictions about how networks will evolve. According to the proposed framework, we first focus on the feature extraction stage. During this phase, we systematically identify and extract a comprehensive set of features from the network before moving onto the classification phase. Here, we utilize state-of-the-art ensemble learning models to assess and classify potential links within the network. By training our machine learning models on the extracted features, we can effectively predict whether a particular link is likely to form (positive link) or unlikely to form (negative link). The ML models were trained and evaluated using two datasets: Twitch and Facebook. Results: Additionally, we assessed their performance on these datasets by conducting specific preprocessing and hyperparameter tuning steps. The final prediction model achieves AUC values between 94% and 99.3%. This research contributes significantly to efforts aimed at enhancing link prediction in dynamic socisal network contexts, providing valuable insights into the effectiveness of different ML algorithms in predicting future connections and enhancing our understanding of network dynamics.

Technology-based approaches for upper limb (UL) motor rehabilitation after stroke are designed mostly for severely affected patients to increase their recovery chances. However, the available randomised controlled trials (RCTs) focused on efficacy of technology-based interventions often include patients with a wide range of motor impairment. This scoping review aims at overviewing the actual severity of stroke patients enrolled in RCTs which claim to specifically address UL severe motor impairment. The literature search was conducted on Scopus and PubMed databases and included articles from 2008 to May 2024, specifically RCTs investigating the impact of technology-based interventions on UL motor functional recovery after stroke. Forty-eight studies were selected. They showed that upon patients’ enrolment the values of the UL Fugl-Meyer Assessment and Action Research Arm Test covered the whole range of both scales, thus revealing the non-selective inclusion of severe impaired patients. Heterogeneity in terms of numerosity, characteristics of enrolled patients, trial design, implementation, and reporting were present across studies. No clear difference in the severity of the included patients according to the intervention type was found. Patient stratification upon enrolment is crucial to best direct resources to those patients who will benefit the most from a given technology-assisted approach (personalised rehabilitation).

This study outlines a 3-step production process for Ti-TiC Metal Matrix Composite (MMC) employing powder Mechanical Blending, Laser Powder Bed Fusion (LPBF), and a heat treatment. A TiC fraction of more than 20 vol% was formed in-situ through the reaction of titanium with carbon during the LPBF process. The manufactured MMC pieces showed a record stiffness and fracture strain combination. The LPBF energy density impacted strongly porosity type. The as-built microstructure displayed an homogeneous distribution of sub-stoichiometric TiC dendrites which were fully converted into equiaxed TiC grains during the heat treatment. The TiC C/Ti ratio was found to be close to 0.5, resulting in an effective reinforcement content nearly twice the one expected for stoichiometric TiC, leading to stronger reinforcement. The mechanical analysis revealed a Young’s modulus of up to 149 GPa and an ultimate tensile strength of up to 770 MPa, indicating a 27% and 34% improvement, respectively, compared to commercially pure Titanium produced by LPBF and heat treated in the same conditions. A fracture strain of up to 2.8% was achieved. The combination of in-situ formation of defect-free TiC reinforcement and subsequent heat treatment enables to reach an exceptional ductility, considering the 20 vol% reinforcement content.

This study addresses the critical challenge of Speech Enhancement (SE) in noisy environments, where the deployment of Deep Neural Networksolutions on microcontrollers is hindered by their extensive computational demands. Focusing on this gap, our research introduces a novel SE method optimized for MCUs, employing a 2-layer GRU model that capitalizes on perceptual speech properties and innovative training methodologies. By incorporating self-reference signals and a dual strategy of compression and recovery based on the Mel scale, we develop an efficient model tailored for low-latency applications. Our GRU-2L-128 model demonstrates a significant reduction in size and computational requirements, achieving a 14.2× decrease in model size and a 409.1× reduction in operations compared to traditional DNN methods like DCCRN, without compromising performance. This advancement offers a promising solution for enhancing speech intelligibility in resource-constrained devices, marking a pivotal step in SE research and application.

A compact Mach-zehnder interferometer with a novel design of directional couplers and a phase shifter has been presented as a thermo-optical sensor. With the aim of reducing device size to micro and nano dimension silicon-on-insulator technology was employed. That allowed miniaturization of device size through the reduction of its cross sectional area to 0.066 µm² and the radius of curvature of both the arms of the directional coupler and S-bends of the phase shifter to 5 µm and C-bends to 3 µm. These nano size device dimensions made it possible to reduce the coupling gap to 0.2 µm, which resulted in a significant reduction in the coupling length. The device geometry and its performance characteristics were analyzed and optimized using coupled mode analysis and finite difference time domain simulation tools, respectively. The wavelength dependent transmission loss of the device was measured at different temperature to verify and validate its performance characteristics. Tested devices showed a remarkable temperature dependent transmission characteristic offering significant changes in transmission loss band – with as low as 0.45 ⁰C change in substrate temperature. The extinction ratio and the free spectral range of the device were 26 dB and 0.26 nm respectively in the wavelength range of 1549.5 nm – 1550.5 nm. These results imply that the devices presented here can be used as compact and highly sensitive thermal sensors and optical switches.

This work presents the study of a reproducible acoustic emission method based on the launching of a metallic sphere and low-cost piezoelectric diaphragm. For this purpose, tests were first conducted on a carbon fiber-reinforced polymer structure, and then on an aluminum structure for comparative analysis. The Pencil Lead Break (PLB) tests were also conducted for comparisons with the proposed method. Different launching heights and elastic deformations of the structures were investigated. The results show higher repeatability for the sphere impact method, as the PLB is more affected by human inaccuracy, and it was also effective in damage detection.

