As critical biocontrol agents, Trichoderma and Metarhizium have demonstrated vast potential in disease prevention and pest control respectively. Current applications, however, are predominantly confined to singular use or simplistic combinations of the two fungi. This study innovatively utilizes Metarhizium and Trichoderma as experimental subjects, employing non-targeted metabolomics to compare the differences in metabolites between co-culture and separate fermentation. The metabolite distinctions in co-culture are meticulously analyzed using sample correlation, least squares discriminant analysis, cluster analysis, and KEGG enrichment analysis. Metabolome sequencing analysis is then applied to compare the co-culture fermentation filtrate with Trichoderma atroviride and Metarhizium anisopliae. Differential metabolite analysis found that co-culture had significantly up-regulated or down-regulated metabolites compared to singular cultures.However,significant metabolite discrepancies are discovered in singular cultures, notably the up-regulated metabolites such as osthole and spirocyclic amine, which have documented antibacterial functions that may prove effective against Fusarium graminearum. Ultimately, the findings from this research contribute to the exploration of synergistic applications of biocontrol fungi and serve as a valuable reference for future development of bio-pesticides for disease and pest control.

A challenge in building large-scale superconducting quantum processors is the precise control and manipulation of the qubit state. However, the crosstalk between the microwave control lines impedes the parallel execution of high-fidelity digital and analog quantum operations. Here, we propose and demonstrate a universal compensation protocol for calibrating the microwave signal crosstalk. We also introduce amplified error sequences to optimize the accuracy. Furthermore, we show a definitive improvement in parallel gate operations with crosstalk cancellation, demonstrating the technique's effectiveness. This work paves the way for superconducting hardware that features automated calibration of microwave crosstalk, leading to enhanced fidelities in multiqubit circuits.

Dye/salt separation has gained increasing attention in recent years, prompting the quest for cost-effective and environmentally-friendly raw materials for synthesis high performance nanofiltration (NF) membrane for effective dye/salt separation. Herein, a high-performance loose structured NF membrane was fabricated by via a simple vacuum filtration method using a green nanomaterial, 2,2,6,6-tetramethylpiperidine-1-oxide radical (TEMPO)-oxidized cellulose nanofiber (TOCNF), by sequentially filtrating larger-size and finer-size TOCNFs on a microporous substrate, followed by cross-linked with trimesoyl chloride. The resultant TCM membrane possesses a separating layer composed entirely of pure TOCNF, eliminating the need for other polymer or nanomaterials additives. TCM membranes exhibits high performance and effective dye/salt selectivity. Scanning Electron Microscope (SEM) analysis shows that the TCM membrane with Fine-TOCNF layer has a tight layered structure. Further characterizations via Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction (XRD) confirm the presence of functional groups and chemical bonds of the crosslinked membrane. Notably, the optimized TCM-5 membrane exhibits a rejection rate of over 99% for various dyes (Congo red, orange yellow) and 14.2% for NaCl, showcasing a potential candidate for efficient dye wastewater treatment.

Chemical flooding methods are used to recover the remaining oil after water flooding, and surfactant-polymer (SP) flooding is an important chemical flooding technology. It is of great significance to design and screen high-performance oil displacement agents in order to overcome the increasingly challenging high temperature (>70 ℃) and high salinity (>10,000 mg/L) reservoirs. Based on the characteristics of high temperature (70 ℃) and high salinity (151,000 mg/L) in the Qinghai Gasi reservoir, the performance of the SP flooding system was studied. This study considered interfacial tension, emulsification, viscosity, compatibility, and oil displacement efficiency. The selected formula demonstrated high resistance to both salinity (151,000 mg/L) and temperature (70 ℃), characterized by a low oil-water interfacial tension (10-2 mN/m) and high viscosity (18.13 mPa.s). After water flooding achieved an oil recovery rate of 64.64%, the subsequent replacement rate of crude oil increased by 26.95%, confirming that SP flooding can be used as a technology for enhancing oil recovery in high-temperature, high-salinity reservoirs represented by Qinghai Gasi reservoirs.

In this review, we outline our current understanding of the mechanisms involved in the absorption, storage, and transport of dietary vitamin A to the eye, the trafficking of rod opsin protein to the photoreceptor outer segments, which encompasses the logistical backbone required for visual function. Two key mechanisms of this process are emphasized in this manuscript: Ocular and systemic vitamin A membrane transporters, and rhodopsin transporters. Understanding the complementary mechanisms responsible for the generation and proper transport of the retinylidene opsin to the photoreceptor outer segment will eventually shed light on the importance of genes encoded by these proteins, and their relationship on normal visual function and in the pathophysiology of retinal degenerative diseases.

Nowadays, there is an increasing concern about environmental challenges ranging from emissions to overconsumption. Most of the environmental problems today are direct consequences of human consumption. Understanding the factors that affect consumer purchasing decisions is critical to developing demand for and commitment to sustainable consumption. In this regard, this study aims to explore the environmentally sustainable consumption behavior of Ethiopian consumers by using an extended model of the theory of planned behavior. Data were collected using a self-administered questionnaire having open and closed-ended questions. A total of 523 Ethiopian consumers were selected using convenience sampling technique. Structural equation modeling with AMOS V.26.0. was applied for data analysis. The findings show that Ethiopian consumers have very low awareness about the impact of their clothing consumption and disposal. Their consideration of sustainability attributes during purchasing decisions is also low. The structural equation model analysis showed that all variables had a positive and significant effect on the dependent variables at p<0.05, except the effect of personal norms on an environmentally responsible purchasing intention. These results provide additional evidence on the role of environmental labels in purchasing sustainable apparel products. The results of the study allow a better understanding of the factors determining sustainable consumption behavior and suggest practical solutions to their producers. As theory-building activities, with implications for the conceptualization of sustainable consumption behavior are sparse in the literature, this work has also been able to detect sustainable consumption behavior trends and practices by using the availability of a sustainable apparel product and consumers price perceptions of environmentally responsible apparel as a mediating effect of intention and behavior in developing countries, particularly Ethiopia.

Background/Objectives: The use of post-operative drains in gynaecologic oncology procedures is controversial with evidence both supporting and questioning their efficacy. Proponents argue that such drains help detect complications early, reduce abscess formation, and also alleviate post-operative pain. On the other hand, drains are associated with increased risks of incisional hernia, infection, prolonged hospitalization, and postoperative pain. Methods: We conducted a research in the PubMed database and supplemented it with a manual search to retrieve addition-al papers eligible for inclusion. Results: Their use is not always found to improve outcomes, no-tably in surgeries such as a radical hysterectomy with pelvic lymphadenectomy, where they may actually enhance lymphocyst formation and other complications. In cytoreductive surgery for ovarian cancer, negative pressure wound therapy showed some potential benefits, but evidence remained inconclusive due to limited studies. The international guidelines presented in this re-view, suggest avoiding the routine use of drains and promote early removal when their use is necessary. Conclusions: This review aims to present an update on the current knowledge re-garding the role of drainage in gynaecologic oncology and while further good-quality research is required, particularly in high-risk surgical procedures, numerous prospective trials have exten-sively addressed the topic, trying to provide clear suggestions.

Existing methods of hyperspectral anomaly detection still face several challenges: 1) Due to the limitations of self-supervision, avoiding the identity mapping of anomalies remains difficult; 2) The ineffective interaction between spatial and spectral features leads to the insufficient utilization of spatial information; 3) Current methods are not adaptable to the detection of multi-scale anomaly targets. To address the aforementioned challenges, we proposed a blind spot network based on multi-scale blind spot convolution for HAD. The multi-scale mask convolution module is employed to adapt to diverse scales of anomaly targets, while the dynamic fusion module is introduced to integrate the advantages of mask convolutions at different scales. The proposed approach includes a spatial-spectral joint module and a background feature attention mechanism to enhance the interaction between spatial-spectral features, with a specific emphasis on highlighting the significance of background features within the network. Furthermore, we propose a preprocessing technique that integrates pixel shuffle down-sampling (PD) operation with spatial spectral joint screening to address the issue of anomalous identity map-ping and facilitate finite-scale mask convolution to adapt to the detection of more scale targets. The proposed approach was assessed on four real hyperspectral datasets comprising anomaly targets of different scales. The experimental results demonstrate the effectiveness and superior performance of the proposed methodology compared with nine state-of-the art methods.

The research presented in the article is devoted to the study of the influence of phase compounds on the friability of the Fe-Si-Mn-Al complex alloy. The urgency of the problem lies in the development of technology for producing a non-scatterable alloy from manganese-containing ores and high-ash coals. The main goal of the work is to determine the range of alloy compositions and the resulting phases that affect the dispersibility of the alloy, which is critically important for its industrial implementation. Research methods include thermodynamic diagram analysis (TDA) using data on the standard enthalpy of formation of intermetallic compounds, as well as experimental tests in an ore-thermal electric furnace with a capacity of 200 kV*A. The results show that Fe-Si-Mn-Al complex alloys form a variety of silicide and aluminide phases, including intermetallic compounds and ternary systems, which is critical for understanding and controlling their physicochemical properties. When smelting a complex alloy, the content of leboite (Fe3Si7) in the Fe-Si-Mn-Al system plays a significant role. The development of smelting technology will be aimed at avoiding the FeSi2-Fe3Si7-F2(FeAl3Si2)-Mn11Si19 tetrahedron area. This approach to controlling the composition of a complex alloy is critical to ensuring its consistent friability properties in industrial applications. Thus, this work represents an important step in understanding the physical properties and stability of Fe-Si-Mn-Al complex alloys, which have potential for widespread use in metallurgical and other industrial applications.

Flap surgery is a common method used to cover defects following tumor ablation, trauma, or infection. However, insufficient vascularity in the transferred flap can lead to flap necrosis and failure. Proper postoperative monitoring is essential to prevent these complications. Recently, research has explored the use of infrared thermal imaging in plastic surgery, leading to its clinical application. This study investigates the use of a forward-looking infrared (FLIR) camera to monitor blood flow in flaps. In the study, 28 rats underwent reverse McFarlane flap surgery, and their flaps were analyzed using a FLIR thermal imaging camera seven days post-surgery. Additionally, thermal images of flaps were taken on postoperative days 0, 1, 2, 3, and 7 in 22 patients. The study focused on temperature differences between normal skin and the perforator compared to the average flap temperature. Results showed that the temperature difference was higher in the necrosis group and increased over time in cases of total necrosis. A lower perforator temperature compared to the flap's average indicated vascular compromise, potentially leading to flap failure. The FLIR camera, being contact-free and convenient, shows promise for understanding and inferring the clinical progression of flaps in postoperative monitoring.

Citrus species essential oils (EOs) are significant sources of bioactive compounds and demonstrate diverse therapeutic effects. However, limited documentation exists regarding the phytochemicals associated with their biological activities. This study aims to assess the antioxidant activity, plant inhibitory properties, and brine shrimp cytotoxic effects of EOs derived from three Citrus species: C. sinensis, C. limon, and C. hystrix. Utilizing chemometric analysis and gas chromatography-mass spectrometry (GC-MS) fingerprints, the volatile components contributing to antioxidant activity were elucidated. The peels of the Citrus samples were hydro-distillated to obtain EOs, and subsequently subjected to antioxidant, plant inhibitory, and brine shrimp cytotoxic assays. The results indicated that C. limon EO exhibited the highest antioxidant activity, while C. hystrix and C. sinensis EOs demonstrated pronounced inhibitory effects against Aetrmia salina and Lactuca sativa, respectively. GC-MS analysis facilitated the identification of key compounds in each EO. Principal component analysis (PCA) and hierarchy cluster analysis (HCA) effectively categorized Citrus EOs based on their antioxidant properties, highlighting the proximity of C. limon and C. sinensis. Among the identified compounds, D-limonene, α-Terpineol, Caryophyllene, (+)-3-Carene, β-Pinene, (-)-Spathulenol, trans-p-Mentha-1(7),8-dien-2-ol, and trans-Verbenol were the most discriminating compounds affected the antioxidant activity of C.limon and C. sinensis EOs.

Myasthenia gravis (MG) is a disease characterized by typical clinical and immunopathogenic pe-culiarities, which correlate with age and sex/gender. Accordingly, MG patients show thymic al-terations and auto-antibodies productions, that can be the expression of a different pathogenetic mechanism related to age and gender. This determines, in relation to age at and sex/gender, a dif-ferent MG onset, prognosis, and outcome. Therefore, diverse MG forms can be identified, classi-fied, and characterized in relation to their different features, and precisely there are early onset and late-onset forms of MG. It has been hypothesized that the cause of appearance the two diverse forms of MG can be ascribed mainly to the diverse genetic and epigenetic factors. In this narrative review, we will analyze and discuss about the interplay of age- and sex-related factors (i.e. genet-ic and epigenetic factors) related to two different MG forms and how they contribute to their di-verse pathogenesis.

Originating in the Mediterranean, B. oleracea is grown all over the world and is highly valued for its nutritional value and variety in cooking. Its susceptibility to pests, diseases, and environmental stressors, however, poses significant challenges to sustaining consistent crop quality and productivity. The BASIC PENTACYSTEINE gene significantly impacts plant growth and responses to abiotic stresses. Nevertheless, little is known about its precise role and the underlying biological processes in B. oleracea. Eleven BPC genes in B. oleracea were identified by a thorough genome-wide investigation and categorized into three categories according to their structural traits and gene motifs. There were eight different chromosomes on which these BoBPCs were located. Comparative synteny analysis was used to reveal the evolutionary traits of potatoes, Arabidopsis, and B. oleracea. The BoBPC family genes in B. oleracea were found to have specific cis-elements linked to growth, stress responses, and hormone regulation when their promoter regions were studied. Cuticular wax synthesis expression revealed that all BoBZR1 genes, from wild to mutant, expressed at varied amounts in distinct types. Moreover, distinctive BoBPC gene expression patterns were found in the seven distinct tissues that were studied. Our thorough analysis shows that the BoBPC family is widely involved in B. oleracea developmental processes. The present findings provide an established theoretical basis for further exploration into the composition and roles of BoBPC in B. oleracea.

