Abstract: The corrosion inhibition effects of Drimia maritima (L.) Stearn sin. Urginea matima (L.) Backer on three different materials, i.e. as-cast Al-7 wt.% Si alloy, SAE 1020 low carbon steel and commercially pure Al samples, into a stagnant and naturally aerated 0.5 M NaCl solution are evaluated. For this purpose, both the potentiodynamic polarization curves and electrochemical impedance spectroscopy with equivalent circuit are utilized. It is found that inhibition effect in-creases up to certain minor Drimia maritima content. Adsorption isotherms (e.g. Langmuir and Temkin) have indicated that all three examined material comprise physical adsorption mecha-nism. Al-Si alloys have attained inhibition efficiency of about 96% at 25 oC with 1250 ppm of Drimia maritima, and ~43% with 625 ppm at 45 oC. On the other hand, the cp. Al and SAE 1020 samples attain ~ 89% and 68% with 1250 ppm and 500 ppm at 25 oC, respectively. This clearly in-dicates that the dosage of Drimia maritima green inhibitor into NaCl solution posses certain sus-ceptibility for each distinctive material examined. Impedance parameters obtained by using CNLS (complex non-linear least squares simulations) are correlated and discussed.

The behavior of low concentrations of methanol (0.5 and 1.0 wt%) as a promoter for hydrate formation in seawater or pure water metastable solutions of methane was investigated using the classical molecular dynamics method at moderate temperature and pressure. The influence of methanol on the dynamics of the re-arrangement of the hydrogen bond network in seawater and pure water solutions of methane was studied by calculating the order parameters of the tetrahedral environment and intermolecular torsion angles for water molecules, as well as by calculating the number of hydrogen bonds, hydrate and hydrate-like cavities. It was found that hydrate nucleation can be considered a collective process in which the rate of hydrate growth is faster in systems with low concentrations of methanol and confident hydrate growth begins earlier in a metastable solution without sea salt with a small amount of methanol than in systems without methanol.

This study investigates the fabrication and optimization of Co-Fe-P catalysts on Cu foam using electroless deposition, focusing on their hydrogen generation efficiency. Deposition times were varied from 1 to 10 minutes, resulting in spherical Co-Fe-P particles growing from sub-micron to several microns in size. The optimal hydrogen generation rate of 27.66 ml/min was achieved with a 5-minute deposition. Extending the deposition to 10 minutes led to particle aggregation, reducing the efficiency per unit weight. The impact of bath temperatures from 30°C to 60°C was also assessed, with temperatures of 50°C and above promoting the development of larger 3D structures and increasing Fe and P contents (~9.3 wt.% and 10 wt.%). This enhanced hydrogen generation, peaking again at 27.66 ml/min. NaOH concentrations were varied from 0.5 M to 0.9 M, showing that concentrations over 0.8 M improved catalyst morphology and performance, increasing hydrogen generation to 10.03 ml/min. Among substrates tested, Co-Fe-P on Cu foam demonstrated the highest hydrogen generation rate due to better catalyst distribution and surface area. The study underscores the importance of deposition conditions and substrate choice in optimizing Co-Fe-P catalysts for hydrogen generation.

Calcium phosphates and manganese phosphates play a significant role in biomedical and engineering applications, and these compounds are both synergistic. These compounds could have great potential for use in different applications, particularly as precursors of biomaterials. Therefore, the aim of this study was to explore the effect of the gradual replacement of Ca2+ with Mn2+ on the phase composition and crystal structure of brushite (CaHPO4·2H2O), which could be useful for the production of Mono- and Biphasic Ca1−xMnxHPO4·nH2O Compounds. In order to prepare the starting solutions required for this study, Ca(NO3)2·4H2O, (NH4)2·HPO4, and Mn(NO3)2·4H2O were used at various molar concentrations. Afterwards, the Ca1−xMnxHPO4·nH2O compounds were prepared using dissolution and precipitation methods. These compounds were characterized using XRD, SEM, FT-IR, XPS, and TGA techniques. The findings revealed that Mn substituted Ca partially at low Mn/Ca molar ratios, 0.25, and Mn doping increased the unit cell of CaHPO4·2H2O. The produced biphasic compound was composed of monoclinic CaHPO4·2H2O and nanostructured orthorhombic MnHPO4·(H2O)3 after a continuous increase in the Mn/Ca molar ratio to 1.5. When the Ca/Mn molar ratio was above 1.5, a monophasic compound of the MnHPO4·(H2O)3 phase was formed. The MnHPO4·(H2O)3 compound was successfully prepared for the first time using this dissolution-precipitation method. It was also established that the Mn/Ca ratio of the starting solution can be modified to produce CaHPO4·2H2O and MnHPO4·(H2O)3 phases with specific weight percent compositions.

Alkaline and alkaline-thermal activation were used in an attempt to synthesize zeolites using the sedimented illite fraction of raw Devonian clays from the Kuprava clay pit in Latvia. The Si/Al molar ratio of these clays is 2.79. Thermal and hydrothermal treatments were conducted using 6M and 10M NaOH solutions, along with different curing environments. The treated samples were analyzed using XRD, FTIR, and SEM, and were compared to the raw and calcined illite fraction samples. The main phase that forms after alkaline treatment is hydrosodalite (Na8[AlSiO₄]₆(OH)₂∙2H₂O). Using a higher concentration of NaOH leads to a significant increase in hydrosodalite formation. Increasing the curing temperature from 120°C to 600°C slightly reduces hydrosodalite formation due to the crystallization of the nepheline (Na₃K(Al₄Si₄O₁₆)) phase. This phase forms relatively intensively when the chemically treated samples are cured in a nitrogen environment at 600°C, thereby reducing the formation of hydrosodalite. The characteristic layered-fused structure of clay minerals remains in all chemically treated samples when cured at 600°C in air, but it does not remain when cured at the same temperature in nitrogen. The intensive formation of hydrosodalite is mainly achieved through hydrothermal treatment, along with a primary treatment using 10M NaOH. Considering the calculated size of the crystallites, treatment with 6M NaOH and curing at 120°C can also be seen as beneficial for hydrosodalite formation.

Current paper is aiming to show the obtained results in manufacturing and characterization of graphite-based and metal composite materials suitable to be used in high voltage applications of automotive and/or aviation field. Thus, 4 types of materials have been processed and tested in order to assess their suitability to be used as current collector material for electric engines. The novelty of this work is the presentation of the new innovative technological process for obtaining the carbon/metal composite material used in the manufacture of sliding contacts for current collector heads, as well as the characteristics obtained for this material. All 4 obtained materials have been characterized from structural, mechanical and functional point of view and the most suitable of them has been chosen to be further developed by the end beneficiary.

Corrugated boards are used for packaging because of their high strength-to-weight ratio, recyclability, and biodegradability. They have an orthotropic sandwich structure with unique characteristics for each direction owing to their flute shape. In this study, the bending behavior was qualitatively analyzed for various variables through an FE-based simulation, and the possibility of an alternative test method for the four-point bending test on a corrugated board was examined through a similarity analysis with the experimental results. The cross-machine direction (CD) bending stiffness through finite element analysis (FEA) simulation was closely related to the thickness of the corrugated board. In AB-flute-double-wall (AB/F-DW), the difference in CD bending stiffness based on the bending direction was approximately 17.2% in the FEA simulation and approximately 10.5% in the experiment. However, the differences in the bending behavior (bending force vs. deflection plot) and bending stiffness based on the phase shift between the two flutes constituting BB-flute-double-wall (BB/F-DW) were insignificant. Overall, the CD bending behavior of the corrugated board was simulated relatively well through FEA simulation. However, it was impossible to simulate the machine-direction (MD) bending behavior through FE-based simulation because of a decrease in convergence and a large error caused by the variability of the contact condition of the modeled test specimen with a non-uniform MD cross-section.

Wide-bandgap tin oxide (SnO₂) thin-films are frequently used as an electron-transporting layers in perovskite solar cells due to superior thermal and environmental stabilities. However, its crystallization by conventional thermal methods requires typical temperatures between 300 and 900 ◦C [1] with up-to 60 min crystallization times. These post-processing conditions severely limit the choice of substrates and reduce the large-scale manufacturing capabilities. This work describes the intense pulsed light-induced crystallization of SnO₂ thin films using only 500 μs of exposure time. Thin-film properties are investigated using both impedance spectroscopy and photoconductivity characteristic measurements. Nyquist plot analysis establishes that the process parameters have a significant impact on the electronic and ionic behaviors of the SnO2 films. Most importantly, we demonstrate that light-induced crystallization yields improved topography and excellent electrical properties through enhanced charge transfer, improved interfacial morphology and better ohmic contacts compared to thermally-annealed SnO₂ films.

In order to study the corrosion resistance of 904L composite plate pressure vessel under high temperature and high pressure gas field environment, the pitting corrosion and stress corrosion cracking resistance of 904L composite plate body and weld material were compared with those of 2205 composite plate and 825 composite plate, which have been used in high temperature and high pressure gas field environment. The results showed that the pitting resistance of 904L composite plate was lower than that of 825 composite plate and higher than that of 2205 solid solution pure material plate and 2205 composite plate. The corrosion resistance of welds on 904L composite plate with different materials was very different. The corrosion rate of 904L composite plate body, welding seam and surfacing welding were all slight corrosion, and the sensitivity of chloride stress corrosion cracking was low in the simulation of the corrosion environment of high temperature and high pressure gas field. 904L composite plate met the requirements of corrosion resistance of pressure vessel material in high temperature and high pressure gas field environment.

7046 aluminum alloy has good fatigue property, corrosion resistance and weld property, but the moderate strength and plasticity limit its wider application and development. In the present study, severe plastic deformation (SPD) was applied prior to T6 treatment to significantly strengthen and toughen the 7046 aluminum alloy. Results indicate that the alloy processed by 4 passes of equal channel angular pressing (ECAP) at 300 ℃ prior to T6 treatment exhibits an excellent mechanical performance, with ultimate tensile strength (UTS) and elongation (EL) of 485 MPa and 19%, exhibiting an improvement of 18.6% and 375% compared to that of the T6 alloy, respectively. The mechanical properties of the alloy are further improved by the additional room temperature (RT) rolling process, with UTS of 508 MPa and EL of 23.4%. There are more precipitates of η' and Al6Mn phases in the 300℃4P-R80%-T6 and 300°C4P-T6 alloys, which contribute to the strengthening and toughening enhancement by SPD processed T6 alloy. The results of this work may shed some light on enhancing 7046 aluminum alloy.

Powders with phase composition including syngenite K2Ca(SO4)2·H2O and/or calcium sulfate di-hydrate (gypsum) CaSO4·2H2O were synthesized from powder of calcium carbonate CaCO3 and water solutions of potassium hydrosulfate KHSO4 of various (0.5M, 1M and 2M) concentrations. Molar ratio of starting salt KHSO4/CaCO3=2 were used to provide formation of syngenite K2Ca(SO4)2·H2O. But when using 0.5M water solution of potassium hydrosulfate KHSO4 the phase composition of synthesized powder was presented by calcium sulfate dihydrate (gypsum) CaSO4·2H2O. When using 1M and 2M water solution of potassium hydrosulfate KHSO4 the syn-genite K2Ca(SO4)2·H2O was found as predominant phase in synthesized powders. According es-timations made from thermal analysis data when 1.0M and 2.0M water solutions of potassium hydrosulfate KHSO4 were used the content of calcium sulfate dihydrate (gypsum) CaSO4·2H2O in these powders were not higher then as 7.9 and 1.9 % respectively. Phase composition of products isolated from mother liquors via water evaporation consisted of syngenite K2Ca(SO4)2·H2O and potassium sulfate (arcanite) K2SO4. Synthesized powders can be used in preparation of biocom-patible bioresorbable materials with phase composition in the K2O‑CaO‑SO3‑H2O system; as matrix of thermo- or photo-luminescent materials; as components reducing the setting time and increasing strength of sulfate cements; in the fertilizing industry and also as a components of Martian regolith simulant.

In recent years, due to the detrimental impact of traditional gas-liquid refrigerants on the environment, the pursuit of solid-state refrigeration technology based on elastocaloric effect, as a promising sustainable alternative, has been promoted. However, the traditional trial-and-error method is inefficient and difficult to meet the material application requirements. In this work, machine learning (ML) was employed to accelerate the development of NiTi-based shape memory alloy (SMA) with excellent elastocaloric effect. By means of active learning, we identified 9 novel NiTi-based SMAs in four iterations, the phase transformation-induced entropy change (ΔS) of which are as high as over 90 J/kg·K-1. Moreover, the model exhibits good interpretability, allowing us to understand the relevance between the target and features from the aspect of mechanism.

In the presented work, on the example of thin-walled specimens made by selective laser melting technology from AlSi10Mg subjected to preliminary heat treatment, it is shown that there is a critical point of transition from the elastic-plastic region of the engineering stress-strain diagram to the yield and fracture stresses. It was found that the critical point has a strong statistically significant correlation (0.83 by Spearman and 0.93 by Pearson) with the strain hardening coeffi-cient calculated in the section from yield strength to fracture strength. A regression equation linking the critical transition point to the strain hardening coefficient was obtained. It is shown that with increasing plasticity of thin-walled samples obtained by selective laser melting of AlSi10Mg leads to a change in the type of stress distribution in the elastic-plastic region (the Weibull distribution changes to a normal distribution) and the contribution of the probability density of stress distribution described by the Cauchy distribution with a mode near the fracture stress to the full probability density of fracture increases.