Biodiesel, a potent replacement for petroleum diesel, is derived from fatty acids in biomass through transesterification, which is renewable, non-toxic, and biodegradable and is a powerful replacement for petroleum diesel. Lewis acid has been proven effective for esterification and transesterification. The Lewis base enhances the electrophilic and nucleophilic properties of the molecules that bind to it, leading to the remarkable versatility in the Lewis base catalytic reaction. Many studies have shown that Lewis acid/base catalyzed in-situ transesterification is a fast and environmentally friendly method for producing biodiesel. The utilization of Lewis acid-base sites to catalyze transesterification has been shown to enhance their efficiency and utilization of ac-id-base active sites. This review explores biodiesel production by different catalysts using Lewis acid-base sites, the conditions for catalytic transesterification, the effects of different reaction parameters on biodiesel production, and biodiesel production process.

Infections are a common post-operative ailment for patients who have received a dental implant or device and can be attributed to biofilm formation in tissue or on the implant. Many current solutions for oral hygiene have side effects and affect the natural oral microbiome. 2-heptylcyclopropane-1-carboxylic acid (2CP) is a medium-chain fatty acid and synthetic diffusible signaling factor that can prevent and disperse biofilm. The purpose of this work was to evaluate an immersion strategy for coating hydroxyapatite (HAp) with 2CP to prevent biofilm attachment on and around natural teeth and dental implants. The release profile of 2CP-loaded and 2CP+oral rinse-loaded HAp coupons (n=6) was assessed by a 3-day exposure to phosphate buffered saline (PBS). Antimicrobial properties against Porphyromonas gingivalis and cytocompatibility of 2CP-loaded HAp coupons (n=4) were also assessed alone and in combination with 0.12% chlorhexidine gluconate oral rinse. The majority of 2CP is released by 12 hours. 2CP, oral rinse, and 2CP+oral rinse significantly reduced P. gingivalis viability, though direct contact assay demonstrates a significant reduction in Saos-2 viability for oral rinse and 2CP+oral rinse coupons. Immersion or rinsing hydroxyapatite with 2CP could inhibit biofilm-associated dental infections and prevent further complications including caries, gingivitis, and peri-implantitis.

This study investigates the implementation of equipment to obtain pyroligneous acid as an alternative to control aphids in mandarin cultivation on the El Arrayanal farm, Monte Olivo parish, Carchi province, Ecuador. Derived from mandarin pruning biomass using a dry distillation pilot oven, pyroligneous acid is an ecological option compared to synthetic phytosanitary products, with less impact on the environment and human health. Using a DBCA design, different concentrations of pyroligneous acid (250 ml, 500 ml, 750 ml, and 1000 ml) applied to immature shoots affected by aphids were analyzed. The 1000 ml concentration achieved 98% control of the pest. Analysis by Gas Chromatography and Mass Spectrometry (GC-MSD) and Total Polyphenols confirmed the effectiveness of pyroligneous acid. The results of the study, carried out in the research and linkage laboratories of the State University of Bolívar, Guaranda, Ecuador, demonstrated significant differences between the doses applied (p-value <0.005), with greater control in the treatment of 1000 ml of acid pyroleño compared to the 250 ml, 500 ml and 750 ml treatments. This pyroligneous acid has multiple uses in organic agriculture as a bioherbicide, biofungicide, biorepellent and foliar and root biostimulant, representing an alternative to obtain sustainable organic products. Despite operational limitations, local pyrolysis technology can be optimized to increase production, positioning pyroligneous acid as a viable and sustainable alternative in organic agriculture, promoting efficient waste management and reducing the use of chemicals.

This study deals with the preparation of adsorbents from a commercial xerogel by chemically modifying its surface with concentrated mineral acids and alkali metal chlorides, their physicochemical characterization, and their use as adsorbents for gallic acid in aqueous solution. The prepared adsorbents have a high specific surface area (347-563 m2 g-1), better pore development for samples treated with alkali metal chlorides than with mineral acids and are more acidic than the initial xerogel (p.z.c range 2.49-6.87 vs. 7.20). The adsorption properties of the commercial xerogel improved over a wide range of pH and temperature. The experimental results indicate that the adsorption process is thermodynamically favored.

Melittin, a natural antimicrobial peptide, displays a broad-spectrum antimicrobial activity, which has caused increasing attention as a potential antibiotic alternative. However, melittin has not been used widely at present due to its high hemolysis and low proteolytic stability. In this study, N-terminal fatty acid was conjugated to melittin to develop new melittin-derived lipopep-tides (MDLs) for improving the limitation of melittin. Our results showed that, the antimicrobial activity of MDLs was increased by 2 to 16 times compared with native melittin, and the stability of these MDLs against trypsin and pepsin degradation was increased by 50 to 80%. Besides, the hemolytic of the MDLs decreased when the length of the carbon chain of fatty acids exceeded 10. Among them, the newly designed analog Mel-C8 showed optimal antimicrobial activity and protease stability. The antimicrobial mechanism studied revealed that the MDLs showed a rapid bactericidal effect by interacting with LPS or LTA and penetrating the bacterial cell membrane. In conclusion, we designed and synthesized a new class of MDLs with potent antimicrobial activity, high proteolytic stability, and low hemolysis through N-terminal fatty acid conjugation.

Pt-coated Ni layer supported on Ni foam catalyst (denoted PtNi/Nifoam) was investigated for the oxidation of the formic acid (FAO) in acidic media. The prepared PtNi/Ni foam catalyst was studied as a function of the formic acid (FA) concentration at bare Pt and PtNi/Nifoam catalysts. The catalytic activity of the PtNi/Nifoam catalysts, studied on the basis of the ratio of the direct and indirect current peaks (jd)/(jnd) for the FAO reaction, showed values about 10 times higher compared to those on bare Pt, particularly at a low formic acid concentrations, reflecting the superiority of the former catalysts for the oxidation of FA to CO2. Ni foams provide a large surface area for the FOR while synergistic effects between Pt nanoparticles and Ni-oxy species layer on Ni foams contribute significantly to the enhanced oxidation of FA via the direct pathway, making it almost equal to the indirect pathway, particularly at low formic acid concentrations.

