This study focused on the optimization of the flexural strength of bio-composite samples of palm kernel, whelks, clams, periwinkles shells and bamboo fiber, reinforced with resin for engineering applications. The aim of the study was to: formulate different samples of bio-composite reinforce with resin for engineering applications and to evaluate the flexural strength, of the fabricated composite. The hand lay-up technique was used for the composites produced by incorporating different percentage compositions of the shells/fiber (10%, 15%, 20%, 25% and 30%) into varied proportions of epoxy resin and catalyst. The cured samples after 24hours were subjected to tensile, impact, flexural and water absorption test. The experiments were conducted using Taguchi optimization method L25 (5x5) with five design parameters and five level combinations in Minitab 18 statistical software. The results showed that the average values of flexural was 114.87MPa when compared to the unreinforced of 72.33MPa bio-composite. The study recommended that agricultural waste like palm kernel shells, whelk shells, clams, periwinkle shells and bamboo fiber, should be converted into important engineering applications.

In the following work, the assessment of the strength properties of the critical area of the rotor stage of the turbine jet engine was undertaken. This is the place of fixing the blade in the rotor disc. An important aspect of this issue are characteristic geometrical dimensions and operating factors e.g., change in rotor speed. In this paper, the assessment of the strength properties of the existing trapezoidal blade-disc connection was undertaken using parametric analysis considering FSI. Virtual models of the compressor rotor stage were developed, including parametric blade-disc connections and discrete models for FEM and CFD analyses. In the parametric analysis of the blade-disc connection, one-way fluid-structure coupling was used. The parametric analysis was aimed at assessing selected geometric parameters in terms of their impact on the maximum reduced stresses in the blade root. It was examined how the adopted value of the friction coefficient influences the maximum reduced stresses in the rotor stage of the compressor.

Artificial intelligence (AI) and 3D printing (3DP) play critical roles in what is known as the 4th Industrial Revolution by developing data- and machine-intelligence-based integrated production technologies. This shift has led to increasingly complex design requirements and fabrication methods, posing several challenges for implementing design, fabrication process, and architectural quality standardization. This paper systematically reviews AI techniques applied in diverse stages of 3DP production in architecture. The research goals are to (1) offer a comprehensive critical analysis of the body of literature; (2) identify and categorize approaches to integrating AI in the production of 3D-printed structures; (3) identify and discuss challenges and opportunities of AI integration in architectural production of 3DP structures; and (4) identify gap and provide recommendations for future research. The findings indicate that topics related to AI applications are current and trending, receiving increasing attention from researchers in general and particularly those working in machine and deep learning, artificial neural networks, and pattern recognition. However, the potential of the application of AI in architectural production using additive manufacturing still needs to be explored. Considering this, the paper emphasizes the necessity of redefining traditional field boundaries and opening new opportunities in the sector.

As the core components of water jet propulsion system, water jet pump, directly affect the ship's propulsion performance. 3D reverse design method can effectively suppress the impeller secondary flow to get better performing hydraulic models. Aiming at fast and efficient optimization of the impellers, we parameterize the impellers and runner, and coupled with optimization algorithms and numerical calculations. It is an efficient and feasible way to coupling optimization based on multi-parameter, multi-objective and optimization algorithms, and parameterizing the impellers and guide vane geometry based on the 3D model designed by 3D reverse design method. In this paper, the waterjet propulsion pump is taken as the research object. According to the design method of the waterjet propulsion pump hydraulic model, the traditional axial flow blade design method, the modern ternary design theory of the blades, and the parametric three-dimensional reverse design method are selected to constructing an optimal design optimization strategy for the impeller of water-jet propulsion pump based on multi-parameter and multi-object genetic algorithm. Under the design conditions, the optimized pump efficiency reaches 89.28%, which is 1.24% higher than the original hydraulic model. The optimized pump head is 13.51 m, which is 0.39m more than the original hydraulic model. Under the design condition, the test measured head is 13.26m, the numerical calculation result is 1.88% higher than the test result, the test measured efficiency is 87.1%, the numerical calculation result is 2.5% higher than the test result. From the test results, the optimized impeller has higher hydraulic performance. Experiments have shown that it is feasible to optimize the design strategy.

Yttrium oxide (Y2O3) resistive random-access memory (RRAM) devices were fabricated using the sol–gel process on indium tin oxide/glass substrates. These devices exhibited conventional bipolar RRAM characteristics, without requiring a high voltage forming process. The effect of current compliance on the Y2O3 RRAM devices was investigated and revealed that as the set current compliance values increased, the resistance values gradually decreased. Consequently, intermediate resistance values were obtained, which are suitable for multi-level cell (MLC) switching. The fabricated Y2O3 RRAM devices were capable of functioning as an MLC with a capacity of 2 bits in one cell, utilizing three low resistance states and one common high resistance state. The potential of the Y2O3 RRAM for neural networks was further explored through numerical simulations. Hardware neural networks based on the Y2O3 RRAM demonstrated effective digit image classification with a high accuracy rate of approximately 88%, comparable to the ideal software-based classification (~92%). This suggests that the proposed RRAM has the potential to be utilized as a memory component in practical neuromorphic systems.

Abstract: Interface risks are inherent in every construction project from start to finish. Identifying and managing these risks effectively in every project phase is crucial for actualising project objectives. This paper shows a comprehensive framework showing several relationships between project stakeholders and how the interface risks between them that influence project execution are identified and managed for the overall construction project success. Firstly, literature review on interfaces and interface risks were car-ried out and how organisations managed interface risks were discussed and secondly, the collection of quantitative data was conducted by means of structured online questionnaires. The sample consisted of 205 construction project professionals who were selected randomly. This group included individuals with various roles in the construction industry, The data was analysed using descriptive statistical methods, including factor analysis, reliability assessment, and calculations of frequencies and percentages. Finally, the results showed all the factors, work culture and organisational approaches that influence interface risk management and ways to identify and manage interface risks effectively.

Remote sensing imagery is of great significance for policy decisions, especially for disaster assessment and disaster relief. To ensure the privacy and inviolability of personal buildings, the information containing these buildings must be anonymized during the remote sensing mapping process. Traditional processing methods for these targets in remote sensing mapping are mainly based on manual retrieval and image editing tools, which are inefficient. Deep learning provides a new direction for target hiding. Although the image inpainting method based on deep learning is faster than the manual method, the cost of training calculation is a disadvantage. And the element-wise product operation used in the model increases the risk of vanished or exploded gradients. We propose a Residual Attention Target Hiding (RATH) model for remote sensing target hiding based on deep learning. RATH uses residual attention modules to replace gated convolutions, reducing parameters and mitigating gradient issues. The residual attention module preserves gated convolution performance but provides an adjustable kernel size. RATH retains gated convolutions for dynamic feature selection and balances model depth and width. Furthermore, this paper modifies the contextual attention layer by adjusting the fusion process to enlarge the fusion patch size. Finally, we extend the edge-guided function to preserve the original target information and confound viewers. Ablation studies on an open dataset prove RATH’s efficiency for image inpainting and target hiding. RATH achieves state-of-the-art results with lower complexity. And it has the highest similarity for edge-guided target hiding. RATH enables robust, efficient target hiding for privacy protection in remote sensing imagery while balancing performance and complexity. Experiments show RATH's superiority over existing methods in hiding arbitrary-shaped targets.

In the past few decades, the use of agricultural waste has been increasing due to the increasing demand for sustainable materials. This paper aims to review the significance of agricultural waste as a type of wealth and its potential as an alternative material in the composite field. It was found that many agricultural wastes had been utilized in various production of ecological products. The review discusses the physical, mechanical, and chemical properties of the natural fibers made from agricultural waste and the use of Pineapple Leaf Fiber Reinforced Composite to manufacture UAVs (Unmanned Aerial Vehicles). The extracted waste fibers’ physical, mechanical, and chemical properties show that these agricultural wastes can produce better advanced composite materials suitable for structural applications. The use of pineapple leaf fiber in Unmanned Aerial Vehicles manufacturing has the potential to revolutionize this industry and contribute to a more sustainable future.

The mechanism of anionic/cationic combination collector ST-8 for the efficient separation of spodumene and feldspar was investigated by flotation tests, surface tension measurements, zeta potential measurements and infrared spectroscopy analysis. The flotation results indicated that when the optimum molar combination of sodium oleate and dodecylamine was 6:1-10:1 and pH=8.5 or so, the recovery of spodumene reached a maximum of 80% and that of feldspar reached about 24.5%. Zeta potential measurements showed that the negative shift of the kinetic potential on the surface of spodumene was much stronger than that on the surface of feldspar, indicating that the adsorption capacity of the combined collector on spodumene surface and feldspar surface was greatly different. From the surface tension as well as the synergistic parameters, there was a strong mutual attraction between dodecylamine and sodium oleate, and there was a significant synergistic effect between them. Infrared spectroscopy indicated that the combined collector chemisorbed on the mineral surface, and the intensity of the absorption peak after the action of spodumene was much stronger than that after the action of feldspar. The solution chemistry of the combined collector revealed that at pH 8.5, the positively charged ions RNH3+ and (RNH3+)22+ in dodecylamine and the negatively charged RCOO- and (RCOO-)22- ions in oleic acid form highly reactive complexes to interact with the mineral surface by electrostatic gravitation, thus achieving efficient separation of spodumene and feldspar. Finally, from the closed circuit test results, a flotation index of 6.34% Li2O grade and 88.51% Li2O recovery was obtained.

Monitoring the quality of stored bulk grain is generally done using temperature cables hung from silo roofs. Little investigation has been done into the effects of number of sensors and their placement in terms of reliability of the monitoring system with regard to making stored grain quality management decisions. A previously developed 3D finite element simulation model was verified and used to investigate these aspects. In the first study, a silo was loaded with about 228.6 Mg (9000 bushels) of maize and six temperature cables were placed in the grain mass. The maize was aerated continuously for a period of two weeks, and the cable sensor temperatures were compared to the predicted temperatures which were in close agreement with the observed readings. The standard error of prediction ranged from 2.0 to 3.7°C. In the second study, 15 and 30 sensors were placed at manufacturer recommended depths and horizontal locations in the grain mass of three silo sizes (i.e., 11x11, 14.6x14.6 and 14.6x18.3 m diameter by eave height). The average grain temperatures predicted by the 15 and 30 sensors over a one-year simulation period were compared to the average grain temperatures predicted for the entire grain mass (1968, 3052, and 3204 mesh nodes). The number of sensors needed to monitor stored grain temperatures reliably in the three silo sizes investigated heavily depended on whether the aeration control strategy achieved a sufficiently low temperature by the time the aeration fans were turned off and sealed ahead of the non-aerated storage period. Fifteen or 30 sensors were sufficient to monitor grain temperatures during the aeration cooling period but for the two larger silo sizes more than 30 sensors would be needed during the storage period. As silo size increased, and surface-to-volume ratio decreased, grain temperatures remained lower during the storage period. Results support the best management practice recommendation of leaving cooled grain cold and not warming it up in the spring ahead of storage into the summer.

Convolution forms one of the most essential operations for the FPGA-based hardware accelerator. However, the existing designs often neglect the inherent architecture of FPGA, which puts forward an austere challenge on hardware resource requirements. Even though some previous works have proposed approximate multipliers or convolution acceleration algorithms to deal with this issue, the inevitable accuracy loss and resource occupation easily lead to performance degradation. Toward this, we first propose two kinds of resource-efficient optimized accurate multipliers based on LUTs or carry chains. Then targeting FPGA-based platforms, a generic multiply-accumulate structure is constructed by directly accumulating the partial products produced by our proposed optimized radix-4 Booth multipliers without intermediate multiplication and addition results. Experimental results demonstrate that our proposed multiplier achieves a maximum 51% look-up-table (LUT) reduction compared to the Vivado area optimized multiplier IP. Furthermore, the convolutional process unit using the proposed structure achieves a 36% LUT reduction compared to existing methods. As case studies, the proposed method is applied to DCT transformer and LeNet to achieves hardware resource saving without loss of accuracy.

Wearable touch sensors, which can convert force or pressure signals into quantitative electronic signals, have emerged as an essential smart sensing devices and played an important role in various cutting-edge fields, including wearable health monitoring, soft robots, electronic skin, artificial prosthetics, AR/VR, and the Internet of Things. Flexible touch sensors have made significant advancements, while construction of novel touch sensors via mimicking the unique properties of biological materials and biogenetic structures always remains a hot research topic and significant technological pathway. This review provides a comprehensive summary of the research status of wearable touch sensors constructed by imitating the material and structural characteristics in nature, and also summarizes the scientific challenges and development tendency of this aspect. Firstly, the research status for constructing flexible touch sensors based on biomimetic materials is summarized, including hydrogel materials, self-healing materials, and other bioinspired or biomimetic materials with extraordinary properties. Then, design and fabrication of flexible touch sensors based on bionic structures for performance enhancement are fully discussed. These bionic structures include special structures in plants, special structures insects/animal, and special structures in human body. Moreover, a summary of the current issues and future prospects for developing wearable sensors based on bioinspired materials and structures is discussed.

