This paper reviews the measurement challenges associated with 3D scanning techniques in civil engineering. It explores the practical aspects of scanning buildings and complex surfaces through various case studies. The paper details the conventional use of Terrestrial Laser Scanning (TLS) for reconstructing the technical documentation of a hall. It then describes an unconventional application of this technique for measuring an ETICS (External Thermal Insulation Composite System) wall, aiming to detect microdeformations caused by environmental factors controlled within a climatic chamber. The measurements of the insulated wall were subsequently repeated using a metrological grade laser scanner. Numerical data was analyzed with inspection engineering methods. This approach yielded qualitative and quantitative results. Although the qualitative results were consistent, the quantitative data revealed some inconsistencies. To address discrepancies in the quantitative data, a comparative analysis was performed, which highlighted critical findings and areas of divergence.

Laser scanning 3D imaging technology, because it can get accurate three-dimensional surface data, has been widely used in the search for wrecks and rescue operations, underwater resource development, and other fields. At present, the conventional underwater rotating laser scanning imaging system maintains a relatively fixed light window. However, in low-light situations underwater, the rotation of the scanning device causes some degree of water fluctuation, which warps the light strip data that the system sensor receives about the object's surface. To solve the problem, this research studies an underwater 3D scanning and imaging system that makes use of a fixed-light window and a spinning laser (FWLS). A refraction error compensation algorithm is investigated that is based on the fundamentals of linear laser scanning imaging and the dynamic refraction mathematical model is established by the motion of the imaging device. During the imaging process, the incident angle between the laser and the light window varies due to the scanning mode of the system. The experimental results show that the reconstruction radius error is reduced by 60% (from 2.5 mm to about 1 mm) when the measurement data for a standard sphere with a radius of 20 mm are compensated. Moreover, the compensated point cloud data exhibits a higher degree of correspondence with the model of the standard spherical point cloud. This study has a specific reference value for the refractive error analysis of an underwater laser scanning imaging system, and it provides certain research ideas for the subsequent refractive error analysis of various scanning imaging modalities.

The article proposes an indirect measurement method based on a dimensional and shape analysis of forgings for the evaluation of the manufacture and the proper operation of the key elements of the crank press, in which after modernization, a quick tool assembly based on SMED (Single Minute Exchange of Die) was implemented. As a result of the introduced changes aiming at improving the forging aggregate and increasing the production efficiency, errors were observed on the manufactured products-forgings in the form of twists and joggles. The preliminary analysis showed that they can be clearances and dynamic deformation in the kinematic chain, the occurrence of side forces during automatic forging of the forging in a two-component system (a long, thin element), as well as the design and construction errors in the joining of the SMED instrument with the table tops of the press. In order to solve the presented problem, in the first place, a separate dimensional and shape analysis was made of selected elements of the press and the instrumentation with the use of the 3D scanning method with the purpose to analyze the construction tolerances of the key elements of the press geometry. Next, an evaluation of the effect of clearances and dynamic deformations of the press as well as the force distribution during the forging process was made through numerical modelling. Despite all of the above, such an approach did not make it possible to solve the problem. A proprietary method with the use of 3d reverse scanning was proposed, which allowed to solve the problem of forgings errors. Based on the measurement results and analyses for a few variants of production cycles the necessary changes was obtained, making it possible to minimize the errors and obtain proper products in respect of geometry and quality.

This paper presents a comprehensive review of the transformative impact of 3D printing technology on smart cities. As cities face rapid urbanization, resource shortages, and environmental degradation, innovative solutions such as additive manufacturing (AM) offer potential pathways for sustainable urban development. By synthesizing 66 publications from 2015 to 2024, the study examines how 3D printing improves urban infrastructure, enhances sustainability, and fosters community engagement in city planning. Key benefits of 3D printing include reducing construction time and material waste, lowering costs, and enabling the creation of scalable, affordable housing solutions. The paper also addresses emerging areas such as the integration of 3D printing with digital twins (DT), machine learning (ML), and AI to optimize urban infrastructure and predictive maintenance. It highlights the use of smart materials and soft robotics for structural health monitoring (SHM), and repairs. Despite the promising advancements, challenges remain in terms of cost, scalability, and the need for interdisciplinary collaboration among engineers, urban planners, and policymakers. The findings suggest a roadmap for future research and practical applications of 3D printing in smart cities, contributing to the ongoing discourse on sustainable and technologically advanced urban development.

High rates of phosphorus (P) currently being applied to soils for the production of vegetables in the Mekong Delta, Vietnam has led to the concern of its negative effect on the economics and the environment. This research presents a comprehensive study on the determination of P supplying capacity in this region of Vietnam to examine the possibility of reducing P fertilizer input. One hundred twenty (120) soil samples were collected to evaluate total P and Bray 1 available P in the soils. Phosphorus maximum sorption, degree of P saturation, P release, and the effect of P fertilizer on corn (Zea mays L.) yield in greenhouse and fields were also determined. Total P concentrations of 56.7% soil samples evaluated yielded high P concentrations (>560 mg P/kg), while 74.2% of the samples had high Bray 1 available P concentrations (>20 mg P/kg soil). Maximum P sorption ranged from 149 to 555 mg P/kg soil, respectively and has negative correlation to available P (r = - 0.63*), degrees of P saturation ranged from 0.63 to 5.46% correlated to available P (r = 0.98**) and maximum P release ranged from 1.2 to 61.9 mg P/kg soil, respectively correlated to available P (r = 0.96**). Corn grown in soils with available P concentrations >15 mg P/kg did not respond to P fertilizer in greenhouse or field experiments. We conclude that many farmers in this region can reduce P fertilizer input, thus increasing their profits and reducing negative environmental impacts associated with excess soil P for sustainable agriculture.

Orthostatic hypotension (OH) is a condition marked by a significant drop in blood pressure upon standing, resulting from impaired autonomic regulation of vascular tone and blood volume. This study investigates the prevalence, physiological mechanisms, and occupational risk factors for OH among high-risk professions in Nepal, such as traffic police, security guards, and shopkeepers. Using a cross-sectional design, participants were evaluated for blood pressure variability, autonomic function, and fluid balance. The findings reveal a high incidence of OH, linked to reduced baroreceptor sensitivity and impaired sympathetic activation due to prolonged standing and inadequate hydration. This study highlights the need for tailored clinical interventions and workplace modifications to mitigate OH in vulnerable occupational groups.

Sewage sludge is an organic waste generated in waste-water treatment plants with certain content of nutrients, what may potentially be used as a source of slow release fertilizer, especially as phosphorus (P) source, but it demands some pre-treatment and the content of P is much lower compared to soluble mineral fertilizers. For these reasons, composted sewage sludge was used to manufacture pelletized organomineral fertilizers, mixing it with the inorganic sources monoammonium phosphate (MAP) and AshDec® (ASD) (thermochemically incinerated sewage sludge). The fertilizers were physiochemically characterized and evaluated as to the dynamics of soil P solubilization, and the forms of P remaining according to its lability. The sources evaluated were: organic compost of sewage sludge powder (SSC), pelletized SSC (SCP), pelletized organominerals SSC+MAP (S+MAP) and SSC+ASD (S+ASD), ASD alone, all compared to a soluble mineral fertilizer (MAP), and a control without P fertilizer. A test was conducted in leaching columns with 50 g of soil (Oxisol), where the fertilizers were applied at a dose of 100 mg P/column, and 30 mL of water or 2% citric acid were added daily for 30 consecutive days. The collected leachates had pH measured and P content determined. Pelletizing process resulted in denser products and promoted more gradual P release. The organomineral S+MAP was the most water-soluble recycled source, solubilizing about 70% of the total P, while the others presented much lower solubilization (<20%). In contrast, all fertilizers showed high solubility in 2% citric acid (except for S+ASD). After leaching, the greatest amount of P remaining in the soil as labile and moderately labile. Composting and the AshDec process produced materials with slow P solubilization, which would be favoured to solubilize in acidic soils and acidic rhizosphere conditions. In turn, the organomineral mixture of SSC with a highly soluble mineral fertilizer (MAP) resulted in a promising product with intermediate nutrient solubility, better synchronized with crop demand, thus increasing efficiency in P use.

The agricultural sector is vital to the economies of many countries, particularly in developing country, providing livelihoods for millions and significantly contributing to GDP, food security, and social stability. Off-takers play a critical role in addressing these challenges by providing market certainty through predetermined purchase agreements. Engaging in contract farming and offering capital, technical assistance, and market access, off-takers help stabilize income, facilitate capital access, enhance technology adoption, and ensure business continuity. This research employs the Systematic Literature Review (SLR) method and secondary data analysis. Based on the review, the multifaceted benefits of agricultural off-takers include increased production and fostering entrepreneurial skills among farmers. Hence, fostering partnerships between farmers and off-takers is crucial for enhancing agricultural competitiveness, sustainability, and farmer well-being. Leveraging off-takers' potential and promoting collaboration within agricultural clusters can foster thriving agricultural ecosystems, ensuring food security and economic prosperity in rural communities.

In this paper, we introduce the (ρ,q)-analogue of the p-adic factorial function. By utilizing some properties of (ρ,q)-numbers, we obtain several new and interesting identities and formulas. We then construct the p-adic (ρ,q)-gamma function by means of the mentioned factorial function. We investigate several properties and relationships belonging to the foregoing gamma function, some of which are given for the case p = 2. We also derive more representations of the p-adic (ρ,q)-gamma function in general case. Moreover, we consider the p-adic (ρ,q)-Euler constant derived from the derivation of p-adic (ρ,q)-gamma function at x = 1. Furthermore, we provide a limit representation of aforementioned Euler constant based on (ρ,q)-numbers. Finally, we consider (ρ,q)-extension of the p-adic beta function via the p-adic (ρ,q)-gamma function and we then investigate various formulas and identities.

Objectives: In Nigeria, modern contraceptive use remains relatively low despite numerous efforts to increase awareness and accessibility. This study examined the geopolitical factors influencing modern contraceptive use in North-central Nigeria Design: Using data from the 2021 Nigeria Multiple Indicator Cluster Survey, this study quantitatively investigated the factors influencing modern contraceptive use among women of reproductive age. The data were analyzed using R studio. Respondents' characteristics were described using frequency and percentage. A logistic regression model was employed to identify factors associated with modern contraceptive usage in the north-central region of Nigeria. Bivariate logistic regression was carried out between the explanatory and response variables. Settings: This study focused specifically on the north-central zone of Nigeria comprising 6 states, namely, Benue, Kogi, Kwara, Nasarawa, Niger, and Plateau states with the Federal Capital Territory (FCT). Results: Nearly one-third (30.1%) of the respondents are above 35 years of age. 3 out of every 5 (61.2%) respondents are currently married. This study found that the average modern contraceptive usage among women of reproductive age in north Central Nigeria is less than 15%. Age, education, childbirth delivery method, number of children, access to media, and state of residence are key drivers of modern contraceptive adoption and utilization among women of reproductive age in north-central Nigeria. Conclusion: This study finds it plausible to increase the awareness and sensitization of modern contraceptives and contraceptive usage in this region. There is a need for health education on the benefits and relevance of modern contraceptive usage.

Introduction: Early childhood caries is a significant public health problem among preschool children. The COVID-19 pandemic, which restricted dental services, altered family dynamics, affected child development, and created new demands on caregivers, may have exacerbated this issue. Objective: Analyze the occurrence and severity of caries and identify associated factors in preschool children attending public municipal daycare centers in Salvador, Bahia, Brazil, Methodology: A cross-sectional epidemiological study was conducted to investigate caries in children aged 2 to 5 years in 2022 and 2023. Caries was assessed using the decayed, extracted, filled, and missing teeth (DEFT) index, and prevalence was calculated. Sociodemographic, family dynamic, dietary, and healthcare utilization data were obtained through a questionnaire. After descriptive and exploratory analyses, robust Poisson multivariable regression was conducted at a 5% significance level, considering socioeconomic, psychosocial, and behavioral aspects. Results: A total of 440 preschoolers participated, with a mean age of 55 months. The majority were Black or mixed race (88.86%) and female (52.73%). The prevalence of caries was 30.91% and the mean DEFT score was 1.1. In the multivariable analysis, low family income (up to one minimum wage) and not playing outdoors during the pandemic were associated with a higher prevalence of caries. Conclusion: The prevalence and severity of caries remain high, and the pandemic has contributed to the maintenance of this epidemiological scenario. Public health measures and policies promoting social justice should be planned to improve oral health conditions in childhood.

In this study, we propose a conservative and compact finite difference scheme designed to preserve both the mass change rate and energy for solving the sixth-order Boussinesq equation with the surface tension. Theoretical analysis confirms that the proposed scheme achieves second-order accuracy in temporal discretization and fourth-order accuracy in spatial discretization. The solvability, convergence, and stability of the difference scheme are rigorously established through the application of the discrete energy method. Additionally, a series of numerical experiments are conducted to illustrate the effectiveness and reliability of the conservative scheme for long-time simulations.