This work aimed at producing lactic acid (LA) from sugarcane bagasse after steam explosion at 195 ºC for 7.5 and 15 min. Enzymatic hydrolysis was carried out with Novozymes’ Cellic CTec3 and/or Cellic HTec3, whereas fermentation was performed with Bacillus coagulans DSM2314. Water-washing of pretreated solids before enzymatic hydrolysis improved both hydrolysis and fermentation yields. The presence of xylo-oligosaccharides (XOS) in substrate hydrolysates reduced hydrolysis efficiency, but their effect on fermentation was negligible. The presence of fermentation inhibitors in C5 streams was circumvented by adsorption on activated carbon powder with no detectable sugar losses. High carbohydrates-to-LA conversions (Yp/s) of 0.88 g·g-1 were obtained from enzymatic hydrolysates of water-washed steam-exploded materials that were produced at 195°C, 7.5 min and the use of centrifuged-but-never-washed pretreated solids decreased Yp/s by 16%. However, when the detoxified C5 stream was added at a 10% ratio, Yp/s was raised to 0.93 g·g-1 for an LA productivity of 2.55 g·L-1·h-1. Doubling the pretreatment time caused a decrease in Yp/s to 0.78 g·g-1, but LA productivity was the highest (3.20 g·L-1·h-1). For pretreatment at 195°C for 7.5 min, elimination of water washing seemed feasible, but the use of longer pretreatment times made it mandatory to eliminate fermentation inhibitors.

High-performance electromagnetic interference (EMI) shielding materials with ultralow density and environment friendly properties are greatly demanded to address electromagnetic radiation pollution. Herein, carbon nanotubes/polylactic acid (CNTs/PLA) materials with different CNTs contents, which exhibit characteristics of light weight, environmental protection and good chemical stability, are fabricated by 3D printing technology, where CNTs are evenly distributed and bind well with PLA. The performances of 3D printed CNTs/PLA composite are improved compared to pure 3D printed PLA composite, which include mechanical properties, conductive behaviors and electromagnetic interference (EMI) shielding. The EMI shielding effectiveness (SE) of CNTs/PLA composite could be improved when the contents of CNTs increase. When it reaches 15 wt%, the EMI SE of 3D printed CNTs/PLA composite could get up to 47.1 dB, which shields 99.998% of electromagnetic energy. Meanwhile, the EMI shielding mechanism of 3D printed CNTs/PLA composite is mainly of absorption loss, and it generally accounted for more than 80% of the total shielding loss. These excellent comprehensive performances endow the 3D printed CNTs/PLA composite with great potential for use in industrial and aerospace area.

Aqueous enzymatic method is a green oil extraction technology with limited industrial application owing to the need for demulsification of the oil body intermediate product. Existing demulsification methods have problems including low demulsification rates and high costs, such that new methods are needed. Free fatty acids produced by lipid hydrolysis can affect the stability of peanut oil body (POB) at a certain concentration. After screening even-carbon fatty acids with carbon chain lengths below ten, caproic acid was selected for demulsification of POB using response surface methodology and a Box–Behnken design. Under the optimal conditions (caproic acid concentration, 0.22%; material-to-liquid ratio, 1:4.7 (w/v); time, 61 min; and temperature, 79 C), a demulsification rate of 97.87% was achieved. Caproic acid not only adjusted the reaction system pH to cause aggregation of the POB interfacial proteins, but also decreased the interfacial tension and viscoelasticity of the interfacial film with increasing caproic acid concentration to realize POB demulsification. Compared with pressed oil and soxhlet-extracted oil, the acid value and peroxide value of caproic acid demulsified oil were increased, while the unsaturated fatty acid content and oxidation induction time were decreased. However, the tocopherol and tocotrienol contents were higher than those of the soxhlet-extracted oil. This study provides a new method for the demulsification of POB.

Manganese sludge, an industrial waste in the ferroalloy industry, contains various components and holds significant importance for sustainable development through its valorization. This study focuses on characterizing a manganese sludge and investigating its behavior during sulfuric acid leaching. The influence of process conditions, including temperature, acid concentration, liquid to solid ratio, and leaching duration, was examined. The results revealed that Mn, Zn, and K are the main leachable components, and their leaching rates increase with increasing temperature, liquid to solid ratio, and time. However, acid concentration requires optimization. High leaching rates of 90% for Mn, 90% for Zn, and 100% for K were achieved. Moreover, it was found that Pb in the sludge is converted to sulfate during the leaching which yields a sulfate concentrate rich in PbSO4. The leaching process for Mn and Zn species appears to follow a second or -third order reaction, and the calculation of rate constants indicated that Mn leaching kinetics are two to five times higher than those for Zn. Thermodynamic calculations were employed to evaluate the main chemical reactions occurring during leaching.

Thermoplastic molded regenerated silk was proposed as structural material in tissue engineering applications, mainly for application in bone. The protocol allows to obtain a compact non-porous material with a compression modulus in the order of a Giga Pascal starting from silk fibroin by compressing a silk fibroin lyophilized sponge of powder in mold at temperature higher than the glass transition temperature (Tg). The main purpose of the produced resin was the osteofixation and other structural applications in which the lack of porosity was not an issue. In this work, we introduced the use of citric acid in the thermoplastic molding protocol of SF to obtain a porosity inside the structural material. In addition to the previously developed protocols the addition of citric acid allowed us to obtain a structural material. The CA powder during the compression acted as a template for the pore formation. In addition, the CA was able to effectively crosslink the SF chain improving the mechanical strength. This effect was proved both evaluating the compression modulus and by studying the spectra obtained by Fourier infrared spectroscopy (FTIR). This protocol may be applied in the near future to the production of a structural bone scaffold.