3D/4D printing technologies are currently among the fastest growing, cutting edge fabrication technologies. The scale of their applications is vast and applicable to nearly all industries. 3D printing technologies are particularly popular in robotics, and especially in advanced design innovative solutions for areas such as manufacturing, space technology and medicine. The development of robotics, and in particular of the precision of manufactured components, such as actuators, pneumatic muscles, power transmission units, etc., means that new prototypes are still being made, where the use of 3D printers reduces the production time severalfold and allows for completing the necessary simulations and tests. In addition, the use of 3D printers allows for the production of thin-walled and cellular structures, which is a great advantage compared to conventional fabrication technologies. In the range of 3D printers available on the market, only a few selected technologies allow for actual use in the construction of advanced robot elements (muscles, vibration dampers, etc.). In the era of rapid growth of the precision of the available 3D printers and modern materials, 3D printing may soon become a major tool in robotics. This article presents an overview of 3D printing technologies and materials in terms of their application in robotics and provides examples of the use of 3D and 4D printing in prototyping and fabrication of robotic elements with particular emphasis on the current state of the art. The study considered the possibilities of using 3D/4D printing in robotics with the use of polymeric materials. The review of the literature and the research work currently being carried out in this area is very promising and it seems that 3D/4D printing in robotics is widely used and is still developing, which allows to conclude that in the near future the number of research works in this field will increase rapidly.

Our research aims to address the urgent need for retrofitting measures to enhance the resilience of damaged coupling beams in real-life scenarios. We conducted a series of tests on scaled-down prototype coupling beams, carefully adhering to similarity theory requirements to ensure accurate representation. The test results showed that the chord rotation capacities of different specimens with the same diagonal bundle varied significantly due to the difference in the confinement levels. The specimens with lower level of confinement were found to have less displacement capacity. When the specimens were strengthened by wrapping with GFRP after damage, it was observed that the increase in confinement level significantly increased the chord rotation capacities of all specimens. In addition, in the tests before the strengthening, the elongation behavior of the specimens is observed until the damage development reaches approximately 2% chord rotation. With the in-crease in chord rotation, the elongation behavior of the specimens stops with increasing damage and then shortening behavior is observed. After retrofitting, it was observed that the axial elongation continued in a limited manner depending on the location and size of the concrete separated from the beam core in the case of collapse before strengthening, and then the beam showed a shortening behavior predominantly. After strengthening studies, our findings contribute valuable insights into the behavior and performance of damaged coupling beams, emphasizing the potential of urgent GFRP wrapping as a viable solution to enhance the seismic resilience of middle- and high-class buildings with structural walls after seismic events.

For enhancing the efficiency of cantilever casting the construction in the bridge, a novel rhombus traveling track of hanging basket was developed and optimized. The civil software titled Midas was applied to analyse the mechanical properties of the hanging basket with full load and control load. The strength and distortion of the walking mechanism were within the specified range when the maximum beam unit internal force of 149.69Mpa, which was less than the allowable stress of steel 175Mpa, and the anti-overturning safety factor of the hanging basket was 2.5 to meet the requirements. Through the comparative analysis of the key components and the finite element calculation, it was found that there was about 30% redundancy in the structure performance. Therefore, further optimization of each structure was carried out, and the front elevation of the main truss of 20° was achieved. It obtained the best performance in all aspects.

Keywords: Baseband, GeoSurf Constellation, Interference, Linear Distortions, Passband, Time Delay, Rain attenuation, Synthetic Storm Technique, ultra–wideband.

The present investigation focuses on the impact of jet nozzle orientation on mixing time in a cylindrical tank. The aim is to identify nozzle positions that improve mixing performance and to elucidate the governing parameters that influence it. A water tank was employed for the experiment. The vertical inclination angle (α) and the horizontal inclination angle (β) of the jet nozzle determined the nozzle positions. Mixing time was determined using an inert tracer and spectrophotometry measurements. The findings show that the mixing time is significantly influenced by the position of the jet nozzle position. The accuracy of existing jet turbulence and the circulation models for the prediction of mixing time was evaluated for the different nozzle positions. Our results indicate that both models provide accurate predictions for the conventional centrally aligned (β = 0°), upward-pointing jet nozzle positions only (α > 0). For the other nozzle positions where β > 0° and at varying α, the data follow the same trends as the jet turbulence and circulation models, however, the proportionality constants vary. Shorter mixing times can be attributed principally to longer jet path lengths and therefore higher fluid entrainment and circulation, as well as higher dissipation rates per jet length squared. However, it is suspected that the 3-dimensional nature of the flow pattern generated in the tank also plays a non-negligible role since mixing is hindered when the nozzle points more towards the tank wall.

This paper describes the indoor air pollution in urban (Lahore, Faisalabad, Gujranwala, Rawalpindi and Karachi) Pakistani regions while considering the outdoor air and the health and wellbeing of the occupants present indoors. It also aims to assess previous methodological approaches Such as Air Conditioning Systems, used by developed countries to improve air quality to demonstrate the improvements that can be made in air quality in Pakistani urban areas. This research also investigates the causes, concentration and effects of poor air quality in Pakistani urban areas such as particulate matter (PM2.5), carbon oxides (COx), nitrogen oxides (NOx), sulphur oxides (SOx) and volatile organic compounds (VOC’s). The average concentration of these pollutants in Pakistan’s indoor air is, particulate matter (PM): [100 – 250 µg/m3 for PM2.5, 200 – 600 µg/m3 for PM10] 1 – 20 ppm for carbon monoxide (CO), nitrogen oxides (NOx): [50 – 100 µg/m3 for NO2, 20 – 40 µg/m3 for NO], 20 – 50 µg/m3 for sulfur dioxide (SO2), volatile organic compounds (VOCs): 0.1 – 0.5 ppm for formaldehyde, 5 – 10 µg/m3 for benzene and 20 – 30 µg/m3 for toluene. It should be noted that these concentrations can differ depending on the origin of pollution, location, and time of day. The literature review is made up of a combination of descriptive research methods that are used to inform the research background of ambient and indoor air quality, thus the literature review provides a theoretical and methodological background about the air pollution and its improvement in different parts of the world. According to the World Air Quality Index, Pakistan is the third most polluted country in terms of average PM2.5 concentration which is 14.2 times the WHO annual air quality guideline value. As a result, it is suggested that a PM2.5 concentration reduction program be implemented in urban Pakistani regions' indoor air.

In order to apply visible light communication systems in different scenarios, this article utilizes an excellent temperature adjustable light source mixed with RGB LEDs, and applies it in a visible light communication system. It utilizes color division multiplexing technology to achieve three-channel communication, thereby improving the communication bandwidth of the system. The communication system adopts three constant current driving circuits to control the duty cycle of Pulse Width Modulation (PWM) of each channel, thereby changing the proportion of RGB LEDs, and obtaining different color temperatures to achieve the purpose of color control for mixed color LEDs. The experimental results show that when adjusting the color temperature, the change in luminous flux is very small, with fluctuations of less than 2.24%; When adjusting the brightness, the color temperature fluctuation is within 40K, which is less than the 50K color temperature limit that the human eye can distinguish, and the average color temperature error is 0.609%; Color tolerance less than 5.5×10-3 indicates good dimming effect, and the communication performance of the system is better in the high color temperature range, which is significantly superior to the low color temperature range. When the error rate is below 3.8×10-3, the total modulation bandwidth of the three channels reaches 11.7 MHz.

Due to urban warming, energy demand for cooling buildings is rising. The current study used CitySim to estimate the cooling energy requirements for 40 buildings in Downtown, Dubai using high-resolution climate data from weather research and forecasting (WRF) coupled with single layer urban canopy model (SLUCM). Simulating the four mitigation scenarios allowed for the examination of the reduction in cooling load caused by the addition of greenery at a rate ranging from 25% to 100%. The insulated building's cooling demand reduced by a maximum of 13.89% under 100% GI (M4). Scenario M4 resulted in a reduction of 4.6 kWh/m2 and 3.1 kWh/m2 for the non-insulated and insulated low-rise residential buildings, respectively, while the high-rise buildings saw a reduction of 3.09-4.91 kWh/m2 for the non-insulated and 2.07-3.09 kWh/m2 for insulated buildings. This study offered a potential remedy to deal with the problem of urban heating in subtropical environments.

Anode bonding is a widely used method for fabricating devices with suspended structures, and this approach is often combined with deep reactive ion etching (DRIE) for releasing the device. However, the DRIE process with a glass substrate can potentially cause two critical issues: heat accumulation on the suspended surface and charging effects resulting from the reflection of charged particles from the glass substrate. In particular, for torsional bars with narrow width, the heat accumulated on the suspended surface may not dissipate efficiently, leading to photoresist burning and subsequently resulting in the fracture of the torsional bars. Moreover, once etching is finished through the silicon diaphragm, the glass surface becomes charged, and incoming ions are reflected towards the back of the silicon, resulting in the etching of the back surface. To address these issues, we proposed a method of growing silicon oxide on the back of the device layer. By designing, simulating, and fabricating electrostatic torsional micromirrors with common cavity silicon-on-glass (SOG) structures, we successfully validated the feasibility of this approach. This approach ensures effective heat dissipation on the suspended surface, even when the structure is over-etched for an extended period, and enables the complete etching of torsional bars without adverse effects due to the overheating problem. Additionally, the oxide layer can block ions from reaching the glass surface, thus avoiding the charging effect commonly observed in SOG structures during DRIE.

The objective of this study was to apply simulation and computational intelligence techniques using artificial intelligence and genetic algorithm for economic and environmental optimization of the reverse network (manufacturers, waste managers and recyclers in São Paulo, Brazil) of waste electrical and electronic equipment (WEEE) to promote circular economy. For the economic evaluation, the reduction of: fuel, drivers, insurance, depreciation, maintenance and charges was considered and for the environmental evaluation, the environmental impact was measured in the abiotic, biotic, water, land, air and greenhouse gases compartments. It is concluded that the optimized structure of the WEEE reverse chain for São Paulo, Brazil reduced the number of collections, making the most of the cubage. It also generated economic and environmental gains, contributing to the strategic actions of the circular economy. Thus, the proposed simulation allows replication in organizational practice, mainly to meet the 2030 agenda on reducing the carbon footprint generated in transport in large cities. Thus, this study can guide companies on structuring the reverse WEEE chain in São Paulo, Brazil for economic and environmental optimization, a relevant aspect considering the exponential generation of WEEE, requiring the implementation of the national solid waste policy, and subsequently the signature of the electronics sector agreement in São Paulo.

Although buildings constitute 35% of global energy use and 38% of carbon emissions from energy, the amount of energy and energy-related carbon emissions are increasing rapidly. On the other hand, non-renewable usable energy resources are decreasing on the contrary. New buildings are being built due to the increasing population and the existing building stock not meeting the needs or losing its lifespan. Some of the existing building stock is demolished and renewed for structural reasons and some for reasons such as usage performance. It is possible to reduce both energy consumption and greenhouse gas emissions with strategic energy uses in existing building stocks. There are various techniques to measure the maximum performance of sustainable and energy-efficient use of existing building stocks with which changes. Building Information Modeling (BIM) technology is one of these techniques that provides wide opportunities to users in recent years, and it is almost a virtual laboratory of structures. Building stocks can be modeled with BIM, and alternative shell and system suggestions can be used to measure how building performance has changed and to achieve the best results. In this research study, improvement scenarios that optimize energy use in existing building stocks are investigated on a sample residential building by using the virtual laboratory facilities of BIM. After measuring the current energy performance of the existing building with BIM tools, 192 alternative results were obtained with 6 variables (external walls, roof, insulation layers, transparent surface materials, lighting, and photovoltaic panels). The obtained alternatives were compared with the current state of the existing building. The material expenditures and amortization periods required for these alternative scenarios are also calculated. The results obtained were evaluated according to annual / lifetime energy consumption, fuel, electricity, initial investment costs, energy use intensity, and carbon emission amounts. With the optimization of the current situation of the sample building, annual fuel consumption decreased by 61% and electricity consumption by 64%. The amortization period of the optimum improvement was determined as 12 years.