In this paper, we introduce a new class of $(p,q)$-analogue type of Fubini numbers and polynomials and investigate some properties of these polynomials. We establish summation formulas of these polynomials by summation techniques series. Furthermore, we consider some relationships for $(p,q)$-Fubini polynomials associated with $(p,q)$-Bernoulli polynomials, $(p,q)$-Euler polynomials and $(p,q)$-Genocchi polynomials and $(p,q)$-Stirling numbers of the second kind.

This study examines the evolution and eventual decline of the spirit of primitive federalism within Confucianism, tracing its trajectory from the time of the Duke of Zhou and Confucius to the significant reinterpretations by Dong Zhongshu. The Duke of Zhou's establishment of a confederation-like system and the "Zhou ritual norms" laid the groundwork for a political structure that embraced diversity and distributed power among states, reflecting a proto-federalist concept. Confucius's teachings continued this legacy, advocating for a return to the systems of the Duke's era, where both the central government and local states shared responsibilities and rights. The crux of this study lies within its fourth section, which narrates a tale of transformation happened under Emperor Wu of Han, where Dong Zhongshu distorted the original Confucianism and reinterpreted it as a centralized ideology. In Confucian theory, the shift involved the suppression of alternative philosophies, the establishment of Confucianism as the state's dominant ideology, and a reinterpretation of Confucianism that supported an centralized framework and cultural assimilation. In political practice, he re-envisioned the role of feudal lords as administrative extensions of a centralized government, effectively eroding local autonomy and shifting towards a unified, centralized system. Under the auspices of political authority, Confucian theory was transformed from a federalist theory promoting diversity, inclusivity and advocating decentralization, to one that legitimized a centralized and unified system.

Automation is transforming ship design by enhancing flexibility, efficiency, and accuracy in Computer-Aided Ship Design (CASD). This review highlights advancements in automation and parametric techniques that streamline the design process. Variable geometry and task automation improve performance optimization, enabling designers to concentrate on complex elements. The review will talk about advanced tools and methodologies, their effects on design optimization, production workflows, and some of the challenges associated with software interoperability and increased design complexity. It will also look at how AI and machine learning can be leveraged for better automation. The review identifies several future opportunities in automated ship design but frames such technologies as revolutionary in the shipbuilding sector and highlights their potential to bring significant transformation to shipping.

Photocatalytic water splitting offers a promising route for sustainable hydrogen production, but its efficiency remains limited by complex interactions between material properties, operating conditions, and reaction mechanisms. This study presents a data-driven approach to optimize photocatalytic water splitting for enhanced hydrogen evolution. By integrating experimental data, density functional theory calculations, and machine learning algorithms, we identified key descriptors governing photocatalyst performance. A predictive model was developed to screen optimal catalyst compositions, morphologies, and operating conditions, leading to a significant increase in hydrogen production rates. The results demonstrate the potential of data-driven optimization to accelerate the discovery of high-performance photocatalysts, paving the way for scalable and efficient solar-driven hydrogen production.

This paper explores the intersection of geometry and music, investigat- ing how mathematical structures shape musical theory, composition, and perception. It begins by examining the geometric foundations of pitch organization, including the circular representation of pitch classes and the tonal space. We then explore rhythmic structures through symmetry, analysing how patterns in time are geometrically conceived. Finally, the study examines more recent developments in computational music theory, such as the use of topological data analysis to model musical transformations and voice leading.

Polluting discharges are produced at a rate that is inexorably rising in tandem with human activity development. Eutrophication and other matters, such as offensive aquatic life, require wastewater to be treated before being discharged into the environment. Prior releasing into water bodies, the treated waters must to undertake laboratory analysis. For this purpose, an analysis using standard methods was carried out at the Laboratory Waterworks in Debrecen on various samples taken from various wastewater treatment plants (sewage treatment plants) in Hungary. The overall objective of this study was to assess the quality of the effluents from the fourteen (14) wastewater treatment plants and investigate their efficiency by measuring various physicochemical parameters and microbiological parameters as excellent indicators to evaluate the performance of the studied wastewater treatment plants. The microbiological indicator monitored was the heterotrophic count (HPC) by estimating its total number, which provides useful information for the assessment and monitoring of water samples. The determination of physicochemical parameters included biological oxygen demand (BOD5), chemical oxygen demand (COD) and nitrite -N (NO2), ammonia-N (NH3-N), nitrate-N (NO3) total phosphorus (TP), Kjeldahl- Nitrogen (organic N+ammonia-N) (TKN), total inorganic N (TI), total suspended solids (TSS) and total nitrogen (TN). The performance of the wastewater treatment plants examined was checked and the results were conclusive. In the future, solutions should be applied to these wastewater treatment plants and some recommendations are suggested.

Formaldehyde is generated via the biochemical and chemical pathways, and it widely exists in foods. Its chronic exposure causes carcinogenic, neurotoxic, reproductive, allergic, immunological, genetic and respiratory toxicities. However, food-sourced formaldehyde is usually neglected due to its rapid metabolism after intake. Compared with its residual level in processed foods, a large proportion of formaldehyde disappears because of its high reactivity. Nevertheless, its elimination reaction mechanism and the potential consequences remain unclear. In this review, the disappearing pathway of formaldehyde from two aspects, the formation of formaldehyde-derived toxins and aromas, was reviewed. This review article may help food scientists take appropriate strategies to use the beneficial reactions of formaldehyde or divert its harmful effects to beneficial ones.

Employee turnover is a significant issue for financial institutions, impacting productivity, increasing recruitment costs, and disrupting critical operations. In this project, this study aimed to predict employee turnover using a dataset containing attributes such as employee satisfaction, performance, and tenure. By framing the task as a binary classification problem, this study employed CatBoost and XGBoost, two advanced regression-based algorithms, to develop predictive models. This paper's analysis demonstrated that CatBoost outperformed XGBoost across all evaluation metrics, including MAE, MSE, RMSE, and R², making it the more effective model for predicting turnover in the financial sector. The study highlights key factors contributing to employee attrition, such as job satisfaction, tenure, and promotion opportunities, offering actionable insights for retention strategies. Additionally, by predicting probabilities rather than binary outcomes, this study aims to make more detailed decisions about employee retention. This research provides valuable tools for financial institutions to mitigate the risk of turnover, retain critical talent, and ensure operational continuity.

Granular material is one of the most common in nature. Recently, there has been a significant amount of interest in the granular materials, such as powders or sand. It is challenging to describe the motion of such kind of macroscopic size matter, because it behaves like solid, fluid or gas. Size division, pattern formation, avalanches, packing and convection - these are just a few examples from a wide range of observed phenomena that occur during the motion process of granular matter. Most of these processes are based by flow and no wonder that much effort has been devoted to obtain a hydrodynamic description in which granular materials are treated as a continuous medium. During the research of vertically shaken granular medium motion in an opened container it was found that experimental and numerical results are explained by hydrodynamic theory. This paper investigates the motion of a granular matter for a shallow, vertically shaken bed. We assume the Leidenfrost state as initial and the matter resembles a fluid heated up from below.A one-dimensional isothermal and a non-isothermal problem of granular material motion,simulatedby a hydrodynamic model are considered, and the material is assumed to be a continuous medium. The local temporal solvability of isothermal and non-isothermal initial boundary-value problem in Sobolev’s spaces is proved. This work presents a numerical study of the one-dimensional model of granular medium flow. The feature of this model is consideration of the Navier-Stokes equations accounting an interpolation form of VanderWaals constitutive equation for pressure. A finite-difference approximation for numerical solution is proposed.

This bibliometric study analysed breast cancer research trends and outputs from 2014 to 1 2023, utilising data from the Scopus database. The primary objectives include analysing publication 2 growth, citation metrics, document type distribution, leading countries, preferred journals and 3 authorship patterns. The study reveals a significant increase in breast cancer research publications, 4 with a total of 12,073 documents and 216,769 citations over the ten-year period. The United States 5 leads in publication output and citation impact, followed by China and Japan. Articles are the 6 predominant document type for total 73.4% of publications, while reviews and book chapters also 7 contribute notably. The most preferred journals for publishing breast cancer research include Breast 8 Cancer Research and Treatment, Clinical Breast Cancer, and Breast Cancer Research. Authorship 9 patterns show a trend towards multi-authored papers, with a substantial number of papers having 10 more than five authors. The study underscores the global collaborative effort in advancing breast 11 cancer research and highlights key areas for future exploration.

This study combines two methodologies—key indicators from the Sustainable Livelihoods Framework (SLF) and the Sustainability Assessment of Food and Agriculture Systems (SAFA) approach—to evaluate sustainability among 330 producers from three associations working within the recently recognized Amazonian Chakra system, designated as a Globally Important Agricultural Heritage System (GIAHS). The SAFA framework's four dimensions—Good Governance, Environmental Integrity, Economic Resilience, and Social Well-being—were used to assess sustainability, while the SLF considered key capitals such as financial, natural, and human capitals as critical for understanding livelihood outcomes. The discriminant analysis revealed significant differences across the associations, with Kallari and Wiñak performing better in financial management, environmental practices, and governance compared to Tsatsayaku, which exhibited weaker outcomes in these domains. Key indicators such as chakra income, price determination, and civic responsibility were the most effective in distinguishing the groups. The income analysis further highlights that Tsatsayaku reported the highest total income but relies heavily on non-Chakra sources, while Kallari and Wiñak showed stronger reliance on Chakra income, which aligns with their more sustainable agricultural practices. Per-capita income was higher for Tsatsayaku, but extreme poverty levels remained similar across all associations, underscoring the need for targeted financial interventions. Policy recommendations include promoting access to financial resources and strengthening participatory governance models to enhance sustainability outcomes across associations. For future research, combining the SAFA and SLF provides a comprehensive and robust methodology for assessing sustainability in agricultural systems, enabling a deeper understanding of the interactions between social, economic, and environmental factors in diverse contexts.

Early detection of cervical cancer is the need of the hour to stop the fatality from this disease. There have been various CAD approaches in the past that promise to detect cervical cancer in an early stage, each of them having some constraints.This study proposes a novel ensemble deep learning model, VLR (variable learning rate), aimed at enhancing the accuracy of cervical cancer classification. The model architecture integrates VGG16, Logistic Regression, and ResNet50, combining their strengths in an offbeat ensemble design. VLR learns in two ways: firstly, by dynamic weights from three base models, each of them trained separately; secondly, by attention mechanisms used in the dense layer of the base models. Hyperparameter tuning is applied to further reduce loss, fine tune the model’s performance, and maximize classification accuracy. We performed K-fold cross-validation on VLR to evaluate any improvements in metric values resulting from hyperparameter fine tuning. We have also validated our model on images captured in three different solutions and on a secondary dataset. Our proposed VLR model outperformed existing methods in cervical cancer classification, achieving a remarkable training accuracy of 99.95% and a testing accuracy of 99.89%.

To date, SARS Cov-2 virus has caused more than 775 million cases worldwide and led to 7 million deaths. The virus enters cells with the aid of the ACE2 receptor located in the airway epithelium, but also in endothelial cells lining the inner walls of vessels. Endothelial damage results in impaired blood flow and gas exchange. Statins have been shown to have a pleiotropic effects on the vascular epithelium. Aim of the study: Assessment of the efficacy and safety of statin therapy in patients with COVID-19. Methods: Two hundred and one COVID-19 patients hospitalized at the Jerzy Gromkowski Regional Specialist Hospital between March 2020 and December 2021 (i.e. during the period dominated by Alpha, Beta, Gamma and Delta variants). Patients were divided into three groups: (I) patients treated with statins prior to the admission to the hospital; (II) patients started on statins after admission due to Covid-19; (III) control patients with Covid-19, not treated with statins either prior to or during hospitalization. Met Statistica 13.1 calculations were used in the paper. Shapiro-Wilk, Kruskal-Wallis and ANOVA tests were also performed. Results: Out of the 201 patients total, group I comprised 66 patients with a mean age of 66.2 years; group II comprised 33 patients with a mean age of 75.3 years; and the control group comprised 97 patients with a mean age of 61.1 years. The groups characteristics did not show significant differences in terms of gender, place of hospitalization, percentage of Covid-19 vaccinations, number of convalescents. Death was observed in: 12% of patients in group I, 6% of patients in group II, and 6% of patients in group III. Body Mass Index (BMI) in group I was 31.3: a value significantly higher than the control group’s 28.3, (p<0.05). The severity of Covid-19 assessed on admission in group I – 4.09 – was statistically higher than in the control group 3.52 (p<0.05). The number of pulmonary embolism incidents did not differ between groups. Conclusions: During the period dominated by Alpha, Beta, Gamma and then Delta variants, we found no statistically significant positive or negative effects of statin therapy on the duration of hospitalization, number of complications or percentage of deaths between the two studied groups of patients: those who received statins prior to hospitalization, and those who received statins during hospitalization.