Biochar is a carbon allotrope obtained by pyrolysis of biomass, usually agro-waste. Owing to the demand for sustainable development, biochar is continuously raising much hope in the scientific community. However, in order to impart it with new properties, its modification is required, either in situ during pyrolysis, or after the carbonization process. Herein, we propose a new direct approach to obtain bimetallic copper/nickel nanoparticle-loaded on olive stone biochar. The bimetallic-coated biochar and the reference materials bare biochar, copper-loaded and nickel-loaded biochar were prepared at 400 °C under a stream of dinitrogen from olive pit powder particles impregnated first with citric acid (CA), and then with copper and nickel nitrates. We have employed citric acid in the process in order to check its effect on the structural and textural properties of biochar supporting the metallic nanoparticles. Surprisingly, citric acid induced the formation of agglomerated or even raspberry-shaped, bimetallic copper/nickel nanoparticles. Large 450-500 nm-sized agglomerates of ~80 nm bimetallic CuNi NPs were noted for B-CA@CuNi. Interestingly, for biochar material prepared with initial Cu/Ni=10 molar ratio (B-CA@CuNi10/1), the bimetallic NPs formed unusual nano-raspberries (1748 nm in size) which are agglomerates of individual 10-20 nm-sized CuNi10/1 nanoparticles. The B-CA@CuNi and reference materials were characterized by Raman spectroscopy, scanning electron microscopy (SEM)/energy-dispersive X-ray spectroscopy (EDX), X-ray diffraction (XRD) and magnetometry. The B-CA@CuNi and B-CA@Ni materials could be attracted efficiently with a magnet, but not B-CA@CuNi10/1 due to a low nickel loading. B-CA@CuNi was tested as a catalyst for the degradation of methyl orange (MO). Discoloration was noted within 10 min, much faster than a similar material prepared in the absence of CA. B-CA@CuNi could be recycled at least 3 times with exhibit as fast discoloration catalysis performance. This paper stresses the important role of citric acid in shaping the bimetallic nanoparticles loaded in situ on biochar during the slow pyrolysis process and to enable faster catalysed discoloration of organic dye solution.

Ustilago maydis, member of the Ustilaginaceae family, is a promising host for the production of several metabolites including itaconic acid. This dicarboxylate has great potential as a bio-based building block in the polymer industry, and is of special interest for pharmaceutical applications. Several itaconate overproducing Ustilago strains have been generated by metabolic and morphology engineering. This yielded stabilized unicellular morphology through fuz7 deletion, reduction of by-product formation through deletion of genes responsible for itaconate oxidation and (glyco)lipid production, and the overexpression of the regulator of the itaconate cluster ria1 and the mitochondrial tricarboxylate transporter encoded by mttA from Aspergillus terreus. In this study, itaconate production was further optimized by consolidating these different optimizations into one strain. The combined modifications resulted in itaconic acid production at theoretical maximal yield, which was achieved under biotechnologically relevant fed-batch fermentations with continuous feed.

Lipid-based drugs are emerging as an interesting class of novel anticancer drugs with the potential to target specific cancer cell metabolic pathway linked to their proliferation and invasiveness. In particular, ω−3 polyunsaturated fatty acids (PUFA) derivatives such as epoxides and their bioisosteres have demonstrated the potential to suppress growth and promote apoptosis in triple-negative human breast cancer cells MDA-MB-231. In this study 16-(4’-chloro-3’-trifluorophenyl)carbamoylamino]hexadecanoic acid (ClFPh-CHA), an anticancer lipid derived from ω−3,17,18-epoxyeicosanoic acid, was formulated as a stable nanoemulsion with size around 150 nm and narrow droplet size distribution (PDI<0.200) through phase-inversion emulsification process followed by high pressure homogenization in view of an oral administration. The ClFPh-CHA-loaded nanoemulsions were able to significantly decrease the relative tumor volume in mice bearing an intramammary tumor xenograft at all doses tested (2.5, 10 and 40 mg/kg) after 32 days of daily oral administration. Furthermore, absolute tumor weight was decreased to 50% of untreated control at 10 and 40 mg/kg, while intraperitoneal administration could achieve a significant reduction only at the highest dose of 40 mg/kg. Results suggest that oral administration of ClFPh-CHA formulated as a nanoemulsion has a sufficient bioavailability to provide an anticancer effect in mice and that the activity is at least equal if not superior to that obtained by a conventional parenteral administration of equivalent doses of the same drug.

The aim of this study (first analytical approach) was to obtain data on the fatty acid composition of gluten-free foods (bakery products) for celiac people. The study included 35 different products (snacks, biscuits, bakery products, pasta, flours, etc.) from several manufacturers. After extraction and esterification, the fatty acid content was determined by GC-MS. The monounsaturated fatty acids (MUFAs) are the major constitutes (57%) of the fatty acids pool followed by saturated fatty acids (SFAs) (30%) and polyunsaturated fatty acid (13%). Only fifteen, of the thirty-five gluten free samples analyzed, provide adequate energy intake, while in eleven samples, saturated fatty acids take more energy than that recommended by EFSA. It has emerged that local producers generally use the finest raw materials (olive oil, etc.) compared to the industries which, as has been pointed out, in many cases use palm and palm kernel oils although gluten free commercial products are high added value foods, expensive and intended for a particularly sensitive public.

Abstract: Measures to counteract AMD generation need to start at the mineral surface, inhibiting mineral-oxidizing, acidophilic microbes. Laboratory and long-term field tests with pyrite-containing mining wastes, where Carbonaceous Phosphate Mining Waste (CPMW) was added, resulted in low acidity, and near neutral drainage. The effect was reproducible, nd confirmed by several independent research groups. This was shown to involve an organic coating, likely a biofilm. The biofilm formation was confirmed when CPMW was added to lignite coal waste with an initial pH of 1. Forty five days after the addition, the coal waste was dominated by heterotrophic microorganisms in biofilms. A review of the scientific literature supports that CPMW has physical and chemical characteristics which are capable of inducing a strong inhibitory effect on sulphide oxidation by forming an organic coating over the mineral surface. CPMW characteristics appear to provide the cornerstone of a new technology for the reduction of sulphide oxidation in mine wastes. An hypothesis for testing this technology is presented which could result in an economical and sustainable approach to mine waste and water management.