Despite the efforts made to stop the tuberculosis (TB) epidemic, it still remains one of the leading causes of death from an infectious disease. Previous work in the group uncovered a new family of amides which showed promising activities against Mycobacterium tuberculosis. A closer look at the literature showed that these compounds are structurally related to the DNB family of DprE1 inhibitors, so, we decided to study a wide range of substituted amides and determine their activity, focusing on unexplored structures related to the dinitrobenzamides (DNB) found in the literature. To synthesize our library of compounds we started from 3,5-dinitrobenzoic acid to form the nitroaromatic core that is characteristic of the DNB’s, to which we then added linear or cyclic amine moieties. Additionally, the impact of terminal aromatic moieties was also assessed for some derivatives, via an ether, ester, or amide bond. In order to obtain the desired derivatives, multiple synthetic approaches were used, mainly focused on nucleophilic addition/elimination reactions, SN2 reactions and Mitsunobu reactions. The activity was impacted mainly by two structural features, the addition of an aromatic moiety as a terminal group and the type of the linker. The most interesting compounds exhibited activities comparable to isoniazid and DNB1. Computational studies were also performed aimed at understanding their possible interactions with DprE1. The most active compounds are a good starting point for further development, and we plan to study an extended family of compounds based in those structures.

This paper intends to discuss SSLs, how they work, their advantages and drawbacks. It will end with the author’s thoughts on the efficacy of the system and whether it is a viable solution for the majority of network security problems or if those drawbacks prevent that.

Alzheimer's disease (AD) is a progressive neurodegenerative disorder characterized by cognitive impairment and memory loss. Oxidative stress (OS) has emerged as a central element in the pathophysiology of AD, linking various pathological features including amyloid-β (Aβ) plaque formation, tau hyperphosphorylation, and synaptic dysfunction. This review comprehensively examines the role of OS in AD, focusing on the mechanisms of reactive oxygen species (ROS) production, mitochondrial dysfunction, and their impact on neuronal integrity. Additionally, the review highlights recent advances in antioxidant therapy. Elevated ROS levels in the aging brain exacerbate oxidative damage to lipids, proteins, and DNA, contributing to neuronal atrophy and synaptic loss. Mitochondrial dysfunction further amplifies OS, disrupting cellular energy metabolism and promoting neurodegeneration. Despite the strong association between OS and AD, antioxidant therapies have shown inconsistent clinical outcomes. Emerging strategies targeting offer promising avenues for therapeutic intervention. This review highlights the need for a multifaceted approach in understanding and mitigating OS-related damage in AD, aiming to pave the way for more effective treatments and improved patient outcomes.

In the design of real-world networks, researchers evaluate various structural parameters to assess vulnerability, including connectivity, toughness, and tenacity. Recently, the tightness metric has emerged as a potentially superior vulnerability measure, although many related theorems remain unknown due to its novelty. Harary graphs, known for their maximum connectivity, are an important class of graph models for network design. Prior work has evaluated the vulnerability of three types of Harary graphs using different parameters, but the tightness metric has not been thoroughly explored. This article aims to calculate the tightness values for all three types of Harary graphs. First, it will attempt to calculate the lower bound for the value of the tightness parameter in Harary graphs using existing lemmas and theorems. Then, by presenting new lemmas and theorems, we will try to find the exact value or upper bound for this parameter in Harary graphs. For the first type of Harary graph, the tightness is precisely determined, while for the second and third types, upper bounds are provided due to structural complexity. The lemmas, theorems, and proof methods presented in this research may be used to calculate other graph and network parameters. However, the newness of the tightness parameter means that further research is needed to fully characterize its properties.

Neurologic disorders such as traumatic brain injury, multiple sclerosis, Alzheimer’s disease, and drug-resistant epilepsy have a high socioeconomic impact around the world. Current therapies for these disorders are often not effective. This creates a demand for the development of new therapeutic approaches to treat these disorders. Recent data suggest that autoreactive naturally occurring immunoglobulins produced by subsets of B cells called B1 B cells combined with complement are actively involved in the processes of restoration of neuronal functions during pathological conditions and remyelination. The focus of this review is to discuss the possibility of creating specific therapeutic antibodies that can activate and fix complement to enhance neuronal survival and promote central nervous system repair after injuries associated with many types of neurodegenerative diseases.

1) Background- Coronary artery bypass grafting (CABG) is a common surgical intervention for patients with severe coronary artery disease. The Model for End-Stage Liver Disease (MELD) score has been widely used to predict mortality risk in patients with end-stage liver disease, but its utility in predicting postoperative outcomes in cardiac surgery patients is less well-established. 2) Methods-This retrospective study aims to investigate the association between preoperative MELD score and post-operative complications, length of hospital stay, and mortality in patients under-going coronary artery bypass grafting. This is a single-center, retrospective cohort study conducted at a tertiary care academic medical center. The study includes all adult patients who underwent elective coronary artery bypass grafting between January 2011 and December 2020. Preoperative MELD scores were calculated for each patient, and postoperative outcomes including major ad-verse cardiac events, length of hospital stay, and 30-day mortality was assessed. To ensure a homogeneous study cohort, we excluded patients who underwent emergent cardiac procedures or had incomplete data necessary for the calculation of MELD scores and assessment of postoperative outcomes. Data was extracted from the electronic medical records, including patient de-mographics, comorbidities, preoperative laboratory values, operative details, and postoperative outcomes. The study protocol was approved by the Institutional Review Board, and the require-ment for informed consent was waived due to the retrospective nature of the study.3) Results- This study reveals a statistical association between the MELD score calculated at admission and the length of hospital stay, duration in the ICU, patient age, and the duration of aortic clamping and extracorporeal circulation. Specifically, there is an exponential increase in the MELD score corre-lating with the rise in these factors, both collectively and individually, highlighting a significant relationship between the duration of extracorporeal circulation and aortic clamping time. 4) Conclusion-Patients with a high MELD score had an increased risk of postoperative complications and mortality compared to those with a low MELD score. Careful preoperative patient selection and optimization of the patient's clinical condition may improve outcomes in patients with advanced liver disease undergoing cardiac surgery.

To address the issue of reduced orbit estimation accuracy resulting from discrepancies between in-orbit measured geomagnetic field values and IGRF model values in autonomous orbit estimation of microsatellites based on geomagnetic field measurements, this study introduces an adaptive cubature H-infinity filtering algorithm. Firstly, it presents the low-altitude orbital dynamics model and geomagnetic field measurement model for microsatellites. Subsequently, within the adaptive cubature H-infinity filtering algorithm, a spherical simplex rule and a second-order Gaussian-Legendre quadrature criterion are employed to compute the spherical surface integral and radial integral. Additionally, a spherical simplex-radial quadrature rule is proposed to enhance the approximation accuracy of nonlinear Gaussian weighted integrals. Furthermore, by integrating extended H-infinity filtering based on game theory with the cubature quadrature rule, an inverse proportional relationship between constraint level and filtering innovation is established. This allows for adaptive adjustment of the constraint level to enhance robustness against model errors. Finally, through semi-physical simulation experiments, it is demonstrated that compared with traditional algorithms, the proposed algorithm improves autonomous orbit estimation position accuracy of microsatellites by 7.49%, while also enhancing velocity accuracy by 3.1%, thus validating its effectiveness.

This paper presents a comprehensive study on applying machine learning (ML) techniques for real-time credit card fraud detection. With the increasing prevalence of credit card fraud, financial institutions face the challenge of detecting fraudulent transactions promptly and accurately. This research evaluates various ML models, including Logistic Regression, Decision Trees, Random Forests, XGBoost, and Deep Convolutional Neural Networks, for their effectiveness in identifying fraudulent activities. Utilizing PySpark for processing large-scale transaction data, the study highlights the importance of real-time analysis, adaptive learning, and handling imbalanced datasets. Key findings reveal that XgBoost, with its balance of accuracy and complexity, emerged as the most promising model, achieving an accuracy rate of 98% in detecting fraudulent transactions. The paper further discusses the potential of ensemble methods, graph-powered systems, and intelligent sampling in enhancing fraud detection capabilities. Challenges such as overfitting, data access, and the need for real-time analysis are addressed. Future research directions include implementing models in live transaction environments, expanding model applicability across financial platforms, and developing advanced anomaly detection methodologies. This study underscores the pivotal role of machine learning in safeguarding financial transactions against fraud, offering significant implications for consumers, financial institutions, and the broader financial ecosystem.

Unmanned aerial vehicles (UAVs) have increasingly become integral to multi-access edge computing (MEC) due to their flexibility and cost-effectiveness, especially in the B5G and 6G eras. This paper aims to enhance the Quality of Experience (QoE) in large-scale UAV-MEC networks by minimizing the shrinkage ratio through optimal decision-making in computation mode selection for each user device (UD), UAV flight trajectory, bandwidth allocation, and computing resource allocation at edge servers. However, the interdependencies among UAV trajectory, binary task offloading mode, and computing/network resource allocation across numerous IoT nodes pose significant challenges. To address these challenges, we formulate the shrinkage ratio minimization problem as a mixed-integer nonlinear programming (MINLP) problem and propose a two-tier optimization strategy. To reduce the scale of the optimization problem, we first design a low-complexity UAV partition coverage algorithm based on the Welzl method and determine the UAV flight trajectory by solving a Traveling Salesman Problem (TSP). Subsequently, we develop a coordinate descent (CD) based method and an alternating direction method of multipliers (ADMM) based method for network bandwidth and computing resource allocation in the MEC system. The CD-based method is simple to implement and has a low computational complexity, while the ADMM-based method can further enhance the optimization result through joint optimization. Extensive simulations demonstrate that our proposed algorithms perform well in large-scale edge networks and outperform other representative benchmark methods.

The effect of wave forces on the structural safety of fixed oscillating water-column (OWC) devices is critical. In this study, a three-dimensional numerical model of an oscillating water column (OWC) device is constructed using the computational fluid dynamics software OpenFOAM. Subsequently, the hydrodynamic performance of the numerical model is comprehensively validated. Finally, the hydrodynamic performance data are analyzed in detail to obtain meaningful conclusions. The results indicate that the horizontal wave force on the OWC device is approximately 6.6 to 7.9 times greater than the vertical wave force, whereas the lateral wave force is relatively small. Both the horizontal and vertical wave forces decrease as the relative water depth increases under a constant wave period and height. The horizontal wave force increases linearly with the wave height, whereas the vertical wave force increases with the square of the wave height. In addition, the highest dynamic water pressure is observed at the interface between the water surface and device, both within and outside the front wall of the gas chamber. The dynamic water pressure at different locations on the front chamber increases and subsequently decreases as the wave frequency increases.

Keywords: contamination; bioaccumulation; fish and mollusks tissue; ecosystem components; heavy metals; organochlorine pesticides; polychlorinated biphenyls; polycyclic aromatic hydrocarbons.

Almost two decades ago, Ernesto P. Borges and Bruce M. Boghosian embarked on the intricate task of composing a manuscript to honor the profound contributions of Constantino Tsallis to the realm of statistical physics, coupled with a concise exploration of q-Statistics. Fast forward to Constantino Tsallis’ illustrious 80th birthday celebration in 2023, where Deniz Eroglu and Ugur Tirnakli delved into Constantino’s collaborative network, injecting renewed vitality into the project. With hearts brimming with appreciation for Tsallis’ enduring inspiration, Eroglu, Boghosian, Borges and Tirnakli proudly present this meticulously crafted manuscript as a token of their gratitude.

As the fast growth of information technology (IT), the safety of image transmission and the storing of images are increasingly concerned. Traditional image encryption algorithms have certain limitations in transmission and security, so there is an urgent need for a secure and reliable image encryption algorithm. A universal compression sensing (CS) image encryption (IE) algorithm based on DNA-triploid mutation (DTM) is presented in this paper. Firstly, by using CS algorithm an image is compressed while obtaining a range of chaotic sequences by iteration of chaotic map. Then DNA sequences are generated by encoding the image, and based on the DTM, new mutant DNA sequences are generated according to specific rules. Next, the chaotic sequences are operated at the DNA level to do confusion and diffusion operations on the image to ensure the security of the data. At last, DNA decoding is carried out to obtain the compressed-encrypted image. Both simulation experiments and performance tests fully show that a high level of security and reliability of the proposed algorithm in protecting image privacy is achieved.

Nowadays circular economy trend drives researchers in the recovery of various bioactive compounds from agri-food by-products. Enzyme-assisted extraction (EAE) is shown as an innovative green technology for the effective extraction of various phytochemicals from agri-food section by-products, therefore this study aimed to evaluate the application of EAE as green technology to obtain extracts from olive leaves (Olea europaea) for potential industrial production. EAE was conducted under various enzyme dose combinations, and incubation time (120 min). Obtained extracts were characterized in terms of total polyphenols (TP) and Total Antioxidant Activity (AA). Firstly, the enzyme synergistic effect in enzymatic extraction of polyphenols was evaluated. TP optimal extraction conditions (468.19 mg GAE/L) were achieved after EAE (50-50%) and for AA (69.85 AA%). According to the above results, a second experimental part occurred for the incubation time (min.) and enzyme dose (mL) of optimal extraction conditions of olive leaves. Results indicated EAE as an excellent choice for green extraction of polyphenols from the olive leaves.

Tremor is a prevalent neurological disorder characterized by involuntary shaking or trembling of body parts. This condition impairs fine motor skills and hand coordination to varying degrees and can even affect overall body mobility. As a result, tremors severely disrupt the daily lives and work of those affected, significantly limiting their physical activity space. This study developed an innovative Spatial Augmented Reality (SAR) system aimed at assisting individuals with tremor disorders to overcome their physical limitations and expand their range of activities. The system integrates eye-tracking and Internet of Things (IoT) technologies, enabling users to smoothly control objects in the real world through eye movements. It employs a virtual stabilization algorithm for stable interaction with objects in the real environment. The study comprehensively evaluated the system's performance through three experiments: 1) assessing the effectiveness of the virtual stabilization algorithm in enhancing the system's ability to assist individuals with tremors in stable and efficient interaction with remote objects; 2) evaluating the system's fluidity and stability in performing complex interactive tasks; 3) investigating the precision and efficiency of the system in remote interactions within complex physical environments. The results demonstrate that the system significantly improves the stability and efficiency of interactions between individuals with tremor and remote objects, reduces operational errors, and enhances the accuracy and communication efficiency of interactions.