In vivo, articular cartilage tissue is surrounded by a cartilage membrane, and HP (HP) and compressive strain increases simultaneously with the compressive stress. However, it has been impossible to investigate the effects of simultaneous loading in vitro. In this study, a bioreactor capable of applying compressive stress under HP was developed to reproduce ex vivo the same physical loading environment found in cartilage in vivo. First, a HP stimulation unit was constructed to apply cyclic HP pressure-resistant chamber by controlling a pump and valve. A compression-loading mechanism that can apply compressive stress using an electromagnetic force was implemented in the chamber. The synchronization between the compression and HP units were evaluated and the stimulation parameters were quantitatively evaluated. Physiological HP and compressive strain were applied to the chondrocytes encapsulated in alginate and gelatin gels after applying high HP at 25 MPa, which induced damage to chondrocytes. It was found that compressive stimulation increased the expression of genes related to osteoarthritis. Furthermore, the simultaneous application of compressive strain and HP, which is similar to the physiological environment in cartilage, had an inhibitory effect on the expression of genes related to osteoarthritis. HP alone also suppressed the expression of osteoarthritis-related genes. Therefore, the simultaneous hydrostatic and compressive stress-loading device developed to simulate the mechanical environment in vivo may be an important tool for elucidating the mechanisms of disease onset and homeostasis in the cartilage.

A composite beam is a structural member that behaves as a single unit by using shear connectors between a concrete slab and an H-shaped steel girder. The composite ratio is crucial and determined by the shear connectors' ability to withstand the horizontal shear forces between the concrete and steel girder. In this study, a U-shaped composite beam was designed, which differs from conventional composite beams as it allows the use of a steel girder as a formwork. Moreover, angle-type shear connectors, instead of stud-type connectors, were employed. Based on this design, large-scale U-shaped composite beams with angle-type shear connectors were fabricated, and load tests were conducted to analyze the behavior after composite action and the influence of shear connector spacing. Additionally, the strength of the angle-type shear connectors used in this paper was evaluated through finite element analysis. Finally, a strength evaluation method for composite beams of this configuration was proposed.

The ozonation reaction in a bubble column reactor (BCR) has been widely used in the removal of phenol from wastewater, but the phenol removal efficiency in this type of reactor is limited because of low ozone solubility and reactivity in the system. In the present study, the phenol degradation was enhanced using α-Al2O3 as a packing material and a ZnO nanocatalyst in the BCR. The reactor diameter and height were 8 cm and 180 cm, respectively. The gas distributor was designed to include 52 holes of 0.5-mm diameter. Also, the gas holdup, pressure drop, and bubble size were measured as a function of the superficial gas velocity (i.e., 0.5, 1, 1.5, 2, 2.5, and 3 cm/s). The evaluation of the hydrodynamic parameters provided a deep understanding of the ozonation process to select the optimal operating parameters in the reactor. It was found that the best superficial gas velocity was 2.5 cm/s. A complete (100%) phenol removal was achieved for phenol concentrations of 15, 20, and 25 ppm at reaction times of 80, 90, and 100 min, respectively, using α-Al2O3 packing material and a ZnO nanocatalyst in the BCR. Additionally, the results provided a clear reaction mechanism describing the ozonized BCR. Finally, the applied treatment method can be used efficiently to remove phenol from wastewater at a low cost, with little consumed energy, and a simple operation.

: In Chile, most tailings impoundments are in Northern and Central Chile, 20% of them are abandoned. Municipal budgets to manage these environmental liabilities are very limited and the use of native and endemic plant species to remove heavy metals from tailings is a low-cost alternative. Ex-situ phytoremediation experiments were conducted over seven months to evaluate the potential of Lycium chilense and Haplopappus foliosus to remove copper and lead from mine tailings. The results indicate that both species can concentrate high levels of both elements and they present removal efficiencies for Cu close to 50%. The best performance was presented by Haplopappus foliosus, accumulating higher concentrations of both metals than Lycium chilense. Also, it presents a bioconcentration over 1.

In the clock network design, the trade-off between power consumption and timing closure is an important and difficult issue. To achieve this target, a hybrid clock network architecture that combines both clock tree and clock mesh seems to be a promising solution. In this paper, we propose a novel clock mesh architecture – cross-mesh, with the average dispersion of the overall driving force, our methodology creates small non-zero skew clock trees. In addition, we integrate clock gating and register clustering techniques to further reduce dynamic power consumption. The proposed algorithms have four stages: cross-mesh planning, register clustering, mesh line connecting, and load balancing. Experimental results show that our methodology and algorithms get feasible solution effectively and improve both power consumption and clock skew simultaneously.

Abstract: The surge of diabetes poses a significant global health challenge, particularly in Oman and the Middle East. Early detection of diabetes is crucial for proactive intervention and improved patient outcomes. This research leverages the power of machine learning, specifically, Convolutional Neural Networks (CNNs), to develop an innovative 4D CNN model dedicated to early diabetes prediction. A region-specific dataset from Oman is utilized to enhance health outcomes for individuals at risk of developing diabetes. The proposed model showcases remarkable accuracy, achieving an average accuracy of 98.49% to 99.17% across various epochs. Additionally, it demonstrates excellent F1 score, recall, and sensitivity, highlighting its ability to identify true positive cases. The findings contribute to the ongoing effort to combat diabetes and pave the way for future research in using deep learning for early disease detection and proactive healthcare.

MgB2 is a hexagonal superconducting material, and its simple composition has led to the development of low-cost practical wires. However, the problem is that the strain characteristics of filaments are inferior to those of other practical wires, but there have been no strain measurements using diffraction method. The reason for this is presumably that it is a little too thick for synchrotron radiation measurements, and the large absorption cross section of the included boron-10 makes it difficult to obtain elastic scattering for neutron measurements. We prepared a wire substituted with boron-11, an isotope with small neutron absorption cross section, and attempted to measure its strain under tensile loading using pulsed neutron.

Fault detection in PV arrays and inverters is critical for ensuring maximum efficiency and performance. Artificial intelligence (AI) learning can be used to quickly identify issues, resulting in a sustainable environment with reduced downtime and maintenance costs. As the use of solar energy systems continues to grow, the need for reliable and efficient fault detection and diagnosis techniques becomes more critical. This paper presents a novel approach for fault detection in photovoltaic (PV) arrays and inverters, combining AI techniques. It integrates Elman Neural Network (ENN), Boosted Tree Algorithms (BTA), Multi-layer Perceptron (MLP), and Gaussian Processes Regression (GPR) for enhanced accuracy and reliability in fault diagnosis. It leverages their strengths for accuracy and reliability of fault diagnosis. Feature engineering-based sensitivity analysis was utilized for feature extraction, the fault detection and diagnosis were assessed using several statistical criteria including PBAIS, MAE, NSE, RMSE, and MAPE. Two intelligent learning scenarios are carried out, the first scenario is done for PV array fault detection with DC power (DCP) as output. The second scenario is done for inverter fault detection with AC power (ACP) as the output. The proposed technique is capable of detecting faults in PV arrays and inverters, providing a reliable solution for enhancing the performance and reliability of solar energy systems. Real-world solar energy dataset is used to evaluate the proposed technique, with results compared to existing detection techniques and obtained results show that it outperforms existing fault detection techniques, achieving higher accuracy and better performance. The GPR-M4 optimization justified reliably among all the models with MAPE=0.0393, and MAE=0.002 for inverter fault detection and MAPE=0.091, and MAE=0.000 for PV array fault detection.

Approximately 2 TCF (Trillion Cubic Feet) of acid gas are projected to be injected into the Surmeh formation. The recommended injection rate is 180 MMSCFD (Million standard cubic feet per day), based on acid gas content and gas in place of the source of injection. The tight nature of the Surmeh formation limits injectivity, with a maximum achievable rate of 7 MMSCFD for permeability of 1 mD (millidarcy). However, higher porosity (12%) and permeability of 100 mD enable more efficient injection without fracturing the formation. This study provides valuable insights into the feasibility of AGI in saline aquifers, emphasizing reservoir characterization, geomechanics, caprock integrity, and rock properties. The findings contribute to the implementation of environmentally sustainable acid gas disposal at offshore reservoirs.

Electrical energy demand increase does evolve rapidly due to several socioeconomic factors such as industrialization, population growth, urbanization and of course the evolution of modern technologies in this 4th industrial revolution era. Such rapid increase in energy demand introduces a huge challenge in power system. Such has paved way for network operators to seek for alternative energy resources other than the conventional fossil fuel system. Hence, the penetration of renewable energy into the electricity supply mix has evolved rapidly in the past three decades. However, the grid system has to be well planned ahead to accommodate such increase in energy demand in the long run. Transmission Network Expansion Planning (TNEP) is a well ordered and profitable expansion of power facilities that meets the expected electric energy demand with an allowable degree of reliability. This paper proposes a TNEP model that minimises the network reinforcements, operational costs and costs of renewable energy penetrations, while satisfying the increase in demand. The problem is formulated as a mixed integer linear programming (MILP) problem. The developed model has been tested in several IEEE test systems in multi-period scenarios. The paper also carried out a detailed derivation of the new non-negative variables in terms of the power flow magnitudes, the bus voltage phase angles and the lines’ phase angles for proper mixed integer variables’ decomposition techniques. Moreover, this paper tends to provide additional recommendation in terms of which particular year (within 20 years of planning period) can the network operators install new line(s), new corridor(s) and/or additional generation capacity to the respective existing power networks. Such is achieved by running incremental periods simulations from base year through the planning horizon. The results show the efficacy of the developed model in solving the TNEP problem with a reduced and acceptable computation time even for large power grid system.

The demand for improving the nuclear waste management has since long been identified as one of the major hurdles for widespread use of nuclear energy. Nuclear waste management, through partitioning and transmutation (P&T) has been researched since the 1990ies with partitioning being a pre-requisite for the process. Recently, an innovative approach of reactors directly operating on spent nuclear fuel, iMAGINE, has been proposed which could deliver on the aims of P&T as a side effect to more efficient nuclear energy production in the future. The results shown here confirm that it is possible to achieve the aims of P&T without prior partitioning, but it is certainly less efficient since the high concentration of MAs, required for efficient burning, are impossible to obtain in a short operational time. The proposed nuclear waste management approach will be a long-term effort when it is accomplished without partitioning/separation technologies. However, none of the analyses contradicts this effort – the key points are a) when the technology for treating the waste is possible and reliable, the time horizon will not be a major concern b) the waste management is now intrinsically linked with energy production instead of requiring dedicated costly facilities, delivering a promising economic basis c) the waste management is now associated with long-term energy production and massively improved resource utilization. In summary, the objectives of P&T are achievable without prior partitioning – this is a ground-breaking result. However, the approach will require continued nuclear energy production for a very long time. In case of a nuclear phase-out decision, a much more efficient transmutation scenario would have to be envisaged as already discussed several years ago for Germany.

Shaped surfaces are increasingly used in the field of mould making for casting or injection moulding, where future products include shapes with different curvatures. These are surfaces that form convex curves, concave curves, or a combination thereof. Given these machined surfaces, it is important to know the impact of the finishing strategies on these surfaces. This paper deals with the comparison of finishing milling strategies in the production of shaped surfaces and the analysis of different methods for the evaluation of surface topography, surface roughness and the evaluation of deviations. The material used for the experiments was AlCu4Mg aluminium alloy, and Constant Z, Spiral and Spiral circle strategies were chosen for the finishing strategies. The evaluation of surface topography and surface roughness was carried out at three different sample heights with respect to the tool contact with the machined surface. The results showed changes in the toolpaths due to the variation of the effective diameter of the tool cutter to the machined surface as well as the choice of strategy. To produce specimens with corresponding shapes in terms of topography, the Constant Z strategy was the most suitable, in which uniform toolpaths were obtained over the whole height of the sample.

With increasing power and speed of laser welding, in-process monitoring has become even more crucial to ensure process stability and weld quality. Due to its low cost and installation flexibility, acoustic process monitoring is a promising method and has demonstrated its effectiveness. Since its feasibility has been the focus of existing studies, the temporal resolution of acoustic emissions (AE) has not yet been addressed despite its utmost importance for realizing real-time systems. Aiming to provide a benchmark for further development, this study investigates the relationship between duration and informativeness of AE signals during high power (3.5kW) and high speed (12m/min) laser beam butt welding. Specifically, the informativeness of AE signals is evaluated based on the accuracy of detecting and quantifying joint gaps for various time windows of signals, yielding numerical comparison. The obtained results show that signals can be shortened up to a certain point without sacrificing their informativeness, encouraging to optimize the signal duration. Our results also suggest that large gaps (> 0.3mm) induce unique signal characteristics in AE, which are clearly identifiable from 1 ms signal segments, equivalent to 0.2mm weld seam.