Abnormal Tau phosphorylation and aggregation into neuronal paired helical filaments and neurofibrillary tangles cause tauopathies, a class of neurodegenerative diseases, that include Alzheimer’s disease, frontotemporal dementia and parkinsonism linked to chromosome 17, progressive supranuclear palsy, Pick's disease, and corticobasal degeneration. Glycogen synthase kinase-3β (GSK-3β) is the most critical kinase to phosphorylate Tau. We have developed the linoleic acid derivative 8-[2-(2-pentyl-cyclopropylmethyl)-cyclopropyl]-octanoic acid (DCP-LA), with cyclopropane rings instead of cis-double bonds, as an anti-dementia drug. DCP-LA serves as a selective activator of PKCε and a potent inhibitor of protein tyrosine phosphatase 1B (PTP1B). DCP-LA prevents Tau phosphorylation due to PKCε-mediated direct inactivation of GSK-3β, to PKCε/Akt-mediated inactivation of GSK-3β, and to receptor tyrosine kinase-mediated inactivation of GSK-3β in association with PTP1B inhibition. DCP-LA targeting GSK-3β, thus, could become a valid drug for treatment of tauopathies.

In the majority of children with growth hormone (GH) deficiency (GHD), normal GH secretion may occur before the attainment of final height. The aim of the study was to assess the incidence of persistent and transient GHD and the effectiveness of recombined human GH (rhGH) therapy in children with isolated idiopathic GHD, with respect to the moment of therapy withdrawal and according to different diagnostic criteria of GHD. Analysis included 260 patients (173 boys, 87 girls) with isolated idiopathic GHD who completed rhGH therapy and have reassessed GH and IGF-1 secretion. The incidence of transient GHD with respect to different pre- and post-treatment criteria was compared together with assessment of GH therapy effectiveness. Incidence of transient GHD, even with respect to pediatric criteria was very high. Normal GH secretion occurred before the attainment of near-final height. Application of more restricted criteria decreased the number of children diagnosed with GHD but not the incidence of transient GHD among them. Poor response to GH therapy was observed mainly in patients with normal IGF-1 before treatment, suggesting that diagnosis of GHD may be false positive. Further efforts should be made to avoid overdiagnosis GHD and overtreatment of the patients.

Background: The aim of this study was to investigate a series of complete blood cell count – based biomarkers of systemic inflammation as predictors of clinical outcomes in patients who underwent first-line chemoimmunotherapy for advanced NSCLC. Methods: Consecutive patients with pathologically diagnosed stage III/IV NSCLC who underwent first-line chemoimmunotherapy were retrospectively enrolled. The clinical outcomes used for biomarker evaluation were Objective Response Rate (ORR) and Overall Survival (OS). Results: Non-responders had significantly higher values of neutrophil to lymphocyte ratio (NLR, median: 5.36; IQR: 2.78–10.82 vs. 3.31; IQR: 2.15–4.12, p = 0.019), neutrophil to monocyte ratio (NMR, median: 14.00; IQR: 8.82–21.20 vs. 9.20; IQR: 7.45–11.20, p = 0.013), and systemic inflammation index (SII, median: 1,395; IQR: 929–3,334 vs. 945; IQR: 552–1,373, p = 0.025), but only NLR and NMR remained independently related with clinical response in multivariate logistic regression. In univariate analysis white blood cells (OR:1.2202; 95% CI: 1.0339 - 1.4400, p=0.019), neutrophils (OR:1.2916; 95% CI: 1.0692 - 1.5604, p=0.008), NLR (OR:1.3601: 95% CI: 1.0949 - 1.6896, p=0.005) and NMR (OR:1.2159; 95% CI: 1.00396 - 1.4221, p=0.015) were significantly associated with survival; Cox regression models confirmed that neutrophils, NLR and MLR were independently associated with survival; NLR at a cut-off value of 4.0 showed the better AUC (0.749) in predicting survival. Conclusions: Baseline complete blood cell count biomarkers, especially the NLR, can predict clinical outcomes in patients with advanced NSCLC treated with first-line chemoimmunotherapy.

Tidal energy, with its potential to provide a consistent energy output and reduce carbon emis-sions, has garnered significant interest. This study, which is the first to evaluate the performance of tidal turbines in seawater conditions involving sand particles, presents a novel approach. A slurry rig was developed to examine composite materials, and a glass fibre reinforcement poly-meric material was tested over a range of particle size, velocity, impact angle, and exposure time. The results, which show significant changes in the mass loss materials as a function of these variables, have profound implications for the design and performance of tidal turbines. The study also utilized a scanning electron microscope (SEM) and depth profiling analysis, and erosion maps were generated to demonstrate the changes in erosion mechanisms. These tools can be used to optimize such materials in tidal turbine conditions.

The results of studying the effect of particles of few-layer graphene (FLG) synthesized by self-propagating high-temperature synthesis (SHS) on the complex of strength and thermo physical properties of polymer composite products obtained by DLP 3D printing are presented. It has been discovered to achieve an increase in thermo physical and strength parameters of polymers modified by FLG compared with samples made on the unmodified base resin. This result was achieved due to low defectiveness, namely the absence of Stone-Wales defects in the structure of FLG due to the homogeneous distribution of FLG over the volume of the polymer in the form of highly dispersed aggregates. It was possible to increase hardness by 120 %, bending strength by 102 %, Charpy impact strength by 205 %, and thermal conductivity at 25 °C by 572 % at concentrations of few-layer graphene of no more than 2 wt. %.