Abstract. This paper proposes a Second Order Terminal Sliding Mode (2TSM) approach to the trajectory tracking of Differential Drive Mobile Robot (DDMR). Within this cascaded control scheme, the 2TSM dynamic controller, at the inner most loop, tracks the robot’s velocity quantities; while a kinematic controller, at the outer most loop, regulates the robot’s positions. In this manner, chattering is greatly attenuated and finite time convergence is guaranteed by the second order TSM manifold which involves higher order derivatives of the state variables, resulting in inherently robust as well as fast and better tracking precision. The simulation results demonstrate the merit of the proposed control methods.

The yeast Saccharomyces cerevisiae ensures successful fermentation in winemaking, although the persistent use of commercial strains lead the loss of aroma complexity of wines. Hence, the research of indigenous S. cerevisiae with proper oenological features and well adapted to specific wine-growing area become of great interest for winemakers. Here, 206 S. cerevisiae strains were isolated from two wineries during two-year sampling campaign and bio-typed with the aim to evaluate the occurrence and persistence of S. cerevisiae wild population linked to each winery. Both wineries belonging to the same Verdicchio DOC wine area (Castelli di Jesi), and never used commercial yeasts during fermentation. Results showed a specific and varied population of S. cerevisiae in each winery without cross-contamination each other and with commercial starter strains. Moreover, inside each winery it was observed a persistent of some dominant biotypes over the time, indicating a sort of “winery-effect”. The evaluation of S. cerevisiae populations for the oenological characters showed a proper and well distinct aromatic imprinting on the resulted wines confirming the “winery effect”.

In GNSS/IMU integrated navigation systems, factors such as satellite occlusion and non-line-of-sight conditions can lead to degradation of satellite positioning results, Subsequently affecting the overall accuracy of the integrated navigation system. To address this issue and ef-fectively utilize historical pseudorange information from satellites, this paper proposes a graph optimization-based GNSS/IMU model with virtual constraints. These virtual constraints are con-structed using satellite ‘s position from previous time step, the rate of change of pseudoranges, and ephemeris data. This virtual constraint can serve as an alternative solution for individual satellites in case of signal anomalies, ensuring the integrity and continuity of the graph optimi-zation model. Additionally, this paper conducts an analysis of the graph optimization model constructed using these virtual constraints, comparing it with traditional integrated navigation graph optimization model, and analyzes and reconstructs the marginalization process based on these virtual constraints. The experimental results, compared with tightly coupled Kalman fil-tering and the original graph optimization method on a set of real-world data, demonstrate that the introduction of virtual pseudoranges maintains high positioning accuracy. The RMSE error between it and the original graph optimization remains within 5%, affirming the high feasibility of this approach.

Adenomyosis, a benign gynecological condition characterized by the infiltration of endometrial tissue into the myometrium, poses significant challenges to women's reproductive health. Recently, the landscape of adenomyosis diagnosis transformed significantly, thanks to advancements in imaging technologies such as transvaginal ultrasound and magnetic resonance imaging. This lead to a noticeable shift in the demographic profile of patients diagnosed with adenomyosis, including younger women of reproductive age who frequently present with a diverse array of symptoms. Approximately 20% of women are affected by adenomyosis. Adenomyosis manifests with various subtypes, distinct epidemiological profiles, symptomatology, and treatment responses, necessitating tailored approaches for optimal management. Despite its clinical significance, adenomyosis remains understudied, resulting in a significant disparity in research and literature compared to other gynecological conditions. The severity of adenomyosis is compounded when coexisting with endometriosis, particularly deep infiltrating endometriosis (DIE), leading to exacerbated fertility issues and severe symptomatology. The wide range of symptoms, including adverse pregnancy outcomes such as pre-eclampsia, highlights its wider impact and emphasizes the need for increased awareness of the condition. Furthermore, Adenomyosis is frequently associated with treatment failure in endometriosis, contributing to dienogest resistance, elevated discontinuation rates, and persistent pain post endometriosis surgery. Additionally, the lack of specific treatments tailored to adenomyosis poses a considerable challenge in clinical management.

This paper presents a compact wideband circularly polarized cross dipole antenna with low-pass filter response. It consists of two pairs of folded crossed dipole arms printed separately on both sides of the top substrate, and the two dipole arms on the same surface are connected by an annular phase-shifting delay line to generate circular polarization. A bent metal square ring and four small metal square rings around the cross dipoles are employed to introduce new resonant frequencies, effectively extending the impedance and axial ratio bandwidth. Four square patches printed on the middle substrate are connected to the ground plane by the vertical metal plates, in order to reduce the antenna height. Thus, a compact wideband circularly polarized antenna is realized. In addition, a transmission zero can be introduced at the upper frequency stopband by the bent metal square rings, without using extra filter circuits. For verification, the proposed model is implemented and tested. The overall size of the model is 90mm×90mm×33mm(0.37λ0×0.37λ0×0.14λ0, λ0 denotes the center operating frequency). The measured impedance bandwidth and 3 dB axial ratio bandwidth are 53.3% and 41%, respectively. More than 15 dB upper-band radiation suppression level is realized, indicating a good low-pass filter response.

The electric vehicle (EV) industry challenges battery joining technologies by requiring higher energy density both by mass and volume. Improving the energy density via new battery chemistry would be the holy grail but is seriously hindered and progresses slowly. In the meantime, alternative ways, such as implementing more efficient cell packaging by minimizing the electrical resistance of joints are of primary focus. In this paper we discuss the challenges associated with the electrical characterisation of laser soldered joints in general, and the minimization of their resistive losses, in particular. In order to assess the impact of the joint resistance on the overall resistance of the sample, the alteration in resistance was monitored as a function of voltage probe distance and modelled by finite element simulation. The experimental measurements showed two different regimes: one far from of the joint area and another in its vicinity and within the joints cross section. The presented results confirm the importance of the thickness of the filler material, the effective and the total soldered area, and the area and the position of the voids within the total soldered area in determining the electrical resistance of joints.

The raw material purchasing (RMP) problem is to determine the purchasing quantities of raw materials in given periods or cycles. Raw material purchasing optimization is crucial for large-scale steel plants because it is closely related to the supply of raw materials and cost savings. The raw material purchasing of large-scale steel enterprises is characterized by many varieties, large quantities, and high costs. The RMP objective is to minimize the total purchasing cost consisting of the price of raw materials, purchasing set-up costs, and inventory costs and meet product demand. We present a mixed integer linear programming (MILP) model and a column generation (CG) solution for the resulting optimization problem. The column generation algorithm is the generalization of the branch & bound algorithm with solving the linear programming (LP) relaxation of MILP using column generation (CG), and its advantage is to handle large-sized MILPs. Experimental results show the effectiveness and efficiency of the solution.

In the last decades we have experienced great social, cultural, and educational changes, spending more time performing tasks in near vision and less hours in outdoor activities, having more overexposure to digital screens, especially the youngest and increasingly from younger ages. It is common to see cases when performing tasks in near vision the posture or position of the head is not adequate, especially the youngest, being essential to have a correct posture of the head to avoid visual, muscular, or articular problems. We present a procedure to try to control the correct position of the head in real time when performing close-up activities. The aim is to detect the inclination of the head and to know if a bad position is adopted due to a visual problem or simply to inadequate visio-postural habits, warning us of the postural anomaly to correct it.

While numerous studies have explored the correlation between the built environment and ride-hailing demand, few have assessed their nonlinear interplay. Utilizing ride-hailing order data and multi-source built environment data from Nanjing, China, this paper uses the machine learning method, eXtreme Gradient Boosting (XGBoost), combined with SHapley Additive exPlanations (SHAP) and Partial Dependence Plots (PDP) to investigate the impact of built environment factors on ride-hailing travel demand, including their non-linear and threshold effects. The findings reveal that dining facilities have the most significant impact, with a contribution rate of 30.75%, on predicting ride-hailing travel demand. Additionally, financial, corporate, and medical facilities also exert considerable influence. The built environment factors need to reach a certain threshold or within a certain range to maximize the impact of ride-hailing travel demand. population density, land use mix and distance to the subway station collectively influence ride-hailing demand. The results are helpful for TNCs to allocate network ride-hailing resources reasonably and effectively.

This paper addresses the input coupling problem for the shape memory alloy (SMA) actuated parallel platform with completely unknown nonlinear dynamics. The problem means that in a parallel platform with multiple SMA actuators acting together, the displacement of one of the actuators will simultaneously affect the remaining actuators to change. Due to the coupling problem and nonlinear characteristics of the SMA actuators, it is not easy to control the platform to achieve bi-directional swing with completely unknown nonlinear dynamics. Therefore, a model-free adaptive sliding mode control method is proposed to improve the control accuracy of the complex motion of the platform, avoiding the complex modeling process of the SMA actuated parallel platform. Based on the model-free adaptive control (MFAC) theory, a multiple input and multiple output (MIMO) dynamic linearized mathematical model of the parallel platform is established using the online input and output data of the system. Then, a sliding mode controller is designed based on the dynamic model. A rigorous theoretical analysis proves that the proposed model-free adaptive sliding mode controller is able to stably control the SMA actuated parallel platform, and its tracking error is uniformly ultimately bounded (UUB). Finally, experiments are conducted on the established SMA actuated parallel platform. The results show that the proposed model-free controller is feasible and effective, and can control the system well to achieve the complex motion of bi-directional swing.

The optimal structural design is imperative to minimize material consumption and reduce the environmental impact of construction. Given the complexity in the formulation of structural design problems, the process of optimization is commonly performed using artificial intelligence (AI) global optimization, such as Genetic Algorithm (GA). However, the integration of AI-based optimization together with visual programming (VP) in building information modeling (BIM) projects warrants further investigation. This study proposes a workflow by combining structure analysis, VP, BIM, and GA to optimize trusses. The methodology encompasses several steps including: (i) generation of parametric trusses in Dynamo VP; (ii) performing the finite element modeling (FEM) using Robot Structural Analysis (RSA); (iii) retrieving and evaluating the FEM results interchangeably between Dynamo and RSA; (iv) finding the best solution using GA; and (v) importing the optimized model into Revit, enabling the user to perform simulations and engineering analysis, such as life cycle assessment (LCA) and quantity surveying. The feasibility of the proposed workflow was tested on benchmark problems and compared with open literature. The outcomes of this study offer insight into the opportunities and limitations of combining VP, GA, FEA, and BIM for structural optimization applications, particularly to enhance structural efficiency and sustainability in construction.

The healthcare situation in Africa is characterized by limited resources and a high burden of disease, presenting significant challenges to the healthcare systems in the region. The integration of Artificial Intelligence (AI) technologies in African healthcare holds immense potential for addressing these challenges and improving health outcomes. This paper aims to provide a comprehensive understanding of the current healthcare landscape in Africa and the urgent need for AI-driven solutions.In addition to discussing the potential applications of AI in African healthcare, such as disease diagnosis, treatment planning, and medical imaging analysis, this manuscript seeks to shed light on the specific challenges hindering the implementation of AI in the region. By providing detailed examples and case studies, we aim to offer insights into the obstacles that need to be overcome and potential solutions that can be pursued.By leveraging AI technologies, Africa has the opportunity to revolutionize its health systems, bridging the gap in access to quality healthcare across the continent. The objective of this review article is to not only highlight the potential benefits that AI can bring to African healthcare but also to emphasize the urgent need for action and collaboration in implementing and scaling up AI innovations in the region. By doing so, African countries can pave the way for improved health outcomes and ensure that their populations receive the healthcare services they deserve.

This study aims to examine the non-volatile Particle Number (PN) emissions of a retrofitted Heavy-Duty Spark-Ignition (HD-SI) engine powered by liquefied petroleum gas (LPG) under both steady-state and transient conditions. The engine was tested under seven steady-state operating points to investigate the PN behavior and Particle Size Distribution (PSD) upstream and down-stream of the Three-Way Catalyst (TWC). This analysis intends to assess the impact of including particles with diameters ranging from 10 nm to 23 nm in the total particle count, a consideration for future regulations. The study employed the World Harmonized Transient Cycle (WHTC) for transient conditions to encompass the same engine working region used in the steady-state analysis. A Dekati FPS-4000 diluted the exhaust sample to measure the PSD and PN for particle diameters between 5.6 nm and 560 nm using the TSI-Engine Exhaust Particle Sizer (EEPS) 3090. Findings indicate that PN levels tend to increase downstream of the TWC under steady-state conditions in operating points with low exhaust gas temperatures and flows (equal to or less than 500 °C and 120 kg/h). Furthermore, the inclusion of particles with diameters between 10 nm and 23 nm leads to an increase in PN emissions by 17.70% to 40.84% under steady conditions and by an average of 40.06% under transient conditions, compared to measurements that only consider particles larger than 23 nm. Notably, in transient conditions, most PN emissions occur during the final 600 seconds of the cycle, linked to the most intense phase of the WHTC.