Pichia pastoris is extensively employed as a host for expressing foreign proteins, and its secretion system is especially advantageous for efficient protein purification. Ulp1 is essential for the cell cycle. In Saccharomyces cerevisiae, the absence of Ulp1 leads to G2/M cell cycle arrest. Similarly, in Pichia pastoris, we also observed G2 phase stalling in Ulp1 knockout cells. RNA-seq data revealed significant changes in seven genes, including INO1. Interestingly, overexpressing INO1 in Ulp1 knockout cells restored cell proliferation, suggesting that Ulp1 regulates cell proliferation through INO1. However, adding extra inositol to Ulp1 knockout cells was not able to restore cell prolifera-tion, indicating that the enzyme activity of INO1 is not essential for cell proliferation. Our data provide new insights into Ulp1 functions in the cell cycle and raise new questions about yeast cell cycle regulation.

Background and Objectives: A degenerative joint disease that primarily affects the elderly, osteoarthritis (OA) causes pain, decreased mobility, and a lower quality of life. The effectiveness of GerovitalH3, a biotrophic medication created by Ana Aslan, in reducing pain and enhancing function in older people with osteoarthritis in the knee and hip is assessed in this study. Materials and Methods: Two groups of 201 patients aged 65 and older participated in a randomized, case-control clinical trial. One group received physical therapy and GerovitalH3 periarticular injections, while the other group received just physical therapy. In addition to functional evaluations using the Lequesne Index, Activities of Daily Living (ADL), and Instrumental ADL (IADL) scores, pain was assessed using a Visual Analogue Scale (VAS). Results: The GerovitalH3 group showed a substantial decrease in pain (p<0.001) and an improvement in daily activities (p<0.001) when compared to the control group. However, there was no significant difference in walking scores (p = 0.171). There were no significant adverse effects noted. GerovitalH3 did not outperform physical therapy for reducing depression, even though both groups displayed some improvement in this area. Conclusions: This study opens a new possibility for periarticular injections of Gerovital H3 treatment combined with physical therapy, which may represent a safe and effective non-surgical option for elderly individuals struggling with OA pain and functional limitations. The findings of this study reinforce the need for further research, particularly randomized controlled trials with larger sample sizes and longer follow-up periods.

Background: Nanotechnology has emerged as a promising field of study, aiming to revolutionize healthcare through the innovative development of drugs, diagnostic tools, and medical devices. As a result, healthcare professionals in training are constantly faced with the challenge of understanding and applying these emerging technologies. The objective of this study is to determine the factors to consider for including the teaching of nanotechnological tools in medical specialty postgraduate programs. Methods: A study based on the Nominal Group Technique (NGT) was conducted to identify the factors that promote and hinder the implementation of nanotechnology in certain postgraduate programs where nanotechnology is employed, such as Internal Medicine, Critical Care Medicine, Family Medicine, and Clinical Pharmacology at the School of Medicine of Universidad de La Sabana. A framework analysis was used to analyze the collected data. Results: Based on the two research questions, several aspects were identified for the inclusion of nanotechnology in the medical practice of specialties. Key challenges include lack of knowledge and resource availability, misinformation, and lack of knowledge, as well as paradigmatic analysis as the main obstacles to the use of nanotechnology. Conclusions: The findings provide a first-time study on nanotechnology curricula within medical specialty programs in Colombia, with potential extrapolation to similar situations in other medical schools.

The species and bio-availability of phosphorus (P) in primary, secondary and digested sludge were fractionated and further analyzed in this study. Results showed that inorganic P (IP) was the primary P fraction in the secondary sludge and digested sludge, in which non-apatite IP (NAIP) amounted to 91.6% and 69.3% of IP, respectively. Organic P (OP), accounting for about 71.7% of total P (TP), was the dominant P composition in primary sludge. The content of bio-available P was about 9.7, 43.4, 29.8 mg-P/g-TS in primary sludge, secondary sludge and digested sludge, respectively, suggesting secondary sludge is the optimal choice when land application of sewage sludge is taken into consideration, followed by digested sludge and primary sludge. Polyphosphate and orthophosphate, comprising approximately 54.3% and 89.2% of TP, was the dominant P species in the secondary sludge and digested sludge, respectively. Monoester-P (54.6% of TP in extract) and diester- P (24.1%) were identified as OP species in primary sludge by Phosphorus-31 nuclear magnetic resonance (31PNMR). The present results would be helpful for P recovery and recycle from sewage sludge in wastewater treatment plant.

We conducted a comparative study on the development of two synthetic methods. The solvent-free synthesis is a green chemistry method developed in a bid to ameliorate environmental adverse effects of the conventional solvent-based synthesis. The synthesis of novel dichloro and polymethoxy p-nitrophenylhydrazones through solvent free technique gave moderate to high yields which were however lower than those of the solvent-based method. The established solvent-free approach has several benefits, including universality and simplicity of the approach, catalyst-free conditions, non-use of an organic solvent, quick reaction time, fast and efficient workup, and un-solvated pure products in moderate to high yields.

The insertion of the Amazon into the global commodities market requires ensuring the rational use of resources to meet market and political-social demands, such as the UN 2030 Agenda. Therefore, responsible production practices, given the current demand for sustainable use of land and its re-sources, are essential. Thus, the objective of this study was to identify opportunities and challenges linked to the implementation and consolidation of sustainable production systems in the Amazon through a systematic literature review. To this end, articles were prospected in four databases (Science Direct, SpringerLink, Scopus and Wiley) covering the period from 2004 to 2024. A total of 5,385 articles were evaluated, and after the selection stages, only 39 were included. A low distri-bution of studies among states in the Brazilian Amazon was observed, with a peak in studies star-ting in 2015. The studies developed mostly addressed agroforestry systems and forest management. Although there are sustainable production systems and practices, research and public policies need to be promoted to help the different actors involved in agricultural production in the Amazon, generating income and quality of life.

The aim of our research was to evaluate and analyze serum 25(OH) vitamin D and parathyroid hormone (PTH) levels to investigate whether vitamin D deficiency serves as a risk factor for an increased incidence of acute respiratory infections (ARI) in children. Serum PTH levels were used as an indicator of vitamin D sufficiency, as normal PTH levels require an optimal concentration of 25(OH) vitamin D. The study included 129 children, divided into five subgroups: children with acute bronchopneumonia (n=42), acute laryngotracheitis (n=7), acute bronchiolitis (n=32), acute bronchitis (n=18), and a control group (n=30). No statistically significant differences in 25(OH)D levels were observed between the overall population of children with ARI and the control group (p=0.073). However, significant differences in 25(OH)D levels were identified between the control group and children with bronchopneumonia, acute bronchitis, and laryngotracheitis (p<0.01, p<0.05). Vitamin D insufficiency was found in 28.3% of children with ARIs and 10% in the healthy group. Sufficient levels were present in 60% of healthy children and 48.5% of those with ARIs. Deficiency was observed in 4% of ARI patients and 3.3% of the control group. Regarding PTH levels, statistical significance was found between the control group and the acute bronchiolitis group, due to the high percentage of children with hypervitaminosis in this subgroup. These results highlight the crucial role of vitamin D in the onset and progression of acute respiratory tract infections in children, emphasizing its impact on their overall respiratory health.

Background: RO and ChRCC are kidney tumours with overlapping characteristics, making differentiation between them challenging. Objectives: The objective of this research is to create a radiogenomics map by correlating radiomic features to molecular phenotypes in ChRCC and RO, using resection as the gold standard. Methods: Fourteen patients (6 RO and 8 ChRCC) were included in the study. A total of 1,875 radiomic features were extracted from CT scans, alongside 632 cytobands containing 16,303 genes from the genomic data. Results: Feature selection algorithms applied to the radiomic features resulted in 13 key features. From the genomic data, 24 cytobands highly correlated with histology were selected and cross-correlated with the radiomic features. The analysis identified four radiomic features that were strongly associated with seven genomic features. Conclusion: These findings demonstrate the potential of integrating radiomic and genomic data to enhance the differential diagnosis of RO and ChRCC, paving the way for more precise and non-invasive diagnostic tools in clinical practice.

This paper presents an approach to assess and improve the cybersecurity infras- tructure of developing countries. We have highlighted and addressed the critical gaps through a hybrid approach encompassing SWOT analysis, benchmarking using Data Envelopment Analysis (DEA) and, Root Cause Analysis (RCA). This approach has provided a strong basis for evaluating cybersecurity performance by combining qualitative insights with quantitative metrics. As a case study, we have compared an underdeveloped country’s (Pakistan) cybersecurity pos- ture to five highly developed countries (Lithuania, Estonia, Singapore, Spain,and Norway). Our analysis has identified cybersecurity shortcomings and pro- vided actionable recommendations within a flexible framework, applicable for all developing countries to identify and address vulnerabilities, and align their cybersecurity infrastructure with international standards.

The increasing energy consumption and industrial activities that release carbon dioxide (CO2) emissions into the atmosphere have become one of the most serious environmental issues of today. This article discusses the current status in Azerbaijan regarding the development of effective approaches to reduce carbon emissions and ensure sustainable development, and it proposes relevant strategies for managing the carbon footprint. By exploring the interrelationship between the economy and the environment, it aims to contribute to the formation of more effective policies for managing CO2 emissions in Azerbaijan. According to the results of the econometric model established within the research for the period of 1990-2023, as the Azerbaijan economy grows, per capita CO2 emissions tend to increase, which can be linked to rising industrial activity, energy consumption, and other factors driving economic growth. The presence of a positive long-term relationship between population growth and per capita CO2 emissions can be attributed to higher overall energy consumption, increased demand for goods and services, and rising transportation needs. The strong correlation between economic growth and CO2 emissions suggests that it may be too early to assert the validity of the Kuznets curve for Azerbaijan economy as a developing country.

Fluctuations in kynurenic acid (KYNA) and brain-derived neurotrophic factor (BDNF) levels in the brain reflect its neurological status. The aim of the study was to investigate the effect of transiently elevated KYNA concentration in the cerebroventricular circulation on the expression of BDNF and its high-affinity tropomyosin-related kinase receptor B (TrkB) in specific structures of the sheep brain. Intracerebroventricularly cannulated anestrous sheep were subjected to a series of four 30-min infusions of KYNA: 4×5 μg/60 μL/30 min (KYNA20, n=6) and 4×25 μg/60 μL/30 min (KYNA100, n=6) or a control infusion (n=6), at 30-min intervals. Sections of the hippocampal CA3 field, amygdala (AMG), prefrontal cortex (PCx), and the hypothalamic medial-basal (MBH) and preoptic (POA) areas were dissected from the brain immediately after the experiment. The highest concentration of BDNF protein was found in the CA3 field (P&lt;0.01), which was 8-fold higher than in the AMG and 12-fold higher than that in the PCx (MBH and POA were not analyzed). The most pronounced BDNF mRNA expression was observed in the MBH followed by the PCx, POA, AMG and CA3, while the highest abundance of TrkB mRNA was recorded in the AMG followed by the MBH, PCx, CA3 and POA. KYNA increased (P&lt;0.05-P&lt;0.01) BDNF protein levels and the expression of its gene in the brain structures examined, with the effect varying by dose and brain region. KYNA, particularly at the KYNA100 dose, also increased (P&lt;0.01) TrkB gene expression, except for the AMG, where the lower KYNA20 dose was more effective (P&lt;0.01). These findings suggest a positive relationships between KYNA levels in the cerebroventricular circulation and BDNF-TrkB expression in specific brain regions in a sheep model. This indicates that a transient increase in CSF KYNA concentration can potentially restore BDNF production, whose deficiency underlies numerous neurological disorders.

Diospyros kaki, the most widely cultivated species of persimmon, has been long used in traditional medicine since its leaves extracts contain high amounts of flavonoids and terpenoids, endowed with potential antioxidant, anti-inflammatory, anticancer, antidiabetic and antimicrobial effects. Re-cently, many in vitro and in vivo studies have assessed different potential health benefits of per-simmon leaves; however, its anticancer activity towards colorectal cancer (CRC), the second deadliest cancer in Western countries, has not been investigated in depth. Since CRC current therapies are associated with serious side effects and show no efficacy towards patients carrying RAS/BRAF mutations, the search for new and more effective therapies has turned to plant extracts, which could help reduce conventional drugs dosages and toxicity. The effect of Diospyros kaki al-coholic extract has been investigated on E705 CRC cell line, representative of most CRC patients, and on SW480 cells, carrying a KRAS activating mutation. This extract is effective in reducing tumor cells viability, without affecting the healthy mucosa cell line CCD 841, and it triggers apoptosis in CRC cells, by disrupting mitochondrial functionality and increasing oxidative stress.

