A multiscale model that enables quantitative understanding and prediction of the size effect on scattering properties of micro- and nanostructures is crucial for the design of LED surface textures optimized for high light extraction efficiency (LEE). In this paper, a hybrid process for combining full-wave finite-difference time-domain simulation and a ray-tracing technique based on a bidirectional scattering distribution function model is proposed. We apply this method to study the influence of different pattern sizes of a patterned sapphire substrate on GaN-based LED light extraction from the microscale to the nanoscale. The results show that near-wavelength–scaled patterns with strong diffraction are not expected to enhance LEE. By contrast, microscaled patterns with optical diffusion behavior have the highest LEE at a specific aspect ratio, and subwavelength-scaled patterns that have antireflection properties show marked enhancement of LEE for a wide range of aspect ratios.

This paper presents the second stage of a tandem fixed wing unmanned aerial vehicle (UAV) aerodynamic development. In the initial stage, the UAV was optimized analyzing its characteristics only in symmetrical flight conditions. Posted requirements were that both wings should produce relevant positive lift, the initial stall must occur on the front wing first, the center of pressure should be close to the center of gravity, while longitudinal static stability should be in the optimum range. Computational fluid dynamics (CFD) analyses were performed, where applied calculation model was derived from the authors’ previous successful projects. The eight version TW V8 has satisfied all longitudinal requirements. Lateral-directional CFD analyses of V8 showed that the ratio of the lateral and directional stability at the nominal cruising regime was optimal, but both lateral and directional static stabilities were too high. On further development versions the lower vertical tail was eliminated, negative dihedral was implemented on the front wing, and four inverted blended winglets were added. Version TW V14 has largely improved lateral and directional stability characteristics, while their optimum ratio at cruising regime was preserved. Longitudinal characteristics were also well preserved. Maximum lift coefficient and lift-to-drag ratio were increased, compared to the V8.

It is an utmost importance to characterize drug candidates as early in the development pipeline as possible. Appropriate application of the emerging high throughput analytical techniques unlocks the opportunities to obtain experimental data for in vitro absorption, distribution, metabolism and elimination (ADME) profiling of large compound libraries which is crucial for selection of lead compounds. In an usual scenario, only one drug candidate will be selected from thousands of early compounds based on several stability and screening results. A high to medium throughput screening approaches could significantly accelerates the subsequent research and production phases. Traditionally, the analysis of metabolic stability assays heavily relies on high throughput LC-MS/MS techniques to meet with the lead profiling demands. In this study presented an innovative experimental approach that can offer a refreshing alternative. Laser Assisted Rapid Evaporative Ionization Mass Spectrometry (LA-REIMS) is a quick and efficient method for characterizing complex biological samples without laborious sample preparation and chemical separation. Therefore, using an automated LA-REIMS well plate reader as fast as 8 seconds per sample, we assessed the oxidative metabolic stability of active agents using biomimetic metalloporphyrin-based oxidative model reactions at various pH for commercially available drug substances and compared stability measurements with traditional HPLC-DAD-MS results.

The mortality of birds resulting from collisions and electrocutions with overhead lines, such as power lines, and phone line among others, has been implicated in the decline of various avian species globally. Specifically, overhead line collisions pose a significant threat to the conserva-tion of the Canarian houbara bustard (Chlamydotis undulata fuertaventurae), an endangered sub-species endemic to the Canary Islands. This study centres on the postmortem findings of Canarian houbara bustards that have collided with overhead lines, providing insights into the post-collision outcomes for these birds. A com-plete standardized necropsy of nine Canarian houbara bustards revealed that polytrauma was the cause of death in all cases. The most notable gross lesions associated with trauma included bone fractures, soft tissue lacerations, haemorrhages, luxations, and hemocoelom, with certain body regions being more frequently affected. Histopathology, immunohistochemistry, and en-tomology analysis confirmed that numerous birds survived the initial trauma, exhibiting varia-ble survival intervals before succumbing to their injuries. We concluded that when a houbara bustard collide with an overhead line it frequently survives the initial trauma. The histopathology, immunohistochemistry, or entomologic analysis may be helpful to approximate the timing interval between trauma and death.

With the existence of several programming languages such as C/C++, Java, C#, LISP, Prolog, Python, Simula, F#, Go, Haskell, Scala, Ruby, Dart, Swift, Groovy etc. and diverse paradigms like structured, object-oriented, list, aspect-oriented, service-oriented, web, mobile and logic programming, there is a need to perform an exhaustive comparative analysis of diverse compilers and environments before making a choice of implementation technology in software engineering. Optimization of compilers helps to reduce execution time by making use of high speed processor registers, thereby, eliminating redundant computation. This paper reports some series of performance analysis done with some popular programming languages including Java, C++, Python and PHP. Programs involving recursive and iterative functions like factorial of large numbers and binary search of large arrays were run on the various platforms with the execution time recorded in milliseconds and represented in a chart. This can aid in making a selection of the appropriate language to use for a given application domain.

Dielectric elastomers, such as thermoplastic polyurethanes (TPU), are widely used as dielectric layer, emulation layer and substrate of flexible and stretchable devices. To construct capacitors and actuators that work stably upon deformation, it has become an urgent need to investigate the evolution of dielectricity under stress and strain. However, the lack of effective methods for estimating the dielectric constant of elastomers under strain poses a big challenge. This article reports a device for in-situ measuring the dielectric constant of TPU under strain. It is found that upon stretching TPU to a strain of 400%, its dielectric constant decreases from 8.47 to 2.94. In addition, combined Fourier-transform infrared spectroscopy, X-ray scattering technique, and atomic force microscopy have been utilized to characterize the evolution of microstructure under strain. The investigation under tensile strain reveals that a decreased density and average size of polarized hard domains, along with a tendency of the molecular chains to align in parallel with the tensile stress. The evolution of the microstructures results in a reduction of the dielectric constant parallel to the electric field in TPU. Our work provides valuable experimental reference for improving the stability of flexible sensors and actuators based on dielectric elastomers.

Metabolic engineering in plants offers powerful strategies to enhance crop yield and quality, addressing global challenges in agriculture and food security. This study explores cutting-edge approaches in manipulating primary and secondary metabolic pathways, utilizing advanced genetic modification tools to improve key traits in crops. We examine successful applications that have enhanced photosynthetic efficiency, nutrient use, stress tolerance, and the production of valuable metabolites. The study also delves into emerging trends, such as synthetic biology approaches and multi-gene trait stacking, which are revolutionizing the field. By integrating omics technologies and computational modeling, researchers are optimizing metabolic engineering designs with unprecedented precision. As the field rapidly evolves, we consider the regulatory and biosafety aspects of genetically modified crops, providing insights into the future of sustainable agriculture and crop improvement.

This research focuses on the development of a foot-worn device to assist individuals with limited mobility in walking. The device aims to reduce the risk of accidents by closely moni-toring the wearer's movements and detecting potential hazards. It incorporates sensors, in-cluding the MPU6050 gyro sensor and KY-031 vibration sensor, to track the wearer's walking behavior. In case of abnormalities, such as falls, the device triggers an auditory alert and noti-fies the caregiver via LINE Notify. The system is controlled by the Node MCU ESP8266, enabling seamless integration with the Internet of Things (IoT). The objective of this study is to design an IoT system for medical assistance. The researchers created a prototype of a smart ankle device capable of detecting falls and sending notifications to the user's smartphone. The effectiveness of the notification system was evaluated using the Line Notify application. Re-sults demonstrated a successful detection of falls in 48 out of 50 trials, with two instances of false alarms during normal walking. The overall efficiency of the smart ankle device was 98%. In summary, the proposed smart ankle device demonstrates promising potential for var-ious applications in fall detection and safety alert systems. Further improvements and collab-orations with healthcare experts are recommended to enhance its performance and make it commercially viable. The device's connectivity and responsiveness to IoT systems are vital aspects to be considered. Future research should aim to develop additional features in collab-oration with physiotherapists and healthcare professionals to meet user requirements. The de-vice holds significant benefits in terms of fall detection and safety alerts, and efforts should be made to enhance its durability, robustness, and commercialization prospects.

In this paper, the ratio of gross agricultural production (GAP) and agricultural carbon emission is defined as agricultural carbon emission efficiency (ACEE). Considering rural labor transfer (RLT) increases the agricultural machinery intensity (AMI), the two are substitutes for each other and may interact with agricultural carbon emission efficiency (ACEE), we constructed a Simultaneous Equations Model (SEM) of ACEE, RLT and AMI, and analyzed the interaction mechanism of these three variables by using the Three-Stage Least Squares (3SLS) method to solve the endogeneity of the model. The following conclusions are drawn. First, RLT and AMI significantly promote the improvement of ACEE, while the improvement of ACEE and AMI further promotes RLT. Secondly, the causal relationship and influence mechanism of ACEE, RLT and AMI are interactive and multi-directional. An increase in AMI promotes ACEE, but an increase in ACEE inhibits an increase in AMI, suggesting that the marginal rate of substitution of machinery for labor is decreasing. Finally, China has significant regional heterogeneity. Labor transfer and machinery are only direct factors in increasing ACEE, while factors such as economic base, technology level and farmers' attitudes provide environmental support for the effective improvement of ACEE.

Based on literature data, an analysis was conducted on the thermodynamic and kinetic dependencies of the thermal decomposition of methane. Course of this process was analysed for both thermal and thermal-catalytic conditions. The elementary reaction, i.e. the synthesis of methane from its elements, including its reversibility, was used as the basis for the for considerations on the kinetic model. The conversion degree was adopted as the kinetic parameter (kinetic variable) since this measure is essential for determining the amount of carbon deposit formed and thus closing the mass balance of this process. Several different kinetic models for the elementary reaction were analysed to determine how do they relate in regard to the constant of the reaction rate. It was determined that regardless of whether the process is catalytic or purely thermal, for temperatures t>900°C, the influence of reversibility of the reaction, has negligible influence on the yield of hydrogen produced, and thus can be omitted from the kinetic models. Special attention was given to iron-based catalysts, analysing the reactivity of Fe/C systems. It was demonstrated that the determined kinetic parameters satisfy the Kinetic Compensation Effect (KCE). Furthermore, by incorporating elements of Transition State Theory (TST), the existence of Entropy-Enthalpy Compensation (EEC) was highlighted. Based on these findings Authors show that through analysis of the changes in activation energy (E=20–421 kJ·mol-1) only an estimate of the optimal process conditions can be found, because the isoconversional temperature is also dependent on the way in which the reaction is conducted (T_{iso}=1200-1450K\ >\ \ T_{eq}). In other words, it was found that strong influences of such factors as T, P, etc. can locally compensate each other. Finally, it was also shown that the relations between KCE and EEC complement each other, which is confirmed by the determined average activation entropy at the isokinetic temperature (∆SB= -275.0 J·(mol·K)-1).

:. Background and Objectives: Pulmonary embolism, PE, incidence had been increasing in the last ten years. Computed thoracic pulmonary angiography, CTPA, had a major role in confirming PE di-agnosis.The main purpose of the study was to establish the prognostic value of a CTPA parameter: pulmonary artery obstruction index, PAOI, for PE risk assessment . A second objective of the re-search was to investigate the predictive accuracy of biomarkers (D-dimer, and cardiac Troponin T, c-TnT ), and PAOI, in 7-day mortality. The third objective of the study was the relationship between PAOI, and these biomarkers, in different etiologies of PE. Materials and Methods: The study com-prised 109 patients with PE, hospitalized, and treated between February 2021, and August 2022. They had different etiologies: deep vein thrombosis, DVT; persistent atrial fibrillation, AF; chronic obstructive pulmonary disease, COPD, exacerbation; Covid; and cancers. The investigations were the following: clinical examination; D-dimer testing, as a mandatory method for PE suspicion( values ≥ 500 µg/L were highly suggestive for PE); c-TnT , as a marker of myocardial injury(values ≥ 14 ng/L were abnormal); CTPA, with right ventricle dysfunction, RVD, signs, and PAOI. Treat-ments were according to PE risk: systemic thrombolysis (in high risk , and hemodynamic instability); low weight molecular heparins, LWMH, after systemic thrombolysis, or in high risk PE, with he-modynamic stability; direct oral anticoagulants, DOAC (in low, and intermediate risk). Results: The relationship PAOI- D-dimer, and PAOI- c-TnT, had very strong statistical correlation, for the entire sample, and for DVT, AF, COPD, Covid subgroups ( Rho = 0.815-0.982). PAOI had a high predic-tive accuracy for intermediate , and high risk together (area under curve, AUC=0.948), and high risk PE (AUC= 0.993). For 7-day mortality, D-dimer , and c-TnT had high predictive accura-cy(AUC=0.921, and 0.979). PAOI had statistical significance for 7-day mortality in Covid (p=0.045), and cancer (p=0.038) patients. Conclusions: PAOI was an important tool for PE risk as-sessment. D-dimer , and c-TnT were valuable predictors, for 7-day mortality in PE. PAOI, and D-dimer; PAOI, and c-TnT were strongly correlated, for the entire PE sample, and for DVT, AF, COPD, and Covid patients.

The effect of H2S with high concentrations on catalytic dry reforming of methane (DRM) process has seldom been focused on previously. Herein, a thermodynamic analysis of the DRM reactions in the presence of H2S with the concentration varying in 0-20 vol% was conducted firstly. Several typical types of catalysts including MgO, NiO/MgO and LaNiO3 in different states were prepared for executing DRM at 800 C, 0.1 MPa in the feed of 20 vol% CO2 and 20 vol% CH4 balanced with N2. The catalytic performance of each catalyst for DRM process under conditions of absence and presence of H2S was compared. A promotion effect of increasing H2S concentration on both the conversions of CO2 and CH4 and the molar yields of CO and H2 was observed on all the catalysts especially the MgO and the pristine NiO/MgO. While a significant decline in catalytic activity of either the reduced NiO/MgO or the reduced LaNiO3 catalyst after adding H2S, moderate reactant conversions still sustained. The results of process analysis and catalyst structure characterization suggest that H2S participation can contribute to the increment in CO2 and CH4 conversion, and active S-adsorbed species may play the key role of catalysis in the reactions involving H2S.

Rapid and accurate detection of road cracks is of great significance for road health monitoring, but currently this work is mainly completed through manual site surveys. Low-altitude UAV remote sensing can obtain images with centimeter or even subcentimeter ground resolution, which provides a new efficient and economical approach for rapid crack detection. Nevertheless, crack detection networks face challenges such as edge blurring and misidentification due to the heterogeneity of road cracks and the complexity of the background. To address these issues, we propose a real-time edge reconstruction crack detection network (ERNet) which adopts multi-level information aggregation to reconstruct crack edges and improve the accuracy of segmentation between the target and background. To capture global dependencies across spatial and channel levels, we propose an efficient bilateral decomposed convolutional attention module (BDAM) that combines depth separable convolution and dilated convolution to capture global dependencies across spatial and channel levels. To enhance the accuracy of crack detection, we use a coordinate-based fusion module that integrates spatial, semantic, and edge reconstruction information. In addition, we propose an automatic measurement of crack information for extracting the crack trunk and its corresponding length and width. Experimental results demonstrate that our network achieves the best balance between accuracy and inference speed.

Plastic contamination of small dimensions (

The flowering period of rice significantly impacts variety adaptability and yield formation. Properly shortening the reproductive period of rice varieties can expand their ecological range without significant yield reduction. Targeted genome editing, like CRISPR/Cas9, is an ideal tool to fine-tune rice growth stages and boost yield synergistically. In this study, we developed a CRISPR/Cas9-mediated multiplex genome editing vector containing five genes related to three traits: Hd2, Ghd7, and DTH8 (flowering stage genes), along with the recessive rice blast resistance gene Pi21 and the aromatic gene BADH2. This vector was introduced into the high-quality Geng rice variety in Zhejiang province, Jiahe212 (JH212), resulting in 34 T0 plants with various effective mutations. Among the 17 mutant T1 lines, several displayed diverse flowering dates, but most exhibited undesirable agronomic traits. Notably, three homozygous mutant lines (JH-C15, JH-C18, and JH-C31) showed slightly earlier flowering dates without significant differences in yield-related traits compared to JH212. Through special Hyg and Cas marker selection of T2 plants, we identified 7, 6, and 2 fragrant glutinous plants devoid of transgenic components, respectively. These single plants will serve as sib lines of JH212 and potential resources for breeding applications, including maintenance lines for Xian-Geng interspecific three-line hybrid rice. In summary, our research offers practical insights and potential resources for targeted improvement of Geng rice varieties, and would also promote the Geng rice varieties expending from the southward to the northward.

The transition region is a very thin but most peculiar layer in the solar atmosphere, located between the solar chromosphere and the corona. It is a key region for understanding the coronal heating, the solar eruptions triggering, and the origin of solar winds. Here, the gradients of all physical parameters are very high, including plasma density, ionization degree, temperature, and magnetic fields, etc. Therefore, the transition region should be highly dynamic, such as fast energy releasing and transporting, plasma heating, and even particle accelerating. They include two physical aspects: thermal and non-thermal processes. The thermal processes can be observed from the ultraviolet (UV) and extreme ultraviolet (EUV) emission by multi-wavelength images. The non-thermal processes, however, should be related to radio emissions especially at millimeter wavelengths, and the frequency range should span from several GHz to beyond 300 GHz, and the emission mechanism should be highly related to the magnetic fields and variations. The ultra-wide broadband spectral observations at millimeter wavelengths with high spectral resolutions may provide rich dynamic information about the transition region, such as non-thermal energy release and transmission, the flows of plasma and energetic particles, the magnetic fields and their variations, the generation and transportation of various waves, and the formation and evolution of the source regions of solar eruptions. Here, we discussed the spectral characteristics of millimeter-wave emission from the transition region and proposed a new conception of ultra-wide broadband millimeter-wave spectrometers to observe them.

In this study, we discuss the thermospheric density response to the solar activity and QBO. By using the wavelet power spectrum method, the thermospheric density from 1967 to 2013 shows ~11-year period, semiannual and annual variations, while the seasonal variation is usually more significant under high solar activity conditions. Importantly, we investigate the possible link between the density and the QBO, with the aid of GAMDM model and different density residual method. As a result, the difference between the measured density and empirical model seemingly has QBO signal, but the ratio of them revels that the QBO signal does not exist in the thermospheric density. Comprehensively, we thought the stratospheric QBO cannot impact on the thermosphere, and more data and numerical modeling are needed for further validation.

Five fundamental problems—neutrino mass, baryogenesis, dark matter, inflation, strong CP problem—are solved at one stroke in a model, dubbed as “SM-A-S-H” (Standard Model-Axion-Seesaw-Higgs portal inflation) by Andreas Ringwald et. al. The Standard Model (SM) particle content is extended by three right-handed SM-singlet neutrinos $N_i$, a vector-like color triplet quark $Q$, a complex SM-singlet scalar field $\sigma$ that stabilises the Higgs potential, all of them being charged under Peccei-Quinn (PQ) $U(1)$ symmetry, the vacuum expectation value $v_\sigma\sim10^{11}$ GeV breaks the lepton number and the Peccei-Quinn symmetry simultaneously. We found that numerically SMASH model not only solves five fundamental problems but also the sixth problem “Vacuum Metastability” through the extended scalar sector and can predict approximately correct atmospheric neutrino mass splitting around 0.05 eV and the solar neutrino mass splitting around 0.009 eV.

In this study an adjusting post-processing approach is implemented for improving intra-hourly forecasts of solar power and ramp events of PV solar power systems at different locations in the United States. This study also serves as an out-of-sample test to evaluate the performance of the adjusting approach with different locations and timescales. Thus, various individual intra-hourly forecasts of solar power are combined and adjusted by applying the adjusting approach. Both point and probabilistic forecasts of solar power are included. After that, solar power ramp event forecasting by the adjusting approach is carried out.

To clarify effects of weathered coal humic acid on water-stable aggregates and pore characteristics of reclaimed cambisol, this research analyzed the evolution characteristics of soil aggregates and pores. Effects of different humic acid dosages (0, 1%, 3%, and 5% by weight) and application period (1 year, 2 years, and 3 years) on soil aggregates and organic carbon components in soil water-stable aggregates were investigated. The results showed that water-stable macroaggregates (>0.25 mm) had the highest content in the first year; but in the third year, water-stable microaggregates (0.053–0.25 mm) had the highest content, and silt and clay (<0.053 mm) were at a maximum. In the third year of 5% treatment, mean weight and geometric mean diameters were the largest, soil structure was the most stable, and TOC and water-stable microaggregates (0.053–0.25 mm) in soil had the highest proportions. For 5% treatment, the majority of irregular pores were independent in the first year, and number of pores decreased in the second year, but average pore volume increased, forming robust connected pores. In the third year, the number of elongated and irregular pores increased. In the third year of 5% treatment, most pores were irregular and of size >100 μm, and soil structure was the most stable.

To achieve n-type doping in diamond, extensive investigations employing first principles have been conducted on various models of phosphorus doping and boron-phosphorus co-doping. The primary focus of this study is to comprehensively analyze the formation energy, band structure, density of states, and ionization energy of these structures. It is observed that within a diamond structure solely composed of phosphorus atoms, the formation energy of an individual carbon atom is excessively high. However, the substitution of two carbon atoms leads to the conversion of diamond into a p-type semiconductor. Upon examining the P-B co-doping structure, it is revealed that the doped impurities exhibit a tendency to form more stable cluster configurations. As the separation between the freely doped atoms and the cluster impurity structure increases, the overall stability of the structure diminishes, consequently resulting in an elevation of the ionization energy. Analysis of the electronic density of states demonstrates that the electron orbit of the B atom makes negligible contributions to the impurity levels during P-B doping.

By repeated unloading and loading of the excavation dynamic and static loads, repeated train dynamic and static loads of multi-factors, the underpass tunnel, cross tunnel engineering influence area rock layer, the existing tunnel structure of the three constitutes a multifaceted structure, multi-factor interaction system. Existing tunnels into the prediction theory model of the new tunnel excavation process of dynamic and static loads, dynamic and static loads of existing tunnels are mostly analyzed individually, the results of synergistic analysis needs to be improved. Based on the theory of the current layer method, the paper comprehensively considers the stiffness of the existing tunnel, the stiffness of the new tunnel, the excavation method load and the existing tunnel load, coupled with Peck's empirical formula, the theoretical model of deformation prediction for excavation of a two-lane highway tunnel under the tunnel through the existing railroad is proposed, and verified and optimized by numerical calculations and monitoring data, which proves the applicability and reliability of the theoretical model in the similar strata and the project promotion.

The rock joint fissure slope in cold regions is prone to deformation and failure problems such as relaxation, tension and collapse under freeze-thaw (F-T) cycles. Based on the ideology of clean production and promoting the structural integrity of geotechnical projects in cold areas, this study designed and prepared aeolian-sand (AS) to replace part of river sand as a filling mortar material by taking advantage of the low cost and easy availability of AS. Investigations were carried out to determine the impact of varying proportions of AS in mortar on the microstructure and shear properties of the mortar-rock interface under F-T cycles. Therefore, F-T cycle testing, nuclear magnetic resonance (NMR) testing and shear testing were carried out on grout with different proportions of AS. The results show that the right proportion of AS replacement could enhance the shear deformation resistance and F-T resistance of the mortar-rock interface, and 30% proportion is the optimal proportion. By increasing of F-T cycles, the three types of specimens showed different degrees of particle spalling, shedding and cracking. The slurry-rock interface layer in the A (0%) group exhibited the most severe F-T deterioration, while the B (15%) group showed a lesser degree, and the C (30%) group performed the best. T2 spectrum curve and total spectrum area change law from the microscopic point of view to verify the 30% AS proportion mortar-rock interface F-T resistance is the strongest, followed by 15% AS proportion mortar, the weakest is ordinary mortar. The degradation of the mortar-rock bond is primarily due to the conversion of solid to liquid phases and the movement of internal water caused by fluctuating temperatures. The extent of F-T deterioration in the slurry-rock interface layer is greatly affected by the varying proportions of AS. The shear strength and shear stiffness of specific proportion of AS decreased with the increase of F-T cycles. For same F-T cycles, the shear strength and shear stiffness of group C (30%) were the highest, followed by group B (15%) and group A (0%). The grout material not only reinforces the F-T joint fissure slope, but also reduces the cost of grout reinforcement and promotes the clean production of geotechnical structures.

The research on the excavation mechanical properties of underpass tunnels has already had certain results, but fewer of them consider the effects of dynamic and static loads on the excavation mechanical properties of underground tunnels at the same time, especially the lack of research cases of double-line highway tunnels with angled underpasses of existing railway tunnels. In this paper, based on the tunnel project of the new double-line Shiqian Highway Tunnel passing under the Hurong Railway at an oblique angle, the mechanical parameters of the rock body in the cross-tunneling area under the influence of static and dynamic load coupling are obtained by using the disturbance quantification coefficients and the Hoek-Brown criterion based on the method of over-advanced geological prediction and the investigation of the surrounding rock on the palisade face, and the engineering-scale finite element model is constructed and the mechanical characteristics of the excavation in the tunnel of the double-lane highway tunnel passing under the existing railroad under the influence of the static and dynamic loads are analyzed. The results show that: the new tunnel rock movement law for the top of the arch sinking, bottom plate bulging, side wall to move outward, the height and width of the arch and bottom plate arch with the tunnel excavation and increase, the side wall rock displacement effect is smaller; left and right lines of the tunnel disturbed area of the rule of change is similar; the existing tunnel bottom plate displacement is more than the top plate and the left and right side walls by the excavation of the time step influence is larger. Typical profile displacement is mainly determined by the distance from the excavation surface; the new tunnel in the four types of calculation conditions of the rock disturbance angle is the same; the existing tunnel roof and side wall Von Mises stress extreme occurs in the tunnel structure, the bottom plate there are pressure relief and pressure-bearing areas; based on the displacement control criteria, the recommended upper and lower step blasting method.

The authors argue that despite significant numbers of foreign workers present in the Russian labor market Russia remains unattractive for highly skilled foreign workers. The economic crisis the country has faced since 2014 has resulted in a further outflow of foreign nationals from OECD countries. So Russia has to look for employees among newcomers from the former Soviet states, the majority of whom come from Central Asia. Russian politics with regard to immigration is characterized by the collision between “geopolitical” and domestic policy rationales. On one hand, seeking to maximize its influence in the post-Soviet space Russia provides preferential conditions of employment for citizens of partner countries in the framework of the Eurasian Economic Union. On the other hand, the Kremlin is afraid to liberalize its approach to immigration and the integration of immigrants through fear of losing popularity among the electorate. The second substantial feature of Russian immigration politics is an extreme level of securitization of migration issues. The government considers these issues primarily through a policing lens. One cannot claim that the Russian state does not take any steps to liberalize “migratory regulation”; however, the effect of these measures is being vastly reduced by new restrictions. In addition, liberally designed laws do not bring the expected results due to the corrupt practices that pervade the whole of migration regulation.

Carbamazepine (CBZ) is one of the most common emerging contaminants released to the aquatic environment through domestic and pharmaceutical wastewater. Due to its high persistence through conventional degradation treatments, is considered a typical indicator for anthropogenic activities. This study tested the removal of CBZ through two different clay-based purification techniques: adsorption of relatively large concentrations (20-500 μmol L-1) and photocatalysis of lower concentrations (<20 μmol L-1). The sorption mechanism was examined by FTIR measurements, exchangeable cations released, and colloidal charge of the adsorbing clay materials. Photocatalysis was performed in batch experiments under various conditions. Despite the neutral charge of carbamazepine, the highest adsorption was observed on negatively charged montmorillonite-based clays. Desorption tests indicate that adsorbed CBZ is not released by washing. The adsorption/desorption processes were confirmed by ATR-FTIR analysis of the clay-CBZ particles. A combination of synthetic montmorillonite or hectorite with low H2O2 concentrations under UVC irradiation exhibits efficient homo-heterogeneous photodegradation at μM CBZ levels. The two techniques presented in this study suggest solutions for both industrial and municipal wastewater, possibly enabling water reuse.

Advanced heart failure (AHF) presents a complex landscape with challenges spanning diagnosis, management, and patient outcomes. In response, the integration of multimodality imaging techniques has emerged as a pivotal approach. This comprehensive review delves into the profound significance of these imaging strategies within AHF scenarios. Multimodality imaging, encompassing echocardiography, cardiac magnetic resonance imaging (CMR), and cardiac computed tomography (CCT), stands as a cornerstone in the care of patients with both short- and long-term mechanical support devices. These techniques facilitate precise device selection, placement, and vigilant monitoring, ensuring patient safety and optimal device functionality. In the context of orthotopic cardiac transplant (OTC), the role of multimodality imaging remains indispensable. Echocardiography offers invaluable insights into allograft function and potential complications. Advanced methods, like speckle tracking echocardiography (STE), empower the detection of acute cell rejection. CMR and CCT further enhance diagnostic precision, especially concerning allograft rejection and cardiac allograft vasculopathy. This comprehensive imaging approach goes beyond diagnosis, shaping treatment strategies and risk assessment. By harmonizing diverse imaging modalities, clinicians gain a panoramic understanding of each patient's unique condition, facilitating well-informed decisions. Thus, this review underscores the irreplaceable role of multimodality imaging in elevating patient outcomes, refining treatment precision, and propelling advancements in the evolving landscape of advanced heart failure management.

Small and medium-sized family farms are the place of life and source of income for about half of the population. The aim of the analysis was to determine the relationship between Eco-Efficiency, Human Capital Efficiency in small and medium-sized family farms. The analyses were carried out using an economic measure (value of agricultural production per work hour calculated per 1 ha) and synthetic measures: human capital and environmental measures. The synthetic measures were determined using the CRITIC-TOPSIS method by defining weights for variables used in the synthetic measures. The analyses covered five countries, namely: Lithuania (960 farms), Moldova (532 farms), Poland (696 farms), Romania (872 farms), and Serbia (524 farms). All the countries qualified for analysis are characterised by a high fragmentation of agricultural holdings. The analyses carried out allowed us to formulate the following conclusions: the Eco-Efficiency and Human Capital Efficiency indexes increase with area for small and medium-sized family agricultural farms. An increase in the Eco-Efficiency index with an increase in farm area leads to a suspicion that the smaller the farm area is, the more extensive the agricultural production being carried out. In addition, an increase in human capital efficiency with an increase in the area of a farm indicates that there is inefficiency in the utilisation of human capital resources in the agricultural farms studied.

Pancreatic cancer is the fourth most common cause of cancer mortality worldwide. Furthermore, patients with pancreatic cancer experience limited benefit from current chemotherapeutic approaches because of drug resistance. Therefore, an effective therapeutic strategy for patients with pancreatic cancer is urgently required. Deguelin is a natural chemopreventive drug that exerts potent antiproliferative activity in solid tumors by inducing cell death. However, the molecular mechanisms underlying this activity have not been fully elucidated. Here we show that deguelin blocks autophagy and induces apoptosis in pancreatic cancer cells in vitro. Autophagy induced by doxorubicin plays a protective role in pancreatic cancer cells, and suppressing autophagy by chloroquine or silencing autophagy protein 5 enhanced doxorubicin-induced cell death. Similarly, inhibition of autophagy by deguelin also chemosensitized pancreatic cancer cell lines to doxorubicin. These findings suggest that deguelin has potent anticancer effects against pancreatic cancer and potentiates the anti-cancer effects of doxorubicin. These findings provide evidence that combined treatment with deguelin and doxorubicin represents an effective strategy for treating pancreatic cancer.

Vanilla planifolia is grown as a high-value orchid spice for its odor and savor attributes that increase due to the curing process associated with microbial colonization. This tends to influence the aromatic properties of vanilla. Hence, 11 Bacillus sp. strains were isolated from V. planifolia and identified with 16S rRNA gene sequencing. The liquid culture (1 mL of 107 CFU mL-1) of selected Bacillus vallismortis NR_104873.1:11-1518, B. velezensis ZN-S10, and B. tropicus KhEp-2 effectively fermented green-blanched vanilla pods kept at 10 ℃ during the sweating stage. GC-MS analysis showed that the methanol extract of non-coated, and B. vallismortis treated vanilla detected three (3) volatile compounds, whereas seven (7) components were obtained in B. tropicus and B. velezensis treatment. 4H-pyran-4-one, 2,3-dihydro-3,5-dihydroxy-6-methyl was found in B. velezensis ZN-S10, B. tropicus KhEp-2, B. vallismortis while it was not present in the control samples. This ketone compound suggested a Maillard reaction resulting in brown-increased aroma pods. Linoleic acid and Hexadecanoic acid ethyl esters were detected only in ZN-S10 strain-coated vanilla. A novel 3--Deoxy-d-mannoic lactone was detected only in B. vallismortis treated vanilla characterized as a new compound in V. planifolia which suggested that the new compound can be altered with the coating of bacteria in vanilla during fermentation. Thus, the Bacillus strains improved the volatile profile and exhibited a new aroma and flavor profile of vanilla owing to bacteria fermentation during the curing process.

Telomeres, located at the ends of each chromosome play a vital role in determining cellular fate and aging. Accelerated shortening of telomeres may also result in accelerated aging and occurrence of age-related degenerative diseases. Anti-aging treatments may help in increasing the telomere length along with improving quality of life, reducing dependency for daily life activities, increasing life expectancy and reducing the risks associated with aging. In this study, we evaluated the effect of anti-aging integrative therapy in 36 individuals. The treatment included a combination of HBOT, ozone therapy, colon hydrotherapy, etc. Telomere length was used as a biomarker for objectively quantifying the outcome of the treatment. The effect of treatment was also assessed on various aging symptoms. At the end of the treatment, it was found that that 97.22% individuals showed an increase in telomere length with an average increase of 0.43 Kbp and 94.44% individuals showed reduced biological age with an average decrease of 3.8 years. These improvements were statistically significant. Improvements were also recorded in the majority of the symptoms. No major adverse events were observed. These results indicate that antiaging integrative therapy has the potential to reverse aging symptoms, cellular aging and improve quality of life.

Gestational trophoblastic diseases (GTDs) encompass a spectrum of conditions characterized by abnormal trophoblastic cell growth, ranging from benign molar pregnancies to malignant trophoblastic neoplasms. This systematic review explores the molecular underpinnings of GTDs, focusing on genetic and epigenetic factors that influence disease progression and clinical outcomes. Based on 65 studies identified through systematic search and selection criteria, key findings include dysregulations in tumor suppressor genes such as p53, aberrant apoptotic pathways involving BCL-2, and altered expression of growth factor receptors and microRNAs. These molecular alterations not only differentiate molar pregnancies from normal placental development but also contribute to their clinical behavior, from benign moles to potentially malignant forms. The review synthesizes insights from immunohistochemical studies and molecular analyses to provide a comprehensive understanding of GTD pathogenesis and implications for personalized care strategies.

Multidrug resistant organisms (MDROs) outbreaks have been steadilyincreasing in Intensive care units (ICUs). Still, healthcare institutions and workers (HCW) reached no unanimity on how and when implementing infection prevention and control (IPC) strategies. We aimed to provide a pragmatic, physician practice-oriented, resume of strategies towards different MRDOs outbreaks in ICU. We performed a narrative review on IPC in ICUs, investigating patient-to-staff ratios, education, isolation, decolonization, screening and hygiene practices, outbreak reporting, cost-effectiveness, reproduction-number(R0), and future perspectives. The most effective IPC strategy remains unknown. Most studies focus on a specific pathogen or disease, making the clinician losing the big picture. IPC strategies proved their cost-effectiveness regardless typology, country, or pathogen. A standardized, universal, pragmatic protocol for HCW education should be elaborated. Likewise, a rapid outbreak recognition tool elaboration (i.e., an easy-to-use mathematical model) would improve early diagnosis and spreading prevention. Further studies are needed to express in favor or against MDROs decolonization. New promising strategies are emerging and need to be tested in the field. The lack of IPC strategies application has made, and still makes ICUs a major MDROs reservoir into the community. In a not-too-distant future genetic engineering and phage therapies could represent a plot-twist in MDROs IPC strategies.

The Mediterranean Diet, characterized by high intake of plant foods and unsaturated fats, has been suggested to improve assisted reproductive technology (ART) outcomes. This literature review aimed to summarize the evidence from observational studies on the associations between preconception Mediterranean Diet and ART outcomes. PubMed/MEDLINE, Embase, ScienceDirect, and Google Scholar databases were searched to identify relevant studies. Seven observational studies (n=2,321 women on ART) were included. Adherence to the Mediterranean Diet was assessed by food frequency questionnaires with 6-195 items. Three studies found that higher Mediterranean Diet scores improved Clinical Pregnancy or Live Birth rates, while two studies showed a positive effect on ART eggs and embryos. However, two studies reported no significant associations with ultimate ART success, and four studies found no effects on oocyte and embryo number or quality. Evidence for the effects of greater adherence to the Mediterranean Diet on ART outcomes is limited but promising. Additional rigorous research is needed to clarify and weigh the degree of association between the Mediterranean Diet and ART success.

Obesity is a highly prevalent chronic disease characterized by excessive weight gain and fat accumulation. There is growing evidence that Lactiplantibacillus plantarum strains with bile salt hydrolase (BSH) activity are effective in preventing and alleviating obesity. However, few of them has confirmed the anti-obesity effect of BSH by gene deletion. In this study, 23 BSH-positive Lp. plantarum strains were screened by bile salt precipitation halo assay. Among these strains, Lp. plantarum Lp20 showed the highest BSH activity with a hydrolysis rate to glycodeoxycholic acid (GDCA) by 91.62%. Genomic sequencing and bioinformatics analysis indicated that gene bsh1 was associated with BSH activity of Lp. plantarum Lp20 and gene deletion of bsh1 confirmed the role of Bsh1 in GDCA hydrolysis. To investigate if the Bsh1 from Lp. plantarum Lp20 could alleviate obesity, the wild type and bsh1 deletion mutant strains were administered daily for 8 weeks to diet-induced obese mice, respectively. Compared with mutant strain, the wild type strain Lp20 significantly reduced body weight gain, inguinal white adipose tissue and mesenteric fat mass in obese mice. In addition, Lp20 also reduced serum total cholesterol levels and LDL-C by 20.8% and 33.3%, respectively. Furthermore, the recovered liver steatosis was only observed in Lp. plantarum Lp20 treated mice. Taken together, the bile salt hydrolase Bsh1 from Lp. plantarum Lp20 was a key functional factor on ameliorating HFD-induced obesity by reducing cholesterol levels and suppressing adipogenesis in mice.

The aim was to identify if surface electromyography (sEMG) parameters are indicative of post-activation potentiation (PAP)/post-activation performance enhancement (PAPE), in terms of twitch potentiation and voluntary performance. Three databases were used in March 2024, with the following inclusion criteria: (a) original research, assessed in healthy human adults, (b) sEMG parameters were measured. The exclusion criteria were: (a) studies with no PAP/PAPE-protocol, (b) non-randomized control trials. The following data were extracted: study characteristics/demographics, PAP/PAPE-protocols, sEMG parameters, twitch/performance outcomes, and study findings. A modified physiotherapy evidence database (PEDro) scale was used for quality assessment. Fifteen randomized controlled trials (RCTs), with a total of 199 subjects were included. The M-wave amplitude (combined with a twitch torque outcome) was shown to generally be indicative of PAP. The sEMG amplitude (in some muscles) were found to be indicative of PAPE during ballistic movements, while a small decrease in the MdF (in certain muscles) were shown to reflect PAPE. Changes in the Hmax/Mmax ratio were found to contribute (temporally) to PAP, while the H-reflex amplitude was shown to be neither indicative of PAP nor PAPE. This review provides preliminarily findings suggesting that certain sEMG parameters could be indicative of PAP/PAPE. However, future research is warranted.

The literature study delves into novel therapeutic strategies in transplantation medicine, highlighting unique approaches that could revolutionize current practices. It emphasizes novel patterns that have the potential to transform the current landscape. Commencing with a thorough examination of the historical environment, it traces crucial advances and changes in transplantation. The focus is on traditional techniques, emphasizing their limitations and challenges. An extensive examination of contemporary transplantation therapies offers valuable insights into the most recent progress in organ, cellular, and tissue transplantation. This analysis examines the immunological obstacles and outlines the current advancements and constraints. The exploration further navigates into novel models and concepts such as immunomodulation, developments in organ preservation techniques, gene editing, biomaterials, scaffold-based solutions, and the integration of precision medicine, artificial intelligence, and machine learning applications. Each section analyzes the potential for change and current progress in various areas, backed by relevant scientific sources up to 2023. The subsequent sections delve into innovative cellular therapies, biotechnological progress, current clinical trials, and case studies demonstrating effective applications. This examination delves into the ethical and regulatory considerations of innovative therapeutic procedures, emphasizing ethical implications, regulatory frameworks, and the importance of balancing innovation with patient welfare. The literature review concludes by offering a forward-looking perspective, emphasizing potential progress, anticipated challenges, and advocating for collaboration and interdisciplinary approaches to overcome limitations in the field of transplantation medicine.

Salmonella infections can lead to intestinal inflammation and metabolic disorders in birds. However, whether ARA metabolism is involved in Salmonella-induced intestinal inflammation remains unclear. This experiment investigated the changes in cecal flora and arachidonic acid (ARA) metabolism in Hainan Wenchang chickens infected with S. Typhimurium using 16s rDNA sequencing and targeted metabolomics. The results showed that the levels of ARA metabolites were increased in the cecum tissue of Wenchang chickens after infection with S. Typhimurium, including prostaglandin E2, prostaglandin F2α, lipoxin A4, ±8(9)-EET, ±11(12)-EET, and ±8,9-DiHETrE. The content of key enzymes for ARA production and metabolism (PLA2 and COX-2) in chicken cecum tissues was increased after S. Typhimurium infection. The relative mRNA levels of inflammatory factors were also increased after infection, including IFN-γ, TGF-β1, IL-4, and IL-6. In HD11 cells, the use of a cyclooxygenase (COX) inhibitor reduced the increased levels of COX-2 and PGF2α induced by S. Typhimurium infection and effectively reduced the inflammatory response. In addition, the number of beneficial genera (e.g., Bifidobacterium, Lactobacillus, and Odorobacterium) in the cecum of Wenchang chickens was significantly reduced after infection with S. Typhimurium. In this study, we revealed the structure of the cecal flora of Wenchang chickens infected with S. Typhimurium and demonstrated that S. Typhimurium can mediate the onset and development of intestinal inflammation through the activation of the metabolic pathway of ARA cyclooxygenase in Wenchang chickens. The results can provide data support and theoretical support for the prevention and control of avian salmonellosis.

With the ongoing amendment of the EU legislation on the treatment of urban wastewater, stricter requirements for the removal of pollutants are expected, which calls for the need for innovative wastewater treatment technologies. Biological systems are still the first choice. The survey of typical bioreactors applied in wastewater treatment is presented. Wastewater treatment objective, bio-chemical environment and microbial growth are selected as a main criterion for classification of these bioreactors. Hydraulic and kinetic aspects are considered, advantages and drawbacks of these bioreactors regarding the selection of appropriate type of the reactor as well as regarding operation of reactors are mentioned. The aim of this paper is to provide operators and designers with a brief overview of selected traditional and advanced processes, reactors, and technologies for nutrient removal from municipal wastewater. Another goal is to discuss the possibilities and limitations to comply with more strict effluent standards. From the evaluation of the published papers, it follows that the currently applied traditional methods of nutrients removal have the potential to convey also with the expected stricter limits.

The goal of the study presented in this article is to investigate interconnection issues of the Intelligent Electrical Networks (IENs) with the existing ones, as well as the deployment of the appropriate load forecasting demand techniques. The concept of IENs has recently emerged as a potential solution to the global energy problem, due to the more flexible dispersed production units that are involved. In the same context, additional issues, such as the reduction of production-transfer-distribution costs as well as power losses are analyzed as well, via the penetration of Renewable Energy Sources (RESs). To this end, it is necessary to use appropriate advanced infrastructure, where in combination with modern telecommunication networks will make possible the full exploitation of IENs. Moreover, to make the electricity system more efficient, to avoid voltage and frequency imbalance issues and to implement optimal production and consumption planning, the Electric Load Forecast (ELF) is a vital process and plays a key role in the planning as well as in the management of electricity systems. Therefore, recent state of the art approaches in ELF methods are discussed as well.

Pyrethroid pesticides (PYRs) as the third most widely used pesticides, following organophosphorus and carbamate pesticides, which are of significant importance in the analysis and detection of vegetables. However, the current pretreatment technology for PYRs confronts challenges of difficult separation and low enrichment efficiency, resulting in a cumbersome and time-consuming pretreatment process with poor selectivity. Here, a simple and efficient magnetic solid-phase extraction (MSPE) strategy was developed to simultaneously purify and enrich five PYRs in vegetables, with the magnetic covalent organic framework nanomaterial COF-SiO2@Fe3O4 as an adsorbent. The COF-SiO2@Fe3O4 was prepared by a simple solvothermal conditions method, using Fe3O4 as magnetic core, benzidine and 3,3,5,5-tetraaldehyde biphenyl as two building units. COF-SiO2@Fe3O4 could effectively capture the targeted PYRs by virtue of its abundant π-electron system and hydroxyl groups. The impact of various experimental parameters on extraction efficiency was investigated to optimize the MSPE conditions, including adsorbent amount, extraction time, elution solvent type and elution time. Subsequently, method validation was conducted under the optimal conditions in conjunction with gas chromatography-mass spectrometry (GC-MS). Within the range of 5.00–100 μg·kg-1 (1.00–100 μg·kg-1 for bifenthrin and 2.5–100 μg·kg-1 for fenpropathrin), the five PYRs exhibited a strong linear relationship, with determination coefficients ranging from 0.9990 to 0.9997. The limits of detection (LODs) were 0.3–1.5 μg·kg-1, and the limits of quantification (LOQs) were 0.9–4.5 μg·kg-1. The recoveries were 80.2–116.7% with relative standard deviations (RSDs) below 7.0%. Finally, COF-SiO2@Fe3O4, NH2-SiO2@Fe3O4 and Fe3O4 were compared as MSPE adsorbents for PYRs. The results indicated that COF-SiO2@Fe3O4 was an efficient and rapid selective adsorbent for PYRs. This method holds promising prospects for the determination of PYRs in real samples.

High hopes were associated with the new anti-angiogenic medicament, bevacizumab, which due to the possibility of binding to isoform A of vascular endothelial growth factor (VEGF), inhibited the creation of new blood vessels. However, not only blood vessels are responsible for the tumor cells' spread. During the process of tumor growth, lymphangiogenesis is mediated by other isoforms of the VEGF family, specifically VEGF-C and VEGF-D, which are independent of the bevacizumab action. Therefore, based on the mechanism of bevacizumab action and the processes of angio- and lymphangiogenesis, we formed three hypotheses: 1) if the lymph nodes in the primary ovarian cancers are metastatic, the outcome of bevacizumab treatment is worsened; 2) concerning the second-line treatment, bevacizumab will act in a weakened manner if the recurrence occurs in lymph nodes compared to local recurrences; 3) patients treated by bevacizumab are more likely to have recurrences in lymph nodes. These hypotheses raise the issue of the existing gap of knowledge, which concerns the effect of bevacizumab on the metastatic lymph nodes.

Global coverage and scale up of interventions to reduce newborn mortality remains low, though progress has been achieved in improving newborn survival in many low-income settings. An important factor in the success of newborn health interventions, and moving to scale, is appropriate design of community-based programs and strategies for local implementation. We report the results of formative research undertaken to inform the design of a newborn health intervention in Cambodia. Information was gathered on newborn care practices over a period of three months using multiple qualitative methods of data collection in the primary health facility and home setting. Analysis of the data indicated important gaps, both at home and facility level, between recommended newborn care practices and those typical in the study area. The results of this formative research have informed strategies for behavior change and improving referral of sick infants in the subsequent implementation study. Collection and dissemination of data on newborn care practices from settings such as these can contribute to efforts to advance survival, growth and development of newborns for intervention research, and for future newborn health programming.

The objective of this study was to investigate the concentration and spatial distribution patterns of six potentially toxic heavy metal elements (Mn, Zn, Cr, Pb, Cu and Ni) in bus station dusts in the Xifeng district of Gansu province, NW China. The contents were analyzed for Mn, Zn, Cr, Pb, Cu and Ni by using S8 TIGER Brochures wavelength dispersive X-ray fluorescence spectrometry. Geoaccumulation index (Igeo ), enrichment factor (EF), pollution index (PI) and integrated pollution index(IPI) were calculated to evaluate the heavy metal contamination level of bus station dusts. The results indicate that, in comparison with the background values of local soil, bus station dusts in Xifeng have elevated metal concentrations as a whole. The concentrations of heavy metals investigated in this paper are compared with the reported data of other cities. The results show that the arithmetic means of Mn, Zn, Cr, Pb, Cu and Ni are 440.8, 137.9, 60.0, 42.8, 33.5 and 19.8mg kg−1 respectively. The mean values of Igeo reveal the order of Ni<Mn<Cr<Cu<Zn<Pb. The high Igeo and EF for Cu, Zn and Pb in bus station dusts indicate that there is a considerable Cu, Zn and Pb pollution, which mainly originate from traffic and industry activities. The Igeo and EF of Ni, Mn and Cr are low and the assessment results indicate an absence of distinct Ni, Mn and Cr pollution in bus station dusts. The assessment results of PI also support Cu, Zn and Pb in bus station dusts presented middle pollution, and IPI indicates heavy metals of bus station dusts polluted seriously.

The layer-by-layer (LBL) fabrication method allows for controlled microstructure morphology and vertical component distribution, and also offers a reproducible and efficient technique for fabricating large-scale organic solar cells (OSCs). In this study, polymer D18 and PYIT-OD are employed to fabricate all-polymer solar cells (all-PSCs) using the LBL method. Morphological studies reveal that the use of additives optimizes the microstructure of the active layer, enhancing the crystallinity and charge transport capability. The optimized device with 2% CN additive significantly reduces bimolecular recombination and trap-assisted recombination. All-PSCs fabricated by the LBL method based on D18/PYIT-OD deliver a power conversion efficiency (PCE) of 15.07%. Our study demonstrates the great potential of additive engineering via LBL fabrication method in regulating microstructure of active layers, suppressing charge recombination, and enhancing the photovoltaic performance of devices.

The general synthesis of boron-containing cyclic compounds (boracycles) necessitates toxic organotin precursors or highly reactive boron halides. Here we report the synthesis of seven- and five-membered boracycles utilizing arylboronic acid pinacol esters (ArBpins) as stable boron sources. Grignard reagents generated from 2,2′-dibromodibenzyl or 2,2′-dibromobiphenyl reacted with ArBpins, where Ar = 9-anthryl (Anth), 2,4,6-trimethylphenyl (Mes), 2,4,6-triisopropylphenyl (Tip), to give 10,11-dihydro-5H-dibenzo[b,f]borepins or dibenzoborole derivatives. This Bpin-based method was successfully applied to a one-shot double boracycle formation, providing a dihydrodibenzoborepin–anthracene–dihydrodibenzoborepin triad molecule in a good yield. The dihydrodibenzoborepin bearing the Anth group was directly converted to the unsaturated borepin by NBS/AIBN. All products were characterized by NMR, HRMS, and in some cases, single-crystal X-ray diffraction analysis. Additionally, the photophysical properties of the products are also reported.

Fabrication of durable materials with excellent oil adsorption capacity and separation performance for the treatment of oily wastewater is meaningful based on smart responsiveness. Herein, a solvent-responsive melamine sponge (MS) was developed via silanization followed by the in-situ growth of zeolitic imidazolate framework-8 (ZIF-8). Detailed characterization of the resultant composite MS was conducted using scanning electron microscopy (SEM), energy dispersive spectrometer (EDS), X-ray diffraction (XRD), and Fourier transform infrared spectroscopy (FTIR). The multiscale hierarchical MS substrate exhibited highly hydrophobic property in the pH range of 1-11, along with a satisfactory adsorption capacity in the range of 65.4-134.2 g/g for different oils. The modified surface transformed from superhydrophobicity/superlipophilicity to superhydrophilicity/underwater superoleophobicity upon ethanol wetting, reverting to its original superhydrophobic state upon drying. The separation flux of the MS substrate was above 1.5×104L/m2h for both oil and water removal, along with the separation efficiency more than 98.7%. No obvious changes of the separation performance after 50 successive immiscible oil/water separation indicated the excellent durability and robustness of the anchored ZIF-8 nanoparticles on the surface of modified MS substrate. More importantly, oil-in-water emulsion separation was successfully carried out via the ZIF-8 MS composite with a high separation efficiency over 99.1%. The developed smart sponge with high oil absorption capacity, excellent chemical stability and fire resistance exhibited a wide range of potential practical applications in the convenient treatment of oily wastewater.

The existing methods of oil palm Fresh Fruit Bunch (FFB) evacuation from in-field to temporary collection point which typically apply medium to large tractors, often result in unexpected soil compaction. Meanwhile, smaller size equipment indicates low working capacity and unable to perform direct unloading to collection bin. This paper addresses the challenge of FFB evacuation by focusing on preventing soil compaction, increasing working capacity and enabling direct unloading to collection bin. For this purpose, a 6x6WD transporter prototype with a scissor lift mechanism was developed. With the design, the transporter could evacuate FFB in both steep mineral terrain and low ground pressure peatland, able to carry FFB with capacity of 750 kg and provide direct unloading into collection bin. The average field working capacity of the transporter was found to be 15 tons day-1. This research offers insights for future designs of medium-sized FFB transporters with advanced unloading mechanisms.

In this systematic review, the PRISMA method was applied to examine publications from the last two decades that have investigated the noxious gaseous emissions from dairy barns. The aim was to analyse the outcomes from literature studies estimating the quantities of polluting gases produced in dairy barns, with specific focus on ammonia (NH₃) emissions. The review also explores proposed methods to reduce the associated effects through mitigation strategies. Estimation of NH₃ emissions is significantly influenced by the complex interactions among several factors, including animal management practices, such as controlling animal behavioral activities; manure management, like utilising practices for floor manure removal; the type of structure housing the animals, whether it is naturally or mechanically ventilated; and environmental conditions, such as the effects of temperature, wind speed, relative humidity, and ventilation rate on NH₃ release in the barn. These influential components have been considered by researchers, identifying targeted mitigation strategies. Despite growing attention to the issue, gaps in the scientific literature were identified and discussed, particularly regarding the analysis of mitigation strategies and their long-term impacts (i.e., environmental, economic and productivity-wise).

Lactoperoxidase (LP) is an important enzyme of the salivary and mammary glands. It has been proven to increase the shelf life of raw milk by inhibiting the growth of bacteria, especially Listeria monocytogenes, Escherichia coli, Staphylococcus aureus, and Pseudomonas spp. The aim of this work was to verify the use of LP to extend the shelf life of meat products. In vitro experiments showed inhibitory effects against selected bacteria (Listeria innocua (ATCC 33090), Staphylococcus saprophyticus (CP054440.1), and Pseudomonas fluorescens (ATCC 13525) due to prolongation of the lag phase of growth curves. A lower increase in viable counts (P &lt; 0.05) was also found by testing the pork cubes surface treated with LP solution (5%) + L. innocua and stored for 7 days at 15 °C. LP has also been studied at concentrations of 0.25 and 0.50% in meat products (pork ham and pâté) during refrigerated storage (4 °C for 28 days). Lower viable counts were observed throughout the storage experiment, especially for 0.50% LP (P &lt; 0.05). Meat products containing LP also showed lower levels of oxidation (MAD) (P &lt; 0.05). According to these results, LP could extend the shelf life of a wider range of products.

Это исследование сосредоточено на разработке системы искусственного зрения для гибкого дельта-робота-манипулятора и ее интеграции с межмашинной связью для оптимизации взаимодействия устройств в реальном времени. Эта интеграция направлена ​​на увеличение скорости роботизированной системы и улучшение ее общей производительности. Предлагаемое сочетание системы искусственного зрения с межмашинной связью позволяет обнаруживать и распознавать цели с высокой точностью в режиме реального времени в ограниченном пространстве, предназначенном для позиционирования, дальнейшей локализации и выполнения производственных процессов, таких как сборка или сортировка деталей. . В данном исследовании RGB-изображения используются в качестве входных данных для алгоритма MASK-R-CNN, а результаты обрабатываются в соответствии с особенностями прототипа дельта-манипулятора робота. Данные, полученные от MASK-R-CNN, адаптированы для использования в системе управления дельта-роботом с учетом ее уникальных характеристик и требований к позиционированию. Технология M2M позволяет манипулятору робота быстро реагировать на изменения, например, на перемещение объектов или изменение их положения, что имеет решающее значение для задач сортировки и упаковки. Система была протестирована в условиях, близких к реальным, чтобы оценить ее производительность и надежность.

Psoriasis is a chronic recurrent inflammatory autoimmune pathology, with a major genetic component and several interferences of immunological cells and their cytokines. The complex orchestration of psoriasis pathogenesis is related to the synergic effect of immune cells, polygenic alterations, the presence of autoantigens and several external factors. The major act of IL-23/IL-17 axis, strongly influencing the inflammatory pattern established during the disease activity, is visible as a continuous perpetuation of the pro-inflammatory response and keratinocyte activation and proliferation leading to the development of psoriatic lesions. Genome wide association studies (GWAS) along offered a better view of psoriasis pathogenic pathways, with approximately one third of psoriasis genetic impact on psoriasis development is associated to MHC region, with genetic loci located on chromosome 6. The most eloquent genetic factor of psoriasis, PSORS1, was identified in the MHC I site. Between the several factors involved in its complex etiology, dysbiosis, due to genetic or external stimulus, exhibiting less variety and the involvement of pathogenic bacteria, cand induce a burst of proinflammatory consequences, both cutaneous and gut microbiome being involved in psoriasis pathogenic process. A complex understanding of the major pathways that interplay in order to initiate and perpetuate psoriatic diseases and its associated comorbidities can help the current clinical practice by properly evaluating completely and individualized each patient and establish the proper therapeutic management.

Background: The practice of self-medication is common worldwide and is an important component of medical self-care. However, the practice can be dangerous and is linked to various risks for the patients and the entire community. This study aimed to estimate the prevalence and factors associated with self-medication among Bangladeshi adults. Methods: A cross-sectional survey was conducted between April and June 2021 among Bangladeshi adults (aged &gt;19 years) using convenient sampling. A total of 1320 data were collected through face-to-face interviews using a standardized questionnaire. Multivariable logistic regression analysis was used to identify factors associated with self-medication practice (SMP). Results: Overall, 41% of adults in our survey reported SMP. The most common illnesses that prompted SMP were common cold/flu (66.4%), gastric problems (65%), and headache (64.4%). The most frequent reasons for SMP were to get better services (30.59%), perceive SMP without side effects (23.28%), and save time with effectiveness (14.56%). Potential risk factors included 10 years (AOR = 1.91; 95% CI: 1.04 - 3.50) and &gt;12 years of schooling (AOR = 5.03; 95% CI: 2.27 - 11.15), being a businessman (AOR = 4.64; 95% CI: 1.74 - 12.37), having ≤6 family members (AOR = 2.13; 95% CI: 1.40 - 3.24), being a member of a social group (AOR = 1.53; 95% CI: 1.10 - 2.12), a health status check after every six months (AOR = 1.52; 95% CI: 1.08 - 2.13), and current ill-health (AOR = 1.41; 95% CI: 1.06 - 1.87). Protective factors identified included ≤30 years of age (AOR = 0.40; 95% CI: 0.17 - 0.93), and practice of modern (AOR = 0.39; 95% CI: 0.22- 0.69) and herbal (AOR = 0.45; 95% CI: 0.21- 0.97) healing types. Conclusion: More than one-third of the study participants reported practicing self-medication. Increasing the community’s awareness of the extreme consequences of SMP and not just the average experience might sway individuals away from SMP, and implementing strict jurisdiction could be a way to minimize the SMP.

The purpose of the study is to establish compliance of the design of the modernized car with the requirements for safe operation. An option has been proposed for upgrading a passenger wagon to a Mobile Diagnostic Complex for transporting a combined vehicle equipped with appropriate flaw detection equipment intended for rail diagnostics. The authors have established the most optimal option for locating the diagnostic vehicle on board the Mobile Diagnostic Complex (MDC) wagon, taking into account the additional load from the vehicle. To achieve this goal, the article developed a three-dimensional model of the supporting structure of the wagon body, proposed a methodology and presented the results of a study of the stress-strain state of the wagon body, taking into account the additional weight of the wagon. The article develops a methodology for studying the natural frequencies of vibrations of the wagon body and develops a three-dimensional model of the wagon for calculating dynamic indicators in the Universal Mechanism software package. Taking into account the previously carried out strength calculations, as well as in order to maintain the factory life cycle indicators of the supporting structure of the wagon body, it is recommended to use the model in the first version.

The objective of this work was to evaluate the roast time, weight loss and quality of coffee grain at four different roasting degrees, aiming to recognize and develop sustainable patterns to industrialize specialty coffees. Coffee (Coffea arabica L.), from eight producers, with scores between 80 and 83 from SCA classification, were used. Samples of 300 g were roasted in a cylindric rotative roaster, until the grains reached four different roasting profiles (Agtron scale 22.36, #33.64, #40.05, #59.92). Afterwards, analysis of roasting time, gas pressure, weight loss, and sensorial grades were accomplished. It was observed that samples roasted at #22.36 led to significant differences, regarding roasting time and weight loss. Furthermore, there is a significant difference at the sensorial grades of the coffee beverage. Comparing the roast degree #40.05 (standard used for specialty coffee) with the roast degree #22.36 (most used for commodities coffee), the first one has a gas consumption of 0.34 kg per coffee kg, whilst the second presented a gas consumption of 0.41 kg per coffee kg. Thus, from gas consumption, roast degree # 40.05 is the more sustainable option, along with the remaining parameters analyzed.

We report neutralization titer data against contemporary SARS-CoV-2 sublineages from an ongoing, open-label, phase 2/3 trial of a single 30-μg dose of monovalent Omicron XBB.1.5-adapted BNT162b2 vaccine. Healthy participants had previously received ≥3 doses of a US-authorized mRNA vaccine, with the most recent being a bivalent Omicron BA.4/BA.5-adapted vaccine administered ≥150 days before study vaccination. In this analysis, Omicron XBB.1.5, BA.2.86, and JN.1 serum neutralizing titers were assessed at baseline and 1 month after vaccination in a subset of ≥18-year-olds (N = 40) with evidence of previous SARS-CoV-2 infection. Immunogenicity was also evaluated in a demographically matched group of participants who received bivalent BA.4/BA.5-adapted BNT162b2 in another study (ClinicalTrials.gov Identifier: NCT05472038). The XBB.1.5-adapted BNT162b2 vaccine elicited higher XBB.1.5, BA.2.86, and JN.1 neutralizing titers than those elicited by bivalent BA.4/BA.5-adapted BNT162b2. Overall geometric mean fold rises in neutralizing titers from baseline to 1 month after vaccination were higher among participants who received XBB.1.5-adapted BNT162b2 than those who received bivalent BA.4/BA.5-adapted BNT162b2 for XBB.1.5 (7.6 vs 5.6), slightly higher for JN.1 (3.9 vs 3.5), and similar for BA.2.86 (4.8 vs 4.9). ClinicalTrials.gov Identifier: NCT05997290.

Introduction Blunt carotid injuries (BCI) in pediatric trauma are quite rare. Due to the low number of cases, only a few reports and studies have been conducted on this topic. This review will discuss how frequent BCI/ BCVI on pediatric patients after blunt trauma is, what routine diagnostics look like, if a CT/ CTA scan on pediatric patients after blunt trauma is always necessary and if there are any negative health effects? Methods This literature review includes reviews, systematic reviews, case reports and original studies in english language between 1999 and 2020 that have dealt with pediatric blunt trauma and the diagnostics of BCI and BCVI. Furthermore, publications on the risk of radiation exposure on children were included in the study. For literature research, Medline (PubMed) and the Cochrane library were used. Results Pediatric BCI/ BCVI, shows an overall incidence between 0.03 – 0.5% of confirmed BCI/ BCVI cases due to pediatric blunt trauma. 1.1 – 3.5% of pediatric blunt trauma patients underwent CTA to detect BCI. Only 0.17 – 1.2% of all CTA scans shows a positive diagnosis for BCI. In children, the median volume CT dose index on a non-contrast head CT is 33 milligray, a computed tomography angiography needs at least 138 mGy. A cumulative doses of about 50 mGy almost triples the risk of leukemia, and doses of about 60 mGy triples the risk of brain cancer. Discussion Knowing that a BCI could have extensive neurologic consequences for children, it is necessary to evaluate routine pediatric diagnostics after blunt trauma. Computed tomography scans (CT) and computed tomography angiography (CTA) are mostly used in routine BCI diagnostics. However, since radiation exposure in children should be as low as reasonably achievable, it should be asked if other diagnostic methods could be used to identify risk groups. Trauma guidelines and clinical scores like the McGovern score are reflect established BCI screening options, as well as using duplex ultrasound.

Daily maximum surface air temperature (Tamax) is a crucial factor for understanding complex land surface processes under rapid climate change. Remote detection of Tamax has widely relied on the empirical relationship between air temperature and land surface temperature (LST), a product derived from remote sensing. However, little is known about how such a relationship is affected by the high heterogeneity in landscapes and dynamics in seasonality. This study aims to advance our understanding of the roles of land cover and seasonal variation in the estimation of Tamax using the MODIS (Moderate Resolution Imaging Spectroradiometer) LST product. We developed statistical models to link Tamax and LST in the middle and lower reaches of the Yangtze River in China for five major land-cover types (i.e., forest, shrub, water, impervious surface, cropland, and grassland) and two seasons (i.e., growing season and non-growing season). Results show that the performance of modeling the Tamax-LST relationship was highly dependent on land cover and seasonal variation. Estimating Tamax over grasslands and water bodies achieved superior performance; while uncertainties were high over forested lands that contained extensive heterogeneity in species types, plant structure, and topography. We further found that all the land-cover specific models developed for the plant non-growing season outperformed the corresponding models developed for the growing season. Discrepancies in model performance mainly occurred in the vegetated areas (forest, cropland, and shrub), suggesting an important role of plant phenology in defining the statistical relationship between Tamax and LST. For impervious surfaces, the challenge of capturing the high spatial heterogeneity in urban settings using the low-resolution MODIS data made Tamax estimation a difficult task, which was especially true in the growing season.

The synchronization of complex networks is believed to be closely related to network topology. How to study synchronization of real network without clear topology and parameters? In this Letter, a synchronized stability boundary equation is derived that is system- and disturbance-independent and applicable to arbitrarily coupled grids. The results imply that spontaneous synchronization in a network may be network independent. These conclusions provide new research paths for network synchronization and analyze the synchronization stability of grids in a unified way.

We discuss three key points: defining mathematically the notions of phase, symmetry breaking, topological defects and their stability in a formal language of homotopy theory and fiber bundle formalism; postulating and proving two theorems for successive symmetry breaking scenarios in condensed matter physics and cosmology, and demonstrating application of theorems to superfluid Helium 3 and Kibble-Lazarides-Shafi (KLS) walls, supporting and mathematically justifying the results of [Volovik, 2020].

An especially important species in southern Brazil, yerba mate (Ilex paraguariensis) is traditionally consumed as tea, chimarrão and tererê. Yerba mate consumption has been stimulated by scientific discoveries that have identified high concentrations of bioactive compounds and their health benefits. There are no studies or scientific evidence to certify or guarantee stability of these compounds’ concentrations during different years in the same plants. We were interested in quantifying caffeine, theobromine, total phenolic compounds and proteins concentrations in leaves of yerba mate genotypes and their stability in the same plants over four consecutive years. Mature leaves from yerba mate genotypes selected on a provenance and progenies trial were collected in August of 2015, 2016, 2017 and 2018. Methylxanthines (caffeine and theobromine), total phenolic compounds and total protein contents were quantified. Our results indicate large variations between genotypes regarding caffeine (0.035 to 2.385 g 100 g^-1), theobromine (0.0004 to 1.772 g 100 g^-1), total phenolic compounds (7.028 to 9.424 g 100 g^-1) and proteins (10.39 to 16.58 g 100 g^-1) contents, and also high stability of those compounds over the four evaluated years. A great variation of the studied bioactive compounds in different Ilex paraguariensis genotypes was found and its stability over four consecutive years was showed.

Berberine (BER) is a natural alkaloid found in various Berberis species, used traditionally in herbal medicine and dietary supplements. BER exhibited various biological activities, including anti-inflammatory, antioxidant, antidiabetic, and anti-tumour properties by modulating cellular pathways and influencing gene expression. While BER shows promise in various health applications, its possible toxicity raises concerns. In 2023, EFSA issued a call for data on BER- and protoberberine (PROTBER)-containing products, to comprehensively assess its safety and potential health claims. With these premises, new data was collected by assessing: i) the phytochemical profile of BER- and PROTBER-containing preparations by newly developed HPLC-DAD method; ii) in silico and in vitro investigation of pharmacokinetics properties of BER; iii) in vitro cytotoxicity in different human cell lines and, iv) biological and molecular activities of extracts containing BER and PROTBER in in vitro human non-cancer cells. By testing 16 commercial Berberis extracts, the evidence collected showed a good qualitative reliability in terms of phytochemical profile and limited relapses on cytotoxicity even at 200 µg/ml after a 24h of exposure, while evidencing a good cellular bioavailability and cell migration inhibition. The potential for plant-drug interactions affecting CYP450 proved to be minimal. Overall, our work provides a useful overview to better elucidate potential concerns on botanicals containing BER and minor PROTBER commonly used in food supplement.

Fungi are rich sources of secondary metabolites of agrochemical, pharmaceutical and food importances, such as mycotoxins, antibiotics and antitumor agents. Secondary metabolites play vital roles in fungal pathogenesis, growth and development, oxidative status modulation, and adaptation/resistance to various environmental stresses. LaeA contains an S-adenosylmethionine binding site and displays methyltransferase activity. The members of velvet proteins include VeA, VelB, VelC, VelD and VosA, for each member with a velvet domain. LaeA and velvet proteins can form multimeric complexes such as VosA-VelB and VelB-VeA-LaeA. They belong to global regulators and are mainly impacted by light. One of their most important functions is to regulate gene expression that are responsible for secondary metabolite biosynthesis. The aim of this mini-review is to represent the newest cognition on the biosynthetic regulation of mycotoxins and other fungal secondary metabolites by LaeA and velvet proteins. In most cases, LaeA and velvet proteins positively regulated production of fungal secondary metabolites. The regulated fungal species mainly belong to the toxigenic fungi from the genera of Alternaria, Aspergillus, Botrytis, Fusarium, Magnaporthe, Monascus, and Penicillium for the production of mycotoxins. We can control secondary metabolite production to inhibit the production of harmful mycotoxins while promoting the production of useful metabolites by global regulation of LaeA and velvet proteins in fungi. Furthermore, the regulation by LaeA and velvet proteins should be a practical strategy in activating silent biosynthetic gene clusters (BGCs) in fungi to obtain previously undiscovered metabolites.

Diabetes mellitus is one of the most common endocrinopathies, estimated to affect about 5.4% of the world's population around 2025. It is thought that nearly a third of diabetic patients have some type of skin condition. Frequently, the cutaneous effects of this heterogeneous syndrome are ac-curately detected late in the progressive form of the disease. The main objective of the present study was to identify the main cellular characteristics of the cutaneous microenvironment in exper- imentally induced diabetes mellitus. Skin fragments were harvested from adult white Wistar rats of both sexes, with the weight of 200 g, 12 weeks after streptozotocin diabetes was induced. In parallel with histopathological diagnosis by using hematoxylin and eosine staining, samples were processed by transmission electron microscopy technique and examined with a Philips CM100 microscope. In the apparently macroscopically unchanged tegument, photon microscopy revealed both progres ive thinning of the epidermis in the early stages of diabetes and a significant process of fibrosis and collagen hyalinization in the dermis. In addition, in the early stages, the electron microscopic study provided ultrastructural details characteristic of a senescent phenotype with reduced cell proliferation. The morphological changes in the skin may be the first signs of disruption of carbohydrate metabolism and in the case of established diabetes may reflect its progression and the efficacy of therapy.

Oligopeptide transporters (OPTs) are a group of membrane localized proteins that have a broad range of substrate transport capabilities and contribute to numerous biological processes. However, limited information has been reported on OPTs in higher plants. In this study, a comprehensive analysis of the OPT gene family in Medicago truncatula was performed. A total of 26 OPT genes (MtOPT01-MtOPT26) have been identified in the Medicago truncatula genome. Phylogenetic analyses indicated that MtOPTs consisted of two distinct subgroups, 12 MtOPTs belonged to the peptide transport subgroup (PT-OPT) based on their predicted amino acid sequences containing the two highly conserved motifs (NPG and KIPPR) and 14 MtOPTs belonged to yellow stripe subgroup (YS-OPT). The MtOPTs distributed on each of 8 chromosomes in Medicago truncatula. Sequence analysis verified that MtOPTs significant similar to those in other plants. The copy number of MtOPTs was low and the multiply of MtOPTs was simple relatively. Gene structure analysis showed that most of the MtOPTs have various numbers of introns. The multiple of MtOPTs might play different biological roles which were supported by the fact that MtOPTs have a distinct tissue-specific expression pattern. The data obtained in this study will help to better understand the complexity of the MtOPTs gene family and provide new evidence for the function and evolution of the OPT gene family in higher plants.

This paper examines the use of multisensory virtual reality (VR) as a novel approach in psychological therapy for autobiographical memory retrieval with benefits for cognitive enhancement, stress reduction etc. The research in this paper was done under Romanian Arut Research Grant no. 27/09/10/2023 ”Intelligent VR system for treating autobiographical/episodic memory deficits".  By simulating realistic multisensory experiences, VR technology offers an immersive environment that surpasses traditional therapeutic methods in effectiveness. Previous studies demonstrate improved outcomes in treating various psychological conditions (affective disorders and PTSD, specific phobias and age-related cognitive decline). Technological advancements in VR, such as olfactory integration cand contribute to the realism and therapeutic potential of these environments, the integration of various physical stimuli with VR holds promising potential psychological therapies and highlighting the need for further interdisciplinary research. In this pilot study we tested the efficacy of a new system for triggering autobiographical memory retrieval. For this we used images combined with odors in a congruent manner and offering participants the chance to interact with the VR environment by using 2 virtual hands. We evaluated the efficacy of this system using qualitative methods with emphasis on the evaluation of the emotions associated with memory recollection and the ease of triggering memories. All participants in our pilot study experienced intense emotions related to childhood or adolescence and the pleasant feelings they had during the experiment persisted even after it ended. This is an advancement to what exists currently and original research elements for our paper.

Simple Summary: This review explores the origin of Leukemic Stem-Like Cells (LSLCs) from (Very) Small Leukemic Stem-Like Cells ((V)SLSLCs) and Cancer Stem Cells (CSCs) from trans-formed Very Small Embryonic-Like Stem Cells (VSELSCs). Understanding this relation is a step toward uncovering the mechanisms behind cancer and leukemia initiation and development. We explore how these very small precursor cell stages might contribute to the initiation and progres-sion of cancer as well as leukemia with a focus on Acute Myeloid Leukemia (AML) as a model. Abstract: Recent experimental findings indicate that CSCs originate from transformed VSELSCs, which are early precursor stages of healthy stem cells. This discovery marks a crucial step in understanding the mechanisms that drive cancer development and initiation. Our team's follow-up studies on leukemia, lung cancer, and healthy embryonic kidney cells have, for the first time, identified stag-es resembling very small precursor stem cells in continuously growing cell lines. These findings suggest the existence of (Very) Small Cancer Stem Cells ((V)SCSCs) or (V)SLSCs within respective subpopulations of CSCs and LSCs in vivo. In this review, we explore theoretical examples of how leukemia progresses through various stages, highlighting the role of these very small precursor cells as fundament primitive stages. We also discuss the potential implications of further research into these unique cellular stages for advancing cancer and leukemia treatment and prevention strategies.

With the exponential growth of internet usage and mobile devices, the volume of user behavior data has surged, offering significant opportunities and challenges for businesses. This paper explores user behavior analysis in the context of big data, highlighting its pivotal role in driving innovation and strategic decision-making. We begin by discussing the importance of user behavior data and reviewing technological advancements such as machine learning, natural language processing, and data mining that enable deep insights into user behavior. Through a case study on linguistic analysis in livestreaming e-commerce, we demonstrate how text-mining techniques can correlate linguistic characteristics with sales performance, providing actionable marketing insights. We further explore the broader business applications, including personalized recommendations, user portraits, product design, and strategic decision-making. Technical and ethical challenges, such as data integration, privacy concerns, and algorithmic bias, are also addressed. The paper concludes with a discussion on future trends, such as AI and ML advancements, edge computing, IoT proliferation, and ethical AI frameworks, poised to shape user behavior analysis. Our findings underscore the transformative potential of user behavior data in enhancing business operations and user experiences, providing recommendations for future research focused on real-time analytics, privacy-preserving techniques, and ethical implications of data-driven decisions.

The fast decoding of low-density parity-check (LDPC) is crucial for its future applications. In this paper, we propose to use Early Termination (ET) and Force Convergence (FC) techniques to accelerate the decoding of two new local/global two-phases decoding algorithms to reduce the Globally Coupled (GC) LDPC codes. Specifically, ET is applied in the local decoding phase of two- phases decoding of GC-LDPC codes to skip the local decoding which is highly likely to fail and avoid the unnecessary iterations. FC is applied in global decoding phase where converged variable nodes are identified and removed from Tanner graph and the decoding can be speed up shrinking parity check matrices. Two variants are proposed for the ET operation in local decoding phase. ET-1 merely stops iteration if it meets the stopping criterion while in ET-1, the iteration number saved in local decoding is added up in global decoding to improve the decoding performance. The simulation results show that the ET-1-FC scheme can save up to 42% decoding time complexity in the low SNR region while keeping the error rate performance nearly unchanged, the ET-2-FC can improve the error rate performance by 0.18dB at bit error rate 0.001 or 0.23dB at frame error rate 0.1. In the waterfalling region of BER/FER curves, both schemes can save about 25% decoding time complexity.

Esterquats constitute a unique group of quaternary ammonium salts (QASs) that contain an ester bond in the structure of the cation. Despite the numerous advantages of this class of compounds, only two mini-reviews discuss the subject of esterquats: the first one (2007) briefly summarizes their types, synthesis, and structural elements required for a beneficial environmental profile and only briefly covers their applications whereas the second one only reviews the stability of selected betaine-type esterquats in aqueous solutions. The rationale for writing this review is to critically reevaluate the relevant literature and provide others with a “state-of-the-art” snapshot of choline-type esterquats and betaine-type esterquats. Hence, the first part of this survey thoroughly summarizes the most important scientific reports demonstrating effective synthesis routes leading to the formation of both types of esterquats. In the second section, the susceptibility of esterquats to hydrolysis is explained, and the influence of various factors, such as the pH, the degree of salinity or the temperature of the solution, was subjected to thorough analysis that includes quantitative components. The next two sections refer to various aspects associated with the ecotoxicity of esterquats. Consequently, their biodegradation and toxic effects on microorganisms are extensively analyzed as crucial factors that can affect their commercialization. Then, the reported applications of esterquats are briefly discussed, including functionalization of macromolecules, such as cotton fabric as well as their successful utilization on a commercial scale. The last section demonstrates the most essential conclusions and reported drawbacks that allow us to elucidate future recommendations regarding the development of these promising chemicals.

In order to tackle the issue of severe rocking phenomenon under seismic conditions in structures equipped with steel spring isolation bearings, this paper investigates a novel type of anti-rocking bearing. Firstly, the structural configuration and working principle of the novel anti-rocking bearing are introduced, and a design method for bearing parameters is proposed. Secondly, a finite element analysis model is established using SAP2000 software to conduct nonlinear dynamic time history analysis under seismic loading. The analysis results show that the structural arrangement of the novel anti-rocking bearing reduces both the vertical displacement difference and the rocking angle of the isolation layer. The bearing exhibits a certain level of anti-rocking effect, but it may cause significant tensile forces in some bearings, necessitating the installation of anti-tensile reinforcement. The effectiveness of the anti-rocking effect improves as the stiffness of the steel tension rod in the bearing increases; however, it also leads to higher maximum tension in individual bearings as well as the total tension in all bearings. For structures equipped with the novel anti-rocking bearing, the acceleration amplifies under most cases, with amplification coefficients ranging from 0.82 to 1.55. The performance of the novel anti-rocking bearing varies significantly for different seismic waves. The stiffness of the steel tension rod should be determined considering the reference pressure of the bearing and the maximum designed tension of the bearing. Through the finite element simulation of the bearing, the mechanical properties of the bearing are basically the same as the theoretical analysis results. For the cylinder and the joint bearing, certain structural measures need to be taken to ensure its strength and stiffness.

The accompanying mechanical behavior during the flow of ore-rock dispersion is an important factor leading to the instability and failure of the orepass in the ore storage section. It is of great significance to accurately understand the instability characteristics of the well wall in the ore section, during the ore drawing process by understanding the flow characteristics and internal mechanical transfer mechanism of ore-rock dispersion. Using the discrete element method to analyze the flow characteristics, contact compactness, stress distribution characteristics and contact force probability distribution of the ore-rock dispersion, it realizes the quantitative characterization of the damage degree of ore-rock flow, and reveals the damage mechanism of mine storage wall. The results show that: (1) The friction between ore-rock particles, between ore-rock and well wall is an important reason for the change of the macroscopic flow form of ore-rock from “one” to “V” type. (2) The compactness and stress concentration of ores are increasing with the increase of storage depth, which is shown that with the increase of storage depth, the greater the probability of well wall instability. (3) The probability distribution of contact force strength between particles decreases exponentially in the whole process of ore drawing, in which the strong chain plays a major role in the stability of the dispersion system. (4) The number of overpressure and the overpressure coefficient can be used to quantitatively characterize the wall damage degree under the action of ore-rock flow. The dynamic side pressure decreases periodically in the form of exponential fluctuations, and the dynamic load formed by the ore-rock flow mainly played a role in the lower area of the ore storage section.

Using a simple model for internal heat evolution and mass-internal heat relations found for rocky exo planetary objects in the inner solar system we have inferred the phases of volcanism at earth ( EA) or host star ages (SA) in 52 potentially habitable rocky exo planets. We have also calculated the internal tidal heat contributions and magnetic moments of these exo planets. Based on these results we have inferred the probability of existence of life favouring geophysical conditions in the above exo planets at EA and SA. In M star associated exo planets, occurrences of super flares and long night periods may pose problems for the development of advanced life

Pulmonary arterial hypertension (PAH) is a chronic disease characterized by a progressive in-crease in mean pulmonary arterial pressure. Mutations in the BMPR2 and AQP1 genes have been described in familial PAH. The bone morphogenetic proteins BMP9 and BMP10 bind with high affinity to BMPR2. Administration of BMP9 has been proposed as a potential therapeutic strategy against PAH, although recent conflicting evidence dispute the effect of such practice. Considering the involvement of the above molecules in PAH onset, progression, and therapeutic value, we ex-amined the effects of modulation of BMP9, BMPR2, and AQP1 on BMP9, BMP10, BMPR2, AQP1, and TGFB1 expression in human pulmonary microvascular endothelial cells in vitro. Our results demonstrated that silencing the BMPR2 gene resulted in increased expression of its two main ligands, namely BMP9 and BMP10. Exogenous administration of BMP9 caused return of BMP10 to basal levels, while restored the decreased AQP1 protein levels and the decreased TGFB1 mRNA and protein expression levels caused by BMPR2 silencing. Moreover, AQP1 gene silencing also resulted in increased expression of BMP9 and BMP10. Our results might possibly imply that the effect of exogenously administered BMP9 on molecules participating in the BMP-signaling pathway could depend on the expression levels of BMPR2. Taken together, these results may pro-vide insight into the highly complex interactions of the BMP-signaling pathway.

In this work, we will study at a basic level, a series of possible new three-dimensional monoclinic allotropes of silicon, with sp3 hybridization, of the bct type; where hexahedrons and octahedrons are combined, with other cluster shapes, with basic silicon geometries such as: triangles ( Si3 ), squares ( Si4 ), pentagons ( Si5 ) and hexagons ( Si6 ); similar to two-dimensional, sp2 hybridized graphene allotropes. Calculating its electron density, bandgap energy and electronic mobility.

Semiconductors play a very important role in modern society. The improvement in performance of semiconductors is what has enabled the world to grow at such a fast pace. For decades scaling has been done through Moore’s law i.e performance improvements have been obtained due to transistor scaling where the number of transistors per unit area increase is what has contributed to the increase in performance. However, with transistor scaling reaching its limitations we need to find alternate methods to enhance silicon design to suit the computational need of modern society. To address this problem we will be looking into a few methods that enable performance scaling with a focus on analysing the most popular implementation of each in the industry.

Light trapping in single nanowires (NWs) are of vital importance for photovoltaic applications. However, circular NWs (CNWs) can limit its light-trapping ability due to high geometrical symmetry. In this work, we present a detailed study of light trapping in single NWs with an elliptical cross-section (ENWs). We demonstrate that the ENWs exhibit significantly enhanced light trapping compared with the CNWs, which can be ascribed to the symmetry-broken structure that can orthogonalize the direction of light illumination and the leaky mode resonances (LMRs). That is, the elliptical cross-section can simultaneously increase the light path length by increasing the vertical axis and reshape the LMR modes by decreasing the horizontal axis. We found that the light absorption can be engineered via tuning the horizontal and vertical axes, the photocurrent is significantly enhanced by 374.0% (150.3%, 74.1%) or 146.1% (61.0%, 35.3%) in comparison with that of the CNWs with the same diameter as the horizontal axis of 100 (200, 400) nm or the vertical axis of 1000 nm, respectively. This work advances our understanding of how to improve light trapping based on the symmetry breaking from the CNWs to ENWs and provides a rational way for designing high-efficiency single or self-assembled NW photovoltaic devices.

Thanks to advanced semiconductor microfabrication technology, chip-scale integration and miniaturization of lab-on-a-chip components, silicon-based optical biosensors have made significant progress for the purpose of point-of-care diagnosis. In this review, we provide an overview of the state-of-the-art in evanescent field biosensing technologies including interferometer, microcavity, photonic crystal, and Bragg grating waveguide-based sensors. Their sensing mechanisms and sensor performances, as well as real biomarkers for label-free detection, are exhibited and compared. We also review the development of chip-level integration for lab-on-a-chip photonic sensing platforms, which consist of the optical sensing device, flow delivery system, optical input and readout equipment. At last, some advanced system-level CMOS-chip packaging examples are presented, indicating the commercialization potential for the low cost, high yield, portable biosensing platform leveraging CMOS processes.

Silicon light funnels are three-dimensional subwavelength structures in the shape of inverted cones with respect to the incoming illumination. Light funnel arrays can serve as an efficient absorbing layers on account of their light trapping capabilities associated with the presence of high density complex Mie modes. Specifically, light funnel arrays exhibit broadband absorption enhancement of the of the solar spectrum. In the current study, we numerically explore the optical coupling between surface light funnel arrays and underlying substrates. We show that the absorption in LF array-substrate complex is higher than the absorption in LF arrays of the same height (~10% increase). This, we suggest, imply that a LF array serves as an efficient surface element that imparts additional momentum components to the impinging illumination, and hence optically excites the substrate by near-field light concentration, excitation of traveling guided modes in the substrate and mode hybridization.

A novel electrospun nanofiber was developed using polyamide-6 (PA) and ε-poly-L-lysine (PL). PA is a popular textile polymer having desirable mechanical and thermal properties, chemical stability, and biocompatibility. However, PA nanofibers are prone to bacterial growth and user discomfort. PL, a natural homopolyamide, is non-toxic, antimicrobial, and hydrophilic but lacks spinnability due to its low molecular weight. Given its similar backbone structure as PA, with an additional amino side chain, PL was integrated with PA to develop multifunctional nanofibers. This study explores a simple, scalable method to obtain PL nanofibers by utilizing the structurally similar PA as the base. The goal was to enhance the functionality of PA by addressing its drawbacks. The study demonstrates spinnability of varying concentrations of PL with base PA while exploring compositions with higher PL concentrations than previously reported. Electrospinning parameters were studied to optimize the nanofiber properties. The effects of PL addition on morphology, hydrophilicity, thermal stability, mechanical performance, and long-term antimicrobial activity of nanofibers were evaluated. The inclusion of PL in PA-based nanofibers resulted in super hydrophilicity, increased tensile strength, and efficient antimicrobial properties with long-term stability. These enhanced characteristics hold promise for the composite nanofiber’s application in medical and protective textiles.

Approximate entropy (ApEn) and sample entropy (SampEn) are statistical indices designed to quantify the regularity or predictability of time series data. Although ApEn has been a prominent choice for use in the analysis of non-linear data, it is currently unclear as to which method and parameter selection combination is optimal for its application in biomechanics. The goal of this research was to examine the differences between ApEn and SampEn related to center of pressure (COP) data during tandem standing balance tasks, while also changing the tolerance window, r. Six participants completed five, 30-second trials, feet-together and tandem standing with eyes-open and eyes-closed. COP data (fs = 60 Hz, downsampled from 1200 Hz) from ground reaction force platforms were collected. ApEn and SampEn were calculated using a constant vector length, i.e., m = 2, but differing values of r (tolerance window). For each of the participants, four separate one-way analysis of variance analyses (ANOVA) were conducted for ApEn and SampEn in the anterior-posterior (AP) and medial-lateral (ML) directions. Dunnett's intervals were applied to the one-way ANOVA analyses to determine which tandem conditions differed significantly from the baseline condition. ApEn and SampEn provided comparable results in the predictability of patterns for different stability conditions, with increasing instability, i.e., tandem eyes closed postures, being associated with greater unpredictability. The selection of r had a relatively consistent effect on mean ApEn and SampEn values across r = 0.15 * SD to r = 0.25 * SD, where both entropy methods tended to decrease as r increased. Mean SampEn values were generally lower than ApEn values. The results suggest that both ApEn and SampEn indices demonstrated relative consistency and were equally effective in quantifying the level of the center of pressure signal regularity during quiet tandem standing postural balance tests.

This research is related to the eco-hydrological problems of herbaceous wetland drying and biodiversity loss in the floodplain lakes of the Middle Basin of the Biebrza river (Poland). An experiment was set up, whose main goals were: (i) mapping the vegetation types and the temporarily or permanently flooded areas, and (ii) comparing the usefulness of C-band Sentinel-1A (S1A) and X-band TerraSAR-X/TanDEM-X (TSX/TDX) for mapping purposes. The S1A imagery was acquired on a regular basis using the dual polarization VV/VH and the Interferometric Wide Swath Mode. The TSX/TDX data were acquired in quad-pol, a fully polarimetric mode, during the Science Phase. The paper addresses the following aspects: i) wetland mapping with S1A multi-temporal series; ii) wetland mapping with fully polarimetric TSX/TDX data; iii) comparing the wetland mapping using dual polarization TSX/TDX subsets, i.e. HH-HV, HH-VV and VV-VH; iv) comparing wetland mapping using S1A and TSX/TDX data based on the same polarization (VV-VH); v) studying the suitability of the Shannon Entropy for wetland mapping; and vi) assessing the contribution of interferometric coherence for wetland classification. The experimental results show main limitations of the S1A dataset, while they highlight the good accuracy that can be achieved using the TSX/TDX data, especially those taken in fully polarimetric mode.

Abstract: This article reports the results of an ecological study of cancer incidence rates by state in the US for the period 2016-2020. The goals of this study were to determine the extent to which solar UVB doses still reduced cancer risk compared to findings reported in 2006 for cancer mortality rates for the periods 1950–1969 and 1970-1794 as well as cancer incidence rates for the period 1998–2002 and to determine which factors were recently associated with cancer risk. The cancer data for non-Hispanic white (European American) men and women were obtained from the Centers for Disease Control and Prevention. Indices were obtained for solar UVB at the surface for July 1992, and alcohol consumption, and diabetes and obesity prevalence near the 2016–2020 period. Lung cancer incidence rates were also used in the analyses as a surrogate for smoking, diet, and air pollution. The cancers for which solar UVB is significantly associated with reduced incidence are bladder, brain (males), breast, corpus uteri, esophageal, gastric, non-Hodgkin’s lymphoma, pancreatic, and renal cancer. Lung cancer was significantly associated with colorectal, laryngeal, and renal cancer. Diabetes was also significantly associated with breast, liver, and lung cancer. Obesity prevalence was significantly associated with breast, colorectal and renal cancer. Alcohol consumption was associated with bladder and esophageal cancer. Thus diet has become a very important driver of cancer incidence rates. The role of solar UVB in reducing risk of cancer has been reduced due to people spending less time outdoors, wearing sunscreen that blocks UVB but not UVA radiation, and population increases in overweight and obesity, which lowers 25-hydroxyvitamin D concentrations and generates systemic inflammation, a risk factor for cancer. The dietary approach that would reduce the risk of diabetes, obesity, lung cancer, and, therefore cancer, would be one based mostly on whole-plants and restrictions on red and processed meats and ultraprocessed foods. Solar UVB exposure for a few minutes before applying sunscreen and taking vitamin D supplements would also help reduce risk of cancer.Keywords: alcohol consumption; cancer incidence;

Neuro-rehabilitation services are essential in reducing post-stroke impairments, enhancing independence, and improving recovery in hospital and post-discharge. However these services are therapist-dependent and resource intensive. Patients’ disengagement and boredom in stroke units are common which adversely affect functional and psychological outcomes. Novel techniques such as use of iPads™ are increasingly researched to overcome such challenges. The aim of this review is to determine the feasibility, effectiveness, acceptability, and barriers to the use of iPads™ in stroke neuro-rehabilitation. Four databases and manual literature search were used to identify published studies using the terms “iPad”, “Stroke”, and “neuro-rehabilitation”. Studies were included in accordance with the review selection criteria. A total of 16 articles were included in the review. The majority of the studies focused on iPads use in speech and language therapy. Although of small scale, the studies highlighted that iPads are feasible, have the potential to improve rehabilitation outcomes, and can improve patient’s social isolation. Patients’ stroke severity and financial limitations are some of the barriers highlighted in this review. This review presents preliminary data supportive for the use of iPad technology in stroke neuro-rehabilitation. However, further research is needed to determine impact on rehabilitation goals acquisition, clinical efficacy, and cost-efficiency.

Protection suit is vital for fireman’ safety. Traditional protection suit just physically protects fireman from empyrosis, but can not locate the body injury position from the impact debris. Herein, we present a wearable impact debris positioning system for fireman protection suit alarming based on accelerometer array. The wearable piezoelectric accelerometers with distribute regularly on the suit to detect the vibration on different body parts, which is conducive to positioning injured body parts. In addition, the injured parts can be displayed on the dummy body model on the upper computer with a higher localization accuracy of 4 cm. The positioning alarm system has a rapid response time of 0.11ms attributing to smart signal processing method. This work provides a reliable and smart method for locating and assessing the body injury position from the impact debris, which is significant for fire disaster commander to rescue injured fireman in time.

This paper presents design and optimization of a small-size electromagnetic induction heating control system powered by a 3.7V-900mAh lithium battery and featuring an LC series resonant full bridge inverter circuit, which can be used in small size materials heating applications, such as micro medical devices. The effects of resonant capacitance, inductor wire diameter, heating tube material and wall thickness are studied to maximize the heating rate of the workpiece and meantime reduce the temperature rise of the NMOS transistor. The optimal circuit configuration meeting the design requirements was finally identified via comparing the operational parameters and NMOS transistor loss under different circuit conditions. The validation experiments were conducted on a designed electromagnetic induction smoking devices. The results indicate that under an output current of 4.6A, the heating tube can reach up to the temperature target of 250℃ within 11 seconds, and all NMOS transistors stay below 50°C in a 5 minutes heating process.

This study explores the current landscape of social value (SV) research in the construction industry, analyzing global trends and identifying future research directions. Using bibliometric analysis, research published in Elsevier Scopus database from 2013 to 2023 was extracted using the keywords "social value" AND "construction industry." Results indicate a focus on social value indicators, socioeconomic impacts, project management, innovative practices, and cross-sector collaborations. The study also reveals a lack of attention to SV in African countries' construction sectors. By highlighting research areas and identifying gaps, this study contributes to academic literature, suggesting the need for guidelines, particularly in developing countries, and advocating for further research on SV in the built environment and strategies for global social value creation.

The study findings revealed significant variability in various wood properties among different genetic families, although the static modulus of elasticity did not exhibit significant differences between the chosen genetic families. All measured wood properties decreased from the bottom to the top of the model trees. Wood hardness displayed a moderately negative correlation with wood density and weak correlations with MOE and MOR. Given the weak correlations between wood hardness and other wood mechanical properties, it is suggested that the MOEdyn would be a more suitable trait for genetic studies.

A dioxomolybdenum catalyst [(MoO2Cl2-O-MoO2Cl2)(L)] (1) (with L (1S,2S)-N,N´-bis(2-pyridinecarboxamide)-1,2-cyclohexane) was prepared and used as catalyst for the desulfurization of a multicomponent model fuel containing the most refractory sulfur compounds in real fuels. This complex showed to have a high efficiency to oxidize the aromatic benzothiophene derivative compounds present in fuels, mainly using a biphasic 1:1 model fuel/MeOH system. This process conciliates catalytic oxidative and extractive desulfurization, occurring the oxidation of the sulfur compounds in the polar organic solvent. The oxidative catalytic performance of (1) showed to be influenced by the presence of water in the system. Using 50% aq. H2O2 it was possible to reuse the catalyst and the extraction solvent MeOH during ten consecutive cycles without loss of desulfurization efficiency.

Revealing the spatial distribution mechanism of the coupling effect between soil water and salt is essential for managing saline-alkali farmland. This study utilized the multifractal method to analyze soil water and salt under varying water content levels in arid saline-alkali farmland. Soil samples were collected on the second (S1), fifth (S2), eighth (S3), eleventh (S4), and fourteenth (S5) days after a rainfall event. The findings showed that a significant decrease in soil water content, contrasting with an increase in soil salt content throughout the soil layers post-rainfall. As water content decreased, the spatial variability of soil water initially increased from S1-3 and then decreased, while the spatial variability of soil salt decreased. The spatial distribution between soil water and salt exhibited a high correlation at S3-4 (with relative water content of soil ranging from 0.52 to 0.75) due to their coupling effect. However, soil salt was unevenly leached by rainfall at high water content levels (S1-2) and precipitated at low water content levels (S5), resulting in low spatial variability correlations between soil water and salt. This study elucidated the coupling process of soil water and salt, identifying their spatiotemporal distribution mechanism in dryland agricultural areas.

Despite the partial disclosure of driving scenario knowledge graphs, they still fail to meet the comprehensive needs of intelligent connected vehicles for driving knowledge. Current issues include the high complexity of pattern layer construction, insufficient accuracy of information extraction and fusion, and limited performance of knowledge reasoning models. To address these challenges, a hybrid knowledge graph method was adopted in the construction of the Driving Scenario Knowledge Graph (DSKG). Firstly, core concepts in the field were systematically sorted and classified, laying the foundation for the construction of a multi-level classified knowledge graph top-level ontology. Subsequently, by deeply exploring and analyzing the Traffic Genome data, 34 entities and 51 relations were extracted and integrated with the ontology layer, achieving the expansion and updating of the knowledge graph. Then, in terms of knowledge reasoning models, an analysis of the training results of the TransE, Complex, Distmult, and Rotate models in the entity linking prediction task of DSKG revealed that the Distmult model performed the best in metrics such as hit rate, making it more suitable for inference in DSKG. Finally, a standardized and widely applicable Driving Scenario Knowledge Graph was proposed. The DSKG and related materials have been publicly released for use by industry and academia.

Elevated serum uric acid (sUA) is associated with risk of developing cardiovascular disease (CVD). Here, we examined the prognostic significance of sUA and exercise capacity in 411 Japanese adults (age, ≥65; mean, 81 years) hospitalized for worsening CVD. Mean sUA was significantly higher in the 23% of patients on an sUA-lowering agent than in those not. When the patients were stratified by sUA into three groups (7.0 mg/dL), the high sUA group had significantly worse peak VO2 and composite endpoint (rehospitalization due to worsening CVD and all-cause mortality) compared with low and moderate sUA groups (P < 0.001). When the patients were stratified by sUA into five groups (sUA 10.0 mg/dL), the incidence of the composite endpoint was significantly higher in the highest sUA group compared with that in the reference group, but only in women. Univariate Cox regression analysis, but not a multivariate analysis, indicated that sUA was significantly associated with the composite endpoint. Although sUA and exercise capacity may have some degree of prognostic significance in older patients with CVD, this significance may differ between men and women.

Aflatoxin M1 (AFM1), a carcinogenic toxin, mainly contaminates cow milk and poses significant challenges to the dairy industry and, thereby, public health in most tropical countries, including Ethiopia. This study aimed to investigate the prevalence and level of AFM1 in raw cow milk collected from Specialized Dairy Farms and Milk Vendors in three Urban Centers: Chiro town, Dire Dawa, and Harar cities in Eastern Ethiopia. 180 milk samples were collected from two major Milk Sources: Specialized Dairy Farms (N=90) and Milk Vendors (N=90) using a simple random sampling technique. AFM1 was analyzed using high-performance liquid chromatography. The study revealed that, 63.9% (115/810) prevalence and 0.179±0.48µg/L mean of AFM1 level in milk, which 39.13% and 26.08% exceed the tolerable limits of EU and FDA respectively. A 40.0% prevalence and 0.344±0.72µg/L average of AFM1 in the milk from Dire Dawa city was significantly higher than the samples from other Urban Centers. However, 30.43% and 29.57% prevalence as well as 0.055±±0.13µg/L and 0.140±0.33µg/L average of AFM1 in milk from Chiro town and Harar city, respectively were not significant. Furthermore, milk samples from Dairy Farms revealed a higher prevalence (57.39%) and level (0.252±0.64µg/L) of AFM1 than Milk Vendors, with a prevalence of 42.61% and an average of 0.107±0.21µg/L. Therefore, this study concludes that substantial milk samples were contaminated by AFM1 and urges the need to enhance farmers' awareness on mitigation.

The influence of growth temperature on the crystalline quality and optical properties of AlGaN at 325 nm, grown using plasma-assisted molecular beam epitaxy (MBE), was investigated. The growth temperature exhibited a significant impact on the growth mode and surface morphology. Specifically, at a growth temperature of 750 degrees Celsius, when appropriate Al and Ga flow rates were employed, the AlGaN layer exhibited exceptional surface morphology and favorable optical properties. The optical properties of the AlGaN material were explored, revealing the presence of two distinct non-radiative recombination centers characterized by different activation energies. The minority carrier lifetimes were measured as 560 ps at 10 K and 64 ps at room temperature. The underlying mechanism was analyzed from the perspective of carrier dynamics, shedding light on the observed phenomena.

Pretreatment of cells with proteolysis inhibitors diminished intensity and changed shape of DNICs specific EPR signal in a treatment time-dependent manner. The level of DNIC formation was significantly influenced by the presence of protein degradation products. Interestingly, formation of HMWDNICs depended on the availability of LMWDNICs. The extent of glutathione involvement in the in vivo formation of DNICs is minor yet noticeable, aligning with our prior research findings.

Herein, we present the design technique of a resonant rectifier for piezoelectric (PE) energy harvesting. We propose two diode equivalents to reduce the voltage drop in the rectifier operation, a minuscule-drop-diode equivalent (MDDE) and a low-drop-diode equivalent (LDDE). The diode equivalents are embedded in resonant rectifier integrated circuits (ICs), which use symmetric bias-flip to reduce the power wasted for charging and discharging the internal capacitance of a PE transducer. The self-startup function is supported by synchronously generating control pulses for the bias-flip from the PE transducer. Two resonant rectifier ICs, using both MDDE and LDDE, are fabricated in a 0.18 μm CMOS process and their performances are characterized under external and self-power conditions. Under the external-power condition, the rectifier using LDDE delivers an output power POUT of 564 μW and a rectifier output voltage VRECT of 3.36 V with a power conversion efficiency (PCE) of 90.1%. Under self-power conditions, the rectifier using MDDE delivers a POUT of 288 μW and a VRECT of 2.4 V with a corresponding PCE of 74.6%. The result shows that the power extraction capability of the proposed rectifier is 5.9 and 3.0 times higher than that of a conventional full-bridge rectifier.

Proteomics research has become one of the most important topics in the fields of life science and natural science. At present, research on protein–protein interaction networks (PPINs) mainly focuses on detecting protein complexes or function modules. However, existing approaches are either ineffective or incomplete. In this paper, we investigate function module detection mechanisms in PPIN, including open databases, existing detection algorithms and recent solutions. After that, we describe the proposed solution based on simplified swarm optimization (SSO) algorithm and gene ontology knowledge. The proposed solution implements SSO algorithm for clustering proteins with similar function, and imports biological gene ontology knowledge for further identifying function complexes and improving detection accuracy. Furthermore, we use four different categories of species dataset for experiment: Fruitfly, Mouse, Scere, and Human. The testing and analysis result show that the proposed solution is feasible, efficient and could achieve a higher accuracy of prediction than existing approaches.

The growing expansion of the economy and population has resulted in an increased inclination towards the utilization of groundwater resources. Conducting a geophysical survey is a widely employed method for subsurface mapping and the detection of groundwater. A geophysical study was conducted in Nanshan township, Huarong County, located in the Hunan province of the South-Central region of China. The investigation involved the utilization of a 2D Electrical Resistivity Imaging technique employing forward and inverse pole-dipole electrode array. A total of six survey lines were established, each with an electrode distance from the nearest measuring point to exceeding 800 m. The maximum current electrode separation was utilized in this setup. The spacing between the electrical resistivity sounding points was established at regular intervals. The findings from the exploration indicate the existence of multiple faults within the surveyed region. The study additionally identified two regions of structural failure, which occurred due to the convergence of faults oriented in different directions. This convergence led to the fracturing of rocks, an increase in water content, and a decrease in resistivity. The findings from the exploration were utilized in the formulation of five verification target boreholes. The results of this study offer significant insights that can inform future investigations into groundwater exploration endeavors within the region.

Keywords: olfactory rehabilitation; chronic pain; fMRI;

Diacylglycerol kinase (DGK) is a lipid kinase that phosphorylates diacylglycerol (DAG) to generate phosphatidic acid (PA). Based on converting one important signaling molecule (DAG) to another (PA), DGK plays an important role in plant responses to abiotic stress including waterlogging stress. However, no studies have been reported on the characterization of the DGK gene family in the waterlogging-tolerant kiwifruit germplasm, Actinidia valvata Dunn. Here, we identified 18 AvDGK genes in the A. valvata genome. The phylogenetic analysis showed that AvDGKs can be classified into three clusters, and members within the same cluster have similar domain distribution, exon-intron structures and conserved motif compositions. Chromosome localization analysis revealed that all the AvDGK genes are located across 18 different chromosomes. There were 29 duplicated gene pairs in kiwifruit and all had undergone purifying selection during evolution. Promoter cis-element analysis revealed that the cis-elements within AvDGK genes are associated with multiple functions, including phytohormone signal transduction, stress response, and plant growth and development. The expression pattern analyses indicated that AvDGK play an important role in the fruit development and plant response to waterlogging stress. AvDGKs gene family in the tetraploid A. valvata genome might promote PA synthesis and subsequent signal transduction both under short-term and long-term waterlogging stress. These results provide information regarding the structural characteristics and potential function of DGK genes within kiwifruit and lay a fundamental basis for further research into breeding for enhancing the kiwifruit’s tolerance to waterlogging stress.