This paper presents the PEnsemble 4 model, a sophisticated machine learning framework that integrates IoT-based environmental data to accurately forecast maize yield. With the projected significant growth in global maize demand over the next decade, the inherent risks posed by the crop’s dependence on weather conditions necessitate improved prediction capabilities. The PEnsemble 4 model, developed with high accuracy, incorporates comprehensive datasets encompassing soil attributes, nutrient composition, weather conditions, and UAV-captured vegetation imagery. By employing a combination of Huber and M estimates, the PEnsemble 4 model effectively analyzes temporal patterns in vegetation indices, specifically CIre and NDRE, which serve as reliable indicators of canopy density and plant height. In addition, this research significantly contributes to precision agriculture by offering an efficient and sustainable alternative to conventional farming practices through precise yield predictions. Notably, the PEnsemble 4 model enables earlier estimation, advancing the timeline for yield prediction from the conventional day 100 in the R6 stage to day 79 in the R2 stage. This improvement enhances decision-making processes in farming operations. The remarkable accuracy rate of 91% underscores the importance of adopting a multifaceted data approach that harnesses IoT-derived environmental insights. Additionally, the PEnsemble 4 model extends its benefits beyond yield prediction, facilitating the detection of water and crop stress, as well as disease monitoring in broader agricultural contexts. Ultimately, the PEnsemble 4 model establishes a new standard in maize yield prediction, revolutionizing crop management and protection through the synergistic utilization of IoT and machine learning technologies.

Rheumatoid arthritis (RA) is a chronic inflammatory disease. Despite new methods of diagnostics and treatment as well as extensive biological and immunosuppressive treatment, the etiology of RA is not fully understood. Moreover, the problem of diagnosis and treatment of RA patients is still current and affects a large group of patients. It is suggested that these ER-related features may impair adaptation to chronic stress, inferring the risk of rheumatoid arthritis. The main goal in this study was evaluation of changes in mRNA translation to determine chronic ER stress conditions in rheumatoid arthritis patients. The study group consist of 86 individuals including total 56 rheumatoid arthritis patients and 30 healthy controls. The expression level of mRNA form blood samples of RA patients as well as controls of the PERK-UPR associated genes: p-eIF2, BCL-2, PERK, ATF4, BAX were investigated by Real-Time qPCR. GAPDH expression was used as a standard control. Considering the median, the expression of PERK, BCL-2, p-eIF2, ATF4, BAX was found to be significantly increased in the blood of RA patients compared with the control group. The p-value for the PERK gene was 0.0000000036, the p-value for the BCL-2 gene was 0.000000014, the p-value for the p-eIF2 gene was 0.006948, the p-value for the ATF4 gene was 0.0000056 and the p-value for the BAX gene was 0.00019, respectively. Thus, it can be concluded that targeting of the components of the PERK-dependent UPR signaling pathway via small-molecule PERK inhibitors, may contribute to the development of novel, innovative treatment strategies against rheumatoid arthritis.

The modern supply chain (SC) is growing in terms of data, devices, users, and stakeholders, which introduced new security challenges and threats, especially with the reliance on centralized servers or cloud platforms. In addition, increased trust among system participants exposes the SC to a higher risk of vulnerabilities which require strong security measures. This article proposes a hybrid security framework for SC systems, BC-DRLzSC, that integrates Blockchain (BC) and Deep Reinforcement Learning (DRL) designed to operate in a zero trust (ZT) environment. In particular, we propose a decentralized BC-based approach integrated with smart contracts to manage system participant registration and authentication and to control access to system resources. BC-DRLzSC adopts a ZT architecture to reinforce SC security, which can be achieved with an advocate to verify each entity’s trustworthiness before granting or retaining access to system resources. Incorporating the ZT architecture, with BC and DRL, can potentially and significantly bolster SC system security. DRL is employed to develop a proactive attack detection model that continuously monitors the incoming traffic from authenticated nodes within the network and predicts any malicious actions. Finally, we evaluate the performance of our proposed DRL solution using the NSL-KDD dataset.

Artificial intelligence (AI) has emerged as a powerful tool for addressing the challenges posed by climate change and their impact on public health. By leveraging its capacity to analyze and predict climatic patterns, AI offers opportunities to enhance resource management and develop effective strategies for climate change mitigation. Moreover, AI can contribute to generating sustainable solutions that address the complex and interconnected nature of climate change. For example, AI can enable the optimization of energy consumption and facilitate the integration of renewable energy sources into existing systems. It can also support the development of climate models that provide timely and accurate predictions, enabling policymakers to implement proactive measures for disaster preparedness and response. Furthermore, AI-powered disease surveillance and mitigation techniques can improve public health outcomes by identifying patterns and trends in the spread of diseases in relation to climatic factors.However, the widespread adoption of AI-based solutions is not without challenges. Ethical concerns surrounding privacy and data ownership must be addressed, as the use of AI requires access to large datasets, raising potential privacy risks. Technical constraints, such as limited computational power and the need for sophisticated algorithms, also pose obstacles to the implementation of AI in climate change mitigation strategies. Furthermore, issues related to the accessibility and affordability of AI technologies must be resolved to ensure equitable distribution and maximize its potential impact on public health.To fully harness the power of AI in addressing climate change and improving public health outcomes, it is crucial to promote innovation, multidisciplinary collaboration, and open data science. Innovation can drive the development of new AI algorithms and technologies specifically tailored to address climate change challenges. Multidisciplinary approaches that bring together experts from diverse fields, including climate science, public health, and computer science, can foster a holistic understanding of complex systems and enable the design of comprehensive solutions. Finally, open data science practices, such as sharing data and algorithms, can facilitate collaboration and accelerate progress in mitigating climate change and its public health impacts.In conclusion, AI offers promising opportunities for effectively addressing climate change and its impact on public health. However, to fully realize its potential, it is essential to tackle ethical and privacy concerns, overcome technical constraints, and ensure accessibility and affordability. By promoting innovation, multidisciplinary collaboration, and open data science, we can unlock the transformative power of AI in mitigating climate change and improving public health outcomes.

This paper aims to address the exponential stability and stabilization problems for a class of delayed nonlinear Markov jump systems under randomly occurring Denial-of-Service (DoS) attack and packet loss. Firstly, the stochastic characteristics of DoS attack and packet loss are depicted by the attack success rate and packet loss rate. Secondly, a Period Observation Window (POW) method and a hybrid-input strategy are proposed to compensate for the impact of DoS attack and packet loss on the system. Thirdly, A Dynamic Event-triggered Mechanism (DETM) is introduced to save more network resources and ensure the security and reliability of systems. Then, by constructing a general common Lyapunov functional and combining with the DETM and other inequality analysis techniques, the less conservative stability and stabilization criteria for the underlying systems are derived. In the end, the effectiveness of our result is verified through a numerical example.

Recurrent pregnancy loss (RPL) affects around 2 % of women of reproductive age. Primary RPL is defined by ≥2 pregnancy losses and no normal birth delivery. In secondary RPL, the losses are after a normal pregnancy and delivery. Most cases have no clear aetiology, although primary cases are the most complex. Several gene polymorphisms have been associated with RPL. Some polymorphisms are increased in women of Asian or Caucasian race. In admixed RPL populations, the information on possible genetic links is scarce and contradictory. The study aimed to assess the frequency of two SNP in different enzymes involved in medical conditions observed during pregnancy. Microsomal epoxy hydrolase (mEPH) is involved in detoxifying xenobiotics. It is present in ovaries, and it is hormonally regulated. The endothelial nitric oxide synthase forms nitric oxide from arginine and is involved in vascular tone. Two SNPs, rs1051740 and rs1799983, were assessed. The study included 26 controls and 63 primary RPL patients. Significant differences were observed in the frequencies of both SNP (p<0.05). The frequency of mutated alleles was higher in patients. Double mutated homozygotes were encountered only in RLP patients (p<0.05). Genetic polymorphisms rs1051740 and rs1799983 may be involved in primary RPL in the Venezuelan admix population. Genetic studies could provide crucial information on the aetiology of primary RPL.

The conventional well placement was done manually by using a numerical reservoir simulator, and it required a lengthy trial-and-error process. It required great experience and expertise to manipulate the variables and uncertainties that lie on the reservoir to determine the best placement of the well. In addition, the traditional gradient-based methods such as Line-search and Trust-region were not viable in terms of maximum results obtained. Gradient-based methods were too dependent on the surface gradient of the solution and may only converge to local optima instead of global optima. Complex reservoirs have rough surfaces with high uncertainties, which hinders the traditional gradient-based method from converging to global optima. Thus, genetic algorithms were utilized to automate the manual trial-and-error process and to overcome the limitations of the traditional gradient-based method. The objectives of this study were to analyse the effect of different initial well placement distributions, the number of random solution sizes, and the crossover rate on cumulative oil production. A synthetic reservoir model built using CMG Builder was used as the testing platform for the optimization problems. Well-placement parameterization and optimization set-up were carried out using the CMG CMOST optimization tool. The integration of CMG IMEX and CMOST optimized cumulative oil production based on the objectives of the study. The results obtained showed that the higher number of random solutions used resulted in higher cumulative oil production, with more generations needed to reach the optimum solution. It can be concluded that the larger number of random solutions used increased the probability of reaching the optimum solution, but will take more generations.

The African continent has the highest prevalence of hypertension globally, with South Africa reporting the highest prevalence in Southern Africa. While the influence of genetic variability in the pathogenesis of hypertension is well described internationally, limited reports are available for African populations. This study aimed to assess the association of genetic variants and essential hypertension in a cohort of two ethnic South African population groups. Two hundred and seventy-seven hypertensive and one hundred and seventy-six normotensive individuals were genotyped for 79 variants. Genotyping was performed using the Illumina GoldenGate Assay and allele-specific polymerase chain reaction. The association of variants was assessed using the Fisher Exact test under the additive and allelic genetic models, while multivariate logistic regression was used to predict the development of hypertension. Five variants (CYP11B2 rs179998, AGT rs5051 and rs699, AGTR1 rs5186 and ACE rs4646994) were significantly associated with essential hypertension in the cohort under study. Furthermore, AGTR1 rs5186 and AGT rs699 were identified as risk factors for the development of hypertension in both ethnic groups. In two ethnic South African populations an association was observed between Renin-Angiotensin-Aldosterone System (RAAS) related genes and the development of hypertension.

The application potential of cellulosic materials in natural composites and other fields needs to be explored to develop innovative, sustainable, lightweight, functional biomass materials that are also environmentally friendly. This study investigated Typha augostifolia (Typha sp.) as a potential new raw material for extracting cellulose nanocrystals (CNCs) for application in wastewater treatment composites. Alkaline treatments and bleaching were used to remove cellulose from the stem fibers. The CNCs were then isolated from the recovered cellulose using acid hydrolysis. The study showed a few distinct functional groups (O-H, -C-H, =C-H and C-O, and C-O-C) in the Fourier Transform Infrared (FTIR) spectra. Scanning electron microscope (SEM) revealed the smooth surface of CPC and CNCs that resulted from removing lignin and hemicellulose from powdered Typha augostifolia. Based on the crystalline index, the powdered Typha augostifolia, CPC, and CNCs were 42.86%, 66.94% and 77.41%. The loss of the amorphous section of the Typha sp. fiber resulted in a decrease in particle size. It may be inferred from the features of a Typha sp. CNC that CNCs may be employed as reinforcement in composites for wastewater treatment.

As marine traffic is contributing to pollution and mostly have predictable route with repetitive load profiles, to reduce their impact on environment, hybrid system with proton exchange membrane fuel cells (PEMFC-s) and battery pack, is promising replacement. For this purpose, the numerical model of repowered existing vessel that have two diesel engines with 300 kWe is developed. The goal of this paper is to develop numerical model which analyzes and determine equivalent hybrid ship propulsion system for known traveling route. The developed numerical model consists of an interconnected system with PEMFC stack and battery pack as power sources. Numerical model is developed and optimized to meet minimal required power demand for successful route demand, which has variable loads and daily sails six-time same voyage- in total 54 nautical miles. The results have shown that equivalent hybrid power system consists of 300 kWe PEMFC stack and battery pack with 424 kWh battery and state of charge varying between 20 and 87%. To power this new hybrid power system, hydrogen tank of 7200 l holding 284.7 kg at pressure of 700 bar is needed, compared to previous system that spend 1524 kg of diesel and generate 4886 kg of CO2.

β-Ga2O3 is a well-known semiconductor material for power devices and other applications. Recently, β-Ga2O3 has also been reported as a scintillator material with a light yield of approximately 8400 ph./MeV, scintillation decay time of &lt;1 μs, and density of 6.44 g/cm3. In this study, 2-inch diameter β-Ga2O3 single crystals were prepared by oxide crystal growth using the cold crucible (OCCC) method under various oxygen partial pressures. In the OCCC method, as in the cold crucible method, a high frequency is applied directly to the oxide materials, which are heated and melted, and the melt is held by the outermost solid material itself that is cooled by water using a copper hearth. In the OCCC method, crystal growth is performed while rotating the seed crystal, as in the Czochralski method, to increase the crystal diameter. The optical properties and radiation responses of the crystals grown under various oxygen partial pressures were evaluated.

Ti and its alloys are the most commonly used materials for biomedical applications. However, bacterial infection after implant placement is still one of the significant rising complications. Therefore, the application of the antimicrobial agents into implant surfaces to prevent implant-associated infection has attracted lots of attention. Scientific papers have shown that inorganic antibacterial metal element (e.g. Ag, Cu, Zn) can be introduced to implant surfaces with the addition of metal nanoparticles or metallic compounds into electrolyte via micro-arc oxidation (MAO) technology. In this review, the effects of the composition and concentration of electrolyte and process parameters (e.g. voltage, current density, oxidation time) on morphological characteristics (e.g. surface morphology, bonding strength), antibacterial ability and biocompatibility of MAO antimicrobial coating were discussed in detail. Anti-infection and osseo-integration can be simultaneously accomplished with the selection of the proper antibacterial elements and operating parameters. Besides, MAO assisted by magnetron sputtering (MS) to endow Ti-based implant materials with superior antibacterial ability and biocompatibility was also discussed. Finally, the development trend of MAO technology in the future was forecasted.