Pre-transport management activities can cause stress, injuries, and mortality in poultry. This study aimed to gather information about the current pre-transport practices (selection of unfit chickens, catching preparations, catching, and crating) for spent hens and broilers by questioning Flemish poultry farmers. The results showed that catching preparations such as an extra selection of chickens unfit for transport was performed by a minority of the poultry farmers, and that layer farmers were less in line with the EU-legislation for water and feed withdrawal than broiler farmers. All birds were caught inverted except for one broiler farmer who used mechanical catching (not yet common in Flanders). Additionally, mechanical catching may involve extra costs, increased biosecurity risks, and specific recommendations for the stable (height and width). The broiler farmers preferred mechanical catching for broiler catchers' well-being, while upright catching was considered better for animal welfare than catching more than three chickens by one/two legs, mechanically, or by wings. Awareness of the need to perform an extra selection by the poultry farmers before catching is required. Preparations like closing areas under the aviary system and removing litter (layers) can further streamline the process and reduce animal suffering.

This stability analysis method is simply represented and understood on a Bode plot of two impedances without complex equations. The external impedance of the charging system is properly quantified and designed based on the stability criteria by analyzing.

Arbutus unedo (strawberry tree) is a small Mediterranean tree capable of vigorous regrowth after disturbances like fire. Traditionally used for biomass fuel, its bark and branches hold potential for higher-value products through ecovalorisation into liquid mixtures that could replace petro-leum-based materials. This study aimed to explore the chemical composition of various compo-nents of Arbutus unedo and to produce a liquefied material from its internal (IB) and external bark (EB). Chemical compositions of internal and external bark were determined using TAPPI standards including ash, extractive content, lignin, and cellulose. Metal cations were analyzed by ICP. Liquefaction of bark was optimized in a PARR reactor, evaluating factors such as particle size, temperature, and time and the best polyols were monitored by FTIR-ATR. Polyurethane foams were made with internal and external bark liquefied materials by polymerization with isocyanate, a catalyst and water as blowing agent. Results showed that EB has a higher extractive and lignin content, while IB contains more cellu-lose. Liquefaction yields were higher for IB (74%) than EB (68%), with IB yielding polyols that produced stronger and more resilient foams. Mechanical properties of the foams were influenced by the NCO/OH ratio and catalyst levels. Overall, the internal bark demonstrated superior performance for foam production, highlighting its potential as an eco-friendly alternative to petroleum-derived materials.

Introduction: Leptin and ghrelin are two hormones that play a role in weight homeostasis. Leptin, which is produced primarily by adipocytes and is dependent on body fat mass, suppresses appetite and increases energy expenditure. Conversely, ghrelin is the “hunger hormone”, it stimulates appetite and promotes fat storage. Bariatric surgery significantly alters the levels and activity of these hormones, contributing to weight loss and metabolic improvements. Clarifying the interplay between bariatric surgery, weight loss, physical exercise, leptin, and ghrelin is essential for developing comprehensive strategies for optimizing long-term outcomes for candidates for bariatric surgery, especially sarcopenic patients. Methods: This was a randomized controlled study with two groups (n=22). The patients in both groups have obesity and sarcopenia. A Roux-en-Ygastric bypass (RYGB) procedure was performed in all patients. The intervention group participated in a structured exercise program three times per week beginning one month after surgery and lasting 16 weeks. Patient assessment was performed before surgery (baseline) and after completion of the exercise program. The control group received the usual standard of care and was assessed similarly. Results: After surgery, weight, BMI and lean mass decreased significantly in both groups from baseline to the second assessment. Leptin was not significantly different from baseline to the second assessment in the physical exercise group but was significantly lower in the control group (p=0.05). Ghrelin increased over time in both groups, but the differences were not significant. When we associated leptin (the dependent variable) with weight (the independent variable), we found that lower weight was associated with lower leptin levels. A similar relationship was also observed between leptin and sarcopenia parameters (muscle strength and mass), as well as with bone health parameters (bone mineral density and t-score). Higher ghrelin levels were significantly associated with higher t-scores and z-score (p<0.05). Conclusion: Exercise has been shown to have a significant effect on leptin and ghrelin levels after bariatric surgery. By incorporating regular physical activity into their lifestyle, bariatric patients can optimize their weight loss outcomes and improve their overall health. After the physical exercise protocol, patients in the intervention group revealed more established leptin levels, which may indicate a protected pattern concerning decreased leptin levels. An unfavorable profile was evidenced, according to which greater weight loss, sarcopenia, and osteoporosis were associated with lower leptin levels.

Among the theoretical problems with the prevailing theory of cosmology, Lambda Cold Dark Matter (λCDM), the most serious appears to be the twofold problem with the cosmological constant lambda: Dark Energy and Hubble Tension. Despite a two-decade search for systematic errors in astrometry the problems have not been resolved. This paper posits a potential source of error that may have affected astrometry related to the current and past measurements of lambda.

Differential beamforming has attracted much research since it can utilize the array with small aperture size to form frequency-invariant beampatterns and achieve high directional gains. It has recently been applied to the linear loudspeaker array to produce a broadside frequency-invariant radiation pattern. However, designing steerable frequency-invariant beampatterns for the linear loudspeaker array has yet to be explored. This paper proposes a method to design the steerable differential beamformer with the linear loudspeaker array. We first determine the target differential beampatterns according to the desired direction, the main lobe width, and the beampattern order. Then, we transform the target beampattern into the modal domain for representation. The Jacobi-Anger expansion is subsequently used to design the beamformer so that the resulting beam pattern matches the target differential beam pattern. Furthermore, based on the criterion of minimizing the mean square error between the synthesized beam pattern and the ideal one, a multi-constraint optimization problem is formulated to calculate the optimal desired weighting vector. Simulations and experimental results show that the proposed method can achieve steerable frequency-invariant beamforming over 300 Hz – 4 kHz.

N-(diisopropylphosphanyl)benzamide, PhC(O)NHPiPr2, has been synthesized in good yield following two alternative procedures that employ benzamide as the starting material. The first one is a two-step preparation, in which N-(trimetilsilyl)benzamide is reacted with PiPr2Cl, to give the title compound in good yield, whereas the second one is a straightforward synthesis which converts benzamide into N-(diisopropylphosphanyl)benzamide by reaction with PiPr2Cl in the presence of N,N-dimethylpyridin-4-amine (DMAP) and triethylamine. NMR spectroscopy and X-ray diffraction analyses have been performed to characterize the new compound and elucidate its molecular structure in the solid state. N-(diisopropylphosphanyl)benzamide adds to the limited family of amido-substituted phosphines, RC(O)NHPR’2, which can be classified as bidentate hybrid P,O-ligands, both in their neutral and anionic forms, the latter achievable by deprotonation of the NH group.

In the bioprinting process, controlling the motion of bioprinters involves a computer-aided design (CAD) model, converting that model into g-code, and transmitting the motion commands to the bioprinters. The g-code file contains information about the motion of the axes and can be generated using various software. However, a challenge arises when using g-code between different bioprinters. Therefore, the objective of this study was to propose a reliable method for analyzing the differences in 3D bioprinting devices by parameterizing a crucial variable for extrusion bioprinting: the E-value. Four bioprinters from three different manufacturers were used to investigate the extrusion behavior when subjected to the same E-value.

Background: COVID-19 mainly affects the respiratory system, although its manifestations are multisystemic. Increasingly, complications presented after the acute phase are still being rec-ognized and are associated with impaired functional status and health-related quality of life (HRQoL). The objective was assess the functional status and HRQoL of patients with post-COVID-19. Methods: This was a cross-sectional study involving individuals affected by COVID-19 who had persistent symptoms for one month after the acute phase of the disease. HRQoL was verified through the Short Form Health Survey 36 (SF-36) and, functional status was assessed using the six-minute walk test (6MWT), the Fatigue Severity Scale (FSS), the Med-ical Research Council (MRC) Dyspnea Scale and, the Post-COVID-19 Functional Status Scale (PCFS). Results: Were included 123 patients, 73 (59.35%) were male, with a mean age of 49.17±13.48 years and a body mass index of 31.02±6.56 stratified into three groups, not recov-ered group (NRG=23), ward recovered group (WHG=60), and intensive care unit group (ICUG=40). The main symptoms were muscle weakness (74.17%) and dyspnea (68.33%). In rela-tion to the distance covered in the 6MWT, the GNR group walked 12.83% below the predicted values, GNR 20.21% and the UGCI 28.82%, respectively. The MRC dyspnea scale had a mean value of less than 3 and the FSS scale had a mean value over 4, indicating considerable fatigue. In the PCFS scale, a significant difference was observed (p>0.0005); while in the SF-36, all HRQoL domains were compromised. Conclusion: Post-COVID-19 patients involved in this study showed a significant decline in functional status and an impairment of HRQoL.

Human-Computer Interaction (HCI) has evolved significantly with advances in Artificial Intelligence (AI) and Computer Vision (CV), paving the way for more intelligent and adaptive user interfaces. This paper explores the design and implementation of user interfaces that leverage AI and CV to create more intuitive, responsive, and personalized experiences. By integrating techniques such as facial recognition, gesture control, and eye tracking, interfaces can adapt in real-time to users’ actions and intentions, thus enhancing accessibility, efficiency, and engagement across various applications, from healthcare to gaming. The study reviews current advancements and challenges in using AI and CV for HCI, including data privacy, model interpretability, and computational efficiency. Experimental results demonstrate the potential of these technologies to improve interaction quality and user satisfaction. This work aims to contribute to the growing field of intelligent HCI design, offering insights into practical implementations and future research directions in AI-driven interface development.

Tissue engineering is an interdisciplinary field that combines methods, materials, and biological molecules to fabricate newly formed tissues to replace or restore functional organs. Biomaterials-based scaffolds play a vital role in developing new tissue by interacting with human cells. Tissue Engineering scaffolds with ideal characteristics, namely, nontoxicity, biodegradability, and appropriate mechanical and surface properties, are vital for tissue regeneration applications. Although commonly utilized biomaterials can provide physical and chemical properties needed for tissue regeneration, inadequate biomimetic properties, as well as insufficient interactions of cells-scaffolds interaction, still need to be improved for the application of tissue engineering in vivo. Consequently, developing innovative biomaterials-based stimulus-responsive 3D scaffolds that can enhance the mediators of cell adhesion and cellular functioning and that can form functional tissues by providing structural integrity within an appropriate time is much needed. It is possible to achieve some essential features using a single material, so combining two or more materials may fulfill the requirements. In order to achieve a proper scaffold design, a suitable fabrication technique and combination of biomaterials with controlled micro or nanostructures are needed to achieve the proper biological responses. This review highlights the natural polymers, smart materials, and recent advanced techniques currently used to create emerging scaffolds for tissue regeneration applications.

Solid propellants have significant applications in aerospace, and improving their combustion performance has become a hot research topic in recent years. Carbon black (CB) has been widely used in the field of catalytic pyrolysis due to its low cost, controllable morphology, and ease of modification. Herein, we first investigates the structure-activity relationship between the physicochemical properties of nine types of CB with a particle size range of 1-15 μm and a mass fraction of 5%, including oil absorption value, compression oil absorption value, and oxygen content, and the catalytic pyrolysis of ammonium perchlorate (AP), concluding that the function relationship between oil absorption value and high-temperature peak is Y1=1032.67-9.618x+0.038x2, the function relationship between compression oil absorption value and high-temperature peak is Y2=145.537+62.365ln(x), and the function relationship between oxygen content and high-temperature peak is Y3=e(6.085-0.02/x). Based on these, we further uses coal tar, which is abundant in sources, as the raw material to prepare five types of coal-based CB marked as CB1-CB5 at pyrolysis temperatures of 1000~1800 ℃. The relative error between the actual peak value and the predicted value of the CB/AP composite particles is less than 5%, proving that the peak temperature model of CB/AP composite particles can guide actual production. This study contributes to promoting CB application in improving the catalytic pyrolysis performance of ammonium perchlorate and enhancing the high added value utilization of coal-derived products.

Generative adversarial networks consisting of two parts, generator and discriminator, have obtained acceptable results in classification, prediction and generation of new samples in the discussion of 4G, 5G and 6G. In this article, the aim is to review a comprehensive study in relation to these networks. At the beginning of this research, different topics such as network training, network error checking and types of GAN's are investigated. In the following, the applications of GAN will be discussed separately.

The gut, often referred to as the "second brain," has significant contributions in the maintaining of the good bacteria contribute enormous role such as digestion, produce essential vitamins, support the immune system, and protect against harmful bacteria. The beneficial flora including Akkermansia muciniphila, Adlercreutzia equolifasciens, Barnesiella, Christensenella minuta, and Oxalobacter formigenes, along with their derived bioactive metabolites emerged as a key player in maintaining host metabolic and immune health. Dietary choices such as blending of prebiotic, fermented, symbiotic, anti-inflammatory foods, and secondary metabolites from a wide variety of plants and fruits promotes the diversity, composition, and stability of beneficial intestinal microbes. The colourful plant foods rich in phytochemicals bioactive compounds such as carotenoids, flavonoids, polyphenols, alkaloids, anthocyanins, and capsaicin offer a wide array of unique properties such as analgesics, antioxidants, anti-inflammatory, antimicrobials effect and promoting the abundance of beneficial gut bacteria and their bioactive metabolites confer numerous health-promoting effects. Here, we present knowledge about most beneficial gut bacteria and their derived metabolites in terms of their sources and health benefits. Finally, we discuss best foods that skew towards promoting healthy intestinal microbes.