Consumer IoT (CIoT) manufacturers seek customer feedback to enhance their products and services, creating a smart ecosystem like a smart home. Due to security and privacy concerns, Blockchain-based federated learning (BCFL) ecosystems can let CIoT manufacturers update their Machine Learning (ML) model using end-user data. FL uses privacy-preserving ML techniques to forecast customers' needs and consumption habits, and blockchain replaces the centralised aggregator to safeguard the ecosystem. However, Blockchain technology (BCT) struggles with scalability and quick ledger expansion. In BCFL, local model generation and secure aggregation are other issues. This research contributes a novel architecture emphasising Gateway Peer (GWP) in blockchain network to resolve scalability, ledger optimisation and secure model transmission issues. In the architecture we replace the centralised aggregator by the blockchain network, while GWP restricts the number of local transactions to execute in BCN. Considering the security and privacy of FL processes, we have added differential privacy and advanced normalisation techniques to ML processes. The approaches strengthen end-users' cyber security and encourage the adoption of technological innovation standards by service providers. The proposed approach has been tested extensively using a well-respected Stanford Cars dataset. We experimentally demonstrate that the proposed architecture makes the network scalable and optimises the ledger significantly. In addition, the normalisation technique outperforms batch normalisation when features are under DP protection.

This work (in two parts) will review the recently developed predictive modeling methodology called “4th-BERRU-PM” and its applicability to energy systems as exemplified by an illustrative application to the Polyethylene-Reflected Plutonium (acronym: PERP) OECD/NEA reactor physics benchmark. The acronym 4th-BERRU-PM designates the “Fourth-Order Best-Estimate Results with Reduced Uncertainties Predictive Modeling” methodology, which yields best-estimate results with reduced uncertainties for the first fourth-order moments (mean values, covariance, skewness, and kurtosis) of the optimally predicted posterior distribution of model results and calibrated model parameters. The 4th-BERRU-PM uses the Maximum Entropy (MaxEnt) principle to incorporate fourth-order experimental and computational information, including fourth (and higher) order sensitivities of computed model responses to model parameters, thus incorporating, as particular cases, the results previously predicted by the second-order predictive modeling methodology 2nd-BERRU-PM, and vastly generalizing the results produced by extant data assimilation and data adjustment procedures. The 4th-BERRU-PM methodology encompasses the scopes of high-order sensitivity analysis (SA), uncertainty quantification (UQ), data assimilation (DA) and model calibration (MC). The application of the 4th-BERRU-PM methodology to energy systems is illustrated by means of the above-mentioned OECD/NEA reactor physics benchmark, which is modeled using the neutron transport Boltzmann equation involving 21976 imprecisely known parameters, the solution of which is representative of “large-scale computations.” The model result (“response”) of interest is the leakage of neutrons through the outer surface of this spherical benchmark, which can be computed numerically and measured experimentally. Part 1 of this work illustrates the impact of high-order sensitivities, in conjunction with parameter standard deviations of various magnitudes, on the determination of the expected value and variance of the computed response in terms of the first four moments of the distribution of the uncertain model parameters. Part 2 of this work will illustrate the capabilities of the 4th-BERRU-PM methodology for combining computational and experimental information, up to and including forth-order sensitivities and distributional moments, for producing best-estimate values for the predicted responses and model parameters while reducing their accompanying uncertainties.

Strong yet ductile alloys have long been desired for industrial applications to enhance structural reliability. This work produced two (CoCrNi)93.5Al3Ti3C0.5 medium-entropy alloys with exceptional strength-ductility combinations, via short/medium (3 min/30 min)-time annealing after hot-rolling. Three types of intergranular precipitates including MC, M23C6 carbides, and L12 phase were detected in both the samples. Noticeably, the high density of intragranular L12 precipitates were only founded in the medium-time annealed sample but not in another one. Upon inspection of deformed substructure, it was revealed that the plane slip is the dominant deformation mechanism of both the alloys. This is related to the lower stacking fault energy, higher lattice friction induced by C solute, and slip plane softening caused by intragranular dense L12 precipitates. Additionally, we noted that the stacking fault and twinning act as the mediated mechanisms in deformation of the short-time annealed alloy, while only the former in the medium-time annealed one. It is attributed to the higher energy stacking faults and the increased critical twinning stress caused by intragranular dense L12 precipitates that inhibited the twinning tendency. Our present findings provide not only a guidance for optimizing the mechanical properties of high/medium-entropy alloys, but also a fundamental understanding of deformation mechanisms.

Pentadecanoic acid (C15:0) and heptadecanoic acid (C17:0) have been described as dietary biomarkers of dairy-fat consumption with varying degrees of reliability between studies. It remains unclear how the total amount of dietary fat; one of the main confounding factors in these biomarker investigations, affects C15:0 and C17:0 circulating compositions independently to their relative intake. Additionally, it is unknown how changes in the dietary total-fat affects other fatty acids in circulation. Through two dietary studies with different total-fat levels but maintaining individual fatty acid compositions we were able to see how the dietary total-fat affects the fatty acids in circulation. We saw that there was a significant, proportionate, and robust decrease in the endogenous C15:0 levels with an increase in dietary total-fat. However, there was an increase in the circulating C17:0 compositions as the total-fat increased. To conclude, the dietary total-fat content and fat-type have a very complex influence on the relative compositions of circulating fatty acids, which are independent to the actual dietary fatty acid composition. Knowing how to manipulate circulating C15:0 and C17:0 composition is far-reaching in nutritional/pathological research as they highlight a dietary route to attenuate the development of metabolic disease (both by reducing risk and improving prognosis).