Diabetes is a major health concern that the next-generation of on-demand insulin releasing implants may overcome for personalized therapy. Therein, 3D-printed phenylboronic acid-containing subcutaneous implants with on-demand glucose-triggered drug release abilities are produced using high resolution stereolithography technology. To that end, the methacrylation of phenylboronic acid is targeted following a two-step reaction. The resulting photocurable phenylboronic acid derivative is accordingly incorporated within bioinert polyhydroxyethyl methacrylate-based hydrogels at varying loadings. The end result are sub-centimeter scaled 3D-printed bionert implants that can be remotely activated with 1,2-diols and 1,3-diols such as glucose for on-demand drug administration such as insulin. As a proof of concept, varying glucose concentration from hypoglycemia to hyperglycemia levels readily allow the release of pinacol, i.e. a model molecule with similar release properties than insulin, at respectively low and high rates. In addition, the results demonstrated that adjusting the geometry and size of the 3D-printed part is a simple and suitable method for tailoring the release behavior and dosage.

The utilization of black mulberry fruit as a precursor for C-dot synthesis represents a novel ap-proach to biosynthesizing C-dots. Through the implementation of a hydrothermal autoclave, we successfully produced C-dots using the fruit extract. This environmentally conscious and sustain-able method of synthesis presents a promising avenue for C-dot production. Our findings demon-strate the remarkable photocatalytic activity of the C-dots, as evidenced by their effective degra-dation of pollutants under visible light irradiation. This discovery holds significant implications for addressing water contamination issues and promoting environmental remediation efforts. Fur-thermore, we conducted a thorough investigation to determine the optimal doping concentration of C-dots, ultimately identifying 0.2 M as the ideal concentration. At this specific concentration, the photo catalytic degradation of pollutants reached an impressive rate of 95.8%. The enhanced photocatalytic activity can be attributed to the increased electron trapping resulting from the presence of additional surface sites and the absorption of different wavelengths of light. In sum-mary, this research contributes to the sustainable synthesis of carbon dots using black mulberry fruits as a precursor, while also providing a comprehensive analysis of their optical and photo-catalytic properties.

The Internet of Things (IoT) technology connects the real world and the network world by integrating sensors and internet technology, which has greatly changed people's lifestyles, showing its broad application prospects. However, traditional materials for the sensors and power components used in IoT limit its development to high-precision detection, long-term endurance, and multi-scenario applications. Metal halide perovskite, with the unique advantages such as excellent photoelectric properties, adjustable bandgap, flexibility, and mild process, exhibiting enormous potential to meet the requirements for IoT development. This paper provides a comprehensive review of metal halide perovskites' application in sensors and energy supply modules within IoT systems. Advances on perovskite-based sensors were discussed as to gas, humidity, photoelectric, and optical sensors. The application of indoor photovoltaics based on perovskite in IoT systems were also discussed. At last, the application prospects and challenges of perovskite-based devices in IoT are summarized.

The bulk LiNa5Mo9O30 (LNM) crystals were successfully grown in the [010] and [001] directions without internal inclusions and cracks by the Czochralskii method with low temperature gradient. The crystal grown in the [010] direction showed a tendency to twinning. The crystal grown in the [001] direction demonstrated high structural perfection (FWHM=13'') for the (001) plane and high optical quality Δn≈210-5. The laser induced damage threshold was measured along a, b and c axes and was 15.7, 27.0 and 27.5 J/cm2 respectively. The thermo-optical coefficient dn/dT was measured for the main crystallographic axes, which was -5.7510-6, -2.0210-5 and 3.6510-6 K-1 along the a, b and c axes, respectively. The second harmonic generation (SHG) is conducted in crystalline LNM sample. The maximum efficiency value of 3.5% at pump power of 12 W had been achieved.

Photocatalytic ammonia decomposition to produce N2 and H2 was achieved using single-walled carbon nanotube (SWCNT) nanohybrids. Physical modification of ferrocene-dye-encapsulated CNTs by amphiphilic C60-dendron yielded nanohybrids with a dye/CNT/C60 coaxial heterojunction. Upon visible light irradiation, an aqueous solution of NH3 and dye@CNT/C60-dendron nanohybrids produced both N2 and H2 in a stoichiometric ratio of 1:3. Action spectra of this reaction clearly demonstrated that the encapsulated dye acted as the photosensitizer, with an apparent quantum yield (AQY) of 0.22% at 510 nm (the λmax of the dye). This study presents the first example of dye-sensitized ammonia decomposition and offers a new avenue for developing efficient and sustainable photocatalytic hydrogen production systems.

This study primarily investigates the effect of fly ash (FA) content on the mechanical properties and hydration performance of alkali-activated ground granulated blast furnace slag cements (AAGC), and compares the related properties with ordinary Portland cement (OPC). Additionally, the study examined the hydration products, thermal analysis, MIP, SEM, chemically bound water, and pH values of AAGC. The compressive strength of AAGC showed a retrogression phenomenon from 3 to 28 days, with the 14-day and 28-day compressive strengths of AAGC being higher than those of OPC. The AAGC with 20% FA content exhibits the highest 28-day compressive strength (75 MPa). The hydration heat release rate curved of OPC and AAGC can be divided into the initial induction period, induction period, acceleration period, deceleration period and steady period. As FA content increases, the 28-day pore volume of AAGC increased while pH values and chemically bound water decrease. SEM images of AAGC with low FA content showed more microcracks.

The combination of micro- or nanofluidics and strong light–matter coupling has gained much interest in the past decade, which has led to the development of advanced systems and devices with numerous potential applications in different fields, such as chemistry, biosensing, and material science. Strong light–matter coupling is achieved by placing a dipole (e.g. an atom or a molecule) into a confined electromagnetic field, with molecular transitions being in resonance with the field and the coupling strength exceeding the average dissipation rate. Despite intense research and encouraging results in this field, some challenges still need to be overcome, related to the fabrication of nano- and microscale optical cavities, stability, scaling up and production, sensitivity, signal-to-noise ratio, and real-time control and monitoring. The goal of this paper is to summarize recent developments of micro- and nanofluidic systems employing strong light–matter coupling. An overview of various methods and techniques used to achieve strong light–matter coupling in micro- or nanofluidic systems is presented, preceded by a brief outline of the fundamentals of strong light–matter coupling and optofluidics operating in the strong coupling regime. The potential applications of these integrated systems in sensing, optofluidics, and quantum technologies are explored. The challenges and prospects in this rapidly developing field are discussed.

In machining, there is a constant effort to achieve the expected roughness of the machined surface while maintaining the life of the cutting tool during its operation. The methods used for extending machinability characteristics can be applied due to cooling and lubrication. One of the latest, but not new, targeted cooling techniques have become cryogenic treatment, which uses substances that exhibit extremely low-temperature values of about 123 K. This is a very environmentally friendly technique compared to the current standardized cooling and lubricating fluids. The main task of such cooling is to change the properties of the workpiece so that it exhibits the properties of a brittle material. Bringing the workpiece structure in this way can result in easier material separation through the chip. In the article, the obtained test results can approximate the behavior of various materials during cryogenic cooling.

Previous reviews by the authors [1, 2] indicate the continuing development and improvement of thermal protective systems through the introduction of polymer nanocomposites into polymer matrix composites. These materials perform as thermal protective systems for a variety of aerospace applications, such as thermal protection systems (TPS), solid rocket motors (SRM) nozzles, internal insulation of SRM, leading edges of hypersonic vehicles, and missile launch structures. A summary of the most recent, global technical research is presented. Polymeric resin systems continue to emphasize phenolic resins and other materials. New high-temperature organic resins based on phthalonitrile (PN), and polysiloxane are described and extend the increased temperature range of resin matrix systems.

In recent years, the demand for natural and synthetic zeolites has surged due to their distinctive properties and myriad industrial applications. This research aims to synthesise crystalline zeolites by co-recycling two industrial wastes: salt slag (SS) and rice husk ash (RHA). Salt slag, a problem-atic by-product of secondary aluminium smelting, is classified as hazardous waste due to its reac-tive and leachable nature, though it is rich in aluminium. Conversely, RHA, an abundant and cost-effective by-product of the agro-food sector, boasts a high silicon content. These wastes were utilised as aluminium and silicon sources for synthesising various zeolites. The study examined the effects of temperature, ageing time, and sodium concentration on the formation of different zeolite phases and their crystallinity. Results indicated that increased Na+ concentration favoured SOD zeolite formation, whereas LTA-type zeolite formation was promoted at higher temperatures and extended ageing times. The formation range of the different zeolites was defined and supported by a crystallographic, microstructural, and morphological analysis. Additionally, the thermal be-haviour of the zeolites was investigated. This work underscores the potential to transform indus-trial waste, including hazardous materials like salt slag, into sustainable, high-value materials, fostering efficient waste co-recycling and promoting clean, sustainable industrial production through cross-sectoral industrial symbiosis.

Textile wastewater containing dyes pose significant environmental hazards. Advanced oxidative processes, especially the heterogeneous photo-Fenton process, are effective in degrading a wide range of contaminants due to high conversion rates and ease of catalyst recovery. This study evaluates the photocatalytic degradation of azo dyes Acid Red 18 (AR18), Acid Red 66 (AR66) and Orange 2 (OR2) using magnetite as a catalyst. The magnetic catalyst was synthesized via a hydrothermal process at 150°C. Experiments were conducted at room temperature, investigating the effect of catalyst dosage, pH, and initial concentrations of H2O2 and AR18 dye. Kinetic and thermodynamic studies were performed at 25, 40 and 60°C for the three azo dyes (AR18, AR66 and OR2) and the effect of the dye structures on the photocatalytic efficiency was investigated. At 25 °C for 0.33 mmol.L-1 of dyes at pH 3.0, using 1.4 g.L-1 of catalyst and 60 mg.L-1 of H2O2 under a UV radiation of 16.7 mW.cm-2 the catalyst showed a 62,3% degradation for AR18, 79.6% for AR66, and 83.8% for OR2 in 180 minutes of reaction. The oxidation of azo dyes under these conditions is spontaneous and endothermic. The pseudo-first order kinetic constants indicated a strong temperature dependence with an order of reactivity of the type: OR2 > AR66 > AR18, which is associated to the characteristics of molecular complexity (size, steric hindrance, aromatic conjugation), electrostatic repulsion and the nature of the acid-base interactions on the catalytic surface.

As high strength and ultra-high strength steels are widely used in all kinds of modern welded constructions, a lot of research is carried out to investigate the mechanical properties of weldments of these steels but there is a scarce information on such important characteristic as their corrosion behaviour. This research focuses on the corrosion behaviour of weld metal of weldments of S906QL and S700MC steels. Weld metal was tested electrochemically in a 3,5% NaCl aqueous solution via potentiodynamic scan to determine corrosion rate and its dependence on welding gap. No influence of welding gap on corrosion rate was found but the experimental results suggested that corrosion rate depended on the chemical composition of filler material and the microstructure of weld metal.

This study investigates the use of geopolymer technology as an alternative for the management of mine tailings, which is a serious environmental problem in mining environments including that of Arequipa region of Peru. In this study, the mixture of stabilized mine tailings with different percentages of binders (metakaolin and pumice) and their impact on the mechanical, microstructural, and toxicological properties of the synthesized geopolymers were analyzed. The ratios of mine tailings to binder material varied between 100/0 and 0/100. The activation was carried out with an alkaline solution of sodium hydroxide (10M) and sodium silicate (modulus 2.5). 50 mm cubic specimens were fabricated, and 7 mixtures with 3 replicates each were evaluated. The evaluations included compressive strength at 7, 14, 28, and 56 days of curing, chemical analysis by X-Ray Diffraction (XRD) and Fourier Transform Infrared Spectroscopy (FT-IR), microstructural characterization by Scanning Electron Microscopy (SEM/EDS), thermal behavior by thermogravimetry and differential thermal analysis (TGA/DTA) between 40°C and 1000°C, and toxicological tests by the Toxicity Characteristic Leaching Procedure (TCLP, EPA 1311) to determine the efficiency of immobilization of toxic metals. The results showed good mechanical strength, reaching 25 MPa at 7 days of curing, high microstructural stability with an average pore size of 7.21 μm, and good efficiency in the immobilization of heavy metals in geopolymers composed of 60% - 40% and 70% - 30% of the mine tailings - binders ratio, as the concentrations of As, Cd, Pb, Hg were below the established thresholds, acquiring the classification of non-hazardous materials. Geopolymers with 30 to 50% binder showed good mechanical behavior, microstructural stability, and high efficiency in the immobilization of heavy metals, complying with current regulations. Therefore, these geopolymers are suitable for various applications and in different environmental conditions.

Carbon nanotubes (CNTs) can be considered as semi-rigid all-carbon polymers. However, unlike conventional polymers that can form 3D networks such as hydrogels or elastomers through crosslinking with each other in solution, the cylindrical carbon lattice of CNTs was not believed to be directly crosslinkable in solution until our recent discovery of UV-defluorination driven direct CNT crosslinking. In this study, we further reveal that the UV-defluorination-driven crosslinked CNTs are metastable and can decompose more readily than fluorinated or pristine CNTs upon exposure to Raman laser irradiation. Specifically, we investigate the stability of UV-defluorinated single-walled and multi-walled fluoro-nanotubes using Raman spectroscopy under controlled varying laser power. The results indicate that both the defluorinated single-walled and multi-walled CNTs are thermally less stable than pristine CNTs or untreated fluorinated CNTs, which can be attributed to the strains on the crosslinking bonds created from the curved carbon lattice of linked CNTs. This instability, particularly evident under high-power laser irradiation, leads to combustion processes ignited at relatively lower temperatures that cause an extended burned area centered on the laser spot, offering potential future applications as mechanically robust, lightweight materials with feasible post-use degradation options.

The article presents the results of research work devoted to improving the characteristics of paint and varnish coatings based on aqueous dispersions of polyacrylates, it is proposed to modify them by introducing mineral raw materials as fillers and hydrated lime with subsequent processing in a vortex layer apparatus. Introduction of activated diatomite does not cause deterioration of covering power, adhesion and increase of porosity of the paint material. Modification of coatings contributes to the increase of their operational properties, which can be associated with the reduction of free volume in the composite, formation of polymer boundary layers with modified physical and chemical properties. The aim of the study is to obtain water-dispersion paint and varnish composition containing modified diatomite on polyacrylate basis and subsequent study of the main physical and mechanical parameters. The work has been carried out by the following method: determination of porosity, adhesion, elasticity, covering power of the control composition; determination of porosity, adhesion, elasticity, and covering power of the obtained composites using modified filler; investigation of the influence of radiation in the infrared spectrum of the paint coating surface using FLIRB620 thermal imager. As a result of research works it was noticed that modification of water dispersions with silica activated diatomite helps to eliminate the main disadvantages of materials and coatings based on acrylate binder - low water resistance and low physical and mechanical characteristics, introduction of modified diatomite into water emulsion paint on acrylate base does not lead to deterioration of the main performance characteristics of paint coatings - porosity, adhesion, elasticity and covering.

There is an increasing need for compact low-cost NMR apparatus that can be used on the laboratory bench and in the field. There are four main usage variants of usage: a) Time-Domain apparatus, particularly for physical measurements; b) Frequency Domain apparatus, particularly for chemical analysis, c) NMR Cryoporometry apparatus for measuring pore-size distributions, and d) MRI apparatus for imaging. For all of these, variable temperature capability may be vital. We have developed compact low-cost apparatus targeted at these applications. We discuss a hand-held size NMR spectrometer, and three different holdable NMR magnets, with sufficiently large internal bores for the Lab-Tools compact Peltier thermo-electric cooled variable-temperature probes. Currently the NMR Spectrometer is very suitable for a), NMR time-domain relaxation and c), NMR Cryoporometry. With a suitable high-homogeneity magnet it is also appropriate for simple use b), spectral analysis, or, with a suitable gradient set, use d), MRI. Together, the NMR Spectrometer, one of the NMR variable-temperature probes, and any of these NMR magnets make an excellent NMR Cryoporometers, as demonstrated by this paper, and previously published research. Equally, they make versatile general-purpose variable-temperature NMR systems for materials-science.

In this work, non-ordered and ordered CeO2-based catalysts are proposed for the CO2 conversion to dimethyl carbonate (DMC). Particularly, a non-ordered mesoporous CeO2, consisting of small nanoparticles of about 8 nm, is compared with two highly porous (635-722 m2/g) ordered CeO2@SBA-15 nanocomposites obtained by two different impregnation strategies (a two-solvent impregnation (TS) and a self-combustion (SC) method), with a final CeO2 loading of 10 wt%. The Rietveld analyses on XRD data combined with TEM imaging evidence the influence of the impregnation strategy on the dispersion of the active phase: nanoparticles of 8 nm for the TS composite vs. 3 nm for the SC composite. The catalytic results show comparable activity for the mesoporous ceria and the CeO2@SBA-15_SC nanocomposite, while a lower DMC yield was found for the CeO2@SBA-15_TS nanocomposite. This finding is presumably ascribed to a partial obstruction of the pores by the CeO2 nanoparticles in the case of the TS composite, which leads to a reduced accessibility of the active phase. On the other hand, in the case of the SC composite, where the CeO2 particle size is much lower than the pore size, there is an improved accessibility of the active phase to the molecules of the reactants.

The rapid expansion of flexible and wearable electronics has necessitated a focus on ensuring their safety and operational reliability. Gel Polymer Electrolytes (GPEs) have become preferred alternatives to traditional liquid electrolytes, offering enhanced safety features and adaptability to the design requirements of flexible lithium-ion batteries. This review provides a comprehensive and critical overview of recent advancements in GPEs technology, highlighting significant improvements in their physicochemical properties, which contribute to superior long-term cycling stability and high-rate capacity compared to traditional organic liquid electrolytes. Special attention is given to the development of smart GPEs endowed with advanced functionalities such as self-protection, thermotolerance, and self-healing properties, which further enhance battery safety and reliability. The review also critically examines the application of GPEs in high-energy cathode materials, including Lithium Nickel Cobalt Manganese (NCM), Lithium Nickel Cobalt Aluminum (NCA), and thermally stable Lithium Iron Phosphate (LiFePO4). Despite the advancements, several challenges in GPE development remain unresolved, such as improving ionic conductivity at low temperatures and ensuring mechanical integrity and interfacial compatibility. The review concludes by outlining future research directions and the remaining technical hurdles, providing valuable insights to guide ongoing and future efforts in the field of GPEs for lithium-ion batteries, with a particular emphasis on applications in high-energy and thermally stable cathodes.

Wastewaters containing synthetic dyes, namely molecules with large aromatic structure which can produce harmful effects on the aquatic environment, are difficult to treat. Accordingly, and based on the adsorption technology, this work proposes the use of porous carbons as adsorbents of a red dye used in the wood industry. Three porous carbonaceous materials with relatively high porosity and tunable pore size were prepared by transformation of a nitrogen-rich precursor, polyacrylonitrile (PAN), at high temperature: N doped carbon (PAN-C), N-doped activated carbon with potassium hydroxide (PAN-C-Act) and N, S-co doped carbon with sulphur (PAN-S-C). Different experiments were planned to study the influence of pH (1.9-2.3, 6-6.8 and 11.8-12.6), solid/liquid ratio (S/L, 0.43-0.53 and 1.73-1.91 g L−1) and initial concentration (24 – 28 mg L−1 and 231 – 285 mg L−1) on the dye removal from aqueous solutions. The best results were found for the activated carbon (PAN-C-Act) at all concentrations and pH essayed. Specifically, the maximum adsorption capacity of 602.3 mg g−1 (99.9%, adsorption yield) was obtained at S/L of about 0.5 g L−1, acid pH, 285 mg L−1 and 48 h. Adsorption kinetics was better explained by the pseudo-second order model. Also, the existence of external mass transfer and intra-particle diffusion was confirmed.

A tetraphenylethylene-derived compound, TPEPhDAT, has been prepared by successive Suzuki-Miyaura coupling and ring-closing reactions. This compound exhibits aggregation-induced emission (AIE) properties in the DMSO/MeOH system, with a fluorescence emission intensity in the aggregated state that is 5-fold higher than that of its counterpart in a dilute solution. Moreover, the diaminotriazine structure of the molecule is a good acceptor of protons, and thus the TPEPhDAT molecule exhibits acid-responsive fluorescence. TPEPhDAT was protonated by trifluoroacetic acid (TFA), leading to a fluorescence quenching, which was reversibly restored by treatment with ammonia (On-Off switch). Time-dependent density functional theory (TDDFT) computational studies have shown that protonation enhances the electron-withdrawing capacity of the triazine nucleus and reduces the bandgap, producing a more intense intramolecular charge transfer (ICT), thus leading to fluorescence quenching. MeOH can easily remove the protonated TPEPhDAT, and this acid-induced discolouration and erasable property can be applied in anti-counterfeiting.

The dynamic landscape of 3D printing has experienced a notable surge in the development of diverse filaments tailored for a wide range of applications in medicine. This experimental study thoroughly examines the mechanical properties of nine popular 3D printer filaments, namely PLA, ABS, HIPS, PETG, PA, Carbon Fiber, Ceramic, PMMA, and Metal composite. Focusing on key aspects such as tensile strength and compressive tests, the study delves into the intricate mechanical characteristics of these 3D printer filaments. In addition to the mechanical properties, the study provides a comprehensive exploration of essential filament attributes, including melting point, bed temperature requirements, and density of nine different filament properties. Furthermore, the study addresses crucial considerations in material selection for different applications. Through insightful comparisons, the article illuminates the advantages and limitations of various available filaments within the realm of applications. This study serves as a valuable resource, offering nuanced insights for researchers, engineers, and medical professionals seeking a deeper understanding of the mechanical characteristics of 3D printer filaments and their potential applications.

Nanomaterials have shown significant promise for enhancing the performance of composite materials and increasing their functionality for various industrial applications. This review explores the unique properties of nanomaterials, particularly carbon-based nanomaterials, and provides key findings in utilizing them to enhance composite performance. It highlights specific nano-based composite materials and their significant potential in advancing the field of nanocomposites. Challenges associated with nanocomposite production and utilization are also discussed, along with possible solutions to address them. Finally, the study provides recommendations for continued research and innovation in nanocomposites to fully unlock the benefits of these advanced materials for broader future applications.

The dissolution of CO₂ in seawater in the form of bicarbonate ions is an attractive alternative to the storage in geological formations, on the conditions that the storage is stable over long times and does not harm the marine environment. In this work, we focus on the long-term chemical stability of CO₂ absorbed in seawater as bicarbonate, by monitoring the physico-chemical properties of the solutions (pH, dissolved inorganic carbon and alkalinity), in six different sets of experiments on both natural and artificial seawater lasting up to three months. The bicarbonate treatment of natural seawater consists in pouring pre-equilibrated solutions obtained from the reaction of CO₂ and Ca(OH)₂. If the pre-equilibrated mixture does not exceed a critical threshold (ca. 1000-1500 mmol/L), the resulting bicarbonate-rich solutions can be stable for over three months.

Zinc cobalt oxide-zinc hydroxide (ZnCo2O4-Zn(OH)2) microspheres were successfully fabricated on carbon cloth via a sample hydrothermal method. The surface morphology of these microspheres and their efficacy in degrading methyl violet were further modulated by varying the thermal annealing temperatures. The manipulation of thermal annealing temperatures was pivotal in adjusting the porosity of ZnCo2O4-Zn(OH)2 microspheres to amplify their photocatalytic performance. Various analytical techniques were utilized to evaluate the physical and chemical properties of the ZnCo2O4-Zn(OH)2 microspheres, including field-emission scanning electron microscopy, energy-dispersive spectroscopy, X-ray diffraction, field-emission transmission electron microscopy, X-ray photoelectron spectroscopy, and UV-vis spectroscopy. Compared to untreated ZnCo2O4-Zn(OH)2 microspheres, those subjected to thermal annealing exhibited increased specific surface area and light absorption capacity, rendering them highly effective photocatalysts under UVC light exposure. Subsequent studies have confirmed the superior performance of ZnCo2O4-Zn(OH)2 microspheres as a reusable photocatalyst for degrading methyl violet and tetracycline. Additionally, trapping experiments during the photodegradation process involving ZnCo2O4-Zn(OH)2 microspheres have identified hydroxyl radicals (·OH) and superoxide radicals (·O2–) as the primary reactive species.

Over the past decade, the production of biofuels from lignocellulosic biomass has steadily increased to offset the use of fuels from petroleum. To make biofuels cost-competitive, however, it is necessary to add value to the “ligno-” components (up to 30% by mass) of the biomass. The properties of lignin, in terms of molecular weight (MW), chemical functionality, and mineral impurities often vary from biomass source and biorefinery process, resulting in a challenging precursor for product development. Activated carbon (AC) is a feasible target for the lignin-rich byproduct streams because it can be made from nearly any biomass and it has a market capacity large enough to use much of the lignin generated from the biorefineries. However, it is not known how the variability in the lignin affects the key properties of AC, because until now, they could not be well controlled. In this work, various fractions of ultraclean (< 0.6 % ash) lignin are created with refined MW distributions using Aqueous Lignin Purification using Hot Agents (ALPHA) and used as precursors for AC. AC is synthesized via zinc chloride activation and characterized for pore structure and adsorption capacity. We show that AC surface area and the adsorption capacity increase when using lignin with increasing MW, and furthermore, that reducing the mineral content of lignin can significantly enhance the AC properties. The surface area of the AC from the highest MW lignin can reach ~1830 m2/g (absorption capacity). Furthermore, the single step activation carbonization using zinc chloride allows for minimal carbon burnoff (< 30%) capturing most of the lignin carbon compared to traditional burn off methods in biorefineries for heat generation.

An arc glow discharge device was used to prepare a helical carbon fiber skeleton with helical carbon fibers hooked to each other by spraying hydrogen and ethanol mixture onto the iron wire substrate through the discharge area, using anhydrous ethanol as carbon source. The various growth modes of carbon fiber during the formation of carbon fiber skeleton were investigated. A ring appearance that indicates a change in the direction of carbon fiber growth is observed. And double helical carbon fiber was constructed from single helical carbon fiber in two ways. A super-large carbon fiber with a diameter of about 13μm was observed, and it is speculated that this super-large carbon fiber is the backbone of the carbon fiber skeleton. The mechanical properties of carbon fiber skeleton are isotropic.

Temperature and pressure sensors currently encounter challenges such as slow response times, large sizes, and insufficient sensitivity. To address these issues, we developed tetraphenylethylene (TPE)-doped polyvinylidene fluoride (PVDF) nanofiber membranes using electrospinning, with process parameters optimized through a convolutional neural network (CNN). We systematically analyzed the effects of PVDF concentration, spinning voltage, tip-to-collector distance, and flow rate on fiber morphology and diameter. The CNN model achieved high predictive accuracy, resulting in uniform and smooth nanofibers under optimal conditions. Incorporating TPE enhanced the hydrophobicity and mechanical properties of the nanofibers. Additionally, the fluorescent properties of the TPE-doped nanofibers remained stable under UV exposure and exhibited significant linear responses to temperature and pressure variations. The nanofibers demonstrated a temperature sensitivity of -0.976 gray value/°C and pressure sensitivity with an increase in fluorescence intensity from 537 a.u. to 649 a.u. under 600 g pressure. These findings highlight the potential of TPE-doped PVDF nanofiber membranes for advanced temperature and pressure sensing applications.

Hydrogen sulfide is present in active or extinct volcanic areas (mofettas). The habitable premises in these areas are affected by the presence of hydrogen sulfide, which, even in low concentrations, gives off a bad to unbearable smell. If the living spaces considered are closed enclosures, then a system can be designed to reduce the concentration of hydrogen sulfide. This paper presents a membrane way to reduce the hydrogen sulfide concentration to acceptable limits using a cellulosic derivative-propylene hollow fiber based composite membrane module. The cellulosic derivatives considered were carboxymethyl–cellulose (NaCMC), cellulose acetate (CA), methyl 2–hydroxyethyl–cellulose (MHEC), and 2–hydroxyethyl–cellulose (HEC). In the permeation module, hydrogen sulfide is captured with a solution of cadmium that forms cadmium sulfide, usable as a luminescent substance. The composite membranes were characterized by SEM, EDAX, FTIR, FTIR 2D maps, thermal analysis (TG and DSC) and from the perspective of hydrogen sulfide air removal performance. To determine the process performances, the variables were: the nature of the cellulosic derivative–polypropylene hollow fiber composite membrane, the concentration of hydrogen sulfide in the polluted air, the flow rate of polluted air, and the pH of the cadmium nitrate solution. Pertraction efficiency was maximum for the sodium carboxymethyl–cellulose (NaCMC)-polypropylene hollow fiber membrane, a hydrogen sulfide concentration in the polluted air of 20 ppm, polluted air flow rate of 50 L/min, and a pH of 2 and 4.

The surface thermodynamic properties of polymers and copolymers modified by supramolecular structures are very used in several industrial processes, such as selective adsorption, paints, coatings, colloids, and adhesion applications. Background: Inverse gas chromatography at infinite dilution was proved to be the best technique to determine the surface properties of solid surfaces by studying the adsorption of some model polar and non-polar organic molecules adsorbed on solid surfaces by varying the temperature. Methods: The retention volume of adsorbed solvents is a precious parameter to obtain the London dispersive and polar free energies and the London dispersive surface energy of styrene–divinylbenzene copolymer modified by supramolecular structure of melamine using the Hamieh thermal model and our new methodology consisting in the separation of the two polar and dispersive free energy of interaction. This led to the determination of the polar acid and base surface energy, and the Lewis’s acid-base constants of the various solid materials. Results: all surface energetic properties of styrene–divinylbenzene copolymer modified by melamine at different percentages were determined as a function of temperature, following our new methodology. Conclusions: It was observed that the styrene–divinylbenzene copolymer exhibited the highest London dispersive surface energy which decreased when the melamine percentage increased. All materials presented higher Lewis’s basicity and this Lewis’s basicity increased with the percentage of melamine.

The world is struggling with the increasing rate at which water bodies are constantly polluted due to rapid modernization and industrialization. The different types of water contaminants include both anthropogenic and natural contaminants. Environmentalists are mainly concerned about heavy metals such as cadmium ions, as they are considered poisonous and carcinogenic even if they are present at a minimum concentration, and they are considered an immediate concern, according to the World Health Organization. Recently, many methods, such as solvent extraction, ion exchange, electrochemical precipitation, and reverse osmosis, have been developed to remove heavy metals from wastewater. These methods have been reported to be expensive and inefficient; hence, more cost-effective and eco-friendly alternative strategies are needed. Amidst these challenges, a ray of hope emerges in the form of biosorbents. These abundant, eco-friendly, and cost-efficient materials have shown promise as an alternative method for removing heavy metals from wastewater. They are equipped with functional groups that can effectively absorb metal ions onto their surfaces, offering a potential solution to our water contamination woes. This review is significant as it delves into the potential use of several biosorbents to decontaminate cadmium ions from wastewater. This review is significant as it delves into the potential use of several biosorbents to decontaminate cadmium ions from wastewater

The erosion of surface pipelines induced by proppant flowback during shale gas production is significant. The surface pipelines in a shale gas field in the Sichuan Basin experienced perforation failures after only five months of service. To investigate the erosion features of L360N, coatings, and ceramics and optimize the selection of two protective materials, a gas-solid two-phase flow jet erosion experimental device was used to explore the erosion resistance of L360N, coating, and ceramic under different impact velocities (15 m/s, 20 m/s, and 30 m/s). An energy dispersive spectroscope, a scanning electron microscope, and a laser confocal microscope were employed to analyze erosion morphologies. With the increase in flow velocity, erosion depth and erosion rate of L360N, coating, and ceramic increased and peaked under an impact velocity of 30 m/s. Maximum erosion rate and maximum erosion depth of L360N were respectively 0.0350 mg/g and 37.5365 µm. Its primary material removal mechanism was plowing of solid particles and microcracks were distributed on the material surface under high flow velocities. Maximum erosion rate and maximum erosion depth of coating were respectively 0.0217 mg/g and 18.9964 µm. Its primary material removal mechanism was the detachment of the binder phase Co caused by plowing. Maximum erosion rate and maximum erosion depth of ceramics were respectively 0.0108 mg/g and 12.4856 µm. The erosion mechanisms were micro-cutting and plowing. Under different particle impact velocity, different erosion morphologies were observed, but the primary erosion mechanism was the same. The erosion resistance of ceramics was higher than that of coating. Therefore, ceramic lining materials could be used to protect the easily eroded parts, such as pipeline bends and tees, and reduce the failure rate by more than 93%. The study provided the data and theoretical basis for the theoretical study on oil and gas pipeline erosion and pipeline material selection.

The goal of this work was to develop the acrylonitrile-butadiene (NBR) elastomer composites filled with hydroxyapatite (HAP), which were characterized with improved cure characteristics and burning resistance. Silane, i.e., (3-aminopropyl)-triethoxysilane, ionic liquid, i.e., 1-decyl-3-methylimidazolium bromide and surfactant, i.e., cetyltrimethylammonium bromide, were used to improve the filler’s dispersibility in the elastomer matrix and to reduce the time and temperature of vulcanization. The effect of HAP and dispersants on the cure characteristics, crosslink density and physico-chemical properties of NBR composites was explored. The additives used, especially the ionic liquid and surfactant, effectively improved the dispersion of HAP in NBR matrix. The amount of HAP and the dispersant used strongly affected the cure characteristics and crosslink density of NBR. The optimal vulcanization time significantly increased with HAP content and was pronouncedly reduced when ionic liquid and surfactant were applied. In addition, ionic liquid and surfactant significantly lowered the onset vulcanization temperature, improved the crosslink density and hardness of the vulcanizates, while impairing their elasticity. HAP and dispersants did not significantly affect the damping properties and chemical resistance of NBR vulcanizates. Above all, application of HAP considerably enhanced the resistance of vulcanizates to thermo-oxidative aging and reduced their flammability compared to the unfilled NBR.

Pipelines extend thousands of kilometers to transport and distribute oil and gas. Given the challenges often faced with corrosion, fatigue, and other issues on steel pipes, the demand for glass fiber reinforced plastics (GFRP) pipes is increasing in the oil and gas gathering and transmission systems. However, the medium transported through these pipelines contains multiple acid gases such as CO2 and H2S, as well as ions including Cl-、Ca2+、Mg2+、SO42-、CO32- and HCO3-. These substances can cause a series of problems, such as aging, debonding, delamination, and fracture. In this study, a series of aging damage experiments were conducted on V-shaped GFRP pipes with depths of 2mm and 5mm. The aging and failure of GFRP were studied under the combined effects of external force and acidic solution using acoustic emission (AE) techniques. It was found that the acidic aging solution promoted matrix damage, fiber/matrix desorption, and delamination damage in GFRP pipes over a short period. However, the overall aging effect was relatively weak. Based on the experimental data, the SSA-LSSVM algorithm was proposed and applied to the damage pattern recognition of GFRP. An average recognition rate of up to 90% was achieved, indicating that this method is highly suitable for analyzing AE signals related to GFRP damage.

The application possibilities of austenitic stainless steels in high friction, abrasion and sliding wear conditions are limited by their inadequate hardness and tribological characteristics. In order to improve these properties, thermochemical treatment of their surface by plasma nitriding is suitable. This article is focused on corrosion resistance of the conventionally plasma nitrided AISI 304 stainless steel (530 °C, 24 hours) in 0.05 M and 0.5 M sodium chloride solutions at room temperature (20 ± 3 °C), tested by potentiodynamic polarization and electrochemical impedance spectroscopy. The optical microscopy, scanning electron microscopy, energy-dispersive X-ray spectroscopy and X-ray photoelectron spectroscopy are used for the nitrided layer characterization. The experiment results point to a significant reduction in corrosion resistance after performed plasma nitriding even in a solution with a very low chloride concentration (0.05 mol/L).

Herein, we investigated hydrogels composed of boronic Acid functionalized alginate and blended with polyvinyl alcohol of different molecular weights to control the release of metoclopramide hydrochloride (MTC) as a function of pH and shear stress. The functionalization of alginate introduced dynamic covalent bonding and pH-responsive properties that can modulate network connectivity. The study investigated the viscoelastic properties of the hydrogels, their drug release profiles, and their responsiveness to changes in pH and shear forces. The results showed higher PVA molecular weight and alkaline pH conditions increased hydrogel viscosity and stiffness due to a more stable and interconnected network structure than acidic pH. Metoclopramide release revealed that the hydrogels exhibited pH-responsive drug release behavior. The drug was more readily released under acidic conditions due to the instability of sp2-hybridized boronate ester bonds. The influence of shear forces on the release of metoclopramide was also investigated at shear rates of 1, 10, and 100 s-1, revealing their effect on matrix stiffening. The research shows that AlgBA/PVA hydrogels have unique properties, such as dynamic covalent bonding, that make them sensitive to external mechanical forces. This sensitivity makes them ideal for applications where physiological conditions trigger drug release

This study investigates the properties of solution processed hybrid pol-yimide, PI nanocomposites containing a variety of nanofillers, including polyaniline copolymer modified clay, PNEA, nanographene sheets, NGS, and carbon nanotube sheet, CNT-PVDF, respectively. Through a series of experiments, the flow behavior of poly(amic acid), PAA solution and PAA suspension containing polyaniline copolymer modified clay, PNEA was determined as a function of the shear rate, processing temperature and polymerization time. It is shown that the neat PAA solution exhibited a complex rheological behavior ranging from shear thickening to New-tonian behavior with increasing shear rate and testing temperature. The presence of modified clay in PAA solution significantly reduced the viscosity of PAA. Differential Scanning Calorimetry (DSC) analysis show that polyimide-nanographene sheets, PI NGS nanocomposites processed at high spindle speed (100 rpm) had lower total heat of decomposition which is indicative of improved fire retardancy. The effect of processing temperature on the specific capacitance of polyimide-CNT-PVDF composites containing electrodeposited polypyrrole fillers was determined by using cyclic voltammetry, CV. It was shown that the hybrid composite working electrode material processed at 90˚C produced a remarkably higher overall stored charge when compared to the composite electrode material processed at 250˚C. Consequently, the specific capacitance ob-tained at a scan rate of 5 mV/s for the hybrid nanocomposite processed at 90°C was about 858 F/g after 1 cycle, which is about 6.3 times higher than the specific capacitance of 136 F/g produced by the hybrid nanocomposite processed at 250°C. These findings show that the properties of the hybrid nanocomposites are remarkably influenced by the processing conditions and highlights the need for process optimization.

Polymeric composites are prone to undergo damage, such as microcracks, during their operation, that can ultimately lead to catastrophic failure. To contradict such problem, effort has been put, by the scientific community, towards developing self-healing composites that, by mimicking biological systems, can autonomously and prematurely repair flaws, extending durability and improving security of materials. The present review explores the progress being made in such area, focusing on extrinsic self-healing methods, considering that they can be employed to a variety of materials. Reservoir-based techniques, that resort to capsules, hollow fibers or microvascular networks, and thermoplastic-based ones are overviewed, prioritizing innovative approaches made in recent years. At last, promising practical applications for self-healing composites are highlighted and future challenges and opportunities are pointed out.

The development of novel ionic liquid crystals for energy storage applications has gained significant attention in recent years due to their potential to develop the field of energy storage. Ionic liquid crystals represent a unique class of materials with high ionic conductivity and thermal stability, making them ideal candidates for use in advanced energy storage devices. This research aims to explore the fundamental properties, structure and liquid crystals performance of these novel materials, with the goal of advancing their practical application in next-generation energy storage technologies. By understanding the structure-function relationship of ionic liquid crystals, researchers can tailor their properties to meet specific energy storage requirements, such as high energy density, fast charging capabilities, and long cycle life. This study seeks to contribute to the growing body of knowledge in the field of energy storage by investigating the potential of novel ionic liquid crystals as efficient and sustainable energy storage solutions. The two ionic liquid crystals show mesomorphic behavior and typical zwitterion characteristics that revealed by the cyclic voltammetry techniques. These materials uploaded with lithium ions for more stability and higher ionic conductivity.

Electronic skin is widely employed in multiple applications such as health monitoring, robot tactile perception, and bionic prosthetics. In this study, we fabricated millimeter-scale electronic skin featuring compact sensing units using Boston Micro Fabrication S130 (a high-precision additive manufacturing device) and the template removal method. We used a gallium-based liquid metal and achieved an inner channel diameter of 0.1 mm. The size of the sensing unit was 3 × 3 mm². This unit exhibited a wide linear sensing range (10–22000 Pa) and high pressure resolution (10 Pa) even on an ultracurved surface (radius of curvature was 6 mm). Sliding was successfully detected at speeds of 8–54 mm/s. An artificial nose with nine sensing units was fabricated, and it exhibited excellent multitouch and sliding trajectory recognition capabilities. This confirmed that the electronic skin functioned normally even on an ultracurved surface.

The work presents the results of studying dilute aqueous solutions of commercial Ln(NO3)3 · xH2O salts with Ln=Ce-Lu using X-ray diffraction (XRD), IR spectroscopy, X-ray absorption spectroscopy (XAS: EXAFS/XANES) and pH measurements. As a reference point, XRD and XAS measurements for characterized Ln(NO3)3 · xH2O microcrystalline powder samples were performed. The local structure of Ln-nitrate complexes in 20 mM Ln(NO3)3 · xH2O aqueous solution was studied under total external reflection conditions and EXAFS geometry was applied to obtain high-quality EXAFS data for solutions with low concentrations of Ln3+ ions. Results obtained by EXAFS spectroscopy showed significant contraction of the first coordination sphere during the dissolution process for metal ions located in the middle of the lanthanide series. It was established that in Ln(NO3)3 · xH2O solutions with Ln=Ce, Sm, Gd, Yb (c=134, 100, 50 and 20 mM) there are coordinated and, to a greater extent, non-coordinated nitrate groups with bidentate and predominantly monodentate bonds with Ln ions, the number of which increases upon transition from cerium to ytterbium. Cross-relationships between the concentration of solutions, pH value and antimicrobial activity with the type of Ln = Ce, Sm, Gd, Yb were established, as well as the absence of biocidal properties of solutions with a concentration of 20 mM, except for Ln = Yb. The important role of experimental conditions in obtaining and interpreting the results was noted.

In this paper, a novel microwave catalyst Ni@SiC/CNFs (NSC), C/Ni (NC), and C/SiC (SC) were successfully synthesized by electrostatic spinning method, and proved to degrade methylene blue with high efficiency under microwave irradiation. The results imply that the catalyst Ni@SiC/CNFs with double shell structure gave a 99.99 % removal rate in 90 s for the degradation of methylene blue under microwave irradiation, outperformed the C/Ni and C/SiC and most other reported catalysts in similar studies. On the one hand, the possible mechanism of the methylene blue degradation should be ascribed to that double shell structure increases the polarization source of the material, resulting in excellent microwave absorption properties; and on the other, the in-situ generation of active species OH• and O2 - under microwave radiation and the synergistic coupling effect of metal plasma greatly improved the degradation efficiency of methylene blue. The findings of this study could provide a valuable reference for the green degradation of industrial dye wastewater and its sustainable development process.

This study presents, for the first time, the development of fibers with favorable properties for biodegradable wound dressings made from the Ecovio® (EC) polymer blend, composed of poly(lactic acid) (PLA) and poly(butylene adipate-co-terephthalate) (PBAT), incorporated with tea tree essential oil (TTE). TTE presented antimicrobial activity against Pseudomonas aeruginosa and Staphylococcus aureus, achieving minimal inhibitory concentrations of 15 and 7.5 mg/mL, respectively. The TTE was mixed with EC in a binary chloroform and formic acid (85/15 v/v) mixture, leading to homogeneous and wettable fibers by electrospinning. The EC/TTE fibers were characterized confirming the TTE in the fibers. The tests showed that TTE (0.5, 1.0 or 1.5 mL) improved the polymer blend electrospinnability. TTE (1.5 mL or 75 w% concerning the EC) lead to homogeneous fibers with an average diameter of 278 nm. TTE (75 w%) increased the wettability of the EC fibers from 120±2° to 69±1°. Preliminary bacterial adhesion and proliferation assays demonstrated that the EC/TTE fibers have anti-adhesive activity e seems to be more toxic against P. aeruginosa compared to S. aureus after 24 hours of incubation. Compatibility tests with human blood indicated that the EC/TTE fibers accelerate blood coagulation. The EC/TTE fibers exhibit promising chemical and biological properties (in vitro) for the development of wound dressings.

This work presents the results regarding the synthesis of tungsten nanoparticles (W NPs) by magnetron sputtering combined with gas aggregation (MSGA) when H2 mixed with Ar is used as working gas, the amount of H2 being increased up to 82%. The results show that up to 40% H2 in discharge the synthesis rate increases over 60 times, rapidly decreasing for over 50% H2 in discharge. The W dust is still produced in H2 dominated discharge (82%), the deposition rate being small but not negligible (20 mg/hour). The obtained WNPs are isolated, with the diameter decreasing from 50 nm to 15 nm when the amount of H2 in discharge is smaller than 41%. Over this value, the particles tend to agglomerate, forming structures similar to film-like deposits. Also, the diameter of the deposited spots on substrates is dependent on the H2 content in discharge. This allows the efficient coating of substrates with dimensions up to 26 mm by translating them in front of the MSGA cluster source exit aperture. Supplementary, for 41% H2 in discharge, the influence of synthetic air leaks (0-5%) in discharge was investigated. The deposition rate decreases rapidly (ceasing for around 4% air in discharge) and the obtained nanoparticles tend to agglomerate (at 2% air content, the dust deposit has the aspect of a near continuous film). Chemical composition investigations show a pronounced tendency of oxidation, nitridation and oxynitride formation in the presence of air leaks.

A low cost, scalable and robust process has been proposed as innovative method for coating solar mirrors with a self-cleaning, transparent in the full solar range and versatile material based on auxetic aluminium nitrides, previously obtained on the laboratory scale. This work presents the scaling-up of fabrication process from laboratory to prototypal scale and pre-liminary results of outdoor self-cleaning solar mirror prototypes testing in the demonstrative CSP plant ENEASHIP located in Casaccia (Rome) ENEA research centre. Prototypes 50x40cm have shown stability in external conditions: no degradation occurs during the test campaign. Their washing restores the initial reflectance affected by soiling and the self-cleaning performance allows the utilization of a reduced quantity of water for cleaning operations with respect to uncoated glass of back surface mirrors. A similar self-cleaning AlN coating could be utilized on other solar components affected by soiling, such as glass envelopes of heat collecting elements, PV panels and everywhere are required self-cleaning performance combined to optical ones.

The presented work offers a novel process scheme for valorizing historical Pb-Zn slag, which involves crushing, grinding, and then using separation techniques to concentrate valuable components (nonferrous metals). This methodology could have a significant impact on the global beneficiation of metallurgical slags since, in theory, it is significantly more simple, environmentally friendly, and cost-effective than standard pyrometallurgical or hydrometallurgical procedures. According to previous physicochemical and mineralogical studies, Pb-Zn slag from "Topilnica" Veles is a valuable secondary raw material. This inhomogeneous technogenic resource contains substantial amounts of nonferrous metals (Pb, Zn, Cu, and Ag). However, laboratory tests have indicated that the Pb-Zn slag contains a very uneven valuable metals amounts, ranging from several g/ton to several tens of g/ton. The main issue is that traditional metallurgical procedures for releasing beneficial elements are not commercially viable since the valuable elements are "trapped" within amorphous aluminosilicates or intergrowths of alloy grains and glassy phases. Gravity concentration (Wilfley 13 shaking table) and magnetic separation (Davis separator and disk separator) were used to obtain the final concentrate following comminution and grindability testing. The gravity concentration proved more effective. This streamlined approach of valorizing Pb-Zn slag can reduce the need for hazardous chemicals used in hydrometallurgical refinement operations, as well as the extremely high temperatures required for pyrometallurgical processing. This is the first investigation into the feasibility of this novel approach, which includes direct investigations of the Pb-Zn slag feed using these alternative technologies. After extracting the valuable metals, the amorphous aluminosilicate part of the Pb-Zn slag can be reapplied as an alternative raw material in the building sector, adding to the circularity of the suggested approach..

Due to their remarkable intrinsic physical properties, carbon nanotubes (CNTs) can enhance mechanical properties and confer electrical and thermal conductivity to polymers currently investigated for use in advanced applications based on thermal management. An epoxy resin filled with varying concentrations of CNTs (up to 3 wt.%) was produced and experimentally characterized. The electrical percolation curve identified two critical filler concentrations: 0.5 wt%, near the electrical percolation threshold, suitable for exploring mechanical and piezoresistive properties, and 3 wt% for investigating thermo-electric properties due to the Joule effect with applied voltages ranging from 70V to 200V. Numerical models were developed using multiphysics simulation software. Once validated with experimental data, these models were used to investigate additional physical properties of the composites. Furthermore, a statistical approach based on the design of experiments (DoE) was employed to examine the influence of certain thermal parameters on the final performance of the materials. The purpose of this research is to promote the use of contemporary statistical and computational techniques alongside experimental methods to enhance understanding of materials science. New materials can be identified through these integrated approaches, or existing ones can be more thoroughly examined.

The article presents the results of research work devoted to the study of composite materials on polymer binder with the content of modified mineral filler - water-dispersion paint and varnish materials on acrylic polymer with modified filler - diatomite. The aim of the study is to obtain polymer-based composites with modified diatomite (water-dispersion paint on acrylic binder) with improved performance properties. Methods: determination of porosity, adhesion, elasticity, hiding power of the control composition; determination of porosity, adhesion, elasticity, hiding power of the obtained composites with the use of modified filler; investigation of the influence of radiation in the infrared radiation (IR) region of the spectrum of the paint coating surface using FLIRB620 thermal imager. As a result of work it is noticed that modification of water dispersions by silica activated diatomite promotes elimination of the main disadvantages of materials and coatings on the basis of acrylate binder - low water resistance and low physical and mechanical characteristics, introduction of modified diatomite into water emulsion paint on acrylate basis does not lead to deterioration of the main operational characteristics of paint and varnish coatings - porosity, adhesion, elasticity and covering. When analyzing the effect of emissivity in the IR region of the spectrum of the paint coating surface, a significant effect of the quantitative content of modified diatomite on the reduction of emissivity of paint coatings in the IR region of the spectrum was established and it was shown that a significant effect of the reduction of emissivity of paint coatings in the IR region of the spectrum is provided by the introduction of modified diatomite in the amount of 40 wt.h. into the mixture. The influence of the time of full-scale tests in the investigated small range regardless of the quantitative composition of modified diatomite on the performance characteristics of the paintwork was established.

Biodiesel has several drawbacks, such as being prone to oxidation, having reduced stability, and having limited storage time. Antioxidants compatible with biodiesel are being used to address its drawbacks. Utilizing antioxidants effectively improves the quality of biodiesel. Enhancing the quality of biodiesel for use as a clean energy source benefits both the global economy and ecology. Therefore, we believe that our work will contribute to the advancement of the worldwide industry. The study used blends consisting of 20% biodiesel and 80% diesel fuel. Isatin-thiosemicarbazones were tested as additives in blends at a concentration of 3000 parts per million (ppm) using an oxifast device. Comparing them to the chemical antioxidant Trolox. FT-IR, DSC, and TGA were used to characterize these samples. DSC measured sample crystallization temperatures (Tc). Samples with antioxidants showed decreased values compared to the non-antioxidant diesel sample D100. Several DSC tests were conducted to determine the antioxidant strengths of various samples. The results showed that the FT-IR spectrum's antioxidant effect regions grow clearer with antioxidants. The extra antioxidant is effective. Biodiesel's oxidative stability improves with isatin-thiosemicarbazones at varying concentrations. The kinetics of thermal decomposition of isatin-thiosemicarbazones under non-isothermal conditions have been determined using the Kissinger, Ozawa, and Boswell techniques. The activation energies of compounds 1 and 2 were calculated 137–147 kJ mol^-1 and 173–183 kJ mol^-1, respectively.

Solid polymer electrolytes and composite polymer electrolytes serve as crucial components in all-solid-state energy storage devices. Structural batteries and supercapacitors present a promising alternative for electric vehicles, integrating structural functionality with energy storage capability. However, despite their potential, these applications are hampered by various challenges, particularly in the realm of developing new solid polymer electrolytes that require more investigations. In this study, novel solid polymer electrolytes and composite polymer electrolytes were synthesized using epoxy resin blends, ionic liquid, lithium salt, and alumina nanoparticles, and subsequently characterized. Among the formulations tested, the optimal system, designated as L70P30ILE40Li1MAl2 and containing 40 wt.% of ionic liquid and 5.7 wt.% of lithium salt, exhibited exceptional mechanical properties. It displayed a remarkable storage modulus of 1.2 GPa and reached ionic conductivities of 0.085 mS/cm at 60°C. Furthermore, a proof-of-concept supercapacitor was fabricated, demonstrating the practical application of the developed electrolyte system.

High entropy alloys have excellent wear resistance, so they have great application prospects in the fields of wear resistance and surface protection. In this study, the wear resistance of FeNiCrCoCu high entropy alloy coating was systematically analyzed by molecular dynamics method. FeNiCrCoCu high entropy alloy was used as a coating material to adhere to the surface of Cu matrix. The friction and nano indentation simulation of this coating material were carried out by controlling the ambient temperature. The influence of temperature on its friction properties was analyzed from five aspects: lattice structure, dislocation evolution, friction coefficient, hardness and elastic modulus. The results show that with the increase of temperature, the disorder of the lattice structure increases, which leads to the increase of the tangential force and the friction coefficient in the friction process. At 300K and 600K, the ordered lattice structure of the high entropy alloy coating material is basically the same, and thus their hardness is basically the same. However, the dislocation density at 600K is significantly reduced compared with that at 300K, resulting in the increase of the elastic modulus of the material from 173GPa to 219GPa. At the temperatures of 900K and 1200k, lattice disorder take place rapidly, and dislocation density also decreases significantly, resulting in a significant decrease in the hardness and elastic modulus of the material. When the temperature reaches 900K, the wear resistance of the FeNiCrCoCu high entropy alloy coating decreases sharply. This work is of great value to the analysis of wear resistance of high entropy alloy at high temperature.

Potential permanent magnet (Fe0.7Co0.3)2B has large saturation magnetization and high Curie temperature but a moderate magnetocrystalline anisotropy (MCA) and displays relatively low coercivity. One way to improve coercivity is to combine the contribution from magnetocrystalline- and magnetic shape anisotropy by preparing (Fe0.7Co0.3)2B nanowires. We study the effect of size, morphology, and surface defect on the hard magnetic properties of nanowires using micromagnetic simulation. The hard magnetic properties of (Fe0.7Co0.3)2B nanowire bonded magnet have been estimated, including the role of inter-wire magnetostatic interaction. By considering the existence of local reduction of MCA energy up to 30% on the surface layer of nanowires, the anisotropic bonded magnet with 65% vol. of (Fe0.7Co0.3)2B nanowires displays typical magnetic properties of remanence Br=8.4 kG, coercivity Hci=9.9 kOe, and maximum energy product (BH)m=17.8 MGOe. Developing effective technology for synthesizing nanowires and fabricating corresponding bonded magnets is promising for manufacturing practical magnets based on magnetic phase with relatively low or moderate MCA, such as (Fe0.7Co0.3)2B.

This study aimed to compare the flexural strength, surface roughness, and microhardness of a resin for three-dimensional (3D) printing and a conventional composite resin and to evaluate whether the printing orientation influences these properties. To evaluate the flexural resistance, test specimens were produced and divided into four groups: three groups of resins for 3D printing with inclinations of 0°, 45°, and 90°, and one group of conventional composite resin. Forty discs were produced and subjected to a sandpaper-polishing sequence, and the surface roughness was measured using a roughness meter. The Vickers microhardness test was performed at three different points, and the average was obtained. The results were subjected to ANOVA statistical analysis and Tukey's test. There were statistical differences in the flexural strength and microhardness between the conventional resin and the resin used for 3D printing. No statistical difference in surface roughness was observed. The resin for 3D printing exhibited lower flexural strength and microhardness than conventional composite resins. We concluded that the resin for 3D printing had lower flexural strength and hardness than the conventional composite resin but similar surface roughness. The printing orientation did not affect the flexural strength, whereas the hardness increased as the printing angle increased.

The safety concerns associated with current lithium-ion batteries are a significant drawback. A short-circuit within the battery's internal components, such as those caused by a car accident, can lead to ignition or even explosion. To address this issue, a polymer shear thickening electrolyte, free from flammable solvents, has been developed. It comprises a star-shaped oligomer derived from a trimethylolpropane (TMP) core and polyether chains, along with the inclusion of 20 wt.% nanosilica. Notably, the star-shaped oligomer serves a dual function as both the solvent for the lithium salt and the continuous phase of the shear thickening fluid. The obtained electrolytes exhibit an ionic conductivity of 10-6 S cm-1 at 20 °C and 10-4 S cm-1 at 80 °C, with a high Li+ transference number (t+ = 0.79). A nearly thirtyfold increase in viscosity to a value of 1187 Pa s at 25 °C and a critical shear rate of 2 s-1 were achieved. During impact, this electrolyte could enhance cell safety by preventing electrode short-circuiting.

Nitrogen oxides (NOx), pivotal atmospheric pollutants, significantly imperil the environment and human health. The CH4-SCR process, leveraging the abundant and accessible methane (CH4), emerges as a promising avenue for NOx abatement. Previous studies have demonstrated that zeolite support with twelve-membered ring (12-MR) and five-membered ring (5-MR) structures are susceptible to framework collapse in the presence of water, leading to catalyst deactivation. Consequently, there is a necessity to explore novel zeolites with enhanced hydrothermal stability for application in CH4-SCR processes. This research introduced for the first time an investigation into a novel In-H-SSZ-39 catalyst, synthesized via ion exchange and meticulously optimized for preparation conditions, including calcination temperature, In ions concentraiton, and reaction conditions, including CH4/NO ratio, O2 concentration, water vapor content, and Gas hourly space velocity (GHSV). Notably, the In/H-SSZ-39 catalyst achieved superior performance of 42.1% at 605 °C, with a calcination temperature of 500 °C and an In ion concentration of 0.066 M, under CH4/NO ratio of 1.5:1, 10% O2, and GHSV of 21000 h-1. In addition, the catalytic performance was influenced by the concentration of water vapor and the GHSV value.

The rational design of magnetic carbon composites, encompassing both composition and microstructure, holds significant potential for achieving exceptional electromagnetic wave absorbing materials (EAMs). In this study, FeCo@CM composites was efficiently fabricated through an advanced microwave plasma assisted reduction chemical vapor deposition (MPARCVD) technique, offering high efficiency, low cost, and energy-saving benefits. By depositing graphitized carbon microspheres, the dielectric properties were significantly enhanced, resulting in improved electromagnetic wave absorption performances through optimized impedance matching and a synergistic effect with magnetic loss. A systematic investigation revealed that the laminar-stacked structure of FeCo exhibited superior properties compared to its spherical counterpart, supplying a higher number of exposed edges and enhanced catalytic activity, which facilitated the deposition of uniform and low-defect graphitized carbon microspheres. Consequently, the dielectric loss performance of the FeCo@CM composites was dramatically improved due to increased electrical conductivity and the formation of abundant heterogeneous interfaces. At a 40 wt% filling amount and a frequency of 7.84 GHz, the FeCo@CM composites achieved a minimum reflection loss value of -58.2 dB with an effective absorption bandwidth (fE) of 5.13 GHz. This study presents an effective strategy for developing high-performance EAMs.

Artificial intelligence methods, especially artificial neural networks (ANNs), have increasingly been utilized for the mathematical description of physical phenomena in (metallic) material processing. Traditional methods often fall short in explaining the complex, real-world data ob-served in production. While ANN models, typically functioning as "black boxes," improve pro-duction efficiency, a deeper understanding of the phenomena, akin to that provided by explicit mathematical formulas, could enhance this efficiency further. This article proposes a general framework that leverages (CAE) ANNs to explain predicted results alongside their graphical presentation, marking a significant improvement over previous approaches and those relied on expert assessments. Unlike existing Explainable AI (XAI) methods, the proposed framework mimics the standard scientific methodology, utilizing minimal parameters for the mathematical representation of physical phenomena and their derivatives. Additionally, it analyzes the relia-bility and accuracy of the predictions using well-known statistical metrics, transitioning from deterministic to probabilistic descriptions for better handling of real-world phenomena. The proposed approach addresses both aleatory and epistemic uncertainties inherent in the data. The concept is demonstrated through the hot extrusion of aluminum alloy 6082, where CAE ANN models and predicts key parameters, and ChatGPT explains the results, enabling researchers and/or engineers to better understand the phenomena and outcomes obtained by ANNs.

The stability issues in the widely known organic inorganic halide perovskite, CH₃NH₃PbI_3, lead to the development of alternative halide double perovskite materials which get great attention in recent times. Although the stability issue seems promising, both materials and device performance of these photovoltaic materials remain inferior and challenging for improvements. Furthermore, the power conversion efficiency of single junction organic inorganic halide perovskite is now 24.2% and 29.15% for textured monolithic perovskite/silicon tandem solar cell, but for all-inorganic halide perovskite solar cell is 7.11% and halide double perovskite solar cells based on Cs₂AgBiBr₆ and Cs₂TiBr₆ is 2.8% and 3.3%, respectively, which is far less than 24.2% and 29.15%, respectively. This creates big question and concern that can both all-inorganic halide perovskite solar cell and halide double perovskites solar cells really be an acceptable alternatives to replace organic inorganic halide perovskite solar cells or lead based perovskite solar cells in the market in order to realize the sustainable practical applications? Not only this concern, but also there are many other big challenges facing by halide double perovskite solar cells. Such big challenges include: a) geometric constraints and limited integration with interfacial materials, b) dynamic disorder and a wide band gap and localized conduction band caused by cubic unit cell which restrains the interactions of orbitals, c) high processing temperature which may limit on the diverse applications, d) low electronic dimensionality making them less appropriate for single junction solar cell purpose and etc. Moreover, origin of electronic and optical properties such as the polarizability, the presence of molecular dipoles and their influence on the dynamics of the photo-excitations in the halide double perovskites remains unlock concern that need to be elucidated. Now, another big question is how to develop overcoming mechanisms for such challenges. Can we really overcome these current limitations faced by halide double perovskites so that we use them for sustainable commercialization? This research roadmap for performance improvement is suggested focusing on: materials surface and bulk engineering, band gap engineering, interfacial engineering, composition engineering, doping engineering, device architectural engineering, polar and domain order engineering. This was the reason that this review was developed in order to forward great contributions to the readers and commercial ventures.

Amyloid self-assembled from amyloid peptides βΑ40 or βΑ42 is notorious for its neurotoxic effects in plaque and neurofibrillary tangle formations leading to neuron dysfunction and diseases of cognitive decline (e.g. Alzheimer’s, Parkinson’s and Huntington's disease). This contrasts with so-called functional amyloids which are non-toxic ordered template structures amenable to applications in tissue engineering. Amyloid fibrils of variable morphology including long and hollow fibres and flattened tube and spiral ribbon-like structures have been used in engineering applications in nano-biology. Protein assemblies based on amyloid core structures display diverse biological functionalities could be applied in futuristic self-assembling biomaterials in nano-electronics. These possibilities have revolutionized the development of next generation computers and biosensors, ultracapacitors, memristors, actuators, molecular switches and could also be used to develop artificial synapses. Amyloid fibril assemblies have also been used in photoelectric and photon capture light harvesting technologies and been applied in innovative nano-photoelectronics and photovoltaics. Hybrid Aβ(16–22)-α-synuclein amyloid fibrils also exhibit light-harvesting and electron-transfer properties. Engineered amyloid assemblies are thus facilitating innovative futuristic advances in nano-technology. Furthermore, with a better understanding of amyloid fibril assembly processes it may be possible to develop therapeutic methods that prevent the toxic build up of this polymer in brain tissues that leads to diseases of cognitive decline. With the ever-expanding prevalence of these diseases in the ageing general global population, there certainly is a clear and present need to find a remedy for these debilitating conditions.

This paper presents the fabrication and characterization of cylindrical capacitors utilizing magnetodielectric materials composed of magnetizable microfibers dispersed within a silicone oil matrix. The microfibers, ranging in diameter from 0.25 to 2.20 μm, comprise hematite (α-Fe2O3), maghemite (γ-Fe2O3), and magnetite (Fe3O4). The study investigates the electrical behavior of these capacitors under the influence of an external magnetic field superimposed on a medium-frequency alternating electric field, across four distinct volume concentrations of microfibers. Electrical capacitance and resistance measurements are conducted every second over a 60-second interval, revealing significant dependencies on both the quantity of magnetizable phase and the applied magnetic flux density. Furthermore, the temporal stability of the capacitors’ characteristics is demonstrated. The obtained data are analyzed to determine the electrical conductance and susceptance of the capacitors, elucidating their sensitivity to variations in microfiber concentration and magnetic field strength. To provide theoretical insight into the observed phenomena, a model based on dipolar approximations is proposed. This model effectively explains the underlying physical mechanisms governing the electrical properties of the capacitors. These findings offer valuable insights into the design and optimization of magnetodielectric-based capacitors for diverse applications in microelectronics and sensor technologies.

Flexible electronics have revolutionized the field by overcoming the rigid limitations of traditional devices, offering superior flexibility and adaptability. Conductive ink performance is crucial, directly impacting the stability of flexible electronics. While metal filler-based inks exhibit excellent conductivity, they often lack mechanical stability. To address this challenge, we present a novel conductive ink utilizing a ternary composite filler system: liquid metal and two micron-sized silver morphologies (particles and flakes). We systematically investigated the influence of filler type, mass ratio, and sintering process parameters on the composite ink's conductivity and mechanical stability. Our results demonstrate that flexible wires fabricated with the liquid metal/micron silver particle/micron silver flake composite filler exhibit remarkable conductivity and exceptional bending stability. Interestingly, increasing the liquid metal content results in a trade-off, compromising conductivity while enhancing mechanical performance. After enduring 5000 bending cycles, the resistance change in wires formulated with a 4:1 mass ratio of micron silver particles to flakes is only half that of wires with a 1:1 ratio. This study further investigates the mechanism governing resistance variation during flexible wire bending. Additionally, we observed a positive correlation between sintering temperature and pressure with the conductivity of flexible wires. The significance of sintering parameters on conductivity follows a descending order: sintering temperature, sintering pressure, and sintering time. Finally, we demonstrate the practical application of this technology by integrating the composite ink-based flexible wires with conductive polymer-based strain sensors. This combination successfully achieved the detection of human movements, including finger and wrist bending.

In this paper glass crystallization behavior of 50ZnO:47B2O3:3Nb2O3:0.5Eu2O3 (G-0h) glass has been investigated in detail by DSC, XRD and TEM analysis. The luminescent properties of resulted glass-ceramics were also investigated. By XRD and TEM analysis crystallization of several crystalline phases have been proved (α-Zn3B2O6, β-Zn3B2O6 and ZnNb2O6). By calculating of crystal parameters it was found that europium ions are successfully incorporated in the β-Zn3B2O6. Photo-luminescent spectra show an increased emission in the resulting glass-ceramic samples as compared with the parent glass sample because of the higher asymmetry of Eu3+ ions in the crystalline phases obtained. It was established that the optimum emission intensity is registered for glass-ceramic sample obtained after 25 hours heat treatment of the parent glass.

Non-woven jute (NWJ) produced from the carpet industry waste was oxidized by H2O2 or alkali treated by NaOH and compared with water-washed samples. Changes in the structure of the NWJ, tracked by XRD, showing that both chemical treatments disrupt hydrogen bond networks between cellulose Iβ chains of the NWЈ fibers. Thereafter, nano carbon nitride (nCN) was impregnated, using layer-by-layer technique, onto water washed jute sample (nCN-Jw), NaOH treated sample (nCN-Ja) and H2O2 treated sample (nCN-Jo). Analysis of the FTIR spectra of the impregnated samples, revealed that nCN anchors to the water washed NWЈ surface through hemicellulose and secondary hydroxyl groups of the cellulose. In the case of chemically treated samples nCN is preferentially bonded to the hydroxymethyl groups of cellulose. The stability and reusability of nCN-J samples were assessed by tracking the photocatalytic degradation of Acid Orange 7 (AO7) dye under simulated solar light irradiation. Results from up to ten consecutive photocatalytic cycles demonstrated varying degrees of effectiveness across different samples. nCN-Jo and nCN-Ja samples exhibited declining effectiveness over cycles, attributed to bond instability between CN and jute. In contrast, the nCN-Jw sample consistently maintained high degradation rates over ten cycles, with a dye removal percentage constantly above 90%.

Ab initio density functional theory molecular dynamics extensive calculations were used for the first time to evaluate stability conditions for relevant phases of InN. In particular, thermal decomposition of InN with formation of N2 molecules and pressure induced wurtzite – rocksalt solid-solid phase transition were established. The results consistent with available experimental data allowed a critical evaluation of potential and limitations of the proposed simulation method. The ab initio molecular dynamics as an efficient tool for simulations of phase transformations of InN including solid-solid structural transition and thermal decomposition with formation of N2 molecules has been demonstrated. It is of high interest because InN being important component of epitaxial quantum structures has still not been obtained as a bulk single crystal making difficult a determination of its basic physical properties and designing new applications.

The first treatments with dental implants had low success rates (75%). Nowadays, oral rehabilitation with titanium dental implants has a high success rate (95-98%). The success rate significantly increases due to increased scientific knowledge about osseointegration, changes in surgical techniques, and the development of implant surface treatments. Despite the high success rate of implants, no protocol defines the time for the prosthesis to be installed and loaded after surgery. This work compares a new dental implant's primary (mechanical) and secondary (osseointegration) stability. Dental implant with micro- and nano-roughness surface was placed in 24 patients with a minimum of 35 N.cm and a maximum of 60 N.cm. Primary stability was quantified with a torque wrench and Ostell Mentor. The secondary stability 45 and 60 days after surgery was measured with Ostell. The results showed no statistical difference in secondary stability at 45 and 60 days postoperatively among implants. The success rate of dental implants can be associated with the surface morphology with micro and nano-roughness and the shape of the fillets of the implant threads. When the manufacturer's guidelines are followed, it is possible to prosthetically rehabilitate the patient with an implant 45 days after surgery.

In this study, the mechanical and piezoresistive properties of mortars reinforced with carbon nanotubes (CNTs) and carbon micro fibers (CMFs) are determined. Silica fume as well as a polymer with polyalkylene glycol graft chains were used as dispersant agents for the CNTs and CMFs incorporation into the cement paste. The mechanical properties of the mortar composites were investigated in respect to their flexural and compressive strength. A four-probe method was used for the estimation of their piezoresistive response. The test outcomes revealed that the combination of the dispersant agents along with a low content of CNTs and CMF by weight of cement (bwoc) result in the production of a stronger mortar with enhanced mechanical performance and durability. More specifically, there was an increase in flexural and compressive strength up to 38% and 88%, respectively. Moreover, the piezoresistive response of the reinforced cementitious materials was attributed to the variation of electrical resistivity due to tunneling transport of electrons stemming from two different mechanisms due to the incorporation of the conductive admixtures (CNTs and CMF). This work aims to contribute to the progress acceleration in the field of developing structural materials with self-sensing and electrical actuation related properties.

Elemental sulfur, commonly known for its wide range of biological activity, has a long history of being used to protect all garden and vegetable crops from a range of pests and diseases, including powdery mildew, ascochyta blight, clubroot, plant mites, oidium, anthracnose, and scab. In the present study, a quick and environmentally friendly approach has been developed for the synthesis of sulfur nanoparticles with antibacterial activity. Sulfur nanoparticles (SNPs) were prepared by modifying the surface of elemental sulfur using various polyelectrolyte-surfactant mixtures (PSM) including NaCMC-SDBS and PHMG-CTAB. The SNPs were characterized by UV–visible spectrophotometry, X-ray diffraction (XRD), and thermogravimetric analysis (TG/DSC), scanning electron microscopy (SEM), with the SNPs showing an almost spherical shape with an average size in the range of 150-200 nm. The antibacterial activity of the sulfur nanoparticles was tested using against gram-positive S. aureus and E. faecium and gram-negative E. coli and P. aeruginosa bacteria. From this, it could be seen that SNPs exhibited significant antimicrobial activity against gram-positive bacteria, i.e., S. aureus and E. faecium. The in vitro cytotoxicity of the SNPs-1 and SNPs-2 studied to normal (MeT-5A) and tumorous (MCF-7) human cell lines was assessed in the concentration range from 500 μg/ml to 0.12 mg/ml, from which it was determined as being non-cytotoxic. The received products can be considered for potential application in agriculture and medicine.

In this article, the sol-gel method was used as a synthesis method, which shows the physico –chemical nature of the synthesis of a new complex material ferrit Li0.5MnFe1.5O4. The synthesized structure and structure were determined by the method of X-ray phase analysis. According to the analysis indicators, it was found that our compound is single-phase, spinel-structured, and syngony - cubic type. The microstructure of the compound and the quantitative composition of the elements contained were analyzed under a scanning electron microscope (SEM). Through a scanning electron microscope, Microsystems were taken from different parts of l Li0.5MnFe1.5O4-type crystallite, the elemental composition of crystals was analyzed, and the general type of surface layer of complex ferrite was shown. As a result, the fact that the compound consists of a single phase, the clarity of its construction was determined by the topography and chemical composition of the compound. As a result, it was found that the newly synthesized complex ferrites correspond to the Formula Li0.5MnFe1.5O4. The particles of the formed compounds have a large size (between 50.0 μm, 20.0 μm and 10.0 μm). Electro physical measurements were carried out on the LCR - 800 unit at intervals of 293-483 K and at frequencies of 1.5 and 10 kHz. The increase in frequency to 10 kHz led to a decrease in the value ε in the range of the studied temperature (293-483 K).

Self-healing materials research spans many academic disciplines and employs a wide range of methodologies. Some of the developed concepts are driven by the direct application of the materials. However, a deeper understanding of the basic mechanisms and principles of self-healing materials is still a challenging aim. Nature has mostly served as an inspiration for the development of new self-healing materials, and it will undoubtedly continue to be a significant source of inspiration for the creation of novel ideas. This review encompasses the principles of self-healing mechanisms based on the concepts of autonomous and non-autonomous procedures. Studies based on smart composite materials with autonomous self-healing properties are also included and discussed from two aspects of intrinsic or extrinsic abilities, taking into consideration their components and structures as well as the design of these composites. Finally, special attention is given to the application of the materials in several fields such as aerospace, automotive, marine, energy, medical and healthcare, military, and construction.

Materials engineering based on metal oxides for manipulating the solar spectrum and producing solar energy have been under intense investigation over the last years. In this work, we present NiO thin films double-doped with niobium (Nb) and nitrogen (N) as cation and anion dopants (NiO:(Nb,N)) to be used as p-type layers in all oxide transparent solar cells. The films were grown by sputtering a composite Ni-Nb target on room-temperature substrates in plasma containing 50% Ar, 25% O2 and 25% N2 gases. The existence of Nb and N dopants in the NiO structure was confirmed by the Energy Dispersive X-Ray and X-Ray Photoelectron Spectroscopy techniques. The nominally undoped NiO film, which was deposited by sputtering a Ni target and used as the reference film, was oxygen-rich, single-phase cubic NiO, having a visible transmittance of less than 20%. Upon double doping with Nb and N the visible transmittance of NiO:(Nb,N) film increased to 60%, which was further improved after thermal treatment to around 85%. The respective values of the direct band gap in the undoped and double-doped films were 3.28 eV and 3.73 eV just after deposition and 3.67 eV and 3.76 eV after thermal treatment. The changes in the properties of the films such as structural disorder, direct and indirect energy band gaps, Urbach tail states and resistivity were correlated with the incorporation of Nb and N in their structure. The thermally treated NiO:(Nb,N) film was used to form a diode with a spin-coated two-layer, mesoporous on top of a compact, TiO2 film. The NiO:(Nb,N)/TiO2 heterojunction exhibited visible transparency of around 80%, showed rectifying characteristics and the diode’s parameters were deduced using the I-V method. The diode revealed photovoltaic behavior upon illumination with UV light exhibiting a short circuit current density of 0.2 mA/cm2 and open-circuit voltage of 500 mV. Improvements of the output characteristics of the NiO:(Nb,N)/TiO2 UV-photovoltaic by proper engineering of the individual layers and device processing procedures are addressed. Transparent NiO:(Nb,N) films can be potential candidates in all-oxide ultraviolet photovoltaics for tandem solar cells, smart windows and other optoelectronic devices.

Graphene foam prepared by chemical vapor deposition method is a promising thermal interfacial material. However, the thermal properties of graphene foam highly depend on the experimental fabrication conditions during the chemical vapor deposition process. Aiming to reveal how to prepare the appropriate graphene foam for the various thermal management scenarios, the influence of experimental conditions on thermal properties of graphene foam is investigated. Furthermore, the contribution of thermal conductivity and thermal radiation to the effective thermal coefficient of graphene foam is carried out for comparison. Research results show that, the porosity and the cross-section shape of struts of growth template are two critical factors to affect the thermal transport of graphene foam, especially with the increase of temperature. In addition, the deposition time of graphene determines the wall thickness and affects the thermal conductivity directly. The thermal radiation contributes more than thermal conductivity when the temperature climbs continuously. Comparatively, the effective thermal coefficient of graphene foam composite with high porosity and circular shape struts is much superior to others at high temperature. The research findings can provide important guidance for the graphene foam fabrication and its applications in the field of thermal management.

Integrating nanomaterials like carbon nanotubes (CNTs) and iron oxide (Fe₃O₄) into epoxy composites has significant interest due to their potential to enhance mechanical properties. This study evaluates the impact of dispersion quality on the mechanical performance of CNT/Fe₃O₄/Epoxy composites, comparing stirring and sonication methods at three different loadings: 0.1, 0.3, and 0.5 wt.%. Tensile testing revealed that sonicated composites consistently outperformed stirred composites, with a significant increase in elastic modulus and ultimate tensile strength (UTS). However, fracture strain decreased in both composite types compared to pure epoxy, with sonicated composites experiencing a more significant reduction than stirred composites. These results underscore the importance of high-quality dispersion for optimizing mechanical properties.

This study introduces an innovative approach to designing membranes capable of separating CO2 from industrial gas streams at higher temperatures. The novel membrane design seeks to leverage the well-researched high-temperature CO2 adsorbent, hydrotalcite, by transforming it into a membrane. This is achieved by combining it with an amorphous organo-silica-based matrix, extending the polymer-based Mixed Matrix Membrane concept to inorganic compounds. Following the membrane material preparation and investigation of the individual membrane in Part 1 of this study, we examine its permeation and selectivity here. The pure 200 nm thick hydrotalcite membrane exhibits Knudsen behavior due to large intercrystalline pores. In contrast, the organo-silica membrane demonstrates a permselectivity of 13.5 and permeance for CO2 of 1.3 107 mol m2 s1 Pa1 at 25°C, at 150°C the good separation behavior is reduced. Combining both components results in a hybrid microstructure, featuring selective surface diffusion in the microporous regions and unselective Knudsen diffusion in the mesoporous regions. Further attempts to bridge both components to form a purely microporous microstructure are outlined.

This study describes the synthesis and characterization of mixed hydrotalcite–organosilica membrane for gas separation. Hydrotalcite exhibits the capability to adsorb carbon dioxide at elevated temperatures. High surface area and favorable coating properties are essential to harness its potential for practical applications. Stable alcohol-based dispersions are needed for thin film applications of mixed membranes containing hydrotalcite. Currently, producing such dispersions without the need for delamination and dispersion agents is a challenging task. This work introduces for the first time a manufacturing approach to overcoming the drawbacks mentioned above. It includes a synthesis of hydrotalcite nanoparticles, followed by agent-free delamination of their layers and final dispersion into alcohol without dispersion agents. Further, the hydrotalcite-derived sorption agent is dispersed in a matrix based on organo-silica gels derived from 1,2-bis(triethoxysilyl)ethane (BTESE). The analytical results indicate that the interconnection between hydrotalcite and BTESE-derived gel occurs via forming a strong hydrogen bonding system between the interlayer species (OH groups, CO32-) of hydrotalcite and oxygen and silanol active gel centers. These findings lay the foundation for applications involving incorporating hydrotalcite-like compounds into silica matrices, ultimately enabling the development of materials with exceptional mass transfer properties. In part 2 of this study, gas separation performance of the organo-silica and the hydrotalcite-like materials and their combined form will be investigated

Walls-like structured monoclinic WO3 thin films were obtained by spray deposition method for further integration in gas sensors. For sensing applications, it is very important to achieve a high surface-to-volume ratio surface together with a proper thin films structure. The present communication reports on the effect of the sprayed solution volume variation (as a thickness variation element) on the detailed Raman spectroscopy for WO3 thin films with different thicknesses grown from precursor solutions with two different concentrations. Detailed analysis of the two series of samples shows that the growing thickness strongly affects the films morphology while their crystalline structure is only slightly affected. The Raman analysis contribute to refining the structural features clarifications. It was observed that, for both concentrations, the increase in thickness seems to slightly affect the stoichiometry of material and, in association with surface morphology variations, provide new possibilities for fine tuning of films properties towards enhanced as sensing applications. Further studies are ongoing.

The success of composite materials is attributed to the nature of bonding at the nanoscale and the resulting structure-related properties. This study reports the interaction, electronic, and optical properties of diamond nanothread/polymers (cellulose and epoxy) and boron nitride nanotube/calcium silicate hydrate composites using density functional theory modeling. Our findings indicate that the interaction between the nanothread and polymer is due to van der Waals-type bonding. Minor modifications in the electronic structures and absorption spectra are noticed. Conversely, the boron nitride nanotube and calcium silicate hydrate composite display an electron-shared type of interaction. The electronic structure and optical absorption spectra of the diamond nanothread and boron nitride nanotube in all configurations studied in the aforementioned composite systems are well maintained. Our findings offer an electronic-level perspective into the bonding characteristics and electronic-optical properties of diamond nanothread/polymer and boron nitride nanotube/calcium silicate hydrate composites for developing next-generation materials.

In this paper, we present the characteristics of photoluminescent YBO3 successfully synthesized through a solid-state reaction and microwave-assisted method. We used yttrium oxide and boric acid in excess as starting reagents. The synthesis conditions are reflected in fluorescent characteristics and the structure. Excess boric acid causes structural changes, as observed by the FTIR spectroscopy analysis. The FTIR spectra analysis of the structure provided valuable insights into the phase composition and modifications induced by varying amounts of boric acid and synthesis methods. The identified structural features contribute to the understanding of the synthesized samples' characteristics and their potential applications in various fields such as illumination and displays and narrow-band fluorescent smartphone readable markers.

The terpolymers of N-vinylpyrrolidone (VP) with acrylic acid and triethylene glycol methacrylate were synthesized with more than 90% yield by radical copolymerization in ethanol from monomeric mixtures of different composition (98 : 2 : 2, 95 : 5: 2 and 98 : 2: 5). Their physical and chemical characteristics such as monomer composition, absolute molecular masses and hy-drodynamic radii in aqueous media at different temperature were determined. The temperature effect on the behavior of terpolymers in water and aqueous saline buffer solution with pH 7.4 has been studied and the ability of a copolymer enriched with dimethacrylates units was discovered to respond to a temperature change in these media. On the basis of terpolymers and linear polyvi-nylpyrrolidone (PVP), polymer compositions of hydrophobic dye methyl pheophorbide a, MPP, that is fluorescent in the red region of the spectrum, were obtained; the sizes of the polymer nanostructures of MPP in water were determined. The structures based on terpolymers were demonstrated to be more stable than MPP-PVP ones. It was carried out the quantum-chemical modelling of the possible structures of MPP-copolymer that formed as a result of intermolecular interaction between MPP and terpolymer’s chains; the possibility of the formation of hydrogen bonds between the donors of the electrons of terpolymer units and the proton donors of the MPP molecule was shown. Using the MTT test, it was established that copolymers of various compositions are low toxic for non-tumor Vero cells and HeLa tumor cells. It was shown that the cytotoxicity of polymer particles loaded with MPP for FetMSC and HeLa cells increased. Using fluorescence microscopy, the accumulation and distribution of polymer particles in non-tumor (FetMSC) and tumor (HeLa) cells was studied and an increase in the accumulation of MPP with both types of particles was shown.

Cu-ions dispersed on reduced graphene RGo prepared and characterized in a liquid state in ethanol. Either constant ultrasounds or a sequence of ultrasounds (15s working, 15s stop) were applied for 6 min or 2h overall time, at a power of 500 W. Commercial graphite in ethanol was introduced at a concentration of 0.04 g/mL and CuCl2 2.5 H2O concentrations between 0.012 and 0.04 g/mL were used. The structural characterizations performed by XRD, microscopic, and spectroscopic techniques, after a centrifugation at 5000 rpm applied 12 min before Cu-introduction, led to conclude that: 1) Without copper, negative peaks in UV spectra were detected with concentrated pure graphene solutions, indicating light emission as nicely confirmed next by fluorescence measurements, 2) After addition of copper chloride and equilibration for 2 min , very intense and narrow peaks of intensity larger than 10 were observed. These peaks due to collective excitations generating plasmons were suppressed at a higher dilution and also if the cell with one cm optical path was replaced by a narrower cell with a 0.2 cm path. When plasmons were suppressed, in the UV spectral range, a band gap due to the energy transition between the valence filled  orbitals and conducting empty * orbitals, was observed. The presence of Cu (II) and Cu (I) cations were evidenced by Visible NIR spectroscopy. The formed “green” liquors containing Cu (II) Cu (I) /graphene in ethanol were stable in air for months and had good photocatalytic visible properties as demonstrated by the decomposition of two dyes.

A modification to the conventional spark plasma sintering (SPS) process was undertaken to allow edge-free deformation of grains longitudinally to the loading axis in a process termed spark plasma texturing (SPT). The resulting Al7075 SPT compact was compared to SPSed Al7075 in terms of densification behaviour, microstructural evolution, and mechanical properties. The result reported herein highlights the unique benefits of the SPT technique and potential application in the manufacturing of advanced materials.

Cultural heritage is a fundamental part of the society’s identity, and its conservation is of great relevance as it transcends time and memory. To minimize its deterioration, cultural heritage has traditionally undergone diverse preservation and maintenance treatments and the attention of researchers to develop new and innovative methods for state diagnosis and protection treatments has been increasing in the recent decades. Therefore, in this study, a literature review using a bibliometric analysis and LDA methodology was conducted to systematically map scientific research outputs on cultural heritage conservation and protection. Data was retrieved from the Scopus database and the annual publications, countries, most-cited publications, authors, institutions, and keywords have been comprehensively analyzed, leading to the detection of research trends. Findings show an increasing number of studies in this field in the last decades, particularly since 2010. Italy, home to the largest number of UNESCO heritage sites, is the most prolific country. Most of the studies are related to metal, paper and stone as substrate to be protected. Significant progress has been made in understanding the deterioration processes through precise diagnosis and the development of innovative treatments for protection. In this sense, latest trends have been detected such as the use of non-invasive techniques for diagnosis and the use of nanotechnology and nature-based treatments for the conservation treatments.

A better understanding of high temperature processes in slags contributes to facilitate knowledge based design of the solidified product. Here, a slag analogue with a nominal composition of 17 wt% LiMnO2 and 83 wt% Ca2SiO4 was synthesized encountering fairly high cooling rates. The Mn species from 1223 K to 1773 K was simulated using a thermodynamic model assuming a homogeneous melt. The micro-composition including the Mn species of the solidified slag was determined experimentally and was used as basis for molecular dynamics (MD) simulation. The MD simulation provides information on structure and viscosity at high temperatures, otherwise difficult to access. These parameters significantly influence oxidation state of redox-active elements and the solidified product. The micro-composition analyzed by electron probe micro analysis (EPMA) and synchrotron based micro-X-ray fluorescence (micro-XRF) showed that Mn-rich and Ca-Si-rich phases are separated. While the Mn-O phases did not contain noticeable Ca, the Ca2SiO4 phase had incorporated 0.6 wt% of Mn. The slag solidified into round shaped and droplet shaped grains of a Li-Mn-oxide, some Mn3O4 and Ca2SiO4. The powder X-ray diffraction (PXRD) confirmed the formation of larnite, the identity of the Li-Mn-oxide however remained inconclusive. The Mn oxidation state (OS) was identified using synchrotron based micro-X-ray absorption near edge spectroscopy (micro-XANES). The Mn-O grains, matched well with Li-Mn-oxides and a Mn OS: +3 e.g. LiMn3+O2. Small areas matching Hausmannite (Mn2+Mn23+O4) were also identified. The OS of Mn in the silicate phase could not be identified. For comparison a slowly cooled slag analogue with similar composition however higher Si content, was also subjected to micro-XANES. The slowly cooled slag formed long Mn-rich needles in a matrix of large calcium silicate crystals. The Mn-rich crystals matched well with the XANES spectrum of a Mn3+ Li-oxide like LiMn3+O2. At the rim of the needles the Mn-spectra matched well the Hausmannite (Mn2+Mn23+O4) reference. In the silicate phases Mn had a OS: +2, unambiguously. The melt structure at different temperatures of two compositions i.e. LiMn3+O2 and Ca2SiO4 was simulated using molecular dynamics (MD). They serve as model compositions assuming a heterogeneous melt. The results show significant different degrees of polymerization and viscosity. Information from MD simulations can support the identification of potentially different oxygen permeability and with that prediction of oxidation states. The bulk composition was identified by inductively coupled plasma optical emission spectrometry (ICP-OES), bulk structure by PXRD and bulk species by lab-XANES. The synchrotron micro analysis including micro-XRD were performed at the microfocus beamline I18 at the Diamond Light Source. Pure reference compounds were prepared and characterized with the same multi-modal approach.

Aiming at the removal of radioactive cobalt ions from water by graphene oxide (GO), the adsorption mechanism of Co2+ on graphene oxide was analyzed using the quantum chemical calculation software Gaussian 16 based on the density functional theory. The influence of material structure factors such as carboxyl group, hydroxyl group, epoxy group and graphene sheet as well as external environmental factors such as pH, temperature and interfering ions on the adsorption effect was determined, and the influence of external environment was verified through experiments. Through calculation and experiment, it was found that the existence of oxygen-containing functional groups on graphene oxide can improve the adsorption efficiency of the materialappropriately,and increasing pH under acidic conditions was also helpful to improve the adsorption effect, and the material had certain selectivity for Co2+, the adsorption capacity and selectivity could be further improved when it was modified by increasing hydroxyl group.

Solid-state batteries (SSBs) have emerged as a promising alternative to conventional lithium-ion batteries, with notable advantages in safety, energy density, and longevity, yet the environmental implications of their lifecycle, from manufacturing to disposal, remain a critical concern. This review paper examines the environmental impacts associated with the production, use, and end-of-life management of SSBs, starting with the extraction and processing of raw materials which highlights significant natural resource consumption, energy use, and emissions. A comparative analysis with traditional battery manufacturing underscores the environmental hazards of novel materials specific to SSBs. The review also assesses the operational environmental impact of SSBs by evaluating their energy efficiency and carbon footprint in comparison to conventional batteries, followed by an exploration of end-of-life challenges including disposal risks, regulatory frameworks, and the shortcomings of existing waste management practices. A significant focus is placed on recycling and reuse strategies, reviewing current methodologies like mechanical, pyrometallurgical, and hydrometallurgical processes, along with emerging technologies that aim to overcome recycling barriers, while also analyzing the economic and technological challenges of these processes. Additionally, real-world case studies are presented, serving as benchmarks for best practices and highlighting lessons learned in the field. In conclusion, the paper identifies research gaps and future directions for reducing the environmental footprint of SSBs, underscoring the need for interdisciplinary collaboration to advance sustainable SSB technologies and contribute to balancing technological advancements with environmental stewardship, thereby supporting the transition to a more sustainable energy future.

In this work, the surface of poly(ethylene terephthalate) track-etched membranes (PET TeMs) with pore sizes of 670-1310 nm was hydrophobized with 2,2,3,3,4,4,5,5,6,6,7,7-dodecafluoroheptyl acrylate (DFHA) by photoinitiated graft polymerization. Attenuated total reflection FTIR spec-troscopy (ATR-FTIR), scanning electron microscopy (SEM) coupled to an energy-dispersive X-ray spectrometer (EDX), and contact angle measurement were used to identify and characterize the TeMs. The optimal parameters for graft polymerization were determined as follows: polymeriza-tion time 60 min, monomer concentration of 30% and distance from the UV-source 7 cm. The wa-ter contact angle of the modified membranes reached 97° which is 51o for pristine membranes. The modified membranes were tested for water desalination using direct contact membrane distillation (DCMD) method. The effect of membrane pore size, the degree of grafting and salt concentration on the performance of membrane distillation process was investigated. According to the results obtained, it has been concluded that large pore size hydrophobic TeMs modified by using DFHA could be used for desalinating water.

Chemical vapor deposition (CVD) is a vital process for depositing thin films of various materials with precise control over thickness, composition, and properties. Understanding the heat and mass transfer mechanisms during CVD is essential for optimizing process parameters and ensuring high-quality film deposition. This review provides an overview of recent advancements in the heat and mass transfer modeling for chemical vapor deposition processes. It explores innovative modeling techniques, recent research findings, emerging applications, and challenges in the field. Additionally, it discusses future directions and potential areas for further advancement in CVD modeling.

Antibiotic-loaded bone cement (ALBC) plays a pivotal role in infection prevention and treatment related to musculoskeletal surgery. The release efficacy of antibiotics from ALBC is closely tied to its surface area, yet little is known about the effective release depth. To investigate the relationship between surface area, volume, and antibiotic elution, spheric ALBC specimens with consistent outer diameters but different internal metal sphere diameters were prepared. Two vancomycin doses were utilized in ALBC specimens with an outer diameter of 35 mm: high (4 g) and low (1 g). Each dosage group included five specimens containing embedded metal spheres with diameters of 15, 25, 29, 32, or 33 mm. The resulting shell-like ALBC specimens had thicknesses of 10 mm, 5 mm, 3 mm, 1.5 mm, or 1 mm, respectively. The specimens were immersed in sterile phosphate buffer solution, and antibiotic elution was measured at designated sampling times (1, 3, 6, 10, 24, 48, 72, and 168 hours). Methylene blue was employed to visualize penetration depth. Vancomycin elution did not display statistically significant differences between high- and low-dose groups. In both groups, specimens with 1 mm thickness exhibited a higher vancomycin release efficiency (high-dose group: 18560±5474 μg, 6.7%; low-dose group: 2017±419 μg, 2.6%), decreasing sharply in thicker ALBC specimens. Methylene blue penetration depth showed no apparent difference between high-dose and low-dose groups. ALBC thickness does not significantly impact antibiotic elution, while surface area and antibiotic dose exert notable effects. These in vitro findings offer potential applications in clinical treatments for musculoskeletal infections.

As a new type of high-performance material, gradient structural steel is widely used in engineering fields due to its unique microstructure and excellent mechanical properties. For the prevalent fatigue failure problem, the rate of change of the local grain size gradients along the structure (referred to as the gradient rate) is a key parameter in the design of gradient structures, which significantly affects the fatigue performance of gradient structural steel. In this work, a method of ‘Voronoi primary + secondary modeling’ is adopted to successfully establish three typical high-strength steel models corresponding to the convex, linear, and concave type gradient rates for gradient structures, focusing on the stress-strain response and crack propagation in structural steel with different gradient rates under cyclic loading. It is found that the concave gradient rate structural model is dominated by finer grains with larger volume fraction, which is conducive to hindering fatigue crack propagation and has the longest fatigue life; the linear structure is the second one, and the convex structure is the shortest one. The simulation results in this work are consistent with the relevant experimental phenomena. Therefore, when regulating the gradient rate, priority should be given to increasing the volume fraction of fine grains and designing a gradient rate structure dominated by fine grains to improve the fatigue life of the material.