The cutter structure and layout scheme of PDC (Polycrystalline Diamond Compact) bits are important factors in improving efficiency. To further improve the drilling efficiency of PDC bits, axe, triangular prism, and cylindrical PDC cutters were used as research objects. Based on the measured granite data, a finite element model of non-homogeneous granite was established and verified by uniaxial compression simulation. The rock-breaking process of different cutter combination schemes was compared using the finite element method, and the parameters in the best scheme were optimized using the Box-Behnken response surface method. The results show that the constructed model of non-homogeneous granite is consistent with the stress-strain relationship of real granite and is reliable. The axe PDC cutter is more aggressive than the other two cutters and is more suitable for the front row of the bit blade tooth arrangement, while the triangular prism cutter is the second most aggressive and is suitable for the rear row of tooth arrangement, and the best combination scheme is the front row of axe cutter and the rear row of triangular prism cutter arranged alternately with the axe cutter. The optimal transverse and longitudinal distances of the optimized triangular prism cutter from the front axe cutter are 10mm and 7mm, and the optimal transverse and longitudinal distances of the rear axe cutter from the front cutter are 10.06mm and 7mm. The drilling speed is more stable during drilling and the PDC bit with mixed tooth arrangement has 16.8% and 16.6% higher rate of penetration(ROP) compared with the bit with single axe cutter and triangular prism cutter, and the drilling speed is more stable during working, which can effectively improve the rock breaking efficiency of the PDC bit. The field application proves that the bit with mixed cutter arrangement is easier to break the complex formations, with more stable ROP and better efficiency. The study can provide theoretical support for the cutter layout of the PDC bit.

Many parameters and complex boundaries are involved in the spatial arrangement of an under-ground powerhouse for a hydropower station, which requires reference to many relevant cases and specifications. However, in practical applications, retrieving relevant cases or specifications is difficult, and there is a lack of knowledge of cascading logic among design parameters. For this question, a targeted knowledge graph based on knowledge graph management technology is established to support subsequent applications. This paper proposes a new concept of con-structing a knowledge graph for building information modeling (BIM) underground power-houses of hydropower stations. Firstly, the ontology skeleton of hydropower station spatial ar-rangement design, which represents the knowledge organization structure of the knowledge graph, is reconstructed by carefully analyzing the requirements for intelligent modeling of un-derground powerhouses. A large amount of unstructured data is identified based on optical character recognition (OCR) technology and is divided into words to extract correlation knowledge based on THULAC. In the next step, the knowledge triad of the spatial arrangement of the underground powerhouse is extracted based on ChatGPT and stored in a Neo4j knowledge base to build a knowledge graph. Finally, the knowledge graph is serviced to realize the query of knowledge and parameter recommendation to assist the digital intelligent design of spatial arrangement of an underground powerhouse of pumped storage hydropower stations.

In the last decades, climate and environmental changes have highlighted the fragility and vulnerability of the landscape, especially in mountain areas where the effects are most severe. The strategy for hazard mitigation must deploy synergistic actions based on a thorough knowledge of the territory and its phenomena to enable integrated and effective land planning and management through suitable communication tools. This study promotes the methodological setup of a Landscape Digital Twin to establish a multi-disciplinary and multi-scalar hazards overview according to a matrix framework implementable over time and space. The original contribution to the research addresses a holistic vision that combines meaningfully qualitative with quantitative approaches to generate risk maps by integrating various indicators within a multi-hazard framework from the socio-economic perspective. This contribution presents road network risk analysis by exploiting flooding and landslide scenarios. The critical road segments or nodes most vulnerable or impacted by network performance and accessibility can be identified with minimal preprocessing from credible open-source sources. The method's applicability is tested in a Piedmont Region, northern Italy case study. The integration proposed will help generate comprehensive risk analysis maps that effectively portray the interconnectedness among natural hazards, infrastructure, and socio-economic factors fostering more resilient decision-making processes.

The ultimate aim of dynamic load balancing in cloud computing systems is to maximise the efficiency with which resources are utilised and workloads are distributed. Given that load balancing is a multi-objective process and that response time is a priority, the Harris hawk optimisation (HHO) algorithm was developed as a unique solution for dynamic load balancing. Based on burden distribution and resource utilisation, the HHO algorithm is responsible for dynamically assigning workloads to virtual machines (VMs). Through iterative interactions and position updates, the hawks investigate the solution space, determine the optimal method for dividing the work, and adapt to the ever-changing conditions of the workload. The HHO algorithm has been demonstrated to be effective and efficient in the management of dynamic load balancing via a series of experimental evaluations and comparisons with other load-balancing approaches. These discoveries have led to quicker response times and more efficient resource utilisation. Utilising the collaborative search behaviour of hawks, this technique provides a solution that is both practicable and effective for addressing load balancing concerns in dynamic scenarios.

Solid spent nuclear fuel from nuclear power plants has 3.4% fission products (80-160amu), contributing to over 99.8% radioactivity. On the other hand, liquid high-level radioactive waste (HLRW) from spent fuel reprocessing has 98.9% bulk elements (0-60amu) with 0.1% radioactivity. A separation mechanism on the mass categories as groups presents unique opportunities in managing HLRW for the long term with a considerable cost reduction. This paper proposes a thermal plasma-based separation system incorporating atmospheric pressure plasma torches for HLRW mass separation into low-resolution mass groups. Several engineering issues, such as waste preparation, waste injection into the plasma and waste collecting after mass separation, need to be addressed. Using COMSOL Multiphysics simulation, the generic system can be studied using noble gas mass separation and further analyze the mass filter capabilities. This paper provides the history of plasma-based mass separation. Functional modelling of a thermal plasma mass separation system is proposed under atmospheric pressure. Finally, aspects of mass separation simulation using noble gas Argon and Helium inside the plasma mass separation system were studied in COMSOL Multiphysics.

With advances in information technology, big data, mobile communications, and robotics, digital technologies are increasingly being used in factories around the world. This digital transformation is named industry 4.0. Today, industrial companies are looking at how to adopt this era and implement these technologies 4.0 while improving their performance and generating more profits. The objective of this paper is to help companies to better choose the appropriate digital technologies according to their activities using a multi-experts-multi-criteria decision-making approach under hesitant fuzzy information. The proposed model is a generic model based on Multi-Agent Systems allowing to have an idea of the parameters necessary to apply the adopted approach. The adopted approach allows a better representation of uncertainty and subjectivity of experts’ judgments. It would be of great interest, especially, when exact quantitative data are not available. A real case company example is exposed (automotive company) towards putting into practice the proposed approach.

Waste management is an unavoidable technological operation in the process of raw material extraction. The main characteristic of this technological operation is the handling of large quantities of waste material, which can amount to several hundred million cubic metres. Working with this amount of material usually requires high-capacity systems for excavation and loading, a large fleet of trucks for haulage, construction, and maintenance of a complex roads network, use of a significant area of land in order to achieve the required capacities, etc. At the same time, this operation must comply with all administrative and environmental standards. Therefore, optimising waste rock management (particularly haulage and dumping) has the potential to significantly improve the overall value of the project. This paper presents a hybrid model for the optimisation of waste dump design and site selection. The model is based on different mathematical methods (genetic algorithm, analytic hierarchy process and heuristic methods) adapted to different aspects of the problem. The main objective of the model is to provide a solution (in analytical and graphical form) for the draft waste dump design, on the basis of which the final waste dump design can be defined.

Most historical buildings and structures in Oman were built using unreinforced stone masonry. These structures have deteriorated due to ageing of materials, environmental degradation, and lack of maintenance. This research investigates the physical, chemical, and mechanical properties of local building materials and the results of an experimental study on the out-of-plane bending effectiveness of an innovative strengthening technique applied to existing masonry walls. The technique consists of the application on one face of the walls of a basalt textile-reinforced sarooj mortar (TRM). Four-point bending tests of full-scale masonry samples (1000 mm width, 2000 mm height, and 350 mm depth) were carried out using one unreinforced specimen and three different cases of reinforced specimens. The performance of unreinforced and reinforced specimens was analyzed and compared. The strengthened specimens were able to resist moments of out-of-plane bending 2.5 to 3 times greater than those of unreinforced specimen (160%- 233% increase). Moreover, the strengthened walls were able to sustain higher deformations (deflections) than the unreinforced specimen ranging from 20%-130%. The results showed that using TRM was effective for the out-of-plane strengthening of stone masonry using a local material (sarooj) that is compatible with existing stone masonry building materials.

In recent years, exterior-rotor brushless DC motors have become increasingly popular in robotics applications due to their compact shape and high torque density. However, these motors were originally used for continuous operation in drones. For applications such as exoskeletons, prostheses, or legged robots, short bursts of high power are often required. Unfortunately, vendors do not typically provide data on the motors' performance under these conditions. This paper presents experimental data on the torque-speed relationship, efficiency, and thermal responses of one of the most widely used outrunner-type brushless motors across its full operating range, including high-power, short-duration operation. The results of this study can inform the selection and design of actuators for a range of robotics applications, particularly those that require high power output for brief periods of time.

Today’s urban spaces face precipitous challenges and complications, which include the COVID-19 pandemic, urbanization, population growth, and climate change. Proximity plays an essential role in influencing the integrity of public spaces and urban environments, while proxemics studies people’s experience, and the benefits, of urban space, and is based on a behavioral system of activities that includes ‘territoriality’. There is a need to study the behavioural patterns of people in given situations with proxemic dimensions in order to sustain both human beings and the quality of urban space. However, people behave spontaneously within environmental settings and reflect each other’s responses, meaning it is important to distinguish between different cultures, which tend to respond in particular ways to the meaning of proximity. This suggests there is no universal indicator for phenomena such as crowding. The aim of this paper is to highlight the interrelationship between urban form and urban life. This study focuses on two patterns of activity - street life and social life - by adopting a descriptive-analytical approach to documentary and desk research. The findings reveal a vital distinction between social and public patterns of proximity, while other proximities, although critical, are not observed within interactions between people.

The Covid-19 pandemic and the subsequent implementation of lockdown measures have significantly impacted global electricity consumption, necessitating accurate energy consumption forecasts for optimal energy generation and distribution during a pandemic. In this study, we propose a new forecasting model called the Multivariate Multilayered LSTM with Covid-19 case injection ($\proposedModel$) for improved energy forecast during the next occurrence of a similar pandemic. We utilize data from commercial buildings in Melbourne, Australia during the Covid-19 pandemic to predict energy consumption and evaluate the model's performance against commonly used methods such as LSTM, Bi-LSTM, Linear Regression, Support Vector Machine and the previously published work of Multilayered LSTM (M-LSTM). The proposed forecasting model was analyzed using the following metrics of mean percent absolute error (MPAE), normalized root mean square error (NRMSE), and $R^2$ score values. The model $\proposedModel$ demonstrates superior performance, achieving the lowest MPAE values of 0.061, 0.093, and 0.158 for data sets from 3 different buildings, respectively. Our results highlight the improved precision and accuracy of the model, providing valuable information for energy management and decision-making during the challenges posed by the occurrence of a pandemic like Covid-19 in the future.

In metal continuous casting process is important to estimate the temperature evolution of casted section along machine from meniscus (point in which liquid metal is poured) to cutting machine where product is cut at commercial length. Particularly in the case of large sections, a convenient approximated model to achieve this goal with a feasible computational effort, is the so called travelling slice: the transversal section of casted product is subjected to different thermal boundary conditions (e.g. thermal flux, radiation, convection) that are found during the movement at constant speed from meniscus to the end of machine. In the case of an axisymmetric section, a comparison with the exact solution can be easily achieved. The article will show pros and cons of both, namely the far lower computational cost of travelling slice model without losing precision. Results confirm the validity of the travelling slice approach also at low casting speed and huge dimensions.

Quantum-dot cellular automata (QCA) are a promising nanoscale computing technology that exploits the quantum mechanical tunneling of electrons between quantum dots in a cell and electrostatic interaction between dots, in neighboring cells. QCA can achieve higher speed, lower power, and smaller areas than conventional complementary metal–oxide–semiconductor (CMOS) technology. Developing QCA circuits in a logically and physically reversible manner can provide exceptional reductions in energy dissipation. The main challenge of reversible QCA design is to maintain reversibility down to the physical level. The arithmetic logic unit (ALU) is an essential component of the central processing unit (CPU) of a computer. It performs various arithmetic and logical operations on the data that the CPU processes. Current QCA ALU designs are either irreversible or logically reversible; however, they lack physical reversibility, a crucial requirement to increase energy efficiency. In this paper, we present a novel multilayer design for a logically and physically reversible QCA ALU based on majority gates as the key components, which can perform 16 different operations. We use QCADesigner-E software to simulate and evaluate energy dissipation. The proposed logically and physically reversible QCA ALU offers an improvement of 88.8% in energy efficiency. Compared to the next most efficient 16-operation QCA ALU, this ALU uses 51% fewer QCA cells and 47% less area.

