Summary Introduction: The psoas muscle index (PMI) and the skeletal mass index (SMI), as determined by computed tomography (CT), are the reference methods for assessing muscle mass. An alternative method is to measure the area of the rectus femoris muscle using ultrasonography (US).Objective : The objective of this study is twofold: firstly, to assess whether ultrasound imaging of the rectus femoris has an adequate correlation with psoas muscle index (PMI) and skeletal mass index (SMI) measurements obtained from computed tomography (CT) scans of oncosurgical patients at the L3 level; and secondly, to establish a cut-off point for diagnosing low muscle mass using this ultrasound technique. Material and methods: A retrospective cross-sectional observational study was carried out on oncosurgical patients referred to the nutrition consultation of the General University Hospital of Castellón over a four-year period. Malnutrition was diagnosed according to the GLIM criteria, muscle mass was assessed by ultrasound using a Mindray device, and skeletal muscle index (SMI) and appendicular skeletal muscle mass (PMI) were measured by computed tomography at the third lumbar vertebra (L3). Patients lacking a CT scan or with a CT scan performed more than one month after the ultrasound examination were excluded. Results: The study cohort comprised 43 patients (31 males), with a mean age of 64.7 ± 6.72 years, a mean BMI of 23.7 ± 4.31 kg/m², and a mortality rate of 25.6%. Most of the evaluations were conducted post-surgically (65.1%), with a notable prevalence of radical cystectomy and hepatic surgery. A total of 53 ultrasound evaluations were conducted, with an average area of 2.96 cm² [2.47-4.2] and adipose tissue of 0.55 cm [0.1-0.99] *. Additionally, computed tomography (CT) scans were performed to assess skeletal muscle mass (SMM) using the SMI/height method, yielding an average area of 38.4 cm² [31.6- 54.7)The median values for the variables were as follows: 272 [207-390] HU,PMI area of 4.31 m² [3.71-5.94] * and 86 [69-103] * HU density in PMI. All data were expressed as median and interquartile range. The Pearson correlation coefficients between US and SMI/height, SMI/height and PMI/height, and US and PMI/height were 0.70, 0.750, and 0.548, respectively. All these coefficients were statistically significant (p < 0.001). Following the established criteria for low muscle mass for SMI (1) and PMI (2), a ROC curve analysis was conducted on US, with a cutoff point for low muscle mass of 3.6 cm² , AUC 0.770 with 70% and specificity 100%.Respect PMI , the cut-off was 3.29 cm 2 and the area under the curve was 0.609, with a sensitivity of 42.55% and a specificity of 100%. Conclusions: The results of this study indicate that there is a significant correlation between SMI, PMI, and the area in cm² measured by US in the rectus femoris according to the protocol of García-Almeida et al. (3). The positive correlation between ultrasound and computed tomography (CT) imaging in our sample, which yielded comparable results to those reported by (4), suggests that ultrasonography may serve as a viable alternative to CT for the detection of low muscle mass. This study is the first to establish a cutoff point for ultrasonography in comparison to SMI and PMI. Further studies are required, utilising a semi-automatic method to circumvent measurement bias and encompassing a larger patient cohort, in order to detect cutoff points pre- and post-surgery for cystectomy and hepatic surgery, as well as cutoff points by sex.

Reiner Gamma is a potential target for low-orbiting spacecraft or even surface-landed missions in the near future. Unfortunately, thus far no comprehensive low altitude (below 20 km) or surface measurements of the magnetic field, magnetic source and plasma environment have been made post-Apollo to complement and complete our understanding of the solar wind interaction with lunar magnetic anomalies and swirl formation. Acquiring the detailed geological knowledge of the Reiner Gamma region is significant for the above scientific targets. In this study, the following research work in the lunar Reiner Gamma magnetic anomaly region was carried out for the regional geological investigation: (1) the topographic and geomorphologic analysis; (2) elements, minerals and sequence analysis; (3) 1:10,000 regional geological map analysis. Our work helps define measurement requirements for possible future low-orbiting or surface-landed missions to the Reiner Gamma area or similarly magnetized regions of the lunar surface.

The elevated environment temperature in summer plays adverse effects on bovine fertility. Antioxidant treatment may have positive impact to enhance oocyte competence could be possible strategy for alleviating the summer effects on bovine fertility. The present study was aimed to investigate the effects of exogenous melatonin treatment on oocyte development competence, blastocyst development rate, activity of antioxidant enzymes, expression profiles of development related genes and pregnancy rates in cattle during summer. The experiment was conducted in 44 non-lactating indigenous Sahiwal cattle divided into control and treatment group. Treatment group received (day 0) inj. Melatonin @ 18mg/50kg body weight while control group received inj. Corn oil, 4ml i.m. On day 4, all the cows were subjected to ovum pickup (OPU) to aspirate oocytes for in-vitro embryo production. Blood samples were used to determine lipid peroxidation (MDA) and antioxidant enzymes concentration (SOD, GSH), and also for plasma hormonal concentration analysis. The results revealed that blastocyst development rate (%) was higher in treatment group (p<0.05). Treatment group had increased (p<0.05) antioxidant enzymes (SOD and GSH), plasma melatonin and estradiol concentrations, and decreased (p<0.05) MDA concentrations than controls. The mRNA expression level of SOD2, HSPB1, BCL2, MT2 and STAR in oocytes, cumulus cells, COCs (immature and mature) and blastocyst were found to be higher, however, BAX was downregulated in melatonin-treated than control group. In conclusion, the results suggesting probable beneficial role of exogenous melatonin administration in reducing heat stress and enhancing blastocyst developmental competence in indigenous cattle.

Exosomes are produced by all cell types, their biogenesis is of endosomal origin, originating as a result of cell membrane invagination. Furthermore, physiochemical characteristics are important prerequisites for their commercial application. The representative size range of exosomes is 50-200 nm. Whereas, comparative to animal cell, exosomes from plant cell sources have a relatively larger size range, moreover, exhibit broader therapeutic potential. In this review study, we have briefly discussed the research potential of plant-derived exosomes. Including their earlier studies on biogenesis, characterization, isolation methods, and possible therapeutic applications. Additionally, we have quoted targeted drug delivery for targeted therapies and have provided insights of methods for customizing exosomes produced from plants with various drugs. Most-importantly, here we have embodied exosomes from plant sources are natural nano-inducers possessing the ability for inter-kingdom communication, resulting in cross-kingdom regulations.

The mutation in NF2 is the most common alteration associated with meningioma oncogenesis, and it is related to the loss of a suppressing protein called merlin. At the same time, alterations in energy production are visible in cancer cells where increased demand for energy is observed. Fatty acid oxidation could be one of the ways cancer cells obtain energy. This metabolic pathway uses the acylcarnitine shuttle system, which is responsible for the acylation of fatty acids and their transport through mitochondria. Therefore, this study aimed to profile acylcarnitines with short-, medium- and long-acyl chain length in meningiomas to assess their changes in tumors with different NF2 mutation statuses. For the analysis, solid-phase microextraction (SPME) coupled with liquid chromatography high resolution mass spectrometry (LC-HRMS) was used. The presented sampling method enables low invasive and easy collection of the analytes from the studied lesions, which can be crucial for future analysis of potential biomarkers in the surgery room. It was observed that higher levels of these analytes characterized meningiomas with NF2 mutation. Moreover, increased energy consumption and elevated levels of acylcarnitines show that these analytes can be considered as a marker of increased fatty acid oxidation in NF2 mutated cells.

This study addresses the importance of conducting mass movement susceptibility mapping and hazard assessment using quantitative techniques, including machine learning, in the Northern Lima Commonwealth (NLC). Previous exploration of the topographic variables revealed high correlation and multicollinearity among some of them, which led to dimensionality reduction through principal component analysis (PCA). Six susceptibility models were generated using weights of evidence, logistic regression, multilayer perceptron, support vector machine, random forest, and naive Bayes methods to produce quantitative susceptibility maps and assess the hazard associated with two scenarios: the first being an El Niño phenomenon and the second being an earthquake exceeding 8.8Mw. The main findings indicate that machine learning models exhibit excellent predictive performance for the presence and absence of mass movement events, as all models surpassed an AUC value of &gt;0.9, with the random forest model standing out. In terms of hazard levels, in the event of an El Niño phenomenon or an earthquake exceeding 8.8Mw, approximately 40% of the NLC area would be exposed to the highest hazard levels. It also highlights the importance of integrating methodologies to reduce model uncertainty, such as comprehensive analysis of variables supported by high quality data and organized workflows. The findings of this research are expected to serve as a supportive tool for land managers in formulating effective disaster prevention and risk reduction strategies.

Elizabethkingia anophelis is an opportunistic pathogen causing lifethreatening infections in humans, particularly in immunocompromised patients, neonates and elderly. Infections caused by this species are exceptionally challenging to treat due to its multiresistance to antimicrobials. We report a case of central line-associated bloodstream infection by E. anophelis in a 2.5-year-old girl with acute lymphoblastic leukemia successfully treated with a combination of piperacillin/tazobactam and amikacin. The literature was also reviewed on paediatric infections caused by E. anophelis. Accurate identification with MALDI-TOF, or using molecular techniques, is crucial because of varying susceptibilities among species. Early, accurate diagnosis and prompt effective treatment optimize outcomes.

SOC stock (SOCS) changes caused by land use changes are still unclear, and understanding this response is essential for many environmental policies and land management practices. In this study, we investigated the temporal-spatial and vertical distribution characteristics of SOCS on the Western Sichuan Plateau (WSP) using the sparrow search algorithm-random forest regression (SSA-RFR) models with excellent model applicability and accuracy. The temporal-spatial varia-tions in the SOCS were modeled using 1080 soil samples and a set of nine environmental covariates. We analyzed the effect of land use changes on the SOCS on the WSP. The total SOCS increased by 18.03 Tg C from 1990 to 2020. The results of this study confirmed that the SOCS in the study area has increased significantly since 2010, with an increase of 27.88 Tg C compared to the total SOCS in 2010. We found that the spatial distribution of the SOCS increased from southeast to northwest, and the vertical distribution of the SOCS in the study area decreased with increasing soil depth. Forest and grassland are the main sources of SOCS, the total SOCS in the forest and grassland accounted for 37.53 and 59.39% of the total SOC pool in 2020, respectively. Expansion of the wetlands, forest, and grassland areas could increase SOCS in the study area.

Introduction: Cleft lip with or without cleft palate (CL/P) is the most common congenital face anomaly in the world of multifactorial etiology. Objective: To determine the prevalence and characteristics of cleft palate. To identify associated risk factors to guide prevention and/or prenatal detection for early intervention and better health outcomes. To assess the rehabilitation protocols after operations in cleft palate. Design: Retrospective descriptive and clinical study. Patients: One hundred and three children with cleft palate treated in the Department of Head and Neck Surgery Clinic for Children and Young Adults, Department of Clinical Pediatrics, University of Warmia and Mazury, were included in the study. Methods: Records evaluation was conducted regarding sex, cleft type, mother occupation, parents education, histories of cleft in any of parents. The data were analyzed using R (R core team 2021) and the ordinal logistic regression analyses. Results: Children of stressed mothers during pregnancy had 9.4 times higher odds of having bilateral cleft. While there was no evidence that children sex, order of birth, and body mass as well as risk of maternal toxicity at work or reporting infections or drugs toxicity had a significant effect on the dependent variable. Conclusions: Children of parents with cleft history and having low educated mothers had higher probability of bilateral cleft palate. Children of stressed mothers during pregnancy had higher odds of having bilateral cleft. In literature, there is a lack of reports about rehabilitation in different operations methods in children with cleft palates.

In PVC compounds, hydrogen chloride plays a fundamental role in .H and .OH radical trapping lowering the flame energy during combustion. Furthermore, it yields actual Lewis acids promoting the cross-linking of the polyene sequences from PVC degradation and bringing a char layer, protecting PVC items from flames. Therefore, PVC is inherently flame retarded. However, plasticized PVC requires flame retardants and smoke suppressants to enhance fire performance. Low smoke acidity PVC compounds contain potent acid scavengers capable of acting at high temperatures. They react with hydrogen chloride in the condensed phase, making it unavailable in the gas and even in the condensed phase, compromising the reaction to fire and enhancing the smoke produced during the combustion. The effect of the sequestration of hydrogen chloride in PVC compounds for cables by potent acid scavengers has been studied in this paper through measurements of oxygen index, heat release, and smoke production. It is shown that potent acid scavengers strongly affect parameters like fire growth rate in cone calorimetry, specific (total) heat capacity, and specific heat of combustion of fuel gases in micro combustion calorimetry. They neutralize the action of antimony trioxide and Lewis acid precursors commonly used as flame retardants and smoke suppressants in PVC items, making them prone to ignite, release smoke, and spread flame. A new generation of flame retardants and smoke suppressants is necessary to keep low smoke acidity and high fire performances together in PVC items

The study presents the conceptual development and simulation of a robotic exoskeleton for ankle rehabilitation. The device is designed for ankle rehabilitation in patients with musculoskeletal disorders, injuries, or neurological diseases. The exoskeleton is equipped with three linear electric actuators that provide precise control of joint movements in multiple planes, allowing dorsiflexion and plantar flexion, inversion, and eversion. By utilizing a screw drive, the exoskeleton provides smooth and controlled movements, significantly reducing the risk of re-injury and improving rehabilitation. Simulation of the device and simulation results showed its high compatibility with the biomechanical features of the ankle joint. Virtual testing confirmed that the exoskeleton provides the smooth, controlled movements necessary for effective rehabilitation. Due to its ability to adapt to the individual physical capabilities of the patient, the device can be used in both active and passive forms of movement support. The results of the study demonstrate the potential of the exoskeleton in clinical applications, including its use in rehabilitation centers and at home. Its cost-effectiveness, ease of use, and high accuracy of movement control make this device a promising solution for restoring the functions of the lower extremities in patients with various musculoskeletal disorders.

The Lake Faro brackish basin (Sicily, Italy) was established Global Geosite as key locality of tectonic coastal lakes, but few were the research devoted this rare geological and ecological framework. To fill this gap, the main stratigraphical, sedimentological, ecological, morpho-bathymetric, and structural features were reported here first, linking geodiversity with biodiversity. In Lake Faro a shallow platform develops alongside a deep funnel–like shaped basin, reaching a maximum depth of 29 m. A NNW-SSE trending steep cliff, representing the abrupt transition from the platform to the basin, was interpreted as a dextral transtensive fault (Faro Lake Fault), presumably active since the late Pleistocene. The switches of the steep cliff NW-wards, acquiring a E-W trend, was interpreted as due to the occurrence of the Mortelle normal Fault, cut by the Faro Lake Fault. Abiotic bottom deposits consisted of coarse- to fine-grained quartzo–lithic rich sediments deriving from high grade metamorphic and igneous rocks, whereas the biotic component mainly consisted of bioclasts de-riving from clam farming actives for some centuries since today. The Quaternary shallow platform, from top to base includes: i) soft cover composed of coarse abiotic and prevalent biotic deposits; ii) hard conglomerates cemented by carbonates; iii) siliciclastic coarse deposits of the Messina Fm. In the deep basin, siliciclastic silty loams with minor amounts of biotic coarse deposits prevailed in the soft cover. The lake, exploited since the prehistoric age because of its high biodiversity and productivity, maintains some evidence of millennial relationships with the resident human cul-tures, there attracted by the favorable geomorphological and ecological peculiarities.

Soybean is the primary oilseed crop in the United States, with significant industrial value. Understanding the molecular mechanisms of heat stress tolerance in soybean is critical for developing stress-resistant cultivars. Current knowledge about the role of fatty acid desaturases (FADs) in modulating membrane fluidity under abiotic stress prompted this investigation into the impact of mutations in the FAD genes on seed germination from heat-stressed plants. In soybean, exposure to heat stress during anthesis is known to significantly reduce seed germination. In silico expression analysis indicated high levels of expression of the soybean FAD2 and FAD3 genes in leaves. Therefore, a detailed expression analysis of these genes was conducted using qRT-PCR from leaf tissue. Generally, downregulation of these genes was observed in the mutants; however, two genes, FAD3A and FAD2-3, showed a more than 2-fold increase in expression in six out of ten mutants under heat stress. This upregulation was particularly pronounced (7-fold) in mutant S17CR-170. Correlation analysis revealed a positive correlation (0.5) between the expression level of FAD3A, FAD3B, FAD3C, and FAD2-3 and the decline in germination from heat-stressed plants. This suggests these FAD genes may act as negative regulators of germination under heat stress conditions.

This article examines the complex interactions of the multiplier effect within the realm of tourism, with a specific emphasis on national parks. The main objective is to evaluate the multiplier effect within national parks, specifically focusing on Buiratau State National Nature Park in Kazakh-stan as a case study. The multiplier effect is a fundamental principle in the field of economic analysis. Economic multiplier effect is the term used to describe the occurrence when an initial infusion of spending in a certain industry leads to subsequent rounds of extra and sustainable economic activity. In the context of national parks, this phenomenon arises when visitor expendi-tures result in several favorable consequences, including increased employment, infrastructure advancement, and general economic expansion. The article seeks to measure the multiplier effect of tourism activities in Buiratau State National Nature Park through a thorough assessment. This entails examining several variables and datasets pertaining to visitor expenditure and its influ-ence. The study contributes to the existing literature by examining a recently constructed national park in a developing country. It compares the findings of this park with well-established national parks in other areas, emphasizing the distinct problems and opportunities it presents. Further-more, the research presents a methodological framework for evaluating the multiplier effect of national parks, which may be utilized in comparable contexts. This research ultimately enhances our comprehension of the economic implications of national parks and emphasizes their function as drivers for local and regional growth.

Trichiurus japonicus is the most productive fish caught in our country. In order to understand the seasonal distribution of Trichiurus japonicus in the central and southern parts of the East China Sea and Yellow Sea, three species distribution models were adopted, namely Random Forest Model, K-nearest neighbor algorithm and gradient ascending decision Tree model, based on the data of trawling surveys in the central and southern parts of the East China Sea and Yellow Sea from 2008 to 2009. Combined with variance inflation factor and cross-check, the distribution model of Trichiurus japonicus was screened and constructed to analyze the influence of environmental factors on the distribution of Trichiurus japonicus in the central and southern parts of the East China Sea and the Yellow Sea. The results showed that the random forest model had the advantages of fitting effect and prediction ability among the three models. The analysis of this model showed that the water depth, bottom water temperature and surface salinity had a great influence on the habitat distribution of Trichiurus japonicus. The relative resources of Trichiurus japonicus increased with the increase of bottom water temperature and reached the maximum at 23.8℃, and first increased and then decreased with the increase of water depth and surface salinity, reaching the maximum at 72 m and 31.2‰, respectively. The random forest model was used to predict the spatial distribution of Trichiurus japonicus in the East China Sea and the central and southern Yellow Sea during 2008-2009, and the results showed that the predicted results were close to the actual situation. The research results can provide reference for the exploitation and protection of Trichiurus japonicus resources in the East China Sea and the central and southern Yellow Sea.

The Songpan-Ganze Orogenic Belt (SGOB) is bounded by the South China, North China, and Qiang-tang blocks and forms the eastern margin of the Tibetan Plateau. The Tiechanghe granite is located at the junction of the southeast margin of the SGOB and the western margin of the Yangtze Block. To elucidate the genetic relationship between the Tiechanghe granite and the surrounding molybdenum deposits in Western Sichuan, in this study, we conducted U-Pb zircon and molybdenite Re-Os isotopic dating. The results indicate that the Tiechanghe granite predominantly consists of monzogranite, with minor occur-rences of syenogranite, while the molybdenum deposits are mainly found in skarn and quartz veins. The laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) U-Pb zircon ages of the Tiechanghe granite range from 162.9±0.7 Ma to 163.4±0.6 Ma, and the zircon LA-ICP-MS U-Pb age of the pegmatite veins is 164.1±0.9 Ma. These ages are consistent with the weighted average Re-Os age of the Ziershi molybdenite (160.3±1.6 Ma) within the error margins. These findings and previously ob-tained magmatic and metallogenic ages for the region suggest that a magmatic and mineralization event involving granite, molybdenum, tungsten, and copper occurred at around 162–164 Ma in the study area. This discovery broadens the exploration perspective for mineral resources in the Jiulong area of Western Sichuan and the entirety of Western Sichuan.

This study investigates cloud cavitation suppression around a model scale NACA66 hydrofoil using active water injection and explores the effect of multiple injection parameters. Numerical simulations and a mixed-level orthogonal test method are employed to systematically analyze the impact of jet angle αjet, jet location Ljet, and jet velocity Ujet on cavitation suppression efficiency and hydrofoil energy performance. The study reveals that jet location has the greatest influence on cavitation suppression, while jet angle has the greatest influence on hydrofoil energy performance. The optimal parameter combination (Ljet = 0.30C, αjet = +60 degrees, Ujet = 3.25 m/s) effectively balances energy performance and cavitation suppression, reducing cavitation volume by 49.34% and improving lift-drag ratio by 8.55%. The study found that the jet's introduction not only enhances vapor condensation and reduces the intensity of the vapor-liquid exchange process but also disrupts the internal structure of cavitation clouds and elevates pressure on the hydrofoil suction surface, thereby effectively suppressing cavitation. Further analysis shows that positive-going horizontal jet components enhance the lift-drag ratio, while negative-going components have a detrimental effect. Jet arrangements near the trailing edge negatively impact both cavitation suppression and energy performance. These findings provide valuable reference for selecting optimal injection parameters to achieve a balance between cavitation suppression and energy performance in hydrodynamic systems.

Drowsiness is a main factor for various costly defects, even fatal accidents in areas such as construction, transportation, industry and medicine, due to the lack of monitoring vigilance in the mentioned areas. The implementation of a drowsiness detection system can greatly help to reduce the defects and accident rates by alerting individuals when they enter a drowsy state. This research proposes an Electroencephalography (EEG) based approach for detecting drowsiness. EEG signals are passed through a preprocessing chain composed of artifact removal and segmentation to ensure accurate detection followed by different feature extraction methods to extract the different features related to drowsiness. This work explores the use of various machine learning algorithms such as Support Vector Machine (SVM) the K Nearest Neighbor (KNN) the Naive Bayes (NB) the Decision Tree (DT) and the Multilayer Perceptron (MLP) to analyze EEG signals sourced from the DROZY database, carefully labeled into two distinct states of alertness (awake, and drowsy). Segmentation into 10-second intervals ensures precise detection, while a relevant feature selection layer enhances accuracy and generalizability. The proposed approach achieves high accuracy rates of 99.84% and 96.4% for intra (subject by subject) and inter (cross-subject) modes, respectively. SVM emerges as the most effective model for drowsiness detection in the intra mode, while MLP demonstrates superior accuracy in the inter mode. This research offers a promising avenue for implementing proactive drowsiness detection systems to enhance occupational safety across various industries.

Introduction: The Severe Acute Respiratory Syndrome Coronavirus 2 (SARS-CoV-2) infection may cause acute respiratory failure but also remains responsible for many other pathologies, including electrolyte disorders. SARS-CoV-2 infection can cause dysfunction of the renin-angiotensin-aldosterone system and disrupt water hemostasis with thirst and appetite abnormalities. Dysnatremia affects prognosis and may be associated with mortality in patients admitted to SARS-CoV2 intensive care. Patients and Methods: The study included 209 patients admitted to the Intensive Care Unit between April 12, 2021, and March 1, 2022 who were over 18 years old and diagnosed with SARS-CoV-2 infection by clinical and thoracic tomography findings or with a positive reverse transcription polymerase chain reaction (RT-PCR) test result. The laboratory markers, treatment modalities, nutritional, and respiratory support also for outcome evaluation, length of stay in the ICU, total hospitalization duration, and mortality in ICU were recorded.The laboratory marker comparison was made admission with the final assessment performed before the time of mortality in ICU or discharge. Results: Inotropic requirements among patients were high which was reflected in the first-month mortality. Hypernatremia presence was associated with an increase in enteral support and inotropic support requirement and mortality. Hypernatremia was correlated with diabetes mellitus, chronic renal failure, and a longer duration under mechanical ventilation. Discussion: Hypernatremia was an important risk factor in ICU patients hospitalized for SARS-CoV-2 infection, which was also affected by the treatment regimens given itself. This complex relationship underlies the importance of proper electrolyte management, especially in patients who were under severe stress and organ failure.

The high flammability and lack of charrability of polystyrene (PS) pose significant limitations on its broader applications. Therefore, there is an urgent need for a straightforward and efficient method for the synthesis of flame-retardant PS, which still poses a considerable challenge. In this study, we present an efficient approach to enhance the flame-retardant properties of PS through direct phosphorylating aromatic C(sp2)-H bonds using commercially available and inexpensive manganese catalyst. A range of phosphonates served as reactive substrates to enable a tunable degree of polymer functionalization. The corresponding phosphorylated PS specimens were determined by means of 1H NMR, 31P NMR, FTIR spectroscopy and GPC. Microscale combustion calorimetry (MCC) tests indicate that this protocol indeed enhances the flame-retardant performance of PS. Moreover, other advantages associated with the incorporation of the phosphonate group have been observed, including improved thermal resistance and wettability. This cost-effective strategy of Mn-catalyzed C-H can also be utilized to directly obtain phosphonate modification of waste foamed PS and styrene acrylonitrile copolymer, providing a new method for the purpose of recycling and upgrading PS plastics.

A new quinazolinone alkaloid, named peniquinazolinone A (1), as well as eleven known com-pounds, 2-(2-hydroxy-3-phenylpropionamido)-N-methylbenzamide (2), viridicatin (3), viridicatol (4), (±)-cyclopeptin (5a/5b), dehydrocyclopeptin (6), cyclopenin (7), cyclopenol (8), methyl-indole-3-carboxylate (9), 2,5-dihydroxyphenyl acetate (10), methyl m-hydroxyphenylacetate (11), conidiogenone B (12), was isolated from the endophytic Penicillium sp. HJT-A-6. The chemical structures of all compounds were elucidated by comprehensive spectroscopic analysis, including 1D, 2D NMR, and HRESIMS. The absolute configuration at C-13 of peniquinazolinone A (1) was established by applying the modified Mosher’s method. Compounds 2, 3, and 7 exhibited an op-timal promoting effect on the seed germination of Rhodiola tibetica at a concentration of 0.01 mg/mL, while the optimal concentration for compounds 4 and 9 to promote Rhodiola tibetica seed germination was 0.001 mg/mL. Compound 12 showed optimal seed-germination-promoting activity at a concentration of 0.1 mg/mL. Compared with the positive drug 6-benzyladenine (6-BA), compounds 2, 3, 4, 7, 9, and 12 could extend the seed-germination period of Rhodiola tibetica up to the 11th day.

The branch prediction units (BPUs) generally have security vulnerabilities, which can be used by attackers to obtain the execution status, jump directions, and jump address of conditional branches, and the existing protection methods cannot defend against these attacks. Therefore, this article proposes a hardware security protection method for conditional branches of embedded systems. This method calculates the number of updates to the branch target buffer (BTB). When it exceeds the threshold, BTB is locked to prevent attackers from analyzing the execution status of branches based on the time difference of whether BTB is updated. Moreover, the hybrid physical unclonable function (PUF) circuit is designed to provide confidentiality protection for the jump directions, jump addresses, and their indexes, preventing attackers from stealing these critical data. If these mechanism fails and attackers successfully tamper with conditional branches, this paper proposes a control flow integrity (CFI) protection mechanism based on branch labels to timely detect tampering with instruction codes, jump addresses, and jump directions. The proposed method is implemented and tested on FPGA. The experimental results show that this method can achieve fine-grained security protection for conditional branches, with about 5.4% resource overhead and less than 5.5% performance overhead.

Mannosylerythritol lipids (MELs), one of the most promising biosurfactants (BS), are glycolipids produced by yeasts or fungi, with great environmental performance and a high compatibility with the human body. MELs besides working as typical surfactants, can form diverse structures when in the critical aggregation concentration (CAC), reducing the surface tension of water and other solutions, and being stable over a wide range of conditions. Among others, MELs present anti-microbial, antitumor, antioxidant and anti-inflammatory activity, skin and hair repair capacity, which opens possibilities for their use in applications from cosmetics and pharmaceutics to bio-remediation and agriculture. However, their market share is still low when compared to other glycolipids, due to their less developed production process and higher production cost. This re-view gathers information on the potential applications of MELs mentioned on the literature since 1993. Furthermore, it is also explored the current strategies being developed to enhance the market presence of MELs, in parallel with the ones developed for rhamnolipids and sophorolipids.

The wellness economy has developed rapidly recently, particularly in wellness tourism. Wellness tourism transforms sustainable strategy through the availability of extended multi-actor engagement in service innovation to further the tourism experience. Therefore, when operating a wellness tourism destination, it is necessary to encourage multi-actor engagement in service innovation to achieve sustainable development. This paper introduces a mixed research method with the SWOT-AHP-QSPM, as it qualitatively analyzes the advantages, disadvantages, opportunities, and threats, constructs an evaluation index system, conducts quantitative analysis using the analytic hierarchy process, determines the index weight and weighted score, and calculate the sustainable development strategy, which is appropriate for wellness development of Chongqing Tea Mountain and Bamboo Forest National Forest Park. Purposive field surveys and personal interviews were conducted in Chongqing forest tourism destinations, involving 356 effective respondents. The research reveals that multi-actor engagement significantly enhances sustainable development. These findings bridge service innovation knowledge gaps and provide valuable insights for forest tourism destination management and sustainable policy strategies to elevate multi-actor engagement in forest sites.

This study aimed to evaluate the impact of Candida albicans on subgingival biofilm formation on dental implant surfaces. Scanning electron microscopy (SEM) and confocal laser scanning microscopy (CLSM) were used to compare biofilm structure and microbial biomass in the presence and absence of the fungus after periods of 24, 48, and 72 h. Quantitative polymerase chain reaction (qPCR) was used to quantify the number of viable and total micro-organisms for each of the biofilm-forming strains. A general linear model was applied to compare CLSM and qPCR results between control and test conditions. The biofilm developed with C. albicans at 72 h had a higher bacterial biomass, with a significantly higher cell viability (p &lt; 0.05). After both 48 and 72 h of incubation, in the presence of C. albicans, there was a significant increase in counts of Fusobacterium nucleatum and Porphyromonas gingivalis and in the cell viability of Streptococcus oralis, Aggregatibacter actinomycetemcomitans, F. nucleatum, and P. gingivalis. Using a dynamic in vitro multispecies biofilm model, C. albicans exacerbated the development of the biofilm grown on dental implant surfaces, significantly increasing the number and cell viability of periodontal bacteria.

Lignin fibers typically influence the mixture performance of stone matrix asphalt (SMA), such as strength, stability, durability, noise level, rutting resistance, fatigue life, and water sensitivity. However, limited studies were conducted to analyze the influence of fibers on the percent voids in mineral aggregate in bituminous mixture (VMA) during the mixture design. This study analyzed the effect of different fibers and fiber contents on the VMA in SMA mixture design. A surface-dry condition method test and Marshall Stability test were applied on the SMA mixture with four different fibers (i.e., flocculent lignin fiber, mineral fiber, polyester fiber, blended fiber). The test results indicated that the bulk specific gravity of SMA mixtures and asphalt saturation decreased with the increasing fiber content, whilst the percent air voids in bituminous mixtures (VV), Marshall Stability and VMA increased. Mineral fiber had the most obvious impact on the bulk specific gravity of bituminous mixtures, while flocculent lignin fiber had a minimal impact. The mixture with mineral fiber and polyester fiber had significant effects on the volumetric properties, and, consequently, exhibited better VMA over the conventional SMA mixture with lignin fiber. Modified fiber content range was also provided, which will widen the utilization of mineral fiber and polyester fiber in the applications of SMA mixtures. The mixture evaluation suggested no statistically significant difference between lignin fiber and polyester fiber on the stability. The mineral fiber required a much larger fiber content to improve the mixture performance than other fibers. Overall, the results can be a reference to guide SMA mixture design.

In this paper, a semi-empirical model of air waves induced by falling rock is described. The model is composed of a uniform motion phase (velocity close to 0 m·s^-1) and an acceleration movement phase. The uniform motion phase was determined based on experimentally and the acceleration movement phase was derived by theoretical analysis. A series of experiments were performed to verify the semi-empirical model and elucidated the law of the uniform motion phase. The acceleration movement phase accounted for a larger portion with a greater height of the falling rock. Experimental results of different falling heights of the goaf showed close agreement with theoretical analysis values. The semi-empirical model could accurately and conveniently estimate the velocity of air wave induced by falling rock. Thus, the semi-empirical model can provide a reference and basis for estimating the speed of air waves and designing protective measures in mines.

Background/Objectives: The pediatric definition of severe obesity (OB) depends on the body mass index (BMI) references. We evaluated different BMI derived metrics of the World Health Organization (WHO) system to define which cut-off is associated with the highest cardiometabolic risk (CMR); Methods: In this multicentric study data were obtained by 3727 youths (1937 boys; 2225 children, 1502 adolescents. severe OB was defined as BMI &gt;99th percentile (BMI99), BMI97 ≥120% or BMI Z-score &gt; 3 (WHO tables). The continuous CMR Z-score (sum of residual standardized for age and sex of waist-to-height ratio, systolic and diastolic blood pressure, triglycerides, and HDL-Cholesterol x -1) and the cluster of at least two CMR factors (hypertension, high triglycerides, low HDL-Cholesterol and high waist-to-height ratio) were calculated; Results: Continuous CMR Z-score was significantly higher both in children or adolescents with severe OB defined by 120% BMI97 compared to BMI &gt;99th (p &lt;0.0001), while it was lower only in adolescents with severe OB defined by 120% BMI97 compared to BMI Z-score &gt;3 (p &lt;0.0001). Compared to BMI97 ≥120%, BMI Z-score &gt;3 had higher specificity, but lower sensitivity in identifying children and adolescents with clustered CMR factors; Conclusions: The definition of severe OB based on BMI97 ≥120% is superior to BMI99 but it is inferior to BMI Z score &gt;3 as far as the association between severe OB and CMR factors is concerned. Pediatricians should take into consideration the implications of the use of different BMI metrics in those countries that recommend the WHO system.

The efficient preparation of single-stranded DNA (ssDNA) rings, as a macromolecular construction approach with topological features, has aroused much interest due to their numerous applications in biotechnology and DNA nanotechnology. However, an extra splint is essential for enzymatic circularization, and by-products of multimers are usually present at high concentrations. Here, we proposed a simple and robust strategy of using permuted precursor (linear ssDNA) for circularization by forming an intramolecular dynamic nick using a part of the linear ssDNA substrate itself as the template. After the simulation of the secondary structure for desired circular ssDNA, the linear ssDNA substrate is designed to have its ends on the duplex part (≥5 bp). By using this permuted substrate with 5'-phosphate, the splint-free circularization is simply carried out by T4 DNA ligase. Very interestingly, formation of only several base pairs (2–4) flanking the nick is enough for ligation, although they form only instantaneously under ligation conditions. More significantly, the 5 bp intramolecular duplex part commonly exists in genomes or functional DNA, demonstrating the high generality of our approach. Our findings are helpful for understanding the mechanism of enzymatic DNA ligation from the viewpoint of substrate binding.

For monitoring of chimeric antigen receptor (CAR) T-cell therapies antigen-based CAR detection methods are usually applied. However, for each target-antigen a separate detection system is required. Furthermore, when monitoring CAR T-cells in the blood of patients treated with bispecific antibodies or T-cell engagers (bsAbs/BiTEs) recognize the same antigen, these methods producing false-positive results in clinical diagnostics. Anti-CAR-linker monoclonal antibodies (mAbs) targeting the linker sequence between the variable domains of the antigen binding CAR fragment, promise an universal and unbiased CAR detection. To test this, we analyzed clinical specimens of all BCMA- and CD19 targeting CAR T-cell products currently approved for clinical use. We found a highly specific and sensitive CAR detection by using anti-CAR-linker mAb in blood cells from patients treated with Ide-cel, Tisa-cel, Axi-cel, Brexu-cel, and Liso-cel. For Ide-cel and Tisa-cel the sensitivity was significant lower compared to antigen-based CAR detection assays. Strikingly, the specificity of anti-CAR linker mAb was not affected by the simultaneous presence of bispecific blinatumomab or teclistamab for Axi-cel, Brexu-cel, Liso-cel or Ide-cel, respectively. Cilta-cel (containing an monomeric G4S-CAR linker) could not be detected by anti-CAR linker mAb. In conclusion, anti-CAR-linker mAbs are highly specific and useful for CAR T-cell monitoring but not universal applicable.

Bacteriophages (phages) are potential alternatives to chemical antimicrobials against pathogens of public health significance. Understanding the diversity and host specificity of phages is important for developing effective phage biocontrol approaches. Here, we assessed the host range, morphology, and genetic diversity of eight Salmonella enterica phages isolated from a wastewater treatment plant. The host range analysis revealed that six out of eight phages lysed more than 81% of the 43 Salmonella enterica isolates tested. The genomic sequences of all phages were determined. Whole genome sequencing data (WGS) data revealed that phage genome sizes ranged from 41 to 114 kb with GC contents be-tween 39.9 and 50.0 %. Two of the phages SB13 and SB28 represent new species Epsep-timavirus SB13 and genera Macdonaldcampvirus, respectively as designated by the In-ternational Committee for the Taxonomy of Viruses (ICTV) as per genome based taxonomic classification. One phage (SB18) belonged to the Myoviridae morphotype while the re-maining phages belonged to the Siphoviridae morphotype. The gene content analyses showed that none of the phages possessed virulence, toxin, antibiotic resistance, type I-VI toxin-antitoxin modules or lysogeny genes. Three (SB3, SB15 and SB18) out of the eight phages possessed tailspike proteins. Whole genome-based phylogeny of the eight phages with their 113 homologs revealed three clusters A, B, C and seven subclusters (A1, A2, A3, B1, B2, C1 and C2). While cluster C1 phages were predominantly isolated from animal sources, cluster B contained phages from both wastewater and animal sources. The broad host range of these phages highlights their potential use to control the presence of S. enterica in foods.

A low-cost bio-mass-derived carbon substrate has been employed to synthesize MoS₂@carbon composites through a hydrothermal method. Carbon fibers derived from natural cotton provide a three-dimensional and open framework for the uniform growth of MoS₂ nanosheets, thus constructing hierarchically coaxial architecture. The unique structure could synergistically benefit fast Li-ion and electron transport from the conductive carbon scaffold and porous MoS₂ nanostructures. As a result, the MoS₂@carbon composites, when served as anodes for Li-ion batteries, exhibit a high reversible specific capacity of 820 mAh g^-1, high-rate capability (457 mAh g^-1 at 2 A g^-1), and excellent cycling stability. The superior electrochemical performance makes the MoS₂@carbon composites to be low-cost and promising anode materials for Li-ion batteries.

Drought presents significant challenges in arid regions, adversely impacting agriculture, water resources, and ecosystems. In Xinjiang, Northwest China, although large-scale climatic phenomena are well studied, finer-scale climatic variability in subregions such as the Ili River Valley (IRV) remains understudied. This knowledge gap impairs effective agricultural planning and environmental management in this ecologically fragile but agriculturally important region. In this study, we analyze the spatiotemporal evolution of drought in the IRV from 1961 to 2023, using data from ten meteorological stations. We applied the SPEI drought Index alongside Sen's trend analysis, the Mann-Kendall test, the cumulative departure method, and wavelet analysis to examine drought patterns. Results indicate significant drying trends in the IRV beginning in 2005, with frequent drought events from 2015 onwards, and 2019 marking a key transition from wet to dry conditions. The overall drought rate was -0.09/10a, suggesting a milder drought severity in the IRV compared to broader Xinjiang. Seasonally, the IRV experiences drier summers and wetter winters relative to the region's averages, with negligible changes in autumn and milder drought conditions in spring. Abrupt changes in drying seasons occurred later than in Xinjiang, with delays of 5, 21, and over 37 years for spring, summer, and autumn, respectively, indicating a lagging response. Spatially, the western plains are more prone to aridification than the central and eastern mountainous regions. significant differences in drought cycles, longer than those in Xinjiang, with distinct wet-dry phases observed over multiple time scales and across seasons highlighting the complexity of drought variability in IRV. In conclusion, the Vally exhibits unique drought characteristics, with milder intensities, pronounced seasonal variation, spatial heterogeneity, and notable resilience to climate change. These findings emphasize the necessity of region-specific drought management strategies, as those effective on a larger regional scale may not be suitable for subregions.

In the midst of the push for dual-carbon goals, urban centers are faced with the imperative of reducing emissions and conserving energy, while rural regions are harnessing their abundant new energy resources to promote balanced urban-rural development. Photovoltaic (PV) power generation, known for its cleanliness, safety, and emission-free nature, is playing a crucial role in the evolution of Henan Province's power supply industry. This paper delves into the current state of Henan's power supply infrastructure, the trajectory of its low-carbon development, and the policies shaping the PV sector. It also examines the establishment of an urban-rural mutual aid model through the lens of alternative energy technologies. By utilizing a combination of case studies and systematic theoretical research, this paper uncovers the untapped economic potential of new energy sources in rural areas and presents strategies for synergistic development in alignment with dual-carbon goals within the power supply industry. The research underscores the significance of an urban-rural mutual assistance model in achieving carbon neutrality, addressing urban-rural development gaps, fostering shared prosperity, and contributing Chinese insights to global climate governance frameworks.

One of the factors leading to the slow decline in poverty in Indonesia is the lack of government at-tention to reduce income inequality. Fiscal policy and economic growth can effectively reduce poverty after lowering income inequality, so the inequality channel must be considered. Socioec-onomic and infrastructure differences between provinces can influence the effectiveness of eco-nomic growth and fiscal policy in reducing poverty. This study aims to assess the effects of eco-nomic growth and fiscal policy on spending and taxes on direct and indirect poverty reduction through lowering income inequality and how these variables influence poverty by province. This study employed secondary data, including panel data for 2010-2023 from 34 provinces in Indo-nesia, which were analyzed using an autoregressive cross-lagged SEM model. The study finds that economic growth and fiscal policy on spending on education and health are statistically sig-nificant in reducing poverty directly in non-Java but do not affect it through income inequality. Taxes increase income inequality, and the social safety net does not reduce poverty outside Java. Increased spending on education and health should continue, with improvements in targeting so-cial safety nets and tax reforms needed to make the system more progressive and reduce inequality

This article examines the extent to which the current EU climate protection law fulfils the 1.5-degree limit from Article 2 of the Paris Climate Agreement. To this end, a qualitative governance analysis is applied. On this methodological basis, the main instrument for fossil phasing-out – the emissions trading scheme – and the promotion of hydrogen are discussed as examples. The results show that the EU must further intensify its efforts on its territory and cooperate with other countries since the reformed ETS 1 and ETS 2, the SCF and the CBAM are not sufficiently effective to stay within the 1.5-degree limit of the Paris Agreement. This is also the case with regard to hydrogen policies. The primary focus of energy law on the ETS is therefore fundamentally convincing; however, it should be implemented more consistently, for example in terms of the breadth of the approach, closing loopholes and the level of ambition.

Background: This study addresses a longstanding discrepancy between the observed course of the superior epigastric artery in anatomical specimens and its depiction in many German-language anatomy textbooks. While the artery typically runs ventral to the diaphragm, textbooks inaccurately describe it as passing through the sternocostal triangle (Larrey's fissure). Methods: Anatomical dissections were performed on 40 formalin-fixed cadavers at the Medical University of Vienna. The thoracic and abdominal walls were dissected, and the course of the superior epigastric artery was documented. Literature from the time of Dominique Larrey to present was reviewed to trace the origin of the incorrect anatomical description.Discussion: Findings confirm that the superior epigastric artery does not traverse Larrey's space but remains ventral to the pleural and peritoneal cavities. The erroneous description appears to have originated from a 19th-century misinterpretation by Joseph Hyrtl and was perpetuated in German-language textbooks.Conclusion: The study refutes the long-standing but incorrect description of the superior epigastric artery's course in German-language anatomy textbooks. The findings highlight the importance of revising anatomical literature to correct historical inaccuracies.

Increasing concerns on animal welfare in commercial pig industry include aggression between pigs as it affects their health and growth. Early detection of aggressive behaviors is essential for optimizing their living environment. A major challenge for detection is that these behaviors are observed occasionally in normal conditions. Under this circumstance, a limited amount of aggressive behavior data will lead to class imbalance issue, making it difficult to develop an effective classification model for the detection of aggressive behaviors. To overcome this problem, we approach the aggressive behavior detection problem as a case of anomaly detection rather than classification and propose a model based on anomaly detection, which can better handle unbalanced class distribution and effectively detect the infrequent, aggressive episodes of pigs. The model consists of a convolutional neural network (CNN) and a variational long short-term memory (LSTM) autoencoder. Additionally, we adopted a training method similar to weakly supervised anomaly detection and included a few aggressive behavior data in the training set for prior learning. To effectively utilize the aggressive behavior data, we created Reconstruction Loss Inversion, a novel objective function, to train the autoencoder-based model to increase the reconstruction error of aggressive behaviors by inverting the loss function. Our anomaly detection approach significantly outperforms traditional classification-based methods, effectively identifying aggressive behaviors in a natural farming environment. This method offers a robust solution for detecting aggressive animal behaviors and contributes to improving their welfare.

Variable flow emitters are a new type of emitter for underground drip irrigation that are used in locations where soil moisture is difficult to transport to the surface, which leads to crop emer-gence difficulties. The flow channel structure parameters of emitters affect the hydraulic per-formance of the emitter and its anticlogging ability. In this study, the variable flow emitter at the conventional low–flow water supply stage is taken as the research object. A combination of CFD numerical simulation of a two–phase flow of water and sand and clear water testing of test samples is applied to study the influence laws of 10 groups of variable flow emitter structural combinations on the effluent flow rate (q), flow index (x), particle passage rate and flow field inside the flow channel. The results show that the Realizable k–ε turbulence model can be used to simulate the flow field inside the variable flow emitter flow channel. The nRMSE between the measured and simulated values of q is 11.23%, and the relative error between the measured and simulated values of x is 4.66%, which gives a high simulation accuracy. The polar analysis shows that the tooth angle A has the smallest effect on the effluent flow rate q0.1 under 0.1 MPa, x, and particle passage rate of the variable flow emitter. The depth of the flow channel D, the spacing of the teeth B, and the height of the teeth E have a different order of precedence in the influence of the three indices, which are D > B > E > A, B > E > D > A, and E > B > D > A, respectively. The value of particle passage rate is positively correlated with the mean flow velocity (v) and the mean turbulent kinetic energy (k) in the flow channel, and particle passage rate tends to increase and then decrease with the increase of x. The retention time (t) of the particles in the flow channel is closely related to the magnitude of v and k. Three multivariate linear regression equations (R2 = 0.883 ~ 0.995) were constructed for q0.1, x, and particle passage rate versus the flow channel structural parameters. Using the scipy.optimize.minimize function in Python, we de-termined the three optimal combinations of flow channel structural parameters corresponding to better hydraulic performance: q0.1 is 1.5 or 2 L/h (objective function y = min x), better clogging resistance (y = max particle passage rate), and both (y = min (0.5 x - 0.5 particle passage rate)). The research results can provide a ref-erence for the optimal design of variable flow emitters.

A major problem of the technological production process of the metallurgical-grade silicon is formation of a large amount of microsilica. However, this material can be a significant source of raw materials for its own production. Hence, this study is aimed to solve the problem of micro-silica utilization, i.e. the technogenic dust-like waste generated during the melting of the technical-grade silicon. Within this study, the technology of the joint briquetting of microsilica was investigated with the carbonaceous reducing agents, i.e. by obtaining of mono-charge and by melting of the technical-grade silicon from the obtained mono-charge in the 200kVA ore-thermal furnace. Results of the study show that the briquettes in the melting process of the technical-grade silicon can be used in the range from 0 to 50%. The using of briquettes may significantly improve the technological parameters. When briquetted charge is applied only, the technological parameters will deteriorate significantly. The material balance of silicon melting showed the recovery rates of the main elements (Si, Al, Ca and Fe). It recorded a decrease in content of aluminum from 1.9-2.1% to 0.5-0.7%, calcium from 0.2-0.3% to 0.07-0.1% and titanium from 0.2-0.23% to 0.11-0.13% during the transition to briquetted monocharge. Phosphorus content increased from 0.004-0.005 to 0.011-0.013%.

Evans' Syndrome (ES) is a rare autoimmune disorder characterized by the simultaneous occurrence of immune thrombocytopenia (ITP) and autoimmune hemolytic anemia (AIHA). Thrombotic complications in ES patients are uncommon, particularly involving Buerger's Disease (BD). We report a case of a 49-year-old male with ES and a history of diabetes and heavy smoking, presenting with a necrotic wound on his right great toe. Diagnostic evaluations revealed severe stenosis and thrombosis in the lower limb arteries, diagnosed as BD. The patient underwent successful popliteal-tibioperoneal artery bypass surgery and subsequent disarticulation and revision of the distal phalanx, followed by the application of an acellular dermal matrix (ADM) to promote healing. Post-surgery, the patient showed significant improvement in blood flow and complete epithelialization without complications. This case highlights the importance of a multidisciplinary approach in managing complex wounds in ES patients, suggesting potential treatment pathways for future cases involving BD

This paper, from the perspective of Mode 3 of knowledge production, takes the important carrier of knowledge, scientific research papers, as the research object. The mainstream databases (SCIE and SSCI) are chosen as the data sources. Firstly, bibliometric methods are applied to analyze the cooperation status among the main bodies of paper production, including authors and their affiliated institutions, countries, and disciplines; secondly, the Analytic Hierarchy Process (AHP) is used to construct a comprehensive evaluation model for the state of research cooperation in carbon neutrality. Based on the evaluation model, the cooperation characteristics of different disciplinary fields and the relationship between paper cooperation status and high-impact research papers are comparatively analyzed. At the same time, an analysis is conducted on the support from the government, the sponsorship from enterprises, and the participation of the public in the process of paper production. Finally, some suggestions are put forward on how to build an innovative ecosystem for carbon neutrality research from the perspective of Mode 3 of knowledge production.

Background This study aimed to identify the prominent risk factors that may trigger danger signals of early onset of vascular deregulation in T1D. The risk factors we have identified may serve as dual-purpose biomarkers of rapid diagnosis that offer prospective tailor-made resolution therapeutics. Methods The healthy control (HC) was compared with individuals diagnosed with T1D for the risk factors of vascular deregulation in published research studies from year 2013 to 2023. The PubMed, Web of Science and Google Scholar databases were searched from 1/1/2013 to 1/9/2023. The risk of bias was assessed with the Cochrane (ROBINS-I ) tool, which is relevant to clinical subjects. A random effect model for continuous data was followed and analysed by RevMan 5.4 and GraphPad Prism software. Results 80 relevant case-control studies having 5293 HC and 7492 T1D patients were included. The age and sex-matched HC consisted of persons free of disease and not under any medication while clinical subjects of all age groups were included. 28 risk factors were grouped into six primary outcome models, all of which favoured the T1D synonymous with a high risk of CVD. Conclusions Our findings have strong implications for improving the quality of life and health economics related to vascular disease in T1D. HbA1c% is the most effective biomarker, followed by FBG, LDL-C, and AI% which the clinicians could evaluate using a simple blood test or non-invasive techniques. (Protocol registered at https://www.crd.york.ac.uk/prospero/ CRD42022384636).

Vitamin A, or retinol, is one of the most effective anti-ageing molecules, but it presents issues with photo-sensitivity and irritation. Retinol-like alternatives are emerging, but have so far been less effective. Here, we present a Silibum marianum extract (SME) as a retinol-like ingredient providing both safety and efficacy. SME was compared to the reference compound, retinol, and to the main alternative, bakuchiol. In ex vivo tests, skin explants from a 58-year-old donor were treated with pure retinol (0.1%), bakuchiol (0.2%) or SME (0.8%). After 5 days, collagen and hyaluronic acid levels were analysed. A placebo-controlled study involving 57 volunteers (ages 45-73 years) was also conducted, with products applied twice-daily for 56 days. Results were measured by AEVA-HE and VISA. Levels of collagen III were significantly increased by SME, by 23% and 16% compared to bakuchiol and retinol, respectively. Compared to bakuchiol, SME treatment increased hyaluronic acid production by 36%. In clinical tests, SME had a significantly stronger anti-wrinkle effect than bakuchiol – reducing the number of wrinkles on the forehead by 21%, and their circumference by 17% – producing effects similar to retinol, and better than bakuchiol. In the self-assessment, 43% of volunteers reported discomfort while using retinol, as compared to 0% for the SME formulation. By enhancing levels of collagen III – the youth collagen – and hyaluronic acid in the skin, SME paves the way for the maturation of collagen I fibrils and skin plumping. With its stronger efficacy compared to bakuchiol and enhanced safety profile compared to retinol, SME may be the next-generation of natural alternatives to retinoids.

To make wind power more competitive, it is necessary to reduce turbine downtime and reduce costs associated with wind turbine Operation and Maintenance (O&amp;M). Incorporating machine learning in developing condition-based predictive maintenance methodologies for wind turbines can enhance their efficiency and reliability. This paper presents a monitoring method that utilizes Base Density for the Support Vector Machine (BDSVM) and the evolutionary Fourier spectra of vibrations. This method allows smart monitoring of the function evolution of the turbine. A complex optimal function (FO) for 5-degree order has been developed that will be the boundary function of the BDSVM to timely determine the magnitude, frequency, and place of the failure occurring in wind turbine drive.

Aim: To evaluate the panmacular subthreshold micropulse laser treatment results among patients with central serous chorioretinopathy (CSC) and their correlation with functional and morphological parameters. Material and methods: The examined group included 10 non-treated and 41 treated patients with acute, recurrent, and chronic CSC (13 F, 38 M, mean age 44.11±6.5) and 14 healthy controls (6 F, 8 M, mean age 45±9.3). The BCVA examination, ophthalmoscopy, microp-erimetry, angio-OCT and OCT were performed. The medical history regarding chronic general disorders and known risk factors were recorded. Results: Complete resorption of SRF was obtained in 100% aCSC, 86.66% cCSC, and 63.63% r CSC. BCVA and RetSens significantly improved most of the patients treated in aCSC. The lowest BCVA and RetSens, but the largest pachyvessel and disease duration, were found in rCSC. A strong negative correlation between final BCVA and disease duration was found. No patient demonstrated laser lesions following treatment. Conclusions: The panmacular MPLT therapy leads to long-term enhancement of functional and morphological parameters in all CSC patients. The acute CSC patients showed the most significant improvement. The procedure is safe and could be considered a preferred treatment option for all active CSC cases. Timely treatment is crucial for beneficial outcomes.

As companies increasingly undergo digital transformation, the role of talent management pro-cesses becomes pivotal in enhancing overall organizational performance. The research addresses the significance of talent management in corporate digital transformation, examining whether variations in the digitalization of these processes can be attributed to company size. A qualitative approach was employed, utilizing a questionnaire, collecting responses from 202 organizations across diverse sectors. Findings reveal disparities in digitalization throughout the talent man-agement process, with pronounced presence in the attracting, selecting, and rewarding phases, but diminishing in deployment and development, further declining in planning. A positive cor-relation between company size and adoption of specific digital platforms was observed. Larger enterprises exhibit greater utilization of digital platforms in talent deployment and development. Moreover, corporate communication tools are consistently utilized in the rewarding phase, irre-spective of company size. These findings offer practical insights for organizations to optimize their digitalization strategies based on their scale, thereby contributing to more effective and tailored digitalization endeavors. The uniqueness of this research lies in its exploration of the in-fluence of company size on the digitalization of talent management processes and its potential to explain variations across different stages of these processes.

A great deal of studies have assessed the expression of noncoding RNAs (ncRNAs) as well as their relevant molecular functions and biological mechanisms in the individuals of alcohol dependence. Alcohol dependence is one of the most prevalent neuropsychological disorders worldwide, and its pathogenesis is intricate and inadequately understood. There is considerable evidence demonstrating substantial links between multiple genetic factors and the development of alcohol dependence. Critical roles of ncRNAs have been emphasized in the pathophysiology of mental diseases including alcohol dependence. In the comprehension of ncRNAs action and their mechanisms of modification, they have emerged as therapeutic targets for a variety of psychiatric illness including alcohol dependence. Worth mentioning, dysregulated expression of ncRNAs has been regularly detected in individuals of alcohol dependence. An in-depth knowledge of roles of ncRNAs and m6A modification may be valuable for the development of a novel treatment against alcohol dependence. In general, a deeper comprehension of functional roles ncRNAs may make significant contributions to the precise diagnosis and/or actual treatment of alcohol dependence. Here in this review, we mostly focused on the up-to-date knowledge regarding alterations and/or modifications in the expression of ncRNAs in alcohol dependence, and then, presented their prospects for future research and therapeutic application with a novel concept of engram-system.

To address the insufficient mechanical properties of calcined phosphogypsum, this research aims to investigate the utilization of basalt fiber and calcium carbonate whiskers as reinforcing agents. The study examines their impact on the flexural and compressive strength, toughness, water resistance, and tensile strength of calcined phosphogypsum. In the individual tests, basalt fibers with different lengths (3 mm, 6 mm, 9 mm, and 18 mm) were added at dosages of 0%, 0.5%, 1.0%, and 1.5% respectively. The findings demonstrate that basalt fiber effectively enhances the flexural and compressive strength, toughness, and tensile strength of calcined phosphogypsum, albeit potentially compromising water resistance. Among the various fiber lengths, the 6 mm fibers exhibit the most advantageous influence on the performance of calcined phosphogypsum. A subsequent test was conducted to investigate the impact of cross-scale fibers on the properties of calcined phosphogypsum by mixing 6 mm basalt fibers and calcium carbonate whiskers. The results illustrate that calcium carbonate whisker refines the pores, thereby improving the flexural strength and toughness of calcined phosphogypsum. Furthermore, it compensates for the water resistance limitations associated with the sole utilization of basalt fiber while further augmenting the tensile strength and strain capacity. However, it should be noted that increasing the dosage of both calcium carbonate whiskers and basalt fibers concurrently leads to increased porosity of phosphogypsum and reduced compressive strength.

In the conservation of monumental heritage, the collection and utilization of information are of primary importance. The Heritage Building Information Modeling (HBIM) procedure harnesses the potential of three-dimensional models, offering significant advantages in accessing documentation, interoperability, multidimensionality of intervention design, cost evaluation and maintenance management. Attention here is focused on the Certosa di Pisa, a large historical complex built in the 14th century as a monastery of the Carthusian order, currently in a state of deterioration and in need of restoration and re-functionalization. The multifaceted nature of this monumental complex, with its intricate interplay of architectural elements spanning different historical periods and featuring diverse techniques, poses a significant challenge for structural safety assessment. This case study presents an opportunity to explore an HBIM approach to streamline the diagnostic process and facilitate the intervention design phase. The goal is achieved by utilizing an accurate 3D model enriched with data from multiple sources and automating certain operations for structural assessment. The usefulness of the HBIM methodology is highlighted as a valuable tool in the realm of Cultural Heritage structures for both technicians and scholars alike.

This paper illustrates an experimental activity for the closed-loop position control of an actuator made using shape memory alloy (SMA) wire. A solution with the self-sensing effect was implemented to miniaturize the systems, i.e., without external sensors. A proportional control algorithm was initially used, demonstrating the idea's feasibility: the wire can behave simultaneously as an actuator and sensor. An experimental investigation was subsequently conducted for the optimization of the developed actuator. As for the material, a Flexinol wire, Ni-Ti alloy, with a diameter of 0.150 mm and a length of 200 mm, was used. Preliminarily, a characterization of the SMA wire at constant and variable loads was carried out: the characteristics detected are elongation vs. electric current and elongation vs. electrical resistance. The control system is PC-based with a data acquisition card (DAQ). A drive board has been designed and built to read the wire's electrical resistance and power it by pulse width modulation (PWM). A notable result is that the actuator works with good precision and in dynamic conditions, even when it is called to support a load up to 65% different from that for which the electrical resistance-length correlation has previously been experimentally obtained, on which the control is based. This opens up the possibility of using the actuator in a counteracting configuration with a spring, which makes hardware implementation and control management simple.

In Belgium, sex work was recently decriminalized to enhance street-based sex workers’ (SSWs) health. This qualitative study explores stakeholders' perceptions of the impact of the working environment on street-based sex workers’ occupational safety, health and well-being in Brussels. In-depth interviews with seven stakeholders directly involved with SSWs were conducted with data analyzed using qualitative content analysis. The analysis of study data resulted in one theme: “A power imbalance and a lack of concerted efforts among stakeholders are detrimental to the occupational safety, health, and well-being of street-based sex workers”. In Brussels, the majority of SSWs face various challenges due to structural vulnerabilities, thus limiting their choices regarding their work environment, and further compromising their health. Limited access to resources and severe constraints within their working environment contribute to a lack of safety and adverse health outcomes. A stigma mechanism fueled by ideology and personal interests prevent the enforcement of their rights regarding their working environment, safety and health promotion. The lack of involvement of key stakeholders, especially from the public sector, prevents the majority of SSWs in Brussels from benefiting from a sound working environment and the promotion of their health, safety and well-being.

COPD is a "heterogeneous lung condition characterized by chronic respiratory symptoms. It is a leading cause of death and illness and is associated with a substantial economic burden worldwide. Furthermore, it is marked by frequent exacerbations, which significantly contribute to morbidity and mortality, as well as the overall burden. These exacerbations are frequently triggered by bacterial infections.So far, the most commonly implicated Bacteria are Pseudomonas aeruginosa, Klebsiella pneumoniae, Haemophilus influenzae, Moraxella catarrhalis, and Streptococcus pneumoniae.The advent of culture-independent techniques, such as next-generation sequencing techniques (NGS), allows us to characterise the lung microbiome in different disease states.

The role of coalesced bainite in hydrogen embrittlement of tempered martensitic steels was investigated. Results showed that the coalesced bainite significantly enhanced the hydrogen embrittlement resistance by restricting hydrogen accumulation at the prior austenite grain boundaries, thus shifting the hydrogen-assisted failure mode from intergranular to transgranular fracture.

Background: Existing human cell immortalization methods made the cells obtain oncogenesis phenotype and/or caused the cells gain and/or lose chromosomes. Immortalized normal human T cells lines provide critical in vitro models for basic research and therapeutic products development.Methods: We utilized a CRISPR/Cas9 system to replace a single copy of the exon 2 of the cell cycle inhibitor gene CDKN2A (encoding p16 and p14 proteins) with a single copy of human telomerase reverse transcriptase (hTERT) to immortalize human primary CD8⁺ T cells (hCD8⁺T-TERT). By using Cas9 protein and low donor DNA copies/cell, we successfully immortalized hCD8⁺T cells with a single copy of hTERT transgene, which also avoided uncontrolled insertion of Cas9 gene and guide RNA vector.Results: Human primary CD8+ cells were immortalized and expanded more than 2.6 × 10⁷ times. Characterization of the cells revealed that the immortalized CD8⁺ T-TERT cells retained most of the cell surface markers and normal karyotype. The CD8⁺ T-TERT cells also retained the dependence of IL-2 and CD3/CD28 activator for survival and expansion.Conclusion: we established a stable immortalized CD8⁺ T cell line that had a phenotype consistent with T cells and will be a useful research model.

Field of Research This research study investigates the role of distributed leadership and culture within small enterprises in Malta, an area in which there has been very limited research. It focuses on the interaction between these two elements and their impact on organizational behaviour and effectiveness. Several studies (Jardon et al 2019; Cope et al., 2011; de Oliveira et al., 2015; Mohanty et al., 2012;) suggest that effective leadership and culture are vital elements in the successful endeavours of small organizations. Schein (2006) further asserts that they are two different faces on the same coin and the dyadic interaction characterizes “how leaders create culture and how culture defines and creates leaders”. Distributed Leadership is a systematic practice of interactions and synergies between leaders, followers, and the situation (Spillane 2013). It is different from traditional leadership, which involves top-down management because it tends to be more democratic and participatory, whereby influence and decision-making are shared among multiple individuals rather than being controlled by a single leader. (Xhemajli et al. 2022) Methodology Adopting a naturalistic approach and guided by an interpretivist, constructivist epistemological stance, this research delves into the intricate interplay between leadership and culture within small businesses. The chosen research methodology employs Grounded Theory, recognized for its robust and systematic process facilitating the observation of patterns through intensive iterative and highly analytical procedures (Charmaz, 2015).In the initial stages of field research, characterized by 'responsive interviewing' (Rubin and Rubin, 2012), data sampling commenced with convenience sampling. This initial phase gradually evolved into a refined strategy incorporating selective sampling and theoretical sampling (Corbin and Strauss, 2015). The shift in sampling approaches reflects a deliberate focus on collecting data based on its specific contribution to the development and comprehension of the dimensions, properties, and characteristics of key concepts.The induction of theory is a product of successive comparative analyses, involving the systematic comparison of data points to identify both similarities and variations. Abductive reasoning is integral throughout the analytical process, with particular emphasis during constant comparative analysis of categories, leading to theoretical integration (Charmaz, 2006). This meticulous approach aligns with the assertion of Strauss and Corbin (2015) that grounding theory in data enhances the likelihood of deriving theories that authentically reflect reality.The key advantage of using this approach is that the analysis carried out goes beyond deep exploration and rich description and actually develops a framework that explains the phenomena observed (Parker and Roffey, 1997, p.218). This is very important if the findings are to contribute to the knowledge enhancement of any field of practiceThe culmination of this research effort is the presentation of a set of interconnected concepts, intricately woven together into an emergent parsimonious model (Corbin and Strauss, 2015). This model serves to explain the dynamic interplay between leadership and culture, elucidating its tangible impact on the effectiveness of small enterprises. Research Contribution:Implications for Practice This research contributes to the literature on leadership and organizational culture in small enterprises, particularly in the context of Malta where such studies are scarce. By providing an initial exploration of these phenomena and their impact on organizational behavior, this paper lays the groundwork for further inquiry into this important area. Furthermore, the study offers practical insights for leaders of small enterprises by elucidating leadership behaviors observed in established organizations. Through applied cases, it demonstrates how the abstract concept of culture can be translated into a practical instrument that supports leadership and organizational development. This not only enriches the understanding of leadership dynamics but also provides tangible strategies for implementation. Moreover, the research contributes empirical evidence on the development of leadership functions within small enterprises, emphasizing the potential of shared and distributed leadership models. By grounding its findings in data, the study equips leaders with a deeper understanding of how these leadership approaches can shape organizational development, fostering more effective management practices in small businesses. Methodologically, the adoption of Grounded Theory methodology showcases its efficacy in exploring complex management phenomena. By employing this approach, the researchers were able to gather rich descriptions and develop an explanatory framework, highlighting its applicability in studying nuanced organizational dynamics. Implications for Policy and Theory This research also holds significant implications for policymakers, academic researchers and institutions involved in supporting small businesses. By providing insights into distributed leadership and cultural influences on organizational effectiveness, it offers a basis for informed policy formulation and support mechanisms. The conceptual model emerging from this study serves as a foundation for designing more targeted policies that cater to the unique needs of small enterprises. By understanding the intricacies of leadership dynamics and cultural contexts, policymakers can develop interventions that foster a conducive environment for small business growth and sustainability. Additionally, academic researchers can use these findings to further refine theoretical frameworks and empirical studies in the field, contributing to ongoing scholarly dialogue and knowledge advancement.

This work focuses on the theoretical study of the effect of entanglement in the Yttrium Barium Copper Oxide (YBCO) superconductor on the critical current density, critical magnetic field, and penetration depth. Using the Ginzburg Landau (GL) theory, the expression for the GL coherence length, the critical current density, the lower critical magnetic field (Hc1), and the upper critical magnetic field (Hc2) for the entangled superconducting YBCO was obtained. At zero external magnetic fields, YBCO was found to undergo a transition from the normal state to the superconducting state at 93K and returned to normal. We found a direct relationship between the GL coherence length penetration depth and the temperature of the entangled superconducting YBCO. The graphs of the lower critical magnetic field (Hc1) and critical current density against temperature show a non-linear dependence.In contrast, the graph of the upper critical magnetic field (Hc2) against temperature (T) shows the linear dependence, which is in agreement with existing theoretical observations. On the other hand, the graph of critical current density against the distance of separation between the entangled electrons that form a cooper pair showed that the critical current density increases between 1.8 and 6 nanometers attaining a constant value after reaching 7 nanometers for infinite distances. Finally, for lower critical fields, the magnetic field decreases between 1.5 to 6 nanometers attaining a constant value of the magnetic field, for infinite values of distance of separation between the entangled pair of electrons.

Ever since Varela and Maturana proposed the concept of autopoiesis as the minimal requirement for life, there has been a focus on cellular systems that erect topological boundaries to separate themselves from their surrounding environment. Here we reconsider whether the existence of such a spatial boundary is strictly necessary for self-producing entities. This work presents a novel computational model of a minimal autopoietic system inspired by dendrites and molecular dynamics simulations in three-dimensional space. A series of simulation experiments where the metabolic pathways of a particular autocatalytic set are successively inhibited until autocatalytic entities that could be considered autopoietic are produced. These entities maintain their distinctness in an environment containing multiple identical instances of the entities without the existence of a topological boundary. This gives rise to the concept of a metabolic boundary which manifests as emergent self-selection criteria for the processes of self-production without any need for unique identifiers. However, the adoption of such a boundary comes at a cost, as these autopoietic entities are less suited to their simulated environment than their autocatalytic counterparts. Finally, this work showcases a generalized metabolism-centered approach to the study of autopoiesis that can be applied to both physical and abstract systems alike.

Silicon carbide single crystal (SiC) has been widely used in the field of power devices, while it is difficult to fabricate ultra-flat surface by traditional manufacturing technologies due to its difficult-to-machine property. This paper investigates the interaction process during femtosecond laser ablation of crystalline silicon carbide based on the two-temperature model simulation and experimental study. The findings reveal that parameters such as laser pulse energy, scanning interval, and defocus amount exert significant influence on ablation depth, roughness, and surface morphology. The femtosecond laser proves effective in removing surface defects from cut SiC substrates, albeit resulting in increased surface roughness. However, subsequent polishing treatment of the laser-ablated silicon carbide surface can mitigate this roughness, underscoring the feasibility of laser surface ablation for silicon carbide single crystals.

Phyllanthus emblica (P. emblica) has been described in many studies to have multiple therapeutic activities and is considered an important part of Ayurvedic and Unani medicinal systems. This study successfully synthesized P. emblica loaded polyvinylalcohol/gelatin based cryogels (PVA/Gel/P.emblica) to examine their potential in wound dressing applications. Swelling tests, Brunauer-Emmett-Teller (BET) and morphology analysis were conducted within the scope of characterization studies. In vitro cell culture studies were performed using HaCaT cells to illustrate the suitability of the synthesized cryogels as wound dressing material. The swelling tests and BET analysis results showed that swelling and surface area properties of cryogels increased with increasing P. emblica amounts. Morphological results displayed that the cryogels had a dense, interconnected pore morphology and a macroporous structure. 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide (MTT), trypan blue exclusion and live-dead assay results revealed that adding of P. emblica into cryogels led to enhanced cell proliferation, increased cell number, and improved cell viability. Based on the phase contrast microscope, scanning electron microscope (SEM), immunofluorescence and giemsa staining images, it was observed that P. emblica promoted cell attachment, proliferation and penetration. In conclusion, it has been shown that PVA/Gel/P.emblica cryogels are suitable for use as wound dressing materials and can be developed with further studies.

To improve carbon efficiency for urban logistics service system composed of a third-party logistics service provider (3PLs) and an e-business enterprise, low-carbon operation game between them was studied. Considering low carbon technology investment cost and sales expansion effect of low carbon level, profit functions for both players were constituted. Based on their different bargaining capabilities, totally 5 types of game scenarios were designed. Through analytical solution, Nash Equilibria under varied scenarios were obtained. By analyzing these equilibria, 4 major propositions were given, in which, some key variables and system performance index were compared. Results show that the best system yields could only be achieved under the fully cooperative situation; limited cooperation only for carbon emission reduction would not benefit the system performance improvement; E-business enterprise-leading game’s performance overtook 3PLs-leading ones.

To evaluate the effectiveness of a dual approach involving time-restricted eating (TRE) at different times-of-day combined with physical activity (PA) on functional capacity and metabolic health in overweight or obese women. Random allocation of sixty-one participants into four groups: early time-restricted eating plus physical activity (ETRE-PA, n=15, 31.8±10.56 years, 89.68±10.56 kg, 33.5±5.53 kg/m²), late time-restricted eating with physical activity (LTRE-PA, n=15, 30.60±7.94 years, 94.45±15.36 kg, 34.37±7.09 kg/m²), late time-restricted eating only (LTRE, n=15, 27.93±9.79 years, 88.32±10.36 kg, 32.71±5.15 kg/m²) and a control group (CG, n=15, 36.25±11.52 years, 89.01±11.68 kg, 33.66±6.18 kg/m²). The intervention lasted 12 weeks for all groups. Both ETRE-PA and LTRE-PA groups engaged in a rigorous combined aerobic and resistance-training program. Significant reductions in body weight and body mass index were observed in ETRE-PA and LTRE-PA compared to CG and LTRE groups in post-intervention (p&lt;0.0005). Only ETRE-PA group exhibited a significant decrease in fat mass (p=0.02), low-density lipoprotein cholesterol (p=0.01) and aspartate aminotransferase (p=0.002). Significant reductions in alanine aminotransferase levels were observed in ETRE-PA (p=0.004) and LTRE-PA (p=0.02) groups. These two latter groups achieved higher performances in the 6-min walking test, bench press, 30-second squat, crunch test, vertical jump (p&lt;0.0005 for both) and leg extension (p&lt;0.02 for both) when compared to LTRE and CG groups. In conclusion, the integration of TRE with PA leads to greater improvements in body composition, lipid profile, and physical performance with no significant differences between ETRE-PA and LTRE-PA approaches. This combined strategy offers a promising solution in overweight or obese women.

Cellulose nanocrystals are of major research interest because of their use in biodegradable bioplastcs and food packaging, biomaterials, medical and pharmaceutical applications, cosmetics, electronics, and construction materials. This study introduces an approach combining microwave-assisted extraction (MAE) of cellulose from Aloe Vera plant residue and subsequent isolation of cellulose nanocrystals (CNCs) utilizing sulfuric acid hydrolysis. The MAE process, characterized by its rapid heating and penetrating ability, was optimized to maximize cellulose yield from raw biomass sources under various conditions (microwave power, solvent ratio, and time). Following extraction, the purified cellulose was subjected to sulfuric acid hydrolysis under controlled conditions to yield CNCs, with the aim of preserving the intrinsic crystalline structure while enhancing the material's physicochemical properties. The search for biocompatible and biodegradable materials suitable for biomedical applications has led to significant interest in hydrogels composed of natural polymers. Among these, hydrogels synthesized from cellulose and polyvinyl alcohol (PVA) have emerged as promising candidates due to their unique physical properties and compatibility with biological tissues. This study presents the formulation, characterization, and potential biomedical applications of a cellulose/PVA hydrogel. The hydrogel was synthesized to enable the formation of a semi-crystalline network that imparts the material with enhanced mechanical properties.

Coconut water, the clear liquid extracted from coconuts (Cocos nucifera L.), is a refreshing tropical drink with a booming market. However, despite its success, its moisturising properties remain controversial. The aim of this research is to inform consumers about the hydrating power of coconut water sold on the streets of Abidjan. To achieve this objective, a survey of coconut water consumption was carried out followed by in-vitro experiments using biochemical, physicochemical and functional analyses. The survey revealed that coconut water was well known to consumers (100%) for its fortifying (33.33%), digestive (29.33%) and refreshing (28.34%) properties. Coconut water contained carbohydrates (4.5±0.0%), dry matter (5.2±0.0070%), energy (19.92±0.0%) and ash (0.44±0.0%). Coconut water also contained minerals, notably sodium (220.45±0.4949 mg), potassium (1591.02±6.10 mg) and phosphorus (276.1±10.18 mg). In other hand, the volume of urine after consumption of coconut water was lower than that after consumption of mineral water, with values falling from 138.5 mL (T1) to 66.67 mL (T4) and then from 41.67 mL (T1) to 36.33 mL (T4) for coconut water. Coconut water is diuretic and therefore cleanses the bladder. Coconut water seems to have greater hydrating power than mineral water.

During the last few years, the world witnessed one of the worst calamities affecting humankind- the COVID-19 pandemic. We also witnessed the development of vaccines at an unprecedented pace against the SARS-CoV-2, the causative agent. India, which was one of the countries most impacted by COVID-19, developed its indigenous vaccine in addition to utilizing the ones developed by other countries. Initially, the antibody level and the neutralizing antibody titer against the pathogen were considered as the correlates of immune protection from the disease. The long-term protection from the pathogen is provided by the immune memory cells viz. T and B memory cells and their ability of efficient recall responses. In this regard, global research focused mainly on the mRNA-based vaccines. The studies on immune memory response, particularly- the B cell memory response bestowed by the vaccines given to Indians is relatively obscure. In this work, we examined the level of RBD specific memory B cells in the peripheral circulation of the study participants and the ability of B cells to secrete antigen-specific antibodies among Indians vaccinated with Covaxin (BBV152), Covishield (AZD1222), Corbevax (BECOV2D) and Sputnik Light as well as unvaccinated individuals. Our study revealed that Corbevax and Sputnik Light conferred better antibody-secreting cell (ASC) responses.

Oncolytic measles virus (MeV) is a promising anti-cancer treatment. However, the production of high titers of infectious MeV (typically 10⁷–10⁹ TCID₅₀ per dose) is challenging because the virus is unstable under typical production conditions. The objective of this study was to investigate how the multiplicity of infection (MOI) and different media – serum-containing (SCM), serum-free (SFM) and chemically-defined (CDM) – affect MeV production. We infected Vero cells at MOIs of 0.02, 0.2 or 2 TCID₅₀ mL^-1 and the lowest MOI resulted in the largest number of infected cells towards the end of the production period. However, this did not equate to higher maximum MeV titers, which were similar for all MOIs. The medium had a moderate effect, generating maximum titers of 0.89–2.17 × 10⁶, 1.08–1.25 × 10⁶ and 4.58–9.90 × 10⁵ TCID₅₀ mL^‑1 for SCM, SFM and CDM, respectively. Infection at a low MOI often required longer process times to reach maximum yields. Our findings show that SCM, SFM and CDM are equally suitable for MeV production in terms of yield and process time. This will allow MeV production in serum-free conditions, addressing the safety risks and ethical concerns associated with the use of serum.

Source water quality is a key determinant of drinking water quality. The recast European Union 2020/2184 drinking water directive (DWD) introduced the obligation for comprehensive risk assessment in drinking water supplies, including the water source and incorporated new elements of natural origin in the list of parameters to be monitored. The current study is the first comprehensive assessment of 15 natural elements (B, Ba, Be, Ca, Co, K, Li, Mg, Mo, Na, Se, Sr, Ti, U and V) in 1155 (82%) Hungarian drinking water sources, including surface water, bank filtered and groundwater sources. Parameters posing a risk to health (Se, V and U) were typically below the lower limit of quantification (LOQ), but higher concentrations (max. 7.0, 17 and 41 µg/L, respectively) may occur in confined locations, the latter exceeding the DWD parametric value in one water supply. Li in a small geographical area, Mg and Ca in the majority of the water supplies reached the concentration range assumed to be protective to health. Water sources were grouped in 6 clusters based on their element distribution, some of them also showing clear geographical patterns. Water types were not differentiated, with the exception of karstic waters (dominated by Ca and Mg). None of the investigated parameters are expected to be a source of public health concern.

The intranasal route of drug administration is characterized by high bioavailability and is considered promising for rapid delivery of drugs with systemic action to the central nervous system, bypassing the blood-brain barrier. This is particularly important for the use of neuroprotective drugs in the treatment of brain tissue damage in infants caused by the effects of intrauterine hypoxia. Creation of new dosage forms for neonatology with the use of software and mathematical technologies in pharmaceutical development allows to create cerebroprotective drugs with controlled pharmaco-technological properties, thus reducing time and resources for necessary research. We developed a formulation of a new nasal gel formulation with Angiolin using Box-Benken experiment design for the therapy of prenatal CNS damage. It was found that the consistency properties of the nasal gel were significantly influenced by the gelling agent and mucoadhesive component - sodium salt of carboxymethylcellulose. We have optimized the composition of nasal gel formulation with Angiolin using the formed models and relationships between the factors. The optimized composition of the obtained nasal gel has satisfactory parameters of thixotropic properties. The developed 1% gel for neuroprotection with Angiolin meets all the requirements for harmlessness and safety to drug forms of this group - low toxicity, absence of local irritant and allergic effect.

In this paper, based on our previous expertise on ceramic artifacts, several archaeometric methods applied to some samples collected from the Dudești archaeological site (Oltenia region, Romania) are reported for the first time in the literature. The chemical composition and microstructural and morphological characterization of these samples offer important conclusions about the processing conditions. Some specific techniques such as X-ray diffraction (XRD), wave-length-dispersive X-ray fluorescence (WDXRF), Optical microscopy (OM), stereomicroscopy, scanning electron microscopy (SEM), Fourier transform infrared (FTIR) spectroscopy and Raman spectroscopy, provide composition information about pigments and their decay processes. Additionally, the Brunauer-Emmett-Teller (BET) method helps to estimate pore sizes and specific surface areas. Thermal analysis (TGA) was used to establish details regarding the production technology and the raw materials source used to make the ceramics, too. The obtained results indicated that the ceramics are based on a paste of muscovite, feldspar, with high plasticity, quartz, melanterite, and calcite, the latter in very low concentrations. According to the obtained results, we could assume that non-calcareous clays are present in the investigated samples because calcium exists in low concentrations. Gypsum is present, too, in very low concentration, identified by the presence of sulfate group in WDXRF. In the same context, iron oxides significantly impact the firing atmosphere of iron-rich clay, resulting in blackening under reducing conditions and reddish coloration under oxidative conditions. Using hematite and gypsum as pigments further contributes to the color variations in the pottery. The consistent firing temperature range of 200-600 °C in Dudești pottery implies a standardized production process, the variation in color being dependent on the specific reducing/oxidative regime conditions. This relationship between clay composition and local sources suggests a connection to Neolithic pottery production in the region and their color depending on the reducing/oxidative regime conditions.

Background/Aim: Stool gluten immunogenic peptides (GIP) determination is now considered a valuable tool for detecting dietary lapses in treated celiac disease (CeD) patients. Our study aims to explore the diagnostic performance of a qualitative lateral flow immunoassay point-of-care test (LFIA/PoCT) compared with a qualitative enzyme-linked immunosorbent assay (ELISA) for detection of stool GIP. Methods: The study is a post hoc analysis of stool samples collected in the real-life conditions from a cohort of gluten-free diet-treated CeD patients. Stool GIP was measured in µg/g of stool using an ELISA kit (iVYLISA GIP S®, Biomedal SL). For the qualitative evaluation of stool GIP, a LFIA/PoCT test (GlutenDetect®; Biomedal S.L) was employed, which reported results as positive or negative. The LFIA/PoCT performance was evaluated against ELISA, considered as the gold standard. GIP concentrations

Autosomal dominant polycystic kidney disease (ADPKD) is an inherited disorder characterized by renal tubular cystic dilatations. The cysts can develop anywhere along the nephron and over time the cystic dilatation lead to kidney enlargement. On the other hand, the cysts begin to reduce the number of functional nephrons as a consequence of cystic expansion that further contributes to the decline in renal function over the years. The pressure exerted by the dilated cysts lead to compensatory mechanisms that further contribute to the decline in renal function. These structural changes are responsible of glomerular hyperfiltration states, albuminuria, proteinuria, and haematuria. However, the presentation of ADPKD varies in children from a completely asymptomatic child with incidental ultrasound detection of cysts to a rapidly progressive disease. There have been reports of early onset of ADPKD in children younger than 2 years that showed a more rapid decline in renal function. ADPKD is caused by mutation in PKD1 and PKD2 genes. Today, the PKD1 gene mutation seems to account for up to 85% of the cases worldwide, and it is associated with worse renal outcomes. Individuals with PKD2 gene mutation seem to present a milder form of the disease, with a more delayed onset of end stage kidney disease. The cardinal sign of ADPKD is the presence of renal cysts during renal ultrasound. The current guidelines provide the clinicians the recommendations for genetic testing in children with a positive family history. Given that the vast majority of children with ADPKD present with normal or supra normal kidney function we explored the glomerular filtration rates dynamics and the renal ultrasound adjusted percentiles. 14 out of 16 patients had kidney percentile over 90%. The gene mutations were equally distributed among our cohort. In addition, we compared the modified Schwartz formula to the quadratic equation after adjusting the serum creatinine measurements. It seems that even though children with ADPKD have enlarged kidneys, the renal function is more likely normal or near normal when the quadratic estimation of glomerular filtration rate is used (qGFR tended to be lower, 111.95 ± 12.43 ml/min/1.73m2 compared to Schwartz eGFR 126.28 ± 33.07ml/min/1.73m2, p=0.14). Also, when the quadratic equation was employed, not even a patient reached the glomerular hyperfiltration thresholds. The quadratic formula showed that glomerular filtration rates are linear or slightly decreasing after 1-year of follow-up (Quadratic ΔeGFR=0.32±5.78ml/min/1.73m2) as opposed to Schwartz formula that can falsely classify children in a hyperfiltration state ΔeGFR=7.51±19.46ml/min/1.73m2), p=0.019.

A large diversity of epigenetic factors, such as microRNAs and histones modifications, are known to be capable of regulating gene expression without altering DNA sequence itself. In particular, miR-1 is considered the first essential microRNA in cardiac development. In this study, miR-1 potential role in early cardiac chamber differentiation is analyzed through specific signaling pathways. For this, we performed in chick embryos functional experiments by means of miR-1 microinjections into the posterior cardiac precursors -of both primitive endocardial tubes- committed to sinoatrial region fates. Subsequently, embryos were subjected to whole mount in situ hybridization, immunohistochemistry and RT-qPCR analysis. As a relevant nov-elty, our results revealed that miR-1 increases Tbx5, Gata4 and AMHC1, while this microRNA diminishes Mef2c expression, during early differentiation of cardiac sinoatrial region. Further-more, we observed in this developmental context that miR-1 upregulates CRABPII and RARß, and downregulates CRABPI, which are three crucial factors in retinoic acid signaling pathway. Interestingly, we also noticed that miR-1 directly interacts with HDAC4 and Calmodulin, as well as with Erk2/MAPK1, which are three key factors actively involved in Mef2c regulation. Our study shows, for the first time, a key role of miR-1 as an epigenetic regulator in early differenti-ation of cardiac sinoatrial region through orchestrating opposite actions between retinoic acid and Mef2c, fundamental to properly assign cardiac cells to their respective heart chambers. A better understanding of those molecular mechanisms modulated by miR-1 will definitely help in fields applied to therapy and cardiac regeneration and repair.

Coxsackievirus A6 (CV-A6) has emerged as the predominant causative agent of hand, foot, and mouth disease (HFMD) in young children. Since the declaration of coronavirus disease 2019 (COVID-19) as a global pandemic, the incidence of infectious diseases, including HFMD, has decreased markedly. When social mitigation was relaxed during the COVID-19 pandemic in 2022, re-emergence of HFMD was observed in Gwangju, South Korea, and seasonal characteristics of the disease appeared to have changed. To investigate the molecular characteristics of enterovirus (EV) associated with HFMD during 2022, 277 specimens were collected. Children aged under 5 years accounted for the majority of affected individuals. EV detection and genotyping were performed using real-time RT-PCR and nested RT-PCR followed by sequence analysis. EV detection rate was found to be 82.3%, and the main genotype identified was CV-A6. Sixteen CV-A6 samples were selected for whole genome sequencing. According to phylogenetic analysis, all CV-A6 strains from this study belonged to the sub-genotype D3 clade based on VP1 sequences. Analysis of 3D polymerase phylogeny showed that only the recombinant RF-A group was identified. In conclusion, circulating EV types should be continuously monitored to understand pathogen emergence and evolution during the post-pandemic era.

Hybrid reinforcement in a composite material (CM), in many situations, allows better govern material mechanical properties. Polymer matrix CM plate is reinforced with small particles and macro-fibers. Particles are oil shale ash (OSA) powder, macro-fibers – basalt fiber threads im-pregnated by matrix material. With the goal to find out elastic properties of the matrix- polymer with OSA, samples with its different concentrations were experimentally fabricated and their elastic properties were experimentally measured. Obtained data were used in numerical model-ling. Was observed polymer matrix composite slab, reinforced with OSA and three-dimensional (3D) basalt fiber fabric. Fabric are forming threads impregnated by matrix (polymer resin mixed with OSA particles). Damage accumulation in the stretched slab was modelled. Impregnated thread, in the modelling, is observed as a macro-fiber (MF) with averaged elastic properties. With the load increase MF in the material began to break. At first, appeared isolated single breaks. A probabilistic sequential MF rupture accumulation model was accepted and numerical-ly realized. The geometry of the reinforcing knitted fabric was modeled using the Leaf and Glaskin approach. In the knitted fabric highly, stressed MF cross-sections are observed as po-tential location where thread breakage can occur. If one thread breaks, the cross-sections of the adjacent threads experience the overload caused by this rupture. More overloaded crossection in the adjacent overloaded thread breaks and we obtain two adjacent broken MF designated as a defect with the size j=2. The probabilities of obtaining defect consisting of at least 2, 3, … j adjacent broken MF in the plate were calculated. The calculations continued until the rupture process becomes unstable (j→∞). The overstresses on adjacent threads in the CM were calculat-ed using the FEM three-dimensional numerical approach. Analytical and stochastic methods were used for the load-carrying capacity determination and different size defects accumulation in the hybrid composite material (HCM) plate. Also, was calculated the probability of the plate rupture.

Introduction: maxillary hypoplasia and mandibular asymmetry may be corrected with orthognathic surgery at the completion of growth. Many patients require segmental Le Fort I osteotomies to obtain the most stable results. Unfortunately, if Invisalign is chosen for pre-surgical preparation, ClinCheck © software does not allow for prediction when these complex surgeries are planned. The objective of this paper was to show the potential of aligners beyond its software in most complex cases like multiple-piece maxillary osteotomies in cleft and non-cleft patients. Method: Thirteen patients who underwent pre-surgical treatment with clear aligners-Invisalign (study group) were matched in terms of diagnosis, surgical procedure, and orthodontic complexity with thirteen patients treated using fixed appliances (control group). A technique based on simple superimposition was devised to enhance the software for creating a suitable occlusion for segmental pre-surgical treatments. Virtual curves following the lower arch were employed to guide the correct pre-surgical positions of the upper teeth. The amount of impressions required in both groups to achieve satisfactory pre-surgical alignment of the segmented arches was compared. Results: one or no refinement phase were needed in the Invisalign group to reach an acceptable pre-surgical occlusion while the amount of pre-surgical impressions taken in order to reach adequate coordination with fixed appliance treatment was slightly higher. The average overall treatment duration did not show a statistically significant variation between the groups. Conclusions: it appears that clear aligner could serve as an effective treatment for individuals with skeletal discrepancies, including cleft and craniofacial anomalies, necessitating segmental Le Fort I osteotomies when aided by the suggested superimposition approach during digital pre-surgical movement simulations. More sophisticated softwares will certainly be implemented in the future.

Background:Caregiving for individuals with neurological disease involves providing physical, emotional, and social support, which can be a challenging and stressful experience. This study aims to compare the caregivers' burden, including the impact on mental and physical health, social support, and quality of life, in different neurodegenerative disorders. Methods:Fifty-five primary caregivers (F=41;mean age=53.07±12.29) of patients with Parkinson's Disease (PD=26), Multiple System Atrophy (MSA=16), and Amyotrophic Lateral Sclerosis (ALS=13), took part in the study. Standardized screening scales for the quality of life (EQ-5D/EQ-VAS and PQoL), levels of the caregiving burden (CBI and FSQ), and the assessment of the anxiety-depressive axis (HADS) were administered. Results: The mean CBI score was higher for caregivers of MSA patients (28.81±21.90) and ALS (25.15±16.23) than for caregivers of PD patients (16.08±10.34; p=0.036). Critical burden (cut-off>36) was present in the caregivers of MSA (31.3%), ALS (23.1%), and PD (19.2%) patients. Caregivers of patients with ALS had a worse perception of quality of life (EQ-5D total score) than caregivers of patients with MSA and PD (p

Two new dimacrolide sesquiterpene pyridine alkaloids (DMSPAs), dimacroregelines A (1) and B (2), were isolated from the stems of Tripterygium regelii. The structures of both compounds were characterized by extensive 1D and 2D NMR spectroscopic analyses, as well as HRESIMS data. Compounds 1 and 2 are two rare DMSPAs possessing unique 2-(3′-carboxybutyl)-3-furanoic acid units forming the second macrocyclic ring, representing the first example of DMSPAs bearing an extra furan ring in their second macrocyclic ring system. Compound 2 showed inhibitory effects on the proliferation of human rheumatoid arthritis synovial fibroblast cell (MH7A) at a concentration of 20 μM.

Obesity is a risk factor for the development of gestational diabetes mellitus (GDM). However, the most optimal type of nutritional intervention to prevent GDM in high-risk women is not clearly defined. This study investigates if nutritional treatment based on the Mediterranean diet (MedDiet) before 12th gestational week (GW) in women at high risk due to a body mass index (BMI)≥25kg/m2, reduces the rate of GDM and metabolic syndrome (MetS) at 3 years postpartum. We performed a post-hoc analysis of the San Carlos Gestational Prevention Study. A total of 735 women with BMI≥25kg/m2 were evaluated between 2015-2018, 246 in standard diet control group (CG) and 489 in MedDiet intervention group (IG). The rate of GDM was significantly lower in IG compared to CG (25.1%vs31.7%;p=0.037). Postnatal follow-up was completed by 141 women in CG (57%) and 312 women in IG (64%). At 3 years postpartum, we observed a reduction (relative risk 95% confidence interval) in the rates of impaired fasting glucose (IFG) (0.51 (0.28-0.92);p=0.019), obesity (0.51 (0.28-0.92),p=0.041), waist circumference (WC)≥89.5cm (0.54 (0.31-0.94);p=0.022) and MetS (0.56 (0.33-0.94);p=0.003). MedDiet reduces the rate of GDM and postpartum MetS in women with BMI)≥25kg/m2, suggesting that its implementation should be routinely recommended from the first GWs.

Following the detection of highly pathogenic avian influenza (HPAI) virus in countries bordering Kenya to the west, we conducted surveillance among domestic and wild birds along the shores of Lake Victoria. In addition, between 2018 and 2020, we conducted surveillance among poultry and poultry workers in live bird markets and among wild migratory birds in various lakes that are resting sites during migration to assess introduction and circulation of avian influenza viruses in these populations. We tested 7,464 specimens (oropharyngeal and cloacal swabs) from poultry and 6,531 fresh fecal specimens from wild birds for influenza A viruses by real-time RT-PCR. Influenza was detected in 3.9% (n=292) of specimens collected from poultry and 0.2% (n=10) of fecal specimens from wild birds. On hemagglutinin subtyping, most of the influenza A positives from poultry (274/292, 93.8%) were H9. Of 34 H9 specimens randomly selected for further subtyping, all were H9N2. On phylogenetic analysis, these viruses were genetically similar to other H9 viruses detected in East Africa. Only two of the ten influenza A positive specimens from the wild bird fecal specimens were successfully subtyped; sequencing analysis of one specimen collected in 2018 was identified as low pathogenicity avian influenza H5N2 virus of the Eurasian lineage and the second specimen, collected in 2020, was subtyped as H11. A total of 18 OP/NS swabs from poultry workers with ARI (12%) were collected; none were positive for influenza A virus. We observed significant circulation of H9N2 influenza viruses in poultry in live bird markets in Kenya. During the same period, low pathogenic H5N2 virus was detected in a fecal specimen collected in a site hosting a variety of migratory and resident birds. Although HPAI H5N8 was not detected in this survey, these results highlight the potential for introduction and establishment of highly pathogenic avian influenza viruses in poultry populations and the associated risk of spillover to human populations.

Dehydration of hydrogen gas is one of the important steps in many industrial purposes thus, drying systems have been developed with high-efficiency and relative effect. In this article, the basic principles and design of a three-bed TSA (Temperature Swing Adsorption) dryer for dehydration operation of hydrogen gas drying are described in detail. The text commences with an in-depth explanation of the basic principles behind TSA technology such as adsorption and desorption mechanisms, thermodynamic considerations and material selection for adsorbents. This paper also deals with the detailed design of a three-bed TSA dryer, explaining about various fabricating details that influences both performance and total operability. The third part focuses the operational phase, and especially in cycle time, regeneration strategy and efficiency of energy. Advanced optimisation techniques are employed to lower energy consumption, increase throughput capacity and improve overall system. This detailed study will be of great help for engineers and investigators working on TSA systems design and optimization to dehydrate hydrogen gas, contributing towards the betterment in this important field dealing with industrial gas processing.

In the field of Natural Language Processing (NLP), Large Language Models (LLMs) have shown great potential in document-level event extraction tasks, but existing methods face challenges in the design of prompts. To address this issue, we propose an optimization strategy called "Definition-driven Document-level Event Extraction (DDEE)." By adjusting the length of the prompt and enhancing the clarity of heuristics, we have significantly improved the event extraction performance of LLMs. We used data balancing techniques to solve the long-tail effect problem, enhancing the model's generalization ability for event types. At the same time, we refined the prompt to ensure it is both concise and comprehensive, adapting to the sensitivity of LLMs to the style of prompts. In addition, the introduction of structured heuristic methods and strict limiting conditions has improved the precision of event and argument role extraction. These strategies not only solve the prompt engineering problems of LLMs in document-level event extraction but also promote the development of event extraction technology, providing new research perspectives for other tasks in the NLP field.

This paper aims to demonstrate that, beyond the small world of Riemann-Liouville and Caputo derivatives, there is a vast and rich world with many derivatives suitable for specific problems and various theoretical frameworks to develop, corresponding to the different paths taken. Notions of time and scale sequences are introduced and general associated basic derivatives, namely right/stretching and left/shrinking, are defined. A general framework for fractional derivative definitions is reviewed and applied to get both known and new fractional order derivatives. Several fractional derivatives are considered, mainly: Liouville, Hadamard, Euler, bilinear, tempered, q-derivative, and Hahn.

Background: Across the world, antibiotic resistance is a critical challenge. To address such a problem, it has to be done to investigate new antibiotic sources. Aim of the study: Study of the antibacterial activity of Corallopyronin A in preclinical animal testing and randomized human clinical trials stages 1/2, as well as investigating the purification of Corallopyronin A from different soil conditions in Egypt. Type of the study: Screening experimental study. Methodology: Egypt's various soil conditions were tested to develop bacterial isolates that produced the antibiotic compound Corallopyronin A. Reversed phase HPLC was used to purify Myxopyronin A. The broth microdilution method and the paper disc diffusion assay determined the test antibiotic's minimum inhibitory concentration( MIC) and in vitro antibacterial activity. Moreover, in vivo antibacterial spectrum, adverse medication responses, and pharmacokinetics were found in phases 1/2 of randomized clinical studies involving humans and animal models. Results: Corallopyronin A was generated from the culture supernatant of the soil bacterial isolate Corallococcus coralloides M2, cultivated on a Casein yeast peptone( CYP) plate. The test antibiotic prevented the growth of several Gram-ve bacteria, including Escherichia coli, at MICs higher than 100 mcg/ ml; while blocking the development of many Gram +ve bacteria, with MICs ranging from 3 to 15 mcg/ ml. However, eukaryotic cells—such as those found in fungi and humans—were unaffected. A bactericidal consequence of the test antibiotic was detected in the inhibition of prokaryotic DNA-dependent RNA polymerase( RNLP). Conclusion: The synthesis of the bactericidal antibiotic Corallopyronin A from Corallococcus coralloides M2 isolated from different soil settings in Egypt intrigued the current investigation.

The risk of a fatal outcome was 41% in unvaccinated patients (p = 0.713), which increased by 2.66% with co-infection with two pathogens (p = 0.342) and by 26% with three pathogens (p = 0.005). Additionally, 50% of ICU patients had a triple infection, compared with only 1.3% in the inpatient unit (p = 0.0029). The risk of death and/or ICU admission was 12 times higher (p = 0.042) with an additional pathogen and increased by 95% (p = 0.003) with a third concomitant pathogen. Regular multiplex testing is important for prompt treatment and targeted antibiotic use.

Considering the worldwide impact of heart failure, it is crucial to develop approaches that can help us comprehend its root cause and make accurate predictions about its outcome. This is essential for lowering the suffering and death rates connected with this widespread illness. Cardiomyopathies frequently result from genetic factors, and the study of heart failure genetics is advancing quickly. Dilated cardiomyopathy (DCM) is the most prevalent kind of cardiomyopathy, encompassing both hereditary and nongenetic abnormalities. It is distinguished by the enlargement of the left ventricle or both ventricles, accompanied by reduced contractility. The discovery of the molecular origins and subsequent awareness of the molecular mechanism is broadening our knowledge of DCM development. Additionally, it emphasizes the complicated nature of DCM and the necessity to formulate several different strategies to address the diverse underlying factors contributing to this disease. Genetic variations that can be transmitted from one generation to another can be a significant contributor to causing family or isolated DCM. Genetic variation also plays a significant role in determining susceptibility for acquired triggers for DCM. The genetic causes of DCM can have a diverse range of phenotypic expressions. It is crucial to select the most probable patients to have advantages from genetic testing. The purpose of this research is to emphasize the significance of identifying genetic DCM, the crucial relationships between genotype and phenotype, and the usefulness of genetic testing in the therapeutic care of both those affected and their relatives. This approach is expected to gain importance once treatment is guided by genotype-specific advice and disease-modifying medications.

Insect larvae production offers the potential for large-scale synthesis of high quality protein that can be used as feed or food. However, currently, there are limitations on the source of substrates for the insect larvae to use. One concern is the potential survival of animal pathogens within insect larvae if their feed is contaminated. In this study, the survival of a very stable virus, porcine parvovirus (PPV), within mealworm (Tenebrio molitor) and black soldier fly (BSF) (Hermetia illucens) larvae has been analyzed after oral ingestion of the virus. The PPV DNA genome could be readily detected by PCR in both types of larvae up until 9 days post ingestion (DPI), the end of the study period. Furthermore, infection of susceptible PK15 cells by PPV from homogenized mealworm larvae could be detected until at least 3 dpi, using an immunoperoxidase staining method, and up until 9 DPI using a more sensitive real time PCR assay. Thus, PPV can remain infectious within mealworm larvae during their main growth phase through to their harvesting. However, it may be considered that PPV is exceptional in this respect since it displays unusual stability, e.g. to heat.

Aiming to address the issue that the existing multi-view stereo reconstruction methods have insufficient adaptability to the repetitive patterns and weak textures in the multi-view images, this paper proposes a three-dimensional (3D) reconstruction algorithm based on feature enhancement and weight optimization MVSNet (Abbreviated as FEWO-MVSNet). To obtain accurate and detailed global and local features, we first develop an adaptive feature enhancement approach to obtain multi-scale information from the images. Second, we introduce an attention mechanism and a spatial feature capture module to enable high-sensitivity detection for weak texture features. Third, based on the 3D convolutional neural network, the fine depth map for multi-view images can be predicted and the complete 3D model is subsequently reconstructed. Last, we evaluated the proposed FEWO-MVSNet through training and testing on the DTU, BlendedMVS, and Tanks&amp;Temples datasets. The results demonstrate significant superiorities of our method for 3D reconstruction from multi-view images, with our method ranking first in accuracy and second in completeness when compared to the existing representative methods.

In traffic scene, pedestrian target detection faces significant issues of misdetection and omission due to factors such as crowd density and obstacle occlusion. To address these challenges and enhance detection accuracy, we propose an improved CCW-YOLO algorithm. The algorithm first introduces a lightweight convolutional layer using GhostConv and incorporates an enhanced C2f module to improve the network's detection performance. Additionally, it integrates the Coordinate Attention module to better capture key points of the targets. Next, the bounding box loss function CIoU Loss at the output of YOLOv5 is replaced with WiseIoU Loss to enhance adaptability to various detection scenarios, thereby further improving accuracy. Finally, we develop a pedestrian count detection system by using PyQt5 to enhance human-computer interaction. Experimental results on the INRIA public dataset show that our algorithm achieves a detection accuracy of 95.6%, representing a 8.7% improvement over the original YOLOv5s algorithm. This advancement significantly enhances the detection of small objects in images and effectively addresses misdetection and omission issues in complex environments. These findings have important practical implications for ensuring traffic safety and optimizing traffic flow.

Most of the existing trajectory privacy protection methods provide a unified degree of privacy protection for data, and most of the methods mainly focus on the spatial and temporal dimensions of trajectory data, with little consideration of the semantic information of the location. To address these issues, we propose a hierarchical temporal semantic tree-based personalized trajectory privacy protection (HTST-PTPP) scheme, which mainly constructs a hierarchical temporal semantic tree by considering semantic categories and residence time. Then, quantifies the privacy protection requirements of each location, divides the privacy level, and uses differential privacy technology to realize personalized trajectory privacy protection. Finally, experiments are carried out on two real data sets. The experimental results show that our HTST-PTPP scheme has good performance in data availability and privacy protection.

Crowd abnormal behavior recognition is one of the research hotspots in computer vision. Its goal is to use computer vision technology and abnormal behavior detection models to accurately perceive, predict, and intervene in potential abnormal behaviors of the crowd, and monitor the status of the crowd system in public places in real-time, to effectively prevent and deal with public security risks and ensure public life safety and social order. To this end, focusing on the crowd abnormal behavior recognition technology in the computer vision system, a systematic review study of its theory and cutting-edge technology is conducted. First, the crowd level and abnormal behaviors in public places are defined, and the challenges faced by crowd abnormal behavior recognition are expounded. Then, from the dimensions based on traditional methods and based on deep learning, the mainstream technologies of abnormal behavior recognition are discussed, and the design ideas, advantages, and limitations of various methods are analyzed. Next, the mainstream software tools are introduced to provide a comprehensive reference for the technical framework; Secondly, typical abnormal behavior datasets at home and abroad are sorted out, and the characteristics of these datasets are compared in detail from multiple perspectives such as scale, characteristics and uses, and the performance indicators of different algorithms on the datasets are compared and analyzed; Finally, the full text is summarized and the future development direction of crowd abnormal behavior recognition technology is prospected.

Waste cooking oil (WCO) recycled asphalt is facing issues regarding insufficient thermal oxidation stability and aging resistance. In this research, glycerol esterification was adopted to pretreat WCO, and the consequences of this treatment on the aging resistance and thermal stability of WCO were analyzed. The impacts of varying levels of esterification of WCO on the high-temperature, low-temperature performances, fatigue properties, as well as aging resistance of recycled asphalt were investigated. Furthermore, the mechanisms of regeneration and anti-aging of deeply esterified WCO recycled asphalt were revealed by Fourier transform infrared spectroscopy (FTIR) and gel permeation chromatography (GPC) tests. The results indicated that variations in the physical properties of WCO during the aging process were reduced, and its aging resistance was improved following glycerol esterification therapy. The initial thermal decomposition temperature was increased by approximately 115°C, which resulted in the enhancement of thermal stability significantly. Recycled asphalt obtained from deeply esterified WCO exhibited superior high-temperature, low-temperature performances and fatigue properties. Moreover, the thermal oxidation stability and aging resistance of recycled asphalt with deep-esterified WCO could be promoted by reducing the oxidation and volatilization of light components during the aging process.

Background: Diagnostic accuracy of Parkinson’s disease (PD), a synucleinopathy, based on diagnostic criteria is suboptimal. A biomarker for synucleinopathies is pivotal both from a clinical and from a research aspect. CSF a-synuclein has been extensively studied over the past two decades as a candidate biomarker of synucleinopathies. Herein we present data on studies focusing on total, phosphorylated and oligomeric CSF a-synuclein in PD. Methods: Pubmed, Scopus and Web of Science were searched for studies with &gt;10 PD patients and control subjects, with data (mean, SD) on total, phosphorylated or oligomeric a-synuclein. Cohen’s d, as a measure of effect size, was calculated for all a-synuclein forms. Subgroup analysis and meta-regression were performed in an effort to explain between-study heterogeneity. Results: Thirty studies on total, six studies on oligomeric and one study on phosphorylated a-synuclein were included. Total a-synuclein was decreased and oligomeric a-synuclein increased in PD patients vs. controls. Effect size was medium for total and high for oligomeric a-synuclein. A-syn forms provided suboptimal combined sensitivity/specificity for the differentiation of PD from controls. There was significant between-study heterogeneity. PD cohort characteristics (sex, age, disease duration, UPDRS, H&amp;Y) and study characteristics (study design, healthy vs. neurological controls, control for CSF blood contamination, method of a-syn measurement) could not account for between-study heterogeneity. Publication bias was limited. Conclusions: CSF a-synuclein levels lack sufficient accuracy to be used as biomarkers for PD. Standardization of (pre)analytical variables may improve the discriminatory power of a-synuclein forms in the future.

With the rapid consumer adoption of mobile devices such as tablets and smart phones, the tele-traffic has experienced a tremendous growth, low power technologies are highly desirable for future communication networks. In this paper, we consider an ambient backscatter (AB) based user cooperation (UC) scheme for mmWave wireless powered communication networks (WPCN) with lens antenna arrays. Firstly, we formulate an optimization problem to maximize the minimum rate of two users by jointly designing power and time allocation. Then we introduce auxiliary variables and transform the original problem into a convex form. Finally, we propose an efficient algorithm to solve the transformed problem. Simulation results demonstrate that the proposed AB based UC scheme outperforms the competing schemes, thus improve the fairness performance of throughput in WPCN.

Autoimmune blistering diseases represent a group of chronic severe, disabling, potentially fatal disorders of the skin and/or mucous membranes primarily mediated by pathogenic auto-antibodies. Despite their rarity, these diseases are associated with significant morbidity and mortality, a profound negative impact on the patient’s quality of life and impose a considerable economic burden. Rituximab, an anti CD-20 monoclonal antibody represents the first line of therapy for pemphigus, regardless of its severity as it ensures high rates of rapid, long-lasting complete remission. Nevertheless, disease recurrence is the rule, all patients requiring maintenance therapy with rituximab sooner or later. While innate resistance to rituximab in pemphigus patients is exceptional, acquired resistance is frequent and may develop even in patients with initial complete response to rituximab, representing a real challenge for physicians. We discuss the various resistance mechanisms and their complex interplay, as well as the numerous therapeutic alternatives that may be used to circumvent rituximab resistance. As no therapeutic measure is universally efficient, individualization of rituximab treatment regimen and tailored adjuvant therapies in refractory pemphigus cases are mandatory.

Drought affects human and natural systems, human and animal life and health, and socioeconomic activities. Drought consequences depend on its type and class, but also on the preparedness and resistance of communities to this climate disturbance. In the last decades, droughts accounted for about 16% of the total number of disasters but were responsible for 95% of the number of deaths and 26% of economic losses in Africa. This study aims to assess the drought regime in Southern Africa based on drought and vegetation indices. The SPI and SPEI were calculated at different timescales, using ERA5 data for the 1971 – 2020 period. The spatiotemporal distribution of drought descriptors was analyzed and compared with the patterns of the NDVI, EVI and VCI vegetation indices. The results reveal (i) the occurrence of droughts of various classes and at different timescales throughout the study period and region, (ii) high spatial variability in the number, duration, severity and intensity of drought, which tends to decrease with increasing timescale, (iii) high spatial-temporal agreement between drought and vegetation indices that confirm the dryness of vegetation during drought. These results aim to support policymakers in defining legislation to manage drought and water resources.

Ferritin is an indirect marker for total body iron stores. Comparison of the ferritin concentrations in the meconium with the concentrations of proteins regulating iron metabolism could aid better understanding of principles behind the adjustment between the fetal iron pool and newborn body size. Ferritin, transferrin, haptoglobin, ceruloplasmin, lactoferrin, myeloperoxidase, neutrophil gelatinase-associated lipocalin (NGAL) and calprotectin concentrations were measured by ELISA in meconium samples from 122 neonates. The neonates were classified according to the meconium ferritin tertiles and the values were collated with the meconium concentrations of other proteins and newborn body weight and length measurements. Increasing ferritin concentrations in meconium in consecutive tertiles (p < 0.05) were parallel to increased NGAL concentrations (p < 0.05). The interrelationships between the meconium concentrations of transferrin, haptoglobin and NGAL as well as between myeloperoxidase, calprotectin and lactoferrin are maintained in all subsequent tertiles of ferritin concentrations, (p < 0.05). In contrast to ferritin, increasing meconium NGAL concentrations in consecutive tertiles were linked to increased concentrations of transferrin, haptoglobin, lactoferrin and myeloperoxidase (p < 0.05) and of calprotectin, ferritin and ceruloplasmin (p < 0.1). Meconium ceruloplasmin concentrations correlate exclusively with neutrophil granule proteins, i.e. myeloperoxidase, NGAL, lactoferrin and calprotectin (p < 0.05). Meconium ferritin concentrations negatively correlates with birth weight (r= -0.20) and length (r= -0.31) of neonates, whereas NGAL concentrations just with birth length (r= -0.26). The remaining proteins did not show such relationships with the size of the newborn. High meconium concentrations of both ferritin and NGAL may specifically characterize neonates of smaller size. High meconium concentrations of both ferritin and NGAL may specifically characterize neonates with lower body measurements. Correlations between meconium transferrin, haptoglobin and NGAL may confirm the interrelationships of these proteins for proper iron control and transport in the intrauterine environment. Meconium ceruloplasmin concentrations may reflect the control of neutrophil activity in utero.

Chronic stress, culminating in burnout, evolves gradually and is notoriously difficult to detect due to vague symptoms and individuals' hesitance to acknowledge their struggles. To expedite the identification and recognition of this condition, enabling timely psychological intervention, the integration of Artificial Intelligence (AI) is increasingly considered. This research does not assert the feasibility of an AI system managing all aspects of chronic stress's impact. However, it highlights the capability of current technology to detect stress indicators based on quantifiable data like Heart Rate (HR) and organizational climate dimensions. Although other physiological markers such as oximetry, skin galvanic response, and EKG have been explored, they have not shown reliable differentiation between stress and joy. Focused on the unique context of school principals in the Bedouin regions of Israel, this study investigates the interplay between HR, organizational climate, and stress levels. It introduces a novel application of a fuzzy logic tool that combines HR and organizational climate metrics to aid in stress diagnosis. This tool incorporates the psychologist's expertise to provide real-time data crucial for developing effective coping strategies. While the AI-supported fuzzy system does not replace professional psychological intervention, it significantly enhances the speed of condition identification and intervention planning, thus shortening the response time to stress-related issues in educational leadership within culturally specific settings. The application of such AI-driven tools is pivotal for sustaining the well-being and effectiveness of educational leaders, thereby supporting the broader goal of educational sustainability.

Systematic reviews represent a powerful instrument to summarize the existing evidence in medical literature. However, articles for a systematic review are hard to identify, and mostly require a structured search of the literature through a number of databases, using keyword-based search strategies, followed by the painstaking manual selection of pieces of evidence that are pertinent to the query. A.I. algorithms may offer solutions to reduce the workload on investigators. We applied BERTopic, a newer and much-recognized transformer-based topic-modeling algorithm, to two datasets of 6137 and 5309 articles of newly published systematic reviews in the area of peri-implantitis and bone regeneration in implant dentistry. In the two datasets, BERTopic identified 14 and 22 clusters, respectively, and it automatically created labels describing the nature of the topics for each individual cluster based on semantic interpretation of their titles. Most themes regarded the query theme, but in both conditions, BERTopic also uncovered articles related to off-themes, which composed around 30% of the dataset—with sensitivity up to 0.79 and specificities of at least 0.99. Our results suggest that adding a topic-modeling step to the screening process could potentially save working hours for researchers involved in systematic reviews of the literature.

Soft magnetic composites cores were produced by Spark Plasma Sintering (SPS) from Ni3Fe@ZnFe2O4 and NiFeMo@ZnFe2O4 pseudo-core-shell powders. In the Fe-Ni alloys@ZnFe2O4 pseudo-core-shell composite powders, the core is a large nanocrystalline Permalloy or Supermalloy particle obtained by mechanical alloying, and the shell is a pseudo continuously layer of Zn ferrite particles. The pseudo-core-shell powders have been compacted by SPS at temperatures between 500-700 ºC, with a holding time of 0 minutes. Several techniques were used for the characterisation of the powders and sintered compacts: X-ray diffraction, scanning electron microscopy, energy dispersive X-ray spectroscopy, magnetic hysteresis measurements (DC and AC) and electrical resistivity. The electrical resistivity is stabilised at values of about 7·10-3 Ω·m for sintering temperatures between 600-700 °C and this value is 3 orders of magnitude higher than the electrical resistivity of sintered Fe compacts. The best relative initial permeability was obtained for the Supermalloy/ZnFe2O4 composite compacts sintered at 600 ºC, which decreases linearly for the entire frequency range studied, from around 95 to 50. Up a frequency of 2,000 Hz the power losses are lower than 1.5 W/kg. At the frequency of 10 kHz, the power losses are larger, but they remain at a low level. In the case of Supermalloy/ZnFe2O4 composite compact SPS-ed at 700 °C, the specific power losses are even lower than 5 W/kg. The power losses decomposition proved that intra-particles losses give the main part of the losses.

Geothermal energy, being a clean energy source, has immense potential, and accurate wellbore modeling is crucial for optimizing the drilling process and ensuring safety. This paper presents a novel geothermal wellbore model based on the drift-flux approach, tested under three different temperature and pressure well conditions. The proposed model integrates the conservation equations of mass, momentum, and energy, incorporating the gas-liquid two-phase flow drift-flux model and heat transfer model. Key features include handling heat transfer between the for-mation and the wellbore, addressing the slip relationship between gas and liquid phases, and accounting for wellbore friction. The nonlinear equations are discretized using the finite differ-ence method, and the highly nonlinear system is solved using the Newton-Raphson method. Numerical simulation, validation, and comparison with existing models demonstrate the en-hanced accuracy of this model. In our tests, the model achieved high accuracy in calculating bottom hole pressure and temperature, with Mean Relative Errors (MRE) significantly lower than those of other models. These results offer valuable insights for optimizing drilling parameters and ensuring drilling safety. Comparisons indicate that this approach significantly outperforms others in capturing the complex dynamics of geothermal wellbores, making it a superior tool for geo-thermal energy development.