This article presents a method for detecting P, QRS, T, and U waves in electrocardiogram (ECG) signals through advanced signal processing techniques, including a Butterworth bandpass filter and peak finding algo- rithms. The results are evaluated against the voltage ranges recommended in the literature, underscoring the importance of accurate wave detection for the diagnosis of various cardiac conditions.

Additive Manufacturing (AM) methods are increasingly beign abopted in the industry as an alternative for mass production. In particular, Fused Deposition Modeling (FDM) technology is leading the way in this field. However, the adhesion of layers in products produced using FDM technology is an important issue. These products are particularly vulnerable to forces acting parallel to the layers and specially to impact strength. This study aims to optimize the impact strength against loads acting parallel to the layers (ZX orientation) of PA6, one of the most widely used materials in the industry. This orientation is critical in term of mechanical properties, and the mechanical characteristics are significantly lower compared to other orientation. In this study, filaments containing pure PA6 with 15% short carbon fiber and 30% glass fiber were utilized. Additionally, printing temperature, layer thickness and heat treatment duration were used as independent variables. An L9 orthogonal array was employed in this study, and each experiment was repeated three times to conduct impact strength tests. Characterization, Taguchi optimization, a factor analyses were performed, followed by fracture surface characterization by SEM. As a result, the highest impact strength was achieved with pure PA6 at 8.9 kJ/m2, followed by PA6 GF30 at 8.1 kJ/m2 and the lowest impact strength was obtained with PA6 CF15 at 6.258 kJ/m2. When compared to the literature and manufacturer datasheets, it was concluded that the impact strength values have significantly increased, and the chosen experimental factors and their levels, particularly nozzle temperature, were effective.

For Sir Ronald Fisher, it is important to consistently obtain significant p-values to support an experimental hypothesis. So, replicating experiments to obtain independent p-values is a legitimate and desirable research practice. Several simple statistics have been proposed to meta-analyze p-values, all assuming that they are genuine, i.e. observations from independent standard Uniform random variables. But, as publication bias favors the studies that report "significant" p-values, when a p&gt;0.05 is obtained for the outcome of an experiment, some researchers will "fall into temptation" and decide to replicate the experiment in the hope of getting a smaller second p-value, ideally a significant one. Consequently, if the smallest of two p-values is reported, this is a Beta(1,2) distributed "fake" p-value, not a uniformly distributed genuine p-value. This is an unacceptable scientific research practice, and moreover the detection of fake p-values is unpractical. Even when it is possible, the analytic results to accommodate their existence in combined tests are cumbersome. For an informed decision, inclusive when the presence of fake p-values in a sample of p-values to be meta-analyzed is probable, tables with simulated critical values for the usual combined testing are supplied. This will also allow comparisons to be made between several combined tests.

The global malaria community has picked up the theme of malaria elimination in greater than 90 % of the world’s population in the next decade. The recent reports of P. vivax in all sub-Saharan Africa, including Duffy negative individuals, threaten the efforts to achieve elimination. This is not only in view of strategies that are tailored only to P. falciparum elimination, but also due to currently revealed biological characteristics of P. vivax concerning the relapse patterns of hypnozoites and conservation of a large biomass at cryptic sites in the bone marrow and spleen. A typical scenario has been observed in Botswana from the period between 2008 to 2018, which palpably projects how P. vivax could endanger efforts at malaria elimination where the two parasites co-exist. The need for the global malaria community, NMPs, funding agencies and relevant stakeholders to engage in a forum to discuss and recommend clear pathways for sub-Saharan Africa regarding malaria elimination including P. vivax, is warranted.

Academic and corporate research has been focusing on analyzing stock performances, financial markets, and investment strategies for decades. According to Lynch and Rothchild (1989), certain investments can be described as plays. In this work, the authors use the term for investments in value stocks, spin-offs, and turnarounds to analyze the long-term stock performance and risk-adjusted excess returns of up to five years for those stocks. Additionally, stocks with a supe-rior return performance are identified within an investment play based on low P/E and P/B mul-tiples. The study finds that value stocks, spin-offs, and turnarounds outperform the S&P 500 on average on a one-, three- and five-year investment horizon. The analysis of the three investment plays confirms earlier studies that investment plays constitute a profitable investment opportunity. Moreover, the research exemplifies that private investors could achieve an excess return (alpha) through a passive buy-and-hold investment strategy. Overall, the analysis provides a deeper in-sight into the long-term performance of value stocks, spin-offs, and turnarounds.

Three-dimensional (3D) printing technology, also known as additive manufacturing (AM), has emerged as an attractive state-of-the-art tool for precisely fabricating functional materials with complex geometries, championing several advancements in tissue engineering, regenerative medicine, and therapeutics. However, this technology has an untapped potential for biotechnological applications, such as sensor and biosensor development. By exploring these avenues, the scope of 3D printing technology can be expanded and pave the way for groundbreaking innovations in the biotechnology field. Indeed, new printing materials and printers would offer new possibilities for seamlessly incorporating biological functionalities within the growing 3D scaffolds. Herein, we review the extrusion-based 3D printing modalities emphasizing biosensor applications. We highlighted the application of natural, synthetic, and composite biomaterials as 3D-printed soft hydrogels. Emphasis was placed on the approach by which the sensing molecules were introduced during the fabrication process. Finally, the future perspective was provided.

Synthesis of heterodinuclear 3d transition metal complexes in which two metal ions are introduced in equivalent coordination sites of a ligand is quite uncommon. We have previously shown that the application of the cis-trans isomerization of the oxamido group was able to furnish such a possibility. In the present paper we demonstrate that this synthetic pathway, relying on the possibility of changing the conformation (cis vs trans) of the oxamido group, can be extended to other ligands. Although we have not been able to structurally characterize these complexes, EPR and magnetic data do confirm the efficiency of this reaction pathway. We also demonstrate that the cis-trans isomerization of the oxamido group is not due to a particular property of the ion involved in the reaction. In fact, isomerization is governed by the basicity of the reaction medium. According to the reaction condition, it is possible to favor or not this phenomenon, and to increase the accessibility to a larger number of novel genuine complexes. But the oxophilic character of the lanthanide ions impedes this isomerization in 3d-4f complexes. The very weak magnetic interactions observed in these Cu-Gd complexes can be explained thanks to spin polarization.

Based on three-dimensional optical proximity correction (3D OPC), recent advancements in 3D lithography have enabled the high-fidelity customization of 3D micro-optical elements. However, micron-to-millimeter scale structures represented by Fresnel lens design bring more stringent requirements for 3D OPC, which poses significant challenges to the accuracy of models and the efficiency of algorithms. Thus, a lithographic model based on optical imaging and photo-chemical reaction curve is developed in this paper, and a sub-domain division method with a statistics principle is proposed to improve the efficiency and accuracy of 3D OPC. Both the simulation and the experimental results showed the superiority of the proposed 3D OPC method in the fabrication of the Fresnel lenses. The computation memory requirements of the 3D OPC are reduced to below 1 %, and the profile error of the fabricated Fresnel lens reduced 79.98%. Applying the Fresnel lenses to an imaging system, the average peak signal to noise ratio (PSNR) of the image increased by 18.92 %, and the average contrast of the image enhanced by 36 %. We believe the proposed 3D OPC method can be extended to the fabrication of vision-correcting ophthalmological lenses.

This study presents the experimental and analytical evaluations on an innovative connection class under cyclic loading. The connection was an H- or I-shaped section as a short stub column (SSC) between the end-plate and the column. The stub section was bolted to the column flange on the one side and bolted to the beam along with the welded end-plate on the other side. Stiffeners were installed on the webs and flanges of the beam and stub to ensure the necessary stiffness of the connection. The variables included thickness of stub flange/web and height of stub web. The cyclic loading was applied on a sample of the proposed connection according to AISC ANSI/AISC 341-16 loading protocol. Experimental observations displayed that the proposed connection, one can either employ hot rolling sections or create the connection as a plate girder, in which case the flange thickness and stub web, as well as the distance between two flanges and their height, was obtained according to the demand and performance of the structure. The optimum cross-section of the stub was then obtained. Also, the analytical model was calibrated using the finite element method (FEM), and its performance was confirmed. The effective parameters of the proposed connection were determined by modeling in the FEM software, and the design method was presented.

Objective: In recent years, the field of Essential Thrombocythemia (ET) research has seen a significant accumulation of scientific findings, but comprehensive bibliometric analyses remain lacking. This study aims to fill that gap by performing a thorough bibliometric analysis of ET research, identifying key contributors and collaboration networks, and mapping the development trends to provide insights for future research directions. Methods: A bibliometric analysis of ET-related publications from 2001 to 2024 was conducted using CiteSpace, VOSviewer, and R packages. Data were retrieved from the Web of Science Core Collection, with a focus on publication volume, citation analysis, co-authorship networks, co-citation relationships, and citation bursts. Results: A total of 4,297 studies published in 778 journals were included in the analysis. ET research has seen rapid growth, with researcher clusters in the United States and Europe driving progress through extensive regional and international collaborations. Leading researchers, such as Ayalew Tefferi from the Mayo Clinic and Alessandro M. Vannucchi from the University of Florence, have made significant advances in ET classification, molecular mechanisms, targeted therapies, and disease management. The discovery of driver mutations, such as JAK2, has revolutionized the diagnostic and therapeutic approaches to ET. Research focus has shifted from clinical morphological diagnosis to molecular diagnostics, with the field now entering the era of targeted therapies. However, the inherent heterogeneity of ET continues to present challenges for the widespread implementation of personalized precision treatment. Conclusion: Bibliometric analysis demonstrates significant advances in ET research, particularly in molecular pathology and targeted therapies. However, the heterogeneity of ET remains a major obstacle to personalized treatment. Future research should focus on further elucidating the pathogenesis of ET and improving stratified management approaches to achieve individualized precision therapy.

Phosphorus (P) is an essential element in food production, but it is often largely unavailable for plants as it persists in soils in immobilized forms. Farmers have been using P fertilizers extensively to overcome this unavailability, leading to the exhaustion of non-renewable deposits of phosphorite, rising fertilizers prices and causing several environmental impacts such as eutrophication. Its large-scale utilization is also inefficient since most of the added P becomes quickly unavailable for the plants. Therefore, farming solutions that improve P uptake, P use efficiency of plants and P mobilization in soils are highly important. In this narrative review, we summarized and explored the link between the Silicon (Si) and P cycles in soils. Silicon is quasi-essential for plants, and it has been established that its presence in soil and uptake by plants has several benefits, especially in toxic and nutrient-deficient conditions. Here, we established that Si in soils can affect crop production in P-deficient conditions through: 1) the pH effect – Si improves organic matter decomposition and decreases Al3+ availability; the Si uptake effect – the deposited Si in the plant improves its photosynthetic performance, improves the root ability to uptake P, improves organic matter decomposition and increases P/Mn ration in plant, improving P use; and 3) the Si soil effect – Si stimulates phosphorite rocks weathering and competes with P for the binding places at the surface of Ak and Fe hydroxides, releasing P into soil solution. This positive effect of Si on P mobilization in soils and consequent use by crops should be further disseminated to farmers and other relevant stakeholders.

Cystic fibrosis (CF) diagnosis can be a challenge due to the large spectrum of pathogenic variants in the CFTR gene and the effects of complex alleles. Next-generation sequencing has improved our understanding of the contribution of these complex alleles to the wide spectrum of CF clinical symptoms and to the response to medications. Herein, we studied nine CF patients from six unrelated families carrying the complex allele p.[Ile148Thr;Ile1023_Val1024del] with a frequency of 0.18%. All the patients were from Central Mexico. This complex allele was found in trans with Class I and II pathogenic variants (PVs) such as [c.1521_1523del, p.(Phe508del), and c.3231_3232del, p.(Phe1078Profs*77)]. A targeted search of a dataset of 2,217 exomes from healthy individuals revealed that eight individuals (0.18%) carried the p.(Ile148Thr) variant, but only one (0.022%), who was also born in Central Mexico, was a carrier of the complex allele. These findings led us to hypothesize a founder effect for the p.[Ile148Thr;Ile1023_Val1024del] complex allele in Mexican patients with CF, probably through migration from the French-Canadian population in Mexico. Finally, protein modeling revealed that this complex allele disrupts the secondary structure of the CFTR protein and might alter the ion flow.

In this paper, various Ni-P composite coatings containing toner, MoS2, and nano-SiO2 particles were deposited on steel substrates by the electroless method. Then, the electrochemical properties of these coatings after a heat treatment process were compared. The microstructural evaluations were also done by using the optical and electron microscopy methods. Both Tafel polarization and electrochemical impedance spectroscopy techniques were utilized to survey the electrochemical behavior of such coatings. The surface morphology of all coatings contained cauliflower-like nodules. The X-ray diffraction patterns showed the crystalline phases of Ni and Ni3P for all coatings after the heat-treatment step. Obtained results showed that all composite coatings exhibited lower corrosion rates with respect to Ni-P coatings. Such a reduction was about 21.6-92.2%. This behavior was attributed to the presence of reinforcement as barriers for corrosive ion diffusion through the coating plus the changes in detected phases and thickness. Electrochemical impedance spectroscopy test results also demonstrated that the increase in the polarization resistance for composites coatings was about 18.4-85.3% after 1 h immersion in a 0.6M NaCl solution; however, when the immersion time increased to 24 h, such increased resistance changed to 18.1 to 73.1%. Totally, despite the lower deposition rate, the presence of MoS2 and nano-SiO2 particles were more effective than toner particles to raise the corrosion rate of the Ni-P coating.

In this paper, we investigate p-adic q-integral (q-Volkenborn integral) on Z_p of p-adic gamma function via their Mahler expansions. We also derived two q-Volkenborn integrals of p-adic gamma function in terms of q-Daehee polynomials and numbers and q-Daehee polynomials and numbers of the second kind. Moreover, we discover q-Volkenborn integral of the derivative of p-adic gamma function. We acquire the relationship between the p-adic gamma function and Stirling numbers of the first kind. We finally develop a novel and interesting representation for the p-adic Euler constant by means of the q-Daehee polynomials and numbers.

It is known that the class of p-normed spaces (0 < p ≤ 1) is an important generalization of usual normed spaces with rich topological and geometrical structure, but the most of tools and general principles in nature with nonlinearity have not been developed yet, thus the main goal of this paper is to develop tools for nonlinear analysis under the framework of p-vector spaces. In particular, we first develop the general fixed point theorems which provide solutions to answer Schauder conjecture since 1930’s in the affirmative for p-vector spaces when p = 1 (which is just general topological vector spaces); then the one best approximation result for upper semi-continuous mappings is given, which is used as a powerful tool to establish fixed points for non-self set-valued mappings with either inward or outward set conditions; and finally we establish comprehensive existence results of solutions for Birkhoff-Kellogg Problems, and the general principle of nonlinear alternative by including Leray-Schauder alternative and related results. The results given in this paper not only include the corresponding results in the existing literature as special cases, but also expected to be useful tools for the study of nonlinear problems arising from theory to practice.

While Neural Radiance Fields (NeRF) are gaining increasing interest in various domains as innovative methods for novel view synthesis and image-based reconstruction, their potential application in the realm of Cultural Heritage remains unexplored. Purpose of this paper is to assess the effectiveness of applying NeRF to sets of images of digital heritage objects and sites. The study’s findings demonstrate that NeRF could be valuable when used in combination with or as a comparison to other well-established techniques such as photogrammetry, to expand the possibilities of preserving and presenting heritage assets with enhanced visual fidelity and accuracy. Particularly, NeRF show promising results in improving the rendering of translucent and reflective surfaces, objects with homogeneous textures, and elements with intricate details. In addition, we demonstrate that, when considering the same set of input images (with known camera poses), reducing the image quality or the number of images results in significantly less information loss with NeRF compared to photogrammetry. This suggests that NeRF is preferentially suited for scenarios involving sparse information or low-quality photos or videos, which could be especially valuable in risky or challenging situations.

3D printing is playing an important role in cardiovascular disease by use of personalised models with replication of normal anatomy and pathology with high accuracy and reliability. While 3D printed heart and vascular models are shown to improve medical education, preoperative planning and simulation of cardiac procedures, and enhance communication with patients, 3D bioprinting however, represents a potential advancement of 3D printing technology by printing cellular or biological components, functional tissues and organs that can be used in a variety of applications in cardiovascular disease. Recent advances in bioprinting technology have shown the ability to support vascularisation of large scale constructs with enhanced biocompatibility and structural stability, thus creating opportunities to replace damaged tissues or organs. In this review, we provide an overview of the use of 3D bioprinting in cardiovascular disease with a focus on technologies and applications in cardiac tissues, vascular constructs and grafts, heart valves and myocardium. Limitations and future research directions are highlighted.

Tumor cells evolve in a complex and heterogeneous environment composed of different cell types and an extracellular matrix. Current 2D culture methods are very limited in their ability to mimic the cancer cell environment. In recent years, various 3D models of cancer cells have been developed, notably in the form of spheroids/organoids, using scaffold or cancer-on-chip devices. However, these models have the disadvantage of not being able to precisely control the organization of multiple cell types in complex architecture and are sometimes not very reproducible in their production, and this is especially true for spheroids. Three-dimensional bioprinting can produce complex, multi-cellular, and reproducible constructs in which the matrix composition and rigidity can be adapted locally or globally to the tumor model studied. For these reasons, 3D bioprinting seems to be the technique of choice to mimic the tumor microenvironment in vivo as closely as possible. In this review, we discuss different 3D-bioprinting technologies, including bioinks and crosslinkers that can be used for in vitro cancer models, and the techniques used to study cells grown in hydrogels; finally, we provide some applications of bioprinted cancer models.

Background: The main objective of this study is to develop a customized metatarsophalangeal implant for the treatment of various conditions affecting this specific joint. This approach involves replacing the joint with a custom implant designed specifically to fit each patient's unique anatomical structure. The need for custom implants stems from the obvious lack of size variety available, which presents a major challenge when, the search for the ideal size implant can be a hard task, also when considering the possibility of extensive modification of the bone to adapt it to the available implant. This adaptation, often synonymous with bone reduction, can cause significant post-operative pain for the patient and impact healing time. Methods: A comparative study of modeling software was carried out to select the perfect software, by defining and comparing the relevant criteria. Similarly, the different biomaterial options were examined and compared to select the one best suited to this project, mentioning the imaging modality used to determine the types of images used for our approach. Finally, the 3D printers used in this work were represented, highlighting their technical characteristics. Findings: A resin metatarsophalangeal implant prototype was created using 3D modeling and reconstruction software and tools. Interpretation: Reconstruction and 3D modeling techniques are revolutionizing implant creation, offering customized solutions for patients suffering from metatarsophalangeal joint disorders caused by a wide range of diseases. These results have significant implications for disability management and rehabilitation, encouraging further exploration and progress.

The main aim of this paper is to set some correlations between Boole polynomials and p-adic gamma function in conjunction with p-adic Euler contant. We develop diverse formulas for p-adic gamma function by means of their Mahler expansion and fermionic p-adic integral on ℤ_{p}. Also, we acquire two fermionic p-adic integrals of p-adic gamma function in terms of Boole numbers and polynomials. We then provide fermionic p-adic integral of the derivative of p-adic gamma function and a representation for the p-adic Euler constant by means of the Boole polynomials. Furthermore, we investigate an explicit representation for the aforesaid constant covering Stirling numbers of the first kind.

Background/Objectives: Stroke patients generally have balance and gait dysfunction due to decreased range of motion (ROM) and muscle strength of the ankle joint. A therapist can apply a floss band to enhance ROM, pain control, jumping performance, strength, myofascial release, and recovery from fatigue. This study compared the immediate effects of floss band application on ankle ROM, balance, and gait ability in stroke patients.; Methods: This study randomized 40 chronic stroke patients to either the floss (n = 20) or sham (n = 20) band group. Outcome measures were ankle ROM, weight bearing lunge test (WBLT) performance, standing balance, and gait ability. Outcome measures were assessed at baseline and immediately after applying the floss or placebo band.; Results: There were significant improvements in dorsiflexion (DF), WBLT, static balance, and foot strike in those who used the floss band compared to the sham group (all p &lt; 0.05).; Conclusions: The floss band improved ankle DF, balance, and gait, indicating that it is a feasible therapeutic method for improving ankle DF, balance, and gait in chronic stroke patients.

Background. Fibromyalgia (FM) is a complex condition marked by increased pain sensitivity and central sensitization. Studies often explore the link between FM and depressive-anxiety disorders, but few focus on dysthymia or persistent depressive disorder (PDD), which can be more disabling than major depression (MD). Objective. To identify clinical scales and subscales of the Personality Assessment Inventory (PAI) that effectively describe and differentiate the psychological profile of PDD, with or without comorbid MD, in FM patients with PDD previously dimensionally classified by the Millon Clinical Multiaxial Inventory III (MCMI-III). Method. An observational, cross-sectional study was conducted with 66 women (mean age 49.18, SD=8.09) from Hospital del Mar. The PAI, the MCMI-III, and Fibromyalgia Impact Questionnaire (FIQ) were used to assess the sample. Results. The PAI showed strong discriminative ability in detecting PDD, characterized by high scores in cognitive and emotional depression, and low scores in identity alteration, dominance, and grandeur. High scores in cognitive, emotional, and physiological depression, identity alteration, cognitive anxiety, and suicidal ideation, along with low scores in dominance and grandeur, were needed to detect MD with PDD. Discriminant analysis could differentiate 69.6-73.9% of the PDD group and 84.6% of the PDD+MD group. Group comparisons showed that 72.2% of patients with an affective disorder by PAI were correctly classified in the MCMI-III affective disorder group, and 70% without affective disorder were correctly classified. Conclusions. The PAI effectively identifies PDD in FM patients and detects concurrent MD episodes, aiding in better prognostic and therapeutic guidance.

In the domain of software engineering, the accurate and effective classification of requirements is of paramount importance. Proper classifications of these requirements enable developers to create robust and error-free software solution. Traditional methods of user requirements classification face the issue of the reliance on manual processes, which are time-consuming, labor-intensive, and prone to human error. The limitations of traditional methods underscore the need for more automated, scalable, and robust approaches to user requirements classification in order to meet the demands of modern software development practices. To improve the classification process, we employed a Deep Learning (DL) methodology termed the Bidirectional Long Short-Term Memory (Bi-LSTM) model to conduct feature extraction, after which we merged these feature vectors into ML classifiers. Our research methodology is structured around a five-step process. Initially, the textual input is tokenized and converted to lowercase. Subsequently, we eliminate all punctuation. The pre-processed text is then subjected to a Bi-LSTM (Bidirectional Long Short-Term Memory) model for feature vector extraction. After that, this feature vector is fed into different classifiers such as Medium KNN, Cubic KNN, Linear SVM, Quadratic SVM, and Cubic SVM and obtained an accuracy of around 99.60% to 99.80% on a publicly available dataset of requirements.

Galactic rotation curve was formulated before the Sgr A* had been confirmed. The action of the Sgr A* on the rotation curve has not been considered. Now, it was observed that the fastest stars in the Milky Way is in the distance less than 0.5pc from the Sgr A*. It is contradicted with the current galactic rotation curve in which the orbital velocity near the center of the galaxy is the smallest. And, because of the advance of technology, it was observed that the circular velocity curve of the Milky Way from 5 to 30 kpc is with a significantly faster decline (Keplerian decline) compared to the inner parts. It is contradicted with the current curve in which the out parts could be larger or no decline. And, it was observed that the fast galaxy bar continue challenge the standard cosmology. For the reasons, we present an improved galactic rotation curve.

As a branch of regional innovation theories, social filter theory fundamentally reveals the reasons for the geography of innovation in different countries and regions. However, compared with some other regional innovation theories, social filter theory has been as silent as a sleeping beauty and hasn’t been fully developed. For enriching and developing social filter theory, this article systematically traces the source and comments on four aspects: the concept of social filter, the construction and measurement of indicators of social filter, the mechanism and empirical re-search of social filter affecting regional innovation and innovation transformation. Until recently regional innovation theories primarily focused on the superficial description of the phenomenon of innovation, but lack of attention to the local social filter condition of innovation generation and innovation transformation, which are the pre-condition of constructing mature innovation system. Therefore, additional efforts are still required to fill the current knowledge gap from the recom-mended directions in the article.

This study examines the significant impact of Houthi insurgent activities on maritime traffic within the strategic Red Sea and Suez Canal routes, essential conduits for global trade. It explores the correlation between regional instability, exemplified by Houthi actions from November 19, 2023, to February 5, 2024, and changes in maritime traffic patterns and operational efficiency. This study seeks to answer a critical question in transport geography: How does regional instability, exemplified by Houthi insurgent activities, affect maritime traffic patterns and the operational efficiency of the Red Sea and Suez Canal? Using descriptive statistics, qualitative analysis, and geospatial methods, the research highlights recent trends in maritime traffic and incidents, revealing spatial and geopolitical challenges in this crucial trade route.Findings indicate a notable decline in maritime activity in the Gulf of Aden and Suez Canal due to security concerns from Houthi attacks, prompting a significant shift to alternative routes, particularly around the Cape of Good Hope. This shift underscores the broader implications of regional instability on global trade and the importance of maintaining uninterrupted maritime flow. The study also emphasizes the economic ramifications, such as increased operational costs and freight rates due to longer transit times and enhanced security measures.The research concludes with a call for improved maritime security protocols and international cooperation to protect these strategic maritime pathways. It contributes to the discourse on transport geography by quantifying the direct impacts of regional conflicts on maritime logistics and proposing strategies for future resilience, highlighting the interconnected nature of global trade and security and the need for collective action against evolving geopolitical challenges.

The fall armyworm (FAW), Spodoptera frugiperda, a major pest in maize production, was assessed for its temporal and spatial distribution in maize fields during both the off and rainy seasons of 2021 and 2022. In this study, 30 and 50 maize plants were randomly sampled using a "W" pattern during the dry and rainy seasons, respectively. Larval density, infestation rates, and damage severity were monitored over time. Taylor's power law and the mean crowding aggregation index were applied to evaluate the dispersion patterns of the larvae. The results indicate a higher infestation rate and larval density in agroecological zone AZE 8 (fisheries zone of South Benin) compared to AZE 6 (ferralitic soils zone) during the off-season. In the rainy season, while the percentage of damaged plants was higher in AZE 8, no significant differences in larval density between the two zones were observed. The dispersion analysis revealed moderate aggregation (aggregation index = 1.25) with a basic colony of 2.08 larvae, reflecting the aggregation oviposition behavior of FAW. This study provides valuable monitoring data on the FAW's distribution, offering insights for further research on population dynamics and developing predictive models for integrated pest management strategies.

Objective: To explore the acceptability and feasibility of conducting comprehensive, community-based, hy-brid (in-person and virtual) mental health screening and feedback with diverse youth in the community. Methods: The Screening and Support for Youth intervention provides comprehensive assessment and thera-peutic feedback in community settings including symptoms, diagnoses, functional impairment, suicide, and clinical risk. Symptom severity, seven diagnoses and suicidality were assessed with the Kiddie Computer-ized Adaptive Test. Functional impairment was evaluated by youth self-report on the Weiss Functional Im-pairment Rating Scale. Measures were scored according to nationally developed norms and an algorithm was developed to aggregate symptoms and functioning to determine clinical risk. The results were discussed with participants in a motivational interview to promote insight and engagement in an online intervention. Results: Methodological innovations included using a QR code for recruitment, integrated in-person and virtual participation, and expansion from in-person recruitment within the schools to virtual engagement with youth throughout the community. The final sample included disproportionately more Black or African American and Hispanic youth as compared to school and community statistics, suggesting that hybrid re-search may facilitate recruitment of diverse populations. Qualitative interviews indicated that the screening and feedback raised youth awareness of their wellbeing and/or distress, its impact on their functioning, and engagement with options for improving wellbeing. Conclusion: Hybrid research, developed as a necessity during the pandemic, proved advantageous to the feasibility and acceptability of community-based recruit-ment of at risk, minoritized youth.

In order to deal with imprecision, ambiguity, and uncertainty in data analysis, Pawlak introduced rough set theory in 1982. This paper aims to expand the scope of basic set theory developed by presenting the notions of δP-upper and δP-lower approximations, that are based on the notion of δP-open sets, we additionally examine a few of their fundamental characteristics.

This work reports the role of structure and composition on the determination of the performances of p-type SnOx TFTs deposited by rf magnetron sputtering at room temperature, followed by a post-annealed step up to 200 °C at different oxygen partial pressures (Opp), between 0% and 20%, but where the p-type conduction was only observed between 2.8–3.8%. The role of structure and composition were evaluated by XRD and Mössbauer spectroscopic studies. The study allows to identify the best phases/compositions and thicknesses (around 12 nm) to be used that lead to the production of TFTs with a bottom gate configuration, on glasses coated with conductive Indium Tin Oxide, followed by Aluminium Titanium Oxide dielectric layer with saturation mobility of 4.6 cm²V⁻¹s⁻¹ and on-off ratio above 7 × 10⁴, operating at the enhancement mode with a saturation voltage of −10 V.

In this paper, we investigate several relations for p-adic gamma function by means of their Mahler expansion and fermionic p-adic q-integral on ℤ_{p}. We also derive two fermionic p-adic q-integrals of p-adic gamma function in terms of q-Boole polynomials and numbers. Moreover, we discover fermionic p-adic q-integral of the derivative of p-adic gamma function. We acquire a representation for the p-adic Euler constant by means of the q-Boole polynomials. We finally develop a novel, explicit and interesting representation for the p-adic Euler constant including Stirling numbers of the first kind.

In this paper, we investigate p-adic q-integral (q-Volkenborn integral) on ℤ_{p} of p-adic gamma function via their Mahler expansions. We also derived two q-Volkenborn integrals of p-adic gamma function in terms of q-Daehee polynomials and numbers and q-Daehee polynomials and numbers of the second kind. Moreover, we discover q-Volkenborn integral of the derivative of p-adic gamma function. We acquire the relationship between the p-adic gamma function and Stirling numbers of the first kind. We finally develop a novel and interesting representation for the p-adic Euler constant by means of the q-Daehee polynomials and numbers.

It is increasingly common for experiments in biology and medicine to involve large numbers of hypothesis tests. A natural graphical method for visualizing these tests is to construct a histogram from the p-values of these tests. In this article, we examine the shapes, both normal and abnormal, that these histograms can take on, as well as present simple inferential procedures that help to interpret the shapes in terms of diagnosing potential problems with the experiment. We examine potential causes of these problems in detail, and discuss potential remedies. Throughout, examples of abnormal-looking p-value histograms are provided and based on case studies involving real biological experiments.

Background. One of the most important prognostic factors in periampullary and pancreatic cancers is perineural infiltration, whose preoperative detection could be decisive in selecting which patients should not undergo upfront surgery. We evaluated CA 19.9 and the Neutrophil-to-lymphocyte ratio (NLR) as preoperative predictors of perineural invasion (PNI). Methods: Retrospective analysis including patients with periampullary and pancreatic cancers who underwent curative resection from January 2013 to August 2023 in our institution. A univariate analysis and multivariate analysis were performed to analyze the association between the CA 19.9 and NLR with the existence of PNI. Results: A total of 136 patients were included in the study. PNI was observed in 95 (69.9%) patients. The selected cut-off points were NLR: 2.2 and CA 19.9: 37 U/mL. In univariate analysis, NLR (p=0.001) and CA 19.9 (p=0.006) were statistically significantly associated with PNI. In multivariate analysis, baseline NLR levels (p=0.012; OR: 1.95; 95%CI: 1.16-3.29) as well as CA 19.9 levels (p=0.026; OR: 1.67; 95%CI: 1.06-2.64) remained independent prognostic factors for PNI. The area under de ROC curves was 0.67 for CA 19.9 (p=0.004) and 0.72 for NLR (p<0.001). A sensitivity of 65.9% with a positive predictive value of 81.7% were obtained for CA 19.9, and a sensitivity of 62.1% with a positive predictive value of 84.3% were achieved for NLR. Conclusion: Preoperative CA 19.9 and NLR levels seem to be good predictors of PNI. In patients with normal levels of CA 19.9, preoperative NLR above of 2.2 should be an indication for neoadjuvant therapy.

.Citizen or community science (CS) projects in the marine environment rarely consider carbon footprint and sustainability. In this case study, we assessed the effectiveness of ten CS methods used by tourists in the Great Barrier Reef Marine Park (GBRMP) and Coral Sea Marine Park (CSMP). We also assessed baseline coral reef knowledge of the tourists, observations of marine species and the communication of our results to the public. Specifically, the tourists utilised up to ten methods: iNaturalist, CoralWatch, Great Barrier Reef Census, Eye on the Reef (EoR), environ-mental DNA (eDNA) testing kits, photogrammetry, social surveys, and Red Map, as well as ma-rine debris and marine vegetation collections. A total of 10,421 data points were collected across 14 days, including 5,390 records (52 % of the total) uploaded to iNaturalist, comprising 640 plant animal species. Public awareness of the CS expedition reached over 700,000 people based on estimates from advertising, media, social media, family and friends, and conference presenta-tions. We estimated the total carbon footprint for the expedition as 268.7 tonnes of CO2 or 4.47 tonnes of CO2 per person, equivalent to $112 AUD needed to offset this input. Based on these re-sults, our recommendations to leverage CS methods include governmental review strategies, temporal replication to allow the measurement of changes through time, integrating sustainabil-ity into CS ecotourism platforms, and encouraging broad participation.

Pastırma is an ethnic meat product defined as dry-curing, drying, pressing the whole muscles of cattle and buffalo, and coating them with a special paste containing fenugreek seed flour, garlic, milled red capia pepper, and water. In this narrative literature review, historical aspects of pastırma, its definition and classification, detailed production steps, composition and yield, chemical and microbiological properties, pastırma fraud and customer concerns are mentioned. In the shape of the narrative review, relevant studies were identified by searching Scopus, Science Direct, Web of Science, Trdizin, and Google Scholar Search included English- or Turkish-based articles, online reports, books, and electronic books. The keywords "pastırma, pastirma, çemen, cemen, cemening, cemen paste, Fenugreek" were used. The results of this review indicate that future studies on pastırma may focus on related cultural aspects, elimination of unpleasant odour from fenugreek, histological and chemical effects of pressing meat parts, kinetics of drying, osmotic dehydration, and developing new starter combinations.

The basic helix-loop-helix (bHLH) transcription factor family, is the second-largest superfamily in plants after MYB, which plays a significant role in the physiological processes of plant growth, tissue development, and environmental variation. However, the systematized study of the bHLH transcription factor family has not yet been conducted in A. catechu. Herein, we conducted genome genome-wide investigation of AcbHLH genes located on 16 chromosomes of A. catechu. A phylogenic tree was constructed to adjudge their homology of genes, and 24 subgroups were identified. Finally, we analyzed the dynamic changes of gene-expression levels of nine AcbHLH genes in response to drought and salt in leaves and roots. The expression patterns of 9 AcbHLH genes show differences in leaves and roots. Under stress conditions induced by salt and drought, AcbHLH22, AcbHLH62 and AcbHLH45 are significantly upregulated in both leaves and roots. In conclusion, this study will substantially contribute to the foundation for exploring the role of the bHLH superfamily in A.catechu in dealing with abiotic stresses.

Breast cancer is currently the second leading cause of death worldwide, accounting for 15% of all deaths (8.2 million deaths). Approximately 20% of breast cancer diagnoses are triple-negative breast cancer (TNBC), a type of cancer that lacks receptors for estrogen (ER negative), progesterone (PR negative), and human epidermal growth factor receptor 2 (HER2/neu negative). Consequently, TNBC doesn’t respond to hormonal or targeted therapies, making it challenging to treat due to its rapid growth, metastasis, and high recurrence rate within the first three years of therapy. Alternative chemotherapies are needed to address this problem. Pharmacological dose of vitamin C (high-dose VC) has been identified as a potential treatment for some cancer cells. The present study aimed to evaluate whether VC has a therapeutic effect on TNBC using MDA-MB-231 cells as the model. MTT assay, Hoechst 33342 staining, Nuclear ID Red/Green staining, Rhodamine 123 staining, and Western blot analysis were employed to test the hypothesis that pharmacological dose of VC can kill TNBC cells. Upregulation of Apaf-1, caspases -3, -6, -7, -8, and -9, inhibition of matrix metalloproteinases (MMP-2 and MMP-9), reduction in cell cycle protein expression, and enhancement of tumor suppressor proteins such as p53 and p21 indicated that pharmacological dose of VC has promising anti-cancer properties in the treatment of TNBC.

The rapid pace of urbanization, coupled with the growing need for environmental sustainability and technological innovation, has brought smart city initiatives to the forefront of global urban development. This paper provides a comparative analysis of smart city policies from leading cities such as Oslo, Zurich, and Canberra, and derives strategic insights for Qatar. By examining the strategies, priorities, outcomes, and challenges associated with implementing smart city initiatives in these cities, the study identifies areas of alignment and divergence with Qatar's own smart city policy framework. The research highlights potential opportunities for cross-learning and suggests how Qatar can leverage lessons from international best practices to enhance its smart city initiatives. Key areas of focus include fostering strategic partnerships, promoting innovation, and ensuring effective governance and data management systems. The findings provide actionable insights to improve the effectiveness of Qatar's smart city projects, aligning them with the Qatar National Vision 2030.

Recent studies with ApoE knockout (ApoE-/-) mice deficient for PACAP (pituitary adenylate cyclase-activating polypeptide) or its receptor PAC1 provide evidence for a possible involve-ment of immune- and vasoregulatoy PACAP signaling at the PAC1 receptor in atherogenesis and plaque associated vascular inflammation. Therefore, we tested the PAC1 receptor agonist Maxadilan and the PAC1 selective antagonist M65 on plaque development and lumen stenosis in the ApoE-/- atherosclerosis model for possible anti-atherogenic effects. Adult male ApoE-/- mice were fed a cholesterol-enriched diet (CED) or standard chow (SC) treat-ed with Maxadilan, M65 or Sham. Effects of treatment on atherosclerotic plaques, lumen stenosis, apoptosis and pro-inflammatory signatures were analyzed in the brachiocephalic trunk (BT). The percentage of Maxadilan treated mice exhibiting plaques under SC and CED was lower than that of Sham or M65 treatment indicating opposite effects of Maxadilan and M65. Maxadilan ap-plication inhibited lumen stenosis under SC and CED compared to Sham. In spite of significantly increased cholesterol levels, lumen stenosis of Maxadilan-treated mice was similar under CED and SC. In contrast, M65 under SC or CED did not reveal a significant influence on lumen steno-sis. Maxadilan significantly reduced the TNF-α+ area in the plaques under CED, but not under SC. In contrast, the IL-1β+ area was reduced after Maxadilan treatment under SC, but remained unchanged under CED compared to Sham. Maxadilan reduced the caspase-3+ area in the media under both SC and CED without affecting lipid content in plaques. Despite persisting hypercholesterolemia, Maxadilan reduces lumen stenosis, apoptosis and TNF-α driven inflammation. Our data suggest that Maxadilan provides atheroprotection by act-ing downstream of cholesterol-induced vascular inflammation. This implicates the potential of PAC1-specific agonist drugs against atherosclerosis even beyond statins and PCSK-9.

Background: Urinary tract infections (UTI) are a significant health concern, particularly in women, with almost half of them experiencing at least one UTI in their lifetime. This problem is further compounded by the high recurrence rate within 6-12 months. Postmenopausal women are especially vulnerable to recurrent UTI due to the natural decline in estrogen levels, which alters the urogenital epithelium and subsequently affects the urogenital microbiome. Methods: This study included 674 female patients that were admited at "Dr. Carol Davila" Central Military Emergency University Hospital in Bucharest over a period of 3 years. Results: Of the 674 women with urinary tract infection, 435 (79.3%) had more than one positive culture, and 239 (35.4%) experienced at least one recurrent urinary tract infection 6-12 months after the initial diagnosis. The mean age of women with urinary tract infection was 63 (± 15.61 years). Recurrent urinary tract infections were most prevalent in those aged 65-80 years (52%). Escherichia coli was detected in 71% of the positive cultures. Conclusions: The management of recurrent urinary tract infections in women presents a complex challenge that necessitates a multifaceted approach. The emerging understanding of the urobiome and its role in bladder health offers promising avenues for developing targeted interventions. As research in this field advances, it is imperative to integrate these new insights into clinical practice to balance traditional antibiotic treatments with novel strategies that consider the intricate microbial ecosystem of the urinary tract.

Disruptions in power quality have a negative impact on many energy consumers. These include lighting, where interference manifests itself, among others, in the form of light flickering. The article presents phenomena accompanying the operation of modern light sources against the background of exemplary results of studies on the flicker of conventional light sources, such as incandescent or fluorescent lamps. To assess the effects of these phenomena, it is necessary to use measures other than those traditionally used. The results of measurements carried out in accordance with different recommendations take into account both power supply disturbances and the properties of modern light sources.

Manufacturing of facial epithesis is a complex technological process including several traditional stages of production, accompanied by aggravated psycho-emotional status of the patient. One of the main factors causing discomfort in patients with facial defects is the process of obtaining silicone impressions from the wound surface and the long waiting period for the final epithesis. Active development of digital technologies in medicine and dentistry helps specialists not only to automate most of the traditional stages of manufacturing of dento-mandibular and facial prostheses, but also improves the quality of life of patients by increasing the efficiency of services and reducing the production time of prosthetic structures. The application of digital technologies in the production of facial epithesis was difficult due to the lack of specialized 3D-software for modeling and material for further additive manufacturing of structures. The authors developed a unique technology for 3D modeling and additive manufacturing of facial epithesis, including a 3D CAD module and material for 3D printing. The primary objective was to fabricate immediate facial prostheses in the postoperative period in the shortest possible time until the final epithesis was fabricated.

The present study aimed to characterize the microstructure of a temporary 3D printing resin (Resilab Temp), evaluating the optical properties and mechanical behavior according to different post-processing curing times. For the analysis of the surface microstructure and establishment of the best printing pattern, samples in bar format following ISO 4049 (25 x 10 x 3 mm) were designed in CAD software (Rhinoceros 6.0), printed on the W3D printer (Wilcos), and light-cured in Anycubic Photon at different times (without curing, 16 minutes, 32 minutes, and 1 hour). For the structural characterization, analyses were carried out in FTIR (Fourier Transform Infrared Spectroscopy) and Scanning Electron Microscopy (SEM). The mechanical behavior of the resin was based on flexural strength tests and Knoop microhardness. Color and translucency analysis were performed with a spectrophotometer (VITA Easy Shade Advanced 4.0), which was evaluated following CIELab, using gray, black, and white backgrounds. All analyses were performed immediately after making the samples and repeated after thermal aging with 2 thousand cycles (5-55 °C). The results obtained were statistically analyzed with a significance level of 5%. FT-IR analysis showed about a 46% degree of conversion on the surface and 37% in the center of the resin sample. The flexural strength was higher for the groups polymerized for 32 min and 1h, while the Knoop microhardness did not show a statistical difference between the groups. Color and translucency analysis also did not show statistical differences between groups. According to all the analyses carried out in this study, for the evaluated material, the post-polymerization time of 1 hour can be suggested to improve the mechanical performance of 3D-printed devices.

In recent years, Additive Manufacturing (AM), commonly referred to as 3D printing, has garnered the attention of the scientific community due to its capacity to transform ordinary and traditional items into customized materials at an affordable cost, through various AM processes. Antimicrobial/antibiofilm 3D printed materials are one of the most trending research topics, owing to the growing concerns over the emergence of complex microbial structures called "biofilms" on various surfaces. The review provides an overview of the evolution of additive manufacturing (AM) technologies and their various derivatives, along with a brief description of their materials and applications. It also introduces how biofilms can represent an advantageous lifestyle for microbial populations. The primary objective of this research was to conduct a systematic review on the development of planctonic or biofilm forms of microorganisms on 3D printed materials. The article summarizes commonly studied microorganisms on these materials and presents their 3D printing process, materials, as well as the fields covered by each of the analyzed papers. To the best of our knowledge, this is the first all-inclusive systematic review that amalgamated research conducted in diverse fields to assess the development of biofilms on surfaces produced through three-dimensional printing. Most notably, this review presents a comprehensive account of sustainable approaches for producing antimicrobial materials through 3D printing. Additionally, we assess their advancements in various fields such as medicine, environment, agri-food, and other relevant sectors. The findings of our literature review can be used to recommend appropriate microorganisms, 3D printing materials, and technologies for academic and industrial research purposes focusing on the development of microbial biofilms on 3D printed surfaces. Furthermore, it highlights the potential of environmentally-friendly modified AM technologies to combat biofilms in clinical and non-clinical areas. Our goal with this review is to help readers gain a better understanding of fundamental concepts, inspire new researchers, and provide valuable insights for future empirical studies focused on eradicating biofilms from 3D printed materials.

The increasing request of digitized data among several fields, including the built environment and Cultural Heritage (CH) one points out the need of proficient ways to access, archive and share 3D data and related information among users. The sector of reality capture produces accurate and reliable products that can support building management and CH maintenance, at the price of heavy and resource-demanding data. An emerging solution to this problem is represented by the web platforms for 3D data management, that promise to relieve users from the costs of archive and hardware, providing effective visualization, access and sharing tools. The panorama of commercial web platforms is analyzed according to the Software as a Service business model and the features of some representative platforms are exposed. The paper discusses the main advantages in terms of diffused access and collaboration and the potential issues concerning the long-term archive and data persistence. The future perspectives of the web platform sector are promising as, according to the current development path, could be able to empower the built environment and CH sector with a diffused, systematic and aware use of 3D data.

Generating executable code from natural language instructions using Large Language Models (LLMs) poses challenges such as semantic ambiguity and understanding task- specific contexts. To address these issues, we propose a system called DemoCraft, which enhances code generation by leveraging in-context learning and demonstration selection, combined with latent concept learning. Latent concept learning introduces additional concept tokens, which are trainable embeddings that capture task-specific knowledge. We then test our system on two major datasets: MBPP and HumanEval. Our experimental results demonstrate that the proposed system achieves an approximate 2x increase in the pass@k metric compared to baseline models. Furthermore, we introduce two novel evaluation metrics: correctness@k and similarity@k. Our empirical studies indicate that our system attains nearly a 3x improvement in these metrics as well.

Helium is a strategic rare gas resource related to national security and the development of high-tech industries, the high-quality development of helium industry chains has a great significance to improve the security of helium resource. This paper through literature and market research, summarizes the progress of helium resource endowmen, exploration and development, supply and demand pattern, trade market and industrial technology, equipment through literature and market research in the world, analyses the development situation of global helium resources industry chains. This study proposes the development status and challenges of China's helium industry and the corresponding development path of helium industry based on the upstream, midstream, downstream and downstream indicators. Most of the countries in the world have not started helium exploration or remain in low exploration level, but the exploration practice shows that global helium resource potential is considerable; helium exploration and development subjects become diversified in recent years, which may change the global helium supply and demand pattern; The helium reservoir forming theory and exploration and development technology are underdeveloped, and the helium extraction equipment is continuously improved; The global helium production capacity, supply and demand，trade pattern market would be profoundly changing. For a long time, the United States has had an absolute say in the global helium trade system, the contradiction between supply and demand would persist for a long time and significant price fluctuations. China's helium development challenges and opportunities coexist considering the global helium industry chain existing pattern and the new trend of development. There is an urgent need to build an independent and controllable , stable and resilient helium industrial chain, and provide helium resources guarantee for the development of high-tech industries.

Objective: The aim of this review was to identify newly discovered bacteria from individuals with periodontal/peri-implant diseases and organize them in new clusters (GF-MoR complexes) to update Socransky’s complexes (1998). Methods: The focus question was developed based on the PCC (Population, Concept, Context) strategy: “In patients with periodontal and/or peri-implant disease, what bacteria (microorganisms) were detected through laboratory assays?” The search strategy was applied to PubMed/MEDLINE, PubMed Central, and Embase. The search keyterms, combined with Boolean markers, were: (1) bacteria, (2) microbiome, (3) microorganisms, (4) biofilm, (5) niche, (6) native bacteria, (7) gingivitis), (8) periodontitis, (9) peri-implant mucositis, and (10) peri-implantitis. The search was restricted to 1998–2024 and English language. The bacteria groups in the oral cavity obtained/found were retrieved and were included in the GF-MoR complexes which were based on the disease/condition, presenting six groups: (1) Health, (2) Gingivitis, (3) Peri-implant mucositis, (4) Periodontitis, (5) Peri-implantitis, and (6) Necrotizing and Molar-Incisor (M-O) pattern Periodontitis. The percentual found per group refers to the number of times a specific bacterium was found associated with a particular disease. Results: A total of 381 articles were found; 162 articles were eligible for full-text reading (k=0.92); 9 articles were excluded with justification, and 153 were included in this review (k=0.98). Most of the studies reported results for Health condition, Periodontitis, and Peri-implantitis (3 out of 6 GF-MoR clusters), limiting the number of bacteria found in the other groups. Therefore, it is essential to understand that bacterial colonization is a dynamic process, and the bacteria present in one group can also be present in other one or others, such as observed with the bacteria found in all groups (Porphyromonas gingivalis, Tannarela forsythia, Treponema denticola, and Aggregatibacter actinomycetemcomitans) (GF-MoR’s red Triangle); the second most observed bacteria were grouped at GF-MoR’s blue Triangle: Porphyromonas spp., Prevotela spp., and Treponema spp., present in 5 of the six groups; and the third most detected bacteria were clustered in the grey Polygon (GF-MoR’s grey Polygon): Fusobacterium nucleatum, Prevotella intermedia, Campylobacter rectus, and Eikenella corrodens. These three geometric shapes had the most relevant bacteria for periodontal and peri-implant diseases. Specifically, per group, GF-MoR’s Health had 58 species; GF-MoR’s Gingivitis presented 16 bacteria; the GF-MoR’s Peri-implant mucositis included 17 bacteria; GF-MoR’s Periodontitis group had 101 different bacteria; GF-MoR’s Peri-implantitis presented 61 bacteria; and the last group was a combination of Necrotizing diseases and Molar-Incisor (M-I) pattern Periodontitis, with seven bacteria. Observing the top seven bacteria of all groups, all were gram-negative; Groups 4 and 5 (Periodontitis and Peri-implantitis) presented the same top seven bacteria. Conclusion: For the first time in the literature, GF-MoR’s complexes are presented, gathering the bacteria according to the condition found and including more bacteria than Socransky’s complexes. On this understanding, this study can drive future research into treatment options for periodontal and peri-implant diseases, guiding future studies and collaborating to prevent and worsen systemic conditions. Moreover, it permits the debate about the evolution of the bacterial clusters correlated to periodontal and peri-implant diseases and conditions.