The medium-voltage DC (MVDC) technology has gained increasing interests in recent years. Power electronics devices dominate those grids. Accurate simulation of such a grid, with detailed models of switching semiconductors, can quickly became very time-consuming, according to the number of connected devices to be simulated. A simulation approach based on interactions on a continuous time model can be very interesting, especially for developing a system level control model of such a modern MVDC distribution grid. Aim of this paper is to present all the steps required for obtaining a continuous time modelling of a +/- 10 kV MVDC grid case study, including Solid State Transformer (SST) and Modular Multilevel Converter (MMC) based Active Front End (AFE). Additional aim of this paper is to supply an educational content about the use of the continuous time simulation approach, thanks to a detailed description of the various devices modelled into the presented MVDC grid. The results of a certain number of simulation scenarios are eventually presented.

Microscopic vision plays an important role in automated micro-assembly. However, some uncertain factors in the assembly process, such as occlusion and stains can lead to the mistakes of feature extraction. Herein, to solve the problem, the deep learning techniques are introduced into the feature recognition tasks, focusing on the attention mechanism and visualizing CNNs for DL-based microscopic vision. The main contributions are summarized as follows: The CBAM attention mechanism is combined with the YOLOv5 algorithm to improve the accuracy and robustness of feature extraction. The micropart feature occlusion experiment results show that at 70% occlusion degree, YOLOV5-CBAM can reach 97.9% mAP@0.5, which is 4.6% higher than the original one. Visualization analysis of DL-based model is conducted using Grad-CAM to make the decision result more transparent and avoid potential visual detection risks during assembly. The heatmap matching degree between GT area and high-light area is increased by 27.81% on average, which further verify the effectiveness of attention mechanism in micropart feature localization. Additionally, micropart surface stain and droplet quality classification models based on ResNet50 are trained to replace the manual sorting. The visual results are consistent with human eye discernment and judgement, confirming the reliability of parts and droplets sorting.

Background: Over the past two decades, the Copenhagen Psychosocial Questionnaire (COPSOQ) has been established as a valid instrument to measure psychosocial stress at work. Currently, the COPSOQ international network is responsible for monitoring and improving COPSOQ. In 2019, a new questionnaire was published, and the Greek version is now being validated. Methods: The measurement qualities of the Greek COPSOQ III have been explored in accordance with the usual requirements of a validation study as defined by DIN EN ISO 10075-3. A sample of observations from 2,189 participants surveyed with the COPSOQ in Greece was used to validate the current version with appropriate statistical analyses. Exploratory factor analysis was used to assess the statistical relationships for many scales. Results: With its 108 items and 40 scales, the Greek COPSOQ III includes all psychosocial work factors that have been internationally validated and remain compatible with approximately 72% of the COPSOQ III German version content. In addition to the primary results, congruence with widely used theoretical approaches such as the demand-control (−support) model (DCM) or the job demands-resources model (JDR) is generally satisfactory. In summary, our validation study for the Greek COPSOQ III version showed adequate reliability and validity, which is in line with the findings of the COPSOQ III questionnaire from other European countries, and it is also compatible with the validation of the German COPSOQ III (Lincke, 2021). Our regression analysis revealed that 34 psychosocial work factors (34 “context” scales) could adequately predict the scores of the satisfactory and health scales (6 “outcome” scales). The analysis also revealed the top five (5) predictors (context variables) for each of the six (6) “effect” scales (outcome variables). Conclusions: With the launch of COPSOQ III in Greece, current and new workplace psychosocial aspects could be explored. COPSOQ III (GR) is a beneficial instrument for enterprise research and risk assessment.

The application of deep learning algorithms to predict the molecular profiles of various cancers from digital images of hematoxylin and eosin (H&E)-stained slides has been reported in recent years, mainly in gastric and colon cancers. In this study, we investigated the potential use of H&E-stained endometrial cancer slide images to predict the associated mismatch repair (MMR) status. H&E-stained slide images were collected from 127 cases of the primary lesion of endometrial cancer. After digitization using a Nanozoomer virtual slide scanner (Hamamatsu Photonics), we segmented the scanned images into 5,397 tiles of 512 × 512 pixels. The MMR proteins (PMS2, MSH6) were immunohistochemically stained, classified into MMR proficient/deficient, and annotated for each case and tile. We trained several neural networks, including convolutional and attention-based networks, using tiles annotated with the MMR status. Among the tested networks, ResNet50 exhibited the highest area under the receiver operating characteristic curve (AUROC) of 0.91 for predicting the MMR status. The constructed prediction algorithm may be applicable to other molecular profiles and useful for pre-screening before implementing other, more costly genetic profiling tests.

This paper is based on the concept of absolute airspace and its local absolute stationary reference system proposed by the author, on the premise of abandoning space concept and the relativity principle of relativity theory, It is proposed that general relativity and special relativity can be unified into Simple and practical a space-time transformation theory which fully includes other basic physical principles of relativity. And the unified and simple expression of the time transformation effect is proved and deduced. By comparing with the theoretical derivation and checking calculation of Hafele-Keating experiment in an ideal state, It is proved that the expression of time transformation effect proposed in this paper is completely correct. Compared with the theory of relativity, the calculation is simpler and more accurate. The paper also puts forward two checking prediction of physical cases about the time transformation effect, which are left for the capable competent unit or individual to verify in practice.

Accurate forecasting of crop yields holds paramount importance in guiding decision-making processes related to breeding efforts. This study focused on the application of multi-sensor data fusion and machine learning algorithms based on unmanned aerial vehicles (UAVs) in wheat yield prediction. Five machine learning (ML) algorithms namely random forest (RF), partial least squares (PLS), ridge regression (RR), K-Nearest Neighbor (KNN) and eXtreme Gradient Boosting Decision Tree (XGboost) were utilized for multi-sensor data fusion, and three ensemble methods including the second-level ensemble methods (stacking and feature-weighted) and the third-level ensemble method (simple average) for wheat yield prediction. The 270 wheat hybrids were used as planting materials under full and limited irrigation treatments. A cost-effective multi-sensor UAV platform, equipped with red–green–blue (RGB), multispectral (MS), and thermal infrared (TIR) sensors, was utilized to gather remote sensing data. The results revealed that the XGboost algorithm exhibited outstanding performance in multi-sensor data fusion, with the RGB+MS+Texture+TIR combination demonstrating the highest fusion performance (R2=0.660, RMSE= 0.754). Compared with the single ML model, the employment of three ensemble methods significantly enhanced the prediction accuracy of wheat yield. Notably, the third-layer simple average ensemble method demonstrated superior performance (R2 = 0.733, RMSE= 0.668 t ha-1). It significantly outperformed both the second-layer ensemble methods of Stacking (R2= 0.668, RMSE= 0.673 t ha-1) and feature-weighted (R2= 0.667, RMSE= 0.674 t ha-1), thereby exhibiting superior predictive capabilities. This finding demonstrated that the third-layer ensemble method not only augments the predictive ability of the model but also fine-tuned the accuracy of wheat yield prediction through the employment of simple average ensemble learning. Consequently, it offers a novel perspective for crop yield prediction and breeding selection.

Parkinson’s Disease (PD) is a debilitating neurodegenerative disease, causing loss of motor function, and in some instances, cognitive decline and dementia, in those affected. The quality of life can be improved, and disease progression delayed through early interventions, however, current methods of confirming a PD diagnosis are extremely invasive. This prevents their use as a screening tool for the early onset stages of PD. We propose a surface imprinted polymer (SIP) electroimpedance spectroscopy (EIS) biosensor for detecting α-Synuclein (αSyn) and its aggregates, a biomarker that appears in saliva and blood during the early stages of PD as the blood brain barrier degrades. The surface imprinted polymer stamp is fabricated by low temperature melt stamping polycaprolactone (PCL) on interdigitated EIS electrodes. The result is a low-cost, small footprint biosensor that is highly suitable for non-invasive monitoring of the disease biomarker. The sensors were tested with αSyn dilutions in deionized water, and in constant ionic concentration matrix solutions with decreasing concentrations of αSyn to remove the background effects of concentration. The device response confirmed the specificity of these devices to the target protein of monomeric αSyn. The sensor limit of detection was measured to be 5 pg/L and its linear detection range was 5 pg/L – 5 µg/L. This covers the physiological range of αSyn in saliva and makes this a highly promising method of quantifying αSyn monomers for PD patients in the future. The SIP surface was regenerated, and the sensor reused to demonstrate its capability for repeat sensing as a potential continuous monitoring tool for the disease biomarker.

As an important organelle in eukaryotic cells, Golgi apparatus is responsible for processing and transporting proteins and lipids in cells. Precise monitoring the status of Golgi apparatus by targeting fluorescence imaging technology is of enormous importance but remains an attractive yet dramatically challenging task. In this study, we report the construction of the first Golgi apparatus targeted sensor with bright near-infrared fluorescence, termed as Golgi-Pdots. As a start point of our investigation, hydrophobic CDs with bright NIR fluorescence at 674 nm (fluorescence quantum yield : 12.18%), narrow emission band of 23 nm, and excellent stability were facilely prepared from Magnolia Denudata flowers through an ultrasonic method. Incorporating the CDs into a polymer matrix modified with Golgi-targeting molecules can produce the water-soluble Golgi-Pdots, which showed high colloidal stability and similar optical properties as compared to CDs. Further studies revealed that the Golgi-Pdots showed good biocompatibility and Golgi-targeting ability. Based on these fascinating properties, Golgi-Pdots have been successfully used for long term bioimaging of Golgi apparatus inside live cells.

In this study, we improved the photovoltaic (PV) properties and storage stabilities of inverted perovskite solar cells (PVSCs) based on methylammonium lead iodide (MAPbI3) by employing bathocuproine (BCP)/poly(methyl methacrylate) (PMMA) and BCP/polyvinylpyrrolidone (PVP) as hole-blocking and electron-transporting interfacial layers. The architecture of the PVSCs was indium tin oxide/poly(3,4-ethylenedioxythiophene):polystyrenesulfonate/MAPbI3/[6,6]-phenyl-C61-butyric acid methyl ester/BCP:PMMA or BCP:PVP/Ag. The presence of PMMA and PVP affected the morphological stability of the BCP and MAPbI3 layers. The storage-stability of the BCP/PMMA-based PVSCs was enhanced significantly relative to that of the corresponding unmodified BCP-based PVSC. Moreover, the PV performance of the BCP/PVP-based PVSCs was enhanced when compared with that of the unmodified BCP-based PVSC. Thus, incorporating hydrophobic polymers into BCP-based hole-blocking/electron-transporting interfacial layers can improve the PV performance and storage stability of PVSCs.

Synthesis of styrene butadiene hybrid latex was performed via emulsion polymerization technique using various amount of laponite clay as filler. Laponite clay was modified with cationic surfactant methyl triphenylphosphonium bromide (MTPB) with ion exchange technique prior to polymerization process. The main objective of the modification is to render the surface of the clay layers to more organophilic. Emulsion polymerization was performed under semi batch process using 2 L laboratory stainless steel reactor with temperature 85°C to 90°C for 8 hours. Polymer hybrid styrene butadiene latex was characterized for its physical and chemical properties with standard ASTM Methods. Characterization of its binding and printing properties were carried out with standard testing method (TAPPI Methods) using single coating formulation on 80 gsm woodfree paper. Polymer hybrid latex based on styrene and butadiene monomers with laponite clay enhanced binding and printing properties of coated paper, addition of laponite clay to 6.0 wt % increased the binding resistance of the coated paper two times higher than pure latex. Reducing binder level become possible for cost saving.