In order to solve the problem of feature extraction of underwater acoustic signals in complex ocean environment, a new method for feature extraction from ship radiated noise is presented based on empirical mode decomposition theory and permutation entropy. It analyzes the separability for permutation entropies of the intrinsic mode functions of three types of ship radiated noise signals, and discusses the permutation entropy of the intrinsic mode function with the highest energy. In this study, ship radiated noise signals measured from three types of ships are decomposed into a set of intrinsic mode functions with empirical mode decomposition method. Then, the permutation entropies of all intrinsic mode functions are calculated with appropriate parameters. The permutation entropies are obviously different in the intrinsic mode functions with the highest energy, thus, the permutation entropy of the intrinsic mode function with the highest energy is regarded as a new characteristic parameter to extract the feature of ship radiated noise. After that, the characteristic parameters, namely, the energy difference between high and low frequency, permutation entropy, and multi-scale permutation entropy, are compared with the permutation entropy of the intrinsic mode function with the highest energy. It is discovered that the four characteristic parameters are at the same level for similar ships, however, there are differences in the parameters for different types of ships. The results demonstrate that the permutation entropy of the intrinsic mode function with the highest energy is better in separability as the characteristic parameter than the other three parameters by comparing their fluctuation ranges and the average values of the four characteristic parameters. Hence, the feature of ship radiated noise can be extracted efficiently with the method.

One of the tools for optimal crop production is regular monitoring and assessment of crops. During the growing season of fruit trees, the bloom period has increased photosynthetic rates that correlate with the fruiting process. This paper presents the development of an image processing algorithm to detect peach blossoms on trees. Images of an experimental peach orchard were acquired from the Parma Research and Extension Center of the University of Idaho using an off-the-shelf unmanned aerial system (UAS), equipped with a multispectral camera (Near-infrared, Green, Blue). The orchard has different stone fruit varieties and different plant training system. Individual tree images (high-resolution) and arrays of trees images (low-resolution) were acquired to evaluate the detection capability. The image processing algorithm was based on different vegetation indices. Initial results showed that the image processing algorithm could detect peach blossoms and demonstrate good potential as a monitoring tool for orchard management.

Fe-(9, 19, 28, 37)wt.% Cr alloys were corroded at 700 and 800 ^oC for 70 h under 1 atm of N₂, 1 atm of N₂/3.2%H₂O-mixed gas, and 1 atm of N₂/3.1%H₂O/2.42%H₂S-mixed gas. The corrosion rate of Fe-9Cr alloy increased with the addition of H₂O, and furthermore with the addition of H₂S in N₂ gas. Fe-9Cr alloy was always nonprotective. In contrast, Fe-(19, 28, 37) wt.%Cr alloys were protective in N₂ and N₂/H₂O-mixed gas because of formation of the Cr₂O₃ layer. They were, however, nonprotective in N₂/H₂O/H₂S-mixed gas because sulfidation dominated to form the outer FeS layer and the inner Cr₂S₃ layer containing some FeCr₂S₄.

Precision agriculture is a farm management technology that involves sensing and then responding to the observed variability in the field. Remote sensing is one of the tools of precision agriculture. The emergence of small unmanned aerial vehicles (sUAV) have paved the way to accessible remote sensing tools for farmers. This paper describes the comparison of two popular off-the-shelf sUAVs: 3DR Iris and DJI Phantom 2. Both units are equipped with a camera gimbal attached with a GoPro camera. The comparison of the two sUAV involves a hovering test and a rectilinear motion test. In the hovering test, the sUAV was allowed to hover over a known object and images were taken every second for two minutes. The position of the object in the images was measured and this was used to assess the stability of the sUAV while hovering. In the rectilinear test, the sUAV was allowed to follow a straight path and images of a lined track were acquired. The lines on the images were then measured on how accurate the sUAV followed the path. Results showed that both sUAV performed well in both the hovering test and the rectilinear motion test. This demonstrates that both sUAVs can be used for agricultural monitoring.

Based on some experiments, the paper describes with the help of polarization the physic-chemical processes that take place in the contact area of friction pairs, during the selective transfer as a result of the change in the input speed of the lubricant (glycerin), as well as how it influences their wear. Through polarization, the quantitative and qualitative transformations of glycerin are studied during frictional stress with selective transfer, the determination of the properties of the selective solution, and the damage to the metals and alloys of the friction pairs, but also after frictional stress.

Mineral nutrition is essential for plant growth and interaction of plants with biotic and abiotic stresses. Mango twig-tip dieback (MTTD) is a new type of mango decline, but its impact on the trees’ mineral nutrition is unknown. This study was conducted to determine the effect of MTTD infection on the nutrient status, balance, and resorption efficiency (RE) of mango. Leaf nutrient concentrations and deviation from the optimum percentage (DOP) indices of ‘Kensington Pride’ (KP) mango trees with low (LD) and high (HD) levels of MTTD infections were analyzed to compare the foliar nutrition status and nutrient balance between the LD and HD trees. Moreover, the nutrient resorption efficiency of MTTD-infected dried leaves (RE_D) was compared with the resorption efficiency of healthy (RE_S) leaves of KP mangoes. The concentrations of the total Ca, Mg, Cu, Fe, Mn, and Zn were lower in the HD trees than in the LD trees. But the total K content was higher in the HD trees, and its DOP index was sufficient, while the total K concentration was low and deficient level in LD trees. Moreover, DOP indices for total Ca, Mn, and Zn were less deficient in LD trees than in HD trees, and overall nutrient imbalances were exacerbated in HD trees. RE_D was significantly lower than RE_S for the total N, P, S, Cu, Fe, and Zn but significantly higher than RE_S for K. The study underscores the significant influence of MTTD on the mineral nutrition of KP mangoes, revealing distinct nutrient variations between trees with low and high MTTD infection levels. These findings have important implications for mango crop management, emphasizing the need for targeted nutrient interventions to address imbalances induced by MTTD and enhance the overall health and resistance of mango trees against MTTD infection.

. Protein cysteine S-glycosylation is a relatively rare and less well characterized post-translational modification (PTM). Creating reliable model proteins that carry this modification is challenging. The lack of available model or natural S-glycosylated proteins significantly hampers the development of MS-based methodologies for detecting protein cysteine S-glycosylation in real-world proteomic studies. There is also limited MS-sequencing data describing easier to create synthetic S-glycopeptides. Here, we present the results of an in-depth manual analysis of automatically annotated CID/HCD spectra for model S-glucopeptides. The CID spectra show a long series of y/b-fragment ions with retained S-glucosylation, regardless of the dominant m/z signals corresponding to neutral loss of 1,2-anhydroglucose from the precursor ions. In addition, the spectra show signals manifesting glucosyl transfer from the cysteine position onto Lys, Arg side chains, and a peptide N-terminus. Other spectral evidence indicates that the N-glucosylated initial products of transfer are converted into N-furanosylated (i.e., glycated) structures due to Amadori rearrangement. We discuss the peculiar transfer of the glucose oxocarbenium ion (Glc+) to positively charged guanidinium residue (ArgH+) and propose a mechanism for the gas-phase Amadori rearrangement involving a hydride ion shift.

We study L_2-approximation problems in the weighted Hilbert spaces in the worst case setting. Three interesting weighted Hilbert spaces appear in this paper, whose weights are equipped with two positive parameters $\ga_j$ and $\az_j$ for $j=1,\,2,\dots,\,d$. We consider the worst case error of algorithms that use finitely many arbitrary continuous linear functionals. We discuss the exponential convergence-(t,s)-weak tractability (EC-(t,s)-WT) of these L_2-approximation problems under the absolute or normalized error criterion. In particular, we obtain the sufficient and necessary conditions for EC-(1,1)-WT and EC-(t,1)-WT with t

In (Semigroup Forum 77: 325-338, 2008) Mahmoudi M. and Renshaw J. solved a study that covers of cyclic $S$-acts over monoids. This article is an attempt to initiate the covers of finitely generated $S$-acts. We give a necessary and sufficient condition for a monoid to have the properties that $n$-generated $S$-acts have strongly flat covers, Condition $(P)$ covers and projective covers. The main conclusions extend some known results. We show also that Condition $(P)$ covers of finitely generated $S$-acts are not unique, unlike the situation for strongly flat covers. Additionally, we demonstrate that the property of Enochs' $\mathcal{X}$-precover of $S$-act $A$, where $\mathcal{X}$ denotes a class of $S$-acts that are closed under isomorphisms.

The study of the tribological behavior of the braking system in auto vehicles requires knowing the characteristics of the material in contact and, in the work process, for the friction pair, brake disc-pads. Materials structural analysis is necessary because the wear process depends on the friction pair chemical composition, and brake disk-pads, respectively on the work process parameters (pressing force, rotational speed, traffic conditions, etc.). The material of the brake discs is generally the same gray cast iron, but the brake pads can be semi-metallic (particles of steel, copper, brass, and graphite, all united with a special resin), organic materials (particles of rubber, glass, and kevlar all joined with the help of a resin), composite materials that contain different constituents and ceramic materials (rarely have small copper particles). Therefore, the purpose of the paper is to know the crystalline structure and the mechanical properties of the brake pad materials, through specific studies and analyses, with important implications on the friction and wear behavior.

Quantitative analysis of human gait is critical for early discovery, progressive tracking, and rehabilitation of neurological and musculoskeletal disorders, such as Parkinson’s Disease, stroke, and Cerebral Palsy. Gait analysis typically involves estimating gait characteristics, such as spatio-temporal gait parameters and gait health indicators (e.g., step time, length, symmetry, and balance). Traditional methods of gait analysis involve the use of cameras, wearables, and force plates, but are limited in operational requirements when applied in daily life - such as direct line-of-sight, carrying devices, and dense deployment. This paper introduces a novel approach for gait analysis by passively sensing footstep-induced floor vibrations during walking using vibration sensors mounted on the floor surface. Our approach is non-intrusive, scalable, and perceived as more privacy-friendly, making it suitable for continuous gait health monitoring in daily life. We developed a floor vibration-based gait analysis framework to estimate various gait parameters that are used as standard metrics in medical practices, including temporal parameters (step, stride, stance, swing, double-support, single-support time) and spatial parameters (step length, width, angle, stride length), and extracts gait health indicators (cadence/walking speed, left-right symmetry, gait balance, initial contact types). The main challenge is that floor vibrations are distinct across different floor types. To address this challenge, our approach develops floor-adaptive algorithms to extract floor-specific features and is designed to be generalizable to various settings, including homes, hospitals, and eldercare facilities. We evaluate our approach through real-world walking experiments with 20 adults with 12,231 labeled gait cycles across concrete and wooden floors. Our results show 90.5% (RMSE 0.08s), 71.3% (RMSE 0.38m), and 92.3% (RMSPE 7.7%) accuracy in estimating temporal, spatial parameters, and gait health indicators, respectively.

Bartonella species, intracellular parasitic zoonotic pathogens, has drawn increasing attention for their diverse host range and associated human diseases. This study investigates Bartonella infection in small mammals in Yunnan Province, China, focusing on tissue tropism. 333 small mammals were sampled from 13 species, 3 orders, 4 families, and 4 genera in Heqing and Gongshan Counties. Conventional PCR and real-time quantitative PCR (qPCR) were utilized for detection and quantification, followed by bioinformatic analysis of obtained DNA sequences. Results show a 31.5% detection rate, varying across species. Notably, Apodemus chevrieri, Eothenomys eleusis, Niviventer fulvescens, Rattus tanezumi, Episoriculus leucops, Anourosorex squamipes, and Ochotona Thibetana exhibited infection rates of 44.4%, 27.7%, 100.0%, 6.3%, 60.0%, 23.5%, and 22.2%, respectively. Genetic analysis identified 30, 10, and 5 strains based on ssrA, rpoB, and gltA genes, with nucleotide identities ranging from 92.1% to 100.0%. Bartonella strains were assigned to B. grahamii, B. rochalimae, B. sendai, B. koshimizu, B. phoceensis, B. taylorii, and a new species identified in the Episoriculus leucops (GS136). Tissue distribution analysis revealed varied copy numbers across different tissues, with the highest load in spleen. These findings underscore Bartonella's diverse species and host range in Yunnan Province, highlighting its broad tissue tropism in small mammals.

Background: The incidence of various types of cancer, for example papillary thyroid carcinoma (PTC), is on the rise. Since therapeutic success depends greatly on early diagnosis, reliable diag-nostic biomarkers must be identified and easy-to-apply tools for detecting them must urgently be standardized. Here, we contribute to solving this medical challenge by assessing miRNAs sus-pected of promoting carcinogenesis in extracellular vesicles (EVs) that can be routinely obtained via liquid biopsy. We profit from current progress in cancerology that provides innovations in liquid biopsy and EVs analysis along with identification of miRNAs and chaperone system (CS) components implicated in carcinogenesis. Methods: We measured in EVs obtained from circulat-ing blood plasma from PTC patients the levels of three miRNAs implicated in thyroid cancer, miR-1, miR-206, and miR-221, and most likely involved in the regulation of two members of the CS, Hsp60 and CCT. EVs were isolated from the plasma of patients with PTC and controls with benign goiter (BG), and from the culture medium of a PTC cell line (MDAT32) and were duly characterized. Results: The levels of miRNAs determined by RT-qPCR were consistently higher in PTC patients and decreased down to control levels after thyroidectomy. Bioinformatics showed that the miRNAs target genes were associated to the molecular pathogenesis of PTC. Conclusions: Thus, our exploratory study reaffirms the potential in clinics of the selected miRNAs in EVs as useful biomarkers of PTC easily accessible via liquid biopsy, which is minimally invasive and amenable to periodic repetition, an improvement compared to the established fine-needle aspirate biopsy.

PURPOSE: To investigate the oxylipin profiles in aqueous humor of primary open angle glaucoma (POAG) patients. METHODS: Aqueous humor samples were collected from 17 POAG patients and 15 cataract subjects and subjected to the liquid chromatography-mass spectrometry (LC-MS) analysis to detect the oxylipins. The prediction potential of the differential abundant oxylipins was assessed by the receiver operating characteristic (ROC) curves. Pathway and correlation analyses on the oxylipins and clinical and biochemical parameters were also conducted. RESULTS: The LC-MS analysis detected a total of 76 oxylipins, of which 29 oxylipins reached the detection limit. The multivariate analysis identified 5 differential abundant oxylipins, 15-keto-prostaglandin F2 alpha (15-kPGF2α), Leukotriene B4 (LTB4), 12,13-Epoxyoctadecenoic acid (12,13-Epome), 15-Hydroxyeicosatetraenoic acid (15-HETE) and 11-Hydroxyeicosatetraenoic acid (11-HETE). The 5 oxylipins are enriched in the arachidonic acid metabolism and linoleic acid metabolism pathways. Pearson correlation analysis showed that 11-HETE was positively correlated with intraocular pressure and central corneal thickness and negatively with cup/disk ratio in the POAG patients. In addition, 15-kPGF2α was positively correlated with visual field defect, and LTB4 was negatively correlated with macular thickness.  CONCLUSIONS: This study revealed the oxylipin profile in the aqueous humor of POAG patients. Oxylipins involved in arachidonic acid metabolism pathway could play a role in POAG and anti-inflammatory therapies could be potential treatment strategies for POAG.

Regardless of the SARS-CoV-2 pandemic containment, it remains paramount to comprehensively understand its underlying mechanisms to mitigate potential future health and economic impacts, comparable to those experienced throughout the course of the pandemic. The angiotensin-converting enzyme 2 (ACE2) provide anchorage for SARS-CoV-2 binding, thus implicating that ACE and ACE2 might contribute to the variability in infection severity. This study aimed to elucidate predisposing factors influencing the disease course among people infected by SARS-CoV-2, focusing on angiotensin-converting enzyme (ACE) and ACE2 polymorphisms. Notably, despite similar demographics and comorbidities, COVID-19 patients exhibit substantial differences in prognosis. Genetic polymorphisms in ACE and ACE2 have been implicated in disease progression, prompting our investigation into their role in COVID-19 evolution. Using next-generation sequencing (NGS), we analyzed ACE and ACE2 genes in a sample group comprising six subjects infected by SARS-CoV-2. Our findings revealed a correlation between specific polymorphisms and COVID-19 outcomes. Specifically, ACE and ACE2 intronic deletions were observed in all deceased patients, suggesting a potential association with mortality. These results highlight the significance of genetic factors in shaping the clinical course of COVID-19, emphasizing the importance of further research into the impact of genetic variations on COVID-19 severity.

Chaga (Inonotus obliquus) is a pathogenic fungus that grows mostly on birch species (Betula pendula and B. pubescens) and has traditionally been used as an anti-cancer medicine. The study aimed to compare the chemical composition and cytotoxic activity of chagas growing on both Betula spp. on various cancer cell lines. The freeze dried extracts contained triterpenes inotodiol, lanosterol betulin and betulinic acid typical to conks growing on Betula species. The cytotoxic activity of chaga growing on Betula pendula and B. pubescens 80% ethanolic extracts against thirty-one human cancer cell lines has been evaluated by a sulforhodamine B assay. The strongest inhibitions were observed with chaga (growing on B. pendula) extract on the HepG2 and CAL-62 cell line, and with chaga (from B. pubescens) extract on HepG2 cell line, with IC50 values of 37.71, 43.30, and 49.99 μg/mL, respectively. The chaga extracts from B. pendula exert somewhat stronger effects on most cancer cell lines studied than B. pubescens extracts. This study highlight the potential of chaga as a source of bioactive compounds with selective anti-cancer properties, encouraging further exploration of its therapeutic mechanisms and potential applications in cancer treatment.

In the present study, a multilayer high barrier thin blown film based on a polybutylene adipate terephthalate (PBAT) blend with polyhydroxyalkanoate (PHA), and composed of four layers, including a cellulose nanocrystals (CNC) barrier layer and an electrospun poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) hot-tack layer, was characterized in terms of surface roughness, surface tension, migration, mechanical and peel performance, barrier properties and disintegration rate. The results showed a material with a smooth surface. The overall migration test showed that the material was suitable for its use as a food contact layer. The addition of the CNC interlayer had a significant effect on the mechanical properties of the system, drastically reducing the elongation at break and, thus, the flexibility of the material. However, the material retained its elastic modulus and tensile strength. The CNC coating had a negative impact on the peeling strength, weakening the inherently strong interlayer adhesivity of the electrospun PHBV fibers. The multilayer had a good barrier to water vapor, and especially to oxygen, with its permeance reduced by up to a 90 % when the CNC layer was present. Finally, the monolayer blend film disintegrated in a period of less than 55 days in a laboratory-scale composting experiment, while the multilayer system disintegrated in 60 days. Overall, the multilayer system formed a fully compostable structure with great potential for use in food packaging applications.

(1) Background: Food waste (FW) in Romania is 70 Kg/capita/year, while 70% of food waste comes from public catering, retail services, and households (over 50% – 47 million tons). (2) Methods: A cross-sectional observational study was conducted using an online questionnaire via the Google Forms platform from 15 April 2023 to 15 May 2023. The questionnaire was designed to assess various aspects, such as some socio-demographic information (age, sex, occupation, area of residence, study level, household members number, children &lt; 18 years of age); the personal involvement and frequency of food purchases and homemade food cooking; the main sources that generate food waste; the motivation and frequency with which food waste occurs; the level of awareness regarding the impact of food waste; the respondents' intentions regarding sustainable behaviors and practices food management; the level of information and familiarity of the respondents with the notions of validity and how these may influence their food consumption decisions. (3) The results show that FW incidence is occasionally (42%), very rarely (43.33%), frequently (15%), and no food waste was reported by 2.66% of respondents. The [35-44] age category records the highest FW frequency, followed by [18-24]. The most wasted are homemade food (29.67%), bread and bakery products (27.00%), and fruits and vegetables (14.33%). High involvement in purchasing and buying food following a previously established list reduces FW frequency. The same is valid for high daily involvement in food and homemade cooking. High interest in the FW problem and its perception as a waste of money leads to diminishing it, while guilty feelings increase the FW level (37.50% to 73.33%). (4) Conclusions: The present study shows that household food waste management is a multifactorial process that involves numerous socio-demographic, behavioral, and emotional aspects. Extensive data analysis supports our results, revealing deep self-reported information details and confirming its complex approach.

The planar cell polarity (PCP) of epithelial ciliated cells is essential for effective mucociliary clearance (MCC) in the sinonasal mucosa. We hypothesize that MCC coordination is impaired in nasal polyp (NP) mucosae due to suppressed expression of a series of CPLANE (ciliogenesis and planar cell polarity effector) complex proteins in chronic rhinosinusitis (CRS) patients. To inves-tigate this hypothesis, we subjected sinonasal mucosal samples to live video recording to measure mucociliary transport velocity (MCTV) and scanning electron microscopy to evaluate surface morphology. The expression and distribution of a panel of PCP proteins, e.g. WDPCP and FUZ, were investigated in relation to inflammatory cytokine levels and clinical features. The mean MCTV of NP mucosae was significantly lower than that of the inferior turbinate mucosae. The CRS group with NPs (CRSwNP group) (n=28) showed increased expression of IL-13 and CCL26 mRNA compared to CRS patients without NPs (n=25) and controls (n=30). WDPCP and FUZ mRNA levels were significantly decreased in NP mucosae compared to ethmoid sinus mucosae in CRSwNP patients. WDPCP protein distribution was reduced in the cytoplasmic region of ciliated cells in CRSwNP patients. We conclude that suppression of WDPCP in ciliated cells is responsible for the impaired MCC of nasal polyps with type-2 inflammation. This mechanism might explain the decreased clearance and the potential for worsening symptoms of CRSwNP.

Athlete’s heart is characterised by structural, functional, and electrical remodelling. During an exercise session, the heart increases the use of oxygen, which is associated with decreased vascular resistance in the lungs’ circulation. Left ventricular hypertrophy is an echocardiographic modification especially met in endurance athlete’s heart. Moreover, left atrial dilatation represents another important characteristic of endurance athletes. Electrical modulation in the athletic heart induces neurological modifications leading to sinus arrhythmia, bradycardia, early repolarisation, and first-grade atrioventricular (AV) blocks. Athletes' nutritional status involves the assimilation of macronutrients such as proteins, carbohydrates, and fats. Depending on the duration of physical exercise, ATP can be obtained in aerobic or anaerobic conditions. This systematic review aims to find correlations between different evaluative methods of cardiac adaptation and present the metabolism in performance athletes.

Contamination in coastal regions attributed to fluoride and nitrate cannot be disregarded, given the substantial environmental and public health issues they present worldwide. Maintaining water quality is crucial for environmental well-being. This comprehensive study was performed to assess the spatial as well as indexical water quality, identify contamination sources, and evaluate associated health risks pertaining to nitrate and flouride in AlHassa region, KSA. The physiochemical results revealed a pervasive pollution of the overall groundwater. The dominant water type was Na-Cl, indicating saltwater intrusion and reverse ion exchange impact. Spatiotemporal variations in physicochemical properties suggest diverse hydrochemical mechanisms, with geogenic factors primarily influencing groundwater chemistry. The groundwater pollution index varied between 0.8426 and 4.7172, classifying samples as moderately to very highly polluted. Similarly, the synthetic pollution index (in the range of 0.5021-4.0715) revealed that none of the samples had excellent water quality, with various degrees of pollution categories. Nitrate Health Quotient (HQ) values indicated chronic human health risks ranging from low to severe, with newborns being the most vulnerable. Household use of nitrate-rich groundwater for showering and cleaning did not pose significant health risks. Fluoride HQ decreased with age, and children faced the highest risk of fluorosis. The Hazard Index (HI) yielded moderate to high-risk values. Nitrate risks were 1.21 times higher than fluoride risks, as per average HI assessment. All samples fell into the vulnerable category based on the Total Hazard Index (THI), with 88.89% classified as very high risk. This research provides valuable insights into groundwater quality, guiding water authorities, inhabitants, and researchers in identifying safe water sources and vulnerable human populations. The results highlight the need for appropriate treatment techniques and long-term coastal groundwater management plans.

Background: Leishmaniasis is a significant global public health issue that is caused by parasites from Leishmania genus. With limited treatment options and rising drug resistance, there is a pressing need for new therapeutic approaches. Molecular chaperones, particularly Hsp90, play a crucial role in parasite biology and are emerging as promising targets for drug development. Objective: This study evaluates the efficacy of 17-DMAG in treating BALB/c mice from cutane-ous leishmaniasis through in vitro and in vivo approaches. Materials and Methods: We assessed 17-DMAG cytotoxic effect on bone marrow-derived mac-rophages (BMMΦ) and its effects against L. braziliensis promastigotes and intracellular amastigotes. Additionally, we tested the compound's efficacy in BALB/c mice infected with L. braziliensis via intraperitoneal administration to evaluate the reduction of lesion size and de-crease of parasite load in the ears and lymph nodes of infected animals. Results: 17-DMAG showed selective toxicity [selective index=432) towards Leishmania amastigotes, causing minimal damage to host cells. The treatment significantly reduced lesion sizes in mice and results in parasite clearance from ears and lymph nodes. It also diminished in-flammatory responses and reduced the release of pro-inflammatory cytokines (IL-6, IFN-g, TNF) and the regulatory cytokine, IL-10, underscoring its dual leishmanicidal and anti-inflammatory properties. Conclusion: Our findings confirm the potential of 17-DMAG as a viable treatment for cutaneous leishmaniasis and support further research into its mechanisms and potential applications against other infectious diseases.

The discharge of industrial effluents containing toxic heavy metals in water sources has serious consequences for human health and the environment, and biosorption appears to be an environmental-friendly and cost-effective alternative that can be used for wastewater treatment. The use of different types of agricultural waste as biosorbents for the removal of toxic heavy metals, although an alternative, is quite difficult to apply in practice because these wastes have many other uses. Based on these considerations, in this study, soybean biomass (SB), soybean waste biomass obtained from oil extraction (SBW) and biochar obtained from soybean waste pyrolysis (BC-SBW) were testes as biosorbents form the removal of Pb(II) and Cd(II) ions, in batch systems. Under optimal conditions (pH = 5.4, 4.0 g biosorbent/L, room temperature (25 ± 1 C), contact time = 180 min), the biosorption capacity increase in the order: SB &lt; SBW &lt; BC-SBW for both metal ions, indicating that BC-SBW has the highest efficiency in removing toxic heavy metals. In addition, experiments on wastewater samples have shown that, in addition to significant reducing the content of heavy metals, BC-SBW also significant improved other quality indicators (such as: pH, TSM, CCO-Cr, CBO5), compared to the other biosorbents (SB and SBW). Quantitative evaluation of the biosorptive performance of each biosorbent (SB, SBW and BC-SBW) shows that BC-SBW has a real chance of being used on an industrial scale for wastewater treatment. All these aspects allowed the development of a circular approach for the use of soybean biomass in the removal processes of toxic heavy metals. This approach minimizes the shortcomings of using biomass as a biosorbent and increase the chance of using these materials in industrial practice.

The nuclear magnetic resonance (NMR) metabolomic analysis was applied to investigate the differences within nineteen Sicilian Nocellara del Belice mono varietal Extra Virgin Olive Oils (EVOO), grown in two zones different for altitude and soil composition. Several classes of endogenous olive oil metabolites were quantified through a nuclear magnetic resonance (NMR) three-experiment protocol coupled with a yet developed data-processing called MARA-NMR. This method, taking around one-hour experimental time per sample, faces the possible quantification of different class of compounds at different concentration’s range which would require at least three alternative traditional methods. NMR results were compared with the data of traditional analytical methods to quantify free fatty acidity (FFA), fatty acid methyl esters (FAMEs), and total phenol content. The presented NMR methodology is compared with traditional analytical practices and its consistency is also tested through slightly different data treatment. Despite the rich literature about the NMR of EVOOs, the paper points out that there are still several advances potentially improving this general analysis and overcoming the other cumbersome and multi-devices analytical strategies. Monovarietal EVOO’s composition is mainly affected by pedoclimatic conditions in turn relaying upon the nutritional properties, quality, and authenticity. Data collection, analysis and statistical processing are discussed touching the important issues related to the climate changes in Sicily and to the specific influence of pedoclimatic conditions.

Acute myocardial infarction (AMI) results from vulnerable plaque rupture, causing ischemic cardiomyocyte necrosis and intense inflammation. Paradoxically, this inflammation releases factors that aid heart repair. Recent findings suggest a role for extracellular vesicles (EVs) in intercellular communication during post-AMI cardiac repair. However, EVs’ tissue origin and chemokine profile in the blood of patients with AMI remains unclear. This study characterized EV tissue origin and chemokine receptor profile in the coronary and peripheral blood of patients with AMI. The results reveal that vesicles isolated from coronary and peripheral blood plasma are enriched in tetraspanin (CD9) and express CD81+, CD90+, and CD144+. The vesicle size ranged between 145 and 162 nm, with the control group exhibiting smaller vesicles than the AMI group. Furthermore, all vesicles expressed CCR6+ and CXCR3+, whereas a small percentage expressed CCR4+. In addition, a decrease in CXCR3+ and CCR6+ positivity was observed in coronary and peripheral blood vesicles compared with the control. Non-difference was found in the coronary and peripheral blood for the CXCR3+ and CCR6+ markers. In conclusion, our study demonstrates, for the first time, changes in the number of extracellular vesicles expressing CD144+, CXCR3+, and CCR6+ in the peripheral circulation of patients with AMI. Extracellular vesicles present in the peripheral circulation of patients with AMI hold excellent promise as a potential diagnostic tool.

Several studies with kaempferol (KP) and linearolactone (LL) have shown antiparasitic activities. However, the toxicity of treat-ments with both active principles is unknown. Therefore, this study aimed to evaluate the toxicological effects of treatments with KP and LL on the amoebic liver abscess (ALA) model in M. auratus administered intraperitoneally (i.p.). For this, ALA in-duction was carried out in male hamsters with 1.5 x105 E. histolytica trophozoites inoculated in the left hepatic lobe. The lesion evolved for four days and the i.p. of the treatments with KP (5 mg/kg body weight/day) and LL (10 mg/kg body weight/day) was carried out for four consecutive days. For histopathological evaluation, NMR studies, paraclinical analysis, and necropsy were performed. The results revealed that the inhibition of ALA by KP and LL were similar to that metronidazole (MTZ). Biochemical parameters revealed hepatic and renal alterations in all treatment groups, mainly for KP (AST and BUN). The lesions found in the organs were those that are directly linked to the pathology. In conclusion, KP and LL decrease ALA development but have few toxicological effects. Both compounds combined with MTZ could be therapeutic alternatives for amoebiasis caused by E. histolytica.

Oritavancin is a novel long-acting lipoglycopeptide with in vitro activity against methicillin-resistant (MR) Gram-positive pathogens and a good bactericidal activity even in presence of biofilm forming bacteria. It has been approved for acute bacterial skin and skin structure infections (ABSSSI), but recent reports have demonstrated possible off-label uses, as for prosthetic joint infections (PJI), which, in more than half of cases, are caused by MR Gram positive organisms. We reported a case of a man in his eighties with a late shoulder PJI caused by methicillin resistant Staphyloccus epidermidis (MRSE) with contraindications for surgical replacement and few oral therapeutic options for a long term suppressive antibiotic therapy. The prosthesis was retained, and the patient received ten outpatient sequential doses of 1200 mg of oritavancin during 28 weeks, based on therapeutic drug monitoring (TDM) as a guide for correct timing of administration of each dose. During oritavancin administration, the patient achieved clinical cure, with disappearance of the pain and regaining pre-infection joint mobility, with no side effects reported and no further surgery or hospitalization needed. The treatment is ongoing as a long-lasting suppressive antimicrobial therapy. Oritavancin could represent an excellent solution for treating PJI caused by MR organism, especially in patients who need a long-term suppressive therapy.

During 2021 and 2022 summers, we measured the total and dissolved (&lt; 0.45 mm) concentration of 25 elements in Utah Lake using Inductively Coupled Plasma Optical Emission Spectrometry (ICP-OES). Utah regulates twelve of these elements. ICP-OES sensitivity is at the ppb-level but is not the approved regulatory method. All regulations are for dissolved concentrations; except aluminum (Al) and phosphorus (P) which are for total recovery. We found total Al concentrations above allowable, but dissolved concentrations were well below allowable concentrations. We attribute high total concentrations to suspended clays. Dissolved copper (Cu) concentrations were below regulatory levels in 2021, but some samples were above regulatory levels in 2022. This could be related to the use of Cu-based algaecide treatments, or from other sources. Lead (Pb) data were inconclusive; dissolved Pb concentrations were well below the acute (1-hour average) limit, but the chronic concentration limit (4-hour average) is below the ICP-OES minimal detection limit. Arsenic (As) concentrations exhibit a seasonal trend that we attribute to groundwater inflows. This ppb-level study provides insight into regulated elements in Utah Lake previously not available due to the high sensitivity of the method and measurements of both total and dissolved concentrations.

Liver fibrosis, a consequence of chronic liver damage or inflammation, is characterized by the excessive buildup of extracellular matrix components. This progressive condition significantly raises the risk of severe liver diseases like cirrhosis and hepatocellular carcinoma. The lack of approved therapeutics underscores the urgent need for novel anti-fibrotic drugs. Hepatic stellate cells (HSCs), key players in fibrogenesis, are promising targets for drug discovery. This study investigated the anti-fibrotic potential of Citrus hystrix DC. (KL) and its bioactive compound, β-citronellol (β-CIT), in a human HSC cell line (LX-2). Cells exposed to TGF-β1 to induce fibrogenesis were co-treated with crude KL extract and β-CIT. Gene expression was analyzed by Real-Time qRT-PCR to assess fibrosis-associated genes (ACTA2, COL1A1, TIMP1, SMAD2). The releasing of matrix metalloproteinase 9 (MMP-9) was measured by ELISA. Proteomic analysis and molecular docking identified potential signaling proteins and modeled protein-ligand interactions. Results showed that both crude KL extract and β-CIT suppressed HSC activation genes and MMP-9 levels. The MAPK signaling pathway emerged as a potential target of β-CIT. This study demonstrates the ability of KL extract and β-CIT to inhibit HSC activation during TGF-β1-induced fibrogenesis, suggesting a promising role of β-CIT in anti-hepatic fibrosis therapies.

The terpolymers of N-vinylpyrrolidone (VP) with acrylic acid and triethylene glycol methacrylate were synthesized with more than 90% yield by radical copolymerization in ethanol from monomeric mixtures of different composition (98 : 2 : 2, 95 : 5: 2 and 98 : 2: 5). Their physical and chemical characteristics such as monomer composition, absolute molecular masses and hy-drodynamic radii in aqueous media at different temperature were determined. The temperature effect on the behavior of terpolymers in water and aqueous saline buffer solution with pH 7.4 has been studied and the ability of a copolymer enriched with dimethacrylates units was discovered to respond to a temperature change in these media. On the basis of terpolymers and linear polyvi-nylpyrrolidone (PVP), polymer compositions of hydrophobic dye methyl pheophorbide a, MPP, that is fluorescent in the red region of the spectrum, were obtained; the sizes of the polymer nanostructures of MPP in water were determined. The structures based on terpolymers were demonstrated to be more stable than MPP-PVP ones. It was carried out the quantum-chemical modelling of the possible structures of MPP-copolymer that formed as a result of intermolecular interaction between MPP and terpolymer’s chains; the possibility of the formation of hydrogen bonds between the donors of the electrons of terpolymer units and the proton donors of the MPP molecule was shown. Using the MTT test, it was established that copolymers of various compositions are low toxic for non-tumor Vero cells and HeLa tumor cells. It was shown that the cytotoxicity of polymer particles loaded with MPP for FetMSC and HeLa cells increased. Using fluorescence microscopy, the accumulation and distribution of polymer particles in non-tumor (FetMSC) and tumor (HeLa) cells was studied and an increase in the accumulation of MPP with both types of particles was shown.

Background: Study to assess glucose levels of people with type 1 diabetes (T1D) overnight based on insulin type and timing. Methods: Real-world, retrospective study in T1D using multiple daily insulin injections. Contin-uous glucose monitoring and insulin injections data were collected for ten hours after dinner us-ing the Insulclock® connected cap. Meal events were identified using ROC detection methodology. The timing of rapid insulin, second injections, and the type of insulin analogs used were evaluat-ed. Results: Nocturnal profiles (n=775, 49 subjects) were analyzed. Higher glucose AUC over 180mg/dL was observed in delayed injections (number; %; mg/dL x h): -45-15min (n=136; 17.5%, 175.9 ±271.0); -15-0min (n= 231; 29.8%, 164.0 ±237.1); 0+45min (n= 408; 52.6%, 203.6 ±260.9), (p 0.049). The use of ultrarapid (FiAsp®) (URI) vs rapid insulin analogs (RI) was associated with less hypoglycemia events (7.1 vs 13.6%; p 0.005) and TBR70 (1.7 +6.9 vs 4.6 +13.9%; p 0.003). Us-ers of glargine U300 vs degludec had higher TIR (70.7 vs 58.5 %) (Adjusted R-squared: 0.22, p < 0.001). The use of a correction injection (n= 144, 18.6%) was associated with higher hypoglycemia events (18.1 vs 9.5%; p 0.003), TBR70 (5.5 +14.2 vs 3.0 +11.1%; p 0.003), glucose AUC over 180 mg/dL (226.1 +257.8 vs 178.0 +255.3 mg/dL x h; p 0.001), and lower TIR (56.0 +27.4 vs 62.7 +29.6 mg/dL x h; p 0.004). Conclusions: Dinner rapid insulin timing, insulin types and correction injections affect nocturnal glucose profile in T1D.

Solar pasteurization, as a means of treating milk in remote rural areas without electrical power, is based on using solar energy to thermally inactivate pathogenic microorganisms at temperatures below the boiling point to maintain or improve milk quality. A solar milk pasteurizer of flat‐plate water‐heating glass acting as the solar collector, connected to a stainless-steel cylindrical milk vat, was constructed and evaluated in Navrongo, in the tropical savanna zone of Ghana, West Africa. The novel approach taken in this project is to integrate the solar collection and heat exchanger into a single unit using materials and fabrication techniques readily available in the developing world. The vat comprises a 1.5 mm thick stainless steel cylindrical tank, a 2.2 cm wide hot water jacket, and an outer layer of 5.0 mm thick aluminium foil insulation. Hot water produced by the collector was used for pasteurizing milk. The optimum quantity of milk that this device could pasteurize under the study conditions was 8 L. The device could pasteurize raw milk to a maximum temperature of 74 °C at 14:00 h GMT. The ambient temperature during the pasteurization ranged from 30 °C to 43 °C. The microbial analysis before and after the pasteurization was done, and the result shows that the total bacteria count before pasteurization was 6.6x10⁶ log CFU/mL per unit volume, and the total bacteria count after pasteurization was 1.0x10² log CFU/mL. By acceptable standards, the total bacteria count after pasteurization is within a safe range for consumption, and coliform counts were negative. The solar milk pasteurization system is cost-effective. Hence, it is appropriate for milk producers in arid pastoral areas without electricity to adopt the solar pasteurizer as an alternative to firewood as a fuel source for milk pasteurization. This approach can potentially create a cottage industry that may also play a crucial role as a water treatment technology that will improve the health of rural populations.

The yak (Poephagus grunniens) has evolved unique adaptations to survive the harsh environment of the Tibetan Plateau, while their gut microorganisms play a crucial role in maintaining the health of the animal. Gut microbes spread through the animal population not only by horizontal transmission but also vertically, which enhances microbial stability and inheritance between generations of the population. Homogenization of gut microbes in different animal species occurs in the same habitat enhancing interspecies coexistence. Using the yak as a model animal, this paper reviews the adaptive strategies under extreme environments and how the gut microbes of the yak circulate throughout the Tibetan Plateau system, which not only affects other plateau animals such as plateau pikas, but can also have a profound impact on the health of people. By examining the relationships between yaks and their gut microbes, this review provides new perspectives in understanding the adaptations of plateau animals and the stability of the ecosystem.

In order to cope with the limited supply of feed for global animal production, there is a pressing need to explore alternative feed resources. Orange pulp, a by-product of agriculture and industry, has shown potential to positively or neutrally impact pig productive performance when included in their diet. However, there is a lack of research on the effects of fermented navel orange pulp (FNOP) on pig growth and productive performance. This study aimed to investigate the effects of FNOP as a dry matter substitute on pig’s growth performance, carcass characteristics, meat quality, meat nutrition, and serum biochemical indicators. The experiment involved 128 finishing Tibetan pigs, divided into four feed treatment groups, with varying levels (0%, 5%, 10% and 15%) of FNOP replacing dry matter in the basal diet. The results indicated that substituting 5% to 15% FNOP had no adverse effects on pig growth performance. However, at a 15% substitution rate, there was a decrease in serum growth hormone and IGF-1 levels, along with an increase in feed-to-gain ratio. A 10% FNOP replacement notably increased the eye muscle area of pigs. Additionally, 5% and 10% FNOP substitutions reduced the drip loss of pork. The study also found that substituting 5% to 15% FNOP increased unsaturated fatty acids and umami nucleotide contents in pork, as well as raised serum total protein and uric acid (nucleotide metabolism related-product) levels. These findings suggest that moderate FNOP substitution might enhance meat quality and maintain growth and productive performance in Tibetan pigs by improving protein synthesis and nucleotide metabolism, while also reducing feed costs. The optimal substitution ratio identified was 10%.

Obsessive–compulsive disorder (OCD) is believed to follow a waxing and waning course, often according to environmental stressors. During the COVID-19 pandemic, pre-existing OCD symptoms were reported to increase and to change from checking to washing behaviors, while new-onset symptoms were predominantly of the hoarding type. In the present study, we followed the evolution of OCD symptoms, anxiety, depression, and insight of illness in forty-six OCD patients throughout the pandemic. Clinical measures were collected at four different time points before and during the COVID-19 pandemic in Italy. Within-subject comparisons were used to compare clinical scale scores across time, and correlations were examined between patients' baseline characteristics and changes in clinical scores. We found that all clinical measures increased during the first Italian lockdown, with respect to the pre-pandemic values. Anxiety decreased during the temporary elimination of restriction provisions, whereas severity of OCD symptoms and insight returned to pre-pandemic values during the second mandatory lockdown. These results were observed only in two sub-groups of patients: those taking benzodiazepines and those with shorter illness duration. Our findings suggest the need of additional clinical attention to these specific sub-groups of OCD patients in case of particularly distressing circumstances, while pointing to a possible adaptive role of their OCD symptoms when the environment requires a higher care of hygiene and extraordinary supply of essential resources.

Synchronous electrical cardioversion is a relatively common procedure in the emergency department (ED), often performed for unstable supraventricular tachycardia (SVT) or unstable ventricular tachycardia (VT). However, it is also used for stable cases resistant to drug therapy, which carry a risk of deterioration. In addition to the inherent risks linked with procedural sedation, there is a possibility of malignant arrhythmias or bradycardia, which could potentially result in cardiac arrest following this procedure. Here, we present a case of complete heart block unresponsive to transcutaneous pacing and positive inotropic and chronotropic drugs for 90 minutes, resulting in multiple cardiac arrests. The repositioning of the transcutaneous cardio-stimulation electrodes, one of them placed in the left latero-sternal position and the other at the level of the apex, led to immediate stabilization of the patient. Extubation of the patient was performed the following day, while full recovery and discharge within 7 days, after insertion of a permanent pacemaker.

Background and Objectives: Fibrillinopathies have different phenotypic expression: Marfan- like skeleton features, MLSF; mitral valve prolapse syndrome, MVPS; MASS phenotype, M= mitral valve prolapse, MVP, A= aortic root dilation, S= skeletal features, and the second S= (cutaneous) striae; Marfan syndrome, MS. These are inherited connective tissue diseases, provoked by a mutation of the encoding gene for a protein(fibrillin 1, FBN1) which has major importance in the formation of elastic fibers.The study had the following main objectives: the correlation between disc displacement, DD( a major sign for temporomandibular joint dysfunction, TMD) on magnetic resonance imaging, MRI, and aortic Z score(a major sign for aortic root dilation) on echocardiography; the predictive value of DD towards aortic Z score. DD had 2 types of severity: DD with reduction(the mild type, DDwR) , and DD without reduction( the severe type, DDwoR). Materials and Methods: The type of fibrillinopathy was precised by clinical exam( systemic score), ophthalmic exam(for ectopia lentis), and echocardiography(aortic Z score, MVP). Medical treatment consisted in betablockers, BB(for patients with tachycardia), or angiotensin II receptor blockers, ARB. Surgical treatment was addressed to aortic root aneurysm, and severe MR. DD benefited by dental conservatory treatment, or surgical restoration.Results: DD- Z score had a powerful correlation in MASS(Rho= 0.787, p&lt; 0.01), and in MS patients(Rho=0.819, p&lt; 0.01). For the entire sample, both DDwR- Z score, and DDwoR- Z score had a moderate correlation(Rho= 0.469, and respectively 0.669). Muchmore, DD was an important predictor for Z score. DDwoR had a double power of prediction for Z score, comparative with DDwR(B coefficient= 1.661 for DDwR, and 3.281 for DDwoR). Conclusions: TMD had a powerful correlation with aortic root dilation, in MASS, and MS patients from the sample. Likewise, TMD was a major predictor for aortic root dilation, in the entire sample. We can utilize in clinical practice, an extracardiac finding, TMD, obtained by a non-invasive technique, MRI, for cardiac severity stratification of fibrillinopathies.

This work presents the results of optimizing the physicochemical properties of composite briquettes based on microsilica for metallurgical-grade silicon production. Microsilica, a waste product of silicon production, contains a sufficiently high amount of silicon dioxide (96-97%). This fact makes microsilica a promising composite material for metallurgical processing. However, its granulometric composition limits its direct use. The method of briquetting on an industrial briquetting press was used. The influence of the granulometric composition of the composite mixture on the heat tolerance and strength of the finished briquettes was studied. The methods of obtaining and testing the briquettes, their composition, and the briquetting and drying process are described. The obtained briquettes were tested for the smelting of metallurgical silicon. The silicon recovery rate in the metal with the standard charge was 71%, while the recovery rate with the briquetted monocharge was 85%. The results of silicon smelting from the briquettes demonstrated the high quality of the obtained metal, corresponding to the standards of metallurgical-grade silicon. The implementation of these technologies not only improves the quality of the final product but also addresses environmental issues related to the disposal of microsilica, reducing its accumulation and minimizing its impact on the environment.

Background: This study attempted to construct musculoskeletal JEM using KWCS data and use it to evaluate the burden of these disorders in Korean workers. Methods: This study was conducted using data from the second to the sixth KWCS, and a total of 210,500 people were included. The jobs of the subjects were reclassified based on the unit groups of the 7th Korean Standard Classification of Occupation (KSCO). The intensity of exposure to work-related risk factors for musculoskeletal disorders was classified into ‘high’, ‘moderate’, and ‘low’ for the body segments involving the ‘upper extremities and neck’, ‘lower back’, and ‘lower extremities’. Results: The time of exposure was longest in the standing posture and repetitive hand and arm movements. An analysis of the intensity of exposure by body segments revealed that the highest intensity of exposure was to the upper extremities. For the upper extremities and neck, and the lower back, there was a exposure-response relationship in the association between intensity of exposure and musculoskeletal symptoms. However, for the lower extremities, there was a exposure-response relationship only at high exposure. Conclusion: In this study, a JEM for work-related risk factors for musculoskeletal disorders was constructed for the first time in Korea. The intensity of exposure to musculoskeletal risk factors was estimated for each occupation. The JEM constructed in this study is expected to have high applicability for assessing the risk of musculoskeletal disorders for each job with respect to the upper extremities and neck, and lower back.

As the number of publications is quickly growing in any area of science, the need to efficiently find relevant information amidst a large number of similarly themed articles becomes very important. Semantic searching through text documents has the potential to overcome the limits of keyword-based searches, especially since the introduction of attention-based transformers, which can capture contextual nuances of meaning in single words, sentences or whole documents. The deployment of these computational tools has been made simpler and accessible to investigators in every field of research thanks to a growing number of dedicated libraries, but a knowledge of how meaning representation strategies work is crucial to make the most out of these instruments. The present work aims at introducing the technical evolution of the meaning representation systems, from vectors to embeddings and transformers tailored to life science investigators with no previous knowledge of natural language processing.

Deep Eutectic Solvents (DESs) show promising abilities for the delamination of multilayer packaging films that are used in food packaging and in pharmaceutical blister packs. Due to the complexity of their structure, the recycling of these materials is a challenging task, leading to the easiest or cheapest option, landfilling. Towards the development of ‘green’ solvents for the efficient waste management and recycling, the conducted research focuses on the preparation of a range of hydrophobic and hydrophilic DES based on carboxylic acids. Also, their chemical and physical characterization, such as DSC, rheometer and density measurements, was followed for the determination of their properties. The laminate packaging waste products that were tested were Al/PE, PE/Al/PET, Al/PE/paper and PVC/PE/Al. Different batches of solvent systems were tested based on various naturally derived aliphatic and aromatic organic compounds as well as amino acids. The separated films were collected and studied further for the examination of the delamination extend. Results showed full or partial delamination of some materials as well as challenges of solvent systems. Variables such as temperature, agitation rate, mixing time and solvents ratios were monitored and collected during the design of experimental process. The results showed that the used DESs can offer an efficient, low-energy, affordable and green option for the delamination tested packaging materials.

Fagao is one of China's traditional gluten free staple foods made by rice or corn flour. Corn Fagao prepared by co-fermentation with sourdough and yeast exhibits better quality and less staling compared to traditional yeast-fermented Fagao. The physicochemical properties of corn Fagao batter during the sourdough-yeast co-fermentation were investigated. The results showed that compared with yeast fermentation, the gas production and viscosity of the batter increased by co-fermentation. The co-fermented batter shows higher hydrolysis of starch and less amylose content. The integrity of starch granules in co-fermented batter was damaged more seriously, the crystallinity and short-range ordered structure were less than yeast fermented batter, even though the crystal structure type of starch did not change obviously. The peak viscosity, minimum viscosity, final viscosity, decay value and recovery value of corn batter are reduced by co-fermentation, which can improve the thermal stability of the batter and slow down the aging. Co-fermentation also results in a more pronounced reduction in protein subunit contents than yeast fermentation. The changes in the physicochemical properties of corn Fagao batter help explain the quality improvement of corn Fagao made from co-fermentation method, and may provide theoretical references for co-fermentation with sourdough and yeast to other gluten free foods.

Carbon nanotubes (CNTs) can be considered as semi-rigid all-carbon polymers. However, unlike conventional polymers that can form 3D networks such as hydrogels or elastomers through crosslinking with each other in solution, the cylindrical carbon lattice of CNTs was not believed to be directly crosslinkable in solution until our recent discovery of UV-defluorination driven direct CNT crosslinking. In this study, we further reveal that the UV-defluorination-driven crosslinked CNTs are metastable and can decompose more readily than fluorinated or pristine CNTs upon exposure to Raman laser irradiation. Specifically, we investigate the stability of UV-defluorinated single-walled and multi-walled fluoro-nanotubes using Raman spectroscopy under controlled varying laser power. The results indicate that both the defluorinated single-walled and multi-walled CNTs are thermally less stable than pristine CNTs or untreated fluorinated CNTs, which can be attributed to the strains on the crosslinking bonds created from the curved carbon lattice of linked CNTs. This instability, particularly evident under high-power laser irradiation, leads to combustion processes ignited at relatively lower temperatures that cause an extended burned area centered on the laser spot, offering potential future applications as mechanically robust, lightweight materials with feasible post-use degradation options.

Electric vehicles (EVs) are pivotal in addressing the escalating environmental crisis. While EV drivetrains excel compared to those of vehicles with internal combustion engines (ICE), their energy storage systems are hampered by limited range, lifespan, and lengthy charging times. Hybrid energy storage systems (HESS) present a viable current solution to these issues. This review thoroughly explores state-of-the-art in the emerging field of multisource EVs that utilize HESS, incorporating any combination of batteries (BTs), supercapacitors (SCs), flywheels (FWs), fuel cells (FCs), and/or transmotors. In addition, the paper systematically categorizes and evaluates different hybrid configurations, detailing potential topologies and their respective advantages and limitations. Moreover, the paper examines diverse control algorithms used to manage these complex systems, focusing on their effectiveness and operational efficiency. By identifying current research gaps and technological challenges, this study aims to delineate future research directions that could enhance the deployment and optimization of multisource EVs, thereby addressing critical challenges such as energy density, system reliability, and cost-effectiveness.

We propose an innovative approach called SMPTC3, designed specifically to enhance security and privacy in cross-chain transaction verification. This approach addresses multi-chain, multi-participant information exchange and large-scale cross-chain transfers, resisting various types of malicious attacks. We leverage the verifiability of cross-chain transactions based on smart contracts and innovatively transform transaction information into confidential sets, organizing them into quadratic secret polynomials. By utilizing secret sharing and random distribution techniques, we construct a secure multiparty computation method, tailored for cross-chain transactions. To enhance the efficiency of cross-chain transactions, we introduce cross-chain batch processing technology, grouping inter-chain transactions into cross-chain transaction sets. Unlike traditional distributed notary technologies, SMPTC3 designates honest participants as a cross-chain notary group, reducing the time required for redundant signature confirmations and significantly lowering the possibility of malicious notaries. Theoretical analysis and empirical experiments demonstrate that SMPTC3 is highly efficient in addressing cross-chain transaction security issues.

Atmospheric pressure Microplasma is a simple, cost-effective, efficient, and eco-friendly procedure, which is superior to the traditional nanomaterials synthesis techniques. It generates high yields and allows for a controlled growth rate and morphology of nanomaterials. The silver (Ag) nanomaterials, with their unique physical and chemical properties, exhibit outstanding antibacterial and anti-fungal properties. Similarly, zinc oxide (ZnO) nanomaterials, known for their low toxicity and relatively lower cost, find wide applications in wound repair, bone healing, and antibacterial and anticancer applications. The use of core-shell nanomaterials in certain situations where some nanoparticles can cause serious harm to host tissues or organs is a testament to their potential. A benign material is coated over the core to reduce toxicity in these cases. This review compares the numerous configurations of microplasma systems used for synthesizing nanomaterials and their use in producing Ag, ZnO, and their core-shell (Ag-ZnO) nanomaterials for biomedical applications. The summary also includes the effect of control parameters, including cathode diameter, gas flow rate, precursor concentration, voltage, and current, on the nanomaterial's characteristics and applications. In addition, it provides a research gap in the synthesis of Ag, ZnO, and core shall nanomaterials by this technique, as well as the development and limitations of this technique and the use of these nanoparticles for biomedical applications.

High temperature Ni-superalloys are limited by reliance on critical elements and complex processing steps. High entropy alloys (HEAs) have demonstrated stable single/dual phase microstructures with strong ordering tendencies. A dual phase (FCC+BCC) Al0.5Co0.5CrFeNi1.5Ti0.25 alloy (developed using CALPHAD) was tested for room and high temperature compression behavior. The microstructure mainly comprises of coarse ordered FCC(L12) surrounding decomposed lamellae of ordered FCC(L12) and BCC(L21) phases, which coarsened upon annealing at high temperature (1100 °C) into a bi-continuous structure of disordered FCC+BCC(B2). Additionally, cold rollability of the cast alloy increased from &lt;5% to ~40% after annealing, with a corresponding softening observed in room temperature compression mainly due to disordering of FCC and BCC phases. Peak flow stresses of 793.45MPa, 535.12MPa, and 324.40MPa were achieved at 800oC, 900oC, and 1000oC respectively for the high temperature annealed alloy.