In recent years discrete element method (DEM) has gradually been applied to the traditional fluidization simulation of fine particles in micro fluidized bed (MFB). The application of DEM in simulating fast fluidization of fine particles in MFB has not yet received attention. This article presents a drag model that relies on the surrounding environment of particles, namely particle circumstance-dependent drag modle or PCDD model. Fast fluidization in MFB of fine particles is simulated using DEM based on the PCDD model. It is found that the gas-solid two-phase flow in MFB meets the common law of fast fluidization in circulating fluidized bed (CFB) to a certain extent, and also presents a special law that is significantly different from that in CFB. Simulations indicate that the local structure in MFB exhibits particle aggregation which is a natural property of fast fluidized, forming a structure where continuous dilute phase and dispersed concentrated phase coexist. The formation and fragmentation of particle clusters in different local regions of the bed have time synchronization. There exists strong effect of solid back-mixing in MFB, leading to relatively low outlet solid flux. The gas back-mixing effect is, however, not so distinct. The axial porosity shows a monotonically increasing distribution with the bed height, but does not strictly follow the single exponential distribution. The solid volume fraction at the bottom of the bed is significantly lower than the correlated value in CFB. The axial heterogeneous distribution of the cross-sectional average porosity in the lower half of the bed is also weakened. The radial porosity shows a distribution pattern of higher in the central region and lower in the sidewall region. Compared with the correlation results in CFB, the porosity near the central region in MFB is relatively low, while the porosity near the sidewall region is relatively high. The geometric size of the container, especially the radial size, is much smaller than that of a CFB. The relative area of contact between the MFB wall and particles is larger, and the wall friction factor becomes more significant. This may be the main reason for the time synchronization of particle agglomeration, severe particle back-mixing, low outlet solid flux, monotonically increasing axial porosity and weak core-annular structure of radial porosity.

The available direct gas dynamic tables provide the area ratio and the Prandtl-Meyer(P-M) angle of isentropic expansion of gas as functions of the Mach number. But finding the value of the Mach number in terms of area ratio or P-M angle requires an inverse function. Currently, the Mach number is determined by either interpolation from the direct gas dynamics tables, or the application of non-linear equation solvers using numerical methods. Both methods are approximate. In this paper inverse functions for Mach number in the form of Taylor’s series expansions are reported to develop the so-called inverse tables. The advantage of this approach is that the Mach number with a greater accuracy, referred to as nearly exact can be obtained by reading from the inverse table. In the presentation, the necessary equations and new tables that can be used by the scientific community will be disseminated. The data and computer programs are made available on GitHub through https://github.com/anillals/Inverse-gas-dynamic-tables- and-codes. A paper describing the complete mathematical steps in the derivation of the equations can be found at https://rdcu.be/dgrlf

To increase the power density of the electromechanical drive train of wind turbines, journal bearings can be used as planetary gear bearings instead of rolling bearings. This technological change presents new challenges. For example, wind turbine drive systems are subject to dynamic and low-speed operating conditions which can lead to an accelerated abrasive wear of the journal bearings. In addition, oil supply failure or peak loads due to wind gusts and grid and power converter faults could potentially result in catastrophic failure due to adhesive wear in a very short time. Such operating characteristics are, therefore, critical regarding the journal bearing wear lifetime and must be considered in the design. The successful implementation of journal bearings in wind turbines depends on a reliable estimation of adhesive and abrasive wear. In this paper, five different models for the wear calculation of journal bearings are evaluated regarding their suitability of wear calculation of planetary gear bearings in wind turbines. For this purpose, the following evaluation criteria were defined: parameter uncertainty, parametrization effort, in particular number of parameters, parameterization method and load case dependency of parameters and calculation effort. In order to be able to evaluate the wear models, the wear models are numerically implemented and the wear of a test journal bearing is exemplarily calculated under load conditions, which are comparable to load conditions in a wind turbine. Relevant influences from the wind turbine system such as lubricant, material and manufacturing dependent surface influences like roughness and hardness are considered. The wear models are evaluated with respect to their fulfillment of the defined criteria. The resulting evaluation allows the selection of a wear model that can be used to calculate the wear of planetary gear journal bearings in wind turbines, considering the available input variables.

As one of the main equipment of coal transportation, the belt conveyor with detection system is an important direction for the development of intelligent mine. The occurrences of non-coal foreign objects making contact with belts are common phenomenon in complex production environments and improper human operations. In order to avoid major safety accidents caused by scratches, deviation and breakage of the belt, a foreign object detection method is proposed for belt conveyor in this work. Firstly, a foreign object image dataset is collected and established, and IAT image enhancement module and attention mechanism of CBAM are proposed to enhance image data sample. Moreover, to predict the angle information of foreign objects with large aspect ratios, a rotating decoupling head is designed, and a MO-YOLOX network structure is constructed. Some experiments are carried out with the belt conveyor in the mine intelligent mining equipment laboratory, and the detections of different foreign objects are analyzed. Experimental results show that the accuracy, recall, and mAP50 of the proposed rotating frame foreign object detection method reaches 93.87%, 93.69%, and 93.72%, and the average inference time of foreign object detection is 25 ms.

The object of this paper is the analysis of isotropic rectangular thin plates supported (simply supported or clamped) along two opposite edges whereby the other edges have arbitrary support conditions; the plates are subjected to external bending moments, concentrated or distributed, and perpendicular to the supported edges. The standard approach to this problem is to replace the bending moment with a couple of forces infinitely close and to use the known expressions of efforts and deformations for the plate subjected to concentrated forces; the results are then related to the first derivatives of those efforts and deformations with respect to the position of application of the load. In this study, the external bending moment was expanded into a Fourier series, leading to a distributed external bending moment, and the boundary conditions and continuity equations were applied. Various types of rectangular plates were analyzed, as well as plates of infinite length whose results were identical to those in the literature. In addition, results for cantilever plates of infinite length were presented.

The main objective of the paper is to investigate the wave propagation behaviour in composites using numerical and experimental methods. Specifically, the study focuses on the actuation of waves by two PZT transducers placed on the surface and embedded at different positions within the composites, namely the quarter and middle positions. The numerical analysis provides simulated results, while the experimental analysis involves practical testing. The paper demonstrates that the numerical results are consistent with the experimental findings. It is observed that when the PZT transducers are placed at deeper positions within the composites, the peak amplitude of the first wave packet for the A0 mode decreases. Overall, the paper contributes to the understanding of wave propagation in composites by comparing the effects of different positions of PZT transducers, both on the surface and embedded within the material. The findings highlight the influence of transducer placement on wave characteristics, particularly the reduction in peak amplitude with deeper transducer positioning.

Hydrogen has been considered a future energy carrier for decades and the demand for hydrogen in refineries is always upward due to the revival of new technologies. The steam methane reforming method is frequently employed because of its high hydrogen generation efficiency at a cheap cost and minimal negative impact on the environment. But depending on the type of feedstock, one unit of hydrogen generate 9-10 units of CO2 that is needed to be treated for environmental sustainability. Therefore, the optimization of hydrogen production and CO2 capture is very important to address. The simulation research was conducted to anticipate and optimize steam reforming using Aspen HYSYS. A conversion-type reactor was used to develop this simulation-based model. The primary goal of this work is to investigate and optimize the production efficiency of hydrogen and the mitigation of CO2 that is generated from the steam reforming process by varying process parameters. CO2 capture efficiency was investigated at the different yields for hydrogen production and was found that a maximum of 98.8% of the CO2 can be absorbed using the proposed carbon capture system. Later, the Aspen Energy Analyzer tool revealed potential improvements for energy and cost optimization.

A macro network loading Model for multi-flow lines, time-varying and pedestrian congestion is proposed. The station hub is abstracted as a network of different types of nodes, and the flow of passengers at each node is calculated in real time for the purpose of simulating the hub's collection and distribution process. For correct transmission of passenger flow on heterogeneous networks, three types of indexes are proposed to distinguish the nodes, and then match the corresponding fundamental diagrams. This paper divides the update process of the dynamic network loading model into multiple processes by flow lines, and improves computational speed of DNL model. The proposed model is applied to the simulation of passenger flow collection and distribution in an actual hub station with multi-flow lines. The analysis results illustrate that the model can accurately reflect the realistic congestion facilities and explain the formation process of high-density areas. A rolling passenger flow control model based on optimal control theory is proposed. The effectiveness of the control model is verified based on simulation data.

Group-IV GeSn photodetectors (PDs) compatible with standard complementary metal-oxide-semiconductor (CMOS) processing have emerged as a new and non-toxic infrared detection technology to enable a wide range of infrared applications. The performance of GeSn PDs is highly dependent on the Sn composition and operation temperature. Here, we develop theoretical models to establish a simple rule of thumb, namely “GeSn-rule 23”, to describe GeSn PDs’ dark current density in terms of operation temperature, cutoff wavelength, and Sn composition. In addition, analysis of GeSn PDs’ performance shows that the responsivity, detectivity, and bandwidth are highly dependent on operation temperature. This rule provides a simple and convenient indicator for device developers to estimate the device performance at various conditions for practical applications.

Clean water is now very rare due to the increased water pollution causing many diseases. Heavy metals mainly lead from industrial waste i.e. batteries, cable sheaths, machinery manufacturing, shipbuilding, lead oxide and radiation protection is accountable & largely contributed lead in river and canal waters. Presence of lead in water is hazardous to life due to many reasons. It can cause cancer, weakness, anemia, kidneys, high blood pressure and nerve diseases. Inorganic lead is reported to me more dangerous than organic one. Industries including batteries, cable sheaths, machinery manufacturing etc. drains water that has soluble lead ranging from 200 – 500 mg/L. The safe limit of lead in water is about 0.015 mg/L. Pakistan is a country rich in minerals. It has about 3.5 MT of Kaolin (Clay) deposits situated at Nagar Parker region of Sindh, Pakistan. This indigenous material is being used to produce ceramic products and in paper making. Now we use this mineral source to remove lead from water by adsorption. Kaolin clay can be used as an adsorbent due to its unique structure. XRF technique is employed for clay characterization. Resultants will be analyzed by UV – Vis Spectrophotometry.

Considering that consumers are more willing to buy products online, companies are increasingly selling remanufactured products online through e-commerce platforms. Notwithstanding the high attention it elicits from researchers and companies, the study about the remanufacturing trading platform is in its infancy. Thus, we investigate 20 remanufacturing trading platforms related nowadays and make a gap analysis among them in terms of: (i) business model, (ii) product display, (iii) delivery products, (iv) quality assurance and after-sales service, (v) product review and star rate and (vi) transaction and payment. On this basis, we analyze features and trends for the development of remanufacturing trading platforms and propose six key applications aimed at filling the identified gaps. The consortium blockchain has the characteristics of security and transparency, high credibility, traceability and unfalsifiability, low cost, and strong scalability, which can provide effective support for the six key applications. Then, we construct the technical framework and the model of a consortium blockchain-supported remanufacturing trading platform. Further, we analyze the coupling mechanism between consortium blockchain and remanufacturing trading platform to explain how the remanufacturing trading platform supported by consortium blockchain achieves development characteristics. This study provides important guidance for the development, construction, and operation management of remanufacturing trading platforms.

This paper introduces an alternative method to design the path following controller of an under-actuated spherical mobile robot, which has a single pendulum structure its inside as a driving mechanism. The mechanism has an under-actuated problem; two inputs for the roll and pitch but no direct input for the yaw. In order to overcome this problem, the proposed method defines a virtual reference input for the heading direction. The virtual reference input works as a control input since it can be arbitrarily designed just like the reference input of a conventional system. The control scheme using the defined virtual reference input achieves the stabilization and path following control of the under-actuated spherical mobile robot without any additional control technique. The stability of the proposed control scheme is guaranteed by Lyapunov stability analysis, and simulation results are given to demonstrate its performance.

ORB (Oriented FAST and Rotated Brief) features are the most commonly used features in visual SLAM and visual odometry that have high computational speed, and rotation scale invariance. However, due to the homogenization of ORB features, the corner properties of specific features are poor in some artificial environments, and it can lead to poor matching performance when the environmental texture is not rich. The underlying reason is that the pixel grayscale changes in the less-richly textured regions on the image are not obvious, leading to a certain degree of mis-matching in the matching process. At the same time, when the camera motion speed is low, there is much overlap between adjacent frames. This results in minimal or almost no changes in the projection of feature points, and the system is highly sensitive to errors, In this case, even small errors can cause significant fluctuations in the calculation results. In response to the above issues, an improved feature point method for stereo vision mileage calculation is proposed to solve the problem of system stability deterioration when cameras move at low speeds in artificial envi-ronments. Firstly, weight calculation based on different texture regions is used to solve the problem of low corner properties of feature points caused by environmental texture differences. Then, keyframes are used for motion model estimation to improve the system's stability under low-speed motion. The experimental results of the dataset showed that the key frame rate was optimal between 10% and 12%, and the positioning accuracy was higher than these open-source systems compared with three common open-source VO systems.

Waste management is a significant issue that Indonesia must face. The presence of waste will always exist as long as life continues. One of the main challenges in waste management is the proper separation of organic and inorganic waste. As a solution to address this issue, the Ministry of Environment has made efforts to develop Waste Banks. However, it also creates new problems related to manual data collection, lack of monitoring by the community in implementing waste management activities, and a lack of specific reports regarding waste management conducted by officers. We propose the creation of a website using the Agile Development SDLC method. This website involve several steps and incorporate functions for data digitalization and expedited data collection, such as the addition of QR Code functionality, Monthly Reporting Function, and enhanced data security. The method used in this research is Agile Development. The application has been developed with a user-friendly interface and the latest web development technologies to ensure smooth performance. Overall, the web-based application for organic and inorganic waste using Laravel is an important step to promoting sustainable waste management practices.

The objective of this study is to investigate the use of excavation behavior prediction and analysis software in the field of civil en-gineering. PLAXIS and SoilWorks, widely used in the engineering and academic communities, were employed as research tools for analyzing gravel layers and deriving appropriate ranges of soil elastic modulus for different software programs. By collecting excavation cases in the Xindian area of New Taipei City, Taiwan, and conducting deep excavation analysis using the displacement of retaining walls, this study provides recommended ranges for localized selection of soil elastic modulus. The suggested range for PLAXIS is 7,840 N/m² to 9,800 N/m², while Soil-Works suggests a range of 2,450 N/m² to 3,430 N/m². These ranges allow for reasonable estimation of maximum deformations during the final excavation stage. Based on the research findings, it is recommended that engineers refer to the provided ranges when selecting soil elastic modulus for excavation analysis in gravel layers using different soft-ware programs in the Xindian area of Taiwan to improve the accuracy of deformation predictions during the final excavation stage. These results serve as important references for engineers and contribute to the effective prediction and management of excavation behavior in civil engineering projects.

In view of the limitations of the existing optimization method of suspender cable force, in order to improve the stress of suspender under completion state and avoid frequent adjustment of cable force and grid beam elevation during construction, a new method of cable force optimization is proposed. The article takes the longest large span arch bridge in the world, Pingnan Third Bridge, a Concrete-filled steel tube (CFST) arch bridge with a span of 575m as the engineering background combined with the finite element analysis and multi-objective optimization method. One cable force optimization method that suspender “Real-time correction during construction, in the process variable optimal and results reliable” during panel girder lifting of long span CFST arch bridges is clarified. Taking the panel girder weight and displacement during the construction as parameter variables, the displacement and unevenness of the panel girder under completion state as constraint conditions, the displacement and cable force during the hoisting construction as the objective equation, through the optimization of the objective equation, the suspender cable force and dis-placement of each hoisting section are calculated. The results show that it is feasible to introduce the optimization theory into the cable force optimization when lifting the panel girder. the segment displacement variation is minimized to meet the destination. The cable force distributed evenly under completion state of the bridge that further making sure the completion state satisfies the requirements. No repeating iteration is needed, thus avoiding cumberso me calculation, getting cable force once. With higher optimization efficiency and better effects, the method provides high value for the cable force calculation of same type bridge suspender construction and for guiding construction.

Onion is not just an edible food but its seeds can also be an important source of valuable oil with various sensitive applications mainly in pharmaceutical, cosmetic and food fields. This has encouraged the use of a supercritical fluid extraction in the present study to obtain oil from local onion seeds, hence avoiding even traces of organic solvents. For several advantages carbon dioxide at supercritical conditions was used as the fluid. The effects of four key operating parameters like pressure, temperature, particle size and CO2 mass flowrate were investigated in ranges of [150, 250 bars], [35, 65°C], [0.25, 0.85mm] and [50, 100g/min], respectively, using a Box-Behnken experimental design, for a constant extraction time of 3 hours. This led to optimal operating conditions of 250 bar, 57°C, 0.25mm and 50g CO2/min for the highest oil extraction yield value of 24.36%. Furthermore, gas chromatography-mass spectrometry (GC-MS) was used to identify qualitatively and quantitatively the chemical composition of the onion seed oils. About ten components were identified in the extracts, but with four major ones, namely 9,12-Octadecadienoic acid ,methyl ester, 9,12-Octadecadienoic acid (Z,Z)-,methyl ester, 9-Octadecadienoic acid (Z)-,methyl ester and Hexadecanoic acid, methyl ester, present with significant percentages, depending on the operating parameters values. These fatty acids are well known for their benefits for human health. Finally the study shows the importance and the merits of fluids when used under particular conditions of pressure and temperature, in very sensitive industrial fields.

This work aims to describe the dielectric behaviours of four main tissues in the human forearm using mathematical modelling, including fat, muscle, blood, and bone. Determining the electrical response of multiple tissues can help develop physiological monitoring of an organ or a body’s section by filtering out the impedance contributions from the surrounding tissues to blood flow-induced impedance variations. Multi-frequency bioimpedance analysis (MF-BIA) was initially performed using the finite element method (FEM) with a 3D forearm model followed by a pilot study to characterise the response of actual forearm tissues from 1 kHz to 349 kHz. Both the simulation and experimental results were fitted to a single-dispersion Cole model (SDCM) and a multi-dispersion Cole model (MDCM) to determine the Cole parameters for each tissue. The correlation analysis and Bland-Altman plot indicated a good fit between raw and fitted impedance values using both SDCM and MDCM. Overall, MDCM exhibited better performance in fitting and estimation of the Cole parameters with correlation coefficient (R2) of 0.99 and 0.97, root mean squared error (RMSE) of 0.09 Ω and 0.14 Ω, and mean difference (mean±standard deviation) of 0.00±0.09 Ω and -0.03±0.14 Ω for the real part and imaginary part of impedance, respectively.

The article reports on a patient who required a cranial protection system.Using additive manufacturing techniques and surgical planning with the help of bio-models, a patient-specific bone implant solution was proposed that allows aesthetic restoration of the affected area and provides an adequate level of protection. In addition, through a comparative analysis with finite elements, the mechanical response to external actions of the medical device, printed with two materials: polymethylmethacrylate (PMMA) and polyether-ether-ketone (PEEK), is simulated. The tested materials have recognized biocompatibility properties, but their costs on the market differ significantly. The results obtained demonstrate the similarities in the responses of both materials. It offers the possibility that low-income people can access these devices, guaranteeing adequate biomechanical safety, considering that PMMA is a much cheaper material than PEEK.

Infrared sensors incorporating suspended zinc oxide (ZnO) pyroelectric films and thermally-insulated silicon substrates are fabricated using conventional MEMS-based thin-film deposition, photolithography, and etching techniques. The responsivity of the pyroelectric film is improved through annealing at 500℃ for 4 h. The voltage response of the fabricated sensors is evaluated experimentally for a substrate thickness of 1 µm over a sensing range of 30 cm. The results show that the voltage signal varies as an inverse exponential function of the distance. A positioning system based on three infrared sensors is implemented in LabVIEW. It is shown that the position estimates obtained using the proposed system are in excellent agreement with the actual locations. In general, the results presented in this study provide a useful source of reference for the further development of MEMS-based pyroelectric infrared sensors.

This paper offers a set of comprehensive guidelines aimed at facilitating the widespread adoption of hydrogen in the industrial hard-to-abate sectors. The authors begin by conducting a detailed analysis of these sectors, providing an overview of their unique characteristics and challenges. The paper delves into specific elements related to hydrogen technologies, shedding light on their potential applications and discussing feasible implementation strategies. By exploring the strengths and limitations of each technology, the paper offers valuable insights into its suitability for specific applications. Finally, through a particular analysis focused on the steel sector, the authors provide in-depth information on the potential benefits and challenges associated with hydrogen adoption in this particular context. By emphasizing the steel sector as a focal point, the authors contribute to a more nuanced understanding of hydrogen's role in decarbonizing industrial processes and inspire further exploration of its applications in other challenging sectors.

Wastewater (WW) analysis is a critical step in various operations such as control of a WW treatment facility, and speeding-up the analysis of WW quality can significantly improve such operations. This work demonstrates the capability of neural network (NN) regression models to estimate WW characteristic properties such as biochemical oxygen demand (BOD), chemical oxygen demand (COD), ammonia (NH3-N), total dissolved substances (TDS), total alkalinity (TA), and total hardness (TH) by training on WW spectral reflectance in the visible to near-infrared spectrum (400nm-2000nm). The dataset contains samples of spectral reflectance intensity, which were the inputs, and the WW parameter levels (BOD, COD, NH3-N, TDS, TA, and TH), which were the outputs. Various NN model configurations were evaluated in terms of regression model fitness. The mean-absolute-error (MAE) was used as the metric for training and testing the NN models, and the coefficient of determination (R2) between the model predictions and true values was also computed to measure how well the NN models predict the true values. With online spectral measurements, the trained neural network model can provide non-contact and real-time estimation of WW quality at minimum estimation error.

The theory of fractional calculus extends the order of classical integer calculus from integer to non-integer. As a new engineering application tool, it has made many important research achievements in many fields, including image processing. This paper mainly studies the application of fractional calculus theory in image enhancement and denoising, including the basic theory of fractional calculus and its amplitude frequency characteristics, the application of fractional differential operator in image enhancement, and the application of fractional integral operator in image denoising. The experimental results show that the fractional calculus theory has more special advantages in image enhancement and denoising. Compared with the existing integer order image enhancement operators, the fractional differential operator can more effectively enhance the "weak edge" and "strong texture" details of the image. The fractional order integral image denoising operator can not only improve the signal-to-noise ratio of the image compared to traditional denoising methods, but also better preserve detailed information such as edges and textures of the image.

Hydrogen is believed to be the principal domain of sustainable energy drive as an alternative to fossil fuels. Unlike the existing standards and knowledge for other fuels, the integrity of sealing and storage materials under the hydrogen environment is not comprehensively studied due to the comparatively new technology and lack of standard laboratory protocols. Typically, storage and polymer materials used as sealing experience degradation and damage in different ways over time in the exposure of hydrogen at different operating conditions, called aging. Improved understanding of the physical and chemical mechanism of degradation due to gaseous hydrogen atmosphere; helps to select and develop the materials best suited to carrier and sealing for respective applications. Damage to materials from aging is inevitable in high-pressure hydrogen gas exposure. This review discusses the mechanism of different categories of aging of storage and sealing materials under the hydrogen environment. Also, the article approaches discussing different laboratory test methods for each type of aging simulation. It covers the limitation of current research on determining material integrity through existing techniques of aging experiments and also explores the latest development. Important improvements are suggested in terms of materials development and testing procedures to meet the existing knowledge in the literature.

A tumbler screen type residual film–impurity mixture wind separator as a key equipment for secondary utilization of farmland residual film. During the working process, the proportion of impurities in the separated waste mulch film intermittently increases, resulting in poor working stability of the device, which may hamper long-term operation. In this study, the material inside the separation unit was continuously monitored, and the main factor affecting separator per-formance was determined to be the challenges in the effective depolymerization of some residual film–impurity mixtures. The principles of agglomeration and depolymerization of the residual film–impurity mixtures were analyzed using computational fluid dynamics (CFD) and discrete element method (DEM) flow-solid coupling simulation methods. The key factor affecting the disaggregation of the mixture was the collision force between the residual film–impurity mixture and the trommel screen. The collision force was maximum when the residual film–impurity mixture first collided with the trommel screen when it was fed into the separation device. As determined by force analyses, the key factors affecting the collision force of the process were the material feeding amount and the structure of the inlet. Furthermore, simulations were carried out for different inlet structure forms; the evaluation index was the maximum collision force of the residual film–impurity mixture agglomerate on the trommel screen. The best disaggregation effect was obtained with a square feed inlet and at a feeding rate of 202 kg/h. A prototype was built using these specifications for verification. The average value of the ratio of impurities in the re-sidual film was 6.966%, the coefficient of variation was 7.38%, and the dispersion of statistical results was small. The ratio of impurities in the residual film was kept constant during the con-tinuous operation of the wind separator. Thus, this study analyzed the agglomerate disaggregation process and provided theoretical insights for deter-mining the optimal structures of the inlets of various cleaning devices and the feeding volumes.

Comminution is the most power-demanding stage, and the lack of geometallurgical testing, often for financial reasons, may result in an inefficient operation. The Geopyörä Rock Breakage test was developed with the objective of making mineral variability data more accessible by providing both standard comminution parameters and rock mechanical properties at low cost, and with a modest sample size, allowing a larger number of samples to be tested to reduce uncertainties and assure productivity. The objective of this work is to present the results of an extensive validation of this new rock breakage method against two of the main tests currently in use, namely the SMC® and Bond ball mill work index tests. More than 100 samples have been tested and the results compared, showing that the new method can accurately estimate the parameters of the traditional tests. This confirms that the new test is a reliable tool for comminution and geometallurgical tests.

This paper investigates the problem of cooperative standoff tracking using multiple fixed-wing unmanned aerial vehicles (UAVs) with control input constraints. In order to achieve accurate target tracking in the presence of unknown background wind and target motion, a coordinated standoff target tracking algorithm is proposed. The objective of the research is to steer multiple UAVs to fly a circular orbit around a moving target with prescribed intervehicle angular spacing. To achieve this goal, two control laws are proposed, including relative range regulation and space phase separation. On one hand, a heading rate control law based on Lyapunov guidance vector field is proposed. The convergence analysis show that the UAVs can asymptotically converge to a desired circular orbit around the target, regardless of their initial position and heading. Through rigorous theoretical proof, it is concluded that the command signal of the proposed heading rate controller will not violate the boundary constraint on heading rate. On the other hand, a temporal phase is introduced to represent the phase separation and avoid discontinuity of the wrapped space phase angle. On this basis, a speed controller is developed to achieve equal phase separation. The proposed airspeed controller met the requirement of airspeed constraint. In addition, to improve the robustness of the aircraft during target tracking, an estimator is developed to estimate the composition velocity of the unknown wind and target motion. The proposed estimator uses the offset vector between the UAV’s actual flight path and the desired orbit which is defined by Lyapunov guidance vector field to estimate the composition velocity. The stability of the estimator is proved. Simulations are conducted under different scenarios to demonstrate the effectiveness of the proposed cooperative standoff target tracking algorithm. The simulation results of indicate that, the temporal-phase-based speed controller can achieve fast convergence speed and small phase separation error. Additionally, the composition velocity estimator exhibits fast response speed and high estimation accuracy.

This paper discusses the use of networks of Inertial Measurement Units (IMU) for the reconstruction of trajectories from sensor data. Logistics is a natural application domain, to verify the quality of the handling of goods. This is a mass application and the economics of logistics impose that IMUs to be used must be low cost and use basic computational devices. The approach in the paper converts a strategy from the literature, used in the multi-target following problem, to reaching a consensus in a network of IMUs. The paper presents results on how to achieve the consensus in trajectory reconstruction, along with covariance intersection data fusion of the information obtained by all nodes in the network.

Switched-mode power supplies (SMPS) often utilize electrolytic capacitors due to their substantial energy density and economical pricing. However, their ability to function at low temperatures is essential for dependable operation in several sectors, including telecommunications, automotive, and aerospace. This study includes an experimental evaluation of how well standard SMPS electrolytic capacitors operate at low temperatures. This paper investigates the suitability of standard electrolytic capacitors used in switched-mode power supplies (SMPS) for low-temperature applications. The experimental evaluation exposed the capacitors to temperatures ranging from - 5 ∘C to - 40 ∘C, assessing capacitance (Cp), impedance (Z), dissipation factor (DF), and equivalent series resistance (ESR) at each temperature. The capacitor’s time-domain electrical signals were analyzed using the Pearson correlation coefficient to extract discriminative features. These features were input into an Artificial Neural Network (ANN) for training and testing. Results indicated a significant impact of low temperatures on capacitor performance. Capacitance decreased with lower temperatures, while ESR and leakage current increased, affecting stability and efficiency. Impedance proved to be a valuable diagnostic tool for identifying potential capacitor failure, showing a 98.44% accuracy drop at - 5 degrees and 88.75% at the peak temperature, indicating proximity to the manufacturer’s specified limit. The study suggests further research and development to improve electrolytic capacitors’ performance in SMPS systems under cold conditions to enhance efficiency and reliability.

To increase the efficiency of fuel processor and HT-PEMFC (High Temperature-Proton Exchange Membrane Fuel Cell) combined system, it is essential to improve the efficiency of a fuel processor. In this research, the fuel processor was simulated by Aspen Hysys® simulator, and effect of the various operating conditions on the total efficiency was investigated. Thermal efficiency of the fuel processor increased as the temperature and S/C (Steam to carbon) ratio increased, and the efficiency was higher at the S/C ratio of 3 than at the S/C of 4 at the reformer temperature of 700 ℃ and higher. Under the selected operating conditions of the fuel processor, recycling of unreacted hydrogen from the anode off gas (AOG) of the HT-PEMFC improve the overall efficiency of the combined fuel processer and HT-PEMFC by a factor of 1.28. Operating conditions where the AOG supplied excessive heat than required for fuel processor operation were excluded. The high-efficiency operating conditions of the fuel cell system were proposed with the target of 5 kW of output as the capacity of the household HT-PEMFC.

Nitrogen is crucial for plant physiology due to the fact that plants consume a significant amount of nitrogen during the development period. Nitrogen supports the root, leaf, stem, branch, shoot and fruit development of plants. At the same time, it also increases flowering. To monitor the vegetation nitrogen concentration, one of the best indicator developed in the literature is Normalized Difference Nitrogen Index (NDNI) which is based on the usage of the spectral bands: 1510 and 1680 nm. from Short-Wave Infrared (SWIR) region of electromagnetic spectrum. However, majority of the remote sensing sensors like cameras and/or satellites do not have a SWIR sensor due to the high costs. Many vegetation indexes like NDVI, EVI, MNLI, have been developed in also VNIR region to monitor the greenness and healthy of the crops. However these indexes are not very correlated to the nitrogen content. Therefore, in this study, a novel method is developed which transforms the estimated VNIR band indexes to NDNI by using a regression method between a group of VNIR indexes and NDNI. Training is employed by using VNIR band indexes as input and NDNI as output which are both calculated from the same location. After training, 0.93 correlation is achieved. Therefore, by using only VNIR band sensors, it is possible to estimate the nitrogen content of the plant with high accuracy.

Egyptians face a significant challenge in meeting the growing population's water needs for agriculture and food production. To address this, policymakers and researchers have implemented the National Great Project for Lining and Rehabilitation of All Open Canals of the Irrigation Network to reduce irrigation water losses through seepage, evaporation, and evapotranspiration. The current field study evaluates water losses from the Al Maanna canal network in Assiut governorate, Middle Egypt, using empirical formulas and field ponding methods. The obtained results indicated that the Moleth-Worth formula is more compatible and gives results that are in good agreement with the field measurements carried out. The estimated seepage losses from the existing, distorted Al Maanna canal network using the Moleth-Worth formula and field ponding method were about 2.07 and 2.20 million m3/month, respectively. Also, the calculated maximum evaporation and evapotranspiration losses were about 0.086 and 1.133 million m3/month, respectively. Consequently, the total water losses might be about 3.42 million m3/month, representing nearly 13.63% of the Al Maanna canal’s total discharge. After completing the lining process, seepage losses from lined canals were determined to be only about 0.472 million m3/month using the ponding method, while evaporation and evapotranspiration losses will be significantly decreased after canal rehabilitation. Hence, lining the Al Maanna canal network can decrease the total water losses by about 84%, which is sufficient to recommend and encourage the lining processes where the value of the gained quantities of water exceeds all the implementation expenses, in addition to other moral, cultural, and environmental gains.

The thermal properties of a building envelope are key indicators of the energy performance of the building. Therefore, methods are needed to determine quantities like U-values or heat capacitance in a fast, reliable way and with as little impact on the use of the building as possible. In this paper a technique is proposed that relies on a simplified electrical analogical model of building envelope components which can cover their dynamic thermal behavior. The parameters of this model are optimized to produce the best fit between simulated and measured outside surface temperatures. As the temperatures can be measured remotely with an infrared camera this approach requires significantly less installation effort and intrusion in the building than other methods. At the same time, a single measurement provides data for a large range of locations on a facade or a roof. The paper describes the method and a first experimental implementation of it. The experiment indicates that this method has the potential to produce results which have an accuracy that is comparable to standardized reference methods.

This paper presents the design of a miniaturized polyimide-based antenna for Ultra-Wideband (UWB) communication. Miniaturization is achieved through the utilization of adhesive material with a high dielectric constant (high-Dk). The goal of this work is to investigate the impact of such material on the antenna performance and to optimize its design for UWB operation. The manufacturing of the antenna using the proposed structure was developed and the prototype of antenna for UWB high-band (6 - 9 GHz) is measured and analyzed. By leveraging the high Dk of the adhesive material, the simulation and measurement results showed that the proposed antenna with high Dk adhesive film can achieve the compact dimension with good performance in gain, and time domain characteristics. The results of this study show a potential of exhibiting a reduction in the size of the antenna and will contribute to the advancement of miniaturized UWB antenna technology.

During normal ageing, physical changes take place, namely in terms of the biomechanical, musculoskeletal, and psychomotor systems, that reduce strength, flexibility, motor coordination, balance, and precision of movements. This article analyses the motion behaviour of a sample of 49 senior and pre-senior subjects during the process of entry to (ingress) and exit from (egress) new car models not experienced before, obtained over five days at the Geneva International Motor Show. The methodological process is based on visual studies using photography and video to analyse motion behaviour. This investigation identifies five entry movement strategies and three exit movement strategies in three types of vehicle groups. The movements adopted in the egress of the vehicle were more complex and difficult, in general, than those observed for ingress, requiring greater flexibility, agility/dexterity, and physical strength of subjects, involving more contact or support with vehicle parts. The main factor that influences movement strategies is essentially related to subjects’ levels of physical capacity and previous experiences. In conclusion, there are no significant changes in the subjects’ somatic movement strategies based on vehicle types.

Employing numerical methods to simulate manufacturing processes and study their influential factors is increasing. The development of computers and engineering software has increased the ability and accuracy of numerical methods in simulating various aspects of different processes. One of the manufacturing processes that has been considered by many industries in recent years to join metals in solid-state with unique properties is called friction stir welding. It is challenging and, in some cases, impossible to experimentally study the various aspects of this process, such as temperature distribution, stress distribution, and material flow, due to severe plastic deformation in the weld zone. In this case, numerical methods are used to investigate these parameters and better understand the process. This study first investigates various numerical methods researchers use to simulate the process. The ability, pros, and cons of these methods to simulate the process are also examined. Then, the applications of numerical models in simulating the temperature distribution during the process as well as the effects of input parameters on the temperature history of the process, are deeply considered. Next, the application of numerical methods in material flow modeling during the process is investigated. Finally, the modeling of the microstructure of the welding zone is investigated using numerical methods that help significantly in predicting the weld microstructure.

Aortic aneurysms (AA) occur in 4.8% of people causing 150,000 deaths annually. While endovascular aneurysm repairs reduce surgical morbidity, device-related failures (leak/displacement) are frequent highlighting the need for test models that better represent the mural geometry and compliance changes in human AAs. We aimed to develop and characterise an ex vivo porcine aortic model of AA. The optimal duration of tissue elastase exposure to emulate AA changes in elastin microstructure and content was determined using porcine aortic rings. Elastase-induced changes were quantified morphologically, and mechanical properties assessed via ring tensile testing. Subsequent experiments tested the potential for localised elastase treatment in a 1 cm segment of porcine aorta using a specially designed 3D printed test rig. The effect on pressure-diameter behaviour was investigated via inflation-extension testing. Elastase treatment produced time dependent decreases in elastin, resulting in an increased tensile modulus and circumferential length in the ring samples in the final phase of the J-shaped tissue stress-strain curves. In whole aortic segments, localised elastase-induced luminal degradation was successfully limited to a central region. The degree of elastin degradation achieved was sufficient to cause localised dilation with respect to controls under physiological pressures. Localised elastin degradation in porcine aortic segments is feasible and emulates the changes seen clinically in aortic aneurysms.

The dolomite dust-emulsified asphalt composite with excellent mechanical properties was successfully prepared using alkali activation. The effects of different alkali concentrations and emulsified asphalt contents on the mechanical properties of the materials were studied. The mechanical properties and microstructure of the composites were analyzed using compressive strength tests, bending strength tests, and SEM characterization. The experimental results show that the specimens have excellent mechanical properties: the 7-day compressive strength can reach 76.67 MPa, and the bending strength is about twice that of silicate-based geopolymer-emulsified asphalt composite. With an increase in emulsified asphalt content, the compressive strength of the samples decreases, while the bending strength increases first and then decreases. When the emulsified asphalt content is 1%, the bending strength of the sample is up to 28.81 MPa, which is 25% higher than that of the sample without emulsified asphalt. This indicates that an appropriate emulsified asphalt content can play a toughening role in the system, providing a new idea for designing high-toughness alkali-activated materials.

Intelligent transportation systems (ITS) are at the forefront of advancements in transportation, offering enhanced efficiency, safety, and environmental friendliness. To enable ITS, autonomous systems play a pivotal role, leveraging breakthroughs in autonomous driving, data-driven modeling, and multiagent control strategies to establish sustainable and coordinated traffic management. The integration of connected and automated vehicles has garnered significant attention as a potential solution for alleviating traffic congestion and improving fuel economy, achieved through global route optimization and cooperative driving. This study focuses on a predictive control perspective to address the cooperative cruise control problem. Online decision-making is employed during the driving process, utilizing information gathered from the network. By employing bargaining games to establish an operating agreement among vehicles, we formalize a synchronization approach based on predictive control theory. Ultimately, these findings are put to the test in an emulation environment within a hardware-in-the-loop system.

One main objective of this study was to increase the utilization of the raw material in the rose (Rosa damascena Mill.) essential oil industry by application of membrane technologies. A new ultrafiltration-based process for green recovery of polyphenols from distilled (de-aromatized) rose petals, the primary by-product in essential oil production, was created. The process includes enzyme-assisted extraction and subsequent membrane separation for partial concentration. Following a green membrane technology strategy, the newly developed process proposes an environmentally-friendly alternative to the conventional processing, comprising organic solvent ex-traction and adsorber resin purification. The results showed that the permeate flux decreased with volume reduction ratio’s rise and increased with the transmembrane pressure and feed flow rate rises. At the beginning of the process the highest flux was with UF1-PAN membrane, but at the end of the process with UF10-PAN membrane. Total polyphenols of the retentates in-creased by 27-39% and 26-67% during ultrafiltration with UF1-PAN and UF10-PAN membrane, respectively, with the highest value obtained for UF10-PAN membrane at VRR 6. The highest concentration factor and rejection of total solids, total polyphenols, redox-active antioxidants and radical scavenging antioxidants were obtained at VRR 6 with UF10-PAN membrane. This membrane and concentration level at transmembrane pressure of 0.4 MPa and feed flow rate of 330 dm3/h are recommended to be used for application of ultrafiltration of rose-petals by-product for potential use in the food industry.

The impact induced by cavitation bubble collapse can be utilized for mechanical surface treatment to improve fatigue properties of metals including additive manufactured metallic materials. A peening method using cavitation impact induced by a pulsed laser is called “laser cavitation peening (LCP)”. Normally, a Q-switched Nd:YAG laser, whose pulse width is a few nanoseconds, is used for LCP, which improves the fatigue strength. The problem with LCP is that the processing time is too slow. If a laser pulse whose pulse width is a few hundred microseconds can be utilized for LCP, the repetition frequency can be increased drastically using other types of laser systems such as a fiber laser. In the present paper, in order to reveal the possibility of LCP using a pulsed laser width of a few hundred microseconds, the use of LCP with a normal-oscillation Nd:YAG laser (pulse width ≈ 200 us) was investigated. It is demonstrated that LCP with the normal-oscillation Nd:YAG laser produced curvature in an aluminum alloy plate.

With the continuous improvement and observable benefits of electric vehicles (EVs), major logistic companies are introducing more EVs into their conventional fleets. This gives rise to a new type of vehicle routing problem with mixed vehicles, where heterogeneous internal combustion vehicles (ICVs) and electric vehicles are considered in route planning. In addition, certain deliveries that are not efficient on any type of vehicles, are outsourced to third-party common carriers. In this paper, we define this problem as a mixed vehicle routing problem with common carriers (MVRPC). The objective of such problems is to minimize the transportation costs by considering routes with ICVs and EVs, the possibility of visiting recharging stations, outsourcing options, and drivers’ layover regulations. This variant of the vehicle routing problems has many practical applications, particularly in the design of long-haul transportation and last-mile delivery services. Effective MVRPC solutions play a key role in promoting the going Green image and optimally allocating resources. The problem has received limited attention in the literature likely because addressing all the needed aspects is especially challenging. To solve the large-scale problem, we develop a branch-and-cut pricing framework that relies on strong cuts and customized labeling algorithms. Numerical experiments highlight the effectiveness of our algorithm. This success can be attributed to tailored critical resources, dynamically bounded bidirectional labeling procedures, strong dominance criteria, and implementation strategies.

The results of applying drilling engineering tools in planned deviated and horizontal wells of oil and gas condensate fields have been examined. The basis for the implementation of a comprehensive approach was the information obtained from drilling horizontal wells in the West and East Siberia, Volga-Ural region, and Iraqi Kurdistan. A synthetic model is considered as an example of the data, incorporating geomechanical and geological properties. As a result of the conducted audit of the geomechanical model and drilling process, the methodologies used were further developed to obtain optimal drilling fluid densities, aiming to prevent cavity formation on well walls, hydraulic fractures, and other related issues. The implementation of the Python programming language was introduced in the stages of geomechanical model preparation, resulting in a time acceleration of up to 20%. During the pre-drilling stage, technological operations were synchronized with the geomechanical model, increasing the involvement of process participants through the synchronization of knowledge areas. The interrelation between drilling technology, drilling parameters, properties of flushing fluids, and rock stability analysis was established, ensuring a 5% increase in construction speed (through NPT reduction and modification of existing tools and technological operations) and accident-free drilling of complex deviated and horizontal wells, provided that the recommended drilling parameters are followed.

To solve the problem of deformation and stress in segments when a full-face hard rock tunnel boring machine (TBM) tunnel for an urban subway passes through existing buildings, a three-dimensional mechanical calculation model of TBM tunneling under existing buildings was established based on numerical analysis to comprehensively study the spatial attributes of tunnel segments during TBM tunneling. The Qingdao Metro Line 1 TBM tunnel in the hard rock stratum of Xiaobei District passes through existing buildings. The results indicated that (1) the stress and deformation of the segments were different at different positions. The horizontal and vertical stress and displacement of the segments in front of the building were significantly affected by the building. When the segment was not in the area below the horizontal plane of the building, the vertical stress of the segment was significantly greater than the two stresses in the horizontal direction. (2) The vertical displacements of the vault and the arch bottom were the largest, and the influence of vertical accessories was stronger when the segment was closer to the building.(3) When the tunnel was excavated to approximately one tunnel diameter in front of the building, the building was affected. If the surrounding rock is unstable, the excavation face may collapse and the ground surface may sink, possibly leading to inclination, cracking, and uneven settlement of the building.

Recent years have seen a rapid uptake in distributed energy resources (DER). Such technologies pose a number of challenges to network operators, which can ultimately limit the amount of rooftop solar photovoltaics (PV) systems that can be connected to a network. The objective of this industry-based research was to determine the potential network effects of forecast levels of customer owned rooftop solar PV on Energy Queensland’s distribution network and formulate functions that can be used to determine such effects without the requirement for detailed network modeling and analysis. In this research, many of Energy Queensland’s distribution feeders were modelled using DIgSILENT PowerFactory and analyzed with forecast levels of solar PV and customer load. Python scripts were used to automate this process and quasi dynamic simulation (QDSL) models were used to represent the dynamic volt-watt and volt-var response of inverters, as mandated by the Australian Standard AS/NZS 4777. In analyzing the results, linear regression was used to form trend equations that represent various network characteristics against the number of PV connections. The trend equations provide a way of approximating network characteristics for other feeders under various levels of customer owned rooftop solar PV without the need for detail modeling.

Building Information Modelling (BIM) methodology have been optimizing the construction activity in all sectors: multidisciplinary designs development; construction planning and monitoring; building management and maintenance. A BIM environment aggregates several disciplines and different skillsets and in order to control and improve the quality of a BIM project, a BIM manager is required. The BIM manager has the responsibility to coordinate all tasks involved in a building design and associated activities usually workout over the project documents. The professional can access to various discipline models, located in a shared board, and request for amendments if inconsistencies are detected. The present study issue is illustrated with three building cases were distinct specific projects, disciplines and tasks were elaborated: collaboration between disciplines (architecture, structures and construction); structural analyses and reinforcement details; quantity take-off of materials and cost estimation; construction scheduling and simulation. Although there are limitations in the implementation of BIM methodology in all sectors and stages, within the construction industry, BIM have been bringing an important improvement in the quality of a building design, reflected in the quality of the final product. BIM methodology is a current demand in the construction industry supported on advanced technology and in an adequate management of projects, were the BIM manager has an important role.

Forest harvesting generates variable amounts of residue that represent a fire hazard and a hindrance to regeneration and must be managed accordingly. In South Africa, burning is the most common residue management method, but there is an interest in introducing safer and more effective techniques, such as mulching. For that reason, a productivity study was conducted in the Eastern Cape province to gather information on the productivity, cost, and work quality of the three main alternatives: manual broadcasting, manual broadcasting followed by mulching with an adapted farm tractor and mulching with a purpose-built mulcher. Manual broadcasting required 16 h/ha, mulching with a farm tractor 3.6 h/ha, and mulching with a purpose-built mulcher 0.9 h/ha (one pass). Manual broadcasting was the cheapest option, at a cost of 400 ZAR/ha. Mulching with a farm tractor and a purpose-built mulcher incurred a cost of 3 267 ZAR/ha and 4 083 ZAR/ha, respectively. Manual broadcasting achieved a minimal reduction of residue size, with 50% of the slash (branches and stem wood) having a mean length above 40 cm. When mulching with a farm tractor was applied, 49% of the slash (branches and stem wood) length reduced to about 30 cm. When a purpose-built mulcher was used, only 10% of the slash elements exceeded 40 cm length.

Plasma plays an important role in semiconductor processes. With the recent miniature and integration, the control of plasma became essential for the success in critical dimension of a few nanometers and etch narrow and deep holes with high aspect ratios. Recently, the etching process has reached physical limitations due to a significant increase in wafer surface temperature under the elevated amount of RF power, affecting not only the warpage phenomenon but also etching uniformity and etching profiles. Therefore, the plasma characteristics are identified using invasive single Langmuir probe (SLP) for wafer temperature diagnosis. Optical data is obtained through a non-invasive optical emission spectroscopy (OES) and the plasma parameters are derived to compare and verify with the SLP. Two variables, electron temperature and electron density, are substituted for the heat flux formula to derive the heat flux according to its location. Using a wafer-type temperature sensor, check the derived heat flux values and compare trends. Such studies are expected to be able to calculate heat flux values in real time, anticipate wafer temperatures, and solve existing problems.

The increased adoption of information and communication technology for smart grid applications will require innovative cyber-physical system (CPS) testbeds to support research and education in the field. The groundbreaking CPS testbeds with realistic and scalable platforms have progressively gained interest in recent years, with electric power flowing in the physical layer and information flowing in the network layer. However, CPSs are critical infrastructures and not designed for testing or direct training, as any misbehaving in an actual system operation could cause a catastrophic impact on its operation. Based on that, it is not easy to efficiently train professionals in CPSs. Aiming to support the advancement and encourage the training of industry professionals, this paper proposes and develops a complete testbed with commercial tools. The testbed can reliably replicate the performance of smart grid systems and the main potential cyber threats that electric grids may face. The complex interdependencies between the cyber and physical domains are discussed in detail, and different case scenarios are presented, providing insightful guidelines for key features and design decisions for future smart grid testbeds.

Spectrum distribution is a classical licensed spectrum accessing method in mobile communication networks. The licensed idle spectrum resources are authorized and distributed from spectrum owners to mobile users. However, the exponential growth of user capacity brings excessive load pressure on the traditional centralized network architecture. As lack of sufficient supervision and penalty measures, dishonest behaviors of spectrum owners and spectrum users will lead to the unfair status in the distribution process. As a result, the honest participants’ interest will be harmed. As an important supporting infrastructure of Internet of things technology, 6G cannot completely follow the existing spectrum distribution method. Towards 6G network spectrum distribution, an blockchain based licensed spectrum fair distribution method is proposed. A lightweight consensus mechanism named as proof of trust (PoT) is applied to reduce computational power consumption and consensus time overhead. We deploy the method on the Ethereum test chain, theoretical analysis and experimental results demonstrate the fairness, effectiveness and security of the method.

The established classical method of treating oil refinery effluent is flotation followed by biological treatment. Membrane bioreactors (MBRs) offer more advanced treatment, producing a clarified and potentially reusable treated effluent, but demand robust pretreatment to remove oil and grease (O&G) down to consistent, reliably low levels. An analysis of a full-scale conventional oil refinery ETP based on flotation alone, coupled with projected performance, energy consumption and costs associated with a downstream MBR, have demonstrated satisfactory performance of flotation-based pre-treatment. The flotation processes, comprising an API separator followed by dissolved air flotation (DAF), provided ~90% removal of both total suspended solids (TSS) and O&G coupled with 75% COD removal. The relative energy consumption and cost of the pretreatment, normalised against both the volume treated and COD removed, was considerably less for the API-DAF sequence compared to the MBR. The combined flotation specific energy consumption in kWh was found to be almost an order of magnitude lower than for the MBR (0.091 vs 0.86 kWh per m3 effluent treated), and the total cost (in terms of the net present value) around one sixth that of the MBR. However, the nature of the respective waste streams generated and end disposal of waste solids differs significantly between the pretreatment and